* [BUG] SoftAP: zero speed between clients on QCA6174
@ 2023-01-10 9:10 dukzcry
2023-01-12 19:12 ` dukzcry
0 siblings, 1 reply; 5+ messages in thread
From: dukzcry @ 2023-01-10 9:10 UTC (permalink / raw)
To: ath10k
I have the Qualcomm Atheros QCNFA344A M2 module
$ lspci
02:00.0 Network controller: Qualcomm Atheros QCA6174 802.11ac Wireless
Network Adapter (rev 32)
$ dmesg | grep ath10k
[ 3.445810] ath10k_pci 0000:02:00.0: enabling device (0000 -> 0002)
[ 3.446081] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2
irq_mode 0 reset_mode 0
[ 3.680848] ath10k_pci 0000:02:00.0: qca6174 hw3.2 target 0x05030000
chip_id 0x00340aff sub 1028:0310
[ 3.680851] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 0
tracing 0 dfs 0 testmode 0
[ 3.681176] ath10k_pci 0000:02:00.0: firmware ver WLAN.RM.4.4.1-
00288- api 6 features wowlan,ignore-otp,mfp crc32 bf907c7c
[ 3.748580] ath10k_pci 0000:02:00.0: board_file api 2 bmi_id N/A
crc32 62812cba
[ 3.840194] ath10k_pci 0000:02:00.0: htt-ver 3.87 wmi-op 4 htt-op 3
cal otp max-sta 32 raw 0 hwcrypto 1
[ 3.900322] ath10k_pci 0000:02:00.0 wlp2s0: renamed from wlan0
Now I create an AP on it either via hostapd or NetworkManager like
"sudo nmcli dev wifi hotspot ifname wlp2s0 ssid test password "mypass""
Then I connect few various clients to it and benchmark speed from any
client to AP via iperf3, which is fine
Connecting to host 10.42.0.1, port 5201
[ 5] local 10.42.0.19 port 60646 connected to 10.42.0.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 3.89 MBytes 32.6 Mbits/sec 0 208 KBytes
[ 5] 1.00-2.00 sec 4.04 MBytes 33.9 Mbits/sec 0 331 KBytes
[ 5] 2.00-3.00 sec 3.23 MBytes 27.1 Mbits/sec 6 280 KBytes
[ 5] 3.00-4.00 sec 3.04 MBytes 25.5 Mbits/sec 1 308 KBytes
[ 5] 4.00-5.00 sec 4.16 MBytes 34.9 Mbits/sec 0 378 KBytes
[ 5] 5.00-6.00 sec 4.04 MBytes 33.9 Mbits/sec 0 411 KBytes
[ 5] 6.00-7.00 sec 4.16 MBytes 34.9 Mbits/sec 0 411 KBytes
[ 5] 7.00-8.00 sec 2.67 MBytes 22.4 Mbits/sec 0 436 KBytes
[ 5] 8.00-9.00 sec 3.85 MBytes 32.3 Mbits/sec 0 458 KBytes
[ 5] 9.00-10.00 sec 2.92 MBytes 24.5 Mbits/sec 0 458 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 36.0 MBytes 30.2 Mbits/sec 7
sender
[ 5] 0.00-10.02 sec 34.0 MBytes 28.4 Mbits/sec
receiver
iperf Done.
Now I try to measure speed between any two clients and get
Connecting to host 10.42.0.83, port 5201
[ 5] local 10.42.0.19 port 58262 connected to 10.42.0.83 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 414 KBytes 3.39 Mbits/sec 7 7.07 KBytes
[ 5] 1.00-2.00 sec 0.00 Bytes 0.00 bits/sec 12 2.83 KBytes
[ 5] 2.00-3.00 sec 0.00 Bytes 0.00 bits/sec 16 4.24 KBytes
[ 5] 3.00-4.00 sec 0.00 Bytes 0.00 bits/sec 8 15.6 KBytes
[ 5] 4.00-5.00 sec 0.00 Bytes 0.00 bits/sec 13 2.83 KBytes
[ 5] 5.00-6.00 sec 0.00 Bytes 0.00 bits/sec 11 4.24 KBytes
[ 5] 6.00-7.00 sec 0.00 Bytes 0.00 bits/sec 7 2.83 KBytes
[ 5] 7.00-8.00 sec 0.00 Bytes 0.00 bits/sec 4 4.24 KBytes
[ 5] 8.00-9.00 sec 127 KBytes 1.04 Mbits/sec 3 2.83 KBytes
[ 5] 9.00-10.00 sec 0.00 Bytes 0.00 bits/sec 4 2.83 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 542 KBytes 444 Kbits/sec 85
sender
[ 5] 0.00-10.01 sec 277 KBytes 227 Kbits/sec
receiver
iperf Done.
