From: Icenowy Zheng <icenowy@aosc.io>
To: Chen-Yu Tsai <wens@csie.org>,
Maxime Ripard <maxime.ripard@bootlin.com>,
Lee Jones <lee.jones@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org
Subject: Re: [PATCH 5/5] arm64: dts: allwinner: h6: enable AXP805 PMIC on Pine H64
Date: Tue, 26 Jun 2018 08:49:41 +0800 [thread overview]
Message-ID: <f93b1524657048279f54004fdbcd6ab5af9ec1c1.camel@aosc.io> (raw)
In-Reply-To: <20180620051540.25617-6-wens@csie.org>
在 2018-06-20三的 13:15 +0800，Chen-Yu Tsai写道：
> From: Icenowy Zheng <icenowy@aosc.io>
>
> Pine H64 board has an AXP805 PMIC on it.
>
> Enable it in the device tree.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
I suggest to mention the working mode change here.
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> ---
> .../boot/dts/allwinner/sun50i-h6-pine-h64.dts | 109
> ++++++++++++++++++
> 1 file changed, 109 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
> b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
> index 2e97173c9204..1673636358ef 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
> @@ -44,6 +44,115 @@
> &r_i2c {
> status = "okay";
>
> + axp805: pmic@36 {
> + compatible = "x-powers,axp805", "x-powers,axp806";
> + reg = <0x36>;
> + interrupt-parent = <&r_intc>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + x-powers,self-working-mode;
> +
> + regulators {
> + reg_aldo1: aldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-pl";
> + };
> +
> + reg_aldo2: aldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-ac200";
> + };
> +
> + reg_aldo3: aldo3 {
> + /* This regulator is connected with
> CLDO1 */
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-3v3-1";
> + };
> +
> + reg_bldo1: bldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-bias-pll";
> + };
> +
> + reg_bldo2: bldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-efuse-pcie-
> hdmi-io";
> + };
> +
> + reg_bldo3: bldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-dcxoio";
> + };
> +
> + bldo4 {
> + /* unused */
> + };
> +
> + reg_cldo1: cldo1 {
> + /* This regulator is connected with
> ALDO3 */
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-3v3-2";
> + };
> +
> + reg_cldo2: cldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi-1";
> + };
> +
> + reg_cldo3: cldo3 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi-2";
> + };
> +
> + reg_dcdca: dcdca {
> + regulator-always-on;
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-cpu";
> + };
> +
> + reg_dcdcc: dcdcc {
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-gpu";
> + };
> +
> + reg_dcdcd: dcdcd {
> + regulator-always-on;
> + regulator-min-microvolt = <960000>;
> + regulator-max-microvolt = <960000>;
> + regulator-name = "vdd-sys";
> + };
> +
> + reg_dcdce: dcdce {
> + regulator-always-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-name = "vcc-dram";
> + };
> +
> + sw {
> + /* unused */
> + };
> + };
> + };
> +
> pcf8563: rtc@51 {
> compatible = "nxp,pcf8563";
> reg = <0x51>;
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
WARNING: multiple messages have this Message-ID (diff)
From: icenowy@aosc.io (Icenowy Zheng)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 5/5] arm64: dts: allwinner: h6: enable AXP805 PMIC on Pine H64
Date: Tue, 26 Jun 2018 08:49:41 +0800 [thread overview]
Message-ID: <f93b1524657048279f54004fdbcd6ab5af9ec1c1.camel@aosc.io> (raw)
In-Reply-To: <20180620051540.25617-6-wens@csie.org>
? 2018-06-20?? 13:15 +0800?Chen-Yu Tsai???
> From: Icenowy Zheng <icenowy@aosc.io>
>
> Pine H64 board has an AXP805 PMIC on it.
>
> Enable it in the device tree.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
I suggest to mention the working mode change here.
