dmaengine Archive on lore.kernel.org
 help / color / Atom feed
From: Peter Ujfalusi <peter.ujfalusi@ti.com>
To: <vkoul@kernel.org>, <robh+dt@kernel.org>, <nm@ti.com>,
	<ssantosh@kernel.org>
Cc: <dan.j.williams@intel.com>, <dmaengine@vger.kernel.org>,
	<linux-arm-kernel@lists.infradead.org>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<grygorii.strashko@ti.com>, <lokeshvutla@ti.com>,
	<t-kristo@ti.com>, <tony@atomide.com>, <j-keerthy@ti.com>
Subject: Re: [PATCH v2 02/14] soc: ti: k3: add navss ringacc driver
Date: Fri, 30 Aug 2019 15:57:16 +0300
Message-ID: <4da72d53-60cf-06ed-63c0-6cf8b4aeb690@ti.com> (raw)
In-Reply-To: <20190730093450.12664-3-peter.ujfalusi@ti.com>

Hi,

On 30/07/2019 12.34, Peter Ujfalusi wrote:
> From: Grygorii Strashko <grygorii.strashko@ti.com>
> 
> The Ring Accelerator (RINGACC or RA) provides hardware acceleration to
> enable straightforward passing of work between a producer and a consumer.
> There is one RINGACC module per NAVSS on TI AM65x SoCs.
> 
> The RINGACC converts constant-address read and write accesses to equivalent
> read or write accesses to a circular data structure in memory. The RINGACC
> eliminates the need for each DMA controller which needs to access ring
> elements from having to know the current state of the ring (base address,
> current offset). The DMA controller performs a read or write access to a
> specific address range (which maps to the source interface on the RINGACC)
> and the RINGACC replaces the address for the transaction with a new address
> which corresponds to the head or tail element of the ring (head for reads,
> tail for writes). Since the RINGACC maintains the state, multiple DMA
> controllers or channels are allowed to coherently share the same rings as
> applicable. The RINGACC is able to place data which is destined towards
> software into cached memory directly.
> 
> Supported ring modes:
> - Ring Mode
> - Messaging Mode
> - Credentials Mode
> - Queue Manager Mode
> 
> TI-SCI integration:
> 
> Texas Instrument's System Control Interface (TI-SCI) Message Protocol now
> has control over Ringacc module resources management (RM) and Rings
> configuration.
> 
> The corresponding support of TI-SCI Ringacc module RM protocol
> introduced as option through DT parameters:
> - ti,sci: phandle on TI-SCI firmware controller DT node
> - ti,sci-dev-id: TI-SCI device identifier as per TI-SCI firmware spec
> 
> if both parameters present - Ringacc driver will configure/free/reset Rings
> using TI-SCI Message Ringacc RM Protocol.
> 
> The Ringacc driver manages Rings allocation by itself now and requests
> TI-SCI firmware to allocate and configure specific Rings only. It's done
> this way because, Linux driver implements two stage Rings allocation and
> configuration (allocate ring and configure ring) while I-SCI Message
> Protocol supports only one combined operation (allocate+configure).
> 
> Grygorii Strashko <grygorii.strashko@ti.com>
> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
> ---
>  drivers/soc/ti/Kconfig            |   17 +
>  drivers/soc/ti/Makefile           |    1 +
>  drivers/soc/ti/k3-ringacc.c       | 1191 +++++++++++++++++++++++++++++
>  include/linux/soc/ti/k3-ringacc.h |  262 +++++++
>  4 files changed, 1471 insertions(+)
>  create mode 100644 drivers/soc/ti/k3-ringacc.c
>  create mode 100644 include/linux/soc/ti/k3-ringacc.h
> 
> diff --git a/drivers/soc/ti/Kconfig b/drivers/soc/ti/Kconfig
> index cf545f428d03..10c76faa503e 100644
> --- a/drivers/soc/ti/Kconfig
> +++ b/drivers/soc/ti/Kconfig
> @@ -80,6 +80,23 @@ config TI_SCI_PM_DOMAINS
>  	  called ti_sci_pm_domains. Note this is needed early in boot before
>  	  rootfs may be available.
>  
> +config TI_K3_RINGACC
> +	tristate "K3 Ring accelerator Sub System"
> +	depends on ARCH_K3 || COMPILE_TEST
> +	depends on TI_SCI_INTA_IRQCHIP
> +	default y
> +	help
> +	  Say y here to support the K3 Ring accelerator module.
> +	  The Ring Accelerator (RINGACC or RA)  provides hardware acceleration
> +	  to enable straightforward passing of work between a producer
> +	  and a consumer. There is one RINGACC module per NAVSS on TI AM65x SoCs
> +	  If unsure, say N.
> +
> +config TI_K3_RINGACC_DEBUG
> +	tristate "K3 Ring accelerator Sub System tests and debug"
> +	depends on TI_K3_RINGACC
> +	default n
> +
>  endif # SOC_TI
>  
>  config TI_SCI_INTA_MSI_DOMAIN
> diff --git a/drivers/soc/ti/Makefile b/drivers/soc/ti/Makefile
> index b3868d392d4f..cc4bc8b08bf5 100644
> --- a/drivers/soc/ti/Makefile
> +++ b/drivers/soc/ti/Makefile
> @@ -9,3 +9,4 @@ obj-$(CONFIG_AMX3_PM)			+= pm33xx.o
>  obj-$(CONFIG_WKUP_M3_IPC)		+= wkup_m3_ipc.o
>  obj-$(CONFIG_TI_SCI_PM_DOMAINS)		+= ti_sci_pm_domains.o
>  obj-$(CONFIG_TI_SCI_INTA_MSI_DOMAIN)	+= ti_sci_inta_msi.o
> +obj-$(CONFIG_TI_K3_RINGACC)		+= k3-ringacc.o
> diff --git a/drivers/soc/ti/k3-ringacc.c b/drivers/soc/ti/k3-ringacc.c
> new file mode 100644
> index 000000000000..401dfc963319
> --- /dev/null
> +++ b/drivers/soc/ti/k3-ringacc.c
> @@ -0,0 +1,1191 @@

...

> +void k3_ringacc_ring_reset_dma(struct k3_ring *ring, u32 occ)
> +{
> +	if (!ring || !(ring->flags & K3_RING_FLAG_BUSY))
> +		return;
> +
> +	if (!ring->parent->dma_ring_reset_quirk)

k3_ringacc_ring_reset(ring); is missing from here.

> +		return;
> +
> +	if (!occ)
> +		occ = dbg_readl(&ring->rt->occ);
> +
> +	if (occ) {
> +		u32 db_ring_cnt, db_ring_cnt_cur;
> +
> +		k3_nav_dbg(ring->parent->dev, "%s %u occ: %u\n", __func__,
> +			   ring->ring_id, occ);
> +		/* 2. Reset the ring */
> +		k3_ringacc_ring_reset_sci(ring);
> +
> +		/*
> +		 * 3. Setup the ring in ring/doorbell mode
> +		 * (if not already in this mode)
> +		 */
> +		if (ring->mode != K3_RINGACC_RING_MODE_RING)
> +			k3_ringacc_ring_reconfig_qmode_sci(
> +					ring, K3_RINGACC_RING_MODE_RING);
> +		/*
> +		 * 4. Ring the doorbell 2**22 – ringOcc times.
> +		 * This will wrap the internal UDMAP ring state occupancy
> +		 * counter (which is 21-bits wide) to 0.
> +		 */
> +		db_ring_cnt = (1U << 22) - occ;
> +
> +		while (db_ring_cnt != 0) {
> +			/*
> +			 * Ring the doorbell with the maximum count each
> +			 * iteration if possible to minimize the total
> +			 * of writes
> +			 */
> +			if (db_ring_cnt > K3_RINGACC_MAX_DB_RING_CNT)
> +				db_ring_cnt_cur = K3_RINGACC_MAX_DB_RING_CNT;
> +			else
> +				db_ring_cnt_cur = db_ring_cnt;
> +
> +			writel(db_ring_cnt_cur, &ring->rt->db);
> +			db_ring_cnt -= db_ring_cnt_cur;
> +		}
> +
> +		/* 5. Restore the original ring mode (if not ring mode) */
> +		if (ring->mode != K3_RINGACC_RING_MODE_RING)
> +			k3_ringacc_ring_reconfig_qmode_sci(ring, ring->mode);
> +	}
> +
> +	/* 2. Reset the ring */
> +	k3_ringacc_ring_reset(ring);
> +}
> +EXPORT_SYMBOL_GPL(k3_ringacc_ring_reset_dma);

