* [PATCH v3 1/2] KVM: LAPIC: Optimize timer latency consider world switch time @ 2019-06-12 9:40 Wanpeng Li 2019-06-12 9:40 ` [PATCH v3 2/2] KVM: LAPIC: remove the trailing newline used in the fmt parameter of TP_printk Wanpeng Li 2019-06-12 15:14 ` [PATCH v3 1/2] KVM: LAPIC: Optimize timer latency consider world switch time Sean Christopherson 0 siblings, 2 replies; 7+ messages in thread From: Wanpeng Li @ 2019-06-12 9:40 UTC (permalink / raw) To: linux-kernel, kvm Cc: Paolo Bonzini, Radim Krčmář, Sean Christopherson From: Wanpeng Li <wanpengli@tencent.com> Advance lapic timer tries to hidden the hypervisor overhead between the host emulated timer fires and the guest awares the timer is fired. However, even though after more sustaining optimizations, kvm-unit-tests/tscdeadline_latency still awares ~1000 cycles latency since we lost the time between the end of wait_lapic_expire and the guest awares the timer is fired. There are codes between the end of wait_lapic_expire and the world switch, furthermore, the world switch itself also has overhead. Actually the guest_tsc is equal to the target deadline time in wait_lapic_expire is too late, guest will aware the latency between the end of wait_lapic_expire() and after vmentry to the guest. This patch takes this time into consideration. The vmentry+vmexit time which is measured by kvm-unit-tests/vmexit.falt is 1800 cycles on my 2.5GHz Skylake server, the vmentry_advance_ns module parameter default value is 300ns, it can be tuned/reworked in the further. This patch can reduce average cyclictest latency from 3us to 2us on Skylake server. (guest w/ nohz=off, idle=poll, host w/ preemption_timer=N, the cyclictest latency is not too sensitive when preemption_timer=Y for this optimization in my testing). Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Wanpeng Li <wanpengli@tencent.com> --- v2 -> v3: * read-only module parameter * get_vmentry_advance_cycles() not inline v1 -> v2: * rename get_vmentry_advance_delta to get_vmentry_advance_cycles * cache vmentry_advance_cycles by setting param bit 0 * add param max limit arch/x86/kvm/lapic.c | 33 ++++++++++++++++++++++++++++++--- arch/x86/kvm/lapic.h | 3 +++ arch/x86/kvm/vmx/vmx.c | 2 +- arch/x86/kvm/x86.c | 8 ++++++++ arch/x86/kvm/x86.h | 2 ++ 5 files changed, 44 insertions(+), 4 deletions(-) diff --git a/arch/x86/kvm/lapic.c b/arch/x86/kvm/lapic.c index fcf42a3..c6d76f9 100644 --- a/arch/x86/kvm/lapic.c +++ b/arch/x86/kvm/lapic.c @@ -1531,6 +1531,33 @@ static inline void adjust_lapic_timer_advance(struct kvm_vcpu *vcpu, apic->lapic_timer.timer_advance_ns = timer_advance_ns; } +u64 compute_vmentry_advance_cycles(struct kvm_vcpu *vcpu) +{ + u64 cycles; + struct kvm_lapic *apic = vcpu->arch.apic; + + cycles = vmentry_advance_ns * vcpu->arch.virtual_tsc_khz; + do_div(cycles, 1000000); + + apic->lapic_timer.vmentry_advance_cycles = cycles; + + return cycles; +} + +u64 get_vmentry_advance_cycles(struct kvm_vcpu *vcpu) +{ + struct kvm_lapic *apic = vcpu->arch.apic; + + if (unlikely(!vmentry_advance_ns)) + return 0; + + if (likely(apic->lapic_timer.vmentry_advance_cycles)) + return apic->lapic_timer.vmentry_advance_cycles; + + return compute_vmentry_advance_cycles(vcpu); +} +EXPORT_SYMBOL_GPL(get_vmentry_advance_cycles); + void kvm_wait_lapic_expire(struct kvm_vcpu *vcpu) { struct kvm_lapic *apic = vcpu->arch.apic; @@ -1544,7 +1571,7 @@ void kvm_wait_lapic_expire(struct kvm_vcpu *vcpu) tsc_deadline = apic->lapic_timer.expired_tscdeadline; apic->lapic_timer.expired_tscdeadline = 0; - guest_tsc = kvm_read_l1_tsc(vcpu, rdtsc()); + guest_tsc = kvm_read_l1_tsc(vcpu, rdtsc()) + get_vmentry_advance_cycles(vcpu); apic->lapic_timer.advance_expire_delta = guest_tsc - tsc_deadline; if (guest_tsc < tsc_deadline) @@ -1572,7 +1599,7 @@ static void start_sw_tscdeadline(struct kvm_lapic *apic) local_irq_save(flags); now = ktime_get(); - guest_tsc = kvm_read_l1_tsc(vcpu, rdtsc()); + guest_tsc = kvm_read_l1_tsc(vcpu, rdtsc()) + get_vmentry_advance_cycles(vcpu); ns = (tscdeadline - guest_tsc) * 1000000ULL; do_div(ns, this_tsc_khz); @@ -2329,7 +2356,7 @@ int kvm_create_lapic(struct kvm_vcpu *vcpu, int timer_advance_ns) apic->lapic_timer.timer_advance_ns = timer_advance_ns; apic->lapic_timer.timer_advance_adjust_done = true; } - + apic->lapic_timer.vmentry_advance_cycles = 0; /* * APIC is created enabled. This will prevent kvm_lapic_set_base from diff --git a/arch/x86/kvm/lapic.h b/arch/x86/kvm/lapic.h index f974a3d..fb32e69 100644 --- a/arch/x86/kvm/lapic.h +++ b/arch/x86/kvm/lapic.h @@ -33,6 +33,7 @@ struct kvm_timer { u64 expired_tscdeadline; u32 timer_advance_ns; s64 advance_expire_delta; + u64 vmentry_advance_cycles; atomic_t pending; /* accumulated triggered timers */ bool hv_timer_in_use; bool timer_advance_adjust_done; @@ -221,6 +222,8 @@ static inline int kvm_lapic_latched_init(struct kvm_vcpu *vcpu) bool kvm_apic_pending_eoi(struct kvm_vcpu *vcpu, int vector); void kvm_wait_lapic_expire(struct kvm_vcpu *vcpu); +u64 compute_vmentry_advance_cycles(struct kvm_vcpu *vcpu); +u64 get_vmentry_advance_cycles(struct kvm_vcpu *vcpu); bool kvm_intr_is_single_vcpu_fast(struct kvm *kvm, struct kvm_lapic_irq *irq, struct kvm_vcpu **dest_vcpu); diff --git a/arch/x86/kvm/vmx/vmx.c b/arch/x86/kvm/vmx/vmx.c index 0861c71..0751a44 100644 --- a/arch/x86/kvm/vmx/vmx.c +++ b/arch/x86/kvm/vmx/vmx.c @@ -7041,7 +7041,7 @@ static int vmx_set_hv_timer(struct kvm_vcpu *vcpu, u64 guest_deadline_tsc, vmx = to_vmx(vcpu); tscl = rdtsc(); - guest_tscl = kvm_read_l1_tsc(vcpu, tscl); + guest_tscl = kvm_read_l1_tsc(vcpu, tscl) + get_vmentry_advance_cycles(vcpu); delta_tsc = max(guest_deadline_tsc, guest_tscl) - guest_tscl; lapic_timer_advance_cycles = nsec_to_cycles(vcpu, ktimer->timer_advance_ns); diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c index 553c292..4b983bb 100644 --- a/arch/x86/kvm/x86.c +++ b/arch/x86/kvm/x86.c @@ -145,6 +145,12 @@ module_param(tsc_tolerance_ppm, uint, S_IRUGO | S_IWUSR); static int __read_mostly lapic_timer_advance_ns = -1; module_param(lapic_timer_advance_ns, int, S_IRUGO | S_IWUSR); +/* + * lapic timer vmentry advance (tscdeadline mode only) in nanoseconds. + */ +u32 __read_mostly vmentry_advance_ns = 300; +module_param(vmentry_advance_ns, uint, S_IRUGO); + static bool __read_mostly vector_hashing = true; module_param(vector_hashing, bool, S_IRUGO); @@ -1592,6 +1598,8 @@ static int kvm_set_tsc_khz(struct kvm_vcpu *vcpu, u32 user_tsc_khz) kvm_get_time_scale(user_tsc_khz * 1000LL, NSEC_PER_SEC, &vcpu->arch.virtual_tsc_shift, &vcpu->arch.virtual_tsc_mult); + if (vcpu->arch.apic && user_tsc_khz != vcpu->arch.virtual_tsc_khz) + compute_vmentry_advance_cycles(vcpu); vcpu->arch.virtual_tsc_khz = user_tsc_khz; /* diff --git a/arch/x86/kvm/x86.h b/arch/x86/kvm/x86.h index a470ff0..2174355 100644 --- a/arch/x86/kvm/x86.h +++ b/arch/x86/kvm/x86.h @@ -294,6 +294,8 @@ extern u64 kvm_supported_xcr0(void); extern unsigned int min_timer_period_us; +extern unsigned int vmentry_advance_ns; + extern bool enable_vmware_backdoor; extern struct static_key kvm_no_apic_vcpu; -- 2.7.4 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v3 2/2] KVM: LAPIC: remove the trailing newline used in the fmt parameter of TP_printk 2019-06-12 9:40 [PATCH v3 1/2] KVM: LAPIC: Optimize timer latency consider world switch time Wanpeng Li @ 2019-06-12 9:40 ` Wanpeng Li 2019-06-12 15:14 ` [PATCH v3 1/2] KVM: LAPIC: Optimize timer latency consider world switch time Sean Christopherson 1 sibling, 0 replies; 7+ messages in thread From: Wanpeng Li @ 2019-06-12 9:40 UTC (permalink / raw) To: linux-kernel, kvm; +Cc: Paolo Bonzini, Radim Krčmář From: Wanpeng Li <wanpengli@tencent.com> The trailing newlines will lead to extra newlines in the trace file which looks like the following output, so remove it. qemu-system-x86-15695 [002] ...1 15774.839240: kvm_hv_timer_state: vcpu_id 0 hv_timer 1 qemu-system-x86-15695 [002] ...1 15774.839309: kvm_hv_timer_state: vcpu_id 0 hv_timer 1 Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Wanpeng Li <wanpengli@tencent.com> --- arch/x86/kvm/trace.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kvm/trace.h b/arch/x86/kvm/trace.h index 4d47a26..b5c831e 100644 --- a/arch/x86/kvm/trace.h +++ b/arch/x86/kvm/trace.h @@ -1365,7 +1365,7 @@ TRACE_EVENT(kvm_hv_timer_state, __entry->vcpu_id = vcpu_id; __entry->hv_timer_in_use = hv_timer_in_use; ), - TP_printk("vcpu_id %x hv_timer %x\n", + TP_printk("vcpu_id %x hv_timer %x", __entry->vcpu_id, __entry->hv_timer_in_use) ); -- 2.7.4 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v3 1/2] KVM: LAPIC: Optimize timer latency consider world switch time 2019-06-12 9:40 [PATCH v3 1/2] KVM: LAPIC: Optimize timer latency consider world switch time Wanpeng Li 2019-06-12 9:40 ` [PATCH v3 2/2] KVM: LAPIC: remove the trailing newline used in the fmt parameter of TP_printk Wanpeng Li @ 2019-06-12 15:14 ` Sean Christopherson 2019-06-12 19:22 ` Radim Krčmář 2019-06-13 1:50 ` Wanpeng Li 1 sibling, 2 replies; 7+ messages in thread From: Sean Christopherson @ 2019-06-12 15:14 UTC (permalink / raw) To: Wanpeng Li; +Cc: linux-kernel, kvm, Paolo Bonzini, Radim Krčmář On Wed, Jun 12, 2019 at 05:40:18PM +0800, Wanpeng Li wrote: > From: Wanpeng Li <wanpengli@tencent.com> > > Advance lapic timer tries to hidden the hypervisor overhead between the > host emulated timer fires and the guest awares the timer is fired. However, > even though after more sustaining optimizations, kvm-unit-tests/tscdeadline_latency > still