[PATCH v4 0/3] DRM driver for Sitronix ST7735R display panels

[PATCH v4 0/3] DRM driver for Sitronix ST7735R display panels

[David Lechner]

This series adds a new DRM/TinyDRM driver for Sitronix ST7735R, specifically
the Adafruit 1.8" TFT.

Nothing fancy here. Just mostly TinyDRM boilerplate with the init sequence
from the fbtft driver for the same panel.

v4 changes:
* Fix alphabetical order of device tree vendor
* change prefix on panel-specific functions/structs to panel prefix instead
  of controller
* Use gamma curve from Adafruit's Arduino library.

v3 changes:
* New patch for jianda vendor prefix
* Change compatible string in DT bindings (dropped ACK because of this)
* Use SPDX license ID

David Lechner (3):
  dt-bindings: add jianda vendor prefix
  dt-bindings: Add binding for Sitronix ST7735R display panels
  drm/tinydrm: add driver for ST7735R panels

 .../bindings/display/sitronix,st7735r.txt          |  35 ++++
 .../devicetree/bindings/vendor-prefixes.txt        |   1 +
 MAINTAINERS                                        |   6 +
 drivers/gpu/drm/tinydrm/Kconfig                    |  10 +
 drivers/gpu/drm/tinydrm/Makefile                   |   1 +
 drivers/gpu/drm/tinydrm/st7735r.c                  | 215 +++++++++++++++++++++
 6 files changed, 268 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/sitronix,st7735r.txt
 create mode 100644 drivers/gpu/drm/tinydrm/st7735r.c

-- 
2.7.4

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 1/3] dt-bindings: add jianda vendor prefix

[David Lechner]

This adds a vendor prefix "jianda" for Jiandangjing Technology Co., Ltd.

Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---

v4 changes:
* Fixed alphabetical order

v3 changes:
* new patch in v3

 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 41cb1ff0..2954ca0 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -173,6 +173,7 @@ itead	ITEAD Intelligent Systems Co.Ltd
 iwave  iWave Systems Technologies Pvt. Ltd.
 jdi	Japan Display Inc.
 jedec	JEDEC Solid State Technology Association
+jianda	Jiandangjing Technology Co., Ltd.
 karo	Ka-Ro electronics GmbH
 keithkoep	Keith & Koep GmbH
 keymile	Keymile GmbH
-- 
2.7.4

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 2/3] dt-bindings: Add binding for Sitronix ST7735R display panels

[David Lechner]

This adds a new device tree binding for Sitronix ST7735R display panels,
such as the Adafruit 1.8" TFT.

Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---

v4 changes:
* none

v3 changes:
* compatible string is changed from "sitronix,st7735r-jd-t18003-t01" to
"jianda,jd-t18003-t01", "sitronix,st7735r"

v2 changes:
* none

 .../bindings/display/sitronix,st7735r.txt          | 35 ++++++++++++++++++++++
 1 file changed, 35 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/sitronix,st7735r.txt

diff --git a/Documentation/devicetree/bindings/display/sitronix,st7735r.txt b/Documentation/devicetree/bindings/display/sitronix,st7735r.txt
new file mode 100644
index 0000000..f0a5090
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/sitronix,st7735r.txt
@@ -0,0 +1,35 @@
+Sitronix ST7735R display panels
+
+This binding is for display panels using a Sitronix ST7735R controller in SPI
+mode.
+
+Required properties:
+- compatible:	"jianda,jd-t18003-t01", "sitronix,st7735r"
+- dc-gpios:	Display data/command selection (D/CX)
+- reset-gpios:	Reset signal (RSTX)
+
+The node for this driver must be a child node of a SPI controller, hence
+all mandatory properties described in ../spi/spi-bus.txt must be specified.
+
+Optional properties:
+- rotation:	panel rotation in degrees counter clockwise (0,90,180,270)
+- backlight:	phandle of the backlight device attached to the panel
+
+Example:
+
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpio 44 GPIO_ACTIVE_HIGH>;
+	}
+
+	...
+
+	display@0{
+		compatible = "jianda,jd-t18003-t01", "sitronix,st7735r";
+		reg = <0>;
+		spi-max-frequency = <32000000>;
+		dc-gpios = <&gpio 43 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio 80 GPIO_ACTIVE_HIGH>;
+		rotation = <270>;
+		backlight = &backlight;
+	};
-- 
2.7.4

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v4 3/3] drm/tinydrm: add driver for ST7735R panels

[David Lechner]

This adds a new driver for Sitronix ST7735R display panels.

This has been tested using an Adafruit 1.8" TFT.

Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
---

v4 changes:
* renamed st7735r_pipe_enable to jd_t18003_t01_pipe_enable
* renamed st7735r_pipe_funcs to jd_t18003_t01_pipe_funcs
* changed gamma curve to one from Adafruit's Arduino library

v3 changes:
* Changed compatible string
* use SPDX license header
* Renamed mode struct to use panel name instead of controller name

v2 changes:
* Change delay from 10ms to 20ms to avoid checkpatch warning
* Use mipi_dbi_pipe_enable()/mipi_dbi_pipe_disable() to reduce duplicated code
* Rebase on drm-misc-next (tinydrm_lastclose => drm_fb_helper_lastclose)
* Use mipi_dbi_debugfs_init
* Add mipi->read_commands = NULL; since this display is write-only


 MAINTAINERS                       |   6 ++
 drivers/gpu/drm/tinydrm/Kconfig   |  10 ++
 drivers/gpu/drm/tinydrm/Makefile  |   1 +
 drivers/gpu/drm/tinydrm/st7735r.c | 215 ++++++++++++++++++++++++++++++++++++++
 4 files changed, 232 insertions(+)
 create mode 100644 drivers/gpu/drm/tinydrm/st7735r.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 528e223..b4ffbc2 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4556,6 +4556,12 @@ S:	Maintained
 F:	drivers/gpu/drm/tinydrm/st7586.c
 F:	Documentation/devicetree/bindings/display/st7586.txt
 
+DRM DRIVER FOR SITRONIX ST7735R PANELS
+M:	David Lechner <david@lechnology.com>
+S:	Maintained
+F:	drivers/gpu/drm/tinydrm/st7735r.c
+F:	Documentation/devicetree/bindings/display/st7735r.txt
+
 DRM DRIVER FOR TDFX VIDEO CARDS
 S:	Orphan / Obsolete
 F:	drivers/gpu/drm/tdfx/
diff --git a/drivers/gpu/drm/tinydrm/Kconfig b/drivers/gpu/drm/tinydrm/Kconfig
index 90c5bd5..b0e567d 100644
--- a/drivers/gpu/drm/tinydrm/Kconfig
+++ b/drivers/gpu/drm/tinydrm/Kconfig
@@ -52,3 +52,13 @@ config TINYDRM_ST7586
 	  * LEGO MINDSTORMS EV3
 