Which is a way too low. Ssh is also very slow between clients, VNC
shows similar speed rates and unable to render desktop at that speed
for sure
The system is totally stock and clean. I also have USB ath9k adapter in
this system, which doesn't show this issue
$ lsusb
Bus 001 Device 004: ID 0cf3:9271 Qualcomm Atheros Communications AR9271
802.11n
$ dmesg | grep ath9k
[ 3.446722] usb 1-3.3: ath9k_htc: Firmware ath9k_htc/htc_9271-
1.4.0.fw requested
[ 3.446804] usbcore: registered new interface driver ath9k_htc
[ 3.734857] usb 1-3.3: ath9k_htc: Transferred FW:
ath9k_htc/htc_9271-1.4.0.fw, size: 51008
[ 3.985462] ath9k_htc 1-3.3:1.0: ath9k_htc: HTC initialized with 33
credits
[ 4.212339] ath9k_htc 1-3.3:1.0: ath9k_htc: FW Version: 1.4
[ 4.212343] ath9k_htc 1-3.3:1.0: FW RMW support: On
[ 4.217755] ath9k_htc 1-3.3:1.0 legacy: renamed from wlan0
Speed between two clients is fine for it
Connecting to host 10.42.1.83, port 5201
[ 5] local 10.42.1.19 port 43456 connected to 10.42.1.83 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 1.43 MBytes 12.0 Mbits/sec 0 107 KBytes
[ 5] 1.00-2.00 sec 1.55 MBytes 13.0 Mbits/sec 0 165 KBytes
[ 5] 2.00-3.00 sec 1.24 MBytes 10.4 Mbits/sec 0 208 KBytes
[ 5] 3.00-4.00 sec 1018 KBytes 8.34 Mbits/sec 0 247 KBytes
[ 5] 4.00-5.00 sec 509 KBytes 4.17 Mbits/sec 19 198 KBytes
[ 5] 5.00-6.00 sec 1.12 MBytes 9.39 Mbits/sec 0 232 KBytes
[ 5] 6.00-7.00 sec 1.68 MBytes 14.1 Mbits/sec 0 252 KBytes
[ 5] 7.00-8.00 sec 573 KBytes 4.69 Mbits/sec 0 259 KBytes
[ 5] 8.00-9.00 sec 1.12 MBytes 9.38 Mbits/sec 0 264 KBytes
[ 5] 9.00-10.00 sec 1.12 MBytes 9.39 Mbits/sec 0 264 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 11.3 MBytes 9.49 Mbits/sec 19
sender
[ 5] 0.00-10.11 sec 10.4 MBytes 8.59 Mbits/sec
receiver
iperf Done.
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [BUG] SoftAP: zero speed between clients on QCA6174
2023-01-10 9:10 [BUG] SoftAP: zero speed between clients on QCA6174 dukzcry
@ 2023-01-12 19:12 ` dukzcry
2023-03-20 18:43 ` Kalle Valo
0 siblings, 1 reply; 5+ messages in thread
From: dukzcry @ 2023-01-12 19:12 UTC (permalink / raw)
To: ath10k; +Cc: kvalo
Looks like firmware issue. Fixed by downgrading linux-firmware package
down to 20220411
Last good firmware
linux-firmware-20220411
[ 3.859587] ath10k_pci 0000:02:00.0: firmware ver WLAN.RM.4.4.1-
00157-QCARMSWPZ-1 api 6 features wowlan,ignore-otp,mfp crc32 90eebefb
[ 3.926126] ath10k_pci 0000:02:00.0: board_file api 2 bmi_id N/A
crc32 706c395e
[ 4.017441] ath10k_pci 0000:02:00.0: htt-ver 3.60 wmi-op 4 htt-op 3
cal otp max-sta 32 raw 0 hwcrypto 1
Connecting to host li-si-tsin, port 5201
[ 7] local 10.0.0.230 port 46036 connected to 10.0.0.50 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 7] 0.00-1.00 sec 16.5 MBytes 138 Mbits/sec 0 789 KBytes
[ 7] 1.00-2.00 sec 15.0 MBytes 126 Mbits/sec 0 1.15 MBytes
[ 7] 2.00-3.00 sec 15.0 MBytes 126 Mbits/sec 0 1.38 MBytes
[ 7] 3.00-4.00 sec 16.2 MBytes 136 Mbits/sec 0 1.54 MBytes
[ 7] 4.00-5.00 sec 16.2 MBytes 136 Mbits/sec 0 1.54 MBytes
[ 7] 5.00-6.00 sec 16.2 MBytes 136 Mbits/sec 0 1.54 MBytes
[ 7] 6.00-7.00 sec 16.2 MBytes 136 Mbits/sec 0 1.60 MBytes
[ 7] 7.00-8.00 sec 15.0 MBytes 126 Mbits/sec 36 1.22 MBytes
[ 7] 8.00-9.00 sec 17.5 MBytes 147 Mbits/sec 0 1.34 MBytes
[ 7] 9.00-10.00 sec 16.2 MBytes 136 Mbits/sec 0 1.39 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 7] 0.00-10.00 sec 160 MBytes 134 Mbits/sec 36
sender
[ 7] 0.00-10.01 sec 157 MBytes 132 Mbits/sec
receiver
iperf Done.
