* [PATCH v3] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
@ 2019-12-24 9:59 Rakesh Pillai
2019-12-29 3:14 ` Bjorn Andersson
0 siblings, 1 reply; 3+ messages in thread
From: Rakesh Pillai @ 2019-12-24 9:59 UTC (permalink / raw)
To: devicetree; +Cc: linux-arm-msm, Rakesh Pillai, linux-kernel, linux-arm-kernel
Add device node for the ath10k SNOC platform driver probe
and add resources required for WCN3990 on sc7180 soc.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
---
This change is dependent on the below set of changes
arm64: dts: sc7180: Add qupv3_0 and qupv3_1 (https://lore.kernel.org/patchwork/patch/1150367/)
---
arch/arm64/boot/dts/qcom/sc7180-idp.dts | 5 +++++
arch/arm64/boot/dts/qcom/sc7180.dtsi | 28 ++++++++++++++++++++++++++++
2 files changed, 33 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index 189254f..b2ca143f 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -248,6 +248,11 @@
status = "okay";
};
+&wifi {
+ status = "okay";
+ qcom,msa_fixed_perm;
+};
+
/* PINCTRL - additions to nodes defined in sc7180.dtsi */
&qup_i2c2_default {
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index 666e9b9..7efb97f 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -42,6 +42,12 @@
compatible = "qcom,cmd-db";
no-map;
};
+
+ wlan_fw_mem: memory@93900000 {
+ compatible = "removed-dma-pool";
+ no-map;
+ reg = <0 0x93900000 0 0x200000>;
+ };
};
cpus {
@@ -1119,6 +1125,28 @@
#clock-cells = <1>;
};
};
+
+ wifi: wifi@18800000 {
+ compatible = "qcom,wcn3990-wifi";
+ reg = <0 0x18800000 0 0x800000>;
+ reg-names = "membase";
+ iommus = <&apps_smmu 0xC0 0x1>;
+ interrupts =
+ <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH /* CE0 */ >,
+ <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH /* CE1 */ >,
+ <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH /* CE2 */ >,
+ <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH /* CE3 */ >,
+ <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH /* CE4 */ >,
+ <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH /* CE5 */ >,
+ <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH /* CE6 */ >,
+ <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH /* CE7 */ >,
+ <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH /* CE8 */ >,
+ <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH /* CE9 */ >,
+ <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH /* CE10 */>,
+ <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH /* CE11 */>;
+ memory-region = <&wlan_fw_mem>;
+ status = "disabled";
+ };
};
timer {
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v3] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
2019-12-24 9:59 [PATCH v3] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node Rakesh Pillai
@ 2019-12-29 3:14 ` Bjorn Andersson
2019-12-30 4:59 ` pillair
0 siblings, 1 reply; 3+ messages in thread
From: Bjorn Andersson @ 2019-12-29 3:14 UTC (permalink / raw)
To: Rakesh Pillai; +Cc: devicetree, linux-kernel, linux-arm-kernel, linux-arm-msm
On Tue 24 Dec 01:59 PST 2019, Rakesh Pillai wrote:
> Add device node for the ath10k SNOC platform driver probe
> and add resources required for WCN3990 on sc7180 soc.
>
> Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
> ---
> This change is dependent on the below set of changes
> arm64: dts: sc7180: Add qupv3_0 and qupv3_1 (https://lore.kernel.org/patchwork/patch/1150367/)
It would be clearer if you linked to the series instead, but it doesn't
matter at this point, this is merged already.
What doesn't seem to be merged is the addition of the
qcom,msa_fixed_perm property, so I presume I need to hold off on merging
this?
> ---
> arch/arm64/boot/dts/qcom/sc7180-idp.dts | 5 +++++
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 28 ++++++++++++++++++++++++++++
> 2 files changed, 33 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> index 189254f..b2ca143f 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> @@ -248,6 +248,11 @@
> status = "okay";
> };
>
> +&wifi {
> + status = "okay";
> + qcom,msa_fixed_perm;
As remarked by Rob, properties should be using - instead of _.
> +};
> +
> /* PINCTRL - additions to nodes defined in sc7180.dtsi */
>
> &qup_i2c2_default {
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index 666e9b9..7efb97f 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -42,6 +42,12 @@
> compatible = "qcom,cmd-db";
> no-map;
> };
> +
> + wlan_fw_mem: memory@93900000 {
> + compatible = "removed-dma-pool";
> + no-map;
> + reg = <0 0x93900000 0 0x200000>;
> + };
> };
>
> cpus {
> @@ -1119,6 +1125,28 @@
> #clock-cells = <1>;
> };
> };
> +
> + wifi: wifi@18800000 {
> + compatible = "qcom,wcn3990-wifi";
> + reg = <0 0x18800000 0 0x800000>;
> + reg-names = "membase";
> + iommus = <&apps_smmu 0xC0 0x1>;
Lowercase 'c' please.
