[PATCH] batman-adv: Disable CONFIG_BATMAN_ADV_SYSFS by default

[PATCH] batman-adv: Disable CONFIG_BATMAN_ADV_SYSFS by default

[Sven Eckelmann]

The sysfs support in batman-adv is deprecated since a while and will be
removed completely next year.

All tools which were known to the batman-adv development team are
supporting the batman-adv netlink interface since a while. Thus
disabling CONFIG_BATMAN_ADV_SYSFS by default should not cause problems on
most systems. It is still possible to enable it in case it is still
required in a specific setup.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
---
 Makefile               | 2 +-
 README.external.rst    | 2 +-
 net/batman-adv/Kconfig | 1 -
 3 files changed, 2 insertions(+), 3 deletions(-)

diff --git a/Makefile b/Makefile
index e391a1e7..448a14d6 100644
--- a/Makefile
+++ b/Makefile
@@ -17,7 +17,7 @@ export CONFIG_BATMAN_ADV_NC=n
 # B.A.T.M.A.N. multicast optimizations:
 export CONFIG_BATMAN_ADV_MCAST=y
 # B.A.T.M.A.N. sysfs support:
-export CONFIG_BATMAN_ADV_SYSFS=y
+export CONFIG_BATMAN_ADV_SYSFS=n
 # B.A.T.M.A.N. tracing support:
 export CONFIG_BATMAN_ADV_TRACING=n
 # B.A.T.M.A.N. V routing algorithm (experimental):
diff --git a/README.external.rst b/README.external.rst
index 6db0117d..5a5da14e 100644
--- a/README.external.rst
+++ b/README.external.rst
@@ -49,7 +49,7 @@ module).  Available  options  and  their    possible   values are
  * ``CONFIG_BATMAN_ADV_DAT=[y*|n]`` (B.A.T.M.A.N. Distributed ARP Table)
  * ``CONFIG_BATMAN_ADV_MCAST=[y*|n]`` (B.A.T.M.A.N. multicast optimizations)
  * ``CONFIG_BATMAN_ADV_NC=[y|n*]`` (B.A.T.M.A.N. Network Coding)
- * ``CONFIG_BATMAN_ADV_SYSFS=[y*|n]`` (B.A.T.M.A.N. sysfs support)
+ * ``CONFIG_BATMAN_ADV_SYSFS=[y|n*]`` (B.A.T.M.A.N. sysfs support)
  * ``CONFIG_BATMAN_ADV_TRACING=[y|n*]`` (B.A.T.M.A.N. tracing support)
  * ``CONFIG_BATMAN_ADV_BATMAN_V=[y*|n]`` (B.A.T.M.A.N. V routing algorithm)
 
diff --git a/net/batman-adv/Kconfig b/net/batman-adv/Kconfig
index 045b2b18..c762758a 100644
--- a/net/batman-adv/Kconfig
+++ b/net/batman-adv/Kconfig
@@ -100,7 +100,6 @@ config BATMAN_ADV_DEBUG
 config BATMAN_ADV_SYSFS
 	bool "batman-adv sysfs entries"
 	depends on BATMAN_ADV
-	default y
 	help
 	  Say Y here if you want to enable batman-adv device configuration and
 	  status interface through sysfs attributes. It is replaced by the
-- 
2.20.1