First bad firmware
linux-firmware-20220509
[ 3.767713] ath10k_pci 0000:02:00.0: firmware ver WLAN.RM.4.4.1-
00288- api 6 features wowlan,ignore-otp,mfp crc32 bf907c7c
[ 3.835130] ath10k_pci 0000:02:00.0: board_file api 2 bmi_id N/A
crc32 62812cba
[ 3.927381] ath10k_pci 0000:02:00.0: htt-ver 3.87 wmi-op 4 htt-op 3
cal otp max-sta 32 raw 0 hwcrypto 1
Connecting to host li-si-tsin, port 5201
[ 7] local 10.0.0.230 port 56856 connected to 10.0.0.50 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 7] 0.00-1.00 sec 107 KBytes 879 Kbits/sec 12 11.3 KBytes
[ 7] 1.00-2.00 sec 158 KBytes 1.30 Mbits/sec 0 17.0 KBytes
[ 7] 2.00-3.00 sec 205 KBytes 1.68 Mbits/sec 0 22.6 KBytes
[ 7] 3.00-4.00 sec 67.9 KBytes 556 Kbits/sec 11 5.66 KBytes
[ 7] 4.00-5.00 sec 127 KBytes 1.04 Mbits/sec 3 5.66 KBytes
[ 7] 5.00-6.00 sec 191 KBytes 1.56 Mbits/sec 7 8.48 KBytes
[ 7] 6.00-7.00 sec 127 KBytes 1.04 Mbits/sec 6 11.3 KBytes
[ 7] 7.00-8.00 sec 63.6 KBytes 521 Kbits/sec 8 5.66 KBytes
[ 7] 8.00-9.00 sec 191 KBytes 1.56 Mbits/sec 6 4.24 KBytes
[ 7] 9.00-10.00 sec 127 KBytes 1.04 Mbits/sec 4 7.07 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 7] 0.00-10.00 sec 1.33 MBytes 1.12 Mbits/sec 57
sender
[ 7] 0.00-10.17 sec 1.23 MBytes 1.02 Mbits/sec
receiver
В Вт, 10/01/2023 в 12:10 +0300, dukzcry@ya.ru пишет:
> I have the Qualcomm Atheros QCNFA344A M2 module
>
> $ lspci
> 02:00.0 Network controller: Qualcomm Atheros QCA6174 802.11ac
> Wireless
> Network Adapter (rev 32)
>
> $ dmesg | grep ath10k
> [ 3.445810] ath10k_pci 0000:02:00.0: enabling device (0000 ->
> 0002)
> [ 3.446081] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2
> irq_mode 0 reset_mode 0
> [ 3.680848] ath10k_pci 0000:02:00.0: qca6174 hw3.2 target
> 0x05030000
> chip_id 0x00340aff sub 1028:0310
> [ 3.680851] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 0
> tracing 0 dfs 0 testmode 0
> [ 3.681176] ath10k_pci 0000:02:00.0: firmware ver WLAN.RM.4.4.1-
> 00288- api 6 features wowlan,ignore-otp,mfp crc32 bf907c7c
> [ 3.748580] ath10k_pci 0000:02:00.0: board_file api 2 bmi_id N/A
> crc32 62812cba
> [ 3.840194] ath10k_pci 0000:02:00.0: htt-ver 3.87 wmi-op 4 htt-op
> 3
> cal otp max-sta 32 raw 0 hwcrypto 1
> [ 3.900322] ath10k_pci 0000:02:00.0 wlp2s0: renamed from wlan0
>
> Now I create an AP on it either via hostapd or NetworkManager like
