[PATCH v3] drm/msm/dp: cleared DP_DOWNSPREAD_CTRL register before start link training

[PATCH v3] drm/msm/dp: cleared DP_DOWNSPREAD_CTRL register before start link training

[Kuogee Hsieh]

DOWNSPREAD_CTRL (0x107) shall be cleared to 0 upon power-on reset or an
upstream device disconnect. This patch will enforce this rule by always
cleared DOWNSPREAD_CTRL register to 0 before start link training. At rare
case that DP MSA timing parameters may be mis-interpreted by the sink
which causes audio sampling rate be calculated wrongly and cause audio
did not work at sink if DOWNSPREAD_CTRL register is not cleared to 0.
This patch also make sure bring sink out of D3 power-down mode into D0
(normal operation mode) successfully by retrying 3 times.

Changes in v2:
1) fix spelling at commit text
2) merge ssc variable into encoding[0]

Changes in v3:
-- correct spelling of DOWNSPREAD_CTRL
-- replace err with len of ssize_t

Fixes: 154b5a7da0fd ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
---
 drivers/gpu/drm/msm/dp/dp_ctrl.c | 13 +++++--------
 drivers/gpu/drm/msm/dp/dp_link.c | 21 ++++++++++++---------
 2 files changed, 17 insertions(+), 17 deletions(-)

diff --git a/drivers/gpu/drm/msm/dp/dp_ctrl.c b/drivers/gpu/drm/msm/dp/dp_ctrl.c
index ab6aa13..2c74c59 100644
--- a/drivers/gpu/drm/msm/dp/dp_ctrl.c
+++ b/drivers/gpu/drm/msm/dp/dp_ctrl.c
@@ -1245,8 +1245,7 @@ static int dp_ctrl_link_train(struct dp_ctrl_private *ctrl,
 {
 	int ret = 0;
 	const u8 *dpcd = ctrl->panel->dpcd;
-	u8 encoding = DP_SET_ANSI_8B10B;
-	u8 ssc;
+	u8 encoding[] = { 0, DP_SET_ANSI_8B10B };
 	u8 assr;
 	struct dp_link_info link_info = {0};
 
@@ -1258,13 +1257,11 @@ static int dp_ctrl_link_train(struct dp_ctrl_private *ctrl,
 
 	dp_aux_link_configure(ctrl->aux, &link_info);
 
-	if (drm_dp_max_downspread(dpcd)) {
-		ssc = DP_SPREAD_AMP_0_5;
-		drm_dp_dpcd_write(ctrl->aux, DP_DOWNSPREAD_CTRL, &ssc, 1);
-	}
+	if (drm_dp_max_downspread(dpcd))
+		encoding[0] |= DP_SPREAD_AMP_0_5;
 
-	drm_dp_dpcd_write(ctrl->aux, DP_MAIN_LINK_CHANNEL_CODING_SET,
-				&encoding, 1);
+	/* config DOWNSPREAD_CTRL and MAIN_LINK_CHANNEL_CODING_SET */
+	drm_dp_dpcd_write(ctrl->aux, DP_DOWNSPREAD_CTRL, encoding, 2);
 
 	if (drm_dp_alternate_scrambler_reset_cap(dpcd)) {
 		assr = DP_ALTERNATE_SCRAMBLER_RESET_ENABLE;
diff --git a/drivers/gpu/drm/msm/dp/dp_link.c b/drivers/gpu/drm/msm/dp/dp_link.c
index 36f0af0..7b5ecf5 100644
--- a/drivers/gpu/drm/msm/dp/dp_link.c
+++ b/drivers/gpu/drm/msm/dp/dp_link.c
@@ -49,23 +49,26 @@ static int dp_aux_link_power_up(struct drm_dp_aux *aux,
 					struct dp_link_info *link)
 {
 	u8 value;
-	int err;
+	ssize_t len;
+	int i;
 
 	if (link->revision < 0x11)
 		return 0;
 
-	err = drm_dp_dpcd_readb(aux, DP_SET_POWER, &value);
-	if (err < 0)
-		return err;
+	len = drm_dp_dpcd_readb(aux, DP_SET_POWER, &value);
+	if (len < 0)
+		return len;
 
 	value &= ~DP_SET_POWER_MASK;
 	value |= DP_SET_POWER_D0;
 
-	err = drm_dp_dpcd_writeb(aux, DP_SET_POWER, value);
-	if (err < 0)
-		return err;
-
-	usleep_range(1000, 2000);
+	/* retry for 1ms to give the sink time to wake up */
+	for (i = 0; i < 3; i++) {
+	        len = drm_dp_dpcd_writeb(aux, DP_SET_POWER, value);
+		usleep_range(1000, 2000);
+		if (len == 1)
+			break;
+	}
 
 	return 0;
 }
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH v3] drm/msm/dp: cleared DP_DOWNSPREAD_CTRL register before start link training

[Dmitry Baryshkov]

On Thu, 8 Sept 2022 at 18:38, Kuogee Hsieh <quic_khsieh@quicinc.com> wrote:
>
> DOWNSPREAD_CTRL (0x107) shall be cleared to 0 upon power-on reset or an
> upstream device disconnect. This patch will enforce this rule by always
> cleared DOWNSPREAD_CTRL register to 0 before start link training. At rare
> case that DP MSA timing parameters may be mis-interpreted by the sink
> which causes audio sampling rate be calculated wrongly and cause audio
> did not work at sink if DOWNSPREAD_CTRL register is not cleared to 0.
> This patch also make sure bring sink out of D3 power-down mode into D0
> (normal operation mode) successfully by retrying 3 times.

Split into three separate patches please.


-- 
With best wishes
Dmitry