[PATCH v2 07/14] dt-bindings: dma: ti: Add document for K3 UDMA

[Peter Ujfalusi <peter.ujfalusi@ti.com>]

New binding document for
Texas Instruments K3 NAVSS Unified DMA – Peripheral Root Complex (UDMA-P).

UDMA-P is introduced as part of the K3 architecture and can be found on
AM654 and j721e.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
---
 .../devicetree/bindings/dma/ti/k3-udma.txt    | 170 ++++++++++++++++++
 include/dt-bindings/dma/k3-udma.h             |  10 ++
 2 files changed, 180 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/dma/ti/k3-udma.txt
 create mode 100644 include/dt-bindings/dma/k3-udma.h

diff --git a/Documentation/devicetree/bindings/dma/ti/k3-udma.txt b/Documentation/devicetree/bindings/dma/ti/k3-udma.txt
new file mode 100644
index 000000000000..7f30fe583ade
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/ti/k3-udma.txt
@@ -0,0 +1,170 @@
+* Texas Instruments K3 NAVSS Unified DMA – Peripheral Root Complex (UDMA-P)
+
+The UDMA-P is intended to perform similar (but significantly upgraded) functions
+as the packet-oriented DMA used on previous SoC devices. The UDMA-P module
+supports the transmission and reception of various packet types. The UDMA-P is
+architected to facilitate the segmentation and reassembly of SoC DMA data
+structure compliant packets to/from smaller data blocks that are natively
+compatible with the specific requirements of each connected peripheral. Multiple
+Tx and Rx channels are provided within the DMA which allow multiple segmentation
+or reassembly operations to be ongoing. The DMA controller maintains state
+information for each of the channels which allows packet segmentation and
+reassembly operations to be time division multiplexed between channels in order
+to share the underlying DMA hardware. An external DMA scheduler is used to
+control the ordering and rate at which this multiplexing occurs for Transmit
+operations. The ordering and rate of Receive operations is indirectly controlled
+by the order in which blocks are pushed into the DMA on the Rx PSI-L interface.
+
+The UDMA-P also supports acting as both a UTC and UDMA-C for its internal
+channels. Channels in the UDMA-P can be configured to be either Packet-Based or
+Third-Party channels on a channel by channel basis.
+
+Required properties:
+--------------------
+- compatible:		Should be
+			"ti,am654-navss-main-udmap" for am654 main NAVSS UDMAP
+			"ti,am654-navss-mcu-udmap" for am654 mcu NAVSS UDMAP
+			"ti,j721e-navss-main-udmap" for j721e main NAVSS UDMAP
+			"ti,j721e-navss-mcu-udmap" for j721e mcu NAVSS UDMAP
+- #dma-cells:		Should be set to <3>.
+			- The first parameter is a phandle to the remote PSI-L
+			  endpoint
+			- The second parameter is the thread offset within the
+			  remote thread ID range
+			- The third parameter is the channel direction.
+- reg:			Memory map of UDMAP
+- reg-names:		"gcfg", "rchanrt", "tchanrt"
+- msi-parent:		phandle for "ti,sci-inta" interrupt controller
+- ti,ringacc:		phandle for the ring accelerator node
+- ti,psil-base:		PSI-L thread ID base of the UDMAP channels
+- ti,sci:		phandle on TI-SCI compatible System controller node
+- ti,sci-dev-id:	TI-SCI device id
+- ti,sci-rm-range-tchan: UDMA tchan resource list in pairs of type and subtype
+- ti,sci-rm-range-rchan: UDMA rchan resource list in pairs of type and subtype
+- ti,sci-rm-range-rflow: UDMA rflow resource list in pairs of type and subtype
+
+For PSI-L thread management the parent NAVSS node must have:
+- ti,sci:		phandle on TI-SCI compatible System controller node
+- ti,sci-dev-id:	TI-SCI device id of the NAVSS instance
+
+Remote PSI-L endpoint
+
+Required properties:
+--------------------
+- ti,psil-base:		PSI-L thread ID base of the endpoint
+
+Within the PSI-L endpoint node thread configuration subnodes must present with:
+psil-configX naming convention, where X is the thread ID offset.
+
+Configuration node Optional properties:
+--------------------
+- pdma,statictr-type:	In case the remote endpoint (PDMAs) requires StaticTR
+			configuration:
+			- PSIL_STATIC_TR_XY (1): XY type of StaticTR
+			For endpoints without StaticTR the property is not
+			needed or to be set PSIL_STATIC_TR_NONE (0).
+- pdma,enable-acc32:	Force 32 bit access on peripheral port. Only valid for
+			XY type StaticTR, not supported on am654.
+			Must be enabled for threads servicing McASP with AFIFO
+			bypass mode.
+- pdma,enable-burst:	Enable burst access on peripheral port. Only valid for
+			XY type StaticTR, not supported on am654.
+- ti,channel-tpl:	Channel Throughput level:
+			0 / or not present - normal channel
+			1 - High Throughput channel
+			2 - Ultra High Throughput channel (j721e only)
+- ti,needs-epib:	If the endpoint require EPIB to be present in the
+			descriptor.
+- ti,psd-size:		Size of the Protocol Specific Data section of the
+			descriptor.
+
+Example:
+
+main_navss: main_navss {
+	compatible = "simple-bus";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	dma-coherent;
+	dma-ranges;
+	ranges;
+
+	ti,sci = <&dmsc>;
+	ti,sci-dev-id = <118>;
+
+	main_udmap: dma-controller@31150000 {
+		compatible = "ti,am654-navss-main-udmap";
+		reg =	<0x0 0x31150000 0x0 0x100>,
+			<0x0 0x34000000 0x0 0x100000>,
+			<0x0 0x35000000 0x0 0x100000>;
+		reg-names = "gcfg", "rchanrt", "tchanrt";
+		#dma-cells = <3>;
+
+		ti,ringacc = <&ringacc>;
+		ti,psil-base = <0x1000>;
+
+		interrupt-parent = <&main_udmass_inta>;
+
+		ti,sci = <&dmsc>;
+		ti,sci-dev-id = <188>;
+
+		ti,sci-rm-range-tchan = <0x6 0x1>, /* TX_HCHAN */
+					<0x6 0x2>; /* TX_CHAN */
+		ti,sci-rm-range-rchan = <0x6 0x4>, /* RX_HCHAN */
+					<0x6 0x5>; /* RX_CHAN */
+		ti,sci-rm-range-rflow = <0x6 0x6>; /* GP RFLOW */
+	};
+};
+
+psilss@340c000 {
+	/* PSILSS1 AASRC */
+	compatible = "ti,j721e-psilss";
+	reg = <0x0 0x0340c000 0x0 0x1000>;
+	reg-names = "config";
+
+	pdma_main_mcasp_g0: pdma_main_mcasp_g0 {
+		/* PDMA6 (PDMA_MCASP_G0) */
+		ti,psil-base = <0x4400>;
+
+		/* psil-config0 */
+		psil-config0 {
+			pdma,statictr-type = <PSIL_STATIC_TR_XY>;
+			pdma,enable-acc32;
+			pdma,enable-burst;
+		};
+	};
+};
+
+mcasp0: mcasp@02B00000 {
+...
+	/* tx: PDMA_MAIN_MCASP_G0-0, rx: PDMA_MAIN_MCASP_G0-0 */
+	dmas = <&main_udmap &pdma_main_mcasp_g0 0 UDMA_DIR_TX>,
+	       <&main_udmap &pdma_main_mcasp_g0 0 UDMA_DIR_RX>;
+	dma-names = "tx", "rx";
+...
+};
+
+crypto: crypto@4E00000 {
+	compatible = "ti,sa2ul-crypto";
+...
+
+	/* tx: crypto_pnp-1, rx: crypto_pnp-1 */
+	dmas = <&main_udmap &crypto 0 UDMA_DIR_TX>,
+	       <&main_udmap &crypto 0 UDMA_DIR_RX>,
+	       <&main_udmap &crypto 1 UDMA_DIR_RX>;
+	dma-names = "tx", "rx1", "rx2";
+...
+	psil-config0 {
+		ti,needs-epib;
+		ti,psd-size = <64>;
+	};
+
+	psil-config1 {
+		ti,needs-epib;
+		ti,psd-size = <64>;
+	};
+
+	psil-config2 {
+		ti,needs-epib;
+		ti,psd-size = <64>;
+	};
+};
diff --git a/include/dt-bindings/dma/k3-udma.h b/include/dt-bindings/dma/k3-udma.h
new file mode 100644
index 000000000000..f5c8f5d50491
--- /dev/null
+++ b/include/dt-bindings/dma/k3-udma.h
@@ -0,0 +1,10 @@
+#ifndef __DT_TI_UDMA_H
+#define __DT_TI_UDMA_H
+
+#define UDMA_DIR_TX		0
+#define UDMA_DIR_RX		1
+
+#define PSIL_STATIC_TR_NONE	0
+#define PSIL_STATIC_TR_XY	1
+
+#endif /* __DT_TI_UDMA_H */
-- 
Peter

Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki