[v4] arm64: dts: sc7180: add nodes for idp display

[v4] arm64: dts: sc7180: add nodes for idp display

[Harigovindan P]

Add nodes for IDP display. The display is Visionox RM69299.

Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
---
Changes in v2:
	- Adding dependency patchwork series
	- Removing suspend configuration
	- Adding blank before space curly brace
Changes in v3:
	- Updating status for mdp and mdss node to get the
	display working
	- Change in commit text
Changes in v4:
	- Added pinconf subnode
	- Using macros for function and drive-strength

 arch/arm64/boot/dts/qcom/sc7180-idp.dts | 65 +++++++++++++++++++++++++
 1 file changed, 65 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index 39dbfc89689e..5e0b7e4b2545 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -9,6 +9,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include "sc7180.dtsi"
 #include "pm6150.dtsi"
 #include "pm6150l.dtsi"
@@ -287,6 +288,57 @@ vreg_bob: bob {
 	};
 };
 
+&dsi0 {
+	status = "okay";
+
+	vdda-supply = <&vreg_l3c_1p2>;
+
+	panel@0 {
+		compatible = "visionox,rm69299-1080p-display";
+		reg = <0>;
+
+		vdda-supply = <&vreg_l8c_1p8>;
+		vdd3p3-supply = <&vreg_l18a_2p8>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&disp_pins>;
+
+		reset-gpios = <&pm6150l_gpio 3 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				reg = <0>;
+				panel0_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+		};
+	};
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&panel0_in>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&dsi_phy {
+	status = "okay";
+};
+
+&mdp {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
 &qspi {
 	status = "okay";
 	pinctrl-names = "default";
@@ -402,6 +454,19 @@ wifi-firmware {
 
 /* PINCTRL - additions to nodes defined in sc7180.dtsi */
 
+&pm6150l_gpio {
+	disp_pins: disp-pins {
+		pinconf {
+			pins = "gpio3";
+			function = PMIC_GPIO_FUNC_FUNC1;
+			qcom,drive-strength = <PMIC_GPIO_STRENGTH_MED>;
+			power-source = <0>;
+			bias-disable;
+			output-low;
+		};
+	};
+};
+
 &qspi_clk {
 	pinconf {
 		pins = "gpio63";
-- 
2.27.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel