[PATCHv3 00/17] I2C Big cleanup

[PATCHv3 00/17] I2C Big cleanup

[Shubhrajyoti D]

I have dropped a few patches from the series and also
tested every single patch on my pandaboard.

There's still lots of work to be done on the i2c-omap.c
driver but it's now easier to read, IMO.

Changes since v1:
       - removed tabification on patch 6/17
       - removed dev_err() which was introduced on patch 09/17
Changes since v2:
	- do not set full fifo depth in the RDR interrupt.
	- some changelog updates.
	- rebase to the Wolfram's tree.

Tested on omap4sdp and 3430sdp.
Functional testing.
Also did suspend resume.
For omap3 the per domain seems to be OK.

This applies on Wolfram's i2c-embedded/for-next branch
plus the below series
http://www.spinics.net/lists/linux-omap/msg72901.html


are available in the git repository at:
  git://gitorious.org/linus-tree/linus-tree.git for_next/omap/big_cleanup



Felipe Balbi (17):
  i2c: omap: switch to devm_* API
  i2c: omap: simplify num_bytes handling
  i2c: omap: decrease indentation level on data handling
  i2c: omap: add blank lines
  i2c: omap: simplify omap_i2c_ack_stat()
  i2c: omap: split out [XR]DR and [XR]RDY
  i2c: omap: improve i462 errata handling
  i2c: omap: re-factor receive/transmit data loop
  i2c: omap: switch over to do {} while loop
  i2c: omap: ack IRQ in parts
  i2c: omap: switch to platform_get_irq()
  i2c: omap: bus: add a receiver flag
  i2c: omap: simplify errata check
  i2c: omap: always return IRQ_HANDLED
  i2c: omap: simplify IRQ exit path
  i2c: omap: resize fifos before each message
  i2c: omap: get rid of the "complete" label

 drivers/i2c/busses/i2c-omap.c |  394 ++++++++++++++++++++++++-----------------
 1 files changed, 232 insertions(+), 162 deletions(-)

-- 
1.7.5.4

[PATCHv3 01/17] i2c: omap: switch to devm_* API

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

that helps deleting some boiler plate code
and lets driver-core manage our resources
for us.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
 drivers/i2c/busses/i2c-omap.c |   40 +++++++++++-----------------------------
 1 files changed, 11 insertions(+), 29 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index feb15dd..7ad4efd 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -962,7 +962,7 @@ omap_i2c_probe(struct platform_device *pdev)
 {
 	struct omap_i2c_dev	*dev;
 	struct i2c_adapter	*adap;
-	struct resource		*mem, *irq, *ioarea;
+	struct resource		*mem, *irq;
 	struct omap_i2c_bus_platform_data *pdata = pdev->dev.platform_data;
 	struct device_node	*node = pdev->dev.of_node;
 	const struct of_device_id *match;
@@ -981,17 +981,16 @@ omap_i2c_probe(struct platform_device *pdev)
 		return -ENODEV;
 	}
 
-	ioarea = request_mem_region(mem->start, resource_size(mem),
-			pdev->name);
-	if (!ioarea) {
-		dev_err(&pdev->dev, "I2C region already claimed\n");
-		return -EBUSY;
+	dev = devm_kzalloc(&pdev->dev, sizeof(struct omap_i2c_dev), GFP_KERNEL);
+	if (!dev) {
+		dev_err(&pdev->dev, "Menory allocation failed\n");
+		return -ENOMEM;
 	}
 
-	dev = kzalloc(sizeof(struct omap_i2c_dev), GFP_KERNEL);
-	if (!dev) {
-		r = -ENOMEM;
-		goto err_release_region;
+	dev->base = devm_request_and_ioremap(&pdev->dev, mem);
+	if (!dev->base) {
+		dev_err(&pdev->dev, "I2C region already claimed\n");
+		return -ENOMEM;
 	}
 
 	match = of_match_device(of_match_ptr(omap_i2c_of_match), &pdev->dev);
@@ -1014,11 +1013,6 @@ omap_i2c_probe(struct platform_device *pdev)
 
 	dev->dev = &pdev->dev;
 	dev->irq = irq->start;
-	dev->base = ioremap(mem->start, resource_size(mem));
-	if (!dev->base) {
-		r = -ENOMEM;
-		goto err_free_mem;
-	}
 
 	platform_set_drvdata(pdev, dev);
 	init_completion(&dev->cmd_complete);
@@ -1076,7 +1070,7 @@ omap_i2c_probe(struct platform_device *pdev)
 
 	isr = (dev->rev < OMAP_I2C_OMAP1_REV_2) ? omap_i2c_omap1_isr :
 								   omap_i2c_isr;
-	r = request_irq(dev->irq, isr, IRQF_NO_SUSPEND, pdev->name, dev);
+	r = devm_request_irq(&pdev->dev, dev->irq, isr, IRQF_NO_SUSPEND, pdev->name, dev);
 
 	if (r) {
 		dev_err(dev->dev, "failure requesting irq %i\n", dev->irq);
@@ -1100,7 +1094,7 @@ omap_i2c_probe(struct platform_device *pdev)
 	r = i2c_add_numbered_adapter(adap);
 	if (r) {
 		dev_err(dev->dev, "failure adding adapter\n");
-		goto err_free_irq;
+		goto err_unuse_clocks;
 	}
 
 	of_i2c_register_devices(adap);
@@ -1109,18 +1103,12 @@ omap_i2c_probe(struct platform_device *pdev)
 
 	return 0;
 
-err_free_irq:
-	free_irq(dev->irq, dev);
 err_unuse_clocks:
 	omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
 err_free_mem:
 	pm_runtime_put(dev->dev);
-	iounmap(dev->base);
 	pm_runtime_disable(&pdev->dev);
 	platform_set_drvdata(pdev, NULL);
-	kfree(dev);
-err_release_region:
-	release_mem_region(mem->start, resource_size(mem));
 
 	return r;
 }
@@ -1128,12 +1116,10 @@ err_release_region:
 static int __devexit omap_i2c_remove(struct platform_device *pdev)
 {
 	struct omap_i2c_dev	*dev = platform_get_drvdata(pdev);
-	struct resource		*mem;
 	int ret;
 
 	platform_set_drvdata(pdev, NULL);
 
-	free_irq(dev->irq, dev);
 	i2c_del_adapter(&dev->adapter);
 	ret = pm_runtime_get_sync(&pdev->dev);
 	if (!IS_ERR_VALUE(ret))
@@ -1141,10 +1127,6 @@ static int __devexit omap_i2c_remove(struct platform_device *pdev)
 
 	pm_runtime_put(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
-	iounmap(dev->base);
-	kfree(dev);
-	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	release_mem_region(mem->start, resource_size(mem));
 	return 0;
 }
 
