[PATCH 0/5] Add support for Pine64 PineTab

[PATCH 0/5] Add support for Pine64 PineTab

[Icenowy Zheng]

This patchset tries to add support for the PineTab tablet from Pine64.

As it uses a specific MIPI-DSI panel, the support of the panel should be
introduced first, with its DT binding.

Then a device tree is added. Thanks to the community's contributions
these years, we now have most of the functionalities of the tablet
available in this device tree.

Icenowy Zheng (5):
  dt-bindings: vendor-prefix: add Shenzhen Feixin Photoelectics Co., Ltd
  dt-bindings: panel: add Feixin K101 IM2BA02 MIPI-DSI panel
  drm/panel: Add Feixin K101 IM2BA02 panel
  dt-bindings: arm: sunxi: add binding for PineTab tablet
  arm64: dts: allwinner: a64: add support for PineTab

 .../devicetree/bindings/arm/sunxi.yaml        |   5 +
 .../display/panel/feixin,k101-im2ba02.yaml    |  54 ++
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 MAINTAINERS                                   |   6 +
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../boot/dts/allwinner/sun50i-a64-pinetab.dts | 461 +++++++++++++++
 drivers/gpu/drm/panel/Kconfig                 |   9 +
 drivers/gpu/drm/panel/Makefile                |   1 +
 .../gpu/drm/panel/panel-feixin-k101-im2ba02.c | 548 ++++++++++++++++++
 9 files changed, 1087 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/feixin,k101-im2ba02.yaml
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
 create mode 100644 drivers/gpu/drm/panel/panel-feixin-k101-im2ba02.c

-- 
2.23.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH 1/5] dt-bindings: vendor-prefix: add Shenzhen Feixin Photoelectics Co., Ltd

[Icenowy Zheng]

Shenzhen Feixin Photoelectics Co., Ltd is a company to provide LCD
modules.

Add its vendor prefix.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 3dab8150dae7..a6d53bbbe33d 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -335,6 +335,8 @@ patternProperties:
     description: Fastrax Oy
   "^fcs,.*":
     description: Fairchild Semiconductor
+  "^feixin,.*":
+    description: Shenzhen Feixin Photoelectic Co., Ltd
   "^feiyang,.*":
     description: Shenzhen Fly Young Technology Co.,LTD.
   "^firefly,.*":
-- 
2.23.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH 1/5] dt-bindings: vendor-prefix: add Shenzhen Feixin Photoelectics Co., Ltd

[Sam Ravnborg]

Hi Icenowy.

On Fri, Jan 10, 2020 at 11:52:21PM +0800, Icenowy Zheng wrote:
> Shenzhen Feixin Photoelectics Co., Ltd is a company to provide LCD
> modules.
> 
> Add its vendor prefix.
> 
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

Acked-by: Sam Ravnborg <sam@ravnborg.org>

> ---
>  Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
>  1 file changed, 2 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
> index 3dab8150dae7..a6d53bbbe33d 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
> @@ -335,6 +335,8 @@ patternProperties:
>      description: Fastrax Oy
>    "^fcs,.*":
>      description: Fairchild Semiconductor
> +  "^feixin,.*":
> +    description: Shenzhen Feixin Photoelectic Co., Ltd
>    "^feiyang,.*":
>      description: Shenzhen Fly Young Technology Co.,LTD.
>    "^firefly,.*":
> -- 
> 2.23.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH 1/5] dt-bindings: vendor-prefix: add Shenzhen Feixin Photoelectics Co., Ltd

[Rob Herring]

On Fri, 10 Jan 2020 23:52:21 +0800, Icenowy Zheng wrote:
> Shenzhen Feixin Photoelectics Co., Ltd is a company to provide LCD
> modules.
> 
> Add its vendor prefix.
> 
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
>  Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
>  1 file changed, 2 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH 2/5] dt-bindings: panel: add Feixin K101 IM2BA02 MIPI-DSI panel

[Icenowy Zheng]

Feixin K101 IM2BA02 is a 10.1" 800x1280 4-lane MIPI-DSI panel.

Add device tree binding for it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
 .../display/panel/feixin,k101-im2ba02.yaml    | 54 +++++++++++++++++++
 1 file changed, 54 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/feixin,k101-im2ba02.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/feixin,k101-im2ba02.yaml b/Documentation/devicetree/bindings/display/panel/feixin,k101-im2ba02.yaml
new file mode 100644
index 000000000000..7176d14893ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/feixin,k101-im2ba02.yaml
@@ -0,0 +1,54 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/feixin,k101-im2ba02.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Feixin K101 IM2BA02 10.1" MIPI-DSI LCD panel
+
+maintainers:
+  - Icenowy Zheng <icenowy@aosc.io>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: feixin,k101-im2ba02
+  reg: true
+  backlight: true
+  reset-gpios: true
+  avdd-supply:
+     description: regulator that supplies the AVDD voltage
+  dvdd-supply:
+     description: regulator that supplies the DVDD voltage
+  cvdd-supply:
+     description: regulator that supplies the CVDD voltage
+
+required:
+  - compatible
+  - reg
+  - backlight
+  - avdd-supply
+  - dvdd-supply
+  - cvdd-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    &dsi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        panel@0 {
+            compatible = "feixin,k101-im2ba02";
+            reg = <0>;
+            avdd-supply = <&reg_dc1sw>;
+            dvdd-supply = <&reg_dc1sw>;
+            cvdd-supply = <&reg_ldo_io1>;
+            reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>;
+            backlight = <&backlight>;
+        };
+    };
+
+...
-- 
2.23.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH 2/5] dt-bindings: panel: add Feixin K101 IM2BA02 MIPI-DSI panel

[Sam Ravnborg]

Hi Icenowy.

On Fri, Jan 10, 2020 at 11:52:22PM +0800, Icenowy Zheng wrote:
> Feixin K101 IM2BA02 is a 10.1" 800x1280 4-lane MIPI-DSI panel.
> 
> Add device tree binding for it.
Thanks for using the new meta-schema format and with the correct
license.


The example fails dt_binding_check - I had to do the following to make
it pass:

diff --git a/Documentation/devicetree/bindings/display/panel/feixin,k101-im2ba02.yaml b/Documentation/devicetree/bindings/display/panel/feixin,k101-im2ba02.yaml
index 7176d14893ff..c43f884de6ac 100644
--- a/Documentation/devicetree/bindings/display/panel/feixin,k101-im2ba02.yaml
+++ b/Documentation/devicetree/bindings/display/panel/feixin,k101-im2ba02.yaml
@@ -37,7 +37,9 @@ additionalProperties: false
 
 examples:
   - |
-    &dsi {
+    #include <dt-bindings/gpio/gpio.h>
+
+    dsi {
         #address-cells = <1>;
         #size-cells = <0>;
         panel@0 {

Added include to get definition of GPIO_...
And dropped the "&" as it is not OK in the example here.

And please consider if backlight really is a required property.

	Sam
> 
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
>  .../display/panel/feixin,k101-im2ba02.yaml    | 54 +++++++++++++++++++
>  1 file changed, 54 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/panel/feixin,k101-im2ba02.yaml
> 
> diff --git a/Documentation/devicetree/bindings/display/panel/feixin,k101-im2ba02.yaml b/Documentation/devicetree/bindings/display/panel/feixin,k101-im2ba02.yaml
> new file mode 100644
> index 000000000000..7176d14893ff
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/panel/feixin,k101-im2ba02.yaml
> @@ -0,0 +1,54 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/panel/feixin,k101-im2ba02.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Feixin K101 IM2BA02 10.1" MIPI-DSI LCD panel
> +
> +maintainers:
> +  - Icenowy Zheng <icenowy@aosc.io>
> +
> +allOf:
> +  - $ref: panel-common.yaml#
> +
> +properties:
> +  compatible:
> +    const: feixin,k101-im2ba02
> +  reg: true
> +  backlight: true
> +  reset-gpios: true
> +  avdd-supply:
> +     description: regulator that supplies the AVDD voltage
> +  dvdd-supply:
> +     description: regulator that supplies the DVDD voltage
> +  cvdd-supply:
> +     description: regulator that supplies the CVDD voltage
> +
> +required:
> +  - compatible
> +  - reg
> +  - backlight
> +  - avdd-supply
> +  - dvdd-supply
> +  - cvdd-supply
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    &dsi {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +        panel@0 {
> +            compatible = "feixin,k101-im2ba02";
> +            reg = <0>;
> +            avdd-supply = <&reg_dc1sw>;
> +            dvdd-supply = <&reg_dc1sw>;
> +            cvdd-supply = <&reg_ldo_io1>;
> +            reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>;
> +            backlight = <&backlight>;
> +        };
> +    };
> +
> +...
> -- 
> 2.23.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH 3/5] drm/panel: Add Feixin K101 IM2BA02 panel

[Icenowy Zheng]

Feixin K101 IM2BA02 is a 800x1280 4-lane MIPI-DSI LCD panel.

Add a panel driver for it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
 MAINTAINERS                                   |   6 +
 drivers/gpu/drm/panel/Kconfig                 |   9 +
 drivers/gpu/drm/panel/Makefile                |   1 +
 .../gpu/drm/panel/panel-feixin-k101-im2ba02.c | 548 ++++++++++++++++++
 4 files changed, 564 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-feixin-k101-im2ba02.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 908399316455..ef7d13125344 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5218,6 +5218,12 @@ T:	git git://anongit.freedesktop.org/drm/drm-misc
 S:	Maintained
 F:	drivers/gpu/drm/tve200/
 
+DRM DRIVER FOR FEIXIN K101 IM2BA02 MIPI-DSI LCD PANELS
+M:	Icenowy Zheng <icenowy@aosc.io>
+S:	Maintained
+F:	drivers/gpu/drm/panel/panel-feixin-k101-im2ba02.c
+F:	Documentation/devicetree/bindings/display/panel/feixin,k101-im2ba02.yaml
+
 DRM DRIVER FOR FEIYANG FY07024DI26A30-D MIPI-DSI LCD PANELS
 M:	Jagan Teki <jagan@amarulasolutions.com>
 S:	Maintained
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index ae44ac2ec106..4641ec804e5e 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -50,6 +50,15 @@ config DRM_PANEL_SIMPLE
 	  that it can be automatically turned off when the panel goes into a
 	  low power state.
 
+config DRM_PANEL_FEIXIN_K101_IM2BA02
+	tristate "Feixin K101 IM2BA02 panel"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	depends on BACKLIGHT_CLASS_DEVICE
+	help
+	  Say Y here if you want to enable support for the Feixin K101 IM2BA02
+	  4-lane 800x1280 MIPI DSI panel.
+
 config DRM_PANEL_FEIYANG_FY07024DI26A30D
 	tristate "Feiyang FY07024DI26A30-D MIPI-DSI LCD panel"
 	depends on OF
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index 7c4d3c581fd4..442c17ccc62e 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -3,6 +3,7 @@ obj-$(CONFIG_DRM_PANEL_ARM_VERSATILE) += panel-arm-versatile.o
 obj-$(CONFIG_DRM_PANEL_BOE_HIMAX8279D) += panel-boe-himax8279d.o
 obj-$(CONFIG_DRM_PANEL_LVDS) += panel-lvds.o
 obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o
+obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o
 obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o
 obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o
 obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o
diff --git a/drivers/gpu/drm/panel/panel-feixin-k101-im2ba02.c b/drivers/gpu/drm/panel/panel-feixin-k101-im2ba02.c
new file mode 100644
index 000000000000..45a62bdabb3f
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-feixin-k101-im2ba02.c
@@ -0,0 +1,548 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019-2020 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+#include <linux/gpio/consumer.h>
+#include <linux/delay.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regulator/consumer.h>
+
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_print.h>
+
+#define K101_IM2BA02_INIT_CMD_LEN	2
+
+struct k101_im2ba02 {
+	struct drm_panel	panel;
+	struct mipi_dsi_device	*dsi;
+
+	struct regulator	*dvdd;
+	struct regulator	*avdd;
+	struct regulator	*cvdd;
+	struct gpio_desc	*reset;
+};
+
+static inline struct k101_im2ba02 *panel_to_k101_im2ba02(struct drm_panel *panel)
+{
+	return container_of(panel, struct k101_im2ba02, panel);
+}
+
+struct k101_im2ba02_init_cmd {
+	u8 data[K101_IM2BA02_INIT_CMD_LEN];
+};
+
+static const struct k101_im2ba02_init_cmd k101_im2ba02_init_cmds[] = {
+	/* Switch to page 0 */
+	{ .data = { 0xE0, 0x00 } },
+
+	/* Seems to be some password */
+	{ .data = { 0xE1, 0x93} },
+	{ .data = { 0xE2, 0x65 } },
+	{ .data = { 0xE3, 0xF8 } },
+
+	/* Lane number, 0x02 - 3 lanes, 0x03 - 4 lanes */
+	{ .data = { 0x80, 0x03 } },
+
+	/* Sequence control */
+	{ .data = { 0x70, 0x02 } },
+	{ .data = { 0x71, 0x23 } },
+	{ .data = { 0x72, 0x06 } },
+
+	/* Switch to page 1 */
+	{ .data = { 0xE0, 0x01 } },
+
+	/* Set VCOM */
+	{ .data = { 0x00, 0x00 } },
+	{ .data = { 0x01, 0x66 } },
+	/* Set VCOM_Reverse */
+	{ .data = { 0x03, 0x00 } },
+	{ .data = { 0x04, 0x25 } },
+
+	/* Set Gamma Power, VG[MS][PN] */
+	{ .data = { 0x17, 0x00 } },
+	{ .data = { 0x18, 0x6D } },
+	{ .data = { 0x19, 0x00 } },
+	{ .data = { 0x1A, 0x00 } },
+	{ .data = { 0x1B, 0xBF } }, /* VGMN = -4.5V */
+	{ .data = { 0x1C, 0x00 } },
+
+	/* Set Gate Power */
+	{ .data = { 0x1F, 0x3E } }, /* VGH_R = 15V */
+	{ .data = { 0x20, 0x28 } }, /* VGL_R = -11V */
+	{ .data = { 0x21, 0x28 } }, /* VGL_R2 = -11V */
+	{ .data = { 0x22, 0x0E } }, /* PA[6:4] = 0, PA[0] = 0 */
+
+	/* Set Panel */
+	{ .data = { 0x37, 0x09 } }, /* SS = 1, BGR = 1 */
+
+	/* Set RGBCYC */
+	{ .data = { 0x38, 0x04 } }, /* JDT = 100 column inversion */
+	{ .data = { 0x39, 0x08 } }, /* RGB_N_EQ1 */
+	{ .data = { 0x3A, 0x12 } }, /* RGB_N_EQ2 */
+	{ .data = { 0x3C, 0x78 } }, /* set EQ3 for TE_H */
+	{ .data = { 0x3D, 0xFF } }, /* set CHGEN_ON */
+	{ .data = { 0x3E, 0xFF } }, /* set CHGEN_OFF */
+	{ .data = { 0x3F, 0x7F } }, /* set CHGEN_OFF2 */
+
+	/* Set TCON parameter */
+	{ .data = { 0x40, 0x06 } }, /* RSO = 800 points */
+	{ .data = { 0x41, 0xA0 } }, /* LN = 1280 lines */
+
+	/* Set power voltage */
+	{ .data = { 0x55, 0x0F } }, /* DCDCM */
+	{ .data = { 0x56, 0x01 } },
+	{ .data = { 0x57, 0x69 } },
+	{ .data = { 0x58, 0x0A } },
+	{ .data = { 0x59, 0x0A } },
+	{ .data = { 0x5A, 0x45 } },
+	{ .data = { 0x5B, 0x15 } },
+
+	/* Set gamma */
+	{ .data = { 0x5D, 0x7C } },
+	{ .data = { 0x5E, 0x65 } },
+	{ .data = { 0x5F, 0x55 } },
+	{ .data = { 0x60, 0x49 } },
+	{ .data = { 0x61, 0x44 } },
+	{ .data = { 0x62, 0x35 } },
+	{ .data = { 0x63, 0x3A } },
+	{ .data = { 0x64, 0x23 } },
+	{ .data = { 0x65, 0x3D } },
+	{ .data = { 0x66, 0x3C } },
+	{ .data = { 0x67, 0x3D } },
+	{ .data = { 0x68, 0x5D } },
+	{ .data = { 0x69, 0x4D } },
+	{ .data = { 0x6A, 0x56 } },
+	{ .data = { 0x6B, 0x48 } },
+	{ .data = { 0x6C, 0x45 } },
+	{ .data = { 0x6D, 0x38 } },
+	{ .data = { 0x6E, 0x25 } },
+	{ .data = { 0x6F, 0x00 } },
+	{ .data = { 0x70, 0x7C } },
+	{ .data = { 0x71, 0x65 } },
+	{ .data = { 0x72, 0x55 } },
+	{ .data = { 0x73, 0x49 } },
+	{ .data = { 0x74, 0x44 } },
+	{ .data = { 0x75, 0x35 } },
+	{ .data = { 0x76, 0x3A } },
+	{ .data = { 0x77, 0x23 } },
+	{ .data = { 0x78, 0x3D } },
+	{ .data = { 0x79, 0x3C } },
+	{ .data = { 0x7A, 0x3D } },
+	{ .data = { 0x7B, 0x5D } },
+	{ .data = { 0x7C, 0x4D } },
+	{ .data = { 0x7D, 0x56 } },
+	{ .data = { 0x7E, 0x48 } },
+	{ .data = { 0x7F, 0x45 } },
+	{ .data = { 0x80, 0x38 } },
+	{ .data = { 0x81, 0x25 } },
+	{ .data = { 0x82, 0x00 } },
+
+	/* Switch to page 2, for GIP */
+	{ .data = { 0xE0, 0x02 } },
+
+	{ .data = { 0x00, 0x1E } },
+	{ .data = { 0x01, 0x1E } },
+	{ .data = { 0x02, 0x41 } },
+	{ .data = { 0x03, 0x41 } },
+	{ .data = { 0x04, 0x43 } },
+	{ .data = { 0x05, 0x43 } },
+	{ .data = { 0x06, 0x1F } },
+	{ .data = { 0x07, 0x1F } },
+	{ .data = { 0x08, 0x1F } },
+	{ .data = { 0x09, 0x1F } },
+	{ .data = { 0x0A, 0x1E } },
+	{ .data = { 0x0B, 0x1E } },
+	{ .data = { 0x0C, 0x1F } },
+	{ .data = { 0x0D, 0x47 } },
+	{ .data = { 0x0E, 0x47 } },
+	{ .data = { 0x0F, 0x45 } },
+	{ .data = { 0x10, 0x45 } },
+	{ .data = { 0x11, 0x4B } },
+	{ .data = { 0x12, 0x4B } },
+	{ .data = { 0x13, 0x49 } },
+	{ .data = { 0x14, 0x49 } },
+	{ .data = { 0x15, 0x1F } },
+
+	{ .data = { 0x16, 0x1E } },
+	{ .data = { 0x17, 0x1E } },
+	{ .data = { 0x18, 0x40 } },
+	{ .data = { 0x19, 0x40 } },
+	{ .data = { 0x1A, 0x42 } },
+	{ .data = { 0x1B, 0x42 } },
+	{ .data = { 0x1C, 0x1F } },
+	{ .data = { 0x1D, 0x1F } },
+	{ .data = { 0x1E, 0x1F } },
+	{ .data = { 0x1F, 0x1f } },
+	{ .data = { 0x20, 0x1E } },
+	{ .data = { 0x21, 0x1E } },
+	{ .data = { 0x22, 0x1f } },
+	{ .data = { 0x23, 0x46 } },
+	{ .data = { 0x24, 0x46 } },
+	{ .data = { 0x25, 0x44 } },
+	{ .data = { 0x26, 0x44 } },
+	{ .data = { 0x27, 0x4A } },
+	{ .data = { 0x28, 0x4A } },
+	{ .data = { 0x29, 0x48 } },
+	{ .data = { 0x2A, 0x48 } },
+	{ .data = { 0x2B, 0x1f } },
+
+	{ .data = { 0x2C, 0x1F } },
+	{ .data = { 0x2D, 0x1F } },
+	{ .data = { 0x2E, 0x42 } },
+	{ .data = { 0x2F, 0x42 } },
+	{ .data = { 0x30, 0x40 } },
+	{ .data = { 0x31, 0x40 } },
+	{ .data = { 0x32, 0x1E } },
+	{ .data = { 0x33, 0x1E } },
+	{ .data = { 0x34, 0x1F } },
+	{ .data = { 0x35, 0x1F } },
+	{ .data = { 0x36, 0x1E } },
+	{ .data = { 0x37, 0x1E } },
+	{ .data = { 0x38, 0x1F } },
+	{ .data = { 0x39, 0x48 } },
+	{ .data = { 0x3A, 0x48 } },
+	{ .data = { 0x3B, 0x4A } },
+	{ .data = { 0x3C, 0x4A } },
+	{ .data = { 0x3D, 0x44 } },
+	{ .data = { 0x3E, 0x44 } },
+	{ .data = { 0x3F, 0x46 } },
+	{ .data = { 0x40, 0x46 } },
+	{ .data = { 0x41, 0x1F } },
+
+	{ .data = { 0x42, 0x1F } },
+	{ .data = { 0x43, 0x1F } },
+	{ .data = { 0x44, 0x43 } },
+	{ .data = { 0x45, 0x43 } },
+	{ .data = { 0x46, 0x41 } },
+	{ .data = { 0x47, 0x41 } },
+	{ .data = { 0x48, 0x1E } },
+	{ .data = { 0x49, 0x1E } },
+	{ .data = { 0x4A, 0x1E } },
+	{ .data = { 0x4B, 0x1F } },
+	{ .data = { 0x4C, 0x1E } },
+	{ .data = { 0x4D, 0x1E } },
+	{ .data = { 0x4E, 0x1F } },
+	{ .data = { 0x4F, 0x49 } },
+	{ .data = { 0x50, 0x49 } },
+	{ .data = { 0x51, 0x4B } },
+	{ .data = { 0x52, 0x4B } },
+	{ .data = { 0x53, 0x45 } },
+	{ .data = { 0x54, 0x45 } },
+	{ .data = { 0x55, 0x47 } },
+	{ .data = { 0x56, 0x47 } },
+	{ .data = { 0x57, 0x1F } },
+
+	{ .data = { 0x58, 0x10 } },
+	{ .data = { 0x59, 0x00 } },
+	{ .data = { 0x5A, 0x00 } },
+	{ .data = { 0x5B, 0x30 } },
+	{ .data = { 0x5C, 0x02 } },
+	{ .data = { 0x5D, 0x40 } },
+	{ .data = { 0x5E, 0x01 } },
+	{ .data = { 0x5F, 0x02 } },
+	{ .data = { 0x60, 0x30 } },
+	{ .data = { 0x61, 0x01 } },
+	{ .data = { 0x62, 0x02 } },
+	{ .data = { 0x63, 0x6A } },
+	{ .data = { 0x64, 0x6A } },
+	{ .data = { 0x65, 0x05 } },
+	{ .data = { 0x66, 0x12 } },
+	{ .data = { 0x67, 0x74 } },
+	{ .data = { 0x68, 0x04 } },
+	{ .data = { 0x69, 0x6A } },
+	{ .data = { 0x6A, 0x6A } },
+	{ .data = { 0x6B, 0x08 } },
+
+	{ .data = { 0x6C, 0x00 } },
+	{ .data = { 0x6D, 0x04 } },
+	{ .data = { 0x6E, 0x04 } },
+	{ .data = { 0x6F, 0x88 } },
+	{ .data = { 0x70, 0x00 } },
+	{ .data = { 0x71, 0x00 } },
+	{ .data = { 0x72, 0x06 } },
+	{ .data = { 0x73, 0x7B } },
+	{ .data = { 0x74, 0x00 } },
+	{ .data = { 0x75, 0x07 } },
+	{ .data = { 0x76, 0x00 } },
+	{ .data = { 0x77, 0x5D } },
+	{ .data = { 0x78, 0x17 } },
+	{ .data = { 0x79, 0x1F } },
+	{ .data = { 0x7A, 0x00 } },
+	{ .data = { 0x7B, 0x00 } },
+	{ .data = { 0x7C, 0x00 } },
+	{ .data = { 0x7D, 0x03 } },
+	{ .data = { 0x7E, 0x7B } },
+
+	{ .data = { 0xE0, 0x04 } },
+	{ .data = { 0x2B, 0x2B } },
+	{ .data = { 0x2E, 0x44 } },
+
+	{ .data = { 0xE0, 0x01 } },
+	{ .data = { 0x0E, 0x01 } },
+
+	{ .data = { 0xE0, 0x03 } },
+	{ .data = { 0x98, 0x2F } },
+
+	{ .data = { 0xE0, 0x00 } },
+	{ .data = { 0xE6, 0x02 } },
+	{ .data = { 0xE7, 0x02 } },
+
+	{ .data = { 0x11, 0x00 } },
+};
+
+static const struct k101_im2ba02_init_cmd timed_cmds[] = {
+	{ .data = { 0x29, 0x00 } },
+	{ .data = { 0x35, 0x00 } },
+};
+
+static int k101_im2ba02_prepare(struct drm_panel *panel)
+{
+	struct k101_im2ba02 *ctx = panel_to_k101_im2ba02(panel);
+	struct mipi_dsi_device *dsi = ctx->dsi;
+	unsigned int i;
+	int ret;
+
+	ret = regulator_enable(ctx->avdd);
+	if (ret)
+		return ret;
+
+	msleep(20);
+
+	ret = regulator_enable(ctx->dvdd);
+	if (ret)
+		return ret;
+
+	msleep(20);
+
+	ret = regulator_enable(ctx->cvdd);
+	if (ret)
+		return ret;
+
+	msleep(30);
+
+	gpiod_set_value(ctx->reset, 1);
+	msleep(50);
+
+	gpiod_set_value(ctx->reset, 0);
+	msleep(50);
+
+	gpiod_set_value(ctx->reset, 1);
+	msleep(200);
+
+	for (i = 0; i < ARRAY_SIZE(k101_im2ba02_init_cmds); i++) {
+		const struct k101_im2ba02_init_cmd *cmd = &k101_im2ba02_init_cmds[i];
+
+		ret = mipi_dsi_dcs_write_buffer(dsi, cmd->data, K101_IM2BA02_INIT_CMD_LEN);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int k101_im2ba02_enable(struct drm_panel *panel)
+{
+	struct k101_im2ba02 *ctx = panel_to_k101_im2ba02(panel);
+	const struct k101_im2ba02_init_cmd *cmd = &timed_cmds[1];
+	int ret;
+
+	msleep(150);
+
+	ret = mipi_dsi_dcs_set_display_on(ctx->dsi);
+	if (ret < 0)
+		return ret;
+
+	msleep(50);
+
+	return mipi_dsi_dcs_write_buffer(ctx->dsi, cmd->data, K101_IM2BA02_INIT_CMD_LEN);
+	if (ret < 0)
+		return ret;
+}
+
+static int k101_im2ba02_disable(struct drm_panel *panel)
+{
+	struct k101_im2ba02 *ctx = panel_to_k101_im2ba02(panel);
+
+	return mipi_dsi_dcs_set_display_off(ctx->dsi);
+}
+
+static int k101_im2ba02_unprepare(struct drm_panel *panel)
+{
+	struct k101_im2ba02 *ctx = panel_to_k101_im2ba02(panel);
+	int ret;
+
+	ret = mipi_dsi_dcs_set_display_off(ctx->dsi);
+	if (ret < 0)
+		DRM_DEV_ERROR(panel->dev, "failed to set display off: %d\n",
+			      ret);
+
+	ret = mipi_dsi_dcs_enter_sleep_mode(ctx->dsi);
+	if (ret < 0)
+		DRM_DEV_ERROR(panel->dev, "failed to enter sleep mode: %d\n",
+			      ret);
+
+	msleep(200);
+
+	gpiod_set_value(ctx->reset, 0);
+
+	msleep(20);
+
+	regulator_disable(ctx->cvdd);
+
+	msleep(20);
+
+	regulator_disable(ctx->dvdd);
+
+	msleep(20);
+
+	regulator_disable(ctx->avdd);
+
+	return 0;
+}
+
+static const struct drm_display_mode k101_im2ba02_default_mode = {
+	.clock = 70000,
+	.vrefresh = 60,
+
+	.hdisplay = 800,
+	.hsync_start = 800 + 20,
+	.hsync_end = 800 + 20 + 20,
+	.htotal = 800 + 20 + 20 + 20,
+
+	.vdisplay = 1280,
+	.vsync_start = 1280 + 16,
+	.vsync_end = 1280 + 16 + 4,
+	.vtotal = 1280 + 16 + 4 + 4,
+
+	.type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,
+	.width_mm	= 136,
+	.height_mm	= 217,
+};
+
+static int k101_im2ba02_get_modes(struct drm_panel *panel,
+				  struct drm_connector *connector)
+{
+	struct k101_im2ba02 *ctx = panel_to_k101_im2ba02(panel);
+	struct drm_display_mode *mode;
+
+	mode = drm_mode_duplicate(connector->dev, &k101_im2ba02_default_mode);
+	if (!mode) {
+		DRM_DEV_ERROR(&ctx->dsi->dev, "failed to add mode %ux%ux@%u\n",
+			      k101_im2ba02_default_mode.hdisplay,
+			      k101_im2ba02_default_mode.vdisplay,
+			      k101_im2ba02_default_mode.vrefresh);
+		return -ENOMEM;
+	}
+
+	drm_mode_set_name(mode);
+
+	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+	connector->display_info.width_mm = mode->width_mm;
+	connector->display_info.height_mm = mode->height_mm;
+	drm_mode_probed_add(connector, mode);
+
+	return 1;
+}
+
+static const struct drm_panel_funcs k101_im2ba02_funcs = {
+	.disable = k101_im2ba02_disable,
+	.unprepare = k101_im2ba02_unprepare,
+	.prepare = k101_im2ba02_prepare,
+	.enable = k101_im2ba02_enable,
+	.get_modes = k101_im2ba02_get_modes,
+};
+
+static int k101_im2ba02_dsi_probe(struct mipi_dsi_device *dsi)
+{
+	struct k101_im2ba02 *ctx;
+	int ret;
+
+	ctx = devm_kzalloc(&dsi->dev, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+
+	mipi_dsi_set_drvdata(dsi, ctx);
+	ctx->dsi = dsi;
+
+	ctx->dvdd = devm_regulator_get(&dsi->dev, "dvdd");
+	if (IS_ERR(ctx->dvdd)) {
+		DRM_DEV_ERROR(&dsi->dev, "Couldn't get dvdd regulator\n");
+		return PTR_ERR(ctx->dvdd);
+	}
+
+	ctx->avdd = devm_regulator_get(&dsi->dev, "avdd");
+	if (IS_ERR(ctx->avdd)) {
+		DRM_DEV_ERROR(&dsi->dev, "Couldn't get avdd regulator\n");
+		return PTR_ERR(ctx->avdd);
+	}
+
+	ctx->cvdd = devm_regulator_get(&dsi->dev, "cvdd");
+	if (IS_ERR(ctx->cvdd)) {
+		DRM_DEV_ERROR(&dsi->dev, "Couldn't get cvdd regulator\n");
+		return PTR_ERR(ctx->cvdd);
+	}
+
+	ctx->reset = devm_gpiod_get(&dsi->dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->reset)) {
+		DRM_DEV_ERROR(&dsi->dev, "Couldn't get our reset GPIO\n");
+		return PTR_ERR(ctx->reset);
+	}
+
+	drm_panel_init(&ctx->panel, &dsi->dev, &k101_im2ba02_funcs,
+		       DRM_MODE_CONNECTOR_DSI);
+
+	ret = drm_panel_of_backlight(&ctx->panel);
+	if (ret)
+		return ret;
+
+	ret = drm_panel_add(&ctx->panel);
+	if (ret < 0)
+		return ret;
+
+	dsi->mode_flags = MIPI_DSI_MODE_VIDEO;
+	dsi->format = MIPI_DSI_FMT_RGB888;
+	dsi->lanes = 4;
+
+	ret = mipi_dsi_attach(dsi);
+	if (ret < 0) {
+		drm_panel_remove(&ctx->panel);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int k101_im2ba02_dsi_remove(struct mipi_dsi_device *dsi)
+{
+	struct k101_im2ba02 *ctx = mipi_dsi_get_drvdata(dsi);
+
+	mipi_dsi_detach(dsi);
+	drm_panel_remove(&ctx->panel);
+
+	return 0;
+}
+
+static const struct of_device_id k101_im2ba02_of_match[] = {
+	{ .compatible = "feixin,k101-im2ba02", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, k101_im2ba02_of_match);
+
+static struct mipi_dsi_driver k101_im2ba02_driver = {
+	.probe = k101_im2ba02_dsi_probe,
+	.remove = k101_im2ba02_dsi_remove,
+	.driver = {
+		.name = "feixin-k101-im2ba02",
+		.of_match_table = k101_im2ba02_of_match,
+	},
+};
+module_mipi_dsi_driver(k101_im2ba02_driver);
+
+MODULE_AUTHOR("Icenowy Zheng <icenowy@aosc.io>");
+MODULE_DESCRIPTION("Feixin K101 IM2BA02 MIPI-DSI LCD panel");
+MODULE_LICENSE("GPL");
-- 
2.23.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH 3/5] drm/panel: Add Feixin K101 IM2BA02 panel

[Sam Ravnborg]

Hi Icenowy.

On Fri, Jan 10, 2020 at 11:52:23PM +0800, Icenowy Zheng wrote:
> Feixin K101 IM2BA02 is a 800x1280 4-lane MIPI-DSI LCD panel.
> 
> Add a panel driver for it.
Thanks, driver looks really good.
Only a few comments/nits below.

	Sam
> 
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
>  MAINTAINERS                                   |   6 +
>  drivers/gpu/drm/panel/Kconfig                 |   9 +
>  drivers/gpu/drm/panel/Makefile                |   1 +
>  .../gpu/drm/panel/panel-feixin-k101-im2ba02.c | 548 ++++++++++++++++++
>  4 files changed, 564 insertions(+)
>  create mode 100644 drivers/gpu/drm/panel/panel-feixin-k101-im2ba02.c
> 

> new file mode 100644
> index 000000000000..45a62bdabb3f
> --- /dev/null
> +++ b/drivers/gpu/drm/panel/panel-feixin-k101-im2ba02.c
> @@ -0,0 +1,548 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2019-2020 Icenowy Zheng <icenowy@aosc.io>
> + */
> +
> +#include <linux/gpio/consumer.h>
> +#include <linux/delay.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/regulator/consumer.h>
> +
> +#include <drm/drm_mipi_dsi.h>
> +#include <drm/drm_modes.h>
> +#include <drm/drm_panel.h>
> +#include <drm/drm_print.h>
Sorted and in the right order - good.

> +
> +static int k101_im2ba02_prepare(struct drm_panel *panel)
> +{
> +	struct k101_im2ba02 *ctx = panel_to_k101_im2ba02(panel);
> +	struct mipi_dsi_device *dsi = ctx->dsi;
> +	unsigned int i;
> +	int ret;
> +
> +	ret = regulator_enable(ctx->avdd);
> +	if (ret)
> +		return ret;
> +
> +	msleep(20);
> +
> +	ret = regulator_enable(ctx->dvdd);
> +	if (ret)
> +		return ret;
> +
> +	msleep(20);
> +
> +	ret = regulator_enable(ctx->cvdd);
> +	if (ret)
> +		return ret;

Unless the msleep() between is regulator_enable() really is needed,
this change this to use regulator_bulk_enable().

If the above is kept then please do proper error handling
where all enabled regulators are disable in case of errors.

> +
> +	msleep(30);
> +
> +	gpiod_set_value(ctx->reset, 1);
> +	msleep(50);
> +
> +	gpiod_set_value(ctx->reset, 0);
> +	msleep(50);
> +
> +	gpiod_set_value(ctx->reset, 1);
> +	msleep(200);
> +
> +	for (i = 0; i < ARRAY_SIZE(k101_im2ba02_init_cmds); i++) {
> +		const struct k101_im2ba02_init_cmd *cmd = &k101_im2ba02_init_cmds[i];
> +
> +		ret = mipi_dsi_dcs_write_buffer(dsi, cmd->data, K101_IM2BA02_INIT_CMD_LEN);
> +		if (ret < 0)
> +			return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static int k101_im2ba02_enable(struct drm_panel *panel)
> +{
> +	struct k101_im2ba02 *ctx = panel_to_k101_im2ba02(panel);
> +	const struct k101_im2ba02_init_cmd *cmd = &timed_cmds[1];
> +	int ret;
> +
> +	msleep(150);
> +
> +	ret = mipi_dsi_dcs_set_display_on(ctx->dsi);
> +	if (ret < 0)
> +		return ret;
> +
> +	msleep(50);
> +
> +	return mipi_dsi_dcs_write_buffer(ctx->dsi, cmd->data, K101_IM2BA02_INIT_CMD_LEN);
> +	if (ret < 0)
> +		return ret;
The last two lines can be deleted - they are never reached.

> +}
> +
> +static int k101_im2ba02_disable(struct drm_panel *panel)
> +{
> +	struct k101_im2ba02 *ctx = panel_to_k101_im2ba02(panel);
> +
> +	return mipi_dsi_dcs_set_display_off(ctx->dsi);
> +}
> +
> +static int k101_im2ba02_unprepare(struct drm_panel *panel)
> +{
> +	struct k101_im2ba02 *ctx = panel_to_k101_im2ba02(panel);
> +	int ret;
> +
> +	ret = mipi_dsi_dcs_set_display_off(ctx->dsi);
> +	if (ret < 0)
> +		DRM_DEV_ERROR(panel->dev, "failed to set display off: %d\n",
> +			      ret);
> +
> +	ret = mipi_dsi_dcs_enter_sleep_mode(ctx->dsi);
> +	if (ret < 0)
> +		DRM_DEV_ERROR(panel->dev, "failed to enter sleep mode: %d\n",
> +			      ret);
> +
> +	msleep(200);
> +
> +	gpiod_set_value(ctx->reset, 0);
> +
> +	msleep(20);
> +
> +	regulator_disable(ctx->cvdd);
> +
> +	msleep(20);
> +
> +	regulator_disable(ctx->dvdd);
> +
> +	msleep(20);
> +
> +	regulator_disable(ctx->avdd);
Can we get rid of a few empty lines here?
If the 20 msecs are not really needed then use regulator_bulk_disable()


> +	return 0;
> +}
> +
> +static const struct drm_display_mode k101_im2ba02_default_mode = {
> +	.clock = 70000,
> +	.vrefresh = 60,
> +
> +	.hdisplay = 800,
> +	.hsync_start = 800 + 20,
> +	.hsync_end = 800 + 20 + 20,
> +	.htotal = 800 + 20 + 20 + 20,
> +
> +	.vdisplay = 1280,
> +	.vsync_start = 1280 + 16,
> +	.vsync_end = 1280 + 16 + 4,
> +	.vtotal = 1280 + 16 + 4 + 4,
> +
> +	.type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,
> +	.width_mm	= 136,
> +	.height_mm	= 217,
> +};
> +
> +static int k101_im2ba02_get_modes(struct drm_panel *panel,
> +				  struct drm_connector *connector)
> +{
> +	struct k101_im2ba02 *ctx = panel_to_k101_im2ba02(panel);
> +	struct drm_display_mode *mode;
> +
> +	mode = drm_mode_duplicate(connector->dev, &k101_im2ba02_default_mode);
> +	if (!mode) {
> +		DRM_DEV_ERROR(&ctx->dsi->dev, "failed to add mode %ux%ux@%u\n",
> +			      k101_im2ba02_default_mode.hdisplay,
> +			      k101_im2ba02_default_mode.vdisplay,
> +			      k101_im2ba02_default_mode.vrefresh);
> +		return -ENOMEM;
> +	}
> +
> +	drm_mode_set_name(mode);
> +
> +	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
> +	connector->display_info.width_mm = mode->width_mm;
> +	connector->display_info.height_mm = mode->height_mm;
> +	drm_mode_probed_add(connector, mode);
> +
> +	return 1;
> +}
> +
> +static const struct drm_panel_funcs k101_im2ba02_funcs = {
> +	.disable = k101_im2ba02_disable,
> +	.unprepare = k101_im2ba02_unprepare,
> +	.prepare = k101_im2ba02_prepare,
> +	.enable = k101_im2ba02_enable,
> +	.get_modes = k101_im2ba02_get_modes,
> +};
> +
> +static int k101_im2ba02_dsi_probe(struct mipi_dsi_device *dsi)
> +{
> +	struct k101_im2ba02 *ctx;
> +	int ret;
> +
> +	ctx = devm_kzalloc(&dsi->dev, sizeof(*ctx), GFP_KERNEL);
> +	if (!ctx)
> +		return -ENOMEM;
> +
> +	mipi_dsi_set_drvdata(dsi, ctx);
> +	ctx->dsi = dsi;
> +
> +	ctx->dvdd = devm_regulator_get(&dsi->dev, "dvdd");
> +	if (IS_ERR(ctx->dvdd)) {
> +		DRM_DEV_ERROR(&dsi->dev, "Couldn't get dvdd regulator\n");
> +		return PTR_ERR(ctx->dvdd);
> +	}
> +
> +	ctx->avdd = devm_regulator_get(&dsi->dev, "avdd");
> +	if (IS_ERR(ctx->avdd)) {
> +		DRM_DEV_ERROR(&dsi->dev, "Couldn't get avdd regulator\n");
> +		return PTR_ERR(ctx->avdd);
> +	}
> +
> +	ctx->cvdd = devm_regulator_get(&dsi->dev, "cvdd");
> +	if (IS_ERR(ctx->cvdd)) {
> +		DRM_DEV_ERROR(&dsi->dev, "Couldn't get cvdd regulator\n");
> +		return PTR_ERR(ctx->cvdd);
> +	}
> +
> +	ctx->reset = devm_gpiod_get(&dsi->dev, "reset", GPIOD_OUT_LOW);
> +	if (IS_ERR(ctx->reset)) {
> +		DRM_DEV_ERROR(&dsi->dev, "Couldn't get our reset GPIO\n");
> +		return PTR_ERR(ctx->reset);
> +	}
> +
> +	drm_panel_init(&ctx->panel, &dsi->dev, &k101_im2ba02_funcs,
> +		       DRM_MODE_CONNECTOR_DSI);
> +
> +	ret = drm_panel_of_backlight(&ctx->panel);
> +	if (ret)
> +		return ret;
> +
> +	ret = drm_panel_add(&ctx->panel);
> +	if (ret < 0)
> +		return ret;
> +
> +	dsi->mode_flags = MIPI_DSI_MODE_VIDEO;
> +	dsi->format = MIPI_DSI_FMT_RGB888;
> +	dsi->lanes = 4;
> +
> +	ret = mipi_dsi_attach(dsi);
> +	if (ret < 0) {
> +		drm_panel_remove(&ctx->panel);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static int k101_im2ba02_dsi_remove(struct mipi_dsi_device *dsi)
> +{
> +	struct k101_im2ba02 *ctx = mipi_dsi_get_drvdata(dsi);
> +
> +	mipi_dsi_detach(dsi);
> +	drm_panel_remove(&ctx->panel);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id k101_im2ba02_of_match[] = {
> +	{ .compatible = "feixin,k101-im2ba02", },
> +	{ }
Use { /* sentinel */ },

> +};
> +MODULE_DEVICE_TABLE(of, k101_im2ba02_of_match);
> +
> +static struct mipi_dsi_driver k101_im2ba02_driver = {
> +	.probe = k101_im2ba02_dsi_probe,
> +	.remove = k101_im2ba02_dsi_remove,
> +	.driver = {
> +		.name = "feixin-k101-im2ba02",
> +		.of_match_table = k101_im2ba02_of_match,
> +	},
> +};
> +module_mipi_dsi_driver(k101_im2ba02_driver);
> +
> +MODULE_AUTHOR("Icenowy Zheng <icenowy@aosc.io>");
> +MODULE_DESCRIPTION("Feixin K101 IM2BA02 MIPI-DSI LCD panel");
> +MODULE_LICENSE("GPL");
> -- 
> 2.23.0
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH 4/5] dt-bindings: arm: sunxi: add binding for PineTab tablet

[Icenowy Zheng]

Add the device tree binding for Pine64's PineTab tablet, which uses
Allwinner A64 SoC.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
 Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
index 327ce6730823..159060b65c5d 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -636,6 +636,11 @@ properties:
           - const: pine64,pinebook
           - const: allwinner,sun50i-a64
 
+      - description: Pine64 PineTab
+        items:
+          - const: pine64,pinetab
+          - const: allwinner,sun50i-a64
+
       - description: Pine64 SoPine Baseboard
         items:
           - const: pine64,sopine-baseboard
-- 
2.23.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH 4/5] dt-bindings: arm: sunxi: add binding for PineTab tablet

[Rob Herring]

On Fri, 10 Jan 2020 23:52:24 +0800, Icenowy Zheng wrote:
> Add the device tree binding for Pine64's PineTab tablet, which uses
> Allwinner A64 SoC.
> 
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
>  Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
>  1 file changed, 5 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH 5/5] arm64: dts: allwinner: a64: add support for PineTab

[Icenowy Zheng]

PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.

It includes the following peripherals:

USB:
- A microUSB Type-B port connected to the OTG-capable USB PHY of
Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the
Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG
functionality on this port.
- A USB Type-A port is connected to the internal hub attached to the
non-OTG USB PHY of Allwinner A64.
- There are reserved pins for an external keyboard connected to the
internal hub.

Power:
- The microUSB port has its Vbus connected to AXP803, mentioned above.
- A DC jack (of a strange size, 2.5mm outer diameter) is connected to
the ACIN of AXP803.
- A Li-Polymer battery is connected to the battery pins of AXP803.

Storage:
- An tradition Pine64 eMMC slot is on the board, mounted with an eMMC
module by factory.
- An external microSD slot is hidden under a protect case.

Display:
- A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC.
- A mini HDMI port.

Input:
- A touch panel attached to a Goodix GT9271 touch controller.
- Volume keys connected to the LRADC of the A64 SoC.

Camera:
- An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC.
- A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640.

Audio:
- A headphone jack is conencted to the SoC's internal codec.
- A speaker connected is to the Line Out port of SoC's internal codec, via
an amplifier.

Misc:
- Debug UART is muxed with the headphone jack, with the switch next to
the microSD slot.
- A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC.
- Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the
one in Pinebook.

This commit adds a basically usable device tree for it, implementing
most of the features mentioned above. HDMI is not supported now because
bad LCD-HDMI coexistence situation of mainline A64 display driver, and
the front camera currently lacks a driver and a facility to share the
bus with the rear one.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../boot/dts/allwinner/sun50i-a64-pinetab.dts | 461 ++++++++++++++++++
 2 files changed, 462 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index cf4f78617c3f..6dad63881cd3 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-lts.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
new file mode 100644
index 000000000000..1dfa3668636e
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
@@ -0,0 +1,461 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ */
+
+/dts-v1/;
+
+#include "sun50i-a64.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "PineTab";
+	compatible = "pine64,pinetab", "allwinner,sun50i-a64";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &rtl8723cs;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */
+		power-supply = <&vdd_bl>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	i2c-csi {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 4 13 GPIO_ACTIVE_HIGH>; /* PE13 */
+		scl-gpios = <&pio 4 12 GPIO_ACTIVE_HIGH>; /* PE12 */
+		i2c-gpio,delay-us = <5>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Rear camera */
+		ov5640: camera@3c {
+			compatible = "ovti,ov5640";
+			reg = <0x3c>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&csi_mclk_pin>;
+			clocks = <&ccu CLK_CSI_MCLK>;
+			clock-names = "xclk";
+
+			AVDD-supply = <&reg_dldo3>;
+			DOVDD-supply = <&reg_aldo1>;
+			DVDD-supply = <&reg_eldo3>;
+			reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>; /* PE14 */
+			powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */
+
+			port {
+				ov5640_ep: endpoint {
+					remote-endpoint = <&csi_ep>;
+					bus-width = <8>;
+					hsync-active = <1>; /* Active high */
+					vsync-active = <0>; /* Active low */
+					data-active = <1>;  /* Active high */
+					pclk-sample = <1>;  /* Rising */
+				};
+			};
+		};
+	};
+
+	speaker_amp: audio-amplifier {
+		compatible = "simple-audio-amplifier";
+		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+		sound-name-prefix = "Speaker Amp";
+	};
+
+	vdd_bl: regulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "bl-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+		enable-active-high;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&codec {
+	status = "okay";
+};
+
+&codec_analog {
+	hpvcc-supply = <&reg_eldo1>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&csi {
+	status = "okay";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		csi_ep: endpoint {
+			remote-endpoint = <&ov5640_ep>;
+			bus-width = <8>;
+			hsync-active = <1>; /* Active high */
+			vsync-active = <0>; /* Active low */
+			data-active = <1>;  /* Active high */
+			pclk-sample = <1>;  /* Rising */
+		};
+	};
+};
+
+&dai {
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&dphy {
+	status = "okay";
+};
+
+&dsi {
+	vcc-dsi-supply = <&reg_dldo1>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	panel@0 {
+		compatible = "feixin,k101-im2ba02";
+		reg = <0>;
+		avdd-supply = <&reg_dc1sw>;
+		dvdd-supply = <&reg_dc1sw>;
+		cvdd-supply = <&reg_ldo_io1>;
+		reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+		backlight = <&backlight>;
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+
+	touchscreen@5d {
+		compatible = "goodix,gt9271";
+		reg = <0x5d>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */
+		irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+		reset-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+		AVDD28-supply = <&reg_ldo_io1>;
+	};
+};
+
+&i2c0_pins {
+	bias-pull-up;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	status = "okay";
+
+	bma223@18 {
+		compatible = "bosch,bma223", "bosch,bma222e";
+		reg = <0x18>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 5 IRQ_TYPE_LEVEL_HIGH>; /* PH5 */
+		mount-matrix = "0", "-1", "0",
+			       "-1", "0", "0",
+			       "0", "0", "-1";
+	};
+};
+
+&lradc {
+	vref-supply = <&reg_aldo3>;
+	status = "okay";
+
+	button-200 {
+		label = "Volume Up";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <200000>;
+	};
+
+	button-400 {
+		label = "Volume Down";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <400000>;
+	};
+};
+
+&mixer1 {
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_dldo4>;
+	vqmmc-supply = <&reg_eldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	rtl8723cs: wifi@1 {
+		reg = <1>;
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_dcdc1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pwm {
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		x-powers,drive-vbus-en;
+	};
+};
+
+#include "axp803.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&reg_aldo1 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "dovdd-csi";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <2700000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc1sw {
+	regulator-name = "vcc-lcd";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi-dsi-sensor";
+};
+
+&reg_dldo3 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "avdd-csi";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
+&reg_eldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "cpvdd";
+};
+
+&reg_eldo2 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcca-1v8";
+};
+
+&reg_eldo3 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "dvdd-1v8-csi";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_ldo_io0 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-usb";
+	status = "okay";
+};
+
+&reg_ldo_io1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-enable-ramp-delay = <3500000>;
+	regulator-name = "vcc-touchscreen";
+	status = "okay";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
+&sound {
+	status = "okay";
+	simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>;
+	simple-audio-card,widgets = "Microphone", "Internal Microphone Left",
+				    "Microphone", "Internal Microphone Right",
+				    "Headphone", "Headphone Jack",
+				    "Speaker", "Internal Speaker";
+	simple-audio-card,routing =
+			"Left DAC", "AIF1 Slot 0 Left",
+			"Right DAC", "AIF1 Slot 0 Right",
+			"Speaker Amp INL", "LINEOUT",
+			"Speaker Amp INR", "LINEOUT",
+			"Internal Speaker", "Speaker Amp OUTL",
+			"Internal Speaker", "Speaker Amp OUTR",
+			"Headphone Jack", "HP",
+			"AIF1 Slot 0 Left ADC", "Left ADC",
+			"AIF1 Slot 0 Right ADC", "Right ADC",
+			"Internal Microphone Left", "MBIAS",
+			"MIC1", "Internal Microphone Left",
+			"Internal Microphone Right", "HBIAS",
+			"MIC2", "Internal Microphone Right";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+	usb0_vbus_power-supply = <&usb_power_supply>;
+	usb0_vbus-supply = <&reg_drivevbus>;
+	usb1_vbus-supply = <&reg_ldo_io0>;
+	status = "okay";
+};
-- 
2.23.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH 5/5] arm64: dts: allwinner: a64: add support for PineTab

[Maxime Ripard]

[-- Attachment #1.1: Type: text/plain, Size: 6826 bytes --]

Hi,

On Fri, Jan 10, 2020 at 11:52:25PM +0800, Icenowy Zheng wrote:
> PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.
>
> It includes the following peripherals:
>
> USB:
> - A microUSB Type-B port connected to the OTG-capable USB PHY of
> Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the
> Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG
> functionality on this port.
> - A USB Type-A port is connected to the internal hub attached to the
> non-OTG USB PHY of Allwinner A64.
> - There are reserved pins for an external keyboard connected to the
> internal hub.
>
> Power:
> - The microUSB port has its Vbus connected to AXP803, mentioned above.
> - A DC jack (of a strange size, 2.5mm outer diameter) is connected to
> the ACIN of AXP803.
> - A Li-Polymer battery is connected to the battery pins of AXP803.
>
> Storage:
> - An tradition Pine64 eMMC slot is on the board, mounted with an eMMC
> module by factory.
> - An external microSD slot is hidden under a protect case.
>
> Display:
> - A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC.
> - A mini HDMI port.
>
> Input:
> - A touch panel attached to a Goodix GT9271 touch controller.
> - Volume keys connected to the LRADC of the A64 SoC.
>
> Camera:
> - An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC.
> - A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640.
>
> Audio:
> - A headphone jack is conencted to the SoC's internal codec.
> - A speaker connected is to the Line Out port of SoC's internal codec, via
> an amplifier.
>
> Misc:
> - Debug UART is muxed with the headphone jack, with the switch next to
> the microSD slot.
> - A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC.
> - Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the
> one in Pinebook.
>
> This commit adds a basically usable device tree for it, implementing
> most of the features mentioned above. HDMI is not supported now because
> bad LCD-HDMI coexistence situation of mainline A64 display driver, and
> the front camera currently lacks a driver and a facility to share the
> bus with the rear one.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
>  arch/arm64/boot/dts/allwinner/Makefile        |   1 +
>  .../boot/dts/allwinner/sun50i-a64-pinetab.dts | 461 ++++++++++++++++++
>  2 files changed, 462 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
>
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index cf4f78617c3f..6dad63881cd3 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-lts.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
> new file mode 100644
> index 000000000000..1dfa3668636e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
> @@ -0,0 +1,461 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.xyz>
> + *
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-a64.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/pwm/pwm.h>
> +
> +/ {
> +	model = "PineTab";
> +	compatible = "pine64,pinetab", "allwinner,sun50i-a64";
> +
> +	aliases {
> +		serial0 = &uart0;
> +		ethernet0 = &rtl8723cs;
> +	};
> +
> +	backlight: backlight {
> +		compatible = "pwm-backlight";
> +		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
> +		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;

Each step should be a perceived step, not a decimal one. So let's say,
if you have 10 steps, each step should be seen as a 10% increase in
brightness. Usually a quadratic increase works better there.

> +&dsi {
> +	vcc-dsi-supply = <&reg_dldo1>;
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	status = "okay";

address-cells and size-cells aren't in the DTSI? They should be.

> +
> +	panel@0 {
> +		compatible = "feixin,k101-im2ba02";
> +		reg = <0>;
> +		avdd-supply = <&reg_dc1sw>;
> +		dvdd-supply = <&reg_dc1sw>;
> +		cvdd-supply = <&reg_ldo_io1>;
> +		reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
> +		backlight = <&backlight>;
> +	};
> +};
> +
> +&ehci0 {
> +	status = "okay";
> +};
> +
> +&ehci1 {
> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c0_pins>;

That should be set in the DTSI already?

