dri-devel.lists.freedesktop.org archive mirror
 help / color / mirror / Atom feed
From: Eric Anholt <eric@anholt.net>
To: dri-devel@lists.freedesktop.org,
	Archit Taneja <architt@codeaurora.org>,
	Andrzej Hajda <a.hajda@samsung.com>,
	Laurent Pinchart <Laurent.pinchart@ideasonboard.com>,
	Thierry Reding <thierry.reding@gmail.com>
Cc: linux-kernel@vger.kernel.org
Subject: [PATCH 2/8] drm/vc4: Fix misleading name of the continuous flag.
Date: Tue, 27 Jun 2017 12:58:33 -0700	[thread overview]
Message-ID: <20170627195839.3338-3-eric@anholt.net> (raw)
In-Reply-To: <20170627195839.3338-1-eric@anholt.net>

The logic was all right in the end, the name was just backwards.

Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/vc4/vc4_dsi.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/vc4/vc4_dsi.c b/drivers/gpu/drm/vc4/vc4_dsi.c
index 15f6d5005ab9..629d372633e6 100644
--- a/drivers/gpu/drm/vc4/vc4_dsi.c
+++ b/drivers/gpu/drm/vc4/vc4_dsi.c
@@ -736,18 +736,18 @@ static void vc4_dsi_latch_ulps(struct vc4_dsi *dsi, bool latch)
 /* Enters or exits Ultra Low Power State. */
 static void vc4_dsi_ulps(struct vc4_dsi *dsi, bool ulps)
 {
-	bool continuous = dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS;
-	u32 phyc_ulps = ((continuous ? DSI_PORT_BIT(PHYC_CLANE_ULPS) : 0) |
+	bool non_continuous = dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS;
+	u32 phyc_ulps = ((non_continuous ? DSI_PORT_BIT(PHYC_CLANE_ULPS) : 0) |
 			 DSI_PHYC_DLANE0_ULPS |
 			 (dsi->lanes > 1 ? DSI_PHYC_DLANE1_ULPS : 0) |
 			 (dsi->lanes > 2 ? DSI_PHYC_DLANE2_ULPS : 0) |
 			 (dsi->lanes > 3 ? DSI_PHYC_DLANE3_ULPS : 0));
-	u32 stat_ulps = ((continuous ? DSI1_STAT_PHY_CLOCK_ULPS : 0) |
+	u32 stat_ulps = ((non_continuous ? DSI1_STAT_PHY_CLOCK_ULPS : 0) |
 			 DSI1_STAT_PHY_D0_ULPS |
 			 (dsi->lanes > 1 ? DSI1_STAT_PHY_D1_ULPS : 0) |
 			 (dsi->lanes > 2 ? DSI1_STAT_PHY_D2_ULPS : 0) |
 			 (dsi->lanes > 3 ? DSI1_STAT_PHY_D3_ULPS : 0));
-	u32 stat_stop = ((continuous ? DSI1_STAT_PHY_CLOCK_STOP : 0) |
+	u32 stat_stop = ((non_continuous ? DSI1_STAT_PHY_CLOCK_STOP : 0) |
 			 DSI1_STAT_PHY_D0_STOP |
 			 (dsi->lanes > 1 ? DSI1_STAT_PHY_D1_STOP : 0) |
 			 (dsi->lanes > 2 ? DSI1_STAT_PHY_D2_STOP : 0) |
-- 
2.11.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

  parent reply	other threads:[~2017-06-27 19:58 UTC|newest]

Thread overview: 26+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-06-27 19:58 [PATCH 0/8] RPi touchscreen panel driver v4 Eric Anholt
2017-06-27 19:58 ` [PATCH 1/8] drm/vc4: Fix DSI T_INIT timing Eric Anholt
2017-06-29  9:02   ` Andrzej Hajda
2017-06-27 19:58 ` Eric Anholt [this message]
2017-06-29  9:03   ` [PATCH 2/8] drm/vc4: Fix misleading name of the continuous flag Andrzej Hajda
2017-06-27 19:58 ` [PATCH 3/8] drm/vc4: Use drm_mode_vrefresh() in DSI fixup, in case vrefresh is 0 Eric Anholt
2017-06-29  9:24   ` Andrzej Hajda
2017-06-27 19:58 ` [PATCH 4/8] drm/bridge: Add a devm_ allocator for panel bridge Eric Anholt
2017-06-29  9:30   ` Andrzej Hajda
2017-06-27 19:58 ` [PATCH 5/8] drm/vc4: Delay DSI host registration until the panel has probed Eric Anholt
2017-06-29  9:42   ` Andrzej Hajda
2017-06-27 19:58 ` [PATCH 6/8] drm: Allow DSI devices to be registered before the host registers Eric Anholt
2017-06-29  5:03   ` Archit Taneja
2017-06-29 10:39     ` Andrzej Hajda
2017-06-29 15:22       ` Eric Anholt
2017-06-30  8:48         ` Andrzej Hajda
2017-07-03 10:56       ` Archit Taneja
2017-07-14 23:01         ` Eric Anholt
2017-07-17 13:39           ` Archit Taneja
2017-07-14 22:58     ` Eric Anholt
2017-07-17  4:26       ` Archit Taneja
2017-07-18 20:13         ` Eric Anholt
2017-07-19  3:29           ` Archit Taneja
2017-08-04  9:29           ` Boris Brezillon
2017-06-27 19:58 ` [PATCH 7/8] dt-bindings: Document the Raspberry Pi Touchscreen nodes Eric Anholt
2017-06-27 19:58 ` [PATCH 8/8] drm/panel: Add support for the Raspberry Pi 7" Touchscreen Eric Anholt

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20170627195839.3338-3-eric@anholt.net \
    --to=eric@anholt.net \
    --cc=Laurent.pinchart@ideasonboard.com \
    --cc=a.hajda@samsung.com \
    --cc=architt@codeaurora.org \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=thierry.reding@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).