-- 
1.7.5.4

[PATCHv3 02/17] i2c: omap: simplify num_bytes handling

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

trivial patch, no functional changes

If the fifo is disabled or fifo_size is 0 the num_bytes
is set to 1. Else it is set to fifo_size or in case of a
draining interrupt the remaining bytes in the buff stat.
So the zero check is redundant and can be safely optimised.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
 drivers/i2c/busses/i2c-omap.c |    6 ++----
 1 files changed, 2 insertions(+), 4 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 7ad4efd..1df2bc9 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -831,8 +831,7 @@ complete:
 							OMAP_I2C_BUFSTAT_REG)
 							>> 8) & 0x3F;
 			}
-			while (num_bytes) {
-				num_bytes--;
+			while (num_bytes--) {
 				w = omap_i2c_read_reg(dev, OMAP_I2C_DATA_REG);
 				if (dev->buf_len) {
 					*dev->buf++ = w;
@@ -874,8 +873,7 @@ complete:
 							OMAP_I2C_BUFSTAT_REG)
 							& 0x3F;
 			}
-			while (num_bytes) {
-				num_bytes--;
+			while (num_bytes--) {
 				w = 0;
 				if (dev->buf_len) {
 					w = *dev->buf++;
-- 
1.7.5.4

[PATCHv3 03/17] i2c: omap: decrease indentation level on data handling

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

The patch intends to decrease the indentation level on the
data handling
by using the fact that else of if (dev->buf_len) is same as
if (!dev->buf_len)

if (dev->buf_len) {
	aaa;
} else {
	bbb;
	break;
}

to

if (!dev->buf_len) {
        bbb;
        break;
}
aaa;

Hence no functional changes.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
- Changelogs updated.
 drivers/i2c/busses/i2c-omap.c |   63 ++++++++++++++++++++---------------------
 1 files changed, 31 insertions(+), 32 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 1df2bc9..f67e998 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -832,22 +832,7 @@ complete:
 							>> 8) & 0x3F;
 			}
 			while (num_bytes--) {
-				w = omap_i2c_read_reg(dev, OMAP_I2C_DATA_REG);
-				if (dev->buf_len) {
-					*dev->buf++ = w;
-					dev->buf_len--;
-					/*
-					 * Data reg in 2430, omap3 and
-					 * omap4 is 8 bit wide
-					 */
-					if (dev->flags &
-						 OMAP_I2C_FLAG_16BIT_DATA_REG) {
-						if (dev->buf_len) {
-							*dev->buf++ = w >> 8;
-							dev->buf_len--;
-						}
-					}
-				} else {
+				if (!dev->buf_len) {
 					if (stat & OMAP_I2C_STAT_RRDY)
 						dev_err(dev->dev,
 							"RRDY IRQ while no data"
@@ -858,6 +843,21 @@ complete:
 								" requested\n");
 					break;
 				}
+
+				w = omap_i2c_read_reg(dev, OMAP_I2C_DATA_REG);
+				*dev->buf++ = w;
+				dev->buf_len--;
+				/*
+				 * Data reg in 2430, omap3 and
+				 * omap4 is 8 bit wide
+				 */
+				if (dev->flags &
+						OMAP_I2C_FLAG_16BIT_DATA_REG) {
+					if (dev->buf_len) {
+						*dev->buf++ = w >> 8;
+						dev->buf_len--;
+					}
+				}
 			}
 			omap_i2c_ack_stat(dev,
 				stat & (OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR));
@@ -874,22 +874,7 @@ complete:
 							& 0x3F;
 			}
 			while (num_bytes--) {
-				w = 0;
-				if (dev->buf_len) {
-					w = *dev->buf++;
-					dev->buf_len--;
-					/*
-					 * Data reg in 2430, omap3 and
-					 * omap4 is 8 bit wide
-					 */
-					if (dev->flags &
-						 OMAP_I2C_FLAG_16BIT_DATA_REG) {
-						if (dev->buf_len) {
-							w |= *dev->buf++ << 8;
-							dev->buf_len--;
-						}
-					}
-				} else {
+				if (!dev->buf_len) {
 					if (stat & OMAP_I2C_STAT_XRDY)
 						dev_err(dev->dev,
 							"XRDY IRQ while no "
@@ -901,6 +886,20 @@ complete:
 					break;
 				}
 
+				w = *dev->buf++;
+				dev->buf_len--;
+				/*
+				 * Data reg in 2430, omap3 and
+				 * omap4 is 8 bit wide
+				 */
+				if (dev->flags &
+						OMAP_I2C_FLAG_16BIT_DATA_REG) {
+					if (dev->buf_len) {
+						w |= *dev->buf++ << 8;
+						dev->buf_len--;
+					}
+				}
+
 				if ((dev->errata & I2C_OMAP_ERRATA_I462) &&
 				    errata_omap3_i462(dev, &stat, &err))
 					goto complete;
-- 
1.7.5.4

[PATCHv3 04/17] i2c: omap: add blank lines

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

trivial patch to aid readability. No functional
changes.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
 drivers/i2c/busses/i2c-omap.c |    5 +++++
 1 files changed, 5 insertions(+), 0 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index f67e998..7be661e 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -805,6 +805,7 @@ complete:
 			dev_err(dev->dev, "Arbitration lost\n");
 			err |= OMAP_I2C_STAT_AL;
 		}
+
 		/*
 		 * ProDB0017052: Clear ARDY bit twice
 		 */
@@ -817,6 +818,7 @@ complete:
 			omap_i2c_complete_cmd(dev, err);
 			return IRQ_HANDLED;
 		}
+
 		if (stat & (OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR)) {
 			u8 num_bytes = 1;
 
@@ -863,6 +865,7 @@ complete:
 				stat & (OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR));
 			continue;
 		}
+
 		if (stat & (OMAP_I2C_STAT_XRDY | OMAP_I2C_STAT_XDR)) {
 			u8 num_bytes = 1;
 			if (dev->fifo_size) {
@@ -910,10 +913,12 @@ complete:
 				stat & (OMAP_I2C_STAT_XRDY | OMAP_I2C_STAT_XDR));
 			continue;
 		}
+
 		if (stat & OMAP_I2C_STAT_ROVR) {
 			dev_err(dev->dev, "Receive overrun\n");
 			dev->cmd_err |= OMAP_I2C_STAT_ROVR;
 		}
+
 		if (stat & OMAP_I2C_STAT_XUDF) {
 			dev_err(dev->dev, "Transmit underflow\n");
 			dev->cmd_err |= OMAP_I2C_STAT_XUDF;
-- 
1.7.5.4

[PATCHv3 05/17] i2c: omap: simplify omap_i2c_ack_stat()

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

stat & BIT(1) is the same as BIT(1), so let's
simplify things a bit by removing "stat &" from
all omap_i2c_ack_stat() calls.

Code snippet (extremely simplified):

if (stat & NACK) {
        ...
        omap_i2c_ack_stat(dev, stat & NACK);
}

if (stat & RDR) {
        ...
        omap_i2c_ack_stat(dev, stat & RDR);
}

and so on. The tricky place is only WRT errata handling, for example:

if (*stat & (NACK | AL)) {
        omap_i2c_ack_stat(dev, *stat & (XRDY | XDR));
        ...
}

but in this case, the errata says we must clear XRDY and XDR if that
errata triggers, so if they just got enabled or not, it doesn't matter.