> +	status = "okay";
> +
> +	touchscreen@5d {
> +		compatible = "goodix,gt9271";
> +		reg = <0x5d>;
> +		interrupt-parent = <&pio>;
> +		interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */
> +		irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
> +		reset-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
> +		AVDD28-supply = <&reg_ldo_io1>;
> +	};
> +};
> +
> +&i2c0_pins {
> +	bias-pull-up;
> +};
> +
> +&i2c1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c1_pins>;

Ditto

> +	status = "okay";
> +
> +	bma223@18 {
> +		compatible = "bosch,bma223", "bosch,bma222e";
> +		reg = <0x18>;
> +		interrupt-parent = <&pio>;
> +		interrupts = <7 5 IRQ_TYPE_LEVEL_HIGH>; /* PH5 */
> +		mount-matrix = "0", "-1", "0",
> +			       "-1", "0", "0",
> +			       "0", "0", "-1";
> +	};
> +};
> +
> +&lradc {
> +	vref-supply = <&reg_aldo3>;
> +	status = "okay";
> +
> +	button-200 {
> +		label = "Volume Up";
> +		linux,code = <KEY_VOLUMEUP>;
> +		channel = <0>;
> +		voltage = <200000>;
> +	};
> +
> +	button-400 {
> +		label = "Volume Down";
> +		linux,code = <KEY_VOLUMEDOWN>;
> +		channel = <0>;
> +		voltage = <400000>;
> +	};
> +};
> +
> +&mixer1 {
> +	status = "okay";
> +};
> +
> +&mmc0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc0_pins>;

Ditto

> +	vmmc-supply = <&reg_dcdc1>;
> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> +	disable-wp;
> +	bus-width = <4>;
> +	status = "okay";
> +};
> +
> +&mmc1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc1_pins>;

Ditto

> +	vmmc-supply = <&reg_dldo4>;
> +	vqmmc-supply = <&reg_eldo1>;
> +	mmc-pwrseq = <&wifi_pwrseq>;
> +	bus-width = <4>;
> +	non-removable;
> +	status = "okay";
> +
> +	rtl8723cs: wifi@1 {
> +		reg = <1>;
> +	};
> +};
> +
> +&mmc2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc2_pins>;

Ditto

Looks good otherwise, thanks!
Maxime

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 160 bytes --]

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH 5/5] arm64: dts: allwinner: a64: add support for PineTab

[Sam Ravnborg]

Hi Icenowy.

checkpatch noticed a small inconsistency in the i2c1 node.

> 
> Misc:
> - Debug UART is muxed with the headphone jack, with the switch next to
> the microSD slot.
> - A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC.
> - Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the
> one in Pinebook.
> 
> +
> +&i2c1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c1_pins>;
> +	status = "okay";
> +
> +	bma223@18 {
> +		compatible = "bosch,bma223", "bosch,bma222e";
These compatible have no binding file?!?


> +		reg = <0x18>;
> +		interrupt-parent = <&pio>;
> +		interrupts = <7 5 IRQ_TYPE_LEVEL_HIGH>; /* PH5 */
> +		mount-matrix = "0", "-1", "0",
> +			       "-1", "0", "0",
> +			       "0", "0", "-1";
> +	};
> +};

bosch,bma222e is referenced by a driver, whereas this is the
first reference of bosch,bma223.

	Sam
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [linux-sunxi] [PATCH 5/5] arm64: dts: allwinner: a64: add support for PineTab

[Vasily Khoruzhick]

On Fri, Jan 10, 2020 at 7:54 AM Icenowy Zheng <icenowy@aosc.io> wrote:
>
> PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.
>
> It includes the following peripherals:
>
> USB:
> - A microUSB Type-B port connected to the OTG-capable USB PHY of
> Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the
> Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG
> functionality on this port.
> - A USB Type-A port is connected to the internal hub attached to the
> non-OTG USB PHY of Allwinner A64.
> - There are reserved pins for an external keyboard connected to the
> internal hub.
>
> Power:
> - The microUSB port has its Vbus connected to AXP803, mentioned above.
> - A DC jack (of a strange size, 2.5mm outer diameter) is connected to
> the ACIN of AXP803.
> - A Li-Polymer battery is connected to the battery pins of AXP803.
>
> Storage:
> - An tradition Pine64 eMMC slot is on the board, mounted with an eMMC
> module by factory.
> - An external microSD slot is hidden under a protect case.
>
> Display:
> - A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC.
> - A mini HDMI port.
>
> Input:
> - A touch panel attached to a Goodix GT9271 touch controller.
> - Volume keys connected to the LRADC of the A64 SoC.
>
> Camera:
> - An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC.
> - A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640.
>
> Audio:
> - A headphone jack is conencted to the SoC's internal codec.
> - A speaker connected is to the Line Out port of SoC's internal codec, via
> an amplifier.
>
> Misc:
> - Debug UART is muxed with the headphone jack, with the switch next to
> the microSD slot.
> - A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC.
> - Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the
> one in Pinebook.
>
> This commit adds a basically usable device tree for it, implementing
> most of the features mentioned above. HDMI is not supported now because
> bad LCD-HDMI coexistence situation of mainline A64 display driver, and
> the front camera currently lacks a driver and a facility to share the
> bus with the rear one.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
>  arch/arm64/boot/dts/allwinner/Makefile        |   1 +
>  .../boot/dts/allwinner/sun50i-a64-pinetab.dts | 461 ++++++++++++++++++
>  2 files changed, 462 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
>
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index cf4f78617c3f..6dad63881cd3 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-lts.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
> new file mode 100644
> index 000000000000..1dfa3668636e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
> @@ -0,0 +1,461 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.xyz>
> + *
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-a64.dtsi"

You may want to include dtsi with OPP for A64 here if you want to enable DVFS

> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/pwm/pwm.h>
> +
> +/ {
> +       model = "PineTab";
> +       compatible = "pine64,pinetab", "allwinner,sun50i-a64";
> +
> +       aliases {
> +               serial0 = &uart0;
> +               ethernet0 = &rtl8723cs;
> +       };
> +
> +       backlight: backlight {
> +               compatible = "pwm-backlight";
> +               pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
> +               brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
> +               default-brightness-level = <8>;
> +               enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */
> +               power-supply = <&vdd_bl>;
> +       };
> +
> +       chosen {
> +               stdout-path = "serial0:115200n8";
> +       };
> +
> +       i2c-csi {
> +               compatible = "i2c-gpio";
> +               sda-gpios = <&pio 4 13 GPIO_ACTIVE_HIGH>; /* PE13 */
> +               scl-gpios = <&pio 4 12 GPIO_ACTIVE_HIGH>; /* PE12 */
> +               i2c-gpio,delay-us = <5>;
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               /* Rear camera */
> +               ov5640: camera@3c {
> +                       compatible = "ovti,ov5640";
> +                       reg = <0x3c>;
> +                       pinctrl-names = "default";
> +                       pinctrl-0 = <&csi_mclk_pin>;
> +                       clocks = <&ccu CLK_CSI_MCLK>;
> +                       clock-names = "xclk";
> +
> +                       AVDD-supply = <&reg_dldo3>;
> +                       DOVDD-supply = <&reg_aldo1>;
> +                       DVDD-supply = <&reg_eldo3>;
> +                       reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>; /* PE14 */
> +                       powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */
> +
> +                       port {
> +                               ov5640_ep: endpoint {
> +                                       remote-endpoint = <&csi_ep>;
> +                                       bus-width = <8>;
> +                                       hsync-active = <1>; /* Active high */
> +                                       vsync-active = <0>; /* Active low */
> +                                       data-active = <1>;  /* Active high */
> +                                       pclk-sample = <1>;  /* Rising */
> +                               };
> +                       };
> +               };
> +       };
> +
> +       speaker_amp: audio-amplifier {
> +               compatible = "simple-audio-amplifier";
> +               enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
> +               sound-name-prefix = "Speaker Amp";
> +       };
> +
> +       vdd_bl: regulator@0 {
> +               compatible = "regulator-fixed";
> +               regulator-name = "bl-3v3";
> +               regulator-min-microvolt = <3300000>;
> +               regulator-max-microvolt = <3300000>;
> +               gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
> +               enable-active-high;
> +       };
> +
> +       wifi_pwrseq: wifi_pwrseq {
> +               compatible = "mmc-pwrseq-simple";
> +               reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
> +               post-power-on-delay-ms = <200>;
> +       };
> +};
> +
> +&codec {
> +       status = "okay";
> +};
> +
> +&codec_analog {
> +       hpvcc-supply = <&reg_eldo1>;
> +       status = "okay";
> +};
> +
> +&cpu0 {
> +       cpu-supply = <&reg_dcdc2>;
> +};

I believe you need CPU regulator for each CPU. I'm aware that we share
clock and regulator for all the CPUs but what would happen if you put
CPU0 offline?

