[PATCH AUTOSEL 4.20 04/81] arm: dts: meson: Fix IRQ trigger type for macirq

[PATCH AUTOSEL 4.20 04/81] arm: dts: meson: Fix IRQ trigger type for macirq

[Sasha Levin]

From: Carlo Caione <ccaione@baylibre.com>

[ Upstream commit e35e26b26e955c53e61c154ba26b9bb15da6b858 ]

A long running stress test on a custom board shipping an AXG SoCs and a
Realtek RTL8211F PHY revealed that after a few hours the connection
speed would drop drastically, from ~1000Mbps to ~3Mbps. At the same time
the 'macirq' (eth0) IRQ would stop being triggered at all and as
consequence the GMAC IRQs never ACKed.

After a painful investigation the problem seemed to be due to a wrong
defined IRQ type for the GMAC IRQ that should be LEVEL_HIGH instead of
EDGE_RISING.

The change in the macirq IRQ type also solved another long standing
issue affecting this SoC/PHY where EEE was causing the network
connection to die after stressing it with iperf3 (even though much
sooner). It's now possible to remove the 'eee-broken-1000t' quirk as
well.

Fixes: 9c15795a4f96 ("ARM: dts: meson8b-odroidc1: ethernet support")
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/meson.dtsi           | 2 +-
 arch/arm/boot/dts/meson8b-odroidc1.dts | 1 -
 2 files changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/meson.dtsi b/arch/arm/boot/dts/meson.dtsi
index 0d9faf1a51eac..a86b890863347 100644
--- a/arch/arm/boot/dts/meson.dtsi
+++ b/arch/arm/boot/dts/meson.dtsi
@@ -263,7 +263,7 @@
 			compatible = "amlogic,meson6-dwmac", "snps,dwmac";
 			reg = <0xc9410000 0x10000
 			       0xc1108108 0x4>;
-			interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 			status = "disabled";
 		};
diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
index 58669abda2594..a951a6632d0c7 100644
--- a/arch/arm/boot/dts/meson8b-odroidc1.dts
+++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
@@ -221,7 +221,6 @@
 		/* Realtek RTL8211F (0x001cc916) */
 		eth_phy: ethernet-phy@0 {
 			reg = <0>;
-			eee-broken-1000t;
 			interrupt-parent = <&gpio_intc>;
 			/* GPIOH_3 */
 			interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
-- 
2.19.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH AUTOSEL 4.20 05/81] ARM: dts: meson8b: odroidc1: mark the SD card detection GPIO active-low

[Sasha Levin]

From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

[ Upstream commit 3fb348e030319f20ebbde082a449d4bf8a96f2fd ]

After commit 89a5e15bcba87d ("gpio/mmc/of: Respect polarity in the device
tree") SD cards are not detected anymore.

The CD GPIO is "active low" on Odroid-C1. The MMC dt-bindings specify:
"[...] using the "cd-inverted" property means, that the CD line is active
high, i.e. it is high, when a card is inserted".

Fix the description of the SD card by marking it as GPIO_ACTIVE_LOW and
drop the "cd-inverted" property. This makes the definition consistent
with the existing dt-bindings and fixes the check whether an SD card is
inserted.

Fixes: e03efbce6bebf5 ("ARM: dts: meson8b-odroidc1: add microSD support")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/meson8b-odroidc1.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
index a951a6632d0c7..0f0a46ddf3ff2 100644
--- a/arch/arm/boot/dts/meson8b-odroidc1.dts
+++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
@@ -272,8 +272,7 @@
 		cap-sd-highspeed;
 		disable-wp;
 
-		cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-		cd-inverted;
+		cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 		vmmc-supply = <&tflash_vdd>;
 		vqmmc-supply = <&tf_io>;
-- 
2.19.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH AUTOSEL 4.20 06/81] ARM: dts: meson8b: ec100: mark the SD card detection GPIO active-low

[Sasha Levin]

From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

[ Upstream commit c8bfe65fb1fb7a43d766df1dfa379406112cba61 ]

After commit 89a5e15bcba87d ("gpio/mmc/of: Respect polarity in the device
tree") SD cards are not detected anymore.

The CD GPIO is "active low" on the EC-100. The MMC dt-bindings specify:
"[...] using the "cd-inverted" property means, that the CD line is active
high, i.e. it is high, when a card is inserted".

Fix the description of the SD card by marking it as GPIO_ACTIVE_LOW and
drop the "cd-inverted" property. This makes the definition consistent
with the existing dt-bindings and fixes the check whether an SD card is
inserted.

Fixes: bbedc1f1d90e33 ("ARM: dts: meson8b: Add support for the Endless Mini (EC-100)")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/meson8b-ec100.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/meson8b-ec100.dts b/arch/arm/boot/dts/meson8b-ec100.dts
index 0872f6e3abf56..d50fc2f60fa31 100644
--- a/arch/arm/boot/dts/meson8b-ec100.dts
+++ b/arch/arm/boot/dts/meson8b-ec100.dts
@@ -205,8 +205,7 @@
 		cap-sd-highspeed;
 		disable-wp;
 
-		cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-		cd-inverted;
+		cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 		vmmc-supply = <&vcc_3v3>;
 	};
-- 
2.19.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH AUTOSEL 4.20 07/81] ARM: dts: meson8m2: mxiii-plus: mark the SD card detection GPIO active-low

[Sasha Levin]

From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

[ Upstream commit 8615f5596335db0978cea593dcd0070dc5f8b116 ]

After commit 89a5e15bcba87d ("gpio/mmc/of: Respect polarity in the device
tree") SD cards are not detected anymore.

The CD GPIO is "active low" on the MXIII-Plus. The MMC dt-bindings
specify: "[...] using the "cd-inverted" property means, that the CD line
is active high, i.e. it is high, when a card is inserted".

Fix the description of the SD card by marking it as GPIO_ACTIVE_LOW and
drop the "cd-inverted" property. This makes the definition consistent
with the existing dt-bindings and fixes the check whether an SD card is
inserted.

Fixes: 35ee52bea66c74 ("ARM: dts: meson8m2: add support for the Tronsmart MXIII Plus")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/meson8m2-mxiii-plus.dts | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts b/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
index f5853610b20b8..6ac02beb5fa72 100644
--- a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
+++ b/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
@@ -206,8 +206,7 @@
 		cap-sd-highspeed;
 		disable-wp;
 
-		cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
-		cd-inverted;
+		cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
 
 		vmmc-supply = <&vcc_3v3>;
 	};
-- 
2.19.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic