* [Intel-gfx] [V8 1/9] drm/i915/dsi: Configure transcoder operation for command mode.
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
@ 2020-03-12 5:38 ` Vandita Kulkarni
2020-03-12 5:38 ` [Intel-gfx] [V8 2/9] drm/i915/dsi: Add vblank calculation " Vandita Kulkarni
` (15 subsequent siblings)
16 siblings, 0 replies; 20+ messages in thread
From: Vandita Kulkarni @ 2020-03-12 5:38 UTC (permalink / raw)
To: intel-gfx; +Cc: jani.nikula
Configure the transcoder to operate in TE GATE command mode
and take TE events from GPIO.
Also disable the periodic command mode, that GOP would have
programmed.
v2: Disable util pin (Jani)
v3: Use intel_de_write (Jani)
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
---
drivers/gpu/drm/i915/display/icl_dsi.c | 52 ++++++++++++++++++++++++++
1 file changed, 52 insertions(+)
diff --git a/drivers/gpu/drm/i915/display/icl_dsi.c b/drivers/gpu/drm/i915/display/icl_dsi.c
index 17cee6f80d8b..7744a6fd5d26 100644
--- a/drivers/gpu/drm/i915/display/icl_dsi.c
+++ b/drivers/gpu/drm/i915/display/icl_dsi.c
@@ -744,6 +744,18 @@ gen11_dsi_configure_transcoder(struct intel_encoder *encoder,
tmp |= VIDEO_MODE_SYNC_PULSE;
break;
}
+ } else {
+ /*
+ * FIXME: Retrieve this info from VBT.
+ * As per the spec when dsi transcoder is operating
+ * in TE GATE mode, TE comes from GPIO
+ * which is UTIL PIN for DSI 0.
+ * Also this GPIO would not be used for other
+ * purposes is an assumption.
+ */
+ tmp &= ~OP_MODE_MASK;
+ tmp |= CMD_MODE_TE_GATE;
+ tmp |= TE_SOURCE_GPIO;
}
intel_de_write(dev_priv, DSI_TRANS_FUNC_CONF(dsi_trans), tmp);
@@ -1016,6 +1028,32 @@ static void gen11_dsi_setup_timeouts(struct intel_encoder *encoder,
}
}
+static void gen11_dsi_config_util_pin(struct intel_encoder *encoder,
+ bool enable)
+{
+ struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+ struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder);
+ u32 tmp;
+
+ /*
+ * used as TE i/p for DSI0,
+ * for dual link/DSI1 TE is from slave DSI1
+ * through GPIO.
+ */
+ if (is_vid_mode(intel_dsi) || (intel_dsi->ports & BIT(PORT_B)))
+ return;
+
+ tmp = intel_de_read(dev_priv, UTIL_PIN_CTL);
+
+ if (enable) {
+ tmp |= UTIL_PIN_DIRECTION_INPUT;
+ tmp |= UTIL_PIN_ENABLE;
+ } else {
+ tmp &= ~UTIL_PIN_ENABLE;
+ }
+ intel_de_write(dev_priv, UTIL_PIN_CTL, tmp);
+}
+
static void
gen11_dsi_enable_port_and_phy(struct intel_encoder *encoder,
const struct intel_crtc_state *crtc_state)
@@ -1037,6 +1075,9 @@ gen11_dsi_enable_port_and_phy(struct intel_encoder *encoder,
/* setup D-PHY timings */
gen11_dsi_setup_dphy_timings(encoder, crtc_state);
+ /* Since transcoder is configured to take events from GPIO */
+ gen11_dsi_config_util_pin(encoder, true);
+
/* step 4h: setup DSI protocol timeouts */
gen11_dsi_setup_timeouts(encoder, crtc_state);
@@ -1180,6 +1221,15 @@ static void gen11_dsi_deconfigure_trancoder(struct intel_encoder *encoder)
enum transcoder dsi_trans;
u32 tmp;
+ /* disable periodic update mode */
+ if (is_cmd_mode(intel_dsi)) {
+ for_each_dsi_port(port, intel_dsi->ports) {
+ tmp = intel_de_read(dev_priv, DSI_CMD_FRMCTL(port));
+ tmp &= ~DSI_PERIODIC_FRAME_UPDATE_ENABLE;
+ intel_de_write(dev_priv, DSI_CMD_FRMCTL(port), tmp);
+ }
+ }
+
/* put dsi link in ULPS */
for_each_dsi_port(port, intel_dsi->ports) {
dsi_trans = dsi_port_to_transcoder(port);
@@ -1286,6 +1336,8 @@ static void gen11_dsi_disable(struct intel_encoder *encoder,
/* step3: disable port */
gen11_dsi_disable_port(encoder);
+ gen11_dsi_config_util_pin(encoder, false);
+
/* step4: disable IO power */
gen11_dsi_disable_io_power(encoder);
}
--
2.21.0.5.gaeb582a
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 20+ messages in thread* [Intel-gfx] [V8 2/9] drm/i915/dsi: Add vblank calculation for command mode
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
2020-03-12 5:38 ` [Intel-gfx] [V8 1/9] drm/i915/dsi: Configure transcoder operation for command mode Vandita Kulkarni
@ 2020-03-12 5:38 ` Vandita Kulkarni
2020-03-12 5:38 ` [Intel-gfx] [V8 3/9] drm/i915/dsi: Add cmd mode flags in display mode private flags Vandita Kulkarni
` (14 subsequent siblings)
16 siblings, 0 replies; 20+ messages in thread
From: Vandita Kulkarni @ 2020-03-12 5:38 UTC (permalink / raw)
To: intel-gfx; +Cc: jani.nikula
Transcoder timing calculation differ for command mode.
v2: Use is_vid_mode, and use same I915_WRITE (Jani)
v3: Adjust the calculations to reflect dsc compression ratio
v4: Rearrange the vertical and horizontal timing calc, optimize
local variables usage. (Jani)
v5: Fix the values used for calculation, use afe_clk for
byte clock calculation, use intel_de_write/read (Jani)
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
---
drivers/gpu/drm/i915/display/icl_dsi.c | 48 +++++++++++++++++++-------
1 file changed, 36 insertions(+), 12 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/icl_dsi.c b/drivers/gpu/drm/i915/display/icl_dsi.c
index 7744a6fd5d26..17aa3fd780a8 100644
--- a/drivers/gpu/drm/i915/display/icl_dsi.c
+++ b/drivers/gpu/drm/i915/display/icl_dsi.c
@@ -849,14 +849,33 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
}
hactive = adjusted_mode->crtc_hdisplay;
- htotal = DIV_ROUND_UP(adjusted_mode->crtc_htotal * mul, div);
+
+ if (is_vid_mode(intel_dsi))
+ htotal = DIV_ROUND_UP(adjusted_mode->crtc_htotal * mul, div);
+ else
+ htotal = DIV_ROUND_UP((hactive + 160) * mul, div);
+
hsync_start = DIV_ROUND_UP(adjusted_mode->crtc_hsync_start * mul, div);
hsync_end = DIV_ROUND_UP(adjusted_mode->crtc_hsync_end * mul, div);
hsync_size = hsync_end - hsync_start;
hback_porch = (adjusted_mode->crtc_htotal -
adjusted_mode->crtc_hsync_end);
vactive = adjusted_mode->crtc_vdisplay;
- vtotal = adjusted_mode->crtc_vtotal;
+
+ if (is_vid_mode(intel_dsi)) {
+ vtotal = adjusted_mode->crtc_vtotal;
+ } else {
+ int bpp, line_time_us, byte_clk_period_ns;
+
+ if (crtc_state->dsc.compression_enable)
+ bpp = crtc_state->dsc.compressed_bpp;
+ else
+ bpp = mipi_dsi_pixel_format_to_bpp(intel_dsi->pixel_format);
+
+ byte_clk_period_ns = 1000000 / afe_clk(encoder, crtc_state);
+ line_time_us = (htotal * (bpp / 8) * byte_clk_period_ns) / (1000 * intel_dsi->lane_count);
+ vtotal = vactive + DIV_ROUND_UP(400, line_time_us);
+ }
vsync_start = adjusted_mode->crtc_vsync_start;
vsync_end = adjusted_mode->crtc_vsync_end;
vsync_shift = hsync_start - htotal / 2;
@@ -885,7 +904,7 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
}
/* TRANS_HSYNC register to be programmed only for video mode */
- if (intel_dsi->operation_mode == INTEL_DSI_VIDEO_MODE) {
+ if (is_vid_mode(intel_dsi)) {
if (intel_dsi->video_mode_format ==
VIDEO_MODE_NON_BURST_WITH_SYNC_PULSE) {
/* BSPEC: hsync size should be atleast 16 pixels */
@@ -928,22 +947,27 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
if (vsync_start < vactive)
drm_err(&dev_priv->drm, "vsync_start less than vactive\n");
- /* program TRANS_VSYNC register */
- for_each_dsi_port(port, intel_dsi->ports) {
- dsi_trans = dsi_port_to_transcoder(port);
- intel_de_write(dev_priv, VSYNC(dsi_trans),
- (vsync_start - 1) | ((vsync_end - 1) << 16));
+ /* program TRANS_VSYNC register for video mode only */
+ if (is_vid_mode(intel_dsi)) {
+ for_each_dsi_port(port, intel_dsi->ports) {
+ dsi_trans = dsi_port_to_transcoder(port);
+ intel_de_write(dev_priv, VSYNC(dsi_trans),
+ (vsync_start - 1) | ((vsync_end - 1) << 16));
+ }
}
/*
- * FIXME: It has to be programmed only for interlaced
+ * FIXME: It has to be programmed only for video modes and interlaced
* modes. Put the check condition here once interlaced
* info available as described above.
* program TRANS_VSYNCSHIFT register
*/
- for_each_dsi_port(port, intel_dsi->ports) {
- dsi_trans = dsi_port_to_transcoder(port);
- intel_de_write(dev_priv, VSYNCSHIFT(dsi_trans), vsync_shift);
+ if (is_vid_mode(intel_dsi)) {
+ for_each_dsi_port(port, intel_dsi->ports) {
+ dsi_trans = dsi_port_to_transcoder(port);
+ intel_de_write(dev_priv, VSYNCSHIFT(dsi_trans),
+ vsync_shift);
+ }
}
/* program TRANS_VBLANK register, should be same as vtotal programmed */
--
2.21.0.5.gaeb582a
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 20+ messages in thread* [Intel-gfx] [V8 3/9] drm/i915/dsi: Add cmd mode flags in display mode private flags
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
2020-03-12 5:38 ` [Intel-gfx] [V8 1/9] drm/i915/dsi: Configure transcoder operation for command mode Vandita Kulkarni
2020-03-12 5:38 ` [Intel-gfx] [V8 2/9] drm/i915/dsi: Add vblank calculation " Vandita Kulkarni
@ 2020-03-12 5:38 ` Vandita Kulkarni
2020-03-12 5:38 ` [Intel-gfx] [V8 4/9] drm/i915/dsi: Add check for periodic command mode Vandita Kulkarni
` (13 subsequent siblings)
16 siblings, 0 replies; 20+ messages in thread
From: Vandita Kulkarni @ 2020-03-12 5:38 UTC (permalink / raw)
To: intel-gfx; +Cc: jani.nikula
Adding TE flags and periodic command mode flags
as part of private flags to indicate what TE interrupts
we would be getting instead of vblanks in case of mipi dsi
command mode.
v2: Add TE flag description (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
---
drivers/gpu/drm/i915/display/intel_display_types.h | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h b/drivers/gpu/drm/i915/display/intel_display_types.h
index 5e00e611f077..b94088642aff 100644
--- a/drivers/gpu/drm/i915/display/intel_display_types.h
+++ b/drivers/gpu/drm/i915/display/intel_display_types.h
@@ -640,6 +640,16 @@ struct intel_crtc_scaler_state {
#define I915_MODE_FLAG_GET_SCANLINE_FROM_TIMESTAMP (1<<1)
/* Flag to use the scanline counter instead of the pixel counter */
#define I915_MODE_FLAG_USE_SCANLINE_COUNTER (1<<2)
+/*
+ * TE0 or TE1 flag is set if the crtc has a DSI encoder which
+ * is operating in command mode.
+ * Flag to use TE from DSI0 instead of VBI in command mode
+ */
+#define I915_MODE_FLAG_DSI_USE_TE0 (1<<3)
+/* Flag to use TE from DSI1 instead of VBI in command mode */
+#define I915_MODE_FLAG_DSI_USE_TE1 (1<<4)
+/* Flag to indicate mipi dsi periodic command mode where we do not get TE */
+#define I915_MODE_FLAG_DSI_PERIODIC_CMD_MODE (1<<5)
struct intel_wm_level {
bool enable;
--
2.21.0.5.gaeb582a
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 20+ messages in thread* [Intel-gfx] [V8 4/9] drm/i915/dsi: Add check for periodic command mode
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
` (2 preceding siblings ...)
2020-03-12 5:38 ` [Intel-gfx] [V8 3/9] drm/i915/dsi: Add cmd mode flags in display mode private flags Vandita Kulkarni
@ 2020-03-12 5:38 ` Vandita Kulkarni
2020-03-12 5:38 ` [Intel-gfx] [V8 5/9] drm/i915/dsi: Use private flags to indicate TE in cmd mode Vandita Kulkarni
` (12 subsequent siblings)
16 siblings, 0 replies; 20+ messages in thread
From: Vandita Kulkarni @ 2020-03-12 5:38 UTC (permalink / raw)
To: intel-gfx; +Cc: jani.nikula
If the GOP has programmed periodic command mode,
we need to disable that which would need a
deconfigure and configure sequence.
v2: Fix sparse error, pass only intel_dsi (Jani)
v3: Use intel_de_read
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
---
drivers/gpu/drm/i915/display/icl_dsi.c | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/drivers/gpu/drm/i915/display/icl_dsi.c b/drivers/gpu/drm/i915/display/icl_dsi.c
index 17aa3fd780a8..949f4867402b 100644
--- a/drivers/gpu/drm/i915/display/icl_dsi.c
+++ b/drivers/gpu/drm/i915/display/icl_dsi.c
@@ -1423,6 +1423,22 @@ static void gen11_dsi_get_timings(struct intel_encoder *encoder,
adjusted_mode->crtc_vblank_end = adjusted_mode->crtc_vtotal;
}
+static bool gen11_dsi_is_periodic_cmd_mode(struct intel_dsi *intel_dsi)
+{
+ struct drm_device *dev = intel_dsi->base.base.dev;
+ struct drm_i915_private *dev_priv = to_i915(dev);
+ enum transcoder dsi_trans;
+ u32 val;
+
+ if (intel_dsi->ports == BIT(PORT_B))
+ dsi_trans = TRANSCODER_DSI_1;
+ else
+ dsi_trans = TRANSCODER_DSI_0;
+
+ val = intel_de_read(dev_priv, DSI_TRANS_FUNC_CONF(dsi_trans));
+ return (val & DSI_PERIODIC_FRAME_UPDATE_ENABLE);
+}
+
static void gen11_dsi_get_config(struct intel_encoder *encoder,
struct intel_crtc_state *pipe_config)
{
@@ -1443,6 +1459,10 @@ static void gen11_dsi_get_config(struct intel_encoder *encoder,
gen11_dsi_get_timings(encoder, pipe_config);
pipe_config->output_types |= BIT(INTEL_OUTPUT_DSI);
pipe_config->pipe_bpp = bdw_get_pipemisc_bpp(crtc);
+
+ if (gen11_dsi_is_periodic_cmd_mode(intel_dsi))
+ pipe_config->hw.adjusted_mode.private_flags |=
+ I915_MODE_FLAG_DSI_PERIODIC_CMD_MODE;
}
static int gen11_dsi_dsc_compute_config(struct intel_encoder *encoder,
@@ -1526,6 +1546,10 @@ static int gen11_dsi_compute_config(struct intel_encoder *encoder,
pipe_config->port_clock = afe_clk(encoder, pipe_config) / 5;
+ /* We would not operate in periodic command mode */
+ pipe_config->hw.adjusted_mode.private_flags &=
+ ~I915_MODE_FLAG_DSI_PERIODIC_CMD_MODE;
+
return 0;
}
--
2.21.0.5.gaeb582a
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 20+ messages in thread* [Intel-gfx] [V8 5/9] drm/i915/dsi: Use private flags to indicate TE in cmd mode
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
` (3 preceding siblings ...)
2020-03-12 5:38 ` [Intel-gfx] [V8 4/9] drm/i915/dsi: Add check for periodic command mode Vandita Kulkarni
@ 2020-03-12 5:38 ` Vandita Kulkarni
2020-03-24 15:28 ` Jani Nikula
2020-03-12 5:38 ` [Intel-gfx] [V8 6/9] drm/i915/dsi: Configure TE interrupt for " Vandita Kulkarni
` (11 subsequent siblings)
16 siblings, 1 reply; 20+ messages in thread
From: Vandita Kulkarni @ 2020-03-12 5:38 UTC (permalink / raw)
To: intel-gfx; +Cc: jani.nikula
On dsi cmd mode we do not receive vblanks instead
we would get TE and these flags indicate TE is expected on
which port.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
---
drivers/gpu/drm/i915/display/icl_dsi.c | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/drivers/gpu/drm/i915/display/icl_dsi.c b/drivers/gpu/drm/i915/display/icl_dsi.c
index 949f4867402b..d452037b1ac9 100644
--- a/drivers/gpu/drm/i915/display/icl_dsi.c
+++ b/drivers/gpu/drm/i915/display/icl_dsi.c
@@ -1550,6 +1550,24 @@ static int gen11_dsi_compute_config(struct intel_encoder *encoder,
pipe_config->hw.adjusted_mode.private_flags &=
~I915_MODE_FLAG_DSI_PERIODIC_CMD_MODE;
+ /*
+ * In case of TE GATE cmd mode, we
+ * receive TE from the slave if
+ * dual link is enabled
+ */
+ if (is_cmd_mode(intel_dsi)) {
+ if (intel_dsi->ports == (BIT(PORT_B) | BIT(PORT_A)))
+ pipe_config->hw.adjusted_mode.private_flags |=
+ I915_MODE_FLAG_DSI_USE_TE1 |
+ I915_MODE_FLAG_DSI_USE_TE0;
+ else if (intel_dsi->ports == BIT(PORT_B))
+ pipe_config->hw.adjusted_mode.private_flags |=
+ I915_MODE_FLAG_DSI_USE_TE1;
+ else
+ pipe_config->hw.adjusted_mode.private_flags |=
+ I915_MODE_FLAG_DSI_USE_TE0;
+ }
+
return 0;
}
--
2.21.0.5.gaeb582a
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 20+ messages in thread* Re: [Intel-gfx] [V8 5/9] drm/i915/dsi: Use private flags to indicate TE in cmd mode
2020-03-12 5:38 ` [Intel-gfx] [V8 5/9] drm/i915/dsi: Use private flags to indicate TE in cmd mode Vandita Kulkarni
@ 2020-03-24 15:28 ` Jani Nikula
0 siblings, 0 replies; 20+ messages in thread
From: Jani Nikula @ 2020-03-24 15:28 UTC (permalink / raw)
To: Vandita Kulkarni, intel-gfx
On Thu, 12 Mar 2020, Vandita Kulkarni <vandita.kulkarni@intel.com> wrote:
> On dsi cmd mode we do not receive vblanks instead
> we would get TE and these flags indicate TE is expected on
> which port.
>
> Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
> Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Pushed up to and including this patch.
BR,
Jani.
> ---
> drivers/gpu/drm/i915/display/icl_dsi.c | 18 ++++++++++++++++++
> 1 file changed, 18 insertions(+)
>
> diff --git a/drivers/gpu/drm/i915/display/icl_dsi.c b/drivers/gpu/drm/i915/display/icl_dsi.c
> index 949f4867402b..d452037b1ac9 100644
> --- a/drivers/gpu/drm/i915/display/icl_dsi.c
> +++ b/drivers/gpu/drm/i915/display/icl_dsi.c
> @@ -1550,6 +1550,24 @@ static int gen11_dsi_compute_config(struct intel_encoder *encoder,
> pipe_config->hw.adjusted_mode.private_flags &=
> ~I915_MODE_FLAG_DSI_PERIODIC_CMD_MODE;
>
> + /*
> + * In case of TE GATE cmd mode, we
> + * receive TE from the slave if
> + * dual link is enabled
> + */
> + if (is_cmd_mode(intel_dsi)) {
> + if (intel_dsi->ports == (BIT(PORT_B) | BIT(PORT_A)))
> + pipe_config->hw.adjusted_mode.private_flags |=
> + I915_MODE_FLAG_DSI_USE_TE1 |
> + I915_MODE_FLAG_DSI_USE_TE0;
> + else if (intel_dsi->ports == BIT(PORT_B))
> + pipe_config->hw.adjusted_mode.private_flags |=
> + I915_MODE_FLAG_DSI_USE_TE1;
> + else
> + pipe_config->hw.adjusted_mode.private_flags |=
> + I915_MODE_FLAG_DSI_USE_TE0;
> + }
> +
> return 0;
> }
--
Jani Nikula, Intel Open Source Graphics Center
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 20+ messages in thread
* [Intel-gfx] [V8 6/9] drm/i915/dsi: Configure TE interrupt for cmd mode
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
` (4 preceding siblings ...)
2020-03-12 5:38 ` [Intel-gfx] [V8 5/9] drm/i915/dsi: Use private flags to indicate TE in cmd mode Vandita Kulkarni
@ 2020-03-12 5:38 ` Vandita Kulkarni
2020-03-12 5:38 ` [Intel-gfx] [V8 7/9] drm/i915/dsi: Add TE handler for dsi " Vandita Kulkarni
` (10 subsequent siblings)
16 siblings, 0 replies; 20+ messages in thread
From: Vandita Kulkarni @ 2020-03-12 5:38 UTC (permalink / raw)
To: intel-gfx; +Cc: jani.nikula
We need to configure TE interrupt in two places.
Port interrupt and DSI interrupt mask registers.
v2: Hide the private flags check inside configure_te (Jani)
v3: Fix the position of masking de_port_masked for DSI_TE.
v4: Simplify the caller of configure_te (Jani)
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
---
drivers/gpu/drm/i915/i915_irq.c | 49 +++++++++++++++++++++++++++++++--
1 file changed, 47 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
index 9f0653cf0510..89489a247276 100644
--- a/drivers/gpu/drm/i915/i915_irq.c
+++ b/drivers/gpu/drm/i915/i915_irq.c
@@ -40,6 +40,7 @@
#include "display/intel_hotplug.h"
#include "display/intel_lpe_audio.h"
#include "display/intel_psr.h"
+#include "display/intel_dsi.h"
#include "gt/intel_gt.h"
#include "gt/intel_gt_irq.h"
@@ -2617,12 +2618,45 @@ int ilk_enable_vblank(struct drm_crtc *crtc)
return 0;
}
+static bool gen11_dsi_configure_te(struct intel_crtc *intel_crtc,
+ bool enable)
+{
+ struct drm_i915_private *dev_priv = to_i915(intel_crtc->base.dev);
+ struct intel_crtc_state *config = intel_crtc->config;
+ struct drm_display_mode *mode = &config->hw.adjusted_mode;
+ enum port port;
+ u32 tmp;
+
+ if (!(mode->private_flags &
+ (I915_MODE_FLAG_DSI_USE_TE1 | I915_MODE_FLAG_DSI_USE_TE0)))
+ return false;
+
+ /* for dual link cases we consider TE from slave */
+ if (mode->private_flags & I915_MODE_FLAG_DSI_USE_TE1)
+ port = PORT_B;
+ else
+ port = PORT_A;
+
+ tmp = I915_READ(DSI_INTR_MASK_REG(port));
+ if (enable)
+ tmp &= ~DSI_TE_EVENT;
+ else
+ tmp |= DSI_TE_EVENT;
+
+ I915_WRITE(DSI_INTR_MASK_REG(port), tmp);
+ return true;
+}
+
int bdw_enable_vblank(struct drm_crtc *crtc)
{
struct drm_i915_private *dev_priv = to_i915(crtc->dev);
- enum pipe pipe = to_intel_crtc(crtc)->pipe;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ enum pipe pipe = intel_crtc->pipe;
unsigned long irqflags;
+ if (gen11_dsi_configure_te(intel_crtc, true))
+ return 0;
+
spin_lock_irqsave(&dev_priv->irq_lock, irqflags);
bdw_enable_pipe_irq(dev_priv, pipe, GEN8_PIPE_VBLANK);
spin_unlock_irqrestore(&dev_priv->irq_lock, irqflags);
@@ -2688,9 +2722,13 @@ void ilk_disable_vblank(struct drm_crtc *crtc)
void bdw_disable_vblank(struct drm_crtc *crtc)
{
struct drm_i915_private *dev_priv = to_i915(crtc->dev);
- enum pipe pipe = to_intel_crtc(crtc)->pipe;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ enum pipe pipe = intel_crtc->pipe;
unsigned long irqflags;
+ if (gen11_dsi_configure_te(intel_crtc, false))
+ return;
+
spin_lock_irqsave(&dev_priv->irq_lock, irqflags);
bdw_disable_pipe_irq(dev_priv, pipe, GEN8_PIPE_VBLANK);
spin_unlock_irqrestore(&dev_priv->irq_lock, irqflags);
@@ -3384,6 +3422,13 @@ static void gen8_de_irq_postinstall(struct drm_i915_private *dev_priv)
if (IS_CNL_WITH_PORT_F(dev_priv) || INTEL_GEN(dev_priv) >= 11)
de_port_masked |= CNL_AUX_CHANNEL_F;
+ if (INTEL_GEN(dev_priv) >= 11) {
+ enum port port;
+
+ if (intel_bios_is_dsi_present(dev_priv, &port))
+ de_port_masked |= DSI0_TE | DSI1_TE;
+ }
+
de_pipe_enables = de_pipe_masked | GEN8_PIPE_VBLANK |
GEN8_PIPE_FIFO_UNDERRUN;
--
2.21.0.5.gaeb582a
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 20+ messages in thread* [Intel-gfx] [V8 7/9] drm/i915/dsi: Add TE handler for dsi cmd mode.
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
` (5 preceding siblings ...)
2020-03-12 5:38 ` [Intel-gfx] [V8 6/9] drm/i915/dsi: Configure TE interrupt for " Vandita Kulkarni
@ 2020-03-12 5:38 ` Vandita Kulkarni
2020-03-24 15:31 ` Jani Nikula
2020-03-12 5:38 ` [Intel-gfx] [V8 8/9] drm/i915/dsi: Initiate fame request in " Vandita Kulkarni
` (9 subsequent siblings)
16 siblings, 1 reply; 20+ messages in thread
From: Vandita Kulkarni @ 2020-03-12 5:38 UTC (permalink / raw)
To: intel-gfx; +Cc: jani.nikula
In case of dual link, we get the TE on slave.
So clear the TE on slave DSI IIR.
v2: Pass only relevant masked bits to the handler (Jani)
v3: Fix the check for cmd mode in TE handler function.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
---
drivers/gpu/drm/i915/i915_irq.c | 64 +++++++++++++++++++++++++++++++++
1 file changed, 64 insertions(+)
diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
index 89489a247276..2e1418515c9f 100644
--- a/drivers/gpu/drm/i915/i915_irq.c
+++ b/drivers/gpu/drm/i915/i915_irq.c
@@ -2262,6 +2262,62 @@ gen8_de_misc_irq_handler(struct drm_i915_private *dev_priv, u32 iir)
drm_err(&dev_priv->drm, "Unexpected DE Misc interrupt\n");
}
+void gen11_dsi_te_interrupt_handler(struct drm_i915_private *dev_priv,
+ u32 te_trigger)
+{
+ enum pipe pipe = INVALID_PIPE;
+ enum transcoder dsi_trans;
+ enum port port;
+ u32 val, tmp;
+
+ /*
+ * Incase of dual link, TE comes from DSI_1
+ * this is to check if dual link is enabled
+ */
+ val = I915_READ(TRANS_DDI_FUNC_CTL2(TRANSCODER_DSI_0));
+ val &= PORT_SYNC_MODE_ENABLE;
+
+ /*
+ * if dual link is enabled, then read DSI_0
+ * transcoder registers
+ */
+ port = ((te_trigger & DSI1_TE && val) || (te_trigger & DSI0_TE)) ?
+ PORT_A : PORT_B;
+ dsi_trans = (port == PORT_A) ? TRANSCODER_DSI_0 : TRANSCODER_DSI_1;
+
+ /* Check if DSI configured in command mode */
+ val = I915_READ(DSI_TRANS_FUNC_CONF(dsi_trans));
+ val = val & OP_MODE_MASK;
+
+ if ((val != CMD_MODE_NO_GATE) && (val != CMD_MODE_TE_GATE)) {
+ DRM_ERROR("DSI trancoder not configured in command mode\n");
+ return;
+ }
+
+ /* Get PIPE for handling VBLANK event */
+ val = I915_READ(TRANS_DDI_FUNC_CTL(dsi_trans));
+ switch (val & TRANS_DDI_EDP_INPUT_MASK) {
+ case TRANS_DDI_EDP_INPUT_A_ON:
+ pipe = PIPE_A;
+ break;
+ case TRANS_DDI_EDP_INPUT_B_ONOFF:
+ pipe = PIPE_B;
+ break;
+ case TRANS_DDI_EDP_INPUT_C_ONOFF:
+ pipe = PIPE_C;
+ break;
+ default:
+ DRM_ERROR("Invalid PIPE\n");
+ }
+
+ /* clear TE in dsi IIR */
+ port = (te_trigger & DSI1_TE) ? PORT_B : PORT_A;
+ tmp = I915_READ(DSI_INTR_IDENT_REG(port));
+ I915_WRITE(DSI_INTR_IDENT_REG(port), tmp);
+
+ drm_handle_vblank(&dev_priv->drm, pipe);
+}
+
static irqreturn_t
gen8_de_irq_handler(struct drm_i915_private *dev_priv, u32 master_ctl)
{
@@ -2328,6 +2384,14 @@ gen8_de_irq_handler(struct drm_i915_private *dev_priv, u32 master_ctl)
found = true;
}
+ if (INTEL_GEN(dev_priv) >= 11) {
+ tmp_mask = iir & (DSI0_TE | DSI1_TE);
+ if (tmp_mask) {
+ gen11_dsi_te_interrupt_handler(dev_priv, tmp_mask);
+ found = true;
+ }
+ }
+
if (!found)
drm_err(&dev_priv->drm,
"Unexpected DE Port interrupt\n");
--
2.21.0.5.gaeb582a
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 20+ messages in thread* Re: [Intel-gfx] [V8 7/9] drm/i915/dsi: Add TE handler for dsi cmd mode.
2020-03-12 5:38 ` [Intel-gfx] [V8 7/9] drm/i915/dsi: Add TE handler for dsi " Vandita Kulkarni
@ 2020-03-24 15:31 ` Jani Nikula
0 siblings, 0 replies; 20+ messages in thread
From: Jani Nikula @ 2020-03-24 15:31 UTC (permalink / raw)
To: Vandita Kulkarni, intel-gfx
On Thu, 12 Mar 2020, Vandita Kulkarni <vandita.kulkarni@intel.com> wrote:
> In case of dual link, we get the TE on slave.
> So clear the TE on slave DSI IIR.
>
> v2: Pass only relevant masked bits to the handler (Jani)
>
> v3: Fix the check for cmd mode in TE handler function.
>
> Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
> ---
> drivers/gpu/drm/i915/i915_irq.c | 64 +++++++++++++++++++++++++++++++++
> 1 file changed, 64 insertions(+)
>
> diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
> index 89489a247276..2e1418515c9f 100644
> --- a/drivers/gpu/drm/i915/i915_irq.c
> +++ b/drivers/gpu/drm/i915/i915_irq.c
> @@ -2262,6 +2262,62 @@ gen8_de_misc_irq_handler(struct drm_i915_private *dev_priv, u32 iir)
> drm_err(&dev_priv->drm, "Unexpected DE Misc interrupt\n");
> }
>
> +void gen11_dsi_te_interrupt_handler(struct drm_i915_private *dev_priv,
> + u32 te_trigger)
> +{
> + enum pipe pipe = INVALID_PIPE;
> + enum transcoder dsi_trans;
> + enum port port;
> + u32 val, tmp;
> +
> + /*
> + * Incase of dual link, TE comes from DSI_1
> + * this is to check if dual link is enabled
> + */
> + val = I915_READ(TRANS_DDI_FUNC_CTL2(TRANSCODER_DSI_0));
> + val &= PORT_SYNC_MODE_ENABLE;
> +
> + /*
> + * if dual link is enabled, then read DSI_0
> + * transcoder registers
> + */
> + port = ((te_trigger & DSI1_TE && val) || (te_trigger & DSI0_TE)) ?
> + PORT_A : PORT_B;
> + dsi_trans = (port == PORT_A) ? TRANSCODER_DSI_0 : TRANSCODER_DSI_1;
> +
> + /* Check if DSI configured in command mode */
> + val = I915_READ(DSI_TRANS_FUNC_CONF(dsi_trans));
> + val = val & OP_MODE_MASK;
> +
> + if ((val != CMD_MODE_NO_GATE) && (val != CMD_MODE_TE_GATE)) {
> + DRM_ERROR("DSI trancoder not configured in command mode\n");
drm_err()
> + return;
> + }
> +
> + /* Get PIPE for handling VBLANK event */
> + val = I915_READ(TRANS_DDI_FUNC_CTL(dsi_trans));
> + switch (val & TRANS_DDI_EDP_INPUT_MASK) {
> + case TRANS_DDI_EDP_INPUT_A_ON:
> + pipe = PIPE_A;
> + break;
> + case TRANS_DDI_EDP_INPUT_B_ONOFF:
> + pipe = PIPE_B;
> + break;
> + case TRANS_DDI_EDP_INPUT_C_ONOFF:
> + pipe = PIPE_C;
> + break;
> + default:
> + DRM_ERROR("Invalid PIPE\n");
drm_err()... but don't want to pass INVALID_PIPE to
intel_handle_vblank() below.
> + }
> +
> + /* clear TE in dsi IIR */
> + port = (te_trigger & DSI1_TE) ? PORT_B : PORT_A;
> + tmp = I915_READ(DSI_INTR_IDENT_REG(port));
> + I915_WRITE(DSI_INTR_IDENT_REG(port), tmp);
> +
> + drm_handle_vblank(&dev_priv->drm, pipe);
Please use intel_handle_vblank(). It takes into account pipe might not
match crtc index.
> +}
> +
> static irqreturn_t
> gen8_de_irq_handler(struct drm_i915_private *dev_priv, u32 master_ctl)
> {
> @@ -2328,6 +2384,14 @@ gen8_de_irq_handler(struct drm_i915_private *dev_priv, u32 master_ctl)
> found = true;
> }
>
> + if (INTEL_GEN(dev_priv) >= 11) {
> + tmp_mask = iir & (DSI0_TE | DSI1_TE);
> + if (tmp_mask) {
> + gen11_dsi_te_interrupt_handler(dev_priv, tmp_mask);
> + found = true;
> + }
> + }
> +
> if (!found)
> drm_err(&dev_priv->drm,
> "Unexpected DE Port interrupt\n");
--
Jani Nikula, Intel Open Source Graphics Center
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 20+ messages in thread
* [Intel-gfx] [V8 8/9] drm/i915/dsi: Initiate fame request in cmd mode
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
` (6 preceding siblings ...)
2020-03-12 5:38 ` [Intel-gfx] [V8 7/9] drm/i915/dsi: Add TE handler for dsi " Vandita Kulkarni
@ 2020-03-12 5:38 ` Vandita Kulkarni
2020-03-12 5:38 ` [Intel-gfx] [V8 9/9] drm/i915/dsi: Clear the DSI IIR Vandita Kulkarni
` (8 subsequent siblings)
16 siblings, 0 replies; 20+ messages in thread
From: Vandita Kulkarni @ 2020-03-12 5:38 UTC (permalink / raw)
To: intel-gfx; +Cc: jani.nikula
In TE Gate mode, on every flip we need to set the
frame update request bit. After this bit is set
transcoder hardware will automatically send the
frame data to the panel when it receives the TE event.
v2: Use intel_de_read/write
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
---
drivers/gpu/drm/i915/display/icl_dsi.c | 26 ++++++++++++++++++++
drivers/gpu/drm/i915/display/intel_display.c | 12 +++++++++
drivers/gpu/drm/i915/display/intel_dsi.h | 3 +++
3 files changed, 41 insertions(+)
diff --git a/drivers/gpu/drm/i915/display/icl_dsi.c b/drivers/gpu/drm/i915/display/icl_dsi.c
index d452037b1ac9..0e655be9b9cf 100644
--- a/drivers/gpu/drm/i915/display/icl_dsi.c
+++ b/drivers/gpu/drm/i915/display/icl_dsi.c
@@ -202,6 +202,32 @@ static int dsi_send_pkt_payld(struct intel_dsi_host *host,
return 0;
}
+void gen11_dsi_frame_update(struct intel_crtc_state *crtc_state)
+{
+ struct intel_crtc *crtc = to_intel_crtc(crtc_state->uapi.crtc);
+ struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
+ u32 tmp, private_flags;
+ enum port port;
+
+ private_flags = crtc_state->hw.adjusted_mode.private_flags;
+
+ /*
+ * case 1 also covers dual link
+ * In case of dual link, frame update should be set on
+ * DSI_0
+ */
+ if (private_flags & I915_MODE_FLAG_DSI_USE_TE0)
+ port = PORT_A;
+ else if (private_flags & I915_MODE_FLAG_DSI_USE_TE1)
+ port = PORT_B;
+ else
+ return;
+
+ tmp = intel_de_read(dev_priv, DSI_CMD_FRMCTL(port));
+ tmp |= DSI_FRAME_UPDATE_REQUEST;
+ intel_de_write(dev_priv, DSI_CMD_FRMCTL(port), tmp);
+}
+
static void dsi_program_swing_and_deemphasis(struct intel_encoder *encoder)
{
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
diff --git a/drivers/gpu/drm/i915/display/intel_display.c b/drivers/gpu/drm/i915/display/intel_display.c
index 8f23c4d51c33..9f99eea8e4ba 100644
--- a/drivers/gpu/drm/i915/display/intel_display.c
+++ b/drivers/gpu/drm/i915/display/intel_display.c
@@ -15601,6 +15601,18 @@ static void intel_atomic_commit_tail(struct intel_atomic_state *state)
intel_color_load_luts(new_crtc_state);
}
+ /*
+ * Incase of mipi dsi command mode, we need to set frame update
+ * for every commit
+ */
+ for_each_new_intel_crtc_in_state(state, crtc, new_crtc_state, i) {
+ if ((INTEL_GEN(dev_priv) >= 11) &&
+ (intel_crtc_has_type(new_crtc_state, INTEL_OUTPUT_DSI))) {
+ if (new_crtc_state->hw.active)
+ gen11_dsi_frame_update(new_crtc_state);
+ }
+ }
+
/*
* Now that the vblank has passed, we can go ahead and program the
* optimal watermarks on platforms that need two-step watermark
diff --git a/drivers/gpu/drm/i915/display/intel_dsi.h b/drivers/gpu/drm/i915/display/intel_dsi.h
index 19f78a4022d3..08f1f586eefb 100644
--- a/drivers/gpu/drm/i915/display/intel_dsi.h
+++ b/drivers/gpu/drm/i915/display/intel_dsi.h
@@ -205,6 +205,9 @@ u32 bxt_dsi_get_pclk(struct intel_encoder *encoder,
struct intel_crtc_state *config);
void bxt_dsi_reset_clocks(struct intel_encoder *encoder, enum port port);
+/* icl_dsi.c */
+void gen11_dsi_frame_update(struct intel_crtc_state *crtc_state);
+
/* intel_dsi_vbt.c */
bool intel_dsi_vbt_init(struct intel_dsi *intel_dsi, u16 panel_id);
void intel_dsi_vbt_gpio_init(struct intel_dsi *intel_dsi, bool panel_is_on);
--
2.21.0.5.gaeb582a
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 20+ messages in thread* [Intel-gfx] [V8 9/9] drm/i915/dsi: Clear the DSI IIR
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
` (7 preceding siblings ...)
2020-03-12 5:38 ` [Intel-gfx] [V8 8/9] drm/i915/dsi: Initiate fame request in " Vandita Kulkarni
@ 2020-03-12 5:38 ` Vandita Kulkarni
2020-03-12 6:37 ` [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for mipi dsi cmd mode (rev7) Patchwork
` (7 subsequent siblings)
16 siblings, 0 replies; 20+ messages in thread
From: Vandita Kulkarni @ 2020-03-12 5:38 UTC (permalink / raw)
To: intel-gfx; +Cc: jani.nikula
Clear the DSI IIR as part of interrupt configuration.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
---
drivers/gpu/drm/i915/i915_irq.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
index 2e1418515c9f..89c8cabe24e0 100644
--- a/drivers/gpu/drm/i915/i915_irq.c
+++ b/drivers/gpu/drm/i915/i915_irq.c
@@ -2708,6 +2708,11 @@ static bool gen11_dsi_configure_te(struct intel_crtc *intel_crtc,
tmp |= DSI_TE_EVENT;
I915_WRITE(DSI_INTR_MASK_REG(port), tmp);
+
+ /* FIXME: right place to clear this */
+ tmp = I915_READ(DSI_INTR_IDENT_REG(port));
+ I915_WRITE(DSI_INTR_IDENT_REG(port), tmp);
+
return true;
}
--
2.21.0.5.gaeb582a
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 20+ messages in thread* [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for mipi dsi cmd mode (rev7)
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
` (8 preceding siblings ...)
2020-03-12 5:38 ` [Intel-gfx] [V8 9/9] drm/i915/dsi: Clear the DSI IIR Vandita Kulkarni
@ 2020-03-12 6:37 ` Patchwork
2020-03-12 6:40 ` [Intel-gfx] ✗ Fi.CI.SPARSE: " Patchwork
` (6 subsequent siblings)
16 siblings, 0 replies; 20+ messages in thread
From: Patchwork @ 2020-03-12 6:37 UTC (permalink / raw)
To: Vandita Kulkarni; +Cc: intel-gfx
== Series Details ==
Series: Add support for mipi dsi cmd mode (rev7)
URL : https://patchwork.freedesktop.org/series/69290/
State : warning
== Summary ==
$ dim checkpatch origin/drm-tip
ab22e3ce17b0 drm/i915/dsi: Configure transcoder operation for command mode.
caaa705c0348 drm/i915/dsi: Add vblank calculation for command mode
-:51: WARNING:LONG_LINE: line over 100 characters
#51: FILE: drivers/gpu/drm/i915/display/icl_dsi.c:876:
+ line_time_us = (htotal * (bpp / 8) * byte_clk_period_ns) / (1000 * intel_dsi->lane_count);
total: 0 errors, 1 warnings, 0 checks, 79 lines checked
3830ac46bbb4 drm/i915/dsi: Add cmd mode flags in display mode private flags
-:30: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#30: FILE: drivers/gpu/drm/i915/display/intel_display_types.h:648:
+#define I915_MODE_FLAG_DSI_USE_TE0 (1<<3)
^
-:32: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#32: FILE: drivers/gpu/drm/i915/display/intel_display_types.h:650:
+#define I915_MODE_FLAG_DSI_USE_TE1 (1<<4)
^
-:34: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#34: FILE: drivers/gpu/drm/i915/display/intel_display_types.h:652:
+#define I915_MODE_FLAG_DSI_PERIODIC_CMD_MODE (1<<5)
^
total: 0 errors, 0 warnings, 3 checks, 16 lines checked
2fd6820dac51 drm/i915/dsi: Add check for periodic command mode
6cddc733fda6 drm/i915/dsi: Use private flags to indicate TE in cmd mode
1e460ae1ec9b drm/i915/dsi: Configure TE interrupt for cmd mode
31f2e0015d6a drm/i915/dsi: Add TE handler for dsi cmd mode.
-:50: CHECK:UNNECESSARY_PARENTHESES: Unnecessary parentheses around 'val != CMD_MODE_NO_GATE'
#50: FILE: drivers/gpu/drm/i915/i915_irq.c:2292:
+ if ((val != CMD_MODE_NO_GATE) && (val != CMD_MODE_TE_GATE)) {
-:50: CHECK:UNNECESSARY_PARENTHESES: Unnecessary parentheses around 'val != CMD_MODE_TE_GATE'
#50: FILE: drivers/gpu/drm/i915/i915_irq.c:2292:
+ if ((val != CMD_MODE_NO_GATE) && (val != CMD_MODE_TE_GATE)) {
total: 0 errors, 0 warnings, 2 checks, 76 lines checked
813d63e4f22c drm/i915/dsi: Initiate fame request in cmd mode
0e6e0377bdd5 drm/i915/dsi: Clear the DSI IIR
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 20+ messages in thread* [Intel-gfx] ✗ Fi.CI.SPARSE: warning for Add support for mipi dsi cmd mode (rev7)
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
` (9 preceding siblings ...)
2020-03-12 6:37 ` [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for mipi dsi cmd mode (rev7) Patchwork
@ 2020-03-12 6:40 ` Patchwork
2020-03-12 7:00 ` [Intel-gfx] ✗ Fi.CI.BAT: failure " Patchwork
` (5 subsequent siblings)
16 siblings, 0 replies; 20+ messages in thread
From: Patchwork @ 2020-03-12 6:40 UTC (permalink / raw)
To: Vandita Kulkarni; +Cc: intel-gfx
== Series Details ==
Series: Add support for mipi dsi cmd mode (rev7)
URL : https://patchwork.freedesktop.org/series/69290/
State : warning
== Summary ==
$ dim sparse origin/drm-tip
Sparse version: v0.6.0
Commit: drm/i915/dsi: Configure transcoder operation for command mode.
Okay!
Commit: drm/i915/dsi: Add vblank calculation for command mode
Okay!
Commit: drm/i915/dsi: Add cmd mode flags in display mode private flags
Okay!
Commit: drm/i915/dsi: Add check for periodic command mode
Okay!
Commit: drm/i915/dsi: Use private flags to indicate TE in cmd mode
Okay!
Commit: drm/i915/dsi: Configure TE interrupt for cmd mode
Okay!
Commit: drm/i915/dsi: Add TE handler for dsi cmd mode.
-
+drivers/gpu/drm/i915/i915_irq.c:2265:6: warning: symbol 'gen11_dsi_te_interrupt_handler' was not declared. Should it be static?
Commit: drm/i915/dsi: Initiate fame request in cmd mode
Okay!
Commit: drm/i915/dsi: Clear the DSI IIR
Okay!
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 20+ messages in thread* [Intel-gfx] ✗ Fi.CI.BAT: failure for Add support for mipi dsi cmd mode (rev7)
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
` (10 preceding siblings ...)
2020-03-12 6:40 ` [Intel-gfx] ✗ Fi.CI.SPARSE: " Patchwork
@ 2020-03-12 7:00 ` Patchwork
2020-03-16 21:59 ` [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for mipi dsi cmd mode (rev8) Patchwork
` (4 subsequent siblings)
16 siblings, 0 replies; 20+ messages in thread
From: Patchwork @ 2020-03-12 7:00 UTC (permalink / raw)
To: Vandita Kulkarni; +Cc: intel-gfx
== Series Details ==
Series: Add support for mipi dsi cmd mode (rev7)
URL : https://patchwork.freedesktop.org/series/69290/
State : failure
== Summary ==
CI Bug Log - changes from CI_DRM_8125 -> Patchwork_16947
====================================================
Summary
-------
**FAILURE**
Serious unknown changes coming with Patchwork_16947 absolutely need to be
verified manually.
If you think the reported changes have nothing to do with the changes
introduced in Patchwork_16947, please notify your bug team to allow them
to document this new failure mode, which will reduce false positives in CI.
External URL: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16947/index.html
Possible new issues
-------------------
Here are the unknown changes that may have been introduced in Patchwork_16947:
### IGT changes ###
#### Possible regressions ####
* igt@i915_selftest@live@execlists:
- fi-cfl-guc: [PASS][1] -> [INCOMPLETE][2]
[1]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8125/fi-cfl-guc/igt@i915_selftest@live@execlists.html
[2]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16947/fi-cfl-guc/igt@i915_selftest@live@execlists.html
Known issues
------------
Here are the changes found in Patchwork_16947 that come from known issues:
### IGT changes ###
#### Issues hit ####
* igt@i915_selftest@live@hangcheck:
- fi-cfl-guc: [PASS][3] -> [DMESG-WARN][4] ([i915#1430])
[3]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8125/fi-cfl-guc/igt@i915_selftest@live@hangcheck.html
[4]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16947/fi-cfl-guc/igt@i915_selftest@live@hangcheck.html
#### Possible fixes ####
* igt@i915_selftest@live@execlists:
- fi-apl-guc: [INCOMPLETE][5] ([fdo#103927]) -> [PASS][6]
[5]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8125/fi-apl-guc/igt@i915_selftest@live@execlists.html
[6]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16947/fi-apl-guc/igt@i915_selftest@live@execlists.html
* igt@i915_selftest@live@hangcheck:
- fi-apl-guc: [DMESG-WARN][7] ([i915#1430]) -> [PASS][8]
[7]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8125/fi-apl-guc/igt@i915_selftest@live@hangcheck.html
[8]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16947/fi-apl-guc/igt@i915_selftest@live@hangcheck.html
#### Warnings ####
* igt@kms_chamelium@hdmi-hpd-fast:
- fi-kbl-7500u: [FAIL][9] ([fdo#111407]) -> [FAIL][10] ([i915#323])
[9]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8125/fi-kbl-7500u/igt@kms_chamelium@hdmi-hpd-fast.html
[10]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16947/fi-kbl-7500u/igt@kms_chamelium@hdmi-hpd-fast.html
[fdo#103927]: https://bugs.freedesktop.org/show_bug.cgi?id=103927
[fdo#111407]: https://bugs.freedesktop.org/show_bug.cgi?id=111407
[i915#1430]: https://gitlab.freedesktop.org/drm/intel/issues/1430
[i915#323]: https://gitlab.freedesktop.org/drm/intel/issues/323
Participating hosts (46 -> 42)
------------------------------
Additional (2): fi-skl-6770hq fi-kbl-7560u
Missing (6): fi-hsw-4200u fi-byt-squawks fi-bsw-cyan fi-ctg-p8600 fi-cfl-8109u fi-byt-clapper
Build changes
-------------
* CI: CI-20190529 -> None
* Linux: CI_DRM_8125 -> Patchwork_16947
CI-20190529: 20190529
CI_DRM_8125: 8fc697c3de927ae930efead8fd43032c6e5f5094 @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_5505: 8973d811f3fdfb4ace4aabab2095ce0309881648 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_16947: 0e6e0377bdd591df6643c6de36138e2581900f7e @ git://anongit.freedesktop.org/gfx-ci/linux
== Linux commits ==
0e6e0377bdd5 drm/i915/dsi: Clear the DSI IIR
813d63e4f22c drm/i915/dsi: Initiate fame request in cmd mode
31f2e0015d6a drm/i915/dsi: Add TE handler for dsi cmd mode.
1e460ae1ec9b drm/i915/dsi: Configure TE interrupt for cmd mode
6cddc733fda6 drm/i915/dsi: Use private flags to indicate TE in cmd mode
2fd6820dac51 drm/i915/dsi: Add check for periodic command mode
3830ac46bbb4 drm/i915/dsi: Add cmd mode flags in display mode private flags
caaa705c0348 drm/i915/dsi: Add vblank calculation for command mode
ab22e3ce17b0 drm/i915/dsi: Configure transcoder operation for command mode.
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16947/index.html
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 20+ messages in thread* [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for mipi dsi cmd mode (rev8)
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
` (11 preceding siblings ...)
2020-03-12 7:00 ` [Intel-gfx] ✗ Fi.CI.BAT: failure " Patchwork
@ 2020-03-16 21:59 ` Patchwork
2020-03-16 22:02 ` [Intel-gfx] ✗ Fi.CI.SPARSE: " Patchwork
` (3 subsequent siblings)
16 siblings, 0 replies; 20+ messages in thread
From: Patchwork @ 2020-03-16 21:59 UTC (permalink / raw)
To: Vandita Kulkarni; +Cc: intel-gfx
== Series Details ==
Series: Add support for mipi dsi cmd mode (rev8)
URL : https://patchwork.freedesktop.org/series/69290/
State : warning
== Summary ==
$ dim checkpatch origin/drm-tip
006bc864d36a drm/i915/dsi: Configure transcoder operation for command mode.
01f67de3b52d drm/i915/dsi: Add vblank calculation for command mode
-:51: WARNING:LONG_LINE: line over 100 characters
#51: FILE: drivers/gpu/drm/i915/display/icl_dsi.c:876:
+ line_time_us = (htotal * (bpp / 8) * byte_clk_period_ns) / (1000 * intel_dsi->lane_count);
total: 0 errors, 1 warnings, 0 checks, 79 lines checked
248f98d7878b drm/i915/dsi: Add cmd mode flags in display mode private flags
-:30: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#30: FILE: drivers/gpu/drm/i915/display/intel_display_types.h:648:
+#define I915_MODE_FLAG_DSI_USE_TE0 (1<<3)
^
-:32: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#32: FILE: drivers/gpu/drm/i915/display/intel_display_types.h:650:
+#define I915_MODE_FLAG_DSI_USE_TE1 (1<<4)
^
-:34: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#34: FILE: drivers/gpu/drm/i915/display/intel_display_types.h:652:
+#define I915_MODE_FLAG_DSI_PERIODIC_CMD_MODE (1<<5)
^
total: 0 errors, 0 warnings, 3 checks, 16 lines checked
1579eb831109 drm/i915/dsi: Add check for periodic command mode
c16239040c2e drm/i915/dsi: Use private flags to indicate TE in cmd mode
e943545f217e drm/i915/dsi: Configure TE interrupt for cmd mode
167b44070f5f drm/i915/dsi: Add TE handler for dsi cmd mode.
-:50: CHECK:UNNECESSARY_PARENTHESES: Unnecessary parentheses around 'val != CMD_MODE_NO_GATE'
#50: FILE: drivers/gpu/drm/i915/i915_irq.c:2292:
+ if ((val != CMD_MODE_NO_GATE) && (val != CMD_MODE_TE_GATE)) {
-:50: CHECK:UNNECESSARY_PARENTHESES: Unnecessary parentheses around 'val != CMD_MODE_TE_GATE'
#50: FILE: drivers/gpu/drm/i915/i915_irq.c:2292:
+ if ((val != CMD_MODE_NO_GATE) && (val != CMD_MODE_TE_GATE)) {
total: 0 errors, 0 warnings, 2 checks, 76 lines checked
ce4fc1ba719f drm/i915/dsi: Initiate fame request in cmd mode
43785a14fc4a drm/i915/dsi: Clear the DSI IIR
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 20+ messages in thread* [Intel-gfx] ✗ Fi.CI.SPARSE: warning for Add support for mipi dsi cmd mode (rev8)
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
` (12 preceding siblings ...)
2020-03-16 21:59 ` [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for mipi dsi cmd mode (rev8) Patchwork
@ 2020-03-16 22:02 ` Patchwork
2020-03-16 22:17 ` [Intel-gfx] ✗ Fi.CI.DOCS: " Patchwork
` (2 subsequent siblings)
16 siblings, 0 replies; 20+ messages in thread
From: Patchwork @ 2020-03-16 22:02 UTC (permalink / raw)
To: Vandita Kulkarni; +Cc: intel-gfx
== Series Details ==
Series: Add support for mipi dsi cmd mode (rev8)
URL : https://patchwork.freedesktop.org/series/69290/
State : warning
== Summary ==
$ dim sparse origin/drm-tip
Sparse version: v0.6.0
Commit: drm/i915/dsi: Configure transcoder operation for command mode.
Okay!
Commit: drm/i915/dsi: Add vblank calculation for command mode
Okay!
Commit: drm/i915/dsi: Add cmd mode flags in display mode private flags
Okay!
Commit: drm/i915/dsi: Add check for periodic command mode
Okay!
Commit: drm/i915/dsi: Use private flags to indicate TE in cmd mode
Okay!
Commit: drm/i915/dsi: Configure TE interrupt for cmd mode
Okay!
Commit: drm/i915/dsi: Add TE handler for dsi cmd mode.
-
+drivers/gpu/drm/i915/i915_irq.c:2265:6: warning: symbol 'gen11_dsi_te_interrupt_handler' was not declared. Should it be static?
Commit: drm/i915/dsi: Initiate fame request in cmd mode
Okay!
Commit: drm/i915/dsi: Clear the DSI IIR
Okay!
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 20+ messages in thread* [Intel-gfx] ✗ Fi.CI.DOCS: warning for Add support for mipi dsi cmd mode (rev8)
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
` (13 preceding siblings ...)
2020-03-16 22:02 ` [Intel-gfx] ✗ Fi.CI.SPARSE: " Patchwork
@ 2020-03-16 22:17 ` Patchwork
2020-03-16 22:23 ` [Intel-gfx] ✓ Fi.CI.BAT: success " Patchwork
2020-03-17 6:59 ` [Intel-gfx] ✓ Fi.CI.IGT: " Patchwork
16 siblings, 0 replies; 20+ messages in thread
From: Patchwork @ 2020-03-16 22:17 UTC (permalink / raw)
To: Vandita Kulkarni; +Cc: intel-gfx
== Series Details ==
Series: Add support for mipi dsi cmd mode (rev8)
URL : https://patchwork.freedesktop.org/series/69290/
State : warning
== Summary ==
$ make htmldocs 2>&1 > /dev/null | grep i915
Error: Cannot open file ./drivers/gpu/drm/i915/i915_gem_fence_reg.c
Error: Cannot open file ./drivers/gpu/drm/i915/i915_gem_fence_reg.c
Error: Cannot open file ./drivers/gpu/drm/i915/i915_gem_fence_reg.c
Error: Cannot open file ./drivers/gpu/drm/i915/i915_gem_fence_reg.c
WARNING: kernel-doc './scripts/kernel-doc -rst -enable-lineno -internal ./drivers/gpu/drm/i915/i915_gem_fence_reg.c' failed with return code 2
WARNING: kernel-doc './scripts/kernel-doc -rst -enable-lineno -function fence register handling ./drivers/gpu/drm/i915/i915_gem_fence_reg.c' failed with return code 1
WARNING: kernel-doc './scripts/kernel-doc -rst -enable-lineno -function tiling swizzling details ./drivers/gpu/drm/i915/i915_gem_fence_reg.c' failed with return code 1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 20+ messages in thread* [Intel-gfx] ✓ Fi.CI.BAT: success for Add support for mipi dsi cmd mode (rev8)
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
` (14 preceding siblings ...)
2020-03-16 22:17 ` [Intel-gfx] ✗ Fi.CI.DOCS: " Patchwork
@ 2020-03-16 22:23 ` Patchwork
2020-03-17 6:59 ` [Intel-gfx] ✓ Fi.CI.IGT: " Patchwork
16 siblings, 0 replies; 20+ messages in thread
From: Patchwork @ 2020-03-16 22:23 UTC (permalink / raw)
To: Vandita Kulkarni; +Cc: intel-gfx
== Series Details ==
Series: Add support for mipi dsi cmd mode (rev8)
URL : https://patchwork.freedesktop.org/series/69290/
State : success
== Summary ==
CI Bug Log - changes from CI_DRM_8138 -> Patchwork_16982
====================================================
Summary
-------
**SUCCESS**
No regressions found.
External URL: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/index.html
Known issues
------------
Here are the changes found in Patchwork_16982 that come from known issues:
### IGT changes ###
#### Issues hit ####
* igt@gem_exec_suspend@basic-s4-devices:
- fi-tgl-y: [PASS][1] -> [FAIL][2] ([CI#94])
[1]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/fi-tgl-y/igt@gem_exec_suspend@basic-s4-devices.html
[2]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/fi-tgl-y/igt@gem_exec_suspend@basic-s4-devices.html
* igt@kms_chamelium@dp-crc-fast:
- fi-kbl-7500u: [PASS][3] -> [FAIL][4] ([fdo#109635] / [i915#262])
[3]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/fi-kbl-7500u/igt@kms_chamelium@dp-crc-fast.html
[4]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/fi-kbl-7500u/igt@kms_chamelium@dp-crc-fast.html
#### Possible fixes ####
* igt@i915_selftest@live@perf:
- fi-bwr-2160: [INCOMPLETE][5] -> [PASS][6]
[5]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/fi-bwr-2160/igt@i915_selftest@live@perf.html
[6]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/fi-bwr-2160/igt@i915_selftest@live@perf.html
* igt@kms_chamelium@common-hpd-after-suspend:
- fi-cml-u2: [FAIL][7] ([i915#217]) -> [PASS][8]
[7]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/fi-cml-u2/igt@kms_chamelium@common-hpd-after-suspend.html
[8]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/fi-cml-u2/igt@kms_chamelium@common-hpd-after-suspend.html
[CI#94]: https://gitlab.freedesktop.org/gfx-ci/i915-infra/issues/94
[fdo#109635]: https://bugs.freedesktop.org/show_bug.cgi?id=109635
[i915#217]: https://gitlab.freedesktop.org/drm/intel/issues/217
[i915#262]: https://gitlab.freedesktop.org/drm/intel/issues/262
Participating hosts (40 -> 44)
------------------------------
Additional (8): fi-bdw-5557u fi-hsw-peppy fi-skl-6770hq fi-ilk-650 fi-gdg-551 fi-ivb-3770 fi-cfl-8109u fi-snb-2600
Missing (4): fi-byt-squawks fi-bsw-cyan fi-bdw-samus fi-hsw-4200u
Build changes
-------------
* CI: CI-20190529 -> None
* Linux: CI_DRM_8138 -> Patchwork_16982
CI-20190529: 20190529
CI_DRM_8138: 652084cff0971058d1acb1746001f89ef8ea7321 @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_5512: f6fef7eff6f121e5e89afd7e70116f471ccd5b8b @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_16982: 43785a14fc4abcd5137d04c291788f4efe141aeb @ git://anongit.freedesktop.org/gfx-ci/linux
== Linux commits ==
43785a14fc4a drm/i915/dsi: Clear the DSI IIR
ce4fc1ba719f drm/i915/dsi: Initiate fame request in cmd mode
167b44070f5f drm/i915/dsi: Add TE handler for dsi cmd mode.
e943545f217e drm/i915/dsi: Configure TE interrupt for cmd mode
c16239040c2e drm/i915/dsi: Use private flags to indicate TE in cmd mode
1579eb831109 drm/i915/dsi: Add check for periodic command mode
248f98d7878b drm/i915/dsi: Add cmd mode flags in display mode private flags
01f67de3b52d drm/i915/dsi: Add vblank calculation for command mode
006bc864d36a drm/i915/dsi: Configure transcoder operation for command mode.
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/index.html
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 20+ messages in thread* [Intel-gfx] ✓ Fi.CI.IGT: success for Add support for mipi dsi cmd mode (rev8)
2020-03-12 5:38 [Intel-gfx] [V8 0/9] Add support for mipi dsi cmd mode Vandita Kulkarni
` (15 preceding siblings ...)
2020-03-16 22:23 ` [Intel-gfx] ✓ Fi.CI.BAT: success " Patchwork
@ 2020-03-17 6:59 ` Patchwork
16 siblings, 0 replies; 20+ messages in thread
From: Patchwork @ 2020-03-17 6:59 UTC (permalink / raw)
To: Vandita Kulkarni; +Cc: intel-gfx
== Series Details ==
Series: Add support for mipi dsi cmd mode (rev8)
URL : https://patchwork.freedesktop.org/series/69290/
State : success
== Summary ==
CI Bug Log - changes from CI_DRM_8138_full -> Patchwork_16982_full
====================================================
Summary
-------
**SUCCESS**
No regressions found.
Possible new issues
-------------------
Here are the unknown changes that may have been introduced in Patchwork_16982_full:
### IGT changes ###
#### Suppressed ####
The following results come from untrusted machines, tests, or statuses.
They do not affect the overall result.
* {igt@sysfs_preempt_timeout@timeout@rcs0}:
- shard-skl: [PASS][1] -> [FAIL][2]
[1]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-skl1/igt@sysfs_preempt_timeout@timeout@rcs0.html
[2]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-skl7/igt@sysfs_preempt_timeout@timeout@rcs0.html
New tests
---------
New tests have been introduced between CI_DRM_8138_full and Patchwork_16982_full:
### New IGT tests (3) ###
* igt@sysfs_heartbeat_interval@off:
- Statuses :
- Exec time: [None] s
* igt@sysfs_heartbeat_interval@precise:
- Statuses :
- Exec time: [None] s
* igt@sysfs_preempt_timeout@idempotent:
- Statuses :
- Exec time: [None] s
Known issues
------------
Here are the changes found in Patchwork_16982_full that come from known issues:
### IGT changes ###
#### Issues hit ####
* igt@gem_ctx_isolation@vcs1-none:
- shard-iclb: [PASS][3] -> [SKIP][4] ([fdo#112080]) +6 similar issues
[3]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-iclb1/igt@gem_ctx_isolation@vcs1-none.html
[4]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-iclb5/igt@gem_ctx_isolation@vcs1-none.html
* igt@gem_ctx_persistence@close-replace-race:
- shard-skl: [PASS][5] -> [INCOMPLETE][6] ([i915#1402])
[5]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-skl8/igt@gem_ctx_persistence@close-replace-race.html
[6]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-skl6/igt@gem_ctx_persistence@close-replace-race.html
* igt@gem_ctx_shared@q-independent-vebox:
- shard-skl: [PASS][7] -> [FAIL][8] ([i915#935])
[7]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-skl1/igt@gem_ctx_shared@q-independent-vebox.html
[8]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-skl7/igt@gem_ctx_shared@q-independent-vebox.html
* igt@gem_exec_schedule@implicit-both-bsd:
- shard-iclb: [PASS][9] -> [SKIP][10] ([i915#677])
[9]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-iclb5/igt@gem_exec_schedule@implicit-both-bsd.html
[10]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-iclb4/igt@gem_exec_schedule@implicit-both-bsd.html
* igt@gem_exec_schedule@implicit-read-write-render:
- shard-snb: [PASS][11] -> [INCOMPLETE][12] ([i915#82])
[11]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-snb2/igt@gem_exec_schedule@implicit-read-write-render.html
[12]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-snb5/igt@gem_exec_schedule@implicit-read-write-render.html
* igt@gem_exec_schedule@implicit-write-read-bsd2:
- shard-iclb: [PASS][13] -> [SKIP][14] ([fdo#109276] / [i915#677])
[13]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-iclb1/igt@gem_exec_schedule@implicit-write-read-bsd2.html
[14]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-iclb5/igt@gem_exec_schedule@implicit-write-read-bsd2.html
* igt@gem_exec_schedule@preempt-queue-bsd:
- shard-iclb: [PASS][15] -> [SKIP][16] ([fdo#112146]) +2 similar issues
[15]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-iclb7/igt@gem_exec_schedule@preempt-queue-bsd.html
[16]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-iclb2/igt@gem_exec_schedule@preempt-queue-bsd.html
* igt@gem_ppgtt@flink-and-close-vma-leak:
- shard-glk: [PASS][17] -> [FAIL][18] ([i915#644])
[17]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-glk4/igt@gem_ppgtt@flink-and-close-vma-leak.html
[18]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-glk6/igt@gem_ppgtt@flink-and-close-vma-leak.html
- shard-apl: [PASS][19] -> [FAIL][20] ([i915#644])
[19]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-apl8/igt@gem_ppgtt@flink-and-close-vma-leak.html
[20]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-apl3/igt@gem_ppgtt@flink-and-close-vma-leak.html
* igt@kms_cursor_crc@pipe-a-cursor-128x128-random:
- shard-skl: [PASS][21] -> [FAIL][22] ([i915#54])
[21]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-skl2/igt@kms_cursor_crc@pipe-a-cursor-128x128-random.html
[22]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-skl4/igt@kms_cursor_crc@pipe-a-cursor-128x128-random.html
- shard-kbl: [PASS][23] -> [FAIL][24] ([i915#54])
[23]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-kbl6/igt@kms_cursor_crc@pipe-a-cursor-128x128-random.html
[24]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-kbl7/igt@kms_cursor_crc@pipe-a-cursor-128x128-random.html
- shard-apl: [PASS][25] -> [FAIL][26] ([i915#54])
[25]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-apl3/igt@kms_cursor_crc@pipe-a-cursor-128x128-random.html
[26]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-apl3/igt@kms_cursor_crc@pipe-a-cursor-128x128-random.html
* igt@kms_cursor_crc@pipe-a-cursor-suspend:
- shard-kbl: [PASS][27] -> [DMESG-WARN][28] ([i915#180]) +2 similar issues
[27]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-kbl3/igt@kms_cursor_crc@pipe-a-cursor-suspend.html
[28]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-kbl7/igt@kms_cursor_crc@pipe-a-cursor-suspend.html
* igt@kms_cursor_crc@pipe-b-cursor-suspend:
- shard-apl: [PASS][29] -> [DMESG-WARN][30] ([i915#180]) +1 similar issue
[29]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-apl4/igt@kms_cursor_crc@pipe-b-cursor-suspend.html
[30]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-apl1/igt@kms_cursor_crc@pipe-b-cursor-suspend.html
* igt@kms_flip@2x-wf_vblank-ts-check-interruptible:
- shard-glk: [PASS][31] -> [FAIL][32] ([i915#34])
[31]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-glk5/igt@kms_flip@2x-wf_vblank-ts-check-interruptible.html
[32]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-glk1/igt@kms_flip@2x-wf_vblank-ts-check-interruptible.html
* igt@kms_flip@flip-vs-suspend:
- shard-skl: [PASS][33] -> [INCOMPLETE][34] ([i915#221])
[33]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-skl5/igt@kms_flip@flip-vs-suspend.html
[34]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-skl5/igt@kms_flip@flip-vs-suspend.html
* igt@kms_flip@plain-flip-ts-check:
- shard-skl: [PASS][35] -> [FAIL][36] ([i915#34])
[35]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-skl6/igt@kms_flip@plain-flip-ts-check.html
[36]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-skl6/igt@kms_flip@plain-flip-ts-check.html
* igt@kms_frontbuffer_tracking@fbc-2p-scndscrn-spr-indfb-move:
- shard-glk: [PASS][37] -> [FAIL][38] ([i915#49])
[37]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-glk6/igt@kms_frontbuffer_tracking@fbc-2p-scndscrn-spr-indfb-move.html
[38]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-glk3/igt@kms_frontbuffer_tracking@fbc-2p-scndscrn-spr-indfb-move.html
* igt@kms_hdr@bpc-switch-suspend:
- shard-skl: [PASS][39] -> [FAIL][40] ([i915#1188]) +1 similar issue
[39]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-skl7/igt@kms_hdr@bpc-switch-suspend.html
[40]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-skl1/igt@kms_hdr@bpc-switch-suspend.html
* igt@kms_psr2_su@page_flip:
- shard-iclb: [PASS][41] -> [SKIP][42] ([fdo#109642] / [fdo#111068])
[41]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-iclb2/igt@kms_psr2_su@page_flip.html
[42]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-iclb6/igt@kms_psr2_su@page_flip.html
* igt@kms_psr@psr2_cursor_blt:
- shard-iclb: [PASS][43] -> [SKIP][44] ([fdo#109441])
[43]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-iclb2/igt@kms_psr@psr2_cursor_blt.html
[44]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-iclb1/igt@kms_psr@psr2_cursor_blt.html
* igt@kms_vblank@pipe-b-query-idle-hang:
- shard-skl: [PASS][45] -> [SKIP][46] ([fdo#109271]) +1 similar issue
[45]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-skl1/igt@kms_vblank@pipe-b-query-idle-hang.html
[46]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-skl7/igt@kms_vblank@pipe-b-query-idle-hang.html
* igt@prime_busy@after-bsd2:
- shard-iclb: [PASS][47] -> [SKIP][48] ([fdo#109276]) +4 similar issues
[47]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-iclb2/igt@prime_busy@after-bsd2.html
[48]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-iclb6/igt@prime_busy@after-bsd2.html
#### Possible fixes ####
* igt@gem_ctx_persistence@close-replace-race:
- shard-tglb: [INCOMPLETE][49] ([i915#1402]) -> [PASS][50]
[49]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-tglb1/igt@gem_ctx_persistence@close-replace-race.html
[50]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-tglb1/igt@gem_ctx_persistence@close-replace-race.html
* igt@gem_exec_schedule@implicit-both-bsd1:
- shard-iclb: [SKIP][51] ([fdo#109276] / [i915#677]) -> [PASS][52]
[51]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-iclb3/igt@gem_exec_schedule@implicit-both-bsd1.html
[52]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-iclb1/igt@gem_exec_schedule@implicit-both-bsd1.html
* igt@gem_exec_schedule@pi-distinct-iova-render:
- shard-skl: [DMESG-WARN][53] ([i915#836]) -> [PASS][54]
[53]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-skl10/igt@gem_exec_schedule@pi-distinct-iova-render.html
[54]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-skl2/igt@gem_exec_schedule@pi-distinct-iova-render.html
* igt@gem_exec_schedule@pi-shared-iova-bsd:
- shard-iclb: [SKIP][55] ([i915#677]) -> [PASS][56]
[55]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-iclb2/igt@gem_exec_schedule@pi-shared-iova-bsd.html
[56]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-iclb6/igt@gem_exec_schedule@pi-shared-iova-bsd.html
* igt@gem_exec_schedule@preempt-queue-contexts-render:
- shard-skl: [FAIL][57] -> [PASS][58] +3 similar issues
[57]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-skl3/igt@gem_exec_schedule@preempt-queue-contexts-render.html
[58]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-skl10/igt@gem_exec_schedule@preempt-queue-contexts-render.html
* igt@gem_exec_schedule@reorder-wide-bsd:
- shard-iclb: [SKIP][59] ([fdo#112146]) -> [PASS][60] +1 similar issue
[59]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-iclb2/igt@gem_exec_schedule@reorder-wide-bsd.html
[60]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-iclb6/igt@gem_exec_schedule@reorder-wide-bsd.html