awares ~1000 cycles latency since we lost the time between the end of > wait_lapic_expire and the guest awares the timer is fired. There are > codes between the end of wait_lapic_expire and the world switch, furthermore, > the world switch itself also has overhead. Actually the guest_tsc is equal > to the target deadline time in wait_lapic_expire is too late, guest will > aware the latency between the end of wait_lapic_expire() and after vmentry > to the guest. This patch takes this time into consideration. > > The vmentry+vmexit time which is measured by kvm-unit-tests/vmexit.falt is > 1800 cycles on my 2.5GHz Skylake server, the vmentry_advance_ns module > parameter default value is 300ns, it can be tuned/reworked in the further. > This patch can reduce average cyclictest latency from 3us to 2us on Skylake > server. (guest w/ nohz=off, idle=poll, host w/ preemption_timer=N, the > cyclictest latency is not too sensitive when preemption_timer=Y for this > optimization in my testing). > > Cc: Paolo Bonzini <pbonzini@redhat.com> > Cc: Radim Krčmář <rkrcmar@redhat.com> > Cc: Sean Christopherson <sean.j.christopherson@intel.com> > Signed-off-by: Wanpeng Li <wanpengli@tencent.com> > --- > v2 -> v3: > * read-only module parameter > * get_vmentry_advance_cycles() not inline > v1 -> v2: > * rename get_vmentry_advance_delta to get_vmentry_advance_cycles > * cache vmentry_advance_cycles by setting param bit 0 > * add param max limit > > arch/x86/kvm/lapic.c | 33 ++++++++++++++++++++++++++++++--- > arch/x86/kvm/lapic.h | 3 +++ > arch/x86/kvm/vmx/vmx.c | 2 +- > arch/x86/kvm/x86.c | 8 ++++++++ > arch/x86/kvm/x86.h | 2 ++ > 5 files changed, 44 insertions(+), 4 deletions(-) > > diff --git a/arch/x86/kvm/lapic.c b/arch/x86/kvm/lapic.c > index fcf42a3..c6d76f9 100644 > --- a/arch/x86/kvm/lapic.c > +++ b/arch/x86/kvm/lapic.c > @@ -1531,6 +1531,33 @@ static inline void adjust_lapic_timer_advance(struct kvm_vcpu *vcpu, > apic->lapic_timer.timer_advance_ns = timer_advance_ns; > } > > +u64 compute_vmentry_advance_cycles(struct kvm_vcpu *vcpu) > +{ > + u64 cycles; > + struct kvm_lapic *apic = vcpu->arch.apic; > + > + cycles = vmentry_advance_ns * vcpu->arch.virtual_tsc_khz; > + do_div(cycles, 1000000); > + > + apic->lapic_timer.vmentry_advance_cycles = cycles; > + > + return cycles; > +} > + > +u64 get_vmentry_advance_cycles(struct kvm_vcpu *vcpu) > +{ > + struct kvm_lapic *apic = vcpu->arch.apic; > + > + if (unlikely(!vmentry_advance_ns)) > + return 0; > + > + if (likely(apic->lapic_timer.vmentry_advance_cycles)) > + return apic->lapic_timer.vmentry_advance_cycles; > + > + return compute_vmentry_advance_cycles(vcpu); If vmentry_advance_ns is read-only, then we don't need to be able to compute lapic_timer.vmentry_advance_cycles on demand, e.g. it can be set during kvm_create_lapic() and recomputed in kvm_set_tsc_khz(). Alternatively, it could be handled purely in kvm_set_tsc_khz() if the call to kvm_create_lapic() were moved before kvm_set_tsc_khz(). > +} > +EXPORT_SYMBOL_GPL(get_vmentry_advance_cycles); > + > void kvm_wait_lapic_expire(struct kvm_vcpu *vcpu) > { > struct kvm_lapic *apic = vcpu->arch.apic; > @@ -1544,7 +1571,7 @@ void kvm_wait_lapic_expire(struct kvm_vcpu *vcpu) > > tsc_deadline = apic->lapic_timer.expired_tscdeadline; > apic->lapic_timer.expired_tscdeadline = 0; > - guest_tsc = kvm_read_l1_tsc(vcpu, rdtsc()); > + guest_tsc = kvm_read_l1_tsc(vcpu, rdtsc()) + get_vmentry_advance_cycles(vcpu); > apic->lapic_timer.advance_expire_delta = guest_tsc - tsc_deadline; > > if (guest_tsc < tsc_deadline) > @@ -1572,7 +1599,7 @@ static void start_sw_tscdeadline(struct kvm_lapic *apic) > local_irq_save(flags); > > now = ktime_get(); > - guest_tsc = kvm_read_l1_tsc(vcpu, rdtsc()); > + guest_tsc = kvm_read_l1_tsc(vcpu, rdtsc()) + get_vmentry_advance_cycles(vcpu); > ns = (tscdeadline - guest_tsc) * 1000000ULL; > do_div(ns, this_tsc_khz); > @@ -2329,7 +2356,7 @@ int kvm_create_lapic(struct kvm_vcpu *vcpu, int timer_advance_ns) > apic->lapic_timer.timer_advance_ns = timer_advance_ns; > apic->lapic_timer.timer_advance_adjust_done = true; > } > - > + apic->lapic_timer.vmentry_advance_cycles = 0; > > /* > * APIC is created enabled. This will prevent kvm_lapic_set_base from > diff --git a/arch/x86/kvm/lapic.h b/arch/x86/kvm/lapic.h > index f974a3d..fb32e69 100644 > --- a/arch/x86/kvm/lapic.h > +++ b/arch/x86/kvm/lapic.h > @@ -33,6 +33,7 @@ struct kvm_timer { > u64 expired_tscdeadline; > u32 timer_advance_ns; > s64 advance_expire_delta; > + u64 vmentry_advance_cycles; > atomic_t pending; /* accumulated triggered timers */ > bool hv_timer_in_use; > bool timer_advance_adjust_done; > @@ -221,6 +222,8 @@ static inline int kvm_lapic_latched_init(struct kvm_vcpu *vcpu) > bool kvm_apic_pending_eoi(struct kvm_vcpu *vcpu, int vector); > > void kvm_wait_lapic_expire(struct kvm_vcpu *vcpu); > +u64 compute_vmentry_advance_cycles(struct kvm_vcpu *vcpu); > +u64 get_vmentry_advance_cycles(struct kvm_vcpu *vcpu); > > bool kvm_intr_is_single_vcpu_fast(struct kvm *kvm, struct kvm_lapic_irq *irq, > struct kvm_vcpu **dest_vcpu); > diff --git a/arch/x86/kvm/vmx/vmx.c b/arch/x86/kvm/vmx/vmx.c > index 0861c71..0751a44 100644 > --- a/arch/x86/kvm/vmx/vmx.c > +++ b/arch/x86/kvm/vmx/vmx.c > @@ -7041,7 +7041,7 @@ static int vmx_set_hv_timer(struct kvm_vcpu *vcpu, u64 guest_deadline_tsc, > > vmx = to_vmx(vcpu); > tscl = rdtsc(); > - guest_tscl = kvm_read_l1_tsc(vcpu, tscl); > + guest_tscl = kvm_read_l1_tsc(vcpu, tscl) + get_vmentry_advance_cycles(vcpu); > delta_tsc = max(guest_deadline_tsc, guest_tscl) - guest_tscl; > lapic_timer_advance_cycles = nsec_to_cycles(vcpu, > ktimer->timer_advance_ns); > diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c > index 553c292..4b983bb 100644 > --- a/arch/x86/kvm/x86.c > +++ b/arch/x86/kvm/x86.c > @@ -145,6 +145,12 @@ module_param(tsc_tolerance_ppm, uint, S_IRUGO | S_IWUSR); > static int __read_mostly lapic_timer_advance_ns = -1; > module_param(lapic_timer_advance_ns, int, S_IRUGO | S_IWUSR); > > +/* > + * lapic timer vmentry advance (tscdeadline mode only) in nanoseconds. > + */ > +u32 __read_mostly vmentry_advance_ns = 300; Enabling this by default makes me nervous, e.g. nothing guarantees that future versions of KVM and/or CPUs will continue to have 300ns of overhead between wait_lapic_expire() and VM-Enter. If we want it enabled by default so that it gets tested, the default value should be extremely conservative, e.g. set the default to a small percentage (25%?) of the latency of VM-Enter itself on modern CPUs, VM-Enter latency being the min between VMLAUNCH and VMLOAD+VMRUN+VMSAVE. > +module_param(vmentry_advance_ns, uint, S_IRUGO); > + > static bool __read_mostly vector_hashing = true; > module_param(vector_hashing, bool, S_IRUGO); > > @@ -1592,6 +1598,8 @@ static int kvm_set_tsc_khz(struct kvm_vcpu *vcpu, u32 user_tsc_khz) > kvm_get_time_scale(user_tsc_khz * 1000LL, NSEC_PER_SEC, > &vcpu->arch.virtual_tsc_shift, > &vcpu->arch.virtual_tsc_mult); > + if (vcpu->arch.apic && user_tsc_khz != vcpu->arch.virtual_tsc_khz) > + compute_vmentry_advance_cycles(vcpu); > vcpu->arch.virtual_tsc_khz = user_tsc_khz; > > /* > diff --git a/arch/x86/kvm/x86.h b/arch/x86/kvm/x86.h > index a470ff0..2174355 100644 > --- a/arch/x86/kvm/x86.h > +++ b/arch/x86/kvm/x86.h > @@ -294,6 +294,8 @@ extern u64 kvm_supported_xcr0(void); > > extern unsigned int min_timer_period_us; > > +extern unsigned int vmentry_advance_ns; > + > extern bool enable_vmware_backdoor; > > extern struct static_key kvm_no_apic_vcpu; > -- > 2.7.4 > ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v3 1/2] KVM: LAPIC: Optimize timer latency consider world switch time 2019-06-12 15:14 ` [PATCH v3 1/2] KVM: LAPIC: Optimize timer latency consider world switch time Sean Christopherson @ 2019-06-12 19:22 ` Radim Krčmář 2019-06-12 19:27 ` Radim Krčmář 2019-06-13 1:50 ` Wanpeng Li 1 sibling, 1 reply; 7+ messages in thread From: Radim Krčmář @ 2019-06-12 19:22 UTC (permalink / raw) To: Sean Christopherson; +Cc: Wanpeng Li, linux-kernel, kvm, Paolo Bonzini 2019-06-12 08:14-0700, Sean Christopherson: > On Wed, Jun 12, 2019 at 05:40:18PM +0800, Wanpeng Li wrote: > > diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c > > @@ -145,6 +145,12 @@ module_param(tsc_tolerance_ppm, uint, S_IRUGO | S_IWUSR); > > static int __read_mostly lapic_timer_advance_ns = -1; > > module_param(lapic_timer_advance_ns, int, S_IRUGO | S_IWUSR); > > > > +/* > > + * lapic timer vmentry advance (tscdeadline mode only) in nanoseconds. > > + */ > > +u32 __read_mostly vmentry_advance_ns = 300; > > Enabling this by default makes me nervous, e.g. nothing guarantees that > future versions of KVM and/or CPUs will continue to have 300ns of overhead > between wait_lapic_expire() and VM-Enter. > > If we want it enabled by default so that it gets tested, the default > value should be extremely conservative, e.g. set the default to a small > percentage (25%?) of the latency of VM-Enter itself on modern CPUs, > VM-Enter latency being the min between VMLAUNCH and VMLOAD+VMRUN+VMSAVE. I share the sentiment. We definitely must not enter the guest before the deadline has expired and CPUs are approaching 5 GHz (in turbo), so 300 ns would be too much even today. I wrote a simple testcase for rough timing and there are 267 cycles (111 ns @ 2.4 GHz) between doing rdtsc() right after kvm_wait_lapic_expire() [1] and doing rdtsc() in the guest as soon as possible (see the attached kvm-unit-test). That is on a Haswell, where vmexit.flat reports 2120 cycles for a vmcall. This would linearly (likely incorrect method in this case) translate to 230 cycles on a machine with 1800 cycles for a vmcall, which is less than 50 ns @ 5 GHz. I wouldn't go above 25 ns for a hard-coded default. (We could also do a similar measurement when initializing KVM and have a dynamic default, but I'm thinking it's going to be way too much code for the benefit.) --- 1: This is how the TSC is read in KVM. diff --git a/arch/x86/kvm/vmx/vmx.c b/arch/x86/kvm/vmx/vmx.c index da24f1858acc..a7251ac0109b 100644 --- a/arch/x86/kvm/vmx/vmx.c +++ b/arch/x86/kvm/vmx/vmx.c @@ -6449,6 +6449,8 @@ static void vmx_vcpu_run(struct kvm_vcpu *vcpu) vcpu->arch.apic->lapic_timer.timer_advance_ns) kvm_wait_lapic_expire(vcpu); + vcpu->last_seen_tsc = kvm_read_l1_tsc(vcpu, rdtsc()); + /* * If this vCPU has touched SPEC_CTRL, restore the guest's value if * it's non-zero. Since vmentry is serialising on affected CPUs, there diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c index 6200d5a51f13..5e0ce8ca31e7 100644 --- a/arch/x86/kvm/x86.c +++ b/arch/x86/kvm/x86.c @@ -7201,6 +7201,9 @@ int kvm_emulate_hypercall(struct kvm_vcpu *vcpu) case KVM_HC_SEND_IPI: ret = kvm_pv_send_ipi(vcpu->kvm, a0, a1, a2, a3, op_64_bit); break; + case KVM_HC_LAST_SEEN_TSC: + ret = vcpu->last_seen_tsc; + break; default: ret = -KVM_ENOSYS; break; diff --git a/include/linux/kvm_host.h b/include/linux/kvm_host.h index abafddb9fe2c..7f70fe7a28b1 100644 --- a/include/linux/kvm_host.h +++ b/include/linux/kvm_host.h @@ -323,6 +323,8 @@ struct kvm_vcpu { bool preempted; struct kvm_vcpu_arch arch; struct dentry *debugfs_dentry; + + u64 last_seen_tsc; }; static inline int kvm_vcpu_exiting_guest_mode(struct kvm_vcpu *vcpu) diff --git a/include/uapi/linux/kvm_para.h b/include/uapi/linux/kvm_para.h index 6c0ce49931e5..dfbc6e9ad7a1 100644 --- a/include/uapi/linux/kvm_para.h +++ b/include/uapi/linux/kvm_para.h @@ -28,6 +28,7 @@ #define KVM_HC_MIPS_CONSOLE_OUTPUT 8 #define KVM_HC_CLOCK_PAIRING 9 #define KVM_HC_SEND_IPI 10 +#define KVM_HC_LAST_SEEN_TSC 11 /* * hypercalls use architecture specific ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v3 1/2] KVM: LAPIC: Optimize timer latency consider world switch time 2019-06-12 19:22 ` Radim Krčmář @ 2019-06-12 19:27 ` Radim Krčmář 2019-06-13 1:52 ` Wanpeng Li 0 siblings, 1 reply; 7+ messages in thread From: Radim Krčmář @ 2019-06-12 19:27 UTC (permalink / raw) To: Sean Christopherson; +Cc: Wanpeng Li, linux-kernel, kvm, Paolo Bonzini 2019-06-12 21:22+0200, Radim Krčmář: > 2019-06-12 08:14-0700, Sean Christopherson: > > On Wed, Jun 12, 2019 at 05:40:18PM +0800, Wanpeng Li wrote: > > > diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c > > > @@ -145,6 +145,12 @@ module_param(tsc_tolerance_ppm, uint, S_IRUGO | S_IWUSR); > > > static int __read_mostly lapic_timer_advance_ns = -1; > > > module_param(lapic_timer_advance_ns, int, S_IRUGO | S_IWUSR); > > > > > > +/* > > > + * lapic timer vmentry advance (tscdeadline mode only) in nanoseconds. > > > + */ > > > +u32 __read_mostly vmentry_advance_ns = 300; > > > > Enabling this by default makes me nervous, e.g. nothing guarantees that > > future versions of KVM and/or CPUs will continue to have 300ns of overhead > > between wait_lapic_expire() and VM-Enter. > > > > If we want it enabled by default so that it gets tested, the default > > value should be extremely conservative, e.g. set the default to a small > > percentage (25%?) of the latency of VM-Enter itself on modern CPUs, > > VM-Enter latency being the min between VMLAUNCH and VMLOAD+VMRUN+VMSAVE. > > I share the sentiment. We definitely must not enter the guest before > the deadline has expired and CPUs are approaching 5 GHz (in turbo), so > 300 ns would be too much even today. > > I wrote a simple testcase for rough timing and there are 267 cycles > (111 ns @ 2.4 GHz) between doing rdtsc() right after > kvm_wait_lapic_expire() [1] and doing rdtsc() in the guest as soon as > possible (see the attached kvm-unit-test). I forgot to attach it, pasting here as a patch for kvm-unit-tests. --- diff --git a/x86/Makefile.common b/x86/Makefile.common index e612dbe..ceed648 100644 --- a/x86/Makefile.common +++ b/x86/Makefile.common @@ -58,7 +58,7 @@ tests-common = $(TEST_DIR)/vmexit.flat $(TEST_DIR)/tsc.flat \ $(TEST_DIR)/init.flat $(TEST_DIR)/smap.flat \ $(TEST_DIR)/hyperv_synic.flat $(TEST_DIR)/hyperv_stimer.flat \ $(TEST_DIR)/hyperv_connections.flat \ - $(TEST_DIR)/umip.flat + $(TEST_DIR)/umip.flat $(TEST_DIR)/vmentry_latency.flat ifdef API tests-api = api/api-sample api/dirty-log api/dirty-log-perf diff --git a/x86/vmentry_latency.c b/x86/vmentry_latency.c new file mode 100644 index 0000000..3859f09 --- /dev/null +++ b/x86/vmentry_latency.c @@ -0,0 +1,45 @@ +#include "x86/vm.h" + +static u64 get_last_hypervisor_tsc_delta(void) +{ + u64 a = 0, b, c, d; + u64 tsc; + + /* + * The first vmcall is there to force a vm exit just before measuring. + */ + asm volatile ("vmcall" : "+a"(a), "=b"(b), "=c"(c), "=d"(d)); + + tsc = rdtsc(); + + /* + * The second hypercall recovers the value that was stored when vm + * entering to execute the rdtsc() + */ + a = 11; + asm volatile ("vmcall" : "+a"(a), "=b"(b), "=c"(c), "=d"(d)); + + return tsc - a; +} + +static void vmentry_latency(void) +{ + unsigned i = 1000000; + u64 min = -1; + + while (i--) { + u64 latency = get_last_hypervisor_tsc_delta(); + if (latency < min) + min = latency; + } + + printf("vm entry latency is %"PRIu64" TSC cycles\n", min); +} + +int main(void) +{ + setup_vm(); + vmentry_latency(); + + return 0; +} ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v3 1/2] KVM: LAPIC: Optimize timer latency consider world switch time 2019-06-12 19:27 ` Radim Krčmář @ 2019-06-13 1:52 ` Wanpeng Li 0 siblings, 0 replies; 7+ messages in thread From: Wanpeng Li @ 2019-06-13 1:52 UTC (permalink / raw) To: Radim Krčmář; +Cc: Sean Christopherson, LKML, kvm, Paolo Bonzini On Thu, 13 Jun 2019 at 03:27, Radim Krčmář <rkrcmar@redhat.com> wrote: > > 2019-06-12 21:22+0200, Radim Krčmář: > > 2019-06-12 08:14-0700, Sean Christopherson: > > > On Wed, Jun 12, 2019 at 05:40:18PM +0800, Wanpeng Li wrote: > > > > diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c > > > > @@ -145,6 +145,12 @@ module_param(tsc_tolerance_ppm, uint, S_IRUGO | S_IWUSR); > > > > static int __read_mostly lapic_timer_advance_ns = -1; > > > > module_param(lapic_timer_advance_ns, int, S_IRUGO | S_IWUSR); > > > > > > > > +/* > > > > + * lapic timer vmentry advance (tscdeadline mode only) in nanoseconds. > > > > + */ > > > > +u32 __read_mostly vmentry_advance_ns = 300; > > > > > > Enabling this by default makes me nervous, e.g. nothing guarantees that > > > future versions of KVM and/or CPUs will continue to have 300ns of overhead > > > between wait_lapic_expire() and VM-Enter. > > > > > > If we want it enabled by default so that it gets tested, the default > > > value should be extremely conservative, e.g. set the default to a small > > > percentage (25%?) of the latency of VM-Enter itself on modern CPUs, > > > VM-Enter latency being the min between VMLAUNCH and VMLOAD+VMRUN+VMSAVE. > > > > I share the sentiment. We definitely must not enter the guest before > > the deadline has expired and CPUs are approaching 5 GHz (in turbo), so > > 300 ns would be too much even today. > > > > I wrote a simple testcase for rough timing and there are 267 cycles > > (111 ns @ 2.4 GHz) between doing rdtsc() right after > > kvm_wait_lapic_expire() [1] and doing rdtsc() in the guest as soon as > > possible (see the attached kvm-unit-test). > > I forgot to attach it, pasting here as a patch for kvm-unit-tests. Thanks for this, Radim. :) Regards, Wanpeng Li > > --- > diff --git a/x86/Makefile.common b/x86/Makefile.common > index e612dbe..ceed648 100644 > --- a/x86/Makefile.common > +++ b/x86/Makefile.common > @@ -58,7 +58,7 @@ tests-common = $(TEST_DIR)/vmexit.flat $(TEST_DIR)/tsc.flat \ > $(TEST_DIR)/init.flat $(TEST_DIR)/smap.flat \ > $(TEST_DIR)/hyperv_synic.flat $(TEST_DIR)/hyperv_stimer.flat \ > $(TEST_DIR)/hyperv_connections.flat \ > - $(TEST_DIR)/umip.flat > + $(TEST_DIR)/umip.flat $(TEST_DIR)/vmentry_latency.flat > > ifdef API > tests-api = api/api-sample api/dirty-log api/dirty-log-perf > diff --git a/x86/vmentry_latency.c b/x86/vmentry_latency.c > new file mode 100644 > index 0000000..3859f09 > --- /dev/null > +++ b/x86/vmentry_latency.c > @@ -0,0 +1,45 @@ > +#include "x86/vm.h" > + > +static u64 get_last_hypervisor_tsc_delta(void) > +{ > + u64 a = 0, b, c, d; > + u64 tsc; > + > + /* > + * The first vmcall is there to force a vm exit just before measuring. > + */ > + asm volatile ("vmcall" : "+a"(a), "=b"(b), "=c"(c), "=d"(d)); > + > + tsc = rdtsc(); > + > + /* > + * The second hypercall recovers the value that was stored when vm > + * entering to execute the rdtsc() > + */ > + a = 11; > + asm volatile ("vmcall" : "+a"(a), "=b"(b), "=c"(c), "=d"(d)); > + > + return tsc - a; > +} > + > +static void vmentry_latency(void) > +{ > + unsigned i = 1000000; > + u64 min = -1; > + > + while (i--) { > + u64 latency = get_last_hypervisor_tsc_delta(); > + if (latency < min) > + min = latency; > + } > + > + printf("vm entry latency is %"PRIu64" TSC cycles\n", min); > +} > + > +int main(void) > +{ > + setup_vm(); > + vmentry_latency(); > + > + return 0; > +} ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v3 1/2] KVM: LAPIC: Optimize timer latency consider world switch time 2019-06-12 15:14 ` [PATCH v3 1/2] KVM: LAPIC: Optimize timer latency consider world switch time Sean Christopherson 2019-06-12 19:22 ` Radim Krčmář @ 2019-06-13 1:50 ` Wanpeng Li 1 sibling, 0 replies; 7+ messages in thread From: Wanpeng Li @ 2019-06-13 1:50 UTC (permalink / raw) To: Sean Christopherson; +Cc: LKML, kvm, Paolo Bonzini, Radim Krčmář On Wed, 12 Jun 2019 at 23:14, Sean Christopherson <sean.j.christopherson@intel.com> wrote: > > On Wed, Jun 12, 2019 at 05:40:18PM +0800, Wanpeng Li wrote: > > From: Wanpeng Li <wanpengli@tencent.com> > > > > Advance lapic timer tries to hidden the hypervisor overhead between the > > host emulated timer fires and the guest awares the timer is fired. However, > > even though after more sustaining optimizations, kvm-unit-tests/tscdeadline_latency > > still awares ~1000 cycles latency since we lost the time between the end of > > wait_lapic_expire and the guest awares the timer is fired. There are > > codes between the end of wait_lapic_expire and the world switch, furthermore, > > the world switch itself also has overhead. Actually the guest_tsc is equal > > to the target deadline time in wait_lapic_expire is too late, guest will > > aware the latency between the end of wait_lapic_expire() and after vmentry > > to the guest. This patch takes this time into consideration. > > > > The vmentry+vmexit time which is measured by kvm-unit-tests/vmexit.falt is > > 1800 cycles on my 2.5GHz Skylake server, the vmentry_advance_ns module > > parameter default value is 300ns, it can be tuned/reworked in the further. > > This patch can reduce average cyclictest latency from 3us to 2us on Skylake > > server. (guest w/ nohz=off, idle=poll, host w/ preemption_timer=N, the > > cyclictest latency is not too sensitive when preemption_timer=Y for this > > optimization in my testing). > > > > Cc: Paolo Bonzini <pbonzini@redhat.com> > > Cc: Radim Krčmář <rkrcmar@redhat.com> > > Cc: Sean Christopherson <sean.j.christopherson@intel.com> > > Signed-off-by: Wanpeng Li <wanpengli@tencent.com> > > --- > > v2 -> v3: > > * read-only module parameter > > * get_vmentry_advance_cycles() not inline > > v1 -> v2: > > * rename get_vmentry_advance_delta to get_vmentry_advance_cycles > > * cache vmentry_advance_cycles by setting param bit 0 > > * add param max limit > > > > arch/x86/kvm/lapic.c | 33 ++++++++++++++++++++++++++++++--- > > arch/x86/kvm/lapic.h | 3 +++ > > arch/x86/kvm/vmx/vmx.c | 2 +- > > arch/x86/kvm/x86.c | 8 ++++++++ > > arch/x86/kvm/x86.h | 2 ++ > > 5 files changed, 44 insertions(+), 4 deletions(-) > > > > diff --git a/arch/x86/kvm/lapic.c b/arch/x86/kvm/lapic.c > > index fcf42a3..c6d76f9 100644 > > --- a/arch/x86/kvm/lapic.c > > +++ b/arch/x86/kvm/lapic.c > > @@ -1531,6 +1531,33 @@ static inline void adjust_lapic_timer_advance(struct kvm_vcpu *vcpu, > > apic->lapic_timer.timer_advance_ns = timer_advance_ns; > > } > > > > +u64 compute_vmentry_advance_cycles(struct kvm_vcpu *vcpu) > > +{ > > + u64 cycles; > > + struct kvm_lapic *apic = vcpu->arch.apic; > > + > > + cycles = vmentry_advance_ns * vcpu->arch.virtual_tsc_khz; > > + do_div(cycles, 1000000); > > + > > + apic->lapic_timer.vmentry_advance_cycles = cycles; > > + > > + return cycles; > > +} > > + > > +u64 get_vmentry_advance_cycles(struct kvm_vcpu *vcpu) > > +{ > > + struct kvm_lapic *apic = vcpu->arch.apic; > > + > > + if (unlikely(!vmentry_advance_ns)) > > + return 0; > > + > > + if (likely(apic->lapic_timer.vmentry_advance_cycles)) > > + return apic->lapic_timer.vmentry_advance_cycles; > > + > > + return compute_vmentry_advance_cycles(vcpu); > > If vmentry_advance_ns is read-only, then we don't need to be able to > compute lapic_timer.vmentry_advance_cycles on demand, e.g. it can be set > during kvm_create_lapic() and recomputed in kvm_set_tsc_khz(). > > Alternatively, it could be handled purely in kvm_set_tsc_khz() if the call > to kvm_create_lapic() were moved before kvm_set_tsc_khz(). hardcode 25ns, how about something like this: diff --git a/arch/x86/kvm/lapic.c b/arch/x86/kvm/lapic.c index fcf42a3..ed62d6b 100644 --- a/arch/x86/kvm/lapic.c +++ b/arch/x86/kvm/lapic.c @@ -1531,6 +1531,19 @@ static inline void adjust_lapic_timer_advance(struct kvm_vcpu *vcpu, apic->lapic_timer.timer_advance_ns = timer_advance_ns; } +u64 compute_vmentry_advance_cycles(struct kvm_vcpu *vcpu) +{ + u64 cycles; + struct kvm_lapic *apic = vcpu->arch.apic; + + cycles = vmentry_advance_ns * vcpu->arch.virtual_tsc_khz; + do_div(cycles, 1000000); + + apic->lapic_timer.vmentry_advance_cycles = cycles; + + return cycles; +} + void kvm_wait_lapic_expire(struct kvm_vcpu *vcpu) { struct kvm_lapic *apic = vcpu->arch.apic; @@ -1544,7 +1557,8 @@ void kvm_wait_lapic_expire(struct kvm_vcpu *vcpu) tsc_deadline = apic->lapic_timer.expired_tscdeadline; apic->lapic_timer.expired_tscdeadline = 0; - guest_tsc = kvm_read_l1_tsc(vcpu, rdtsc()); + guest_tsc = kvm_read_l1_tsc(vcpu, rdtsc()) + + apic->lapic_timer.vmentry_advance_cycles; apic->lapic_timer.advance_expire_delta = guest_tsc - tsc_deadline; if (guest_tsc < tsc_deadline) @@ -1572,7 +1586,8 @@ static void start_sw_tscdeadline(struct kvm_lapic *apic) local_irq_save(flags); now = ktime_get(); - guest_tsc = kvm_read_l1_tsc(vcpu, rdtsc()); + guest_tsc = kvm_read_l1_tsc(vcpu, rdtsc()) + + apic->lapic_timer.vmentry_advance_cycles; ns = (tscdeadline - guest_tsc) * 1000000ULL; do_div(ns, this_tsc_khz); @@ -2329,7 +2344,7 @@ int kvm_create_lapic(struct kvm_vcpu *vcpu, int timer_advance_ns) apic->lapic_timer.timer_advance_ns = timer_advance_ns; apic->lapic_timer.timer_advance_adjust_done = true; } - + apic->lapic_timer.vmentry_advance_cycles = 0; /* * APIC is created enabled. This will prevent kvm_lapic_set_base from diff --git a/arch/x86/kvm/lapic.h b/arch/x86/kvm/lapic.h index f974a3d..751cb26 100644 --- a/arch/x86/kvm/lapic.h +++ b/arch/x86/kvm/lapic.h @@ -33,6 +33,7 @@ struct kvm_timer { u64 expired_tscdeadline; u32 timer_advance_ns; s64 advance_expire_delta; + u64 vmentry_advance_cycles; atomic_t pending; /* accumulated triggered timers */ bool hv_timer_in_use; bool timer_advance_adjust_done; @@ -221,6 +222,7 @@ static inline int kvm_lapic_latched_init(struct kvm_vcpu *vcpu) bool kvm_apic_pending_eoi(struct kvm_vcpu *vcpu, int vector); void kvm_wait_lapic_expire(struct kvm_vcpu *vcpu); +u64 compute_vmentry_advance_cycles(struct kvm_vcpu *vcpu); bool kvm_intr_is_single_vcpu_fast(struct kvm *kvm, struct kvm_lapic_irq *irq, struct kvm_vcpu **dest_vcpu); diff --git a/arch/x86/kvm/vmx/vmx.c b/arch/x86/kvm/vmx/vmx.c index 0861c71..b572359 100644 --- a/arch/x86/kvm/vmx/vmx.c +++ b/arch/x86/kvm/vmx/vmx.c @@ -7041,7 +7041,8 @@ static int vmx_set_hv_timer(struct kvm_vcpu *vcpu, u64 guest_deadline_tsc, vmx = to_vmx(vcpu); tscl = rdtsc(); - guest_tscl = kvm_read_l1_tsc(vcpu, tscl); + guest_tscl = kvm_read_l1_tsc(vcpu, tscl) + + vcpu->arch.apic->lapic_timer.vmentry_advance_cycles; delta_tsc = max(guest_deadline_tsc, guest_tscl) - guest_tscl; lapic_timer_advance_cycles = nsec_to_cycles(vcpu, ktimer->timer_advance_ns); diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c index 553c292..f6e1366 100644 --- a/arch/x86/kvm/x86.c +++ b/arch/x86/kvm/x86.c @@ -145,6 +145,12 @@ module_param(tsc_tolerance_ppm, uint, S_IRUGO | S_IWUSR); static int __read_mostly lapic_timer_advance_ns = -1; module_param(lapic_timer_advance_ns, int, S_IRUGO | S_IWUSR); +/* + * lapic timer vmentry advance (tscdeadline mode only) in nanoseconds. + */ +u32 __read_mostly vmentry_advance_ns = 25; +module_param(vmentry_advance_ns, uint, S_IRUGO); + static bool __read_mostly vector_hashing = true; module_param(vector_hashing, bool, S_IRUGO); @@ -1592,6 +1598,8 @@ static int kvm_set_tsc_khz(struct kvm_vcpu *vcpu, u32 user_tsc_khz) kvm_get_time_scale(user_tsc_khz * 1000LL, NSEC_PER_SEC, &vcpu->arch.virtual_tsc_shift, &vcpu->arch.virtual_tsc_mult); + if (user_tsc_khz != vcpu->arch.virtual_tsc_khz) + compute_vmentry_advance_cycles(vcpu); vcpu->arch.virtual_tsc_khz = user_tsc_khz; /* @@ -9127,8 +9135,6 @@ int kvm_arch_vcpu_init(struct kvm_vcpu *vcpu) } vcpu->arch.pio_data = page_address(page); - kvm_set_tsc_khz(vcpu, max_tsc_khz); - r = kvm_mmu_create(vcpu); if (r < 0) goto fail_free_pio_data; @@ -9141,6 +9147,8 @@ int kvm_arch_vcpu_init(struct kvm_vcpu *vcpu) } else static_key_slow_inc(&kvm_no_apic_vcpu); + kvm_set_tsc_khz(vcpu, max_tsc_khz); + vcpu->arch.mce_banks = kzalloc(KVM_MAX_MCE_BANKS * sizeof(u64) * 4, GFP_KERNEL_ACCOUNT); if (!vcpu->arch.mce_banks) { diff --git a/arch/x86/kvm/x86.h b/arch/x86/kvm/x86.h index a470ff0..2174355 100644 --- a/arch/x86/kvm/x86.h +++ b/arch/x86/kvm/x86.h @@ -294,6 +294,8 @@ extern u64 kvm_supported_xcr0(void); extern unsigned int min_timer_period_us; +extern unsigned int vmentry_advance_ns; + extern bool enable_vmware_backdoor; extern struct static_key kvm_no_apic_vcpu; ^ permalink raw reply related [flat|nested] 7+ messages in thread
end of thread, other threads:[~2019-06-13 16:56 UTC | newest] Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2019-06-12 9:40 [PATCH v3 1/2] KVM: LAPIC: Optimize timer latency consider world switch time Wanpeng Li 2019-06-12 9:40 ` [PATCH v3 2/2] KVM: LAPIC: remove the trailing newline used in the fmt parameter of TP_printk Wanpeng Li 2019-06-12 15:14 ` [PATCH v3 1/2] KVM: LAPIC: Optimize timer latency consider world switch time Sean Christopherson 2019-06-12 19:22 ` Radim Krčmář 2019-06-12 19:27 ` Radim Krčmář 2019-06-13 1:52 ` Wanpeng Li 2019-06-13 1:50 ` Wanpeng Li
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).