> +
> +&csi {
> +       status = "okay";
> +
> +       port {
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               csi_ep: endpoint {
> +                       remote-endpoint = <&ov5640_ep>;
> +                       bus-width = <8>;
> +                       hsync-active = <1>; /* Active high */
> +                       vsync-active = <0>; /* Active low */
> +                       data-active = <1>;  /* Active high */
> +                       pclk-sample = <1>;  /* Rising */
> +               };
> +       };
> +};
> +
> +&dai {
> +       status = "okay";
> +};
> +
> +&de {
> +       status = "okay";
> +};
> +
> +&dphy {
> +       status = "okay";
> +};
> +
> +&dsi {
> +       vcc-dsi-supply = <&reg_dldo1>;
> +       #address-cells = <1>;
> +       #size-cells = <0>;
> +       status = "okay";
> +
> +       panel@0 {
> +               compatible = "feixin,k101-im2ba02";
> +               reg = <0>;
> +               avdd-supply = <&reg_dc1sw>;
> +               dvdd-supply = <&reg_dc1sw>;
> +               cvdd-supply = <&reg_ldo_io1>;
> +               reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
> +               backlight = <&backlight>;
> +       };
> +};
> +
> +&ehci0 {
> +       status = "okay";
> +};
> +
> +&ehci1 {
> +       status = "okay";
> +};
> +
> +&i2c0 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&i2c0_pins>;
> +       status = "okay";
> +
> +       touchscreen@5d {
> +               compatible = "goodix,gt9271";
> +               reg = <0x5d>;
> +               interrupt-parent = <&pio>;
> +               interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */
> +               irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
> +               reset-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
> +               AVDD28-supply = <&reg_ldo_io1>;
> +       };
> +};
> +
> +&i2c0_pins {
> +       bias-pull-up;
> +};
> +
> +&i2c1 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&i2c1_pins>;
> +       status = "okay";
> +
> +       bma223@18 {
> +               compatible = "bosch,bma223", "bosch,bma222e";
> +               reg = <0x18>;
> +               interrupt-parent = <&pio>;
> +               interrupts = <7 5 IRQ_TYPE_LEVEL_HIGH>; /* PH5 */
> +               mount-matrix = "0", "-1", "0",
> +                              "-1", "0", "0",
> +                              "0", "0", "-1";
> +       };
> +};
> +
> +&lradc {
> +       vref-supply = <&reg_aldo3>;
> +       status = "okay";
> +
> +       button-200 {
> +               label = "Volume Up";
> +               linux,code = <KEY_VOLUMEUP>;
> +               channel = <0>;
> +               voltage = <200000>;
> +       };
> +
> +       button-400 {
> +               label = "Volume Down";
> +               linux,code = <KEY_VOLUMEDOWN>;
> +               channel = <0>;
> +               voltage = <400000>;
> +       };
> +};
> +
> +&mixer1 {
> +       status = "okay";
> +};
> +
> +&mmc0 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&mmc0_pins>;
> +       vmmc-supply = <&reg_dcdc1>;
> +       cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> +       disable-wp;
> +       bus-width = <4>;
> +       status = "okay";
> +};
> +
> +&mmc1 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&mmc1_pins>;
> +       vmmc-supply = <&reg_dldo4>;
> +       vqmmc-supply = <&reg_eldo1>;
> +       mmc-pwrseq = <&wifi_pwrseq>;
> +       bus-width = <4>;
> +       non-removable;
> +       status = "okay";
> +
> +       rtl8723cs: wifi@1 {
> +               reg = <1>;
> +       };
> +};
> +
> +&mmc2 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&mmc2_pins>;
> +       vmmc-supply = <&reg_dcdc1>;
> +       vqmmc-supply = <&reg_dcdc1>;
> +       bus-width = <8>;
> +       non-removable;
> +       cap-mmc-hw-reset;
> +       status = "okay";
> +};
> +
> +&ohci0 {
> +       status = "okay";
> +};
> +
> +&pwm {
> +       status = "okay";
> +};
> +
> +&r_rsb {
> +       status = "okay";
> +
> +       axp803: pmic@3a3 {
> +               compatible = "x-powers,axp803";
> +               reg = <0x3a3>;
> +               interrupt-parent = <&r_intc>;
> +               interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> +               x-powers,drive-vbus-en;
> +       };
> +};
> +
> +#include "axp803.dtsi"
> +
> +&ac_power_supply {
> +       status = "okay";
> +};
> +
> +&battery_power_supply {
> +       status = "okay";
> +};
> +
> +&reg_aldo1 {
> +       regulator-min-microvolt = <2800000>;
> +       regulator-max-microvolt = <2800000>;
> +       regulator-name = "dovdd-csi";
> +};
> +
> +&reg_aldo2 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <1800000>;
> +       regulator-max-microvolt = <3300000>;
> +       regulator-name = "vcc-pl";
> +};
> +
> +&reg_aldo3 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <2700000>;
> +       regulator-max-microvolt = <3300000>;
> +       regulator-name = "vcc-pll-avcc";
> +};
> +
> +&reg_dc1sw {
> +       regulator-name = "vcc-lcd";
> +};
> +
> +&reg_dcdc1 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <3300000>;
> +       regulator-max-microvolt = <3300000>;
> +       regulator-name = "vcc-3v3";
> +};
> +
> +&reg_dcdc2 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <1000000>;
> +       regulator-max-microvolt = <1300000>;
> +       regulator-name = "vdd-cpux";
> +};
> +
> +/* DCDC3 is polyphased with DCDC2 */
> +
> +&reg_dcdc5 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <1200000>;
> +       regulator-max-microvolt = <1200000>;
> +       regulator-name = "vcc-dram";
> +};
> +
> +&reg_dcdc6 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <1100000>;
> +       regulator-max-microvolt = <1100000>;
> +       regulator-name = "vdd-sys";
> +};
> +
> +&reg_dldo1 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <3300000>;
> +       regulator-max-microvolt = <3300000>;
> +       regulator-name = "vcc-hdmi-dsi-sensor";
> +};
> +
> +&reg_dldo3 {
> +       regulator-min-microvolt = <2800000>;
> +       regulator-max-microvolt = <2800000>;
> +       regulator-name = "avdd-csi";
> +};
> +
> +&reg_dldo4 {
> +       regulator-min-microvolt = <3300000>;
> +       regulator-max-microvolt = <3300000>;
> +       regulator-name = "vcc-wifi";
> +};
> +
> +&reg_drivevbus {
> +       regulator-name = "usb0-vbus";
> +       status = "okay";
> +};
> +
> +&reg_eldo1 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <1800000>;
> +       regulator-max-microvolt = <1800000>;
> +       regulator-name = "cpvdd";
> +};
> +
> +&reg_eldo2 {
> +       regulator-min-microvolt = <1800000>;
> +       regulator-max-microvolt = <1800000>;
> +       regulator-name = "vcca-1v8";
> +};
> +
> +&reg_eldo3 {
> +       regulator-min-microvolt = <1800000>;
> +       regulator-max-microvolt = <1800000>;
> +       regulator-name = "dvdd-1v8-csi";
> +};
> +
> +&reg_fldo1 {
> +       regulator-min-microvolt = <1200000>;
> +       regulator-max-microvolt = <1200000>;
> +       regulator-name = "vcc-1v2-hsic";
> +};
> +
> +&reg_fldo2 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <1100000>;
> +       regulator-max-microvolt = <1100000>;
> +       regulator-name = "vdd-cpus";
> +};
> +
> +&reg_ldo_io0 {
> +       regulator-min-microvolt = <3300000>;
> +       regulator-max-microvolt = <3300000>;
> +       regulator-name = "vcc-usb";
> +       status = "okay";
> +};
> +
> +&reg_ldo_io1 {
> +       regulator-min-microvolt = <3300000>;
> +       regulator-max-microvolt = <3300000>;
> +       regulator-enable-ramp-delay = <3500000>;
> +       regulator-name = "vcc-touchscreen";
> +       status = "okay";
> +};
> +
> +&reg_rtc_ldo {
> +       regulator-name = "vcc-rtc";
> +};
> +
> +&sound {
> +       status = "okay";
> +       simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>;
> +       simple-audio-card,widgets = "Microphone", "Internal Microphone Left",
> +                                   "Microphone", "Internal Microphone Right",
> +                                   "Headphone", "Headphone Jack",
> +                                   "Speaker", "Internal Speaker";
> +       simple-audio-card,routing =
> +                       "Left DAC", "AIF1 Slot 0 Left",
> +                       "Right DAC", "AIF1 Slot 0 Right",
> +                       "Speaker Amp INL", "LINEOUT",
> +                       "Speaker Amp INR", "LINEOUT",
> +                       "Internal Speaker", "Speaker Amp OUTL",
> +                       "Internal Speaker", "Speaker Amp OUTR",
> +                       "Headphone Jack", "HP",
> +                       "AIF1 Slot 0 Left ADC", "Left ADC",
> +                       "AIF1 Slot 0 Right ADC", "Right ADC",
> +                       "Internal Microphone Left", "MBIAS",
> +                       "MIC1", "Internal Microphone Left",
> +                       "Internal Microphone Right", "HBIAS",
> +                       "MIC2", "Internal Microphone Right";
> +};
> +
> +&uart0 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&uart0_pb_pins>;
> +       status = "okay";
> +};
> +
> +&usb_otg {
> +       dr_mode = "otg";
> +       status = "okay";
> +};
> +
> +&usb_power_supply {
> +       status = "okay";
> +};
> +
> +&usbphy {
> +       usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
> +       usb0_vbus_power-supply = <&usb_power_supply>;
> +       usb0_vbus-supply = <&reg_drivevbus>;
> +       usb1_vbus-supply = <&reg_ldo_io0>;
> +       status = "okay";
> +};
> --
> 2.23.0
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
> To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20200110155225.1051749-6-icenowy%40aosc.io.
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel