* [B.A.T.M.A.N.] br-lan: received packet on bat0 with own address as source address
@ 2014-03-31 20:10 Ilario Gelmetti
2014-04-01 9:33 ` Ilario GELMETTI
0 siblings, 1 reply; 4+ messages in thread
From: Ilario Gelmetti @ 2014-03-31 20:10 UTC (permalink / raw)
To: b.a.t.m.a.n
[-- Attachment #1.1: Type: text/plain, Size: 1479 bytes --]
Hi all,
I have two devices (Ubiquiti PicoStation M2 and Ubiquiti NanoStation M5)
mounted on the same pole both running libre-mesh [1] firmware
(batman-adv: 2014.1.0) and both attached to a Mikrotik RB250GS gigabit
switch (latest 1.11 firmware, default configuration) which is attached
to my pc [2].
When isolated (turning off the port of the other device via the switch
interface), both Ubiquiti devices doesn't see any other device with
batman neither have any client connected.
Both the devices independently (also when are isolated) print the same
error in dmesg:
br-lan: received packet on bat0 with own address as source address
This error is an indication that batman loop avoidance has some
problems, right?
Obviously loop avoidance is enabled.
# batctl bl
enabled
Various interfaces are bridged, for example in PicoStation I have:
# brctl show
bridge name bridge id STP enabled interfaces
br-lan 7fff.dc9fdb31c136 no eth0
bat0
wlan0_ap
I noticed that I'm not the first to ask here about this message [3][4].
I attach to this email dmesg form both isolated devices,
/etc/config/network, ip a, ifconfig, brctl and info from batctl.
Thanks,
Ilario
[1] http://libre-mesh.org/projects/libre-mesh
[2] https://github.com/ilario/configurazione-ilario-fisso
[3]
https://lists.open-mesh.org/pipermail/b.a.t.m.a.n/2012-February/006234.html
[4]
https://lists.open-mesh.org/pipermail/b.a.t.m.a.n/2013-October/010770.html
[-- Attachment #1.2: nano-batctl --]
[-- Type: text/plain, Size: 2371 bytes --]
root@ef8bda:~# batctl s
tx: 45
tx_bytes: 3399
tx_dropped: 7
rx: 26
rx_bytes: 1092
forward: 0
forward_bytes: 0
mgmt_tx: 775
mgmt_tx_bytes: 42138
mgmt_rx: 0
mgmt_rx_bytes: 0
frag_tx: 0
frag_tx_bytes: 0
frag_rx: 0
frag_rx_bytes: 0
frag_fwd: 0
frag_fwd_bytes: 0
tt_request_tx: 0
tt_request_rx: 0
tt_response_tx: 0
tt_response_rx: 0
tt_roam_adv_tx: 0
tt_roam_adv_rx: 0
dat_get_tx: 0
dat_get_rx: 0
dat_put_tx: 0
dat_put_rx: 0
dat_cached_reply_tx: 0
root@ef8bda:~# batctl if
eth0.11: active
eth1.11: active
root@ef8bda:~# batctl dat
disabled
root@ef8bda:~# batctl bl
enabled
root@ef8bda:~# batctl ap
disabled
root@ef8bda:~# batctl ag
enabled
root@ef8bda:~# batctl b
disabled
root@ef8bda:~# batctl f
enabled
root@ef8bda:~# batctl mark
0x00000000/0x00000000
root@ef8bda:~# batctl gw
off
root@ef8bda:~# batctl o
[B.A.T.M.A.N. adv 2014.1.0, MainIF/MAC: eth0.11/dc:9f:db:ef:8b:da (bat0 BATMAN_IV)]
Originator last-seen (#/255) Nexthop [outgoingIF]: Potential nexthops ...
No batman nodes in range ...
root@ef8bda:~# batctl gwl
Gateway (#/255) Nexthop [outgoingIF]: advertised uplink bandwidth ... [B.A.T.M.A.N. adv 2014.1.0, MainIF/MAC: eth0.11/dc:9f:db:ef:8b:da (bat0)]
No gateways in range ...
root@ef8bda:~# batctl tl
Locally retrieved addresses (from bat0) announced via TT (TTVN: 5):
Client VID Flags Last seen (CRC )
* 1e:d2:cb:8b:cb:24 0 [.P....] 0.000 (0xb7d000e8)
* 00:1e:8c:65:ef:0b -1 [......] 17.890 (0x514be548)
* 1e:d2:cb:8b:cb:24 -1 [.P....] 0.000 (0x514be548)
* 00:0c:42:ee:fe:e9 -1 [......] 34.960 (0x514be548)
* dc:9f:db:ef:8b:da -1 [......] 506.810 (0x514be548)
root@ef8bda:~# batctl tg
Globally announced TT entries received via the mesh bat0
Client VID (TTVN) Originator (Curr TTVN) (CRC ) Flags
root@ef8bda:~# batctl cl
Claims announced for the mesh bat0 (orig dc:9f:db:ef:8b:da, group id 0x3a6b)
Client VID Originator [o] (CRC )
root@ef8bda:~# batctl bbt
Backbones announced for the mesh bat0 (orig dc:9f:db:ef:8b:da, group id 0x3a6b)
Originator VID last seen (CRC )
root@ef8bda:~# batctl dc
Distributed ARP Table (bat0):
IPv4 MAC VID last-seen
[-- Attachment #1.3: nano-brctl --]
[-- Type: text/plain, Size: 155 bytes --]
root@ef8bda:~# brctl show
bridge name bridge id STP enabled interfaces
br-lan 7fff.dc9fdbef8bda no eth0
eth1
bat0
wlan0_ap
[-- Attachment #1.4: nano-dmesg --]
[-- Type: text/plain, Size: 15621 bytes --]
BusyBox v1.19.4 (2014-03-30 12:23:28 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r38505)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
___ __ __ _______ __
| |_|__| |--.----.-----. _ | | |-----.-----| |--.
| | | _ | _| -__||_|| | -__|__ --| |
|_____|__|_____|__| |_____| |__|_|__|_____|_____|__|__|
---------------------------------------------------------
(, rev.-)
---------------------------------------------------------
http://libre-mesh.org
---------------------------------------------------------
root@ef8bda:~# dmesg
[ 0.000000] Linux version 3.10.15 (ilario@ilario-fisso) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38505) ) #1 Sun Mar 30 12:34:05 CEST 2014
[ 0.000000] MyLoader: sysp=aaaaaaaa, boardp=aaaaa2aa, parts=aaaaaaaa
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7241 rev 1
[ 0.000000] Clocks: CPU:390.000MHz, DDR:390.000MHz, AHB:195.000MHz, Ref:5.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 8030aa90, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=UBNT-NM console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7552k(firmware),256k(cfg)ro,64k(EEPROM)ro rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 28784k/32768k available (2223k kernel code, 3984k reserved, 594k data, 252k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.060000] Calibrating delay loop... 259.27 BogoMIPS (lpj=1296384)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.080000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is Ubiquiti Nanostation M
[ 0.090000] registering PCI controller with io_map_base unset
[ 0.500000] bio: create slab <bio-0> at 0
[ 0.510000] PCI host bridge to bus 0000:00
[ 0.510000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.520000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.520000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.530000] pci 0000:00:00.0: [168c:002a] type 00 class 0x028000
[ 0.530000] pci 0000:00:00.0: fixup device configuration
[ 0.530000] pci 0000:00:00.0: reg 10: [mem 0x10000000-0x1000ffff 64bit]
[ 0.530000] pci 0000:00:00.0: supports D1
[ 0.530000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.530000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.530000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[ 0.540000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.540000] Switching to clocksource MIPS
[ 0.550000] NET: Registered protocol family 2
[ 0.550000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.560000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.570000] TCP: Hash tables configured (established 512 bind 512)
[ 0.570000] TCP: reno registered
[ 0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.580000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.590000] NET: Registered protocol family 1
[ 0.590000] PCI: CLS 0 bytes, default 32
[ 0.610000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.620000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.630000] msgmni has been set to 56
[ 0.630000] io scheduler noop registered
[ 0.640000] io scheduler deadline registered (default)
[ 0.640000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.670000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.680000] console [ttyS0] enabled, bootconsole disabled
[ 0.690000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.700000] m25p80 spi0.0: found s25fl064k, expected m25p80
[ 0.700000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[ 0.710000] 5 cmdlinepart partitions found on MTD device spi0.0
[ 0.710000] Creating 5 MTD partitions on "spi0.0":
[ 0.720000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.730000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.730000] 0x000000050000-0x0000007b0000 : "firmware"
[ 0.750000] 2 uimage-fw partitions found on MTD device firmware
[ 0.750000] 0x000000050000-0x00000014b37e : "kernel"
[ 0.760000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.770000] 0x00000014b37e-0x0000007b0000 : "rootfs"
[ 0.780000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.790000] mtd: partition "rootfs" set to be root filesystem
[ 0.800000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.810000] 0x0000003e0000-0x0000007b0000 : "rootfs_data"
[ 0.810000] 0x0000007b0000-0x0000007f0000 : "cfg"
[ 0.820000] 0x0000007f0000-0x000000800000 : "EEPROM"
[ 0.830000] libphy: ag71xx_mdio: probed
[ 0.840000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.400000] ag71xx ag71xx.0 eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 1.410000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 1.960000] eth1: Found an AR7240/AR9330 built-in switch
[ 3.000000] TCP: cubic registered
[ 3.000000] NET: Registered protocol family 17
[ 3.000000] Bridge firewalling registered
[ 3.010000] 8021q: 802.1Q VLAN Support v1.8
[ 3.020000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 3.030000] Freeing unused kernel memory: 252K (80321000 - 80360000)
[ 6.150000] usbcore: registered new interface driver usbfs
[ 6.160000] usbcore: registered new interface driver hub
[ 6.170000] usbcore: registered new device driver usb
[ 6.180000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.180000] ehci-platform: EHCI generic platform driver
[ 6.200000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.430000] eth0: link up (100Mbps/Full duplex)
[ 9.720000] jffs2: notice: (295) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 25 of xref (0 dead, 9 orphan) found.
[ 9.750000] eth0: link down
[ 11.980000] NET: Registered protocol family 10
[ 12.000000] tun: Universal TUN/TAP device driver, 1.6
[ 12.000000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 12.030000] nf_conntrack version 0.5.0 (453 buckets, 1812 max)
[ 12.040000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.100000] batman_adv: B.A.T.M.A.N. advanced 2014.1.0 (compatibility version 15) loaded
[ 12.160000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[ 12.160000] Backport generated by backports.git backports-20130617-4-ge3220f5
[ 12.200000] Ebtables v2.0 registered
[ 12.220000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.280000] xt_time: kernel timezone is -0000
[ 12.460000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.470000] cfg80211: World regulatory domain updated:
[ 12.480000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.480000] cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 12.490000] cfg80211: (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 12.560000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 12.570000] ath: EEPROM regdomain: 0x0
[ 12.570000] ath: EEPROM indicates default country code should be used
[ 12.570000] ath: doing EEPROM country->regdmn map search
[ 12.570000] ath: country maps to regdmn code: 0x3a
[ 12.570000] ath: Country alpha2 being used: US
[ 12.570000] ath: Regpair used: 0x3a
[ 12.590000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 12.600000] cfg80211: Calling CRDA for country: US
[ 12.600000] cfg80211: Regulatory domain changed to country: US
[ 12.610000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.620000] cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 12.630000] cfg80211: (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 12.630000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
[ 17.010000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 17.010000] device eth0 entered promiscuous mode
[ 17.040000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 17.180000] device br-lan entered promiscuous mode
[ 17.180000] IPv6: ADDRCONF(NETDEV_UP): anygw: link is not ready
[ 18.240000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 18.240000] device eth1 entered promiscuous mode
[ 18.250000] br-lan: port 2(eth1) entered forwarding state
[ 18.250000] br-lan: port 2(eth1) entered forwarding state
[ 18.260000] br-lan: port 2(eth1) entered disabled state
[ 18.270000] IPv6: ADDRCONF(NETDEV_UP): eth0.11: link is not ready
[ 18.300000] IPv6: ADDRCONF(NETDEV_UP): eth0.12: link is not ready
[ 18.350000] IPv6: ADDRCONF(NETDEV_UP): eth1.11: link is not ready
[ 18.410000] IPv6: ADDRCONF(NETDEV_UP): eth1.12: link is not ready
[ 18.590000] batman_adv: bat0: Adding interface: eth0.11
[ 18.590000] batman_adv: bat0: The MTU of interface eth0.11 is too small (1496) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1532 would solve the problem.
[ 18.620000] batman_adv: bat0: Interface activated: eth0.11
[ 18.660000] 8021q: adding VLAN 0 to HW filter on device bat0
[ 18.660000] device bat0 entered promiscuous mode
[ 18.670000] br-lan: port 3(bat0) entered forwarding state
[ 18.670000] br-lan: port 3(bat0) entered forwarding state
[ 18.680000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 18.710000] br-lan: received packet on bat0 with own address as source address
[ 18.730000] IPv6: ADDRCONF(NETDEV_CHANGE): anygw: link becomes ready
[ 18.810000] batman_adv: bat0: Adding interface: eth1.11
[ 18.820000] batman_adv: bat0: The MTU of interface eth1.11 is too small (1496) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1532 would solve the problem.
[ 18.840000] batman_adv: bat0: Interface activated: eth1.11
[ 19.910000] eth0: link up (100Mbps/Full duplex)
[ 19.950000] br-lan: port 1(eth0) entered forwarding state
[ 19.950000] br-lan: port 1(eth0) entered forwarding state
[ 19.960000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 19.980000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.11: link becomes ready
[ 19.980000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.12: link becomes ready
[ 20.450000] batman_adv: bat0: bridge_loop_avoidance: Changing from: disabled to: enabled
[ 20.480000] batman_adv: bat0: distributed_arp_table: Changing from: enabled to: disabled
[ 20.670000] br-lan: port 3(bat0) entered forwarding state
[ 21.950000] br-lan: port 1(eth0) entered forwarding state
[ 22.480000] IPv6: ADDRCONF(NETDEV_UP): wlan0_ap: link is not ready
[ 22.520000] IPv6: ADDRCONF(NETDEV_UP): wlan0_ap.12: link is not ready
[ 27.770000] device wlan0_ap entered promiscuous mode
[ 27.790000] IPv6: ADDRCONF(NETDEV_UP): wlan0_ap.12: link is not ready
[ 27.800000] IPv6: ADDRCONF(NETDEV_UP): wlan0_ap: link is not ready
[ 27.830000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0_ap: link becomes ready
[ 27.830000] br-lan: port 4(wlan0_ap) entered forwarding state
[ 27.840000] br-lan: port 4(wlan0_ap) entered forwarding state
[ 27.850000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0_ap.12: link becomes ready
[ 28.600000] br-lan: received packet on bat0 with own address as source address
[ 29.840000] br-lan: port 4(wlan0_ap) entered forwarding state
[ 31.900000] IPv6: ADDRCONF(NETDEV_UP): wlan0_adhoc: link is not ready
[ 31.920000] wlan0_adhoc: Created IBSS using preconfigured BSSID ca:fe:00:c0:ff:ee
[ 31.920000] wlan0_adhoc: Creating new IBSS network, BSSID ca:fe:00:c0:ff:ee
[ 31.930000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0_adhoc: link becomes ready
[ 38.620000] br-lan: received packet on bat0 with own address as source address
[ 48.640000] br-lan: received packet on bat0 with own address as source address
[ 58.660000] br-lan: received packet on bat0 with own address as source address
[ 68.680000] br-lan: received packet on bat0 with own address as source address
[ 78.700000] br-lan: received packet on bat0 with own address as source address
[ 88.720000] br-lan: received packet on bat0 with own address as source address
[ 98.740000] br-lan: received packet on bat0 with own address as source address
[ 108.760000] br-lan: received packet on bat0 with own address as source address
[ 118.780000] br-lan: received packet on bat0 with own address as source address
[ 128.800000] br-lan: received packet on bat0 with own address as source address
[ 138.820000] br-lan: received packet on bat0 with own address as source address
[ 148.840000] br-lan: received packet on bat0 with own address as source address
[ 158.860000] br-lan: received packet on bat0 with own address as source address
[ 168.880000] br-lan: received packet on bat0 with own address as source address
[-- Attachment #1.5: nano-etc-config-network --]
[-- Type: text/plain, Size: 1990 bytes --]
root@ef8bda:/etc/config# cat network
config interface 'loopback'
option ifname 'lo'
option proto 'static'
option ipaddr '127.0.0.1'
option netmask '255.0.0.0'
config globals 'globals'
config interface 'lan'
option type 'bridge'
option proto 'static'
option netmask '255.255.255.0'
option ip6assign '60'
option ip6addr '2001:DB8:0:0:0:0:0:8BDA/64'
option ipaddr '192.0.2.218'
option mtu '1500'
list ifname 'bat0'
list ifname 'eth0'
list ifname 'eth1'
list ifname 'wlan0_ap'
config interface 'wan'
option ifname 'eth1'
option proto 'dhcp'
config interface 'wan6'
option ifname '@wan'
option proto 'dhcpv6'
config device 'lm_anygw_dev'
option type 'macvlan'
option name 'anygw'
option ifname '@lan'
option macaddr 'aa:aa:aa:8a:15:ad'
config interface 'lm_anygw_if'
option proto 'static'
option ifname 'anygw'
option ip6addr '2001:DB8:0:0:0:0:0:1/64'
option ipaddr '192.0.2.1'
option netmask '255.255.255.0'
config interface 'lm_eth0_batadv'
option ifname 'eth0.11'
option proto 'batadv'
option mesh 'bat0'
option mtu '1496'
config interface 'lm_eth0_bmx6'
option ifname 'eth0.12'
option proto 'none'
option auto '1'
option mtu '1398'
config interface 'lm_eth1_batadv'
option ifname 'eth1.11'
option proto 'batadv'
option mesh 'bat0'
option mtu '1496'
config interface 'lm_eth1_bmx6'
option ifname 'eth1.12'
option proto 'none'
option auto '1'
option mtu '1398'
config interface 'lm_wlan0_ap_bmx6'
option ifname 'wlan0_ap.12'
option proto 'none'
option auto '1'
option mtu '1398'
config interface 'lm_wlan0_adhoc'
option proto 'none'
option mtu '1536'
option auto '1'
config interface 'lm_wlan0_adhoc_batadv'
option ifname '@lm_wlan0_adhoc.11'
option proto 'batadv'
option mesh 'bat0'
option mtu '1532'
config interface 'lm_wlan0_adhoc_bmx6'
option ifname 'wlan0_adhoc.12'
option proto 'none'
option auto '1'
option mtu '1398'
[-- Attachment #1.6: nano-ifconfig --]
[-- Type: text/plain, Size: 6520 bytes --]
root@ef8bda:~# ifconfig
anygw Link encap:Ethernet HWaddr AA:AA:AA:8A:15:AD
inet addr:192.0.2.1 Bcast:192.0.2.255 Mask:255.255.255.0
inet6 addr: 2001:db8::1/64 Scope:Global
inet6 addr: fe80::a8aa:aaff:fe8a:15ad/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:113 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:6348 (6.1 KiB) TX bytes:596 (596.0 B)
bat0 Link encap:Ethernet HWaddr 1E:D2:CB:8B:CB:24
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:48 errors:0 dropped:0 overruns:0 frame:0
TX packets:72 errors:0 dropped:7 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2016 (1.9 KiB) TX bytes:5180 (5.0 KiB)
bmxmain Link encap:UNSPEC HWaddr FD-66-00-66-00-66-00-09-00-00-00-00-00-00-00-00
inet addr:192.0.2.218 P-t-P:192.0.2.218 Mask:255.255.255.255
inet6 addr: 2001:db8::8bda/128 Scope:Global
inet6 addr: fe80::de9f:dbff:feef:8bda/64 Scope:Link
UP POINTOPOINT RUNNING NOARP MTU:1452 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
br-lan Link encap:Ethernet HWaddr DC:9F:DB:EF:8B:DA
inet addr:192.0.2.218 Bcast:192.0.2.255 Mask:255.255.255.0
inet6 addr: 2001:db8::8bda/64 Scope:Global
inet6 addr: fe80::de9f:dbff:feef:8bda/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:263 errors:0 dropped:0 overruns:0 frame:0
TX packets:130 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:21626 (21.1 KiB) TX bytes:38290 (37.3 KiB)
eth0 Link encap:Ethernet HWaddr DC:9F:DB:EF:8B:DA
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:215 errors:0 dropped:0 overruns:0 frame:0
TX packets:1532 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:23292 (22.7 KiB) TX bytes:149303 (145.8 KiB)
Interrupt:4
eth0.11 Link encap:Ethernet HWaddr DC:9F:DB:EF:8B:DA
inet6 addr: fe80::de9f:dbff:feef:8bda/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1496 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:536 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:35632 (34.7 KiB)
eth0.12 Link encap:Ethernet HWaddr DC:9F:DB:EF:8B:DA
inet6 addr: fd66:66:66:9:de9f:dbff:feef:8bda/64 Scope:Global
inet6 addr: fe80::de9f:dbff:feef:8bda/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1398 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:828 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:68893 (67.2 KiB)
eth1 Link encap:Ethernet HWaddr DE:9F:DB:EF:8B:DA
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:5
eth1.11 Link encap:Ethernet HWaddr DE:9F:DB:EF:8B:DA
UP BROADCAST MULTICAST MTU:1496 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth1.12 Link encap:Ethernet HWaddr DE:9F:DB:EF:8B:DA
inet6 addr: fd66:66:66:b:de9f:dbff:feef:8bda/64 Scope:Global
UP BROADCAST MULTICAST MTU:1398 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:3312 errors:0 dropped:0 overruns:0 frame:0
TX packets:3312 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:225216 (219.9 KiB) TX bytes:225216 (219.9 KiB)
wlan0_adhoc Link encap:Ethernet HWaddr DE:9F:DB:EE:8B:DA
inet6 addr: fe80::dc9f:dbff:feee:8bda/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:833 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:87677 (85.6 KiB)
wlan0_adhoc.12 Link encap:Ethernet HWaddr DE:9F:DB:EE:8B:DA
inet6 addr: fd66:66:66:10:de9f:dbff:feee:8bda/64 Scope:Global
inet6 addr: fe80::dc9f:dbff:feee:8bda/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:828 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:68893 (67.2 KiB)
wlan0_ap Link encap:Ethernet HWaddr DC:9F:DB:EE:8B:DA
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:941 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:95868 (93.6 KiB)
wlan0_ap.12 Link encap:Ethernet HWaddr DC:9F:DB:EE:8B:DA
inet6 addr: fd66:66:66:e:de9f:dbff:feee:8bda/64 Scope:Global
inet6 addr: fe80::de9f:dbff:feee:8bda/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:828 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:68893 (67.2 KiB)
[-- Attachment #1.7: nano-ip_a --]
[-- Type: text/plain, Size: 4593 bytes --]
root@ef8bda:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel master br-lan state UP group default qlen 1000
link/ether dc:9f:db:ef:8b:da brd ff:ff:ff:ff:ff:ff
3: eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel master br-lan state DOWN group default qlen 1000
link/ether de:9f:db:ef:8b:da brd ff:ff:ff:ff:ff:ff
4: ip6tnl0: <NOARP> mtu 1452 qdisc noop state DOWN group default
link/tunnel6 :: brd ::
6: br-lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
link/ether dc:9f:db:ef:8b:da brd ff:ff:ff:ff:ff:ff
inet 192.0.2.218/24 brd 192.0.2.255 scope global br-lan
valid_lft forever preferred_lft forever
inet6 2001:db8::8bda/64 scope global
valid_lft forever preferred_lft forever
inet6 fe80::de9f:dbff:feef:8bda/64 scope link
valid_lft forever preferred_lft forever
7: anygw@br-lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
link/ether aa:aa:aa:8a:15:ad brd ff:ff:ff:ff:ff:ff
inet 192.0.2.1/24 brd 192.0.2.255 scope global anygw
valid_lft forever preferred_lft forever
inet6 2001:db8::1/64 scope global
valid_lft forever preferred_lft forever
inet6 fe80::a8aa:aaff:fe8a:15ad/64 scope link
valid_lft forever preferred_lft forever
8: eth0.11@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1496 qdisc noqueue master bat0 state UP group default
link/ether dc:9f:db:ef:8b:da brd ff:ff:ff:ff:ff:ff
inet6 fe80::de9f:dbff:feef:8bda/64 scope link
valid_lft forever preferred_lft forever
9: eth0.12@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1398 qdisc noqueue state UP group default
link/ether dc:9f:db:ef:8b:da brd ff:ff:ff:ff:ff:ff
inet6 fd66:66:66:9:de9f:dbff:feef:8bda/64 scope global
valid_lft forever preferred_lft forever
inet6 fe80::de9f:dbff:feef:8bda/64 scope link
valid_lft forever preferred_lft forever
10: eth1.11@eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1496 qdisc noqueue master bat0 state LOWERLAYERDOWN group default
link/ether de:9f:db:ef:8b:da brd ff:ff:ff:ff:ff:ff
11: eth1.12@eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1398 qdisc noqueue state LOWERLAYERDOWN group default
link/ether de:9f:db:ef:8b:da brd ff:ff:ff:ff:ff:ff
inet6 fd66:66:66:b:de9f:dbff:feef:8bda/64 scope global tentative
valid_lft forever preferred_lft forever
12: bat0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master br-lan state UNKNOWN group default
link/ether 1e:d2:cb:8b:cb:24 brd ff:ff:ff:ff:ff:ff
13: wlan0_ap: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master br-lan state UP group default qlen 1000
link/ether dc:9f:db:ee:8b:da brd ff:ff:ff:ff:ff:ff
14: wlan0_ap.12@wlan0_ap: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
link/ether dc:9f:db:ee:8b:da brd ff:ff:ff:ff:ff:ff
inet6 fd66:66:66:e:de9f:dbff:feee:8bda/64 scope global
valid_lft forever preferred_lft forever
inet6 fe80::de9f:dbff:feee:8bda/64 scope link
valid_lft forever preferred_lft forever
15: wlan0_adhoc: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1536 qdisc mq state UP group default qlen 1000
link/ether de:9f:db:ee:8b:da brd ff:ff:ff:ff:ff:ff
inet6 fe80::dc9f:dbff:feee:8bda/64 scope link
valid_lft forever preferred_lft forever
16: wlan0_adhoc.12@wlan0_adhoc: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
link/ether de:9f:db:ee:8b:da brd ff:ff:ff:ff:ff:ff
inet6 fd66:66:66:10:de9f:dbff:feee:8bda/64 scope global
valid_lft forever preferred_lft forever
inet6 fe80::dc9f:dbff:feee:8bda/64 scope link
valid_lft forever preferred_lft forever
17: bmxmain: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1452 qdisc noqueue state UNKNOWN group default
link/tunnel6 fd66:66:66:9:de9f:dbff:feef:8bda peer fd66:66:66:ff00:de9f:dbff:feef:8bda
inet 192.0.2.218/32 scope global bmxmain
valid_lft forever preferred_lft forever
inet6 2001:db8::8bda/128 scope global
valid_lft forever preferred_lft forever
inet6 fe80::de9f:dbff:feef:8bda/64 scope link
valid_lft forever preferred_lft forever
[-- Attachment #1.8: pico-batctl --]
[-- Type: text/plain, Size: 2463 bytes --]
root@31c136:~# batctl s
tx: 25
tx_bytes: 1872
tx_dropped: 12
rx: 15
rx_bytes: 630
forward: 0
forward_bytes: 0
mgmt_tx: 139
mgmt_tx_bytes: 8870
mgmt_rx: 0
mgmt_rx_bytes: 0
frag_tx: 0
frag_tx_bytes: 0
frag_rx: 0
frag_rx_bytes: 0
frag_fwd: 0
frag_fwd_bytes: 0
tt_request_tx: 0
tt_request_rx: 0
tt_response_tx: 0
tt_response_rx: 0
tt_roam_adv_tx: 0
tt_roam_adv_rx: 0
dat_get_tx: 0
dat_get_rx: 0
dat_put_tx: 0
dat_put_rx: 0
dat_cached_reply_tx: 0
root@31c136:~# batctl if
eth0.11: active
root@31c136:~# batctl dat
disabled
root@31c136:~# batctl bl
enabled
root@31c136:~# batctl ap
disabled
root@31c136:~# batctl ag
enabled
root@31c136:~# batctl b
disabled
root@31c136:~# batctl f
enabled
root@31c136:~# batctl mark
0x00000000/0x00000000
root@31c136:~# batctl gw
off
root@31c136:~# batctl o
[B.A.T.M.A.N. adv 2014.1.0, MainIF/MAC: eth0.11/dc:9f:db:31:c1:36 (bat0 BATMAN_IV)]
Originator last-seen (#/255) Nexthop [outgoingIF]: Potential nexthops ...
No batman nodes in range ...
root@31c136:~# batctl gwl
Gateway (#/255) Nexthop [outgoingIF]: advertised uplink bandwidth ... [B.A.T.M.A.N. adv 2014.1.0, MainIF/MAC: eth0.11/dc:9f:db:31:c1:36 (bat0)]
No gateways in range ...
root@31c136:~# batctl tl
Locally retrieved addresses (from bat0) announced via TT (TTVN: 3):
Client VID Flags Last seen (CRC )
* dc:9f:db:31:c1:36 -1 [......] 219.070 (0xf61bea85)
* 00:1e:8c:65:ef:0b -1 [......] 8.760 (0xf61bea85)
* be:17:45:43:f2:e1 -1 [.P....] 0.000 (0xf61bea85)
* aa:aa:aa:8a:15:ad -1 [......] 218.710 (0xf61bea85)
* 00:0c:42:ee:fe:e9 -1 [......] 55.070 (0xf61bea85)
* be:17:45:43:f2:e1 0 [.P....] 0.000 (0x83bdc53d)
root@31c136:~# batctl tg
Globally announced TT entries received via the mesh bat0
Client VID (TTVN) Originator (Curr TTVN) (CRC ) Flags
root@31c136:~# batctl cl
Claims announced for the mesh bat0 (orig dc:9f:db:31:c1:36, group id 0xed3d)
Client VID Originator [o] (CRC )
root@31c136:~# batctl bbt
Backbones announced for the mesh bat0 (orig dc:9f:db:31:c1:36, group id 0xed3d)
Originator VID last seen (CRC )
root@31c136:~# batctl dc
Distributed ARP Table (bat0):
IPv4 MAC VID last-seen
* 10.37.133.1 00:1e:8c:65:ef:0b -1 4:07
[-- Attachment #1.9: pico-brctl --]
[-- Type: text/plain, Size: 140 bytes --]
root@31c136:~# brctl show
bridge name bridge id STP enabled interfaces
br-lan 7fff.dc9fdb31c136 no eth0
bat0
wlan0_ap
[-- Attachment #1.10: pico-dmesg --]
[-- Type: text/plain, Size: 13058 bytes --]
root@31c136:~# dmesg
[ 0.000000] Linux version 3.10.15 (ilario@ilario-fisso) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38505) ) #1 Sun Mar 30 12:34:05 CEST 2014
[ 0.000000] MyLoader: sysp=d7bf7fa7, boardp=5fe05eaf, parts=57ed58e6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7241 rev 1
[ 0.000000] Clocks: CPU:390.000MHz, DDR:390.000MHz, AHB:195.000MHz, Ref:5.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 8030aa90, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=UBNT-BM console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7552k(firmware),256k(cfg)ro,64k(EEPROM)ro rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 28784k/32768k available (2223k kernel code, 3984k reserved, 594k data, 252k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.060000] Calibrating delay loop... 259.27 BogoMIPS (lpj=1296384)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.080000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is Ubiquiti Bullet M
[ 0.090000] registering PCI controller with io_map_base unset
[ 0.300000] bio: create slab <bio-0> at 0
[ 0.310000] PCI host bridge to bus 0000:00
[ 0.310000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.320000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.320000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.330000] pci 0000:00:00.0: [168c:002a] type 00 class 0x028000
[ 0.330000] pci 0000:00:00.0: fixup device configuration
[ 0.330000] pci 0000:00:00.0: reg 10: [mem 0x10000000-0x1000ffff 64bit]
[ 0.330000] pci 0000:00:00.0: supports D1
[ 0.330000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.330000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.330000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[ 0.340000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.340000] Switching to clocksource MIPS
[ 0.350000] NET: Registered protocol family 2
[ 0.350000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.360000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.370000] TCP: Hash tables configured (established 512 bind 512)
[ 0.370000] TCP: reno registered
[ 0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.390000] NET: Registered protocol family 1
[ 0.390000] PCI: CLS 0 bytes, default 32
[ 0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.420000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.430000] msgmni has been set to 56
[ 0.430000] io scheduler noop registered
[ 0.440000] io scheduler deadline registered (default)
[ 0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.470000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.480000] console [ttyS0] enabled, bootconsole disabled
[ 0.490000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.500000] m25p80 spi0.0: found s25fl064k, expected m25p80
[ 0.500000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[ 0.510000] 5 cmdlinepart partitions found on MTD device spi0.0
[ 0.510000] Creating 5 MTD partitions on "spi0.0":
[ 0.520000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.530000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.530000] 0x000000050000-0x0000007b0000 : "firmware"
[ 0.550000] 2 uimage-fw partitions found on MTD device firmware
[ 0.550000] 0x000000050000-0x00000014b34a : "kernel"
[ 0.560000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.570000] 0x00000014b34a-0x0000007b0000 : "rootfs"
[ 0.580000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.590000] mtd: partition "rootfs" set to be root filesystem
[ 0.600000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.610000] 0x0000003e0000-0x0000007b0000 : "rootfs_data"
[ 0.610000] 0x0000007b0000-0x0000007f0000 : "cfg"
[ 0.620000] 0x0000007f0000-0x000000800000 : "EEPROM"
[ 0.630000] libphy: ag71xx_mdio: probed
[ 0.640000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.200000] ag71xx ag71xx.0 eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 1.210000] TCP: cubic registered
[ 1.210000] NET: Registered protocol family 17
[ 1.220000] Bridge firewalling registered
[ 1.220000] 8021q: 802.1Q VLAN Support v1.8
[ 1.230000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.240000] Freeing unused kernel memory: 252K (80321000 - 80360000)
[ 4.370000] usbcore: registered new interface driver usbfs
[ 4.370000] usbcore: registered new interface driver hub
[ 4.380000] usbcore: registered new device driver usb
[ 4.390000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.400000] ehci-platform: EHCI generic platform driver
[ 4.410000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 7.240000] eth0: link up (100Mbps/Full duplex)
[ 7.930000] jffs2: notice: (292) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 24 of xref (0 dead, 8 orphan) found.
[ 7.960000] eth0: link down
[ 10.220000] NET: Registered protocol family 10
[ 10.230000] tun: Universal TUN/TAP device driver, 1.6
[ 10.240000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 10.270000] nf_conntrack version 0.5.0 (453 buckets, 1812 max)
[ 10.290000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.350000] batman_adv: B.A.T.M.A.N. advanced 2014.1.0 (compatibility version 15) loaded
[ 10.390000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[ 10.400000] Backport generated by backports.git backports-20130617-4-ge3220f5
[ 10.440000] Ebtables v2.0 registered
[ 10.460000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.650000] xt_time: kernel timezone is -0000
[ 10.770000] cfg80211: Calling CRDA to update world regulatory domain
[ 10.770000] cfg80211: World regulatory domain updated:
[ 10.780000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 10.790000] cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 10.790000] cfg80211: (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 10.850000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 10.860000] ath: EEPROM regdomain: 0x0
[ 10.860000] ath: EEPROM indicates default country code should be used
[ 10.860000] ath: doing EEPROM country->regdmn map search
[ 10.860000] ath: country maps to regdmn code: 0x3a
[ 10.860000] ath: Country alpha2 being used: US
[ 10.860000] ath: Regpair used: 0x3a
[ 10.880000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 10.880000] cfg80211: Calling CRDA for country: US
[ 10.890000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
[ 10.900000] cfg80211: Regulatory domain changed to country: US
[ 10.900000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 10.910000] cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 10.920000] cfg80211: (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 15.790000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 15.790000] device eth0 entered promiscuous mode
[ 15.800000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 15.830000] device br-lan entered promiscuous mode
[ 15.840000] IPv6: ADDRCONF(NETDEV_UP): anygw: link is not ready
[ 15.910000] IPv6: ADDRCONF(NETDEV_UP): eth0.11: link is not ready
[ 15.950000] IPv6: ADDRCONF(NETDEV_UP): eth0.12: link is not ready
[ 16.210000] batman_adv: bat0: Adding interface: eth0.11
[ 16.220000] batman_adv: bat0: The MTU of interface eth0.11 is too small (1496) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1532 would solve the problem.
[ 16.240000] batman_adv: bat0: Interface activated: eth0.11
[ 16.250000] 8021q: adding VLAN 0 to HW filter on device bat0
[ 16.290000] device bat0 entered promiscuous mode
[ 16.290000] br-lan: port 2(bat0) entered forwarding state
[ 16.300000] br-lan: port 2(bat0) entered forwarding state
[ 16.300000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 16.340000] IPv6: ADDRCONF(NETDEV_CHANGE): anygw: link becomes ready
[ 16.400000] eth0: link up (100Mbps/Full duplex)
[ 16.400000] br-lan: port 1(eth0) entered forwarding state
[ 16.410000] br-lan: port 1(eth0) entered forwarding state
[ 16.410000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 16.440000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.11: link becomes ready
[ 16.440000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.12: link becomes ready
[ 17.360000] batman_adv: bat0: bridge_loop_avoidance: Changing from: disabled to: enabled
[ 17.400000] batman_adv: bat0: distributed_arp_table: Changing from: enabled to: disabled
[ 18.300000] br-lan: port 2(bat0) entered forwarding state
[ 18.410000] br-lan: port 1(eth0) entered forwarding state
[ 21.330000] IPv6: ADDRCONF(NETDEV_UP): wlan0_ap: link is not ready
[ 21.330000] IPv6: ADDRCONF(NETDEV_UP): wlan0_ap.12: link is not ready
[ 26.240000] br-lan: received packet on bat0 with own address as source address
[ 29.270000] device wlan0_ap entered promiscuous mode
[ 29.310000] IPv6: ADDRCONF(NETDEV_UP): wlan0_ap.12: link is not ready
[ 29.310000] IPv6: ADDRCONF(NETDEV_UP): wlan0_ap: link is not ready
[ 29.330000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0_ap: link becomes ready
[ 29.360000] br-lan: port 3(wlan0_ap) entered forwarding state
[ 29.360000] br-lan: port 3(wlan0_ap) entered forwarding state
[ 29.380000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0_ap.12: link becomes ready
[ 31.360000] br-lan: port 3(wlan0_ap) entered forwarding state
[ 32.940000] device wlan0_adhoc entered promiscuous mode
[ 32.940000] IPv6: ADDRCONF(NETDEV_UP): wlan0_adhoc: link is not ready
[ 32.960000] wlan0_adhoc: Created IBSS using preconfigured BSSID ca:fe:00:c0:ff:ee
[ 32.970000] wlan0_adhoc: Creating new IBSS network, BSSID ca:fe:00:c0:ff:ee
[ 32.980000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0_adhoc: link becomes ready
[ 36.260000] br-lan: received packet on bat0 with own address as source address
[ 46.280000] br-lan: received packet on bat0 with own address as source address
[ 56.300000] br-lan: received packet on bat0 with own address as source address
[ 66.320000] br-lan: received packet on bat0 with own address as source address
[ 76.340000] br-lan: received packet on bat0 with own address as source address
[ 86.360000] br-lan: received packet on bat0 with own address as source address
[ 96.380000] br-lan: received packet on bat0 with own address as source address
[ 106.400000] br-lan: received packet on bat0 with own address as source address
[ 116.420000] br-lan: received packet on bat0 with own address as source address
[ 126.440000] br-lan: received packet on bat0 with own address as source address
[-- Attachment #1.11: pico-etc-config-network --]
[-- Type: text/plain, Size: 1578 bytes --]
root@31c136:~# cat /etc/config/network
config interface 'loopback'
option ifname 'lo'
option proto 'static'
option ipaddr '127.0.0.1'
option netmask '255.0.0.0'
config globals 'globals'
config interface 'lan'
option type 'bridge'
option proto 'static'
option netmask '255.255.255.0'
option ip6assign '60'
option ip6addr '2001:DB8:0:0:0:0:0:C136/64'
option ipaddr '192.0.2.54'
option mtu '1500'
list ifname 'bat0'
list ifname 'eth0'
list ifname 'wlan0_ap'
config device 'lm_anygw_dev'
option type 'macvlan'
option name 'anygw'
option ifname '@lan'
option macaddr 'aa:aa:aa:8a:15:ad'
config interface 'lm_anygw_if'
option proto 'static'
option ifname 'anygw'
option ip6addr '2001:DB8:0:0:0:0:0:1/64'
option ipaddr '192.0.2.1'
option netmask '255.255.255.0'
config interface 'lm_eth0_batadv'
option ifname 'eth0.11'
option proto 'batadv'
option mesh 'bat0'
option mtu '1496'
config interface 'lm_eth0_bmx6'
option ifname 'eth0.12'
option proto 'none'
option auto '1'
option mtu '1398'
config interface 'lm_wlan0_ap_bmx6'
option ifname 'wlan0_ap.12'
option proto 'none'
option auto '1'
option mtu '1398'
config interface 'lm_wlan0_adhoc'
option proto 'none'
option mtu '1536'
option auto '1'
config interface 'lm_wlan0_adhoc_batadv'
option ifname '@lm_wlan0_adhoc.11'
option proto 'batadv'
option mesh 'bat0'
option mtu '1532'
config interface 'lm_wlan0_adhoc_bmx6'
option ifname 'wlan0_adhoc.12'
option proto 'none'
option auto '1'
option mtu '1398'
[-- Attachment #1.12: pico-ifconfig --]
[-- Type: text/plain, Size: 4637 bytes --]
root@31c136:~# ifconfig
anygw Link encap:Ethernet HWaddr AA:AA:AA:8A:15:AD
inet addr:192.0.2.1 Bcast:192.0.2.255 Mask:255.255.255.0
inet6 addr: 2001:db8::1/64 Scope:Global
inet6 addr: fe80::a8aa:aaff:fe8a:15ad/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:85 errors:0 dropped:0 overruns:0 frame:0
TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4799 (4.6 KiB) TX bytes:526 (526.0 B)
bat0 Link encap:Ethernet HWaddr BE:17:45:43:F2:E1
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:33 errors:0 dropped:0 overruns:0 frame:0
TX packets:55 errors:0 dropped:12 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1386 (1.3 KiB) TX bytes:3837 (3.7 KiB)
br-lan Link encap:Ethernet HWaddr DC:9F:DB:31:C1:36
inet addr:192.0.2.54 Bcast:192.0.2.255 Mask:255.255.255.0
inet6 addr: fe80::de9f:dbff:fe31:c136/64 Scope:Link
inet6 addr: 2001:db8::c136/64 Scope:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:496 errors:0 dropped:0 overruns:0 frame:0
TX packets:307 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:47337 (46.2 KiB) TX bytes:78580 (76.7 KiB)
eth0 Link encap:Ethernet HWaddr DC:9F:DB:31:C1:36
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:464 errors:0 dropped:0 overruns:0 frame:0
TX packets:719 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:52937 (51.6 KiB) TX bytes:107147 (104.6 KiB)
Interrupt:4
eth0.11 Link encap:Ethernet HWaddr DC:9F:DB:31:C1:36
inet6 addr: fe80::de9f:dbff:fe31:c136/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1496 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:378 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:25547 (24.9 KiB)
eth0.12 Link encap:Ethernet HWaddr DC:9F:DB:31:C1:36
inet6 addr: fe80::de9f:dbff:fe31:c136/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1398 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:408 (408.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:2112 errors:0 dropped:0 overruns:0 frame:0
TX packets:2112 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:143616 (140.2 KiB) TX bytes:143616 (140.2 KiB)
wlan0_adhoc Link encap:Ethernet HWaddr DE:9F:DB:30:C1:36
inet6 addr: fe80::dc9f:dbff:fe30:c136/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:844 (844.0 B)
wlan0_adhoc.12 Link encap:Ethernet HWaddr DC:9F:DB:30:C1:36
inet6 addr: fe80::de9f:dbff:fe30:c136/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:298 (298.0 B)
wlan0_ap Link encap:Ethernet HWaddr DC:9F:DB:30:C1:36
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:83 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:6389 (6.2 KiB)
wlan0_ap.12 Link encap:Ethernet HWaddr DC:9F:DB:30:C1:36
inet6 addr: fe80::de9f:dbff:fe30:c136/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:478 (478.0 B)
[-- Attachment #1.13: pico-ip_a --]
[-- Type: text/plain, Size: 3143 bytes --]
root@31c136:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel master br-lan state UP group default qlen 1000
link/ether dc:9f:db:31:c1:36 brd ff:ff:ff:ff:ff:ff
3: ip6tnl0: <NOARP> mtu 1452 qdisc noop state DOWN group default
link/tunnel6 :: brd ::
5: br-lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
link/ether dc:9f:db:31:c1:36 brd ff:ff:ff:ff:ff:ff
inet 192.0.2.54/24 brd 192.0.2.255 scope global br-lan
valid_lft forever preferred_lft forever
inet6 2001:db8::c136/64 scope global
valid_lft forever preferred_lft forever
inet6 fe80::de9f:dbff:fe31:c136/64 scope link
valid_lft forever preferred_lft forever
6: anygw@br-lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
link/ether aa:aa:aa:8a:15:ad brd ff:ff:ff:ff:ff:ff
inet 192.0.2.1/24 brd 192.0.2.255 scope global anygw
valid_lft forever preferred_lft forever
inet6 2001:db8::1/64 scope global
valid_lft forever preferred_lft forever
inet6 fe80::a8aa:aaff:fe8a:15ad/64 scope link
valid_lft forever preferred_lft forever
7: eth0.11@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1496 qdisc noqueue master bat0 state UP group default
link/ether dc:9f:db:31:c1:36 brd ff:ff:ff:ff:ff:ff
inet6 fe80::de9f:dbff:fe31:c136/64 scope link
valid_lft forever preferred_lft forever
8: eth0.12@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1398 qdisc noqueue state UP group default
link/ether dc:9f:db:31:c1:36 brd ff:ff:ff:ff:ff:ff
inet6 fe80::de9f:dbff:fe31:c136/64 scope link
valid_lft forever preferred_lft forever
9: bat0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master br-lan state UNKNOWN group default
link/ether be:17:45:43:f2:e1 brd ff:ff:ff:ff:ff:ff
10: wlan0_ap: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master br-lan state UP group default qlen 1000
link/ether dc:9f:db:30:c1:36 brd ff:ff:ff:ff:ff:ff
11: wlan0_ap.12@wlan0_ap: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
link/ether dc:9f:db:30:c1:36 brd ff:ff:ff:ff:ff:ff
inet6 fe80::de9f:dbff:fe30:c136/64 scope link
valid_lft forever preferred_lft forever
12: wlan0_adhoc: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1536 qdisc mq state UP group default qlen 1000
link/ether de:9f:db:30:c1:36 brd ff:ff:ff:ff:ff:ff
inet6 fe80::dc9f:dbff:fe30:c136/64 scope link
valid_lft forever preferred_lft forever
13: wlan0_adhoc.12@wlan0_adhoc: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
link/ether dc:9f:db:30:c1:36 brd ff:ff:ff:ff:ff:ff
inet6 fe80::de9f:dbff:fe30:c136/64 scope link
valid_lft forever preferred_lft forever
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 246 bytes --]
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [B.A.T.M.A.N.] br-lan: received packet on bat0 with own address as source address
2014-03-31 20:10 [B.A.T.M.A.N.] br-lan: received packet on bat0 with own address as source address Ilario Gelmetti
@ 2014-04-01 9:33 ` Ilario GELMETTI
2014-04-01 10:35 ` Gioacchino Mazzurco
0 siblings, 1 reply; 4+ messages in thread
From: Ilario GELMETTI @ 2014-04-01 9:33 UTC (permalink / raw)
To: b.a.t.m.a.n
On Mon, 31 Mar 2014 22:10:37 +0200
Ilario Gelmetti <ilario.gelmetti@sns.it> wrote:
> I have two devices (Ubiquiti PicoStation M2 and Ubiquiti NanoStation M5)
> mounted on the same pole both running libre-mesh [1] firmware
> (batman-adv: 2014.1.0) and both attached to a Mikrotik RB250GS gigabit
> switch (latest 1.11 firmware, default configuration)
> ...
> Both the devices independently (also when are isolated) print the same
> error in dmesg:
> br-lan: received packet on bat0 with own address as source address
On libre-mesh mailing list there's a solution suggesting to change a mac addresses:
http://lists.libre-mesh.org/pipermail/dev/2014-April/000316.html
I tried changing the mac address
config interface 'lm_eth0_batadv'
option ifname 'eth0.11'
option proto 'batadv'
option mesh 'bat0'
option mtu '1496'
option macaddr 'dc:9f:db:31:c1:38'
and that error in dmesg went away.
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [B.A.T.M.A.N.] br-lan: received packet on bat0 with own address as source address
2014-04-01 9:33 ` Ilario GELMETTI
@ 2014-04-01 10:35 ` Gioacchino Mazzurco
2014-04-01 12:09 ` Antonio Quartulli
0 siblings, 1 reply; 4+ messages in thread
From: Gioacchino Mazzurco @ 2014-04-01 10:35 UTC (permalink / raw)
To: b.a.t.m.a.n
On Tuesday 01 April 2014 11:33:01 Ilario GELMETTI wrote:
> I tried changing the mac address
> config interface 'lm_eth0_batadv'
> option ifname 'eth0.11'
> option proto 'batadv'
> option mesh 'bat0'
> option mtu '1496'
> option macaddr 'dc:9f:db:31:c1:38'
> and that error in dmesg went away.
Why a packet form eth0.11 should arrive periodically to the bridge ?
Someone can make some sense out of this ?
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [B.A.T.M.A.N.] br-lan: received packet on bat0 with own address as source address
2014-04-01 10:35 ` Gioacchino Mazzurco
@ 2014-04-01 12:09 ` Antonio Quartulli
0 siblings, 0 replies; 4+ messages in thread
From: Antonio Quartulli @ 2014-04-01 12:09 UTC (permalink / raw)
To: b.a.t.m.a.n
[-- Attachment #1: Type: text/plain, Size: 790 bytes --]
On 01/04/14 12:35, Gioacchino Mazzurco wrote:
> On Tuesday 01 April 2014 11:33:01 Ilario GELMETTI wrote:
>> I tried changing the mac address
>> config interface 'lm_eth0_batadv'
>> option ifname 'eth0.11'
>> option proto 'batadv'
>> option mesh 'bat0'
>> option mtu '1496'
>> option macaddr 'dc:9f:db:31:c1:38'
>> and that error in dmesg went away.
>
> Why a packet form eth0.11 should arrive periodically to the bridge ?
> Someone can make some sense out of this ?
>
I guess that the packet hits the bridge before being de-multiplexed by
the vlan code (or both the paths are followed till a certain point?).
We should dig into the bridge/vlan code to better understand what is
going on..
Cheers,
--
Antonio Quartulli
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 901 bytes --]
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2014-04-01 12:09 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-03-31 20:10 [B.A.T.M.A.N.] br-lan: received packet on bat0 with own address as source address Ilario Gelmetti
2014-04-01 9:33 ` Ilario GELMETTI
2014-04-01 10:35 ` Gioacchino Mazzurco
2014-04-01 12:09 ` Antonio Quartulli
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).