Regards,
Bjorn
> + interrupts =
> + <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH /* CE0 */ >,
> + <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH /* CE1 */ >,
> + <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH /* CE2 */ >,
> + <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH /* CE3 */ >,
> + <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH /* CE4 */ >,
> + <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH /* CE5 */ >,
> + <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH /* CE6 */ >,
> + <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH /* CE7 */ >,
> + <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH /* CE8 */ >,
> + <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH /* CE9 */ >,
> + <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH /* CE10 */>,
> + <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH /* CE11 */>;
> + memory-region = <&wlan_fw_mem>;
> + status = "disabled";
> + };
> };
>
> timer {
> --
> 2.7.4
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 3+ messages in thread
* RE: [PATCH v3] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
2019-12-29 3:14 ` Bjorn Andersson
@ 2019-12-30 4:59 ` pillair
0 siblings, 0 replies; 3+ messages in thread
From: pillair @ 2019-12-30 4:59 UTC (permalink / raw)
To: 'Bjorn Andersson'
Cc: devicetree, linux-kernel, linux-arm-kernel, linux-arm-msm
Hi Bjorn,
Thanks for the comments.
I will post an updated patchset v4 after the patch bringing-in
"qcom,msa-fixed-perm" is merged/approved.
I will address all the comments together.
Thanks,
Rakesh Pillai.
> -----Original Message-----
> From: Bjorn Andersson <bjorn.andersson@linaro.org>
> Sent: Sunday, December 29, 2019 8:44 AM
> To: Rakesh Pillai <pillair@codeaurora.org>
> Cc: devicetree@vger.kernel.org; linux-arm-msm@vger.kernel.org; linux-
> kernel@vger.kernel.org; linux-arm-kernel@lists.infradead.org
> Subject: Re: [PATCH v3] arm64: dts: qcom: sc7180: Add WCN3990 WLAN
> module device node
>
> On Tue 24 Dec 01:59 PST 2019, Rakesh Pillai wrote:
>
> > Add device node for the ath10k SNOC platform driver probe
> > and add resources required for WCN3990 on sc7180 soc.
> >
> > Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
> > ---
> > This change is dependent on the below set of changes
> > arm64: dts: sc7180: Add qupv3_0 and qupv3_1
> (https://lore.kernel.org/patchwork/patch/1150367/)
>
> It would be clearer if you linked to the series instead, but it doesn't
> matter at this point, this is merged already.
>
> What doesn't seem to be merged is the addition of the
> qcom,msa_fixed_perm property, so I presume I need to hold off on merging
> this?
>
> > ---
> > arch/arm64/boot/dts/qcom/sc7180-idp.dts | 5 +++++
> > arch/arm64/boot/dts/qcom/sc7180.dtsi | 28
> ++++++++++++++++++++++++++++
> > 2 files changed, 33 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > index 189254f..b2ca143f 100644
> > --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > @@ -248,6 +248,11 @@
> > status = "okay";
> > };
> >
> > +&wifi {
> > + status = "okay";
> > + qcom,msa_fixed_perm;
>
> As remarked by Rob, properties should be using - instead of _.
>
> > +};
> > +
> > /* PINCTRL - additions to nodes defined in sc7180.dtsi */
> >
> > &qup_i2c2_default {
> > diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > index 666e9b9..7efb97f 100644
> > --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > @@ -42,6 +42,12 @@
> > compatible = "qcom,cmd-db";
> > no-map;
> > };
> > +
> > + wlan_fw_mem: memory@93900000 {
> > + compatible = "removed-dma-pool";
> > + no-map;
> > + reg = <0 0x93900000 0 0x200000>;
> > + };
> > };
> >
> > cpus {
> > @@ -1119,6 +1125,28 @@
> > #clock-cells = <1>;
> > };
> > };
> > +
> > + wifi: wifi@18800000 {
> > + compatible = "qcom,wcn3990-wifi";
> > + reg = <0 0x18800000 0 0x800000>;
> > + reg-names = "membase";
> > + iommus = <&apps_smmu 0xC0 0x1>;
>
> Lowercase 'c' please.
>
> Regards,
> Bjorn
>
> > + interrupts =
> > + <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH /* CE0
> */ >,
> > + <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH /* CE1
> */ >,
> > + <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH /* CE2
> */ >,
> > + <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH /* CE3
> */ >,
> > + <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH /* CE4
> */ >,
> > + <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH /* CE5
> */ >,
> > + <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH /* CE6
> */ >,
> > + <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH /* CE7
> */ >,
> > + <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH /* CE8
> */ >,
> > + <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH /* CE9
> */ >,
> > + <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH /* CE10
> */>,
> > + <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH /* CE11
> */>;
> > + memory-region = <&wlan_fw_mem>;
> > + status = "disabled";
> > + };
> > };
> >
> > timer {
> > --
> > 2.7.4
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2019-12-30 5:00 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-12-24 9:59 [PATCH v3] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node Rakesh Pillai
2019-12-29 3:14 ` Bjorn Andersson
2019-12-30 4:59 ` pillair
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).