 	  If M is selected the module will be called st7586.
+
+config TINYDRM_ST7735R
+	tristate "DRM support for Sitronix ST7735R display panels"
+	depends on DRM_TINYDRM && SPI
+	select TINYDRM_MIPI_DBI
+	help
+	  DRM driver Sitronix ST7735R with one of the following LCDs:
+	  * JD-T18003-T01 1.8" 128x160 TFT
+
+	  If M is selected the module will be called st7735r.
diff --git a/drivers/gpu/drm/tinydrm/Makefile b/drivers/gpu/drm/tinydrm/Makefile
index 8aeee53..49a1119 100644
--- a/drivers/gpu/drm/tinydrm/Makefile
+++ b/drivers/gpu/drm/tinydrm/Makefile
@@ -8,3 +8,4 @@ obj-$(CONFIG_TINYDRM_ILI9225)		+= ili9225.o
 obj-$(CONFIG_TINYDRM_MI0283QT)		+= mi0283qt.o
 obj-$(CONFIG_TINYDRM_REPAPER)		+= repaper.o
 obj-$(CONFIG_TINYDRM_ST7586)		+= st7586.o
+obj-$(CONFIG_TINYDRM_ST7735R)		+= st7735r.o
diff --git a/drivers/gpu/drm/tinydrm/st7735r.c b/drivers/gpu/drm/tinydrm/st7735r.c
new file mode 100644
index 0000000..98ff447
--- /dev/null
+++ b/drivers/gpu/drm/tinydrm/st7735r.c
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * DRM driver for Sitronix ST7735R panels
+ *
+ * Copyright 2017 David Lechner <david@lechnology.com>
+ */
+
+#include <linux/delay.h>
+#include <linux/dma-buf.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/property.h>
+#include <linux/spi/spi.h>
+#include <video/mipi_display.h>
+
+#include <drm/drm_fb_helper.h>
+#include <drm/drm_gem_framebuffer_helper.h>
+#include <drm/tinydrm/mipi-dbi.h>
+#include <drm/tinydrm/tinydrm-helpers.h>
+
+#define ST7735R_FRMCTR1		0xb1
+#define ST7735R_FRMCTR2		0xb2
+#define ST7735R_FRMCTR3		0xb3
+#define ST7735R_INVCTR		0xb4
+#define ST7735R_PWCTR1		0xc0
+#define ST7735R_PWCTR2		0xc1
+#define ST7735R_PWCTR3		0xc2
+#define ST7735R_PWCTR4		0xc3
+#define ST7735R_PWCTR5		0xc4
+#define ST7735R_VMCTR1		0xc5
+#define ST7735R_GAMCTRP1	0xe0
+#define ST7735R_GAMCTRN1	0xe1
+
+#define ST7735R_MY	BIT(7)
+#define ST7735R_MX	BIT(6)
+#define ST7735R_MV	BIT(5)
+
+static void jd_t18003_t01_pipe_enable(struct drm_simple_display_pipe *pipe,
+				      struct drm_crtc_state *crtc_state)
+{
+	struct tinydrm_device *tdev = pipe_to_tinydrm(pipe);
+	struct mipi_dbi *mipi = mipi_dbi_from_tinydrm(tdev);
+	struct device *dev = tdev->drm->dev;
+	int ret;
+	u8 addr_mode;
+
+	DRM_DEBUG_KMS("\n");
+
+	mipi_dbi_hw_reset(mipi);
+
+	ret = mipi_dbi_command(mipi, MIPI_DCS_SOFT_RESET);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "Error sending command %d\n", ret);
+		return;
+	}
+
+	msleep(150);
+
+	mipi_dbi_command(mipi, MIPI_DCS_EXIT_SLEEP_MODE);
+	msleep(500);
+
+	mipi_dbi_command(mipi, ST7735R_FRMCTR1, 0x01, 0x2c, 0x2d);
+	mipi_dbi_command(mipi, ST7735R_FRMCTR2, 0x01, 0x2c, 0x2d);
+	mipi_dbi_command(mipi, ST7735R_FRMCTR3, 0x01, 0x2c, 0x2d, 0x01, 0x2c,
+			 0x2d);
+	mipi_dbi_command(mipi, ST7735R_INVCTR, 0x07);
+	mipi_dbi_command(mipi, ST7735R_PWCTR1, 0xa2, 0x02, 0x84);
+	mipi_dbi_command(mipi, ST7735R_PWCTR2, 0xc5);
+	mipi_dbi_command(mipi, ST7735R_PWCTR3, 0x0a, 0x00);
+	mipi_dbi_command(mipi, ST7735R_PWCTR4, 0x8a, 0x2a);
+	mipi_dbi_command(mipi, ST7735R_PWCTR5, 0x8a, 0xee);
+	mipi_dbi_command(mipi, ST7735R_VMCTR1, 0x0e);
+	mipi_dbi_command(mipi, MIPI_DCS_EXIT_INVERT_MODE);
+	switch (mipi->rotation) {
+	default:
+		addr_mode = ST7735R_MX | ST7735R_MY;
+		break;
+	case 90:
+		addr_mode = ST7735R_MX | ST7735R_MV;
+		break;
+	case 180:
+		addr_mode = 0;
+		break;
+	case 270:
+		addr_mode = ST7735R_MY | ST7735R_MV;
+		break;
+	}
+	mipi_dbi_command(mipi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode);
+	mipi_dbi_command(mipi, MIPI_DCS_SET_PIXEL_FORMAT,
+			 MIPI_DCS_PIXEL_FMT_16BIT);
+	mipi_dbi_command(mipi, ST7735R_GAMCTRP1, 0x02, 0x1c, 0x07, 0x12, 0x37,
+			 0x32, 0x29, 0x2d, 0x29, 0x25, 0x2b, 0x39, 0x00, 0x01,
+			 0x03, 0x10);
+	mipi_dbi_command(mipi, ST7735R_GAMCTRN1, 0x03, 0x1d, 0x07, 0x06, 0x2e,
+			 0x2c, 0x29, 0x2d, 0x2e, 0x2e, 0x37, 0x3f, 0x00, 0x00,
+			 0x02, 0x10);
+	mipi_dbi_command(mipi, MIPI_DCS_SET_DISPLAY_ON);
+
+	msleep(100);
+
+	mipi_dbi_command(mipi, MIPI_DCS_ENTER_NORMAL_MODE);
+
+	msleep(20);
+
+	mipi_dbi_pipe_enable(pipe, crtc_state);
+}
+
+static const struct drm_simple_display_pipe_funcs jd_t18003_t01_pipe_funcs = {
+	.enable		= jd_t18003_t01_pipe_enable,
+	.disable	= mipi_dbi_pipe_disable,
+	.update		= tinydrm_display_pipe_update,
+	.prepare_fb	= tinydrm_display_pipe_prepare_fb,
+};
+
+static const struct drm_display_mode jd_t18003_t01_mode = {
+	TINYDRM_MODE(128, 160, 28, 35),
+};
+
+DEFINE_DRM_GEM_CMA_FOPS(st7735r_fops);
+
+static struct drm_driver st7735r_driver = {
+	.driver_features	= DRIVER_GEM | DRIVER_MODESET | DRIVER_PRIME |
+				  DRIVER_ATOMIC,
+	.fops			= &st7735r_fops,
+	TINYDRM_GEM_DRIVER_OPS,
+	.lastclose		= drm_fb_helper_lastclose,
+	.debugfs_init		= mipi_dbi_debugfs_init,
+	.name			= "st7735r",
+	.desc			= "Sitronix ST7735R",
+	.date			= "20171128",
+	.major			= 1,
+	.minor			= 0,
+};
+
+static const struct of_device_id st7735r_of_match[] = {
+	{ .compatible = "jianda,jd-t18003-t01" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, st7735r_of_match);
+
+static const struct spi_device_id st7735r_id[] = {
+	{ "jd-t18003-t01", 0 },
+	{ },
+};
+MODULE_DEVICE_TABLE(spi, st7735r_id);
+
+static int st7735r_probe(struct spi_device *spi)
+{
+	struct device *dev = &spi->dev;
+	struct mipi_dbi *mipi;
+	struct gpio_desc *dc;
+	u32 rotation = 0;
+	int ret;
+
+	mipi = devm_kzalloc(dev, sizeof(*mipi), GFP_KERNEL);
+	if (!mipi)
+		return -ENOMEM;
+
+	mipi->reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(mipi->reset)) {
+		DRM_DEV_ERROR(dev, "Failed to get gpio 'reset'\n");
+		return PTR_ERR(mipi->reset);
+	}
+
+	dc = devm_gpiod_get(dev, "dc", GPIOD_OUT_LOW);
+	if (IS_ERR(dc)) {
+		DRM_DEV_ERROR(dev, "Failed to get gpio 'dc'\n");
+		return PTR_ERR(dc);
+	}
+
+	mipi->backlight = tinydrm_of_find_backlight(dev);
+	if (IS_ERR(mipi->backlight))
+		return PTR_ERR(mipi->backlight);
+
+	device_property_read_u32(dev, "rotation", &rotation);
+
+	ret = mipi_dbi_spi_init(spi, mipi, dc);
+	if (ret)
+		return ret;
+
+	/* Cannot read from Adafruit 1.8" display via SPI */
+	mipi->read_commands = NULL;
+
+	ret = mipi_dbi_init(&spi->dev, mipi, &jd_t18003_t01_pipe_funcs,
+			    &st7735r_driver, &jd_t18003_t01_mode, rotation);
+	if (ret)
+		return ret;
+
+	spi_set_drvdata(spi, mipi);
+
+	return devm_tinydrm_register(&mipi->tinydrm);
+}
+
+static void st7735r_shutdown(struct spi_device *spi)
+{
+	struct mipi_dbi *mipi = spi_get_drvdata(spi);
+
+	tinydrm_shutdown(&mipi->tinydrm);
+}
+
+static struct spi_driver st7735r_spi_driver = {
+	.driver = {
+		.name = "st7735r",
+		.owner = THIS_MODULE,
+		.of_match_table = st7735r_of_match,
+	},
+	.id_table = st7735r_id,
+	.probe = st7735r_probe,
+	.shutdown = st7735r_shutdown,
+};
+module_spi_driver(st7735r_spi_driver);
+
+MODULE_DESCRIPTION("Sitronix ST7735R DRM driver");
+MODULE_AUTHOR("David Lechner <david@lechnology.com>");
+MODULE_LICENSE("GPL");
-- 
2.7.4

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v4 2/3] dt-bindings: Add binding for Sitronix ST7735R display panels

[Linus Walleij]

On Mon, Jan 1, 2018 at 8:02 PM, David Lechner <david@lechnology.com> wrote:

> This adds a new device tree binding for Sitronix ST7735R display panels,
> such as the Adafruit 1.8" TFT.
>
> Signed-off-by: David Lechner <david@lechnology.com>
> Reviewed-by: Rob Herring <robh@kernel.org>

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v4 3/3] drm/tinydrm: add driver for ST7735R panels

[Linus Walleij]

On Mon, Jan 1, 2018 at 8:02 PM, David Lechner <david@lechnology.com> wrote:

> This adds a new driver for Sitronix ST7735R display panels.
>
> This has been tested using an Adafruit 1.8" TFT.
>
> Signed-off-by: David Lechner <david@lechnology.com>
> Reviewed-by: Noralf Trønnes <noralf@tronnes.org>

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v4 3/3] drm/tinydrm: add driver for ST7735R panels

[Noralf Trønnes]

Den 02.01.2018 10.42, skrev Linus Walleij:
> On Mon, Jan 1, 2018 at 8:02 PM, David Lechner <david-nq/r/kbU++upp/zk7JDF2g@public.gmane.org> wrote:
>
>> This adds a new driver for Sitronix ST7735R display panels.
>>
>> This has been tested using an Adafruit 1.8" TFT.
>>
>> Signed-off-by: David Lechner <david-nq/r/kbU++upp/zk7JDF2g@public.gmane.org>
>> Reviewed-by: Noralf Trønnes <noralf-L59+Z2yzLopAfugRpC6u6w@public.gmane.org>
> Reviewed-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>

Thanks, series applied to drm-misc.

Noralf.

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html