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> ---
> .../boot/dts/allwinner/sun50i-h6-pine-h64.dts | 109
> ++++++++++++++++++
> 1 file changed, 109 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
> b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
> index 2e97173c9204..1673636358ef 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
> @@ -44,6 +44,115 @@
> &r_i2c {
> status = "okay";
>
> + axp805: pmic at 36 {
> + compatible = "x-powers,axp805", "x-powers,axp806";
> + reg = <0x36>;
> + interrupt-parent = <&r_intc>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + x-powers,self-working-mode;
> +
> + regulators {
> + reg_aldo1: aldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-pl";
> + };
> +
> + reg_aldo2: aldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-ac200";
> + };
> +
> + reg_aldo3: aldo3 {
> + /* This regulator is connected with
> CLDO1 */
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-3v3-1";
> + };
> +
> + reg_bldo1: bldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-bias-pll";
> + };
> +
> + reg_bldo2: bldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-efuse-pcie-
> hdmi-io";
> + };
> +
> + reg_bldo3: bldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-dcxoio";
> + };
> +
> + bldo4 {
> + /* unused */
> + };
> +
> + reg_cldo1: cldo1 {
> + /* This regulator is connected with
> ALDO3 */
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-3v3-2";
> + };
> +
> + reg_cldo2: cldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi-1";
> + };
> +
> + reg_cldo3: cldo3 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi-2";
> + };
> +
> + reg_dcdca: dcdca {
> + regulator-always-on;
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-cpu";
> + };
> +
> + reg_dcdcc: dcdcc {
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-gpu";
> + };
> +
> + reg_dcdcd: dcdcd {
> + regulator-always-on;
> + regulator-min-microvolt = <960000>;
> + regulator-max-microvolt = <960000>;
> + regulator-name = "vdd-sys";
> + };
> +
> + reg_dcdce: dcdce {
> + regulator-always-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-name = "vcc-dram";
> + };
> +
> + sw {
> + /* unused */
> + };
> + };
> + };
> +
> pcf8563: rtc at 51 {
> compatible = "nxp,pcf8563";
> reg = <0x51>;
next prev parent reply other threads:[~2018-06-26 0:49 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-06-20 5:15 [PATCH 0/5] arm64: allwinner: h6: Enable AXP805 PMIC on Pine H64 Chen-Yu Tsai
2018-06-20 5:15 ` Chen-Yu Tsai
2018-06-20 5:15 ` [PATCH 1/5] dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806 Chen-Yu Tsai
2018-06-20 5:15 ` Chen-Yu Tsai
2018-06-26 21:41 ` Rob Herring
2018-06-26 21:41 ` Rob Herring
2018-07-04 7:29 ` Lee Jones
2018-07-04 7:29 ` Lee Jones
2018-06-20 5:15 ` [PATCH 2/5] mfd: axp20x: Add self-working mode support " Chen-Yu Tsai
2018-06-20 5:15 ` Chen-Yu Tsai
2018-07-04 7:33 ` Lee Jones
2018-07-04 7:33 ` Lee Jones
2018-06-20 5:15 ` [PATCH 3/5] mfd: axp20x: Support AXP806 in I2C mode Chen-Yu Tsai
2018-06-20 5:15 ` Chen-Yu Tsai
2018-07-04 7:33 ` Lee Jones
2018-07-04 7:33 ` Lee Jones
2018-06-20 5:15 ` [PATCH 4/5] arm64: dts: allwinner: h6: Use macros for R_CCU clock and reset indices Chen-Yu Tsai
2018-06-20 5:15 ` Chen-Yu Tsai
2018-06-20 13:11 ` Icenowy Zheng
2018-06-20 13:11 ` Icenowy Zheng
2018-06-20 13:46 ` Chen-Yu Tsai
2018-06-20 13:46 ` Chen-Yu Tsai
2018-06-20 5:15 ` [PATCH 5/5] arm64: dts: allwinner: h6: enable AXP805 PMIC on Pine H64 Chen-Yu Tsai
2018-06-20 5:15 ` Chen-Yu Tsai
2018-06-26 0:49 ` Icenowy Zheng [this message]
2018-06-26 0:49 ` Icenowy Zheng
2018-06-26 3:46 ` Chen-Yu Tsai
2018-06-26 3:46 ` Chen-Yu Tsai
2018-06-26 5:14 ` [PATCH 0/5] arm64: allwinner: h6: Enable " Icenowy Zheng
2018-06-26 5:14 ` Icenowy Zheng
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=f93b1524657048279f54004fdbcd6ab5af9ec1c1.camel@aosc.io \
--to=icenowy@aosc.io \
--cc=andre.przywara@arm.com \
--cc=devicetree@vger.kernel.org \
--cc=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=mark.rutland@arm.com \
--cc=maxime.ripard@bootlin.com \
--cc=robh+dt@kernel.org \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.