- Péter

Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

  reply index

Thread overview: 33+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-07-30  9:34 [PATCH v2 00/14] dmaengine/soc: Add Texas Instruments UDMA support Peter Ujfalusi
2019-07-30  9:34 ` [PATCH v2 01/14] bindings: soc: ti: add documentation for k3 ringacc Peter Ujfalusi
2019-07-30  9:34 ` [PATCH v2 02/14] soc: ti: k3: add navss ringacc driver Peter Ujfalusi
2019-08-30 12:57   ` Peter Ujfalusi [this message]
2019-09-09  6:09   ` Tero Kristo
2019-09-09  7:25     ` Vignesh Raghavendra
2019-09-09 13:00     ` Peter Ujfalusi
2019-09-09 16:58       ` Grygorii Strashko
2019-07-30  9:34 ` [PATCH v2 03/14] dmaengine: doc: Add sections for per descriptor metadata support Peter Ujfalusi
2019-07-30  9:34 ` [PATCH v2 04/14] dmaengine: Add metadata_ops for dma_async_tx_descriptor Peter Ujfalusi
2019-09-08 14:12   ` Vinod Koul
2019-09-09  6:52     ` Peter Ujfalusi
2019-07-30  9:34 ` [PATCH v2 05/14] dmaengine: Add support for reporting DMA cached data amount Peter Ujfalusi
2019-07-30  9:34 ` [PATCH v2 06/14] dmaengine: ti: Add cppi5 header for UDMA Peter Ujfalusi
2019-09-08 14:25   ` Vinod Koul
2019-09-09 10:59     ` Peter Ujfalusi
2019-09-10  7:06       ` Grygorii Strashko
2019-07-30  9:34 ` [PATCH v2 07/14] dt-bindings: dma: ti: Add document for K3 UDMA Peter Ujfalusi
2019-08-21 17:59   ` Rob Herring
2019-08-22 11:18     ` Peter Ujfalusi
2019-07-30  9:34 ` [PATCH v2 08/14] dmaengine: ti: New driver for K3 UDMA - split#1: defines, structs, io func Peter Ujfalusi
2019-09-10  7:27   ` Grygorii Strashko
2019-07-30  9:34 ` [PATCH v2 09/14] dmaengine: ti: New driver for K3 UDMA - split#2: probe/remove, xlate and filter_fn Peter Ujfalusi
2019-07-30  9:34 ` [PATCH v2 10/14] dmaengine: ti: New driver for K3 UDMA - split#3: alloc/free chan_resources Peter Ujfalusi
2019-09-10  7:25   ` Grygorii Strashko
2019-09-10  7:53     ` Peter Ujfalusi
2019-07-30  9:34 ` [PATCH v2 11/14] dmaengine: ti: New driver for K3 UDMA - split#4: dma_device callbacks 1 Peter Ujfalusi
2019-07-30  9:34 ` [PATCH v2 12/14] dmaengine: ti: New driver for K3 UDMA - split#5: dma_device callbacks 2 Peter Ujfalusi
2019-07-30  9:34 ` [PATCH v2 13/14] dmaengine: ti: New driver for K3 UDMA - split#6: Kconfig and Makefile Peter Ujfalusi
2019-07-30  9:34 ` [PATCH v2 14/14] dmaengine: ti: k3-udma: Add glue layer for non DMAengine users Peter Ujfalusi
2019-07-31  7:08 ` [PATCH v2 00/14] dmaengine/soc: Add Texas Instruments UDMA support Peter Ujfalusi
2019-08-30 12:12 ` Peter Ujfalusi
2019-09-24 13:54 ` Peter Ujfalusi

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=4da72d53-60cf-06ed-63c0-6cf8b4aeb690@ti.com \
    --to=peter.ujfalusi@ti.com \
    --cc=dan.j.williams@intel.com \
    --cc=devicetree@vger.kernel.org \
    --cc=dmaengine@vger.kernel.org \
    --cc=grygorii.strashko@ti.com \
    --cc=j-keerthy@ti.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=lokeshvutla@ti.com \
    --cc=nm@ti.com \
    --cc=robh+dt@kernel.org \
    --cc=ssantosh@kernel.org \
    --cc=t-kristo@ti.com \
    --cc=tony@atomide.com \
    --cc=vkoul@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

dmaengine Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/dmaengine/0 dmaengine/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 dmaengine dmaengine/ https://lore.kernel.org/dmaengine \
		dmaengine@vger.kernel.org
	public-inbox-index dmaengine

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.dmaengine


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git