Another tricky place is RDR | RRDY (likewise for XDR | XRDY):

if (stat & (RDR | RRDY)) {
        ...
        omap_i2c_ack_stat(dev, stat & (RDR | RRDY));
}

again here there will be no issues because those IRQs never fire
simultaneously and one will only after after we have handled the
previous, that's because the same FIFO is used anyway and we won't shift
data into FIFO until we tell the IP "hey, I'm done with the FIFO, you
can shift more data"

Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---

- Added the explaination from the discurssion to the commit logs
as per Wolfram's suggestion.

 drivers/i2c/busses/i2c-omap.c |   19 ++++++++++---------
 1 files changed, 10 insertions(+), 9 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 7be661e..359ee08 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -750,7 +750,7 @@ static int errata_omap3_i462(struct omap_i2c_dev *dev, u16 *stat, int *err)
 
 	while (--timeout && !(*stat & OMAP_I2C_STAT_XUDF)) {
 		if (*stat & (OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) {
-			omap_i2c_ack_stat(dev, *stat & (OMAP_I2C_STAT_XRDY |
+			omap_i2c_ack_stat(dev, (OMAP_I2C_STAT_XRDY |
 							OMAP_I2C_STAT_XDR));
 			return -ETIMEDOUT;
 		}
@@ -811,10 +811,11 @@ complete:
 		 */
 		if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK |
 					OMAP_I2C_STAT_AL)) {
-			omap_i2c_ack_stat(dev, stat &
-				(OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR |
-				OMAP_I2C_STAT_XRDY | OMAP_I2C_STAT_XDR |
-				OMAP_I2C_STAT_ARDY));
+			omap_i2c_ack_stat(dev, (OMAP_I2C_STAT_RRDY |
+						OMAP_I2C_STAT_RDR |
+						OMAP_I2C_STAT_XRDY |
+						OMAP_I2C_STAT_XDR |
+						OMAP_I2C_STAT_ARDY));
 			omap_i2c_complete_cmd(dev, err);
 			return IRQ_HANDLED;
 		}
@@ -861,8 +862,8 @@ complete:
 					}
 				}
 			}
-			omap_i2c_ack_stat(dev,
-				stat & (OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR));
+			omap_i2c_ack_stat(dev, (OMAP_I2C_STAT_RRDY |
+						OMAP_I2C_STAT_RDR));
 			continue;
 		}
 
@@ -909,8 +910,8 @@ complete:
 
 				omap_i2c_write_reg(dev, OMAP_I2C_DATA_REG, w);
 			}
-			omap_i2c_ack_stat(dev,
-				stat & (OMAP_I2C_STAT_XRDY | OMAP_I2C_STAT_XDR));
+			omap_i2c_ack_stat(dev, (OMAP_I2C_STAT_XRDY |
+						OMAP_I2C_STAT_XDR));
 			continue;
 		}
 
-- 
1.7.5.4

[PATCHv3 06/17] i2c: omap: split out [XR]DR and [XR]RDY

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

While they do pretty much the same thing, there
are a few peculiarities. Specially WRT erratas,
it's best to split those out and re-factor the
read/write loop to another function which both
cases call.

This last part will be done on another patch.

While at that, also avoid an unncessary register
read since dev->fifo_len will always contain the
correct amount of data to be transferred.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
 drivers/i2c/busses/i2c-omap.c |  126 ++++++++++++++++++++++++++++++----------
 1 files changed, 94 insertions(+), 32 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 359ee08..45bd731 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -820,36 +820,64 @@ complete:
 			return IRQ_HANDLED;
 		}
 
-		if (stat & (OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR)) {
+		if (stat & OMAP_I2C_STAT_RDR) {
 			u8 num_bytes = 1;
 
+			if (dev->fifo_size)
+				num_bytes = (omap_i2c_read_reg(dev,
+						OMAP_I2C_BUFSTAT_REG) >> 8)
+						& 0x3F;
+
+			while (num_bytes--) {
+				if (!dev->buf_len) {
+					dev_err(dev->dev,
+							"RDR IRQ while no data"
+							" requested\n");
+					break;
+				}
+
+				w = omap_i2c_read_reg(dev, OMAP_I2C_DATA_REG);
+				*dev->buf++ = w;
+				dev->buf_len--;
+
+				/*
+				 * Data reg in 2430, omap3 and
+				 * omap4 is 8 bit wide
+				 */
+				if (dev->flags &
+						OMAP_I2C_FLAG_16BIT_DATA_REG) {
+					if (dev->buf_len) {
+						*dev->buf++ = w >> 8;
+						dev->buf_len--;
+					}
+				}
+			}
+
 			if (dev->errata & I2C_OMAP_ERRATA_I207)
 				i2c_omap_errata_i207(dev, stat);
 
-			if (dev->fifo_size) {
-				if (stat & OMAP_I2C_STAT_RRDY)
-					num_bytes = dev->fifo_size;
-				else    /* read RXSTAT on RDR interrupt */
-					num_bytes = (omap_i2c_read_reg(dev,
-							OMAP_I2C_BUFSTAT_REG)
-							>> 8) & 0x3F;
-			}
+			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_RDR);
+			continue;
+		}
+
+		if (stat & OMAP_I2C_STAT_RRDY) {
+			u8 num_bytes = 1;
+
+			if (dev->fifo_size)
+				num_bytes = dev->fifo_size;
+
 			while (num_bytes--) {
 				if (!dev->buf_len) {
-					if (stat & OMAP_I2C_STAT_RRDY)
-						dev_err(dev->dev,
+					dev_err(dev->dev,
 							"RRDY IRQ while no data"
-								" requested\n");
-					if (stat & OMAP_I2C_STAT_RDR)
-						dev_err(dev->dev,
-							"RDR IRQ while no data"
-								" requested\n");
+							" requested\n");
 					break;
 				}
 
 				w = omap_i2c_read_reg(dev, OMAP_I2C_DATA_REG);
 				*dev->buf++ = w;
 				dev->buf_len--;
+
 				/*
 				 * Data reg in 2430, omap3 and
 				 * omap4 is 8 bit wide
@@ -862,36 +890,70 @@ complete:
 					}
 				}
 			}
-			omap_i2c_ack_stat(dev, (OMAP_I2C_STAT_RRDY |
-						OMAP_I2C_STAT_RDR));
+
+			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_RRDY);
 			continue;
 		}
 
-		if (stat & (OMAP_I2C_STAT_XRDY | OMAP_I2C_STAT_XDR)) {
+		if (stat & OMAP_I2C_STAT_XDR) {
 			u8 num_bytes = 1;
-			if (dev->fifo_size) {
-				if (stat & OMAP_I2C_STAT_XRDY)
-					num_bytes = dev->fifo_size;
-				else    /* read TXSTAT on XDR interrupt */
-					num_bytes = omap_i2c_read_reg(dev,
+
+			if (dev->fifo_size)
+				num_bytes = omap_i2c_read_reg(dev,
 							OMAP_I2C_BUFSTAT_REG)
 							& 0x3F;
+
+			while (num_bytes--) {
+				if (!dev->buf_len) {
+					dev_err(dev->dev,
+							"XDR IRQ while no "
+							"data to send\n");
+					break;
+				}
+
+				w = *dev->buf++;
+				dev->buf_len--;
+
+				/*
+				 * Data reg in 2430, omap3 and
+				 * omap4 is 8 bit wide
+				 */
+				if (dev->flags &
+						OMAP_I2C_FLAG_16BIT_DATA_REG) {
+					if (dev->buf_len) {
+						w |= *dev->buf++ << 8;
+						dev->buf_len--;
+					}
+				}
+
+				if ((dev->errata & I2C_OMAP_ERRATA_I462) &&
+				    errata_omap3_i462(dev, &stat, &err))
+					goto complete;
+
+				omap_i2c_write_reg(dev, OMAP_I2C_DATA_REG, w);
 			}
+
+			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_XDR);
+			continue;
+		}
+
+		if (stat & OMAP_I2C_STAT_XRDY) {
+			u8 num_bytes = 1;
+
+			if (dev->fifo_size)
+				num_bytes = dev->fifo_size;
+
 			while (num_bytes--) {
 				if (!dev->buf_len) {
-					if (stat & OMAP_I2C_STAT_XRDY)
-						dev_err(dev->dev,
+					dev_err(dev->dev,
 							"XRDY IRQ while no "
 							"data to send\n");
-					if (stat & OMAP_I2C_STAT_XDR)
-						dev_err(dev->dev,
-							"XDR IRQ while no "
-							"data to send\n");
 					break;
 				}
 
 				w = *dev->buf++;
 				dev->buf_len--;
+
 				/*
 				 * Data reg in 2430, omap3 and
 				 * omap4 is 8 bit wide
@@ -910,8 +972,8 @@ complete:
 
 				omap_i2c_write_reg(dev, OMAP_I2C_DATA_REG, w);
 			}
-			omap_i2c_ack_stat(dev, (OMAP_I2C_STAT_XRDY |
-						OMAP_I2C_STAT_XDR));
+
+			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_XRDY);
 			continue;
 		}
 
-- 
1.7.5.4

[PATCHv3 07/17] i2c: omap: improve i462 errata handling

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

Make it not depend on ISR's local variables
in order to make it easier to re-factor the
transmit data loop.
Also since we are waiting for XUDF just before
writing data lets not flag the underflow.
This is anyways going to go once we write
the data.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
 drivers/i2c/busses/i2c-omap.c |   43 ++++++++++++++++++++++++++++------------
 1 files changed, 30 insertions(+), 13 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 45bd731..870452d 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -744,27 +744,30 @@ omap_i2c_omap1_isr(int this_irq, void *dev_id)
  * data to DATA_REG. Otherwise some data bytes can be lost while transferring
  * them from the memory to the I2C interface.
  */
-static int errata_omap3_i462(struct omap_i2c_dev *dev, u16 *stat, int *err)
+static int errata_omap3_i462(struct omap_i2c_dev *dev)
 {
 	unsigned long timeout = 10000;
+	u16 stat;
 
-	while (--timeout && !(*stat & OMAP_I2C_STAT_XUDF)) {
-		if (*stat & (OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) {
+	do {
+		stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);
+		if (stat & OMAP_I2C_STAT_XUDF)
+			break;
+
+		if (stat & (OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) {
 			omap_i2c_ack_stat(dev, (OMAP_I2C_STAT_XRDY |
 							OMAP_I2C_STAT_XDR));
-			return -ETIMEDOUT;
+			return -EIO;
 		}
 
 		cpu_relax();
-		*stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);
-	}
+	} while (--timeout);
 
 	if (!timeout) {
 		dev_err(dev->dev, "timeout waiting on XUDF bit\n");
 		return 0;
 	}
 
-	*err |= OMAP_I2C_STAT_XUDF;
 	return 0;
 }
 
@@ -926,9 +929,16 @@ complete:
 					}
 				}
 
-				if ((dev->errata & I2C_OMAP_ERRATA_I462) &&
-				    errata_omap3_i462(dev, &stat, &err))
-					goto complete;
+				if (dev->errata & I2C_OMAP_ERRATA_I462) {
+					int ret;
+
+					ret = errata_omap3_i462(dev);
+					stat = omap_i2c_read_reg(dev,
+							OMAP_I2C_STAT_REG);
+
+					if (ret < 0)
+						goto complete;
+				}
 
 				omap_i2c_write_reg(dev, OMAP_I2C_DATA_REG, w);
 			}
@@ -966,9 +976,16 @@ complete:
 					}
 				}
 
-				if ((dev->errata & I2C_OMAP_ERRATA_I462) &&
-				    errata_omap3_i462(dev, &stat, &err))
-					goto complete;
+				if (dev->errata & I2C_OMAP_ERRATA_I462) {
+					int ret;
+
+					ret = errata_omap3_i462(dev);
+					stat = omap_i2c_read_reg(dev,
+							OMAP_I2C_STAT_REG);
+
+					if (ret < 0)
+						goto complete;
+				}
 
 				omap_i2c_write_reg(dev, OMAP_I2C_DATA_REG, w);
 			}
-- 
1.7.5.4

[PATCHv3 08/17] i2c: omap: re-factor receive/transmit data loop

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

re-factor the common parts to a separate function,
so that code is easier to read and understand.

No functional changes.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
 drivers/i2c/busses/i2c-omap.c |  204 ++++++++++++++++------------------------
 1 files changed, 82 insertions(+), 122 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 870452d..d57b75d 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -771,12 +771,81 @@ static int errata_omap3_i462(struct omap_i2c_dev *dev)
 	return 0;
 }
 
+static void omap_i2c_receive_data(struct omap_i2c_dev *dev, u8 num_bytes,
+		bool is_rdr)
+{
+	u16		w;
+
+	while (num_bytes--) {
+		if (!dev->buf_len) {
+			dev_err(dev->dev, "%s without data",
+					is_rdr ? "RDR" : "RRDY");
+			break;
+		}
+
+		w = omap_i2c_read_reg(dev, OMAP_I2C_DATA_REG);
+		*dev->buf++ = w;
+		dev->buf_len--;
+
+		/*
+		 * Data reg in 2430, omap3 and
+		 * omap4 is 8 bit wide
+		 */
+		if (dev->flags & OMAP_I2C_FLAG_16BIT_DATA_REG) {
+			if (dev->buf_len) {
+				*dev->buf++ = w >> 8;
+				dev->buf_len--;
+			}
+		}
+	}
+}
+
+static int omap_i2c_transmit_data(struct omap_i2c_dev *dev, u8 num_bytes,
+		bool is_xdr)
+{
+	u16		w;
+
+	while (num_bytes--) {
+		if (!dev->buf_len) {
+			dev_err(dev->dev, "%s without data",
+					is_xdr ? "XDR" : "XRDY");
+			break;
+		}
+
+		w = *dev->buf++;
+		dev->buf_len--;
+
+		/*
+		 * Data reg in 2430, omap3 and
+		 * omap4 is 8 bit wide
+		 */
+		if (dev->flags & OMAP_I2C_FLAG_16BIT_DATA_REG) {
+			if (dev->buf_len) {
+				w |= *dev->buf++ << 8;
+				dev->buf_len--;
+			}
+		}
+
+		if (dev->errata & I2C_OMAP_ERRATA_I462) {
+			int ret;
+
+			ret = errata_omap3_i462(dev);
+			if (ret < 0)
+				return ret;
+		}
+
+		omap_i2c_write_reg(dev, OMAP_I2C_DATA_REG, w);
+	}
+
+	return 0;
+}
+
 static irqreturn_t
 omap_i2c_isr(int this_irq, void *dev_id)
 {
 	struct omap_i2c_dev *dev = dev_id;
 	u16 bits;
-	u16 stat, w;
+	u16 stat;
 	int err, count = 0;
 
 	if (pm_runtime_suspended(dev->dev))
@@ -831,30 +900,7 @@ complete:
 						OMAP_I2C_BUFSTAT_REG) >> 8)
 						& 0x3F;
 
-			while (num_bytes--) {
-				if (!dev->buf_len) {
-					dev_err(dev->dev,
-							"RDR IRQ while no data"
-							" requested\n");
-					break;
-				}
-
-				w = omap_i2c_read_reg(dev, OMAP_I2C_DATA_REG);
-				*dev->buf++ = w;
-				dev->buf_len--;
-
-				/*
-				 * Data reg in 2430, omap3 and
-				 * omap4 is 8 bit wide
-				 */
-				if (dev->flags &
-						OMAP_I2C_FLAG_16BIT_DATA_REG) {
-					if (dev->buf_len) {
-						*dev->buf++ = w >> 8;
-						dev->buf_len--;
-					}
-				}
-			}
+			omap_i2c_receive_data(dev, num_bytes, true);
 
 			if (dev->errata & I2C_OMAP_ERRATA_I207)
 				i2c_omap_errata_i207(dev, stat);
@@ -869,79 +915,24 @@ complete:
 			if (dev->fifo_size)
 				num_bytes = dev->fifo_size;
 
-			while (num_bytes--) {
-				if (!dev->buf_len) {
-					dev_err(dev->dev,
-							"RRDY IRQ while no data"
-							" requested\n");
-					break;
-				}
-
-				w = omap_i2c_read_reg(dev, OMAP_I2C_DATA_REG);
-				*dev->buf++ = w;
-				dev->buf_len--;
-
-				/*
-				 * Data reg in 2430, omap3 and
-				 * omap4 is 8 bit wide
-				 */
-				if (dev->flags &
-						OMAP_I2C_FLAG_16BIT_DATA_REG) {
-					if (dev->buf_len) {
-						*dev->buf++ = w >> 8;
-						dev->buf_len--;
-					}
-				}
-			}
-
+			omap_i2c_receive_data(dev, num_bytes, false);
 			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_RRDY);
 			continue;
 		}
 
 		if (stat & OMAP_I2C_STAT_XDR) {
 			u8 num_bytes = 1;
+			int ret;
 
 			if (dev->fifo_size)
 				num_bytes = omap_i2c_read_reg(dev,
 							OMAP_I2C_BUFSTAT_REG)
 							& 0x3F;
 
-			while (num_bytes--) {
-				if (!dev->buf_len) {
-					dev_err(dev->dev,
-							"XDR IRQ while no "
-							"data to send\n");
-					break;
-				}
-
-				w = *dev->buf++;
-				dev->buf_len--;
-
-				/*
-				 * Data reg in 2430, omap3 and
-				 * omap4 is 8 bit wide
-				 */
-				if (dev->flags &
-						OMAP_I2C_FLAG_16BIT_DATA_REG) {
-					if (dev->buf_len) {
-						w |= *dev->buf++ << 8;
-						dev->buf_len--;
-					}
-				}
-
-				if (dev->errata & I2C_OMAP_ERRATA_I462) {
-					int ret;
-
-					ret = errata_omap3_i462(dev);
-					stat = omap_i2c_read_reg(dev,
-							OMAP_I2C_STAT_REG);
-
-					if (ret < 0)
-						goto complete;
-				}
-
-				omap_i2c_write_reg(dev, OMAP_I2C_DATA_REG, w);
-			}
+			ret = omap_i2c_transmit_data(dev, num_bytes, true);
+			stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);
+			if (ret < 0)
+				goto complete;
 
 			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_XDR);
 			continue;
@@ -949,46 +940,15 @@ complete:
 
 		if (stat & OMAP_I2C_STAT_XRDY) {
 			u8 num_bytes = 1;
+			int ret;
 
 			if (dev->fifo_size)
 				num_bytes = dev->fifo_size;
 
-			while (num_bytes--) {
-				if (!dev->buf_len) {
-					dev_err(dev->dev,
-							"XRDY IRQ while no "
-							"data to send\n");
-					break;
-				}
-
-				w = *dev->buf++;
-				dev->buf_len--;
-
-				/*
-				 * Data reg in 2430, omap3 and
-				 * omap4 is 8 bit wide
-				 */
-				if (dev->flags &
-						OMAP_I2C_FLAG_16BIT_DATA_REG) {
-					if (dev->buf_len) {
-						w |= *dev->buf++ << 8;
-						dev->buf_len--;
-					}
-				}
-
-				if (dev->errata & I2C_OMAP_ERRATA_I462) {
-					int ret;
-
-					ret = errata_omap3_i462(dev);
-					stat = omap_i2c_read_reg(dev,
-							OMAP_I2C_STAT_REG);
-
-					if (ret < 0)
-						goto complete;
-				}
-
-				omap_i2c_write_reg(dev, OMAP_I2C_DATA_REG, w);
-			}
+			ret = omap_i2c_transmit_data(dev, num_bytes, false);
+			stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);
+			if (ret < 0)
+				goto complete;
 
 			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_XRDY);
 			continue;
-- 
1.7.5.4

[PATCHv3 09/17] i2c: omap: switch over to do {} while loop

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

this will make sure that we execute at least once.
No functional changes otherwise.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
 drivers/i2c/busses/i2c-omap.c |   20 ++++++++++++++------
 1 files changed, 14 insertions(+), 6 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index d57b75d..e4b83af 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -846,20 +846,28 @@ omap_i2c_isr(int this_irq, void *dev_id)
 	struct omap_i2c_dev *dev = dev_id;
 	u16 bits;
 	u16 stat;
-	int err, count = 0;
+	int err = 0, count = 0;
 
 	if (pm_runtime_suspended(dev->dev))
 		return IRQ_NONE;
 
-	bits = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG);
-	while ((stat = (omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG))) & bits) {
+	do {
+		bits = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG);
+		stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);
+		stat &= bits;
+
+		if (!stat) {
+			/* my work here is done */
+			return IRQ_HANDLED;
+		}
+
 		dev_dbg(dev->dev, "IRQ (ISR = 0x%04x)\n", stat);
 		if (count++ == 100) {
 			dev_warn(dev->dev, "Too much work in one IRQ\n");
-			break;
+			omap_i2c_complete_cmd(dev, err);
+			return IRQ_HANDLED;
 		}
 
-		err = 0;
 complete:
 		/*
 		 * Ack the stat in one go, but [R/X]DR and [R/X]RDY should be
@@ -963,7 +971,7 @@ complete:
 			dev_err(dev->dev, "Transmit underflow\n");
 			dev->cmd_err |= OMAP_I2C_STAT_XUDF;
 		}
-	}
+	} while (stat);
 
 	return count ? IRQ_HANDLED : IRQ_NONE;
 }
-- 
1.7.5.4

[PATCHv3 10/17] i2c: omap: ack IRQ in parts

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

According to flow diagrams on OMAP TRMs,
we should ACK the IRQ as they happen.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
 drivers/i2c/busses/i2c-omap.c |   28 ++++++++++++++++------------
 1 files changed, 16 insertions(+), 12 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index e4b83af..6e4c2be 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -869,21 +869,19 @@ omap_i2c_isr(int this_irq, void *dev_id)
 		}
 
 complete:
-		/*
-		 * Ack the stat in one go, but [R/X]DR and [R/X]RDY should be
-		 * acked after the data operation is complete.
-		 * Ref: TRM SWPU114Q Figure 18-31
-		 */
-		omap_i2c_write_reg(dev, OMAP_I2C_STAT_REG, stat &
-				~(OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR |
-				OMAP_I2C_STAT_XRDY | OMAP_I2C_STAT_XDR));
-
-		if (stat & OMAP_I2C_STAT_NACK)
+		if (stat & OMAP_I2C_STAT_NACK) {
 			err |= OMAP_I2C_STAT_NACK;
+			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_NACK);
+			omap_i2c_complete_cmd(dev, err);
+			return IRQ_HANDLED;
+		}
 
 		if (stat & OMAP_I2C_STAT_AL) {
 			dev_err(dev->dev, "Arbitration lost\n");
 			err |= OMAP_I2C_STAT_AL;
+			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_NACK);
+			omap_i2c_complete_cmd(dev, err);
+			return IRQ_HANDLED;
 		}
 
 		/*
@@ -964,12 +962,18 @@ complete:
 
 		if (stat & OMAP_I2C_STAT_ROVR) {
 			dev_err(dev->dev, "Receive overrun\n");
-			dev->cmd_err |= OMAP_I2C_STAT_ROVR;
+			err |= OMAP_I2C_STAT_ROVR;
+			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_ROVR);
+			omap_i2c_complete_cmd(dev, err);
+			return IRQ_HANDLED;
 		}
 
 		if (stat & OMAP_I2C_STAT_XUDF) {
 			dev_err(dev->dev, "Transmit underflow\n");
-			dev->cmd_err |= OMAP_I2C_STAT_XUDF;
+			err |= OMAP_I2C_STAT_XUDF;
+			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_XUDF);
+			omap_i2c_complete_cmd(dev, err);
+			return IRQ_HANDLED;
 		}
 	} while (stat);
 
-- 
1.7.5.4

[PATCHv3 11/17] i2c: omap: switch to platform_get_irq()

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

that's a nice helper from drivers core which
will give us the exact IRQ number, instead
of a pointer to an IRQ resource.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
 drivers/i2c/busses/i2c-omap.c |   12 +++++++-----
 1 files changed, 7 insertions(+), 5 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 6e4c2be..9f04976 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -1016,11 +1016,12 @@ omap_i2c_probe(struct platform_device *pdev)
 {
 	struct omap_i2c_dev	*dev;
 	struct i2c_adapter	*adap;
-	struct resource		*mem, *irq;
+	struct resource		*mem;
 	struct omap_i2c_bus_platform_data *pdata = pdev->dev.platform_data;
 	struct device_node	*node = pdev->dev.of_node;
 	const struct of_device_id *match;
 	irq_handler_t isr;
+	int irq;
 	int r;
 
 	/* NOTE: driver uses the static register mapping */
@@ -1029,10 +1030,11 @@ omap_i2c_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev, "no mem resource?\n");
 		return -ENODEV;
 	}
-	irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
-	if (!irq) {
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
 		dev_err(&pdev->dev, "no irq resource?\n");
-		return -ENODEV;
+		return irq;
 	}
 
 	dev = devm_kzalloc(&pdev->dev, sizeof(struct omap_i2c_dev), GFP_KERNEL);
@@ -1066,7 +1068,7 @@ omap_i2c_probe(struct platform_device *pdev)
 	}
 
 	dev->dev = &pdev->dev;
-	dev->irq = irq->start;
+	dev->irq = irq;
 
 	platform_set_drvdata(pdev, dev);
 	init_completion(&dev->cmd_complete);
-- 
1.7.5.4

[PATCHv3 12/17] i2c: omap: bus: add a receiver flag

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

that way we can ignore TX IRQs while in receiver
mode and ignore RX IRQs while in transmitter mode.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
 drivers/i2c/busses/i2c-omap.c |    9 +++++++++
 1 files changed, 9 insertions(+), 0 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 9f04976..00d5adc 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -196,6 +196,7 @@ struct omap_i2c_dev {
 						 */
 	u8			rev;
 	unsigned		b_hw:1;		/* bad h/w fixes */
+	unsigned		receiver:1;	/* true when we're in receiver mode */
 	u16			iestate;	/* Saved interrupt register */
 	u16			pscstate;
 	u16			scllstate;
@@ -512,6 +513,7 @@ static int omap_i2c_xfer_msg(struct i2c_adapter *adap,
 
 	INIT_COMPLETION(dev->cmd_complete);
 	dev->cmd_err = 0;
+	dev->receiver = !!(msg->flags & I2C_M_RD);
 
 	w = OMAP_I2C_CON_EN | OMAP_I2C_CON_MST | OMAP_I2C_CON_STT;
 
@@ -856,6 +858,13 @@ omap_i2c_isr(int this_irq, void *dev_id)
 		stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);
 		stat &= bits;
 
+		/* If we're in receiver mode, ignore XDR/XRDY */
+		if (dev->receiver) {
+			stat &= ~(OMAP_I2C_STAT_XDR | OMAP_I2C_STAT_XRDY);
+		} else {
+			stat &= ~(OMAP_I2C_STAT_RDR | OMAP_I2C_STAT_RRDY);
+		}
+
 		if (!stat) {
 			/* my work here is done */
 			return IRQ_HANDLED;
-- 
1.7.5.4

[PATCHv3 13/17] i2c: omap: simplify errata check

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

omap_i2c_dev is allocated with kzalloc(),
so we need not initialize b_hw to zero.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
 drivers/i2c/busses/i2c-omap.c |    4 +---
 1 files changed, 1 insertions(+), 3 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 00d5adc..c48977c 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -1119,9 +1119,7 @@ omap_i2c_probe(struct platform_device *pdev)
 
 		dev->fifo_size = (dev->fifo_size / 2);
 
