linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
* [PATCH V4] clk: imx: Fix reparenting of UARTs not associated with stdout
@ 2021-03-13 12:28 Adam Ford
  2021-03-13 15:16 ` Ahmad Fatoum
  2021-03-22 21:42 ` Abel Vesa
  0 siblings, 2 replies; 7+ messages in thread
From: Adam Ford @ 2021-03-13 12:28 UTC (permalink / raw)
  To: linux-clk
  Cc: aford, Adam Ford, Aisheng Dong, Abel Vesa, Ahmad Fatoum,
	Michael Turquette, Stephen Boyd, Shawn Guo, Sascha Hauer,
	Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
	Jerome Brunet, Linus Walleij, linux-arm-kernel, linux-kernel

Most if not all i.MX SoC's call a function which enables all UARTS.
This is a problem for users who need to re-parent the clock source,
because any attempt to change the parent results in an busy error
due to the fact that the clocks have been enabled already.

  clk: failed to reparent uart1 to sys_pll1_80m: -16

Instead of pre-initializing all UARTS, scan the device tree to see
which UART clocks are associated to stdout, and only enable those
UART clocks if it's needed early.  This will move initialization of
the remaining clocks until after the parenting of the clocks.

When the clocks are shutdown, this mechanism will also disable any
clocks that were pre-initialized.

Fixes: 9461f7b33d11c ("clk: fix CLK_SET_RATE_GATE with clock rate protection")
Suggested-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>

---
V4:  Check if of_stdout is available before using it.
     Re-align #ifdef to remove repeated code.
V3:  Return a method more closely related to upstream kernel but
     instead of passing an array of UART's, each SoC passes the max
     number of UART clocks is has.  The imx clock driver will create
     an array to enable on startup, and disable later.
V2:  Attempt to port driver from vendor kernel.
---
 drivers/clk/imx/clk-imx25.c   | 12 +---------
 drivers/clk/imx/clk-imx27.c   | 13 +----------
 drivers/clk/imx/clk-imx35.c   | 10 +--------
 drivers/clk/imx/clk-imx5.c    | 30 +++----------------------
 drivers/clk/imx/clk-imx6q.c   | 16 +-------------
 drivers/clk/imx/clk-imx6sl.c  | 16 +-------------
 drivers/clk/imx/clk-imx6sll.c | 24 +-------------------
 drivers/clk/imx/clk-imx6sx.c  | 16 +-------------
 drivers/clk/imx/clk-imx7d.c   | 22 +------------------
 drivers/clk/imx/clk-imx7ulp.c | 31 ++------------------------
 drivers/clk/imx/clk-imx8mm.c  | 18 ++-------------
 drivers/clk/imx/clk-imx8mn.c  | 18 ++-------------
 drivers/clk/imx/clk-imx8mp.c  | 17 +--------------
 drivers/clk/imx/clk-imx8mq.c  | 18 ++-------------
 drivers/clk/imx/clk.c         | 41 +++++++++++++++++++++++++++--------
 drivers/clk/imx/clk.h         |  4 ++--
 16 files changed, 54 insertions(+), 252 deletions(-)

diff --git a/drivers/clk/imx/clk-imx25.c b/drivers/clk/imx/clk-imx25.c
index a66cabfbf94f..66192fe0a898 100644
--- a/drivers/clk/imx/clk-imx25.c
+++ b/drivers/clk/imx/clk-imx25.c
@@ -73,16 +73,6 @@ enum mx25_clks {
 
 static struct clk *clk[clk_max];
 
-static struct clk ** const uart_clks[] __initconst = {
-	&clk[uart_ipg_per],
-	&clk[uart1_ipg],
-	&clk[uart2_ipg],
-	&clk[uart3_ipg],
-	&clk[uart4_ipg],
-	&clk[uart5_ipg],
-	NULL
-};
-
 static int __init __mx25_clocks_init(void __iomem *ccm_base)
 {
 	BUG_ON(!ccm_base);
@@ -228,7 +218,7 @@ static int __init __mx25_clocks_init(void __iomem *ccm_base)
 	 */
 	clk_set_parent(clk[cko_sel], clk[ipg]);
 
-	imx_register_uart_clocks(uart_clks);
+	imx_register_uart_clocks(6);
 
 	return 0;
 }
diff --git a/drivers/clk/imx/clk-imx27.c b/drivers/clk/imx/clk-imx27.c
index 5585ded8b8c6..56a5fc402b10 100644
--- a/drivers/clk/imx/clk-imx27.c
+++ b/drivers/clk/imx/clk-imx27.c
@@ -49,17 +49,6 @@ static const char *ssi_sel_clks[] = { "spll_gate", "mpll", };
 static struct clk *clk[IMX27_CLK_MAX];
 static struct clk_onecell_data clk_data;
 
-static struct clk ** const uart_clks[] __initconst = {
-	&clk[IMX27_CLK_PER1_GATE],
-	&clk[IMX27_CLK_UART1_IPG_GATE],
-	&clk[IMX27_CLK_UART2_IPG_GATE],
-	&clk[IMX27_CLK_UART3_IPG_GATE],
-	&clk[IMX27_CLK_UART4_IPG_GATE],
-	&clk[IMX27_CLK_UART5_IPG_GATE],
-	&clk[IMX27_CLK_UART6_IPG_GATE],
-	NULL
-};
-
 static void __init _mx27_clocks_init(unsigned long fref)
 {
 	BUG_ON(!ccm);
@@ -176,7 +165,7 @@ static void __init _mx27_clocks_init(unsigned long fref)
 
 	clk_prepare_enable(clk[IMX27_CLK_EMI_AHB_GATE]);
 
-	imx_register_uart_clocks(uart_clks);
+	imx_register_uart_clocks(7);
 
 	imx_print_silicon_rev("i.MX27", mx27_revision());
 }
diff --git a/drivers/clk/imx/clk-imx35.c b/drivers/clk/imx/clk-imx35.c
index c1df03665c09..0fe5ac210156 100644
--- a/drivers/clk/imx/clk-imx35.c
+++ b/drivers/clk/imx/clk-imx35.c
@@ -82,14 +82,6 @@ enum mx35_clks {
 
 static struct clk *clk[clk_max];
 
-static struct clk ** const uart_clks[] __initconst = {
-	&clk[ipg],
-	&clk[uart1_gate],
-	&clk[uart2_gate],
-	&clk[uart3_gate],
-	NULL
-};
-
 static void __init _mx35_clocks_init(void)
 {
 	void __iomem *base;
@@ -243,7 +235,7 @@ static void __init _mx35_clocks_init(void)
 	 */
 	clk_prepare_enable(clk[scc_gate]);
 
-	imx_register_uart_clocks(uart_clks);
+	imx_register_uart_clocks(4);
 
 	imx_print_silicon_rev("i.MX35", mx35_revision());
 }
diff --git a/drivers/clk/imx/clk-imx5.c b/drivers/clk/imx/clk-imx5.c
index 01e079b81026..e4493846454d 100644
--- a/drivers/clk/imx/clk-imx5.c
+++ b/drivers/clk/imx/clk-imx5.c
@@ -128,30 +128,6 @@ static const char *ieee1588_sels[] = { "pll3_sw", "pll4_sw", "dummy" /* usbphy2_
 static struct clk *clk[IMX5_CLK_END];
 static struct clk_onecell_data clk_data;
 
-static struct clk ** const uart_clks_mx51[] __initconst = {
-	&clk[IMX5_CLK_UART1_IPG_GATE],
-	&clk[IMX5_CLK_UART1_PER_GATE],
-	&clk[IMX5_CLK_UART2_IPG_GATE],
-	&clk[IMX5_CLK_UART2_PER_GATE],
-	&clk[IMX5_CLK_UART3_IPG_GATE],
-	&clk[IMX5_CLK_UART3_PER_GATE],
-	NULL
-};
-
-static struct clk ** const uart_clks_mx50_mx53[] __initconst = {
-	&clk[IMX5_CLK_UART1_IPG_GATE],
-	&clk[IMX5_CLK_UART1_PER_GATE],
-	&clk[IMX5_CLK_UART2_IPG_GATE],
-	&clk[IMX5_CLK_UART2_PER_GATE],
-	&clk[IMX5_CLK_UART3_IPG_GATE],
-	&clk[IMX5_CLK_UART3_PER_GATE],
-	&clk[IMX5_CLK_UART4_IPG_GATE],
-	&clk[IMX5_CLK_UART4_PER_GATE],
-	&clk[IMX5_CLK_UART5_IPG_GATE],
-	&clk[IMX5_CLK_UART5_PER_GATE],
-	NULL
-};
-
 static void __init mx5_clocks_common_init(void __iomem *ccm_base)
 {
 	clk[IMX5_CLK_DUMMY]		= imx_clk_fixed("dummy", 0);
@@ -382,7 +358,7 @@ static void __init mx50_clocks_init(struct device_node *np)
 	r = clk_round_rate(clk[IMX5_CLK_USBOH3_PER_GATE], 54000000);
 	clk_set_rate(clk[IMX5_CLK_USBOH3_PER_GATE], r);
 
-	imx_register_uart_clocks(uart_clks_mx50_mx53);
+	imx_register_uart_clocks(5);
 }
 CLK_OF_DECLARE(imx50_ccm, "fsl,imx50-ccm", mx50_clocks_init);
 
@@ -488,7 +464,7 @@ static void __init mx51_clocks_init(struct device_node *np)
 	val |= 1 << 23;
 	writel(val, MXC_CCM_CLPCR);
 
-	imx_register_uart_clocks(uart_clks_mx51);
+	imx_register_uart_clocks(3);
 }
 CLK_OF_DECLARE(imx51_ccm, "fsl,imx51-ccm", mx51_clocks_init);
 
@@ -633,6 +609,6 @@ static void __init mx53_clocks_init(struct device_node *np)
 	r = clk_round_rate(clk[IMX5_CLK_USBOH3_PER_GATE], 54000000);
 	clk_set_rate(clk[IMX5_CLK_USBOH3_PER_GATE], r);
 
-	imx_register_uart_clocks(uart_clks_mx50_mx53);
+	imx_register_uart_clocks(5);
 }
 CLK_OF_DECLARE(imx53_ccm, "fsl,imx53-ccm", mx53_clocks_init);
diff --git a/drivers/clk/imx/clk-imx6q.c b/drivers/clk/imx/clk-imx6q.c
index 521d6136d22c..496900de0b0b 100644
--- a/drivers/clk/imx/clk-imx6q.c
+++ b/drivers/clk/imx/clk-imx6q.c
@@ -140,13 +140,6 @@ static inline int clk_on_imx6dl(void)
 	return of_machine_is_compatible("fsl,imx6dl");
 }
 
-static const int uart_clk_ids[] __initconst = {
-	IMX6QDL_CLK_UART_IPG,
-	IMX6QDL_CLK_UART_SERIAL,
-};
-
-static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
-
 static int ldb_di_sel_by_clock_id(int clock_id)
 {
 	switch (clock_id) {
@@ -440,7 +433,6 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
 	struct device_node *np;
 	void __iomem *anatop_base, *base;
 	int ret;
-	int i;
 
 	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
 					  IMX6QDL_CLK_END), GFP_KERNEL);
@@ -982,12 +974,6 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
 			       hws[IMX6QDL_CLK_PLL3_USB_OTG]->clk);
 	}
 
-	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
-		int index = uart_clk_ids[i];
-
-		uart_clks[i] = &hws[index]->clk;
-	}
-
-	imx_register_uart_clocks(uart_clks);
+	imx_register_uart_clocks(1);
 }
 CLK_OF_DECLARE(imx6q, "fsl,imx6q-ccm", imx6q_clocks_init);
diff --git a/drivers/clk/imx/clk-imx6sl.c b/drivers/clk/imx/clk-imx6sl.c
index 29eab05c9068..277365970320 100644
--- a/drivers/clk/imx/clk-imx6sl.c
+++ b/drivers/clk/imx/clk-imx6sl.c
@@ -179,19 +179,11 @@ void imx6sl_set_wait_clk(bool enter)
 		imx6sl_enable_pll_arm(false);
 }
 
-static const int uart_clk_ids[] __initconst = {
-	IMX6SL_CLK_UART,
-	IMX6SL_CLK_UART_SERIAL,
-};
-
-static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
-
 static void __init imx6sl_clocks_init(struct device_node *ccm_node)
 {
 	struct device_node *np;
 	void __iomem *base;
 	int ret;
-	int i;
 
 	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
 					  IMX6SL_CLK_END), GFP_KERNEL);
@@ -448,12 +440,6 @@ static void __init imx6sl_clocks_init(struct device_node *ccm_node)
 	clk_set_parent(hws[IMX6SL_CLK_LCDIF_AXI_SEL]->clk,
 		       hws[IMX6SL_CLK_PLL2_PFD2]->clk);
 
-	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
-		int index = uart_clk_ids[i];
-
-		uart_clks[i] = &hws[index]->clk;
-	}
-
-	imx_register_uart_clocks(uart_clks);
+	imx_register_uart_clocks(2);
 }
 CLK_OF_DECLARE(imx6sl, "fsl,imx6sl-ccm", imx6sl_clocks_init);
diff --git a/drivers/clk/imx/clk-imx6sll.c b/drivers/clk/imx/clk-imx6sll.c
index 8e8288bda4d0..31d777f30039 100644
--- a/drivers/clk/imx/clk-imx6sll.c
+++ b/drivers/clk/imx/clk-imx6sll.c
@@ -76,26 +76,10 @@ static u32 share_count_ssi1;
 static u32 share_count_ssi2;
 static u32 share_count_ssi3;
 
-static const int uart_clk_ids[] __initconst = {
-	IMX6SLL_CLK_UART1_IPG,
-	IMX6SLL_CLK_UART1_SERIAL,
-	IMX6SLL_CLK_UART2_IPG,
-	IMX6SLL_CLK_UART2_SERIAL,
-	IMX6SLL_CLK_UART3_IPG,
-	IMX6SLL_CLK_UART3_SERIAL,
-	IMX6SLL_CLK_UART4_IPG,
-	IMX6SLL_CLK_UART4_SERIAL,
-	IMX6SLL_CLK_UART5_IPG,
-	IMX6SLL_CLK_UART5_SERIAL,
-};
-
-static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
-
 static void __init imx6sll_clocks_init(struct device_node *ccm_node)
 {
 	struct device_node *np;
 	void __iomem *base;
-	int i;
 
 	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
 					  IMX6SLL_CLK_END), GFP_KERNEL);
@@ -356,13 +340,7 @@ static void __init imx6sll_clocks_init(struct device_node *ccm_node)
 
 	of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_hw_data);
 
-	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
-		int index = uart_clk_ids[i];
-
-		uart_clks[i] = &hws[index]->clk;
-	}
-
-	imx_register_uart_clocks(uart_clks);
+	imx_register_uart_clocks(5);
 
 	/* Lower the AHB clock rate before changing the clock source. */
 	clk_set_rate(hws[IMX6SLL_CLK_AHB]->clk, 99000000);
diff --git a/drivers/clk/imx/clk-imx6sx.c b/drivers/clk/imx/clk-imx6sx.c
index 20dcce526d07..fc1bd23d4583 100644
--- a/drivers/clk/imx/clk-imx6sx.c
+++ b/drivers/clk/imx/clk-imx6sx.c
@@ -117,18 +117,10 @@ static u32 share_count_ssi3;
 static u32 share_count_sai1;
 static u32 share_count_sai2;
 
-static const int uart_clk_ids[] __initconst = {
-	IMX6SX_CLK_UART_IPG,
-	IMX6SX_CLK_UART_SERIAL,
-};
-
-static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
-
 static void __init imx6sx_clocks_init(struct device_node *ccm_node)
 {
 	struct device_node *np;
 	void __iomem *base;
-	int i;
 
 	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
 					  IMX6SX_CLK_CLK_END), GFP_KERNEL);
@@ -556,12 +548,6 @@ static void __init imx6sx_clocks_init(struct device_node *ccm_node)
 	clk_set_parent(hws[IMX6SX_CLK_QSPI1_SEL]->clk, hws[IMX6SX_CLK_PLL2_BUS]->clk);
 	clk_set_parent(hws[IMX6SX_CLK_QSPI2_SEL]->clk, hws[IMX6SX_CLK_PLL2_BUS]->clk);
 
-	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
-		int index = uart_clk_ids[i];
-
-		uart_clks[i] = &hws[index]->clk;
-	}
-
-	imx_register_uart_clocks(uart_clks);
+	imx_register_uart_clocks(2);
 }
 CLK_OF_DECLARE(imx6sx, "fsl,imx6sx-ccm", imx6sx_clocks_init);
diff --git a/drivers/clk/imx/clk-imx7d.c b/drivers/clk/imx/clk-imx7d.c
index 22d24a6a05e7..c4e0f1c07192 100644
--- a/drivers/clk/imx/clk-imx7d.c
+++ b/drivers/clk/imx/clk-imx7d.c
@@ -377,23 +377,10 @@ static const char *pll_video_bypass_sel[] = { "pll_video_main", "pll_video_main_
 static struct clk_hw **hws;
 static struct clk_hw_onecell_data *clk_hw_data;
 
-static const int uart_clk_ids[] __initconst = {
-	IMX7D_UART1_ROOT_CLK,
-	IMX7D_UART2_ROOT_CLK,
-	IMX7D_UART3_ROOT_CLK,
-	IMX7D_UART4_ROOT_CLK,
-	IMX7D_UART5_ROOT_CLK,
-	IMX7D_UART6_ROOT_CLK,
-	IMX7D_UART7_ROOT_CLK,
-};
-
-static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
-
 static void __init imx7d_clocks_init(struct device_node *ccm_node)
 {
 	struct device_node *np;
 	void __iomem *base;
-	int i;
 
 	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
 					  IMX7D_CLK_END), GFP_KERNEL);
@@ -897,14 +884,7 @@ static void __init imx7d_clocks_init(struct device_node *ccm_node)
 	hws[IMX7D_USB1_MAIN_480M_CLK] = imx_clk_hw_fixed_factor("pll_usb1_main_clk", "osc", 20, 1);
 	hws[IMX7D_USB_MAIN_480M_CLK] = imx_clk_hw_fixed_factor("pll_usb_main_clk", "osc", 20, 1);
 
-	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
-		int index = uart_clk_ids[i];
-
-		uart_clks[i] = &hws[index]->clk;
-	}
-
-
-	imx_register_uart_clocks(uart_clks);
+	imx_register_uart_clocks(7);
 
 }
 CLK_OF_DECLARE(imx7d, "fsl,imx7d-ccm", imx7d_clocks_init);
diff --git a/drivers/clk/imx/clk-imx7ulp.c b/drivers/clk/imx/clk-imx7ulp.c
index 634c0b6636b0..779e09105da7 100644
--- a/drivers/clk/imx/clk-imx7ulp.c
+++ b/drivers/clk/imx/clk-imx7ulp.c
@@ -43,19 +43,6 @@ static const struct clk_div_table ulp_div_table[] = {
 	{ /* sentinel */ },
 };
 
-static const int pcc2_uart_clk_ids[] __initconst = {
-	IMX7ULP_CLK_LPUART4,
-	IMX7ULP_CLK_LPUART5,
-};
-
-static const int pcc3_uart_clk_ids[] __initconst = {
-	IMX7ULP_CLK_LPUART6,
-	IMX7ULP_CLK_LPUART7,
-};
-
-static struct clk **pcc2_uart_clks[ARRAY_SIZE(pcc2_uart_clk_ids) + 1] __initdata;
-static struct clk **pcc3_uart_clks[ARRAY_SIZE(pcc3_uart_clk_ids) + 1] __initdata;
-
 static void __init imx7ulp_clk_scg1_init(struct device_node *np)
 {
 	struct clk_hw_onecell_data *clk_data;
@@ -150,7 +137,6 @@ static void __init imx7ulp_clk_pcc2_init(struct device_node *np)
 	struct clk_hw_onecell_data *clk_data;
 	struct clk_hw **hws;
 	void __iomem *base;
-	int i;
 
 	clk_data = kzalloc(struct_size(clk_data, hws, IMX7ULP_CLK_PCC2_END),
 			   GFP_KERNEL);
@@ -190,13 +176,7 @@ static void __init imx7ulp_clk_pcc2_init(struct device_node *np)
 
 	of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_data);
 
-	for (i = 0; i < ARRAY_SIZE(pcc2_uart_clk_ids); i++) {
-		int index = pcc2_uart_clk_ids[i];
-
-		pcc2_uart_clks[i] = &hws[index]->clk;
-	}
-
-	imx_register_uart_clocks(pcc2_uart_clks);
+	imx_register_uart_clocks(2);
 }
 CLK_OF_DECLARE(imx7ulp_clk_pcc2, "fsl,imx7ulp-pcc2", imx7ulp_clk_pcc2_init);
 
@@ -205,7 +185,6 @@ static void __init imx7ulp_clk_pcc3_init(struct device_node *np)
 	struct clk_hw_onecell_data *clk_data;
 	struct clk_hw **hws;
 	void __iomem *base;
-	int i;
 
 	clk_data = kzalloc(struct_size(clk_data, hws, IMX7ULP_CLK_PCC3_END),
 			   GFP_KERNEL);
@@ -244,13 +223,7 @@ static void __init imx7ulp_clk_pcc3_init(struct device_node *np)
 
 	of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_data);
 
-	for (i = 0; i < ARRAY_SIZE(pcc3_uart_clk_ids); i++) {
-		int index = pcc3_uart_clk_ids[i];
-
-		pcc3_uart_clks[i] = &hws[index]->clk;
-	}
-
-	imx_register_uart_clocks(pcc3_uart_clks);
+	imx_register_uart_clocks(7);
 }
 CLK_OF_DECLARE(imx7ulp_clk_pcc3, "fsl,imx7ulp-pcc3", imx7ulp_clk_pcc3_init);
 
diff --git a/drivers/clk/imx/clk-imx8mm.c b/drivers/clk/imx/clk-imx8mm.c
index 6a01eec36dd0..f1919fafb124 100644
--- a/drivers/clk/imx/clk-imx8mm.c
+++ b/drivers/clk/imx/clk-imx8mm.c
@@ -296,20 +296,12 @@ static const char * const clkout_sels[] = {"audio_pll1_out", "audio_pll2_out", "
 static struct clk_hw_onecell_data *clk_hw_data;
 static struct clk_hw **hws;
 
-static const int uart_clk_ids[] = {
-	IMX8MM_CLK_UART1_ROOT,
-	IMX8MM_CLK_UART2_ROOT,
-	IMX8MM_CLK_UART3_ROOT,
-	IMX8MM_CLK_UART4_ROOT,
-};
-static struct clk **uart_hws[ARRAY_SIZE(uart_clk_ids) + 1];
-
 static int imx8mm_clocks_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct device_node *np = dev->of_node;
 	void __iomem *base;
-	int ret, i;
+	int ret;
 
 	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
 					  IMX8MM_CLK_END), GFP_KERNEL);
@@ -634,13 +626,7 @@ static int imx8mm_clocks_probe(struct platform_device *pdev)
 		goto unregister_hws;
 	}
 
-	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
-		int index = uart_clk_ids[i];
-
-		uart_hws[i] = &hws[index]->clk;
-	}
-
-	imx_register_uart_clocks(uart_hws);
+	imx_register_uart_clocks(4);
 
 	return 0;
 
diff --git a/drivers/clk/imx/clk-imx8mn.c b/drivers/clk/imx/clk-imx8mn.c
index 324c5fd0aa04..88f6630cd472 100644
--- a/drivers/clk/imx/clk-imx8mn.c
+++ b/drivers/clk/imx/clk-imx8mn.c
@@ -289,20 +289,12 @@ static const char * const clkout_sels[] = {"audio_pll1_out", "audio_pll2_out", "
 static struct clk_hw_onecell_data *clk_hw_data;
 static struct clk_hw **hws;
 
-static const int uart_clk_ids[] = {
-	IMX8MN_CLK_UART1_ROOT,
-	IMX8MN_CLK_UART2_ROOT,
-	IMX8MN_CLK_UART3_ROOT,
-	IMX8MN_CLK_UART4_ROOT,
-};
-static struct clk **uart_hws[ARRAY_SIZE(uart_clk_ids) + 1];
-
 static int imx8mn_clocks_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct device_node *np = dev->of_node;
 	void __iomem *base;
-	int ret, i;
+	int ret;
 
 	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
 					  IMX8MN_CLK_END), GFP_KERNEL);
@@ -585,13 +577,7 @@ static int imx8mn_clocks_probe(struct platform_device *pdev)
 		goto unregister_hws;
 	}
 
-	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
-		int index = uart_clk_ids[i];
-
-		uart_hws[i] = &hws[index]->clk;
-	}
-
-	imx_register_uart_clocks(uart_hws);
+	imx_register_uart_clocks(4);
 
 	return 0;
 
diff --git a/drivers/clk/imx/clk-imx8mp.c b/drivers/clk/imx/clk-imx8mp.c
index 2f4e1d674e1c..3e6557e7d559 100644
--- a/drivers/clk/imx/clk-imx8mp.c
+++ b/drivers/clk/imx/clk-imx8mp.c
@@ -414,20 +414,11 @@ static const char * const imx8mp_dram_core_sels[] = {"dram_pll_out", "dram_alt_r
 static struct clk_hw **hws;
 static struct clk_hw_onecell_data *clk_hw_data;
 
-static const int uart_clk_ids[] = {
-	IMX8MP_CLK_UART1_ROOT,
-	IMX8MP_CLK_UART2_ROOT,
-	IMX8MP_CLK_UART3_ROOT,
-	IMX8MP_CLK_UART4_ROOT,
-};
-static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1];
-
 static int imx8mp_clocks_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct device_node *np;
 	void __iomem *anatop_base, *ccm_base;
-	int i;
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx8mp-anatop");
 	anatop_base = of_iomap(np, 0);
@@ -737,13 +728,7 @@ static int imx8mp_clocks_probe(struct platform_device *pdev)
 
 	of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_hw_data);
 
-	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
-		int index = uart_clk_ids[i];
-
-		uart_clks[i] = &hws[index]->clk;
-	}
-
-	imx_register_uart_clocks(uart_clks);
+	imx_register_uart_clocks(4);
 
 	return 0;
 }
diff --git a/drivers/clk/imx/clk-imx8mq.c b/drivers/clk/imx/clk-imx8mq.c
index 4dd4ae9d022b..3e1a10d3f55c 100644
--- a/drivers/clk/imx/clk-imx8mq.c
+++ b/drivers/clk/imx/clk-imx8mq.c
@@ -281,20 +281,12 @@ static const char * const pllout_monitor_sels[] = {"osc_25m", "osc_27m", "dummy"
 static struct clk_hw_onecell_data *clk_hw_data;
 static struct clk_hw **hws;
 
-static const int uart_clk_ids[] = {
-	IMX8MQ_CLK_UART1_ROOT,
-	IMX8MQ_CLK_UART2_ROOT,
-	IMX8MQ_CLK_UART3_ROOT,
-	IMX8MQ_CLK_UART4_ROOT,
-};
-static struct clk **uart_hws[ARRAY_SIZE(uart_clk_ids) + 1];
-
 static int imx8mq_clocks_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct device_node *np = dev->of_node;
 	void __iomem *base;
-	int err, i;
+	int err;
 
 	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
 					  IMX8MQ_CLK_END), GFP_KERNEL);
@@ -629,13 +621,7 @@ static int imx8mq_clocks_probe(struct platform_device *pdev)
 		goto unregister_hws;
 	}
 
-	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
-		int index = uart_clk_ids[i];
-
-		uart_hws[i] = &hws[index]->clk;
-	}
-
-	imx_register_uart_clocks(uart_hws);
+	imx_register_uart_clocks(4);
 
 	return 0;
 
diff --git a/drivers/clk/imx/clk.c b/drivers/clk/imx/clk.c
index 47882c51cb85..35e41b9a4e34 100644
--- a/drivers/clk/imx/clk.c
+++ b/drivers/clk/imx/clk.c
@@ -147,8 +147,10 @@ void imx_cscmr1_fixup(u32 *val)
 }
 
 #ifndef MODULE
-static int imx_keep_uart_clocks;
-static struct clk ** const *imx_uart_clocks;
+
+static bool imx_keep_uart_clocks;
+static int imx_enabled_uart_clocks;
+static struct clk **imx_uart_clocks;
 
 static int __init imx_keep_uart_clocks_param(char *str)
 {
@@ -161,24 +163,45 @@ __setup_param("earlycon", imx_keep_uart_earlycon,
 __setup_param("earlyprintk", imx_keep_uart_earlyprintk,
 	      imx_keep_uart_clocks_param, 0);
 
-void imx_register_uart_clocks(struct clk ** const clks[])
+void imx_register_uart_clocks(unsigned int clk_count)
 {
+	imx_enabled_uart_clocks = 0;
+
+/* i.MX boards use device trees now.  For build tests without CONFIG_OF, do nothing */
+#ifdef CONFIG_OF
 	if (imx_keep_uart_clocks) {
 		int i;
 
-		imx_uart_clocks = clks;
-		for (i = 0; imx_uart_clocks[i]; i++)
-			clk_prepare_enable(*imx_uart_clocks[i]);
+		imx_uart_clocks = kcalloc(clk_count, sizeof(struct clk *), GFP_KERNEL);
+
+		if (!of_stdout)
+			return;
+
+		for (i = 0; i < clk_count; i++) {
+			imx_uart_clocks[imx_enabled_uart_clocks] = of_clk_get(of_stdout, i);
+
+			/* Stop if there are no more of_stdout references */
+			if (IS_ERR(imx_uart_clocks[imx_enabled_uart_clocks]))
+				return;
+
+			/* Only enable the clock if it's not NULL */
+			if (imx_uart_clocks[imx_enabled_uart_clocks])
+				clk_prepare_enable(imx_uart_clocks[imx_enabled_uart_clocks++]);
+		}
 	}
+#endif
 }
 
 static int __init imx_clk_disable_uart(void)
 {
-	if (imx_keep_uart_clocks && imx_uart_clocks) {
+	if (imx_keep_uart_clocks && imx_enabled_uart_clocks) {
 		int i;
 
-		for (i = 0; imx_uart_clocks[i]; i++)
-			clk_disable_unprepare(*imx_uart_clocks[i]);
+		for (i = 0; i < imx_enabled_uart_clocks; i++) {
+			clk_disable_unprepare(imx_uart_clocks[i]);
+			clk_put(imx_uart_clocks[i]);
+		};
+		kfree(imx_uart_clocks);
 	}
 
 	return 0;
diff --git a/drivers/clk/imx/clk.h b/drivers/clk/imx/clk.h
index 4f04c8287286..7571603bee23 100644
--- a/drivers/clk/imx/clk.h
+++ b/drivers/clk/imx/clk.h
@@ -11,9 +11,9 @@ extern spinlock_t imx_ccm_lock;
 void imx_check_clocks(struct clk *clks[], unsigned int count);
 void imx_check_clk_hws(struct clk_hw *clks[], unsigned int count);
 #ifndef MODULE
-void imx_register_uart_clocks(struct clk ** const clks[]);
+void imx_register_uart_clocks(unsigned int clk_count);
 #else
-static inline void imx_register_uart_clocks(struct clk ** const clks[])
+static inline void imx_register_uart_clocks(unsigned int clk_count)
 {
 }
 #endif
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 7+ messages in thread

* Re: [PATCH V4] clk: imx: Fix reparenting of UARTs not associated with stdout
  2021-03-13 12:28 [PATCH V4] clk: imx: Fix reparenting of UARTs not associated with stdout Adam Ford
@ 2021-03-13 15:16 ` Ahmad Fatoum
  2021-03-14  9:40   ` Ahmad Fatoum
  2021-03-22 21:42 ` Abel Vesa
  1 sibling, 1 reply; 7+ messages in thread
From: Ahmad Fatoum @ 2021-03-13 15:16 UTC (permalink / raw)
  To: Adam Ford, linux-clk
  Cc: aford, Aisheng Dong, Abel Vesa, Michael Turquette, Stephen Boyd,
	Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam,
	NXP Linux Team, Jerome Brunet, Linus Walleij, linux-arm-kernel,
	linux-kernel