> "sudo nmcli dev wifi hotspot ifname wlp2s0 ssid test password
> "mypass""
>
> Then I connect few various clients to it and benchmark speed from any
> client to AP via iperf3, which is fine
>
> Connecting to host 10.42.0.1, port 5201
> [ 5] local 10.42.0.19 port 60646 connected to 10.42.0.1 port 5201
> [ ID] Interval Transfer Bitrate Retr Cwnd
> [ 5] 0.00-1.00 sec 3.89 MBytes 32.6 Mbits/sec 0 208
> KBytes
> [ 5] 1.00-2.00 sec 4.04 MBytes 33.9 Mbits/sec 0 331
> KBytes
> [ 5] 2.00-3.00 sec 3.23 MBytes 27.1 Mbits/sec 6 280
> KBytes
> [ 5] 3.00-4.00 sec 3.04 MBytes 25.5 Mbits/sec 1 308
> KBytes
> [ 5] 4.00-5.00 sec 4.16 MBytes 34.9 Mbits/sec 0 378
> KBytes
> [ 5] 5.00-6.00 sec 4.04 MBytes 33.9 Mbits/sec 0 411
> KBytes
> [ 5] 6.00-7.00 sec 4.16 MBytes 34.9 Mbits/sec 0 411
> KBytes
> [ 5] 7.00-8.00 sec 2.67 MBytes 22.4 Mbits/sec 0 436
> KBytes
> [ 5] 8.00-9.00 sec 3.85 MBytes 32.3 Mbits/sec 0 458
> KBytes
> [ 5] 9.00-10.00 sec 2.92 MBytes 24.5 Mbits/sec 0 458
> KBytes
> - - - - - - - - - - - - - - - - - - - - - - - - -
> [ ID] Interval Transfer Bitrate Retr
> [ 5] 0.00-10.00 sec 36.0 MBytes 30.2 Mbits/sec 7
> sender
> [ 5] 0.00-10.02 sec 34.0 MBytes 28.4 Mbits/sec
> receiver
>
> iperf Done.
>
>
> Now I try to measure speed between any two clients and get
>
> Connecting to host 10.42.0.83, port 5201
> [ 5] local 10.42.0.19 port 58262 connected to 10.42.0.83 port 5201
> [ ID] Interval Transfer Bitrate Retr Cwnd
> [ 5] 0.00-1.00 sec 414 KBytes 3.39 Mbits/sec 7 7.07
> KBytes
> [ 5] 1.00-2.00 sec 0.00 Bytes 0.00 bits/sec 12 2.83 KBytes
> [ 5] 2.00-3.00 sec 0.00 Bytes 0.00 bits/sec 16 4.24 KBytes
> [ 5] 3.00-4.00 sec 0.00 Bytes 0.00 bits/sec 8 15.6 KBytes
> [ 5] 4.00-5.00 sec 0.00 Bytes 0.00 bits/sec 13 2.83 KBytes
> [ 5] 5.00-6.00 sec 0.00 Bytes 0.00 bits/sec 11 4.24 KBytes
> [ 5] 6.00-7.00 sec 0.00 Bytes 0.00 bits/sec 7 2.83 KBytes
> [ 5] 7.00-8.00 sec 0.00 Bytes 0.00 bits/sec 4 4.24 KBytes
> [ 5] 8.00-9.00 sec 127 KBytes 1.04 Mbits/sec 3 2.83
> KBytes
> [ 5] 9.00-10.00 sec 0.00 Bytes 0.00 bits/sec 4 2.83 KBytes
> - - - - - - - - - - - - - - - - - - - - - - - - -
> [ ID] Interval Transfer Bitrate Retr
> [ 5] 0.00-10.00 sec 542 KBytes 444 Kbits/sec 85
> sender
> [ 5] 0.00-10.01 sec 277 KBytes 227 Kbits/sec
> receiver
>
> iperf Done.
>
> Which is a way too low. Ssh is also very slow between clients, VNC
> shows similar speed rates and unable to render desktop at that speed
> for sure
>
> The system is totally stock and clean. I also have USB ath9k adapter
> in
> this system, which doesn't show this issue
>
> $ lsusb
> Bus 001 Device 004: ID 0cf3:9271 Qualcomm Atheros Communications
> AR9271
> 802.11n
>
> $ dmesg | grep ath9k
> [ 3.446722] usb 1-3.3: ath9k_htc: Firmware ath9k_htc/htc_9271-
> 1.4.0.fw requested
> [ 3.446804] usbcore: registered new interface driver ath9k_htc
> [ 3.734857] usb 1-3.3: ath9k_htc: Transferred FW:
> ath9k_htc/htc_9271-1.4.0.fw, size: 51008
> [ 3.985462] ath9k_htc 1-3.3:1.0: ath9k_htc: HTC initialized with
> 33
> credits
> [ 4.212339] ath9k_htc 1-3.3:1.0: ath9k_htc: FW Version: 1.4
> [ 4.212343] ath9k_htc 1-3.3:1.0: FW RMW support: On
> [ 4.217755] ath9k_htc 1-3.3:1.0 legacy: renamed from wlan0
>
> Speed between two clients is fine for it
>
> Connecting to host 10.42.1.83, port 5201
> [ 5] local 10.42.1.19 port 43456 connected to 10.42.1.83 port 5201
> [ ID] Interval Transfer Bitrate Retr Cwnd
> [ 5] 0.00-1.00 sec 1.43 MBytes 12.0 Mbits/sec 0 107
> KBytes
> [ 5] 1.00-2.00 sec 1.55 MBytes 13.0 Mbits/sec 0 165
> KBytes
> [ 5] 2.00-3.00 sec 1.24 MBytes 10.4 Mbits/sec 0 208
> KBytes
> [ 5] 3.00-4.00 sec 1018 KBytes 8.34 Mbits/sec 0 247
> KBytes
> [ 5] 4.00-5.00 sec 509 KBytes 4.17 Mbits/sec 19 198
> KBytes
> [ 5] 5.00-6.00 sec 1.12 MBytes 9.39 Mbits/sec 0 232
> KBytes
> [ 5] 6.00-7.00 sec 1.68 MBytes 14.1 Mbits/sec 0 252
> KBytes
> [ 5] 7.00-8.00 sec 573 KBytes 4.69 Mbits/sec 0 259
> KBytes
> [ 5] 8.00-9.00 sec 1.12 MBytes 9.38 Mbits/sec 0 264
> KBytes
> [ 5] 9.00-10.00 sec 1.12 MBytes 9.39 Mbits/sec 0 264
> KBytes
> - - - - - - - - - - - - - - - - - - - - - - - - -
> [ ID] Interval Transfer Bitrate Retr
> [ 5] 0.00-10.00 sec 11.3 MBytes 9.49 Mbits/sec 19
> sender
> [ 5] 0.00-10.11 sec 10.4 MBytes 8.59 Mbits/sec
> receiver
>
> iperf Done.
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [BUG] SoftAP: zero speed between clients on QCA6174
2023-01-12 19:12 ` dukzcry
@ 2023-03-20 18:43 ` Kalle Valo
2023-08-03 12:08 ` Kalle Valo
0 siblings, 1 reply; 5+ messages in thread
From: Kalle Valo @ 2023-03-20 18:43 UTC (permalink / raw)
To: dukzcry; +Cc: ath10k
dukzcry@ya.ru writes:
> Looks like firmware issue. Fixed by downgrading linux-firmware package
> down to 20220411
>
> Last good firmware
> linux-firmware-20220411
> [ 3.859587] ath10k_pci 0000:02:00.0: firmware ver WLAN.RM.4.4.1-
> 00157-QCARMSWPZ-1 api 6 features wowlan,ignore-otp,mfp crc32 90eebefb
[...]
> First bad firmware
> linux-firmware-20220509
> [ 3.767713] ath10k_pci 0000:02:00.0: firmware ver WLAN.RM.4.4.1-
> 00288- api 6 features wowlan,ignore-otp,mfp crc32 bf907c7c
Thanks for the report, I forwarded this and hopefully it gets fixed.
--
https://patchwork.kernel.org/project/linux-wireless/list/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [BUG] SoftAP: zero speed between clients on QCA6174
2023-03-20 18:43 ` Kalle Valo
@ 2023-08-03 12:08 ` Kalle Valo
2023-08-06 18:37 ` dukzcry
0 siblings, 1 reply; 5+ messages in thread
From: Kalle Valo @ 2023-08-03 12:08 UTC (permalink / raw)
To: dukzcry; +Cc: ath10k
Kalle Valo <kvalo@kernel.org> writes:
> dukzcry@ya.ru writes:
>
>> Looks like firmware issue. Fixed by downgrading linux-firmware package
>> down to 20220411
>>
>> Last good firmware
>> linux-firmware-20220411
>> [ 3.859587] ath10k_pci 0000:02:00.0: firmware ver WLAN.RM.4.4.1-
>> 00157-QCARMSWPZ-1 api 6 features wowlan,ignore-otp,mfp crc32 90eebefb
>
> [...]
>
>> First bad firmware
>> linux-firmware-20220509
>> [ 3.767713] ath10k_pci 0000:02:00.0: firmware ver WLAN.RM.4.4.1-
>> 00288- api 6 features wowlan,ignore-otp,mfp crc32 bf907c7c
>
> Thanks for the report, I forwarded this and hopefully it gets fixed.
There's now a new version firmware-6.bin_WLAN.RM.4.4.1-00309- available:
https://github.com/kvalo/ath10k-firmware/tree/master/QCA6174/hw3.0/4.4.1
If you can, please test it and let us know if the issue is fixed or not.
--
https://patchwork.kernel.org/project/linux-wireless/list/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [BUG] SoftAP: zero speed between clients on QCA6174
2023-08-03 12:08 ` Kalle Valo
@ 2023-08-06 18:37 ` dukzcry
0 siblings, 0 replies; 5+ messages in thread
From: dukzcry @ 2023-08-06 18:37 UTC (permalink / raw)
To: Kalle Valo; +Cc: ath10k
В Чт, 03/08/2023 в 15:08 +0300, Kalle Valo пишет:
> > > > Kalle Valo <kvalo@kernel.org> writes:
> > > >
> > > > > > > > dukzcry@ya.ru writes:
> > > > > > > >
> > > > > > > > > > > > Looks like firmware issue. Fixed by downgrading
> > > > > > > > > > > > linux-firmware
> > > > > > > > > > > > package
> > > > > > > > > > > > down to 20220411
> > > > > > > > > > > >
> > > > > > > > > > > > Last good firmware
> > > > > > > > > > > > linux-firmware-20220411
> > > > > > > > > > > > [ 3.859587] ath10k_pci 0000:02:00.0:
> > > > > > > > > > > > firmware ver
> > > > > > > > > > > > WLAN.RM.4.4.1-
> > > > > > > > > > > > 00157-QCARMSWPZ-1 api 6 features wowlan,ignore-
> > > > > > > > > > > > otp,mfp
> > > > > > > > > > > > crc32
> > > > > > > > > > > > 90eebefb
> > > > > > > >
> > > > > > > > [...]
> > > > > > > >
> > > > > > > > > > > > First bad firmware
> > > > > > > > > > > > linux-firmware-20220509
> > > > > > > > > > > > [ 3.767713] ath10k_pci 0000:02:00.0:
> > > > > > > > > > > > firmware ver
> > > > > > > > > > > > WLAN.RM.4.4.1-
> > > > > > > > > > > > 00288- api 6 features wowlan,ignore-otp,mfp
> > > > > > > > > > > > crc32 bf907c7c
> > > > > > > >
> > > > > > > > Thanks for the report, I forwarded this and hopefully
> > > > > > > > it gets
> > > > > > > > fixed.
> > > >
> > > > There's now a new version firmware-6.bin_WLAN.RM.4.4.1-00309-
> > > > available:
> > > >
> > > > https://github.com/kvalo/ath10k-firmware/tree/master/QCA6174/hw3.0/4.4.1
> > > >
> > > > If you can, please test it and let us know if the issue is
> > > > fixed or
> > > > not.
> > > >
Thanks! The issue is fixed with it. Thought noticed that SU-BEAMFORMEE
VHT capability is not supported anymore as reported by hostapd, not
sure if needed though, I just removed it from hostapd config
[ 3.904686] ath10k_pci 0000:02:00.0: firmware ver WLAN.RM.4.4.1-
00309- api 6 features wowlan,ignore-otp,mfp crc32 0793bcf2
hostapd[1394]: Driver does not support configured VHT capability
[VHT_CAP_SU_BEAMFORMEE_CAPABLE]
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2023-08-06 18:43 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-01-10 9:10 [BUG] SoftAP: zero speed between clients on QCA6174 dukzcry
2023-01-12 19:12 ` dukzcry
2023-03-20 18:43 ` Kalle Valo
2023-08-03 12:08 ` Kalle Valo
2023-08-06 18:37 ` dukzcry
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).