-		if (dev->rev >= OMAP_I2C_REV_ON_3630_4430)
-			dev->b_hw = 0; /* Disable hardware fixes */
-		else
+		if (dev->rev < OMAP_I2C_REV_ON_3630_4430)
 			dev->b_hw = 1; /* Enable hardware fixes */
 
 		/* calculate wakeup latency constraint for MPU */
-- 
1.7.5.4

[PATCHv3 14/17] i2c: omap: always return IRQ_HANDLED

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

otherwise we could get our IRQ line disabled due
to many spurious IRQs.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
 drivers/i2c/busses/i2c-omap.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index c48977c..2cd3b9a 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -986,7 +986,7 @@ complete:
 		}
 	} while (stat);
 
-	return count ? IRQ_HANDLED : IRQ_NONE;
+	return IRQ_HANDLED;
 }
 
 static const struct i2c_algorithm omap_i2c_algo = {
-- 
1.7.5.4

[PATCHv3 15/17] i2c: omap: simplify IRQ exit path

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

instead of having multiple return points, use
a goto statement to make that clearer.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
 drivers/i2c/busses/i2c-omap.c |   20 ++++++++------------
 1 files changed, 8 insertions(+), 12 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 2cd3b9a..1196417 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -873,24 +873,21 @@ omap_i2c_isr(int this_irq, void *dev_id)
 		dev_dbg(dev->dev, "IRQ (ISR = 0x%04x)\n", stat);
 		if (count++ == 100) {
 			dev_warn(dev->dev, "Too much work in one IRQ\n");
-			omap_i2c_complete_cmd(dev, err);
-			return IRQ_HANDLED;
+			goto out;
 		}
 
 complete:
 		if (stat & OMAP_I2C_STAT_NACK) {
 			err |= OMAP_I2C_STAT_NACK;
 			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_NACK);
-			omap_i2c_complete_cmd(dev, err);
-			return IRQ_HANDLED;
+			goto out;
 		}
 
 		if (stat & OMAP_I2C_STAT_AL) {
 			dev_err(dev->dev, "Arbitration lost\n");
 			err |= OMAP_I2C_STAT_AL;
 			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_NACK);
-			omap_i2c_complete_cmd(dev, err);
-			return IRQ_HANDLED;
+			goto out;
 		}
 
 		/*
@@ -903,8 +900,7 @@ complete:
 						OMAP_I2C_STAT_XRDY |
 						OMAP_I2C_STAT_XDR |
 						OMAP_I2C_STAT_ARDY));
-			omap_i2c_complete_cmd(dev, err);
-			return IRQ_HANDLED;
+			goto out;
 		}
 
 		if (stat & OMAP_I2C_STAT_RDR) {
@@ -973,19 +969,19 @@ complete:
 			dev_err(dev->dev, "Receive overrun\n");
 			err |= OMAP_I2C_STAT_ROVR;
 			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_ROVR);
-			omap_i2c_complete_cmd(dev, err);
-			return IRQ_HANDLED;
+			goto out;
 		}
 
 		if (stat & OMAP_I2C_STAT_XUDF) {
 			dev_err(dev->dev, "Transmit underflow\n");
 			err |= OMAP_I2C_STAT_XUDF;
 			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_XUDF);
-			omap_i2c_complete_cmd(dev, err);
-			return IRQ_HANDLED;
+			goto out;
 		}
 	} while (stat);
 
+out:
+	omap_i2c_complete_cmd(dev, err);
 	return IRQ_HANDLED;
 }
 
-- 
1.7.5.4

[PATCHv3 16/17] i2c: omap: resize fifos before each message

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

This patch will try to avoid the usage of
draining feature by reconfiguring the FIFO
the start condition of each message based
on the message's size.

By doing that, we will be better utilizing
the FIFO when doing big transfers.

While at that also drop the now uneeded
check for dev->buf_len as we always know
the amount of data to be transmitted.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
 drivers/i2c/busses/i2c-omap.c |   83 +++++++++++++++++++++++++----------------
 1 files changed, 51 insertions(+), 32 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 1196417..ac3bdae 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -190,6 +190,7 @@ struct omap_i2c_dev {
 	u8			*regs;
 	size_t			buf_len;
 	struct i2c_adapter	adapter;
+	u8			threshold;
 	u8			fifo_size;	/* use as flag and value
 						 * fifo_size==0 implies no fifo
 						 * if set, should be trsh+1
@@ -415,13 +416,6 @@ static int omap_i2c_init(struct omap_i2c_dev *dev)
 	omap_i2c_write_reg(dev, OMAP_I2C_SCLL_REG, scll);
 	omap_i2c_write_reg(dev, OMAP_I2C_SCLH_REG, sclh);
 
-	if (dev->fifo_size) {
-		/* Note: setup required fifo size - 1. RTRSH and XTRSH */
-		buf = (dev->fifo_size - 1) << 8 | OMAP_I2C_BUF_RXFIF_CLR |
-			(dev->fifo_size - 1) | OMAP_I2C_BUF_TXFIF_CLR;
-		omap_i2c_write_reg(dev, OMAP_I2C_BUF_REG, buf);
-	}
-
 	/* Take the I2C module out of reset: */
 	omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN);
 
@@ -482,6 +476,45 @@ static int omap_i2c_bus_clear(struct omap_i2c_dev *dev)
 	return omap_i2c_wait_for_bb(dev);
 }
 
+static void omap_i2c_resize_fifo(struct omap_i2c_dev *dev, u8 size, bool is_rx)
+{
+	u16		buf;
+
+	if (dev->flags & OMAP_I2C_FLAG_NO_FIFO)
+		return;
+
+	/*
+	 * Set up notification threshold based on message size. We're doing
+	 * this to try and avoid draining feature as much as possible. Whenever
+	 * we have big messages to transfer (bigger than our total fifo size)
+	 * then we might use draining feature to transfer the remaining bytes.
+	 */
+
+	dev->threshold = clamp(size, (u8) 1, dev->fifo_size);
+
+	buf = omap_i2c_read_reg(dev, OMAP_I2C_BUF_REG);
+
+	if (is_rx) {
+		/* Clear RX Threshold */
+		buf &= ~(0x3f << 8);
+		buf |= ((dev->threshold - 1) << 8) | OMAP_I2C_BUF_RXFIF_CLR;
+	} else {
+		/* Clear TX Threshold */
+		buf &= ~0x3f;
+		buf |= (dev->threshold - 1) | OMAP_I2C_BUF_TXFIF_CLR;
+	}
+
+	omap_i2c_write_reg(dev, OMAP_I2C_BUF_REG, buf);
+
+	if (dev->rev < OMAP_I2C_REV_ON_3630_4430)
+		dev->b_hw = 1; /* Enable hardware fixes */
+
+	/* calculate wakeup latency constraint for MPU */
+	if (dev->set_mpu_wkup_lat != NULL)
+		dev->latency = (1000000 * dev->threshold) /
+			(1000 * dev->speed / 8);
+}
+
 /*
  * Low level master read/write transaction.
  */
@@ -498,6 +531,9 @@ static int omap_i2c_xfer_msg(struct i2c_adapter *adap,
 	if (msg->len == 0)
 		return -EINVAL;
 