Hi,

On 13.03.21 13:28, Adam Ford wrote:
> Most if not all i.MX SoC's call a function which enables all UARTS.
> This is a problem for users who need to re-parent the clock source,
> because any attempt to change the parent results in an busy error
> due to the fact that the clocks have been enabled already.
> 
>   clk: failed to reparent uart1 to sys_pll1_80m: -16
> 
> Instead of pre-initializing all UARTS, scan the device tree to see
> which UART clocks are associated to stdout, and only enable those
> UART clocks if it's needed early.  This will move initialization of
> the remaining clocks until after the parenting of the clocks.
> 
> When the clocks are shutdown, this mechanism will also disable any
> clocks that were pre-initialized.
> 
> Fixes: 9461f7b33d11c ("clk: fix CLK_SET_RATE_GATE with clock rate protection")
> Suggested-by: Aisheng Dong <aisheng.dong@nxp.com>
> Signed-off-by: Adam Ford <aford173@gmail.com>
> Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
> Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
> 
> ---
> V4:  Check if of_stdout is available before using it.
>      Re-align #ifdef to remove repeated code.
> V3:  Return a method more closely related to upstream kernel but
>      instead of passing an array of UART's, each SoC passes the max
>      number of UART clocks is has.  The imx clock driver will create
>      an array to enable on startup, and disable later.
> V2:  Attempt to port driver from vendor kernel.
> ---
>  drivers/clk/imx/clk-imx25.c   | 12 +---------
>  drivers/clk/imx/clk-imx27.c   | 13 +----------
>  drivers/clk/imx/clk-imx35.c   | 10 +--------
>  drivers/clk/imx/clk-imx5.c    | 30 +++----------------------
>  drivers/clk/imx/clk-imx6q.c   | 16 +-------------
>  drivers/clk/imx/clk-imx6sl.c  | 16 +-------------
>  drivers/clk/imx/clk-imx6sll.c | 24 +-------------------
>  drivers/clk/imx/clk-imx6sx.c  | 16 +-------------
>  drivers/clk/imx/clk-imx7d.c   | 22 +------------------
>  drivers/clk/imx/clk-imx7ulp.c | 31 ++------------------------
>  drivers/clk/imx/clk-imx8mm.c  | 18 ++-------------
>  drivers/clk/imx/clk-imx8mn.c  | 18 ++-------------
>  drivers/clk/imx/clk-imx8mp.c  | 17 +--------------
>  drivers/clk/imx/clk-imx8mq.c  | 18 ++-------------
>  drivers/clk/imx/clk.c         | 41 +++++++++++++++++++++++++++--------
>  drivers/clk/imx/clk.h         |  4 ++--
>  16 files changed, 54 insertions(+), 252 deletions(-)
> 
> diff --git a/drivers/clk/imx/clk-imx25.c b/drivers/clk/imx/clk-imx25.c
> index a66cabfbf94f..66192fe0a898 100644
> --- a/drivers/clk/imx/clk-imx25.c
> +++ b/drivers/clk/imx/clk-imx25.c
> @@ -73,16 +73,6 @@ enum mx25_clks {
>  
>  static struct clk *clk[clk_max];
>  
> -static struct clk ** const uart_clks[] __initconst = {
> -	&clk[uart_ipg_per],
> -	&clk[uart1_ipg],
> -	&clk[uart2_ipg],
> -	&clk[uart3_ipg],
> -	&clk[uart4_ipg],
> -	&clk[uart5_ipg],
> -	NULL
> -};
> -
>  static int __init __mx25_clocks_init(void __iomem *ccm_base)
>  {
>  	BUG_ON(!ccm_base);
> @@ -228,7 +218,7 @@ static int __init __mx25_clocks_init(void __iomem *ccm_base)
>  	 */
>  	clk_set_parent(clk[cko_sel], clk[ipg]);
>  
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(6);
>  
>  	return 0;
>  }
> diff --git a/drivers/clk/imx/clk-imx27.c b/drivers/clk/imx/clk-imx27.c
> index 5585ded8b8c6..56a5fc402b10 100644
> --- a/drivers/clk/imx/clk-imx27.c
> +++ b/drivers/clk/imx/clk-imx27.c
> @@ -49,17 +49,6 @@ static const char *ssi_sel_clks[] = { "spll_gate", "mpll", };
>  static struct clk *clk[IMX27_CLK_MAX];
>  static struct clk_onecell_data clk_data;
>  
> -static struct clk ** const uart_clks[] __initconst = {
> -	&clk[IMX27_CLK_PER1_GATE],
> -	&clk[IMX27_CLK_UART1_IPG_GATE],
> -	&clk[IMX27_CLK_UART2_IPG_GATE],
> -	&clk[IMX27_CLK_UART3_IPG_GATE],
> -	&clk[IMX27_CLK_UART4_IPG_GATE],
> -	&clk[IMX27_CLK_UART5_IPG_GATE],
> -	&clk[IMX27_CLK_UART6_IPG_GATE],
> -	NULL
> -};
> -
>  static void __init _mx27_clocks_init(unsigned long fref)
>  {
>  	BUG_ON(!ccm);
> @@ -176,7 +165,7 @@ static void __init _mx27_clocks_init(unsigned long fref)
>  
>  	clk_prepare_enable(clk[IMX27_CLK_EMI_AHB_GATE]);
>  
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(7);
>  
>  	imx_print_silicon_rev("i.MX27", mx27_revision());
>  }
> diff --git a/drivers/clk/imx/clk-imx35.c b/drivers/clk/imx/clk-imx35.c
> index c1df03665c09..0fe5ac210156 100644
> --- a/drivers/clk/imx/clk-imx35.c
> +++ b/drivers/clk/imx/clk-imx35.c
> @@ -82,14 +82,6 @@ enum mx35_clks {
>  
>  static struct clk *clk[clk_max];
>  
> -static struct clk ** const uart_clks[] __initconst = {
> -	&clk[ipg],
> -	&clk[uart1_gate],
> -	&clk[uart2_gate],
> -	&clk[uart3_gate],
> -	NULL
> -};
> -
>  static void __init _mx35_clocks_init(void)
>  {
>  	void __iomem *base;
> @@ -243,7 +235,7 @@ static void __init _mx35_clocks_init(void)
>  	 */
>  	clk_prepare_enable(clk[scc_gate]);
>  
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(4);
>  
>  	imx_print_silicon_rev("i.MX35", mx35_revision());
>  }
> diff --git a/drivers/clk/imx/clk-imx5.c b/drivers/clk/imx/clk-imx5.c
> index 01e079b81026..e4493846454d 100644
> --- a/drivers/clk/imx/clk-imx5.c
> +++ b/drivers/clk/imx/clk-imx5.c
> @@ -128,30 +128,6 @@ static const char *ieee1588_sels[] = { "pll3_sw", "pll4_sw", "dummy" /* usbphy2_
>  static struct clk *clk[IMX5_CLK_END];
>  static struct clk_onecell_data clk_data;
>  
> -static struct clk ** const uart_clks_mx51[] __initconst = {
> -	&clk[IMX5_CLK_UART1_IPG_GATE],
> -	&clk[IMX5_CLK_UART1_PER_GATE],
> -	&clk[IMX5_CLK_UART2_IPG_GATE],
> -	&clk[IMX5_CLK_UART2_PER_GATE],
> -	&clk[IMX5_CLK_UART3_IPG_GATE],
> -	&clk[IMX5_CLK_UART3_PER_GATE],
> -	NULL
> -};
> -
> -static struct clk ** const uart_clks_mx50_mx53[] __initconst = {
> -	&clk[IMX5_CLK_UART1_IPG_GATE],
> -	&clk[IMX5_CLK_UART1_PER_GATE],
> -	&clk[IMX5_CLK_UART2_IPG_GATE],
> -	&clk[IMX5_CLK_UART2_PER_GATE],
> -	&clk[IMX5_CLK_UART3_IPG_GATE],
> -	&clk[IMX5_CLK_UART3_PER_GATE],
> -	&clk[IMX5_CLK_UART4_IPG_GATE],
> -	&clk[IMX5_CLK_UART4_PER_GATE],
> -	&clk[IMX5_CLK_UART5_IPG_GATE],
> -	&clk[IMX5_CLK_UART5_PER_GATE],
> -	NULL
> -};
> -
>  static void __init mx5_clocks_common_init(void __iomem *ccm_base)
>  {
>  	clk[IMX5_CLK_DUMMY]		= imx_clk_fixed("dummy", 0);
> @@ -382,7 +358,7 @@ static void __init mx50_clocks_init(struct device_node *np)
>  	r = clk_round_rate(clk[IMX5_CLK_USBOH3_PER_GATE], 54000000);
>  	clk_set_rate(clk[IMX5_CLK_USBOH3_PER_GATE], r);
>  
> -	imx_register_uart_clocks(uart_clks_mx50_mx53);
> +	imx_register_uart_clocks(5);
>  }
>  CLK_OF_DECLARE(imx50_ccm, "fsl,imx50-ccm", mx50_clocks_init);
>  
> @@ -488,7 +464,7 @@ static void __init mx51_clocks_init(struct device_node *np)
>  	val |= 1 << 23;
>  	writel(val, MXC_CCM_CLPCR);
>  
> -	imx_register_uart_clocks(uart_clks_mx51);
> +	imx_register_uart_clocks(3);
>  }
>  CLK_OF_DECLARE(imx51_ccm, "fsl,imx51-ccm", mx51_clocks_init);
>  
> @@ -633,6 +609,6 @@ static void __init mx53_clocks_init(struct device_node *np)
>  	r = clk_round_rate(clk[IMX5_CLK_USBOH3_PER_GATE], 54000000);
>  	clk_set_rate(clk[IMX5_CLK_USBOH3_PER_GATE], r);
>  
> -	imx_register_uart_clocks(uart_clks_mx50_mx53);
> +	imx_register_uart_clocks(5);
>  }
>  CLK_OF_DECLARE(imx53_ccm, "fsl,imx53-ccm", mx53_clocks_init);
> diff --git a/drivers/clk/imx/clk-imx6q.c b/drivers/clk/imx/clk-imx6q.c
> index 521d6136d22c..496900de0b0b 100644
> --- a/drivers/clk/imx/clk-imx6q.c
> +++ b/drivers/clk/imx/clk-imx6q.c
> @@ -140,13 +140,6 @@ static inline int clk_on_imx6dl(void)
>  	return of_machine_is_compatible("fsl,imx6dl");
>  }
>  
> -static const int uart_clk_ids[] __initconst = {
> -	IMX6QDL_CLK_UART_IPG,
> -	IMX6QDL_CLK_UART_SERIAL,
> -};
> -
> -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
> -
>  static int ldb_di_sel_by_clock_id(int clock_id)
>  {
>  	switch (clock_id) {
> @@ -440,7 +433,6 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
>  	struct device_node *np;
>  	void __iomem *anatop_base, *base;
>  	int ret;
> -	int i;
>  
>  	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
>  					  IMX6QDL_CLK_END), GFP_KERNEL);
> @@ -982,12 +974,6 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
>  			       hws[IMX6QDL_CLK_PLL3_USB_OTG]->clk);
>  	}
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_clks[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(1);
>  }
>  CLK_OF_DECLARE(imx6q, "fsl,imx6q-ccm", imx6q_clocks_init);
> diff --git a/drivers/clk/imx/clk-imx6sl.c b/drivers/clk/imx/clk-imx6sl.c
> index 29eab05c9068..277365970320 100644
> --- a/drivers/clk/imx/clk-imx6sl.c
> +++ b/drivers/clk/imx/clk-imx6sl.c
> @@ -179,19 +179,11 @@ void imx6sl_set_wait_clk(bool enter)
>  		imx6sl_enable_pll_arm(false);
>  }
>  
> -static const int uart_clk_ids[] __initconst = {
> -	IMX6SL_CLK_UART,
> -	IMX6SL_CLK_UART_SERIAL,
> -};
> -
> -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
> -
>  static void __init imx6sl_clocks_init(struct device_node *ccm_node)
>  {
>  	struct device_node *np;
>  	void __iomem *base;
>  	int ret;
> -	int i;
>  
>  	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
>  					  IMX6SL_CLK_END), GFP_KERNEL);
> @@ -448,12 +440,6 @@ static void __init imx6sl_clocks_init(struct device_node *ccm_node)
>  	clk_set_parent(hws[IMX6SL_CLK_LCDIF_AXI_SEL]->clk,
>  		       hws[IMX6SL_CLK_PLL2_PFD2]->clk);
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_clks[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(2);
>  }
>  CLK_OF_DECLARE(imx6sl, "fsl,imx6sl-ccm", imx6sl_clocks_init);
> diff --git a/drivers/clk/imx/clk-imx6sll.c b/drivers/clk/imx/clk-imx6sll.c
> index 8e8288bda4d0..31d777f30039 100644
> --- a/drivers/clk/imx/clk-imx6sll.c
> +++ b/drivers/clk/imx/clk-imx6sll.c
> @@ -76,26 +76,10 @@ static u32 share_count_ssi1;
>  static u32 share_count_ssi2;
>  static u32 share_count_ssi3;
>  
> -static const int uart_clk_ids[] __initconst = {
> -	IMX6SLL_CLK_UART1_IPG,
> -	IMX6SLL_CLK_UART1_SERIAL,
> -	IMX6SLL_CLK_UART2_IPG,
> -	IMX6SLL_CLK_UART2_SERIAL,
> -	IMX6SLL_CLK_UART3_IPG,
> -	IMX6SLL_CLK_UART3_SERIAL,
> -	IMX6SLL_CLK_UART4_IPG,
> -	IMX6SLL_CLK_UART4_SERIAL,
> -	IMX6SLL_CLK_UART5_IPG,
> -	IMX6SLL_CLK_UART5_SERIAL,
> -};
> -
> -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
> -
>  static void __init imx6sll_clocks_init(struct device_node *ccm_node)
>  {
>  	struct device_node *np;
>  	void __iomem *base;
> -	int i;
>  
>  	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
>  					  IMX6SLL_CLK_END), GFP_KERNEL);
> @@ -356,13 +340,7 @@ static void __init imx6sll_clocks_init(struct device_node *ccm_node)
>  
>  	of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_hw_data);
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_clks[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(5);
>  
>  	/* Lower the AHB clock rate before changing the clock source. */
>  	clk_set_rate(hws[IMX6SLL_CLK_AHB]->clk, 99000000);
> diff --git a/drivers/clk/imx/clk-imx6sx.c b/drivers/clk/imx/clk-imx6sx.c
> index 20dcce526d07..fc1bd23d4583 100644
> --- a/drivers/clk/imx/clk-imx6sx.c
> +++ b/drivers/clk/imx/clk-imx6sx.c
> @@ -117,18 +117,10 @@ static u32 share_count_ssi3;
>  static u32 share_count_sai1;
>  static u32 share_count_sai2;
>  
> -static const int uart_clk_ids[] __initconst = {
> -	IMX6SX_CLK_UART_IPG,
> -	IMX6SX_CLK_UART_SERIAL,
> -};
> -
> -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
> -
>  static void __init imx6sx_clocks_init(struct device_node *ccm_node)
>  {
>  	struct device_node *np;
>  	void __iomem *base;
> -	int i;
>  
>  	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
>  					  IMX6SX_CLK_CLK_END), GFP_KERNEL);
> @@ -556,12 +548,6 @@ static void __init imx6sx_clocks_init(struct device_node *ccm_node)
>  	clk_set_parent(hws[IMX6SX_CLK_QSPI1_SEL]->clk, hws[IMX6SX_CLK_PLL2_BUS]->clk);
>  	clk_set_parent(hws[IMX6SX_CLK_QSPI2_SEL]->clk, hws[IMX6SX_CLK_PLL2_BUS]->clk);
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_clks[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(2);
>  }
>  CLK_OF_DECLARE(imx6sx, "fsl,imx6sx-ccm", imx6sx_clocks_init);
> diff --git a/drivers/clk/imx/clk-imx7d.c b/drivers/clk/imx/clk-imx7d.c
> index 22d24a6a05e7..c4e0f1c07192 100644
> --- a/drivers/clk/imx/clk-imx7d.c
> +++ b/drivers/clk/imx/clk-imx7d.c
> @@ -377,23 +377,10 @@ static const char *pll_video_bypass_sel[] = { "pll_video_main", "pll_video_main_
>  static struct clk_hw **hws;
>  static struct clk_hw_onecell_data *clk_hw_data;
>  
> -static const int uart_clk_ids[] __initconst = {
> -	IMX7D_UART1_ROOT_CLK,
> -	IMX7D_UART2_ROOT_CLK,
> -	IMX7D_UART3_ROOT_CLK,
> -	IMX7D_UART4_ROOT_CLK,
> -	IMX7D_UART5_ROOT_CLK,
> -	IMX7D_UART6_ROOT_CLK,
> -	IMX7D_UART7_ROOT_CLK,
> -};
> -
> -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
> -
>  static void __init imx7d_clocks_init(struct device_node *ccm_node)
>  {
>  	struct device_node *np;
>  	void __iomem *base;
> -	int i;
>  
>  	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
>  					  IMX7D_CLK_END), GFP_KERNEL);
> @@ -897,14 +884,7 @@ static void __init imx7d_clocks_init(struct device_node *ccm_node)
>  	hws[IMX7D_USB1_MAIN_480M_CLK] = imx_clk_hw_fixed_factor("pll_usb1_main_clk", "osc", 20, 1);
>  	hws[IMX7D_USB_MAIN_480M_CLK] = imx_clk_hw_fixed_factor("pll_usb_main_clk", "osc", 20, 1);
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_clks[i] = &hws[index]->clk;
> -	}
> -
> -
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(7);
>  
>  }
>  CLK_OF_DECLARE(imx7d, "fsl,imx7d-ccm", imx7d_clocks_init);
> diff --git a/drivers/clk/imx/clk-imx7ulp.c b/drivers/clk/imx/clk-imx7ulp.c
> index 634c0b6636b0..779e09105da7 100644
> --- a/drivers/clk/imx/clk-imx7ulp.c
> +++ b/drivers/clk/imx/clk-imx7ulp.c
> @@ -43,19 +43,6 @@ static const struct clk_div_table ulp_div_table[] = {
>  	{ /* sentinel */ },
>  };
>  
> -static const int pcc2_uart_clk_ids[] __initconst = {
> -	IMX7ULP_CLK_LPUART4,
> -	IMX7ULP_CLK_LPUART5,
> -};
> -
> -static const int pcc3_uart_clk_ids[] __initconst = {
> -	IMX7ULP_CLK_LPUART6,
> -	IMX7ULP_CLK_LPUART7,
> -};
> -
> -static struct clk **pcc2_uart_clks[ARRAY_SIZE(pcc2_uart_clk_ids) + 1] __initdata;
> -static struct clk **pcc3_uart_clks[ARRAY_SIZE(pcc3_uart_clk_ids) + 1] __initdata;
> -
>  static void __init imx7ulp_clk_scg1_init(struct device_node *np)
>  {
>  	struct clk_hw_onecell_data *clk_data;
> @@ -150,7 +137,6 @@ static void __init imx7ulp_clk_pcc2_init(struct device_node *np)
>  	struct clk_hw_onecell_data *clk_data;
>  	struct clk_hw **hws;
>  	void __iomem *base;
> -	int i;
>  
>  	clk_data = kzalloc(struct_size(clk_data, hws, IMX7ULP_CLK_PCC2_END),
>  			   GFP_KERNEL);
> @@ -190,13 +176,7 @@ static void __init imx7ulp_clk_pcc2_init(struct device_node *np)
>  
>  	of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_data);
>  
> -	for (i = 0; i < ARRAY_SIZE(pcc2_uart_clk_ids); i++) {
> -		int index = pcc2_uart_clk_ids[i];
> -
> -		pcc2_uart_clks[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(pcc2_uart_clks);
> +	imx_register_uart_clocks(2);
>  }
>  CLK_OF_DECLARE(imx7ulp_clk_pcc2, "fsl,imx7ulp-pcc2", imx7ulp_clk_pcc2_init);
>  
> @@ -205,7 +185,6 @@ static void __init imx7ulp_clk_pcc3_init(struct device_node *np)
>  	struct clk_hw_onecell_data *clk_data;
>  	struct clk_hw **hws;
>  	void __iomem *base;
> -	int i;
>  
>  	clk_data = kzalloc(struct_size(clk_data, hws, IMX7ULP_CLK_PCC3_END),
>  			   GFP_KERNEL);
> @@ -244,13 +223,7 @@ static void __init imx7ulp_clk_pcc3_init(struct device_node *np)
>  
>  	of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_data);
>  
> -	for (i = 0; i < ARRAY_SIZE(pcc3_uart_clk_ids); i++) {
> -		int index = pcc3_uart_clk_ids[i];
> -
> -		pcc3_uart_clks[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(pcc3_uart_clks);
> +	imx_register_uart_clocks(7);
>  }
>  CLK_OF_DECLARE(imx7ulp_clk_pcc3, "fsl,imx7ulp-pcc3", imx7ulp_clk_pcc3_init);
>  
> diff --git a/drivers/clk/imx/clk-imx8mm.c b/drivers/clk/imx/clk-imx8mm.c
> index 6a01eec36dd0..f1919fafb124 100644
> --- a/drivers/clk/imx/clk-imx8mm.c
> +++ b/drivers/clk/imx/clk-imx8mm.c
> @@ -296,20 +296,12 @@ static const char * const clkout_sels[] = {"audio_pll1_out", "audio_pll2_out", "
>  static struct clk_hw_onecell_data *clk_hw_data;
>  static struct clk_hw **hws;
>  
> -static const int uart_clk_ids[] = {
> -	IMX8MM_CLK_UART1_ROOT,
> -	IMX8MM_CLK_UART2_ROOT,
> -	IMX8MM_CLK_UART3_ROOT,
> -	IMX8MM_CLK_UART4_ROOT,
> -};
> -static struct clk **uart_hws[ARRAY_SIZE(uart_clk_ids) + 1];
> -
>  static int imx8mm_clocks_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
>  	struct device_node *np = dev->of_node;
>  	void __iomem *base;
> -	int ret, i;
> +	int ret;
>  
>  	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
>  					  IMX8MM_CLK_END), GFP_KERNEL);
> @@ -634,13 +626,7 @@ static int imx8mm_clocks_probe(struct platform_device *pdev)
>  		goto unregister_hws;
>  	}
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_hws[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(uart_hws);
> +	imx_register_uart_clocks(4);
>  
>  	return 0;
>  
> diff --git a/drivers/clk/imx/clk-imx8mn.c b/drivers/clk/imx/clk-imx8mn.c
> index 324c5fd0aa04..88f6630cd472 100644
> --- a/drivers/clk/imx/clk-imx8mn.c
> +++ b/drivers/clk/imx/clk-imx8mn.c
> @@ -289,20 +289,12 @@ static const char * const clkout_sels[] = {"audio_pll1_out", "audio_pll2_out", "
>  static struct clk_hw_onecell_data *clk_hw_data;
>  static struct clk_hw **hws;
>  
> -static const int uart_clk_ids[] = {
> -	IMX8MN_CLK_UART1_ROOT,
> -	IMX8MN_CLK_UART2_ROOT,
> -	IMX8MN_CLK_UART3_ROOT,
> -	IMX8MN_CLK_UART4_ROOT,
> -};
> -static struct clk **uart_hws[ARRAY_SIZE(uart_clk_ids) + 1];
> -
>  static int imx8mn_clocks_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
>  	struct device_node *np = dev->of_node;
>  	void __iomem *base;
> -	int ret, i;
> +	int ret;
>  
>  	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
>  					  IMX8MN_CLK_END), GFP_KERNEL);
> @@ -585,13 +577,7 @@ static int imx8mn_clocks_probe(struct platform_device *pdev)
>  		goto unregister_hws;
>  	}
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_hws[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(uart_hws);
> +	imx_register_uart_clocks(4);
>  
>  	return 0;
>  
> diff --git a/drivers/clk/imx/clk-imx8mp.c b/drivers/clk/imx/clk-imx8mp.c
> index 2f4e1d674e1c..3e6557e7d559 100644
> --- a/drivers/clk/imx/clk-imx8mp.c
> +++ b/drivers/clk/imx/clk-imx8mp.c
> @@ -414,20 +414,11 @@ static const char * const imx8mp_dram_core_sels[] = {"dram_pll_out", "dram_alt_r
>  static struct clk_hw **hws;
>  static struct clk_hw_onecell_data *clk_hw_data;
>  
> -static const int uart_clk_ids[] = {
> -	IMX8MP_CLK_UART1_ROOT,
> -	IMX8MP_CLK_UART2_ROOT,
> -	IMX8MP_CLK_UART3_ROOT,
> -	IMX8MP_CLK_UART4_ROOT,
> -};
> -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1];
> -
>  static int imx8mp_clocks_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
>  	struct device_node *np;
>  	void __iomem *anatop_base, *ccm_base;
> -	int i;
>  
>  	np = of_find_compatible_node(NULL, NULL, "fsl,imx8mp-anatop");
>  	anatop_base = of_iomap(np, 0);
> @@ -737,13 +728,7 @@ static int imx8mp_clocks_probe(struct platform_device *pdev)
>  
>  	of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_hw_data);
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_clks[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(4);
>  
>  	return 0;
>  }
> diff --git a/drivers/clk/imx/clk-imx8mq.c b/drivers/clk/imx/clk-imx8mq.c
> index 4dd4ae9d022b..3e1a10d3f55c 100644
> --- a/drivers/clk/imx/clk-imx8mq.c
> +++ b/drivers/clk/imx/clk-imx8mq.c
> @@ -281,20 +281,12 @@ static const char * const pllout_monitor_sels[] = {"osc_25m", "osc_27m", "dummy"
>  static struct clk_hw_onecell_data *clk_hw_data;
>  static struct clk_hw **hws;
>  
> -static const int uart_clk_ids[] = {
> -	IMX8MQ_CLK_UART1_ROOT,
> -	IMX8MQ_CLK_UART2_ROOT,
> -	IMX8MQ_CLK_UART3_ROOT,
> -	IMX8MQ_CLK_UART4_ROOT,
> -};
> -static struct clk **uart_hws[ARRAY_SIZE(uart_clk_ids) + 1];
> -
>  static int imx8mq_clocks_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
>  	struct device_node *np = dev->of_node;
>  	void __iomem *base;
> -	int err, i;
> +	int err;
>  
>  	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
>  					  IMX8MQ_CLK_END), GFP_KERNEL);
> @@ -629,13 +621,7 @@ static int imx8mq_clocks_probe(struct platform_device *pdev)
>  		goto unregister_hws;
>  	}
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_hws[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(uart_hws);
> +	imx_register_uart_clocks(4);
>  
>  	return 0;
>  
> diff --git a/drivers/clk/imx/clk.c b/drivers/clk/imx/clk.c
> index 47882c51cb85..35e41b9a4e34 100644
> --- a/drivers/clk/imx/clk.c
> +++ b/drivers/clk/imx/clk.c
> @@ -147,8 +147,10 @@ void imx_cscmr1_fixup(u32 *val)
>  }
>  
>  #ifndef MODULE
> -static int imx_keep_uart_clocks;
> -static struct clk ** const *imx_uart_clocks;
> +
> +static bool imx_keep_uart_clocks;
> +static int imx_enabled_uart_clocks;
> +static struct clk **imx_uart_clocks;
>  
>  static int __init imx_keep_uart_clocks_param(char *str)
>  {
> @@ -161,24 +163,45 @@ __setup_param("earlycon", imx_keep_uart_earlycon,
>  __setup_param("earlyprintk", imx_keep_uart_earlyprintk,
>  	      imx_keep_uart_clocks_param, 0);
>  
> -void imx_register_uart_clocks(struct clk ** const clks[])
> +void imx_register_uart_clocks(unsigned int clk_count)
>  {
> +	imx_enabled_uart_clocks = 0;
> +
> +/* i.MX boards use device trees now.  For build tests without CONFIG_OF, do nothing */
> +#ifdef CONFIG_OF
>  	if (imx_keep_uart_clocks) {
>  		int i;
>  
> -		imx_uart_clocks = clks;
> -		for (i = 0; imx_uart_clocks[i]; i++)
> -			clk_prepare_enable(*imx_uart_clocks[i]);
> +		imx_uart_clocks = kcalloc(clk_count, sizeof(struct clk *), GFP_KERNEL);
> +
> +		if (!of_stdout)
> +			return;

Memory leak. Just do if (imx_keep_uart_clocks && of_stdout)

> +
> +		for (i = 0; i < clk_count; i++) {
> +			imx_uart_clocks[imx_enabled_uart_clocks] = of_clk_get(of_stdout, i);
> +
> +			/* Stop if there are no more of_stdout references */
> +			if (IS_ERR(imx_uart_clocks[imx_enabled_uart_clocks]))
> +				return;
> +
> +			/* Only enable the clock if it's not NULL */
> +			if (imx_uart_clocks[imx_enabled_uart_clocks])
> +				clk_prepare_enable(imx_uart_clocks[imx_enabled_uart_clocks++]);
> +		}
>  	}
> +#endif
>  }
>  
>  static int __init imx_clk_disable_uart(void)
>  {
> -	if (imx_keep_uart_clocks && imx_uart_clocks) {
> +	if (imx_keep_uart_clocks && imx_enabled_uart_clocks) {
>  		int i;
>  
> -		for (i = 0; imx_uart_clocks[i]; i++)
> -			clk_disable_unprepare(*imx_uart_clocks[i]);
> +		for (i = 0; i < imx_enabled_uart_clocks; i++) {
> +			clk_disable_unprepare(imx_uart_clocks[i]);
> +			clk_put(imx_uart_clocks[i]);
> +		};
> +		kfree(imx_uart_clocks);
>  	}
>  
>  	return 0;
> diff --git a/drivers/clk/imx/clk.h b/drivers/clk/imx/clk.h
> index 4f04c8287286..7571603bee23 100644
> --- a/drivers/clk/imx/clk.h
> +++ b/drivers/clk/imx/clk.h
> @@ -11,9 +11,9 @@ extern spinlock_t imx_ccm_lock;
>  void imx_check_clocks(struct clk *clks[], unsigned int count);
>  void imx_check_clk_hws(struct clk_hw *clks[], unsigned int count);
>  #ifndef MODULE
> -void imx_register_uart_clocks(struct clk ** const clks[]);
> +void imx_register_uart_clocks(unsigned int clk_count);
>  #else
> -static inline void imx_register_uart_clocks(struct clk ** const clks[])
> +static inline void imx_register_uart_clocks(unsigned int clk_count)
>  {
>  }
>  #endif
> 

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH V4] clk: imx: Fix reparenting of UARTs not associated with stdout
  2021-03-13 15:16 ` Ahmad Fatoum
@ 2021-03-14  9:40   ` Ahmad Fatoum
  2021-03-20 23:00     ` Adam Ford
  0 siblings, 1 reply; 7+ messages in thread
From: Ahmad Fatoum @ 2021-03-14  9:40 UTC (permalink / raw)
  To: Adam Ford, linux-clk
  Cc: Aisheng Dong, Linus Walleij, Abel Vesa, Stephen Boyd,
	Fabio Estevam, Michael Turquette, aford, linux-kernel,
	NXP Linux Team, Pengutronix Kernel Team, Shawn Guo, Sascha Hauer,
	linux-arm-kernel, Jerome Brunet

On 13.03.21 16:16, Ahmad Fatoum wrote:
>> +/* i.MX boards use device trees now.  For build tests without CONFIG_OF, do nothing */
>> +#ifdef CONFIG_OF
>>  	if (imx_keep_uart_clocks) {
>>  		int i;
>>  
>> -		imx_uart_clocks = clks;
>> -		for (i = 0; imx_uart_clocks[i]; i++)
>> -			clk_prepare_enable(*imx_uart_clocks[i]);
>> +		imx_uart_clocks = kcalloc(clk_count, sizeof(struct clk *), GFP_KERNEL);
>> +
>> +		if (!of_stdout)
>> +			return;
> 
> Memory leak. Just do if (imx_keep_uart_clocks && of_stdout)

Please dismiss. I overlooked that you free it in a later initcall.

>>  static int __init imx_clk_disable_uart(void)
>>  {
>> -	if (imx_keep_uart_clocks && imx_uart_clocks) {
>> +	if (imx_keep_uart_clocks && imx_enabled_uart_clocks) {
>>  		int i;
>>  
>> -		for (i = 0; imx_uart_clocks[i]; i++)
>> -			clk_disable_unprepare(*imx_uart_clocks[i]);
>> +		for (i = 0; i < imx_enabled_uart_clocks; i++) {
>> +			clk_disable_unprepare(imx_uart_clocks[i]);
>> +			clk_put(imx_uart_clocks[i]);
>> +		};
>> +		kfree(imx_uart_clocks);
>>  	}

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH V4] clk: imx: Fix reparenting of UARTs not associated with stdout
  2021-03-14  9:40   ` Ahmad Fatoum
@ 2021-03-20 23:00     ` Adam Ford
  2021-03-22 11:05       ` Abel Vesa
  0 siblings, 1 reply; 7+ messages in thread
From: Adam Ford @ 2021-03-20 23:00 UTC (permalink / raw)
  To: Ahmad Fatoum
  Cc: linux-clk, Aisheng Dong, Linus Walleij, Abel Vesa, Stephen Boyd,
	Fabio Estevam, Michael Turquette, Adam Ford-BE,
	Linux Kernel Mailing List, NXP Linux Team,
	Pengutronix Kernel Team, Shawn Guo, Sascha Hauer, arm-soc,
	Jerome Brunet

On Sun, Mar 14, 2021 at 4:40 AM Ahmad Fatoum <a.fatoum@pengutronix.de> wrote:
>
> On 13.03.21 16:16, Ahmad Fatoum wrote:
> >> +/* i.MX boards use device trees now.  For build tests without CONFIG_OF, do nothing */
> >> +#ifdef CONFIG_OF
> >>      if (imx_keep_uart_clocks) {
> >>              int i;
> >>
> >> -            imx_uart_clocks = clks;
> >> -            for (i = 0; imx_uart_clocks[i]; i++)
> >> -                    clk_prepare_enable(*imx_uart_clocks[i]);
> >> +            imx_uart_clocks = kcalloc(clk_count, sizeof(struct clk *), GFP_KERNEL);
> >> +
> >> +            if (!of_stdout)
> >> +                    return;
> >
> > Memory leak. Just do if (imx_keep_uart_clocks && of_stdout)
>
> Please dismiss. I overlooked that you free it in a later initcall.

Abel,

Are you OK with this?  I also have a V5 posted [1] which does what
Ahmad suggested.

Either of these will fix reparenting issues, but I need this for
Bluetooth to operate correctly, because both beacon imx8mn and imx8mn
kits switch the UART parent to an 80MHz clock in order to run at
4Mbps.

thank you,

adam
>
> >>  static int __init imx_clk_disable_uart(void)
> >>  {
> >> -    if (imx_keep_uart_clocks && imx_uart_clocks) {
> >> +    if (imx_keep_uart_clocks && imx_enabled_uart_clocks) {
> >>              int i;
> >>
> >> -            for (i = 0; imx_uart_clocks[i]; i++)
> >> -                    clk_disable_unprepare(*imx_uart_clocks[i]);
> >> +            for (i = 0; i < imx_enabled_uart_clocks; i++) {
> >> +                    clk_disable_unprepare(imx_uart_clocks[i]);
> >> +                    clk_put(imx_uart_clocks[i]);
> >> +            };
> >> +            kfree(imx_uart_clocks);
> >>      }
>
> --
> Pengutronix e.K.                           |                             |
> Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
> 31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
> Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH V4] clk: imx: Fix reparenting of UARTs not associated with stdout
  2021-03-20 23:00     ` Adam Ford
@ 2021-03-22 11:05       ` Abel Vesa
  0 siblings, 0 replies; 7+ messages in thread
From: Abel Vesa @ 2021-03-22 11:05 UTC (permalink / raw)
  To: Adam Ford
  Cc: Ahmad Fatoum, linux-clk, Aisheng Dong, Linus Walleij, Abel Vesa,
	Stephen Boyd, Fabio Estevam, Michael Turquette, Adam Ford-BE,
	Linux Kernel Mailing List, NXP Linux Team,
	Pengutronix Kernel Team, Shawn Guo, Sascha Hauer, arm-soc,
	Jerome Brunet

On 21-03-20 18:00:25, Adam Ford wrote:
> On Sun, Mar 14, 2021 at 4:40 AM Ahmad Fatoum <a.fatoum@pengutronix.de> wrote:
> >
> > On 13.03.21 16:16, Ahmad Fatoum wrote:
> > >> +/* i.MX boards use device trees now.  For build tests without CONFIG_OF, do nothing */
> > >> +#ifdef CONFIG_OF
> > >>      if (imx_keep_uart_clocks) {
> > >>              int i;
> > >>
> > >> -            imx_uart_clocks = clks;
> > >> -            for (i = 0; imx_uart_clocks[i]; i++)
> > >> -                    clk_prepare_enable(*imx_uart_clocks[i]);
> > >> +            imx_uart_clocks = kcalloc(clk_count, sizeof(struct clk *), GFP_KERNEL);
> > >> +
> > >> +            if (!of_stdout)
> > >> +                    return;
> > >
> > > Memory leak. Just do if (imx_keep_uart_clocks && of_stdout)
> >
> > Please dismiss. I overlooked that you free it in a later initcall.
> 
> Abel,
> 
> Are you OK with this?  I also have a V5 posted [1] which does what
> Ahmad suggested.
> 

I'm OK with this version. Applied it on my clk/imx branch:
git://git.kernel.org/pub/scm/linux/kernel/git/abelvesa/linux.git

Thanks a lot for all the effort.

> Either of these will fix reparenting issues, but I need this for
> Bluetooth to operate correctly, because both beacon imx8mn and imx8mn
> kits switch the UART parent to an 80MHz clock in order to run at
> 4Mbps.
> 
> thank you,
> 
> adam
> >
> > >>  static int __init imx_clk_disable_uart(void)
> > >>  {
> > >> -    if (imx_keep_uart_clocks && imx_uart_clocks) {
> > >> +    if (imx_keep_uart_clocks && imx_enabled_uart_clocks) {
> > >>              int i;
> > >>
> > >> -            for (i = 0; imx_uart_clocks[i]; i++)
> > >> -                    clk_disable_unprepare(*imx_uart_clocks[i]);
> > >> +            for (i = 0; i < imx_enabled_uart_clocks; i++) {
> > >> +                    clk_disable_unprepare(imx_uart_clocks[i]);
> > >> +                    clk_put(imx_uart_clocks[i]);
> > >> +            };
> > >> +            kfree(imx_uart_clocks);
> > >>      }
> >
> > --
> > Pengutronix e.K.                           |                             |
> > Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
> > 31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
> > Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH V4] clk: imx: Fix reparenting of UARTs not associated with stdout
  2021-03-13 12:28 [PATCH V4] clk: imx: Fix reparenting of UARTs not associated with stdout Adam Ford
  2021-03-13 15:16 ` Ahmad Fatoum
@ 2021-03-22 21:42 ` Abel Vesa
  2021-03-24 17:06   ` Adam Ford
  1 sibling, 1 reply; 7+ messages in thread
From: Abel Vesa @ 2021-03-22 21:42 UTC (permalink / raw)
  To: Adam Ford
  Cc: linux-clk, aford, Aisheng Dong, Ahmad Fatoum, Michael Turquette,
	Stephen Boyd, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team,
	Fabio Estevam, NXP Linux Team, Jerome Brunet, Linus Walleij,
	linux-arm-kernel, linux-kernel

On 21-03-13 06:28:17, Adam Ford wrote:
> Most if not all i.MX SoC's call a function which enables all UARTS.
> This is a problem for users who need to re-parent the clock source,
> because any attempt to change the parent results in an busy error
> due to the fact that the clocks have been enabled already.
> 
>   clk: failed to reparent uart1 to sys_pll1_80m: -16
> 
> Instead of pre-initializing all UARTS, scan the device tree to see
> which UART clocks are associated to stdout, and only enable those
> UART clocks if it's needed early.  This will move initialization of
> the remaining clocks until after the parenting of the clocks.
> 
> When the clocks are shutdown, this mechanism will also disable any
> clocks that were pre-initialized.
> 
> Fixes: 9461f7b33d11c ("clk: fix CLK_SET_RATE_GATE with clock rate protection")
> Suggested-by: Aisheng Dong <aisheng.dong@nxp.com>
> Signed-off-by: Adam Ford <aford173@gmail.com>
> Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
> Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
> 
> ---
> V4:  Check if of_stdout is available before using it.
>      Re-align #ifdef to remove repeated code.
> V3:  Return a method more closely related to upstream kernel but
>      instead of passing an array of UART's, each SoC passes the max
>      number of UART clocks is has.  The imx clock driver will create
>      an array to enable on startup, and disable later.
> V2:  Attempt to port driver from vendor kernel.
> ---
>  drivers/clk/imx/clk-imx25.c   | 12 +---------
>  drivers/clk/imx/clk-imx27.c   | 13 +----------
>  drivers/clk/imx/clk-imx35.c   | 10 +--------
>  drivers/clk/imx/clk-imx5.c    | 30 +++----------------------
>  drivers/clk/imx/clk-imx6q.c   | 16 +-------------
>  drivers/clk/imx/clk-imx6sl.c  | 16 +-------------
>  drivers/clk/imx/clk-imx6sll.c | 24 +-------------------
>  drivers/clk/imx/clk-imx6sx.c  | 16 +-------------
>  drivers/clk/imx/clk-imx7d.c   | 22 +------------------
>  drivers/clk/imx/clk-imx7ulp.c | 31 ++------------------------
>  drivers/clk/imx/clk-imx8mm.c  | 18 ++-------------
>  drivers/clk/imx/clk-imx8mn.c  | 18 ++-------------
>  drivers/clk/imx/clk-imx8mp.c  | 17 +--------------
>  drivers/clk/imx/clk-imx8mq.c  | 18 ++-------------
>  drivers/clk/imx/clk.c         | 41 +++++++++++++++++++++++++++--------
>  drivers/clk/imx/clk.h         |  4 ++--
>  16 files changed, 54 insertions(+), 252 deletions(-)
> 
> diff --git a/drivers/clk/imx/clk-imx25.c b/drivers/clk/imx/clk-imx25.c
> index a66cabfbf94f..66192fe0a898 100644
> --- a/drivers/clk/imx/clk-imx25.c
> +++ b/drivers/clk/imx/clk-imx25.c
> @@ -73,16 +73,6 @@ enum mx25_clks {
>  
>  static struct clk *clk[clk_max];
>  
> -static struct clk ** const uart_clks[] __initconst = {
> -	&clk[uart_ipg_per],
> -	&clk[uart1_ipg],
> -	&clk[uart2_ipg],
> -	&clk[uart3_ipg],
> -	&clk[uart4_ipg],
> -	&clk[uart5_ipg],
> -	NULL
> -};
> -
>  static int __init __mx25_clocks_init(void __iomem *ccm_base)
>  {
>  	BUG_ON(!ccm_base);
> @@ -228,7 +218,7 @@ static int __init __mx25_clocks_init(void __iomem *ccm_base)
>  	 */
>  	clk_set_parent(clk[cko_sel], clk[ipg]);
>  
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(6);
>  
>  	return 0;
>  }
> diff --git a/drivers/clk/imx/clk-imx27.c b/drivers/clk/imx/clk-imx27.c
> index 5585ded8b8c6..56a5fc402b10 100644
> --- a/drivers/clk/imx/clk-imx27.c
> +++ b/drivers/clk/imx/clk-imx27.c
> @@ -49,17 +49,6 @@ static const char *ssi_sel_clks[] = { "spll_gate", "mpll", };
>  static struct clk *clk[IMX27_CLK_MAX];
>  static struct clk_onecell_data clk_data;
>  
> -static struct clk ** const uart_clks[] __initconst = {
> -	&clk[IMX27_CLK_PER1_GATE],
> -	&clk[IMX27_CLK_UART1_IPG_GATE],
> -	&clk[IMX27_CLK_UART2_IPG_GATE],
> -	&clk[IMX27_CLK_UART3_IPG_GATE],
> -	&clk[IMX27_CLK_UART4_IPG_GATE],
> -	&clk[IMX27_CLK_UART5_IPG_GATE],
> -	&clk[IMX27_CLK_UART6_IPG_GATE],
> -	NULL
> -};
> -
>  static void __init _mx27_clocks_init(unsigned long fref)
>  {
>  	BUG_ON(!ccm);
> @@ -176,7 +165,7 @@ static void __init _mx27_clocks_init(unsigned long fref)
>  
>  	clk_prepare_enable(clk[IMX27_CLK_EMI_AHB_GATE]);
>  
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(7);
>  
>  	imx_print_silicon_rev("i.MX27", mx27_revision());
>  }
> diff --git a/drivers/clk/imx/clk-imx35.c b/drivers/clk/imx/clk-imx35.c
> index c1df03665c09..0fe5ac210156 100644
> --- a/drivers/clk/imx/clk-imx35.c
> +++ b/drivers/clk/imx/clk-imx35.c
> @@ -82,14 +82,6 @@ enum mx35_clks {
>  
>  static struct clk *clk[clk_max];
>  
> -static struct clk ** const uart_clks[] __initconst = {
> -	&clk[ipg],
> -	&clk[uart1_gate],
> -	&clk[uart2_gate],
> -	&clk[uart3_gate],
> -	NULL
> -};
> -
>  static void __init _mx35_clocks_init(void)
>  {
>  	void __iomem *base;
> @@ -243,7 +235,7 @@ static void __init _mx35_clocks_init(void)
>  	 */
>  	clk_prepare_enable(clk[scc_gate]);
>  
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(4);
>  
>  	imx_print_silicon_rev("i.MX35", mx35_revision());
>  }
> diff --git a/drivers/clk/imx/clk-imx5.c b/drivers/clk/imx/clk-imx5.c
> index 01e079b81026..e4493846454d 100644
> --- a/drivers/clk/imx/clk-imx5.c
> +++ b/drivers/clk/imx/clk-imx5.c
> @@ -128,30 +128,6 @@ static const char *ieee1588_sels[] = { "pll3_sw", "pll4_sw", "dummy" /* usbphy2_
>  static struct clk *clk[IMX5_CLK_END];
>  static struct clk_onecell_data clk_data;
>  
> -static struct clk ** const uart_clks_mx51[] __initconst = {
> -	&clk[IMX5_CLK_UART1_IPG_GATE],
> -	&clk[IMX5_CLK_UART1_PER_GATE],
> -	&clk[IMX5_CLK_UART2_IPG_GATE],
> -	&clk[IMX5_CLK_UART2_PER_GATE],
> -	&clk[IMX5_CLK_UART3_IPG_GATE],
> -	&clk[IMX5_CLK_UART3_PER_GATE],
> -	NULL
> -};
> -
> -static struct clk ** const uart_clks_mx50_mx53[] __initconst = {
> -	&clk[IMX5_CLK_UART1_IPG_GATE],
> -	&clk[IMX5_CLK_UART1_PER_GATE],
> -	&clk[IMX5_CLK_UART2_IPG_GATE],
> -	&clk[IMX5_CLK_UART2_PER_GATE],
> -	&clk[IMX5_CLK_UART3_IPG_GATE],
> -	&clk[IMX5_CLK_UART3_PER_GATE],
> -	&clk[IMX5_CLK_UART4_IPG_GATE],
> -	&clk[IMX5_CLK_UART4_PER_GATE],
> -	&clk[IMX5_CLK_UART5_IPG_GATE],
> -	&clk[IMX5_CLK_UART5_PER_GATE],
> -	NULL
> -};
> -
>  static void __init mx5_clocks_common_init(void __iomem *ccm_base)
>  {
>  	clk[IMX5_CLK_DUMMY]		= imx_clk_fixed("dummy", 0);
> @@ -382,7 +358,7 @@ static void __init mx50_clocks_init(struct device_node *np)
>  	r = clk_round_rate(clk[IMX5_CLK_USBOH3_PER_GATE], 54000000);
>  	clk_set_rate(clk[IMX5_CLK_USBOH3_PER_GATE], r);
>  
> -	imx_register_uart_clocks(uart_clks_mx50_mx53);
> +	imx_register_uart_clocks(5);
>  }
>  CLK_OF_DECLARE(imx50_ccm, "fsl,imx50-ccm", mx50_clocks_init);
>  
> @@ -488,7 +464,7 @@ static void __init mx51_clocks_init(struct device_node *np)
>  	val |= 1 << 23;
>  	writel(val, MXC_CCM_CLPCR);
>  
> -	imx_register_uart_clocks(uart_clks_mx51);
> +	imx_register_uart_clocks(3);
>  }
>  CLK_OF_DECLARE(imx51_ccm, "fsl,imx51-ccm", mx51_clocks_init);
>  
> @@ -633,6 +609,6 @@ static void __init mx53_clocks_init(struct device_node *np)
>  	r = clk_round_rate(clk[IMX5_CLK_USBOH3_PER_GATE], 54000000);
>  	clk_set_rate(clk[IMX5_CLK_USBOH3_PER_GATE], r);
>  
> -	imx_register_uart_clocks(uart_clks_mx50_mx53);
> +	imx_register_uart_clocks(5);
>  }
>  CLK_OF_DECLARE(imx53_ccm, "fsl,imx53-ccm", mx53_clocks_init);
> diff --git a/drivers/clk/imx/clk-imx6q.c b/drivers/clk/imx/clk-imx6q.c
> index 521d6136d22c..496900de0b0b 100644
> --- a/drivers/clk/imx/clk-imx6q.c
> +++ b/drivers/clk/imx/clk-imx6q.c
> @@ -140,13 +140,6 @@ static inline int clk_on_imx6dl(void)
>  	return of_machine_is_compatible("fsl,imx6dl");
>  }
>  
> -static const int uart_clk_ids[] __initconst = {
> -	IMX6QDL_CLK_UART_IPG,
> -	IMX6QDL_CLK_UART_SERIAL,
> -};
> -
> -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
> -
>  static int ldb_di_sel_by_clock_id(int clock_id)
>  {
>  	switch (clock_id) {
> @@ -440,7 +433,6 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
>  	struct device_node *np;
>  	void __iomem *anatop_base, *base;
>  	int ret;
> -	int i;
>  
>  	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
>  					  IMX6QDL_CLK_END), GFP_KERNEL);
> @@ -982,12 +974,6 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
>  			       hws[IMX6QDL_CLK_PLL3_USB_OTG]->clk);
>  	}
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_clks[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(1);
>  }
>  CLK_OF_DECLARE(imx6q, "fsl,imx6q-ccm", imx6q_clocks_init);
> diff --git a/drivers/clk/imx/clk-imx6sl.c b/drivers/clk/imx/clk-imx6sl.c
> index 29eab05c9068..277365970320 100644
> --- a/drivers/clk/imx/clk-imx6sl.c
> +++ b/drivers/clk/imx/clk-imx6sl.c
> @@ -179,19 +179,11 @@ void imx6sl_set_wait_clk(bool enter)
>  		imx6sl_enable_pll_arm(false);
>  }
>  
> -static const int uart_clk_ids[] __initconst = {
> -	IMX6SL_CLK_UART,
> -	IMX6SL_CLK_UART_SERIAL,
> -};
> -
> -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
> -
>  static void __init imx6sl_clocks_init(struct device_node *ccm_node)
>  {
>  	struct device_node *np;
>  	void __iomem *base;
>  	int ret;
> -	int i;
>  
>  	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
>  					  IMX6SL_CLK_END), GFP_KERNEL);
> @@ -448,12 +440,6 @@ static void __init imx6sl_clocks_init(struct device_node *ccm_node)
>  	clk_set_parent(hws[IMX6SL_CLK_LCDIF_AXI_SEL]->clk,
>  		       hws[IMX6SL_CLK_PLL2_PFD2]->clk);
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_clks[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(2);
>  }
>  CLK_OF_DECLARE(imx6sl, "fsl,imx6sl-ccm", imx6sl_clocks_init);
> diff --git a/drivers/clk/imx/clk-imx6sll.c b/drivers/clk/imx/clk-imx6sll.c
> index 8e8288bda4d0..31d777f30039 100644
> --- a/drivers/clk/imx/clk-imx6sll.c
> +++ b/drivers/clk/imx/clk-imx6sll.c
> @@ -76,26 +76,10 @@ static u32 share_count_ssi1;
>  static u32 share_count_ssi2;
>  static u32 share_count_ssi3;
>  
> -static const int uart_clk_ids[] __initconst = {
> -	IMX6SLL_CLK_UART1_IPG,
> -	IMX6SLL_CLK_UART1_SERIAL,
> -	IMX6SLL_CLK_UART2_IPG,
> -	IMX6SLL_CLK_UART2_SERIAL,
> -	IMX6SLL_CLK_UART3_IPG,
> -	IMX6SLL_CLK_UART3_SERIAL,
> -	IMX6SLL_CLK_UART4_IPG,
> -	IMX6SLL_CLK_UART4_SERIAL,
> -	IMX6SLL_CLK_UART5_IPG,
> -	IMX6SLL_CLK_UART5_SERIAL,
> -};
> -
> -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
> -
>  static void __init imx6sll_clocks_init(struct device_node *ccm_node)
>  {
>  	struct device_node *np;
>  	void __iomem *base;
> -	int i;
>  
>  	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
>  					  IMX6SLL_CLK_END), GFP_KERNEL);
> @@ -356,13 +340,7 @@ static void __init imx6sll_clocks_init(struct device_node *ccm_node)
>  
>  	of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_hw_data);
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_clks[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(5);
>  
>  	/* Lower the AHB clock rate before changing the clock source. */
>  	clk_set_rate(hws[IMX6SLL_CLK_AHB]->clk, 99000000);
> diff --git a/drivers/clk/imx/clk-imx6sx.c b/drivers/clk/imx/clk-imx6sx.c
> index 20dcce526d07..fc1bd23d4583 100644
> --- a/drivers/clk/imx/clk-imx6sx.c
> +++ b/drivers/clk/imx/clk-imx6sx.c
> @@ -117,18 +117,10 @@ static u32 share_count_ssi3;
>  static u32 share_count_sai1;
>  static u32 share_count_sai2;
>  
> -static const int uart_clk_ids[] __initconst = {
> -	IMX6SX_CLK_UART_IPG,
> -	IMX6SX_CLK_UART_SERIAL,
> -};
> -
> -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
> -
>  static void __init imx6sx_clocks_init(struct device_node *ccm_node)
>  {
>  	struct device_node *np;
>  	void __iomem *base;
> -	int i;
>  
>  	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
>  					  IMX6SX_CLK_CLK_END), GFP_KERNEL);
> @@ -556,12 +548,6 @@ static void __init imx6sx_clocks_init(struct device_node *ccm_node)
>  	clk_set_parent(hws[IMX6SX_CLK_QSPI1_SEL]->clk, hws[IMX6SX_CLK_PLL2_BUS]->clk);
>  	clk_set_parent(hws[IMX6SX_CLK_QSPI2_SEL]->clk, hws[IMX6SX_CLK_PLL2_BUS]->clk);
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_clks[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(2);
>  }
>  CLK_OF_DECLARE(imx6sx, "fsl,imx6sx-ccm", imx6sx_clocks_init);
> diff --git a/drivers/clk/imx/clk-imx7d.c b/drivers/clk/imx/clk-imx7d.c
> index 22d24a6a05e7..c4e0f1c07192 100644
> --- a/drivers/clk/imx/clk-imx7d.c
> +++ b/drivers/clk/imx/clk-imx7d.c
> @@ -377,23 +377,10 @@ static const char *pll_video_bypass_sel[] = { "pll_video_main", "pll_video_main_
>  static struct clk_hw **hws;
>  static struct clk_hw_onecell_data *clk_hw_data;
>  
> -static const int uart_clk_ids[] __initconst = {
> -	IMX7D_UART1_ROOT_CLK,
> -	IMX7D_UART2_ROOT_CLK,
> -	IMX7D_UART3_ROOT_CLK,
> -	IMX7D_UART4_ROOT_CLK,
> -	IMX7D_UART5_ROOT_CLK,
> -	IMX7D_UART6_ROOT_CLK,
> -	IMX7D_UART7_ROOT_CLK,
> -};
> -
> -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
> -
>  static void __init imx7d_clocks_init(struct device_node *ccm_node)
>  {
>  	struct device_node *np;
>  	void __iomem *base;
> -	int i;
>  
>  	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
>  					  IMX7D_CLK_END), GFP_KERNEL);
> @@ -897,14 +884,7 @@ static void __init imx7d_clocks_init(struct device_node *ccm_node)
>  	hws[IMX7D_USB1_MAIN_480M_CLK] = imx_clk_hw_fixed_factor("pll_usb1_main_clk", "osc", 20, 1);
>  	hws[IMX7D_USB_MAIN_480M_CLK] = imx_clk_hw_fixed_factor("pll_usb_main_clk", "osc", 20, 1);
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_clks[i] = &hws[index]->clk;
> -	}
> -
> -
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(7);
>  
>  }
>  CLK_OF_DECLARE(imx7d, "fsl,imx7d-ccm", imx7d_clocks_init);
> diff --git a/drivers/clk/imx/clk-imx7ulp.c b/drivers/clk/imx/clk-imx7ulp.c
> index 634c0b6636b0..779e09105da7 100644
> --- a/drivers/clk/imx/clk-imx7ulp.c
> +++ b/drivers/clk/imx/clk-imx7ulp.c
> @@ -43,19 +43,6 @@ static const struct clk_div_table ulp_div_table[] = {
>  	{ /* sentinel */ },
>  };
>  
> -static const int pcc2_uart_clk_ids[] __initconst = {
> -	IMX7ULP_CLK_LPUART4,
> -	IMX7ULP_CLK_LPUART5,
> -};
> -
> -static const int pcc3_uart_clk_ids[] __initconst = {
> -	IMX7ULP_CLK_LPUART6,
> -	IMX7ULP_CLK_LPUART7,
> -};
> -
> -static struct clk **pcc2_uart_clks[ARRAY_SIZE(pcc2_uart_clk_ids) + 1] __initdata;
> -static struct clk **pcc3_uart_clks[ARRAY_SIZE(pcc3_uart_clk_ids) + 1] __initdata;
> -
>  static void __init imx7ulp_clk_scg1_init(struct device_node *np)
>  {
>  	struct clk_hw_onecell_data *clk_data;
> @@ -150,7 +137,6 @@ static void __init imx7ulp_clk_pcc2_init(struct device_node *np)
>  	struct clk_hw_onecell_data *clk_data;
>  	struct clk_hw **hws;
>  	void __iomem *base;
> -	int i;
>  
>  	clk_data = kzalloc(struct_size(clk_data, hws, IMX7ULP_CLK_PCC2_END),
>  			   GFP_KERNEL);
> @@ -190,13 +176,7 @@ static void __init imx7ulp_clk_pcc2_init(struct device_node *np)
>  
>  	of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_data);
>  
> -	for (i = 0; i < ARRAY_SIZE(pcc2_uart_clk_ids); i++) {
> -		int index = pcc2_uart_clk_ids[i];
> -
> -		pcc2_uart_clks[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(pcc2_uart_clks);
> +	imx_register_uart_clocks(2);
>  }
>  CLK_OF_DECLARE(imx7ulp_clk_pcc2, "fsl,imx7ulp-pcc2", imx7ulp_clk_pcc2_init);
>  
> @@ -205,7 +185,6 @@ static void __init imx7ulp_clk_pcc3_init(struct device_node *np)
>  	struct clk_hw_onecell_data *clk_data;
>  	struct clk_hw **hws;
>  	void __iomem *base;
> -	int i;
>  
>  	clk_data = kzalloc(struct_size(clk_data, hws, IMX7ULP_CLK_PCC3_END),
>  			   GFP_KERNEL);
> @@ -244,13 +223,7 @@ static void __init imx7ulp_clk_pcc3_init(struct device_node *np)
>  
>  	of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_data);
>  
> -	for (i = 0; i < ARRAY_SIZE(pcc3_uart_clk_ids); i++) {
> -		int index = pcc3_uart_clk_ids[i];
> -
> -		pcc3_uart_clks[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(pcc3_uart_clks);
> +	imx_register_uart_clocks(7);
>  }
>  CLK_OF_DECLARE(imx7ulp_clk_pcc3, "fsl,imx7ulp-pcc3", imx7ulp_clk_pcc3_init);
>  
> diff --git a/drivers/clk/imx/clk-imx8mm.c b/drivers/clk/imx/clk-imx8mm.c
> index 6a01eec36dd0..f1919fafb124 100644
> --- a/drivers/clk/imx/clk-imx8mm.c
> +++ b/drivers/clk/imx/clk-imx8mm.c
> @@ -296,20 +296,12 @@ static const char * const clkout_sels[] = {"audio_pll1_out", "audio_pll2_out", "
>  static struct clk_hw_onecell_data *clk_hw_data;
>  static struct clk_hw **hws;
>  
> -static const int uart_clk_ids[] = {
> -	IMX8MM_CLK_UART1_ROOT,
> -	IMX8MM_CLK_UART2_ROOT,
> -	IMX8MM_CLK_UART3_ROOT,
> -	IMX8MM_CLK_UART4_ROOT,
> -};
> -static struct clk **uart_hws[ARRAY_SIZE(uart_clk_ids) + 1];
> -
>  static int imx8mm_clocks_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
>  	struct device_node *np = dev->of_node;
>  	void __iomem *base;
> -	int ret, i;
> +	int ret;
>  
>  	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
>  					  IMX8MM_CLK_END), GFP_KERNEL);
> @@ -634,13 +626,7 @@ static int imx8mm_clocks_probe(struct platform_device *pdev)
>  		goto unregister_hws;
>  	}
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_hws[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(uart_hws);
> +	imx_register_uart_clocks(4);
>  
>  	return 0;
>  
> diff --git a/drivers/clk/imx/clk-imx8mn.c b/drivers/clk/imx/clk-imx8mn.c
> index 324c5fd0aa04..88f6630cd472 100644
> --- a/drivers/clk/imx/clk-imx8mn.c
> +++ b/drivers/clk/imx/clk-imx8mn.c
> @@ -289,20 +289,12 @@ static const char * const clkout_sels[] = {"audio_pll1_out", "audio_pll2_out", "
>  static struct clk_hw_onecell_data *clk_hw_data;
>  static struct clk_hw **hws;
>  
> -static const int uart_clk_ids[] = {
> -	IMX8MN_CLK_UART1_ROOT,
> -	IMX8MN_CLK_UART2_ROOT,
> -	IMX8MN_CLK_UART3_ROOT,
> -	IMX8MN_CLK_UART4_ROOT,
> -};
> -static struct clk **uart_hws[ARRAY_SIZE(uart_clk_ids) + 1];
> -
>  static int imx8mn_clocks_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
>  	struct device_node *np = dev->of_node;
>  	void __iomem *base;
> -	int ret, i;
> +	int ret;
>  
>  	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
>  					  IMX8MN_CLK_END), GFP_KERNEL);
> @@ -585,13 +577,7 @@ static int imx8mn_clocks_probe(struct platform_device *pdev)
>  		goto unregister_hws;
>  	}
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_hws[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(uart_hws);
> +	imx_register_uart_clocks(4);
>  
>  	return 0;
>  
> diff --git a/drivers/clk/imx/clk-imx8mp.c b/drivers/clk/imx/clk-imx8mp.c
> index 2f4e1d674e1c..3e6557e7d559 100644
> --- a/drivers/clk/imx/clk-imx8mp.c
> +++ b/drivers/clk/imx/clk-imx8mp.c
> @@ -414,20 +414,11 @@ static const char * const imx8mp_dram_core_sels[] = {"dram_pll_out", "dram_alt_r
>  static struct clk_hw **hws;
>  static struct clk_hw_onecell_data *clk_hw_data;
>  
> -static const int uart_clk_ids[] = {
> -	IMX8MP_CLK_UART1_ROOT,
> -	IMX8MP_CLK_UART2_ROOT,
> -	IMX8MP_CLK_UART3_ROOT,
> -	IMX8MP_CLK_UART4_ROOT,
> -};
> -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1];
> -
>  static int imx8mp_clocks_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
>  	struct device_node *np;
>  	void __iomem *anatop_base, *ccm_base;
> -	int i;
>  
>  	np = of_find_compatible_node(NULL, NULL, "fsl,imx8mp-anatop");
>  	anatop_base = of_iomap(np, 0);
> @@ -737,13 +728,7 @@ static int imx8mp_clocks_probe(struct platform_device *pdev)
>  
>  	of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_hw_data);
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_clks[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(uart_clks);
> +	imx_register_uart_clocks(4);
>  
>  	return 0;
>  }
> diff --git a/drivers/clk/imx/clk-imx8mq.c b/drivers/clk/imx/clk-imx8mq.c
> index 4dd4ae9d022b..3e1a10d3f55c 100644
> --- a/drivers/clk/imx/clk-imx8mq.c
> +++ b/drivers/clk/imx/clk-imx8mq.c
> @@ -281,20 +281,12 @@ static const char * const pllout_monitor_sels[] = {"osc_25m", "osc_27m", "dummy"
>  static struct clk_hw_onecell_data *clk_hw_data;
>  static struct clk_hw **hws;
>  
> -static const int uart_clk_ids[] = {
> -	IMX8MQ_CLK_UART1_ROOT,
> -	IMX8MQ_CLK_UART2_ROOT,
> -	IMX8MQ_CLK_UART3_ROOT,
> -	IMX8MQ_CLK_UART4_ROOT,
> -};
> -static struct clk **uart_hws[ARRAY_SIZE(uart_clk_ids) + 1];
> -
>  static int imx8mq_clocks_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
>  	struct device_node *np = dev->of_node;
>  	void __iomem *base;
> -	int err, i;
> +	int err;
>  
>  	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
>  					  IMX8MQ_CLK_END), GFP_KERNEL);
> @@ -629,13 +621,7 @@ static int imx8mq_clocks_probe(struct platform_device *pdev)
>  		goto unregister_hws;
>  	}
>  
> -	for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> -		int index = uart_clk_ids[i];
> -
> -		uart_hws[i] = &hws[index]->clk;
> -	}
> -
> -	imx_register_uart_clocks(uart_hws);
> +	imx_register_uart_clocks(4);
>  
>  	return 0;
>  
> diff --git a/drivers/clk/imx/clk.c b/drivers/clk/imx/clk.c
> index 47882c51cb85..35e41b9a4e34 100644
> --- a/drivers/clk/imx/clk.c
> +++ b/drivers/clk/imx/clk.c
> @@ -147,8 +147,10 @@ void imx_cscmr1_fixup(u32 *val)
>  }
>  
>  #ifndef MODULE
> -static int imx_keep_uart_clocks;
> -static struct clk ** const *imx_uart_clocks;
> +
> +static bool imx_keep_uart_clocks;
> +static int imx_enabled_uart_clocks;
> +static struct clk **imx_uart_clocks;
>  
>  static int __init imx_keep_uart_clocks_param(char *str)
>  {
> @@ -161,24 +163,45 @@ __setup_param("earlycon", imx_keep_uart_earlycon,
>  __setup_param("earlyprintk", imx_keep_uart_earlyprintk,
>  	      imx_keep_uart_clocks_param, 0);
>  
> -void imx_register_uart_clocks(struct clk ** const clks[])
> +void imx_register_uart_clocks(unsigned int clk_count)
>  {
> +	imx_enabled_uart_clocks = 0;
> +
> +/* i.MX boards use device trees now.  For build tests without CONFIG_OF, do nothing */
> +#ifdef CONFIG_OF
>  	if (imx_keep_uart_clocks) {
>  		int i;
>  
> -		imx_uart_clocks = clks;
> -		for (i = 0; imx_uart_clocks[i]; i++)
> -			clk_prepare_enable(*imx_uart_clocks[i]);
> +		imx_uart_clocks = kcalloc(clk_count, sizeof(struct clk *), GFP_KERNEL);
> +
> +		if (!of_stdout)
> +			return;
> +
> +		for (i = 0; i < clk_count; i++) {
> +			imx_uart_clocks[imx_enabled_uart_clocks] = of_clk_get(of_stdout, i);
> +
> +			/* Stop if there are no more of_stdout references */
> +			if (IS_ERR(imx_uart_clocks[imx_enabled_uart_clocks]))
> +				return;
> +
> +			/* Only enable the clock if it's not NULL */
> +			if (imx_uart_clocks[imx_enabled_uart_clocks])
> +				clk_prepare_enable(imx_uart_clocks[imx_enabled_uart_clocks++]);
> +		}
>  	}
> +#endif
>  }
>  
>  static int __init imx_clk_disable_uart(void)
>  {
> -	if (imx_keep_uart_clocks && imx_uart_clocks) {
> +	if (imx_keep_uart_clocks && imx_enabled_uart_clocks) {
>  		int i;
>  
> -		for (i = 0; imx_uart_clocks[i]; i++)
> -			clk_disable_unprepare(*imx_uart_clocks[i]);
> +		for (i = 0; i < imx_enabled_uart_clocks; i++) {
> +			clk_disable_unprepare(imx_uart_clocks[i]);
> +			clk_put(imx_uart_clocks[i]);
> +		};

Also removed the semicolon here and squashed into your change.

> +		kfree(imx_uart_clocks);
>  	}
>  
>  	return 0;
> diff --git a/drivers/clk/imx/clk.h b/drivers/clk/imx/clk.h
> index 4f04c8287286..7571603bee23 100644
> --- a/drivers/clk/imx/clk.h
> +++ b/drivers/clk/imx/clk.h
> @@ -11,9 +11,9 @@ extern spinlock_t imx_ccm_lock;
>  void imx_check_clocks(struct clk *clks[], unsigned int count);
>  void imx_check_clk_hws(struct clk_hw *clks[], unsigned int count);
>  #ifndef MODULE
> -void imx_register_uart_clocks(struct clk ** const clks[]);
> +void imx_register_uart_clocks(unsigned int clk_count);
>  #else
> -static inline void imx_register_uart_clocks(struct clk ** const clks[])
> +static inline void imx_register_uart_clocks(unsigned int clk_count)
>  {
>  }
>  #endif
> -- 
> 2.25.1
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH V4] clk: imx: Fix reparenting of UARTs not associated with stdout
  2021-03-22 21:42 ` Abel Vesa
@ 2021-03-24 17:06   ` Adam Ford
  0 siblings, 0 replies; 7+ messages in thread
From: Adam Ford @ 2021-03-24 17:06 UTC (permalink / raw)
  To: Abel Vesa
  Cc: linux-clk, Adam Ford-BE, Aisheng Dong, Ahmad Fatoum,
	Michael Turquette, Stephen Boyd, Shawn Guo, Sascha Hauer,
	Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
	Jerome Brunet, Linus Walleij, arm-soc, Linux Kernel Mailing List

On Mon, Mar 22, 2021 at 4:42 PM Abel Vesa <abel.vesa@nxp.com> wrote:
>
> On 21-03-13 06:28:17, Adam Ford wrote:
> > Most if not all i.MX SoC's call a function which enables all UARTS.
> > This is a problem for users who need to re-parent the clock source,
> > because any attempt to change the parent results in an busy error
> > due to the fact that the clocks have been enabled already.
> >
> >   clk: failed to reparent uart1 to sys_pll1_80m: -16
> >
> > Instead of pre-initializing all UARTS, scan the device tree to see
> > which UART clocks are associated to stdout, and only enable those
> > UART clocks if it's needed early.  This will move initialization of
> > the remaining clocks until after the parenting of the clocks.
> >
> > When the clocks are shutdown, this mechanism will also disable any
> > clocks that were pre-initialized.
> >
> > Fixes: 9461f7b33d11c ("clk: fix CLK_SET_RATE_GATE with clock rate protection")
> > Suggested-by: Aisheng Dong <aisheng.dong@nxp.com>
> > Signed-off-by: Adam Ford <aford173@gmail.com>
> > Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
> > Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
> >
> > ---
> > V4:  Check if of_stdout is available before using it.
> >      Re-align #ifdef to remove repeated code.
> > V3:  Return a method more closely related to upstream kernel but
> >      instead of passing an array of UART's, each SoC passes the max
> >      number of UART clocks is has.  The imx clock driver will create
> >      an array to enable on startup, and disable later.
> > V2:  Attempt to port driver from vendor kernel.
> > ---
> >  drivers/clk/imx/clk-imx25.c   | 12 +---------
> >  drivers/clk/imx/clk-imx27.c   | 13 +----------
> >  drivers/clk/imx/clk-imx35.c   | 10 +--------
> >  drivers/clk/imx/clk-imx5.c    | 30 +++----------------------
> >  drivers/clk/imx/clk-imx6q.c   | 16 +-------------
> >  drivers/clk/imx/clk-imx6sl.c  | 16 +-------------
> >  drivers/clk/imx/clk-imx6sll.c | 24 +-------------------
> >  drivers/clk/imx/clk-imx6sx.c  | 16 +-------------
> >  drivers/clk/imx/clk-imx7d.c   | 22 +------------------
> >  drivers/clk/imx/clk-imx7ulp.c | 31 ++------------------------
> >  drivers/clk/imx/clk-imx8mm.c  | 18 ++-------------
> >  drivers/clk/imx/clk-imx8mn.c  | 18 ++-------------
> >  drivers/clk/imx/clk-imx8mp.c  | 17 +--------------
> >  drivers/clk/imx/clk-imx8mq.c  | 18 ++-------------
> >  drivers/clk/imx/clk.c         | 41 +++++++++++++++++++++++++++--------
> >  drivers/clk/imx/clk.h         |  4 ++--
> >  16 files changed, 54 insertions(+), 252 deletions(-)
> >
> > diff --git a/drivers/clk/imx/clk-imx25.c b/drivers/clk/imx/clk-imx25.c
> > index a66cabfbf94f..66192fe0a898 100644
> > --- a/drivers/clk/imx/clk-imx25.c
> > +++ b/drivers/clk/imx/clk-imx25.c
> > @@ -73,16 +73,6 @@ enum mx25_clks {
> >
> >  static struct clk *clk[clk_max];
> >
> > -static struct clk ** const uart_clks[] __initconst = {
> > -     &clk[uart_ipg_per],
> > -     &clk[uart1_ipg],
> > -     &clk[uart2_ipg],
> > -     &clk[uart3_ipg],
> > -     &clk[uart4_ipg],
> > -     &clk[uart5_ipg],
> > -     NULL
> > -};
> > -
> >  static int __init __mx25_clocks_init(void __iomem *ccm_base)
> >  {
> >       BUG_ON(!ccm_base);
> > @@ -228,7 +218,7 @@ static int __init __mx25_clocks_init(void __iomem *ccm_base)
> >        */
> >       clk_set_parent(clk[cko_sel], clk[ipg]);
> >
> > -     imx_register_uart_clocks(uart_clks);
> > +     imx_register_uart_clocks(6);
> >
> >       return 0;
> >  }
> > diff --git a/drivers/clk/imx/clk-imx27.c b/drivers/clk/imx/clk-imx27.c
> > index 5585ded8b8c6..56a5fc402b10 100644
> > --- a/drivers/clk/imx/clk-imx27.c
> > +++ b/drivers/clk/imx/clk-imx27.c
> > @@ -49,17 +49,6 @@ static const char *ssi_sel_clks[] = { "spll_gate", "mpll", };
> >  static struct clk *clk[IMX27_CLK_MAX];
> >  static struct clk_onecell_data clk_data;
> >
> > -static struct clk ** const uart_clks[] __initconst = {
> > -     &clk[IMX27_CLK_PER1_GATE],
> > -     &clk[IMX27_CLK_UART1_IPG_GATE],
> > -     &clk[IMX27_CLK_UART2_IPG_GATE],
> > -     &clk[IMX27_CLK_UART3_IPG_GATE],
> > -     &clk[IMX27_CLK_UART4_IPG_GATE],
> > -     &clk[IMX27_CLK_UART5_IPG_GATE],
> > -     &clk[IMX27_CLK_UART6_IPG_GATE],
> > -     NULL
> > -};
> > -
> >  static void __init _mx27_clocks_init(unsigned long fref)
> >  {
> >       BUG_ON(!ccm);
> > @@ -176,7 +165,7 @@ static void __init _mx27_clocks_init(unsigned long fref)
> >
> >       clk_prepare_enable(clk[IMX27_CLK_EMI_AHB_GATE]);
> >
> > -     imx_register_uart_clocks(uart_clks);
> > +     imx_register_uart_clocks(7);
> >
> >       imx_print_silicon_rev("i.MX27", mx27_revision());
> >  }
> > diff --git a/drivers/clk/imx/clk-imx35.c b/drivers/clk/imx/clk-imx35.c
> > index c1df03665c09..0fe5ac210156 100644
> > --- a/drivers/clk/imx/clk-imx35.c
> > +++ b/drivers/clk/imx/clk-imx35.c
> > @@ -82,14 +82,6 @@ enum mx35_clks {
> >
> >  static struct clk *clk[clk_max];
> >
> > -static struct clk ** const uart_clks[] __initconst = {
> > -     &clk[ipg],
> > -     &clk[uart1_gate],
> > -     &clk[uart2_gate],
> > -     &clk[uart3_gate],
> > -     NULL
> > -};
> > -
> >  static void __init _mx35_clocks_init(void)
> >  {
> >       void __iomem *base;
> > @@ -243,7 +235,7 @@ static void __init _mx35_clocks_init(void)
> >        */
> >       clk_prepare_enable(clk[scc_gate]);
> >
> > -     imx_register_uart_clocks(uart_clks);
> > +     imx_register_uart_clocks(4);
> >
> >       imx_print_silicon_rev("i.MX35", mx35_revision());
> >  }
> > diff --git a/drivers/clk/imx/clk-imx5.c b/drivers/clk/imx/clk-imx5.c
> > index 01e079b81026..e4493846454d 100644
> > --- a/drivers/clk/imx/clk-imx5.c
> > +++ b/drivers/clk/imx/clk-imx5.c
> > @@ -128,30 +128,6 @@ static const char *ieee1588_sels[] = { "pll3_sw", "pll4_sw", "dummy" /* usbphy2_
> >  static struct clk *clk[IMX5_CLK_END];
> >  static struct clk_onecell_data clk_data;
> >
> > -static struct clk ** const uart_clks_mx51[] __initconst = {
> > -     &clk[IMX5_CLK_UART1_IPG_GATE],
> > -     &clk[IMX5_CLK_UART1_PER_GATE],
> > -     &clk[IMX5_CLK_UART2_IPG_GATE],
> > -     &clk[IMX5_CLK_UART2_PER_GATE],
> > -     &clk[IMX5_CLK_UART3_IPG_GATE],
> > -     &clk[IMX5_CLK_UART3_PER_GATE],
> > -     NULL
> > -};
> > -
> > -static struct clk ** const uart_clks_mx50_mx53[] __initconst = {
> > -     &clk[IMX5_CLK_UART1_IPG_GATE],
> > -     &clk[IMX5_CLK_UART1_PER_GATE],
> > -     &clk[IMX5_CLK_UART2_IPG_GATE],
> > -     &clk[IMX5_CLK_UART2_PER_GATE],
> > -     &clk[IMX5_CLK_UART3_IPG_GATE],
> > -     &clk[IMX5_CLK_UART3_PER_GATE],
> > -     &clk[IMX5_CLK_UART4_IPG_GATE],
> > -     &clk[IMX5_CLK_UART4_PER_GATE],
> > -     &clk[IMX5_CLK_UART5_IPG_GATE],
> > -     &clk[IMX5_CLK_UART5_PER_GATE],
> > -     NULL
> > -};
> > -
> >  static void __init mx5_clocks_common_init(void __iomem *ccm_base)
> >  {
> >       clk[IMX5_CLK_DUMMY]             = imx_clk_fixed("dummy", 0);
> > @@ -382,7 +358,7 @@ static void __init mx50_clocks_init(struct device_node *np)
> >       r = clk_round_rate(clk[IMX5_CLK_USBOH3_PER_GATE], 54000000);
> >       clk_set_rate(clk[IMX5_CLK_USBOH3_PER_GATE], r);
> >
> > -     imx_register_uart_clocks(uart_clks_mx50_mx53);
> > +     imx_register_uart_clocks(5);
> >  }
> >  CLK_OF_DECLARE(imx50_ccm, "fsl,imx50-ccm", mx50_clocks_init);
> >
> > @@ -488,7 +464,7 @@ static void __init mx51_clocks_init(struct device_node *np)
> >       val |= 1 << 23;
> >       writel(val, MXC_CCM_CLPCR);
> >
> > -     imx_register_uart_clocks(uart_clks_mx51);
> > +     imx_register_uart_clocks(3);
> >  }
> >  CLK_OF_DECLARE(imx51_ccm, "fsl,imx51-ccm", mx51_clocks_init);
> >
> > @@ -633,6 +609,6 @@ static void __init mx53_clocks_init(struct device_node *np)
> >       r = clk_round_rate(clk[IMX5_CLK_USBOH3_PER_GATE], 54000000);
> >       clk_set_rate(clk[IMX5_CLK_USBOH3_PER_GATE], r);
> >
> > -     imx_register_uart_clocks(uart_clks_mx50_mx53);
> > +     imx_register_uart_clocks(5);
> >  }
> >  CLK_OF_DECLARE(imx53_ccm, "fsl,imx53-ccm", mx53_clocks_init);
> > diff --git a/drivers/clk/imx/clk-imx6q.c b/drivers/clk/imx/clk-imx6q.c
> > index 521d6136d22c..496900de0b0b 100644
> > --- a/drivers/clk/imx/clk-imx6q.c
> > +++ b/drivers/clk/imx/clk-imx6q.c
> > @@ -140,13 +140,6 @@ static inline int clk_on_imx6dl(void)
> >       return of_machine_is_compatible("fsl,imx6dl");
> >  }
> >
> > -static const int uart_clk_ids[] __initconst = {
> > -     IMX6QDL_CLK_UART_IPG,
> > -     IMX6QDL_CLK_UART_SERIAL,
> > -};
> > -
> > -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
> > -
> >  static int ldb_di_sel_by_clock_id(int clock_id)
> >  {
> >       switch (clock_id) {
> > @@ -440,7 +433,6 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
> >       struct device_node *np;
> >       void __iomem *anatop_base, *base;
> >       int ret;
> > -     int i;
> >
> >       clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
> >                                         IMX6QDL_CLK_END), GFP_KERNEL);
> > @@ -982,12 +974,6 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
> >                              hws[IMX6QDL_CLK_PLL3_USB_OTG]->clk);
> >       }
> >
> > -     for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> > -             int index = uart_clk_ids[i];
> > -
> > -             uart_clks[i] = &hws[index]->clk;
> > -     }
> > -
> > -     imx_register_uart_clocks(uart_clks);
> > +     imx_register_uart_clocks(1);
> >  }
> >  CLK_OF_DECLARE(imx6q, "fsl,imx6q-ccm", imx6q_clocks_init);
> > diff --git a/drivers/clk/imx/clk-imx6sl.c b/drivers/clk/imx/clk-imx6sl.c
> > index 29eab05c9068..277365970320 100644
> > --- a/drivers/clk/imx/clk-imx6sl.c
> > +++ b/drivers/clk/imx/clk-imx6sl.c
> > @@ -179,19 +179,11 @@ void imx6sl_set_wait_clk(bool enter)
> >               imx6sl_enable_pll_arm(false);
> >  }
> >
> > -static const int uart_clk_ids[] __initconst = {
> > -     IMX6SL_CLK_UART,
> > -     IMX6SL_CLK_UART_SERIAL,
> > -};
> > -
> > -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
> > -
> >  static void __init imx6sl_clocks_init(struct device_node *ccm_node)
> >  {
> >       struct device_node *np;
> >       void __iomem *base;
> >       int ret;
> > -     int i;
> >
> >       clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
> >                                         IMX6SL_CLK_END), GFP_KERNEL);
> > @@ -448,12 +440,6 @@ static void __init imx6sl_clocks_init(struct device_node *ccm_node)
> >       clk_set_parent(hws[IMX6SL_CLK_LCDIF_AXI_SEL]->clk,
> >                      hws[IMX6SL_CLK_PLL2_PFD2]->clk);
> >
> > -     for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> > -             int index = uart_clk_ids[i];
> > -
> > -             uart_clks[i] = &hws[index]->clk;
> > -     }
> > -
> > -     imx_register_uart_clocks(uart_clks);
> > +     imx_register_uart_clocks(2);
> >  }
> >  CLK_OF_DECLARE(imx6sl, "fsl,imx6sl-ccm", imx6sl_clocks_init);
> > diff --git a/drivers/clk/imx/clk-imx6sll.c b/drivers/clk/imx/clk-imx6sll.c
> > index 8e8288bda4d0..31d777f30039 100644
> > --- a/drivers/clk/imx/clk-imx6sll.c
> > +++ b/drivers/clk/imx/clk-imx6sll.c
> > @@ -76,26 +76,10 @@ static u32 share_count_ssi1;
> >  static u32 share_count_ssi2;
> >  static u32 share_count_ssi3;
> >
> > -static const int uart_clk_ids[] __initconst = {
> > -     IMX6SLL_CLK_UART1_IPG,
> > -     IMX6SLL_CLK_UART1_SERIAL,
> > -     IMX6SLL_CLK_UART2_IPG,
> > -     IMX6SLL_CLK_UART2_SERIAL,
> > -     IMX6SLL_CLK_UART3_IPG,
> > -     IMX6SLL_CLK_UART3_SERIAL,
> > -     IMX6SLL_CLK_UART4_IPG,
> > -     IMX6SLL_CLK_UART4_SERIAL,
> > -     IMX6SLL_CLK_UART5_IPG,
> > -     IMX6SLL_CLK_UART5_SERIAL,
> > -};
> > -
> > -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
> > -
> >  static void __init imx6sll_clocks_init(struct device_node *ccm_node)
> >  {
> >       struct device_node *np;
> >       void __iomem *base;
> > -     int i;
> >
> >       clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
> >                                         IMX6SLL_CLK_END), GFP_KERNEL);
> > @@ -356,13 +340,7 @@ static void __init imx6sll_clocks_init(struct device_node *ccm_node)
> >
> >       of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_hw_data);
> >
> > -     for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> > -             int index = uart_clk_ids[i];
> > -
> > -             uart_clks[i] = &hws[index]->clk;
> > -     }
> > -
> > -     imx_register_uart_clocks(uart_clks);
> > +     imx_register_uart_clocks(5);
> >
> >       /* Lower the AHB clock rate before changing the clock source. */
> >       clk_set_rate(hws[IMX6SLL_CLK_AHB]->clk, 99000000);
> > diff --git a/drivers/clk/imx/clk-imx6sx.c b/drivers/clk/imx/clk-imx6sx.c
> > index 20dcce526d07..fc1bd23d4583 100644
> > --- a/drivers/clk/imx/clk-imx6sx.c
> > +++ b/drivers/clk/imx/clk-imx6sx.c
> > @@ -117,18 +117,10 @@ static u32 share_count_ssi3;
> >  static u32 share_count_sai1;
> >  static u32 share_count_sai2;
> >
> > -static const int uart_clk_ids[] __initconst = {
> > -     IMX6SX_CLK_UART_IPG,
> > -     IMX6SX_CLK_UART_SERIAL,
> > -};
> > -
> > -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
> > -
> >  static void __init imx6sx_clocks_init(struct device_node *ccm_node)
> >  {
> >       struct device_node *np;
> >       void __iomem *base;
> > -     int i;
> >
> >       clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
> >                                         IMX6SX_CLK_CLK_END), GFP_KERNEL);
> > @@ -556,12 +548,6 @@ static void __init imx6sx_clocks_init(struct device_node *ccm_node)
> >       clk_set_parent(hws[IMX6SX_CLK_QSPI1_SEL]->clk, hws[IMX6SX_CLK_PLL2_BUS]->clk);
> >       clk_set_parent(hws[IMX6SX_CLK_QSPI2_SEL]->clk, hws[IMX6SX_CLK_PLL2_BUS]->clk);
> >
> > -     for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> > -             int index = uart_clk_ids[i];
> > -
> > -             uart_clks[i] = &hws[index]->clk;
> > -     }
> > -
> > -     imx_register_uart_clocks(uart_clks);
> > +     imx_register_uart_clocks(2);
> >  }
> >  CLK_OF_DECLARE(imx6sx, "fsl,imx6sx-ccm", imx6sx_clocks_init);
> > diff --git a/drivers/clk/imx/clk-imx7d.c b/drivers/clk/imx/clk-imx7d.c
> > index 22d24a6a05e7..c4e0f1c07192 100644
> > --- a/drivers/clk/imx/clk-imx7d.c
> > +++ b/drivers/clk/imx/clk-imx7d.c
> > @@ -377,23 +377,10 @@ static const char *pll_video_bypass_sel[] = { "pll_video_main", "pll_video_main_
> >  static struct clk_hw **hws;
> >  static struct clk_hw_onecell_data *clk_hw_data;
> >
> > -static const int uart_clk_ids[] __initconst = {
> > -     IMX7D_UART1_ROOT_CLK,
> > -     IMX7D_UART2_ROOT_CLK,
> > -     IMX7D_UART3_ROOT_CLK,
> > -     IMX7D_UART4_ROOT_CLK,
> > -     IMX7D_UART5_ROOT_CLK,
> > -     IMX7D_UART6_ROOT_CLK,
> > -     IMX7D_UART7_ROOT_CLK,
> > -};
> > -
> > -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1] __initdata;
> > -
> >  static void __init imx7d_clocks_init(struct device_node *ccm_node)
> >  {
> >       struct device_node *np;
> >       void __iomem *base;
> > -     int i;
> >
> >       clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
> >                                         IMX7D_CLK_END), GFP_KERNEL);
> > @@ -897,14 +884,7 @@ static void __init imx7d_clocks_init(struct device_node *ccm_node)
> >       hws[IMX7D_USB1_MAIN_480M_CLK] = imx_clk_hw_fixed_factor("pll_usb1_main_clk", "osc", 20, 1);
> >       hws[IMX7D_USB_MAIN_480M_CLK] = imx_clk_hw_fixed_factor("pll_usb_main_clk", "osc", 20, 1);
> >
> > -     for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> > -             int index = uart_clk_ids[i];
> > -
> > -             uart_clks[i] = &hws[index]->clk;
> > -     }
> > -
> > -
> > -     imx_register_uart_clocks(uart_clks);
> > +     imx_register_uart_clocks(7);
> >
> >  }
> >  CLK_OF_DECLARE(imx7d, "fsl,imx7d-ccm", imx7d_clocks_init);
> > diff --git a/drivers/clk/imx/clk-imx7ulp.c b/drivers/clk/imx/clk-imx7ulp.c
> > index 634c0b6636b0..779e09105da7 100644
> > --- a/drivers/clk/imx/clk-imx7ulp.c
> > +++ b/drivers/clk/imx/clk-imx7ulp.c
> > @@ -43,19 +43,6 @@ static const struct clk_div_table ulp_div_table[] = {
> >       { /* sentinel */ },
> >  };
> >
> > -static const int pcc2_uart_clk_ids[] __initconst = {
> > -     IMX7ULP_CLK_LPUART4,
> > -     IMX7ULP_CLK_LPUART5,
> > -};
> > -
> > -static const int pcc3_uart_clk_ids[] __initconst = {
> > -     IMX7ULP_CLK_LPUART6,
> > -     IMX7ULP_CLK_LPUART7,
> > -};
> > -
> > -static struct clk **pcc2_uart_clks[ARRAY_SIZE(pcc2_uart_clk_ids) + 1] __initdata;
> > -static struct clk **pcc3_uart_clks[ARRAY_SIZE(pcc3_uart_clk_ids) + 1] __initdata;
> > -
> >  static void __init imx7ulp_clk_scg1_init(struct device_node *np)
> >  {
> >       struct clk_hw_onecell_data *clk_data;
> > @@ -150,7 +137,6 @@ static void __init imx7ulp_clk_pcc2_init(struct device_node *np)
> >       struct clk_hw_onecell_data *clk_data;
> >       struct clk_hw **hws;
> >       void __iomem *base;
> > -     int i;
> >
> >       clk_data = kzalloc(struct_size(clk_data, hws, IMX7ULP_CLK_PCC2_END),
> >                          GFP_KERNEL);
> > @@ -190,13 +176,7 @@ static void __init imx7ulp_clk_pcc2_init(struct device_node *np)
> >
> >       of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_data);
> >
> > -     for (i = 0; i < ARRAY_SIZE(pcc2_uart_clk_ids); i++) {
> > -             int index = pcc2_uart_clk_ids[i];
> > -
> > -             pcc2_uart_clks[i] = &hws[index]->clk;
> > -     }
> > -
> > -     imx_register_uart_clocks(pcc2_uart_clks);
> > +     imx_register_uart_clocks(2);
> >  }
> >  CLK_OF_DECLARE(imx7ulp_clk_pcc2, "fsl,imx7ulp-pcc2", imx7ulp_clk_pcc2_init);
> >
> > @@ -205,7 +185,6 @@ static void __init imx7ulp_clk_pcc3_init(struct device_node *np)
> >       struct clk_hw_onecell_data *clk_data;
> >       struct clk_hw **hws;
> >       void __iomem *base;
> > -     int i;
> >
> >       clk_data = kzalloc(struct_size(clk_data, hws, IMX7ULP_CLK_PCC3_END),
> >                          GFP_KERNEL);
> > @@ -244,13 +223,7 @@ static void __init imx7ulp_clk_pcc3_init(struct device_node *np)
> >
> >       of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_data);
> >
> > -     for (i = 0; i < ARRAY_SIZE(pcc3_uart_clk_ids); i++) {
> > -             int index = pcc3_uart_clk_ids[i];
> > -
> > -             pcc3_uart_clks[i] = &hws[index]->clk;
> > -     }
> > -
> > -     imx_register_uart_clocks(pcc3_uart_clks);
> > +     imx_register_uart_clocks(7);
> >  }
> >  CLK_OF_DECLARE(imx7ulp_clk_pcc3, "fsl,imx7ulp-pcc3", imx7ulp_clk_pcc3_init);
> >
> > diff --git a/drivers/clk/imx/clk-imx8mm.c b/drivers/clk/imx/clk-imx8mm.c
> > index 6a01eec36dd0..f1919fafb124 100644
> > --- a/drivers/clk/imx/clk-imx8mm.c
> > +++ b/drivers/clk/imx/clk-imx8mm.c
> > @@ -296,20 +296,12 @@ static const char * const clkout_sels[] = {"audio_pll1_out", "audio_pll2_out", "
> >  static struct clk_hw_onecell_data *clk_hw_data;
> >  static struct clk_hw **hws;
> >
> > -static const int uart_clk_ids[] = {
> > -     IMX8MM_CLK_UART1_ROOT,
> > -     IMX8MM_CLK_UART2_ROOT,
> > -     IMX8MM_CLK_UART3_ROOT,
> > -     IMX8MM_CLK_UART4_ROOT,
> > -};
> > -static struct clk **uart_hws[ARRAY_SIZE(uart_clk_ids) + 1];
> > -
> >  static int imx8mm_clocks_probe(struct platform_device *pdev)
> >  {
> >       struct device *dev = &pdev->dev;
> >       struct device_node *np = dev->of_node;
> >       void __iomem *base;
> > -     int ret, i;
> > +     int ret;
> >
> >       clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
> >                                         IMX8MM_CLK_END), GFP_KERNEL);
> > @@ -634,13 +626,7 @@ static int imx8mm_clocks_probe(struct platform_device *pdev)
> >               goto unregister_hws;
> >       }
> >
> > -     for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> > -             int index = uart_clk_ids[i];
> > -
> > -             uart_hws[i] = &hws[index]->clk;
> > -     }
> > -
> > -     imx_register_uart_clocks(uart_hws);
> > +     imx_register_uart_clocks(4);
> >
> >       return 0;
> >
> > diff --git a/drivers/clk/imx/clk-imx8mn.c b/drivers/clk/imx/clk-imx8mn.c
> > index 324c5fd0aa04..88f6630cd472 100644
> > --- a/drivers/clk/imx/clk-imx8mn.c
> > +++ b/drivers/clk/imx/clk-imx8mn.c
> > @@ -289,20 +289,12 @@ static const char * const clkout_sels[] = {"audio_pll1_out", "audio_pll2_out", "
> >  static struct clk_hw_onecell_data *clk_hw_data;
> >  static struct clk_hw **hws;
> >
> > -static const int uart_clk_ids[] = {
> > -     IMX8MN_CLK_UART1_ROOT,
> > -     IMX8MN_CLK_UART2_ROOT,
> > -     IMX8MN_CLK_UART3_ROOT,
> > -     IMX8MN_CLK_UART4_ROOT,
> > -};
> > -static struct clk **uart_hws[ARRAY_SIZE(uart_clk_ids) + 1];
> > -
> >  static int imx8mn_clocks_probe(struct platform_device *pdev)
> >  {
> >       struct device *dev = &pdev->dev;
> >       struct device_node *np = dev->of_node;
> >       void __iomem *base;
> > -     int ret, i;
> > +     int ret;
> >
> >       clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
> >                                         IMX8MN_CLK_END), GFP_KERNEL);
> > @@ -585,13 +577,7 @@ static int imx8mn_clocks_probe(struct platform_device *pdev)
> >               goto unregister_hws;
> >       }
> >
> > -     for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> > -             int index = uart_clk_ids[i];
> > -
> > -             uart_hws[i] = &hws[index]->clk;
> > -     }
> > -
> > -     imx_register_uart_clocks(uart_hws);
> > +     imx_register_uart_clocks(4);
> >
> >       return 0;
> >
> > diff --git a/drivers/clk/imx/clk-imx8mp.c b/drivers/clk/imx/clk-imx8mp.c
> > index 2f4e1d674e1c..3e6557e7d559 100644
> > --- a/drivers/clk/imx/clk-imx8mp.c
> > +++ b/drivers/clk/imx/clk-imx8mp.c
> > @@ -414,20 +414,11 @@ static const char * const imx8mp_dram_core_sels[] = {"dram_pll_out", "dram_alt_r
> >  static struct clk_hw **hws;
> >  static struct clk_hw_onecell_data *clk_hw_data;
> >
> > -static const int uart_clk_ids[] = {
> > -     IMX8MP_CLK_UART1_ROOT,
> > -     IMX8MP_CLK_UART2_ROOT,
> > -     IMX8MP_CLK_UART3_ROOT,
> > -     IMX8MP_CLK_UART4_ROOT,
> > -};
> > -static struct clk **uart_clks[ARRAY_SIZE(uart_clk_ids) + 1];
> > -
> >  static int imx8mp_clocks_probe(struct platform_device *pdev)
> >  {
> >       struct device *dev = &pdev->dev;
> >       struct device_node *np;
> >       void __iomem *anatop_base, *ccm_base;
> > -     int i;
> >
> >       np = of_find_compatible_node(NULL, NULL, "fsl,imx8mp-anatop");
> >       anatop_base = of_iomap(np, 0);
> > @@ -737,13 +728,7 @@ static int imx8mp_clocks_probe(struct platform_device *pdev)
> >
> >       of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_hw_data);
> >
> > -     for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> > -             int index = uart_clk_ids[i];
> > -
> > -             uart_clks[i] = &hws[index]->clk;
> > -     }
> > -
> > -     imx_register_uart_clocks(uart_clks);
> > +     imx_register_uart_clocks(4);
> >
> >       return 0;
> >  }
> > diff --git a/drivers/clk/imx/clk-imx8mq.c b/drivers/clk/imx/clk-imx8mq.c
> > index 4dd4ae9d022b..3e1a10d3f55c 100644
> > --- a/drivers/clk/imx/clk-imx8mq.c
> > +++ b/drivers/clk/imx/clk-imx8mq.c
> > @@ -281,20 +281,12 @@ static const char * const pllout_monitor_sels[] = {"osc_25m", "osc_27m", "dummy"
> >  static struct clk_hw_onecell_data *clk_hw_data;
> >  static struct clk_hw **hws;
> >
> > -static const int uart_clk_ids[] = {
> > -     IMX8MQ_CLK_UART1_ROOT,
> > -     IMX8MQ_CLK_UART2_ROOT,
> > -     IMX8MQ_CLK_UART3_ROOT,
> > -     IMX8MQ_CLK_UART4_ROOT,
> > -};
> > -static struct clk **uart_hws[ARRAY_SIZE(uart_clk_ids) + 1];
> > -
> >  static int imx8mq_clocks_probe(struct platform_device *pdev)
> >  {
> >       struct device *dev = &pdev->dev;
> >       struct device_node *np = dev->of_node;
> >       void __iomem *base;
> > -     int err, i;
> > +     int err;
> >
> >       clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
> >                                         IMX8MQ_CLK_END), GFP_KERNEL);
> > @@ -629,13 +621,7 @@ static int imx8mq_clocks_probe(struct platform_device *pdev)
> >               goto unregister_hws;
> >       }
> >
> > -     for (i = 0; i < ARRAY_SIZE(uart_clk_ids); i++) {
> > -             int index = uart_clk_ids[i];
> > -
> > -             uart_hws[i] = &hws[index]->clk;
> > -     }
> > -
> > -     imx_register_uart_clocks(uart_hws);
> > +     imx_register_uart_clocks(4);
> >
> >       return 0;
> >
> > diff --git a/drivers/clk/imx/clk.c b/drivers/clk/imx/clk.c
> > index 47882c51cb85..35e41b9a4e34 100644
> > --- a/drivers/clk/imx/clk.c
> > +++ b/drivers/clk/imx/clk.c
> > @@ -147,8 +147,10 @@ void imx_cscmr1_fixup(u32 *val)
> >  }
> >
> >  #ifndef MODULE
> > -static int imx_keep_uart_clocks;
> > -static struct clk ** const *imx_uart_clocks;
> > +
> > +static bool imx_keep_uart_clocks;
> > +static int imx_enabled_uart_clocks;
> > +static struct clk **imx_uart_clocks;
> >
> >  static int __init imx_keep_uart_clocks_param(char *str)
> >  {
> > @@ -161,24 +163,45 @@ __setup_param("earlycon", imx_keep_uart_earlycon,
> >  __setup_param("earlyprintk", imx_keep_uart_earlyprintk,
> >             imx_keep_uart_clocks_param, 0);
> >
> > -void imx_register_uart_clocks(struct clk ** const clks[])
> > +void imx_register_uart_clocks(unsigned int clk_count)
> >  {
> > +     imx_enabled_uart_clocks = 0;
> > +
> > +/* i.MX boards use device trees now.  For build tests without CONFIG_OF, do nothing */
> > +#ifdef CONFIG_OF
> >       if (imx_keep_uart_clocks) {
> >               int i;
> >
> > -             imx_uart_clocks = clks;
> > -             for (i = 0; imx_uart_clocks[i]; i++)
> > -                     clk_prepare_enable(*imx_uart_clocks[i]);
> > +             imx_uart_clocks = kcalloc(clk_count, sizeof(struct clk *), GFP_KERNEL);
> > +
> > +             if (!of_stdout)
> > +                     return;
> > +
> > +             for (i = 0; i < clk_count; i++) {
> > +                     imx_uart_clocks[imx_enabled_uart_clocks] = of_clk_get(of_stdout, i);
> > +
> > +                     /* Stop if there are no more of_stdout references */
> > +                     if (IS_ERR(imx_uart_clocks[imx_enabled_uart_clocks]))
> > +                             return;
> > +
> > +                     /* Only enable the clock if it's not NULL */
> > +                     if (imx_uart_clocks[imx_enabled_uart_clocks])
> > +                             clk_prepare_enable(imx_uart_clocks[imx_enabled_uart_clocks++]);
> > +             }
> >       }
> > +#endif
> >  }
> >
> >  static int __init imx_clk_disable_uart(void)
> >  {
> > -     if (imx_keep_uart_clocks && imx_uart_clocks) {
> > +     if (imx_keep_uart_clocks && imx_enabled_uart_clocks) {
> >               int i;
> >
> > -             for (i = 0; imx_uart_clocks[i]; i++)
> > -                     clk_disable_unprepare(*imx_uart_clocks[i]);
> > +             for (i = 0; i < imx_enabled_uart_clocks; i++) {
> > +                     clk_disable_unprepare(imx_uart_clocks[i]);
> > +                     clk_put(imx_uart_clocks[i]);
> > +             };
>
> Also removed the semicolon here and squashed into your change.

Thanks for doing that.  Sorry to make you have to do that.

adam
>
> > +             kfree(imx_uart_clocks);
> >       }
> >
> >       return 0;
> > diff --git a/drivers/clk/imx/clk.h b/drivers/clk/imx/clk.h
> > index 4f04c8287286..7571603bee23 100644
> > --- a/drivers/clk/imx/clk.h
> > +++ b/drivers/clk/imx/clk.h
> > @@ -11,9 +11,9 @@ extern spinlock_t imx_ccm_lock;
> >  void imx_check_clocks(struct clk *clks[], unsigned int count);
> >  void imx_check_clk_hws(struct clk_hw *clks[], unsigned int count);
> >  #ifndef MODULE
> > -void imx_register_uart_clocks(struct clk ** const clks[]);
> > +void imx_register_uart_clocks(unsigned int clk_count);
> >  #else
> > -static inline void imx_register_uart_clocks(struct clk ** const clks[])
> > +static inline void imx_register_uart_clocks(unsigned int clk_count)
> >  {
> >  }
> >  #endif
> > --
> > 2.25.1
> >

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 7+ messages in thread

end of thread, other threads:[~2021-03-24 17:08 UTC | newest]

Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-03-13 12:28 [PATCH V4] clk: imx: Fix reparenting of UARTs not associated with stdout Adam Ford
2021-03-13 15:16 ` Ahmad Fatoum
2021-03-14  9:40   ` Ahmad Fatoum
2021-03-20 23:00     ` Adam Ford
2021-03-22 11:05       ` Abel Vesa
2021-03-22 21:42 ` Abel Vesa
2021-03-24 17:06   ` Adam Ford

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).