b.a.t.m.a.n.lists.open-mesh.org archive mirror
 help / color / mirror / Atom feed
From: Sven Eckelmann <sven@narfation.org>
To: b.a.t.m.a.n@lists.open-mesh.org
Cc: Jiri Pirko <jiri@mellanox.com>,
	netdev@vger.kernel.org, Sven Eckelmann <sven@narfation.org>,
	Simon Wunderlich <sw@simonwunderlich.de>
Subject: [B.A.T.M.A.N.] [RFC v4 08/19] batman-adv: Add bridge_loop_avoidance mesh genl configuration
Date: Sat, 19 Jan 2019 16:56:15 +0100	[thread overview]
Message-ID: <20190119155626.6414-9-sven@narfation.org> (raw)
In-Reply-To: <20190119155626.6414-1-sven@narfation.org>

The mesh interface can try to detect loops in the same mesh caused by
(indirectly) bridged mesh/soft-interfaces of different nodes. Some of the
loops can also be resolved without breaking the mesh.

The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the
BATADV_ATTR_BRIDGE_LOOP_AVOIDANCE_ENABLED attribute. Setting the u8 to zero
will disable this feature and setting it to something else is enabling this
feature.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
---
Cc: Simon Wunderlich <sw@simonwunderlich.de>
---
 include/uapi/linux/batman_adv.h |  7 +++++++
 net/batman-adv/netlink.c        | 17 +++++++++++++++++
 2 files changed, 24 insertions(+)

diff --git a/include/uapi/linux/batman_adv.h b/include/uapi/linux/batman_adv.h
index f74ff261..3cb35c66 100644
--- a/include/uapi/linux/batman_adv.h
+++ b/include/uapi/linux/batman_adv.h
@@ -381,6 +381,13 @@ enum batadv_nl_attrs {
 	 */
 	BATADV_ATTR_BONDING_ENABLED,
 
+	/**
+	 * @BATADV_ATTR_BRIDGE_LOOP_AVOIDANCE_ENABLED: whether the bridge loop
+	 *  avoidance feature is enabled. This feature detects and avoids loops
+	 *  between the mesh and devices bridged with the soft interface
+	 */
+	BATADV_ATTR_BRIDGE_LOOP_AVOIDANCE_ENABLED,
+
 	/* add attributes above here, update the policy in netlink.c */
 
 	/**
diff --git a/net/batman-adv/netlink.c b/net/batman-adv/netlink.c
index 8a309c78..0a29dc75 100644
--- a/net/batman-adv/netlink.c
+++ b/net/batman-adv/netlink.c
@@ -144,6 +144,7 @@ static const struct nla_policy batadv_netlink_policy[NUM_BATADV_ATTR] = {
 	[BATADV_ATTR_ISOLATION_MARK]		= { .type = NLA_U32 },
 	[BATADV_ATTR_ISOLATION_MASK]		= { .type = NLA_U32 },
 	[BATADV_ATTR_BONDING_ENABLED]		= { .type = NLA_U8 },
+	[BATADV_ATTR_BRIDGE_LOOP_AVOIDANCE_ENABLED]	= { .type = NLA_U8 },
 };
 
 /**
@@ -284,6 +285,12 @@ static int batadv_netlink_mesh_put(struct sk_buff *msg,
 		       !!atomic_read(&bat_priv->bonding)))
 		goto nla_put_failure;
 
+#ifdef CONFIG_BATMAN_ADV_BLA
+	if (nla_put_u8(msg, BATADV_ATTR_BRIDGE_LOOP_AVOIDANCE_ENABLED,
+		       !!atomic_read(&bat_priv->bridge_loop_avoidance)))
+		goto nla_put_failure;
+#endif /* CONFIG_BATMAN_ADV_BLA */
+
 	if (primary_if)
 		batadv_hardif_put(primary_if);
 
@@ -398,6 +405,16 @@ static int batadv_netlink_set_mesh(struct sk_buff *skb, struct genl_info *info)
 		atomic_set(&bat_priv->bonding, !!nla_get_u8(attr));
 	}
 
+#ifdef CONFIG_BATMAN_ADV_BLA
+	if (info->attrs[BATADV_ATTR_BRIDGE_LOOP_AVOIDANCE_ENABLED]) {
+		attr = info->attrs[BATADV_ATTR_BRIDGE_LOOP_AVOIDANCE_ENABLED];
+
+		atomic_set(&bat_priv->bridge_loop_avoidance,
+			   !!nla_get_u8(attr));
+		batadv_bla_status_update(bat_priv->soft_iface);
+	}
+#endif /* CONFIG_BATMAN_ADV_BLA */
+
 	batadv_netlink_notify_mesh(bat_priv);
 
 	return 0;
-- 
2.20.1


  parent reply	other threads:[~2019-01-19 15:56 UTC|newest]

Thread overview: 29+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-01-19 15:56 [B.A.T.M.A.N.] [RFC v4 00/19] batman-adv: netlink restructuring, part 2 Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 01/19] batman-adv: Move common genl doit code pre/post hooks Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 02/19] batman-adv: Prepare framework for mesh genl config Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 03/19] batman-adv: Prepare framework for hardif " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 04/19] batman-adv: Prepare framework for vlan " Sven Eckelmann
2019-01-21  9:44   ` Jiri Pirko
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 05/19] batman-adv: Add aggregated_ogms mesh genl configuration Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 06/19] batman-adv: Add ap_isolation mesh/vlan " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 07/19] batman-adv: Add bonding mesh " Sven Eckelmann
2019-01-19 15:56 ` Sven Eckelmann [this message]
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 09/19] batman-adv: Add distributed_arp_table " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 10/19] batman-adv: Add fragmentation " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 11/19] batman-adv: Add gateway " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 12/19] batman-adv: Add hop_penalty " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 13/19] batman-adv: Add log_level " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 14/19] batman-adv: Add multicast_mode " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 15/19] batman-adv: Add network_coding " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 16/19] batman-adv: Add orig_interval " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 17/19] batman-adv: Add elp_interval hardif " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 18/19] batman-adv: Add throughput_override " Sven Eckelmann
2019-01-19 15:56 ` [B.A.T.M.A.N.] [RFC v4 19/19] batman-adv: Trigger genl notification on sysfs config change Sven Eckelmann
2019-01-21  9:47 ` [B.A.T.M.A.N.] [RFC v4 00/19] batman-adv: netlink restructuring, part 2 Jiri Pirko
2019-01-26 10:47 ` Sven Eckelmann
2019-01-27  8:45   ` Jiri Pirko
2019-02-05 17:04   ` Simon Wunderlich
2019-02-05 19:24   ` Linus Lüssing
2019-02-06 18:20     ` Sven Eckelmann
2019-02-06 19:08       ` Linus Lüssing
2019-02-07 10:02         ` Sven Eckelmann

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190119155626.6414-9-sven@narfation.org \
    --to=sven@narfation.org \
    --cc=b.a.t.m.a.n@lists.open-mesh.org \
    --cc=jiri@mellanox.com \
    --cc=netdev@vger.kernel.org \
    --cc=sw@simonwunderlich.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).