From: Vinod Koul <vkoul@kernel.org>
To: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: nm@ti.com, ssantosh@kernel.org, robh+dt@kernel.org,
vigneshr@ti.com, dan.j.williams@intel.com, t-kristo@ti.com,
lokeshvutla@ti.com, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
dmaengine@vger.kernel.org
Subject: Re: [PATCH 01/18] dmaengine: of-dma: Add support for optional router configuration callback
Date: Mon, 9 Nov 2020 17:53:06 +0530 [thread overview]
Message-ID: <20201109122306.GO3171@vkoul-mobl> (raw)
In-Reply-To: <7a7cb455-dd09-b71f-6ecc-fd6108d37051@ti.com>
HI Peter,
On 09-11-20, 14:09, Peter Ujfalusi wrote:
> Hi Vinod,
>
> On 09/11/2020 13.45, Vinod Koul wrote:
> >> Without a channel number I can not do anything.
> >> It is close to a chicken and egg problem.
> >
> > We get 'channel' in xlate, so wont that help? I think I am still missing
> > something here :(
>
> Yes, we get channel in xlate, but we get the channel after
> ofdma->of_dma_route_allocate()
That is correct, so you need this info in allocate somehow..
> of_dma_route_allocate() si the place where DMA routers create the
> dmaspec for the DMA controller to get a channel and they up until BCDMA
> did also the HW configuration to get the event routed.
>
> For a BCDMA channel we can have three triggers:
> Global trigger 0 for the channel
> Global trigger 1 for the channel
> Local trigger for the channel
>
> Every BCDMA channel have these triggers and for all of them they are the
> same (from the channel's pow).
> bchan0 can be triggered by global trigger 0
> bchan1 can be triggered by global trigger 0
>
> But these triggers are not the same ones, the real trigger depends on
> the router, which of it's input is converted to send out an event to
> trigger bchan0_trigger0 or to trigger bchan1_trigger0.
>
> When we got the channel with the dmaspec from the router driver then we
> need to tell the router driver that it needs to send a given event in
> order to trigger the channel that we got.
>
> We can not have traditional binding for BCDMA either where we would tell
> the bchan index to be used because depending on the resource allocation
> done within sysfw that exact channel might not be even available for us.
>
> - Péter
>
> Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
> Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
--
~Vinod
next prev parent reply other threads:[~2020-11-09 12:23 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-09-30 9:13 [PATCH 00/18] dmaengine/soc: k3-udma: Add support for BCDMA and PKTDMA Peter Ujfalusi
2020-09-30 9:13 ` [PATCH 01/18] dmaengine: of-dma: Add support for optional router configuration callback Peter Ujfalusi
2020-10-07 5:44 ` Vinod Koul
2020-10-07 8:08 ` Peter Ujfalusi
2020-10-07 15:55 ` Vinod Koul
2020-10-08 6:41 ` Peter Ujfalusi
2020-10-28 5:55 ` Vinod Koul
2020-10-28 9:56 ` Peter Ujfalusi
2020-11-09 11:45 ` Vinod Koul
2020-11-09 12:09 ` Peter Ujfalusi
2020-11-09 12:23 ` Vinod Koul [this message]
2020-11-09 12:36 ` Peter Ujfalusi
2020-09-30 9:13 ` [PATCH 02/18] dmaengine: Add support for per channel coherency handling Peter Ujfalusi
2020-09-30 9:13 ` [PATCH 03/18] dmaengine: doc: client: Update for dmaengine_get_dma_device() usage Peter Ujfalusi
2020-09-30 9:13 ` [PATCH 04/18] dmaengine: dmatest: Use dmaengine_get_dma_device Peter Ujfalusi
2020-09-30 9:13 ` [PATCH 05/18] dmaengine: ti: k3-udma: Wait for peer teardown completion if supported Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 06/18] dmaengine: ti: k3-udma: Add support for second resource range from sysfw Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 07/18] dmaengine: ti: k3-udma-glue: Add function to get device pointer for DMA API Peter Ujfalusi
2020-10-07 6:53 ` Vinod Koul
2020-10-07 8:22 ` Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 08/18] dmaengine: ti: k3-udma-glue: Configure the dma_dev for rings Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 09/18] dt-bindings: dma: ti: Add document for K3 BCDMA Peter Ujfalusi
2020-10-01 6:49 ` Peter Ujfalusi
2020-10-06 19:23 ` Rob Herring
2020-10-06 19:29 ` Rob Herring
2020-10-07 9:09 ` Peter Ujfalusi
2020-10-07 15:46 ` Rob Herring
2020-10-08 8:40 ` Peter Ujfalusi
2020-10-08 19:15 ` Rob Herring
2020-10-09 8:06 ` Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 10/18] dt-bindings: dma: ti: Add document for K3 PKTDMA Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 11/18] dmaengine: ti: k3-psil: Extend psil_endpoint_config " Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 12/18] dmaengine: ti: k3-psil: Add initial map for AM64 Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 13/18] dmaengine: ti: Add support for k3 event routers Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 14/18] soc: ti: k3-ringacc: add AM64 DMA rings support Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 15/18] dmaengine: ti: k3-udma: Initial support for K3 BCDMA Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 16/18] dmaengine: ti: k3-udma: Add support for BCDMA channel TPL handling Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 17/18] dmaengine: ti: k3-udma: Initial support for K3 PKTDMA Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 18/18] dmaengine: ti: k3-udma-glue: Add " Peter Ujfalusi
2020-09-30 10:17 ` [PATCH 00/18] dmaengine/soc: k3-udma: Add support for BCDMA and PKTDMA Peter Ujfalusi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201109122306.GO3171@vkoul-mobl \
--to=vkoul@kernel.org \
--cc=dan.j.williams@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=dmaengine@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=lokeshvutla@ti.com \
--cc=nm@ti.com \
--cc=peter.ujfalusi@ti.com \
--cc=robh+dt@kernel.org \
--cc=ssantosh@kernel.org \
--cc=t-kristo@ti.com \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).