* igt@gem_softpin@noreloc-s3:
- shard-snb: [DMESG-WARN][61] ([i915#42]) -> [PASS][62]
[61]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-snb5/igt@gem_softpin@noreloc-s3.html
[62]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-snb6/igt@gem_softpin@noreloc-s3.html
* igt@i915_pm_dc@dc6-psr:
- shard-iclb: [FAIL][63] ([i915#454]) -> [PASS][64]
[63]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-iclb6/igt@i915_pm_dc@dc6-psr.html
[64]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-iclb8/igt@i915_pm_dc@dc6-psr.html
* igt@i915_pm_rps@reset:
- shard-iclb: [FAIL][65] ([i915#413]) -> [PASS][66]
[65]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-iclb3/igt@i915_pm_rps@reset.html
[66]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-iclb7/igt@i915_pm_rps@reset.html
* igt@i915_pm_rps@waitboost:
- shard-tglb: [FAIL][67] ([i915#413]) -> [PASS][68]
[67]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-tglb3/igt@i915_pm_rps@waitboost.html
[68]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-tglb3/igt@i915_pm_rps@waitboost.html
* igt@kms_color@pipe-c-ctm-0-5:
- shard-skl: [FAIL][69] ([i915#182]) -> [PASS][70]
[69]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-skl1/igt@kms_color@pipe-c-ctm-0-5.html
[70]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-skl3/igt@kms_color@pipe-c-ctm-0-5.html
* igt@kms_cursor_legacy@flip-vs-cursor-atomic-transitions-varying-size:
- shard-skl: [FAIL][71] ([IGT#5]) -> [PASS][72]
[71]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-skl1/igt@kms_cursor_legacy@flip-vs-cursor-atomic-transitions-varying-size.html
[72]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-skl3/igt@kms_cursor_legacy@flip-vs-cursor-atomic-transitions-varying-size.html
* igt@kms_flip@flip-vs-suspend-interruptible:
- shard-apl: [DMESG-WARN][73] ([i915#180]) -> [PASS][74] +1 similar issue
[73]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-apl4/igt@kms_flip@flip-vs-suspend-interruptible.html
[74]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-apl7/igt@kms_flip@flip-vs-suspend-interruptible.html
* igt@kms_flip@plain-flip-ts-check-interruptible:
- shard-glk: [FAIL][75] ([i915#34]) -> [PASS][76]
[75]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-glk2/igt@kms_flip@plain-flip-ts-check-interruptible.html
[76]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-glk4/igt@kms_flip@plain-flip-ts-check-interruptible.html
* igt@kms_plane@plane-panning-bottom-right-suspend-pipe-c-planes:
- shard-skl: [INCOMPLETE][77] ([i915#69]) -> [PASS][78]
[77]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-skl1/igt@kms_plane@plane-panning-bottom-right-suspend-pipe-c-planes.html
[78]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-skl3/igt@kms_plane@plane-panning-bottom-right-suspend-pipe-c-planes.html
- shard-kbl: [DMESG-WARN][79] ([i915#180]) -> [PASS][80]
[79]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-kbl1/igt@kms_plane@plane-panning-bottom-right-suspend-pipe-c-planes.html
[80]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-kbl2/igt@kms_plane@plane-panning-bottom-right-suspend-pipe-c-planes.html
* igt@kms_plane_alpha_blend@pipe-c-constant-alpha-min:
- shard-skl: [FAIL][81] ([fdo#108145]) -> [PASS][82] +1 similar issue
[81]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-skl3/igt@kms_plane_alpha_blend@pipe-c-constant-alpha-min.html
[82]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-skl2/igt@kms_plane_alpha_blend@pipe-c-constant-alpha-min.html
* igt@kms_plane_alpha_blend@pipe-c-coverage-7efc:
- shard-skl: [FAIL][83] ([fdo#108145] / [i915#265]) -> [PASS][84] +1 similar issue
[83]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-skl10/igt@kms_plane_alpha_blend@pipe-c-coverage-7efc.html
[84]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-skl4/igt@kms_plane_alpha_blend@pipe-c-coverage-7efc.html
* igt@kms_psr@psr2_suspend:
- shard-iclb: [SKIP][85] ([fdo#109441]) -> [PASS][86]
[85]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-iclb4/igt@kms_psr@psr2_suspend.html
[86]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-iclb2/igt@kms_psr@psr2_suspend.html
* igt@kms_setmode@basic:
- shard-apl: [FAIL][87] ([i915#31]) -> [PASS][88]
[87]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-apl1/igt@kms_setmode@basic.html
[88]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-apl8/igt@kms_setmode@basic.html
- shard-glk: [FAIL][89] ([i915#31]) -> [PASS][90]
[89]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-glk7/igt@kms_setmode@basic.html
[90]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-glk4/igt@kms_setmode@basic.html
* igt@perf_pmu@busy-no-semaphores-vcs1:
- shard-iclb: [SKIP][91] ([fdo#112080]) -> [PASS][92] +7 similar issues
[91]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-iclb6/igt@perf_pmu@busy-no-semaphores-vcs1.html
[92]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-iclb4/igt@perf_pmu@busy-no-semaphores-vcs1.html
* igt@prime_busy@hang-bsd2:
- shard-iclb: [SKIP][93] ([fdo#109276]) -> [PASS][94] +10 similar issues
[93]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-iclb3/igt@prime_busy@hang-bsd2.html
[94]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-iclb1/igt@prime_busy@hang-bsd2.html
#### Warnings ####
* igt@gem_ctx_persistence@close-replace-race:
- shard-kbl: [TIMEOUT][95] ([i915#1340]) -> [INCOMPLETE][96] ([i915#1402])
[95]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-kbl4/igt@gem_ctx_persistence@close-replace-race.html
[96]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-kbl2/igt@gem_ctx_persistence@close-replace-race.html
* igt@i915_pm_dc@dc3co-vpb-simulation:
- shard-iclb: [SKIP][97] ([i915#588]) -> [SKIP][98] ([i915#658])
[97]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-iclb2/igt@i915_pm_dc@dc3co-vpb-simulation.html
[98]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-iclb6/igt@i915_pm_dc@dc3co-vpb-simulation.html
* igt@i915_pm_dc@dc6-psr:
- shard-tglb: [FAIL][99] ([i915#454]) -> [SKIP][100] ([i915#468])
[99]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-tglb7/igt@i915_pm_dc@dc6-psr.html
[100]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-tglb2/igt@i915_pm_dc@dc6-psr.html
* igt@i915_pm_rpm@dpms-non-lpsp:
- shard-snb: [INCOMPLETE][101] ([i915#82]) -> [SKIP][102] ([fdo#109271])
[101]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-snb5/igt@i915_pm_rpm@dpms-non-lpsp.html
[102]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-snb4/igt@i915_pm_rpm@dpms-non-lpsp.html
* igt@runner@aborted:
- shard-kbl: [FAIL][103] ([i915#92]) -> ([FAIL][104], [FAIL][105]) ([i915#1389] / [i915#1402] / [i915#92])
[103]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-kbl7/igt@runner@aborted.html
[104]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-kbl2/igt@runner@aborted.html
[105]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-kbl2/igt@runner@aborted.html
- shard-skl: [FAIL][106] ([i915#69]) -> [FAIL][107] ([i915#1402] / [i915#69])
[106]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_8138/shard-skl10/igt@runner@aborted.html
[107]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/shard-skl6/igt@runner@aborted.html
{name}: This element is suppressed. This means it is ignored when computing
the status of the difference (SUCCESS, WARNING, or FAILURE).
[IGT#5]: https://gitlab.freedesktop.org/drm/igt-gpu-tools/issues/5
[fdo#108145]: https://bugs.freedesktop.org/show_bug.cgi?id=108145
[fdo#109271]: https://bugs.freedesktop.org/show_bug.cgi?id=109271
[fdo#109276]: https://bugs.freedesktop.org/show_bug.cgi?id=109276
[fdo#109441]: https://bugs.freedesktop.org/show_bug.cgi?id=109441
[fdo#109642]: https://bugs.freedesktop.org/show_bug.cgi?id=109642
[fdo#111068]: https://bugs.freedesktop.org/show_bug.cgi?id=111068
[fdo#112080]: https://bugs.freedesktop.org/show_bug.cgi?id=112080
[fdo#112146]: https://bugs.freedesktop.org/show_bug.cgi?id=112146
[i915#1188]: https://gitlab.freedesktop.org/drm/intel/issues/1188
[i915#1340]: https://gitlab.freedesktop.org/drm/intel/issues/1340
[i915#1389]: https://gitlab.freedesktop.org/drm/intel/issues/1389
[i915#1402]: https://gitlab.freedesktop.org/drm/intel/issues/1402
[i915#180]: https://gitlab.freedesktop.org/drm/intel/issues/180
[i915#182]: https://gitlab.freedesktop.org/drm/intel/issues/182
[i915#221]: https://gitlab.freedesktop.org/drm/intel/issues/221
[i915#265]: https://gitlab.freedesktop.org/drm/intel/issues/265
[i915#31]: https://gitlab.freedesktop.org/drm/intel/issues/31
[i915#34]: https://gitlab.freedesktop.org/drm/intel/issues/34
[i915#413]: https://gitlab.freedesktop.org/drm/intel/issues/413
[i915#42]: https://gitlab.freedesktop.org/drm/intel/issues/42
[i915#454]: https://gitlab.freedesktop.org/drm/intel/issues/454
[i915#468]: https://gitlab.freedesktop.org/drm/intel/issues/468
[i915#49]: https://gitlab.freedesktop.org/drm/intel/issues/49
[i915#54]: https://gitlab.freedesktop.org/drm/intel/issues/54
[i915#588]: https://gitlab.freedesktop.org/drm/intel/issues/588
[i915#644]: https://gitlab.freedesktop.org/drm/intel/issues/644
[i915#658]: https://gitlab.freedesktop.org/drm/intel/issues/658
[i915#677]: https://gitlab.freedesktop.org/drm/intel/issues/677
[i915#69]: https://gitlab.freedesktop.org/drm/intel/issues/69
[i915#82]: https://gitlab.freedesktop.org/drm/intel/issues/82
[i915#836]: https://gitlab.freedesktop.org/drm/intel/issues/836
[i915#92]: https://gitlab.freedesktop.org/drm/intel/issues/92
[i915#935]: https://gitlab.freedesktop.org/drm/intel/issues/935
Participating hosts (10 -> 10)
------------------------------
No changes in participating hosts
Build changes
-------------
* CI: CI-20190529 -> None
* Linux: CI_DRM_8138 -> Patchwork_16982
CI-20190529: 20190529
CI_DRM_8138: 652084cff0971058d1acb1746001f89ef8ea7321 @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_5512: f6fef7eff6f121e5e89afd7e70116f471ccd5b8b @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_16982: 43785a14fc4abcd5137d04c291788f4efe141aeb @ git://anongit.freedesktop.org/gfx-ci/linux
piglit_4509: fdc5a4ca11124ab8413c7988896eec4c97336694 @ git://anongit.freedesktop.org/piglit
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_16982/index.html
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 20+ messages in thread