alsa-devel.alsa-project.org archive mirror
 help / color / mirror / Atom feed
From: Dan Murphy <dmurphy@ti.com>
To: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>,
	<alsa-devel@alsa-project.org>
Cc: cezary.rojewski@intel.com, a-estrada@ti.com,
	andriy.shevchenko@intel.com, tiwai@suse.com,
	jee.heng.sia@intel.com, pierre-louis.bossart@linux.intel.com,
	liam.r.girdwood@linux.intel.com, broonie@kernel.org,
	zakkaye@ti.com
Subject: Re: [PATCH 3/3] ASoC: codec: tlv3204: Moving GPIO reset and add ADC reset
Date: Wed, 29 Jul 2020 07:31:00 -0500	[thread overview]
Message-ID: <e97b37d1-548e-6ede-4015-563d4f67f5e6@ti.com> (raw)
In-Reply-To: <20200729073256.24028-4-michael.wei.hong.sit@intel.com>

Hello

On 7/29/20 2:32 AM, Michael Sit Wei Hong wrote:
> Moving GPIO reset to a later stage and before clock registration to
> ensure that the host system and codec clocks are in sync. If the host
> register clock values prior to gpio reset, the last configured codec clock
> is registered to the host. The codec then gets gpio resetted setting the
> codec clocks to their default value, causing a mismatch. Host system will
> skip clock setting thinking the codec clocks are already at the requested
> rate.
>
> ADC reset is added to ensure the next audio capture does not have
> undesired artifacts. It is probably related to the original code
> where the probe function resets the ADC prior to 1st record.
>
> Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
> Reviewed-by: Sia Jee Heng <jee.heng.sia@intel.com>
> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
> ---
>   sound/soc/codecs/tlv320aic32x4.c | 47 ++++++++++++++++++++++++--------
>   1 file changed, 35 insertions(+), 12 deletions(-)
>
> diff --git a/sound/soc/codecs/tlv320aic32x4.c b/sound/soc/codecs/tlv320aic32x4.c
> index 5af438a00f95..37e14558d7c0 100644
> --- a/sound/soc/codecs/tlv320aic32x4.c
> +++ b/sound/soc/codecs/tlv320aic32x4.c
> @@ -50,6 +50,28 @@ struct aic32x4_priv {
>   	struct device *dev;
>   };
>   
> +static int aic32x4_reset_adc(struct snd_soc_dapm_widget *w,
> +			     struct snd_kcontrol *kcontrol, int event)
> +{
> +	struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
> +	u32 adc_reg;
> +
> +	/*
> +	 * Workaround: the datasheet does not mention a required programming
> +	 * sequence but experiments show the ADC needs to be reset after each
> +	 * capture to avoid audible artifacts.
> +	 */
> +	switch (event) {
> +	case SND_SOC_DAPM_POST_PMD:
> +		adc_reg = snd_soc_component_read32(component, AIC32X4_ADCSETUP);

This gives me a build error

sound/soc/codecs/tlv320aic32x4.c: In function ‘aic32x4_reset_adc’:
sound/soc/codecs/tlv320aic32x4.c:66:13: error: implicit declaration of 
function ‘snd_soc_component_read32’; did you mean 
‘snd_soc_component_read’? [-Werror=implicit-function-declaration]
    66 |   adc_reg = snd_soc_component_read32(component, AIC32X4_ADCSETUP);
       |             ^~~~~~~~~~~~~~~~~~~~~~~~
       |             snd_soc_component_read

Also you should check the return to make sure it is valid.

Dan



  reply	other threads:[~2020-07-29 12:32 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-07-29  7:32 [PATCH 0/3] ASoC: codec: tlv3204: Codec workaround Michael Sit Wei Hong
2020-07-29  7:32 ` [PATCH 1/3] ASoC: codec: tlv3204: Enable 24 bit audio support Michael Sit Wei Hong
2020-07-29  7:32 ` [PATCH 2/3] ASoC: codec: tlv3204: Increased maximum supported channels Michael Sit Wei Hong
2020-07-29  7:32 ` [PATCH 3/3] ASoC: codec: tlv3204: Moving GPIO reset and add ADC reset Michael Sit Wei Hong
2020-07-29 12:31   ` Dan Murphy [this message]
2020-07-30  5:46     ` Sit, Michael Wei Hong
2020-07-30 12:33       ` Mark Brown
2020-08-03  1:54         ` Sit, Michael Wei Hong
2020-08-03  8:15           ` Shevchenko, Andriy
2020-08-03 10:44           ` Mark Brown
2020-08-04 10:31           ` Sit, Michael Wei Hong

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=e97b37d1-548e-6ede-4015-563d4f67f5e6@ti.com \
    --to=dmurphy@ti.com \
    --cc=a-estrada@ti.com \
    --cc=alsa-devel@alsa-project.org \
    --cc=andriy.shevchenko@intel.com \
    --cc=broonie@kernel.org \
    --cc=cezary.rojewski@intel.com \
    --cc=jee.heng.sia@intel.com \
    --cc=liam.r.girdwood@linux.intel.com \
    --cc=michael.wei.hong.sit@intel.com \
    --cc=pierre-louis.bossart@linux.intel.com \
    --cc=tiwai@suse.com \
    --cc=zakkaye@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).