+	dev->receiver = !!(msg->flags & I2C_M_RD);
+	omap_i2c_resize_fifo(dev, msg->len, dev->receiver);
+
 	omap_i2c_write_reg(dev, OMAP_I2C_SA_REG, msg->addr);
 
 	/* REVISIT: Could the STB bit of I2C_CON be used with probing? */
@@ -513,7 +549,6 @@ static int omap_i2c_xfer_msg(struct i2c_adapter *adap,
 
 	INIT_COMPLETION(dev->cmd_complete);
 	dev->cmd_err = 0;
-	dev->receiver = !!(msg->flags & I2C_M_RD);
 
 	w = OMAP_I2C_CON_EN | OMAP_I2C_CON_MST | OMAP_I2C_CON_STT;
 
@@ -779,12 +814,6 @@ static void omap_i2c_receive_data(struct omap_i2c_dev *dev, u8 num_bytes,
 	u16		w;
 
 	while (num_bytes--) {
-		if (!dev->buf_len) {
-			dev_err(dev->dev, "%s without data",
-					is_rdr ? "RDR" : "RRDY");
-			break;
-		}
-
 		w = omap_i2c_read_reg(dev, OMAP_I2C_DATA_REG);
 		*dev->buf++ = w;
 		dev->buf_len--;
@@ -794,10 +823,8 @@ static void omap_i2c_receive_data(struct omap_i2c_dev *dev, u8 num_bytes,
 		 * omap4 is 8 bit wide
 		 */
 		if (dev->flags & OMAP_I2C_FLAG_16BIT_DATA_REG) {
-			if (dev->buf_len) {
-				*dev->buf++ = w >> 8;
-				dev->buf_len--;
-			}
+			*dev->buf++ = w >> 8;
+			dev->buf_len--;
 		}
 	}
 }
@@ -808,12 +835,6 @@ static int omap_i2c_transmit_data(struct omap_i2c_dev *dev, u8 num_bytes,
 	u16		w;
 
 	while (num_bytes--) {
-		if (!dev->buf_len) {
-			dev_err(dev->dev, "%s without data",
-					is_xdr ? "XDR" : "XRDY");
-			break;
-		}
-
 		w = *dev->buf++;
 		dev->buf_len--;
 
@@ -822,10 +843,8 @@ static int omap_i2c_transmit_data(struct omap_i2c_dev *dev, u8 num_bytes,
 		 * omap4 is 8 bit wide
 		 */
 		if (dev->flags & OMAP_I2C_FLAG_16BIT_DATA_REG) {
-			if (dev->buf_len) {
-				w |= *dev->buf++ << 8;
-				dev->buf_len--;
-			}
+			w |= *dev->buf++ << 8;
+			dev->buf_len--;
 		}
 
 		if (dev->errata & I2C_OMAP_ERRATA_I462) {
@@ -923,8 +942,8 @@ complete:
 		if (stat & OMAP_I2C_STAT_RRDY) {
 			u8 num_bytes = 1;
 
-			if (dev->fifo_size)
-				num_bytes = dev->fifo_size;
+			if (dev->threshold)
+				num_bytes = dev->threshold;
 
 			omap_i2c_receive_data(dev, num_bytes, false);
 			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_RRDY);
@@ -953,8 +972,8 @@ complete:
 			u8 num_bytes = 1;
 			int ret;
 
-			if (dev->fifo_size)
-				num_bytes = dev->fifo_size;
+			if (dev->threshold)
+				num_bytes = dev->threshold;
 
 			ret = omap_i2c_transmit_data(dev, num_bytes, false);
 			stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);
-- 
1.7.5.4

[PATCHv3 17/17] i2c: omap: get rid of the "complete" label

[Shubhrajyoti D]

From: Felipe Balbi <balbi@ti.com>

we can ack stat and complete the command from
the errata handling itself.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
 drivers/i2c/busses/i2c-omap.c |   16 +++++++++++++---
 1 files changed, 13 insertions(+), 3 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index ac3bdae..bd8d282 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -794,6 +794,17 @@ static int errata_omap3_i462(struct omap_i2c_dev *dev)
 		if (stat & (OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) {
 			omap_i2c_ack_stat(dev, (OMAP_I2C_STAT_XRDY |
 							OMAP_I2C_STAT_XDR));
+			if (stat & OMAP_I2C_STAT_NACK) {
+				dev->cmd_err |= OMAP_I2C_STAT_NACK;
+				omap_i2c_ack_stat(dev, OMAP_I2C_STAT_NACK);
+			}
+
+			if (stat & OMAP_I2C_STAT_AL) {
+				dev_err(dev->dev, "Arbitration lost\n");
+				dev->cmd_err |= OMAP_I2C_STAT_AL;
+				omap_i2c_ack_stat(dev, OMAP_I2C_STAT_NACK);
+			}
+
 			return -EIO;
 		}
 
@@ -895,7 +906,6 @@ omap_i2c_isr(int this_irq, void *dev_id)
 			goto out;
 		}
 
-complete:
 		if (stat & OMAP_I2C_STAT_NACK) {
 			err |= OMAP_I2C_STAT_NACK;
 			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_NACK);
@@ -962,7 +972,7 @@ complete:
 			ret = omap_i2c_transmit_data(dev, num_bytes, true);
 			stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);
 			if (ret < 0)
-				goto complete;
+				goto out;
 
 			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_XDR);
 			continue;
@@ -978,7 +988,7 @@ complete:
 			ret = omap_i2c_transmit_data(dev, num_bytes, false);
 			stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);
 			if (ret < 0)
-				goto complete;
+				goto out;
 
 			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_XRDY);
 			continue;
-- 
1.7.5.4

[PATCHv3 06/17] i2c: omap: split out [XR]DR and [XR]RDY

[Felipe Balbi]

Hi,

On Fri, Jun 29, 2012 at 03:43:26PM +0530, Shubhrajyoti D wrote:
> From: Felipe Balbi <balbi@ti.com>
> 
> While they do pretty much the same thing, there
> are a few peculiarities. Specially WRT erratas,
> it's best to split those out and re-factor the
> read/write loop to another function which both
> cases call.
> 
> This last part will be done on another patch.
> 
> While at that, also avoid an unncessary register
> read since dev->fifo_len will always contain the
> correct amount of data to be transferred.

this statement isn't valid anymore, but I'd like it to be. See below

> Signed-off-by: Felipe Balbi <balbi@ti.com>
> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
> ---
>  drivers/i2c/busses/i2c-omap.c |  126 ++++++++++++++++++++++++++++++----------
>  1 files changed, 94 insertions(+), 32 deletions(-)
> 
> diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
> index 359ee08..45bd731 100644
> --- a/drivers/i2c/busses/i2c-omap.c
> +++ b/drivers/i2c/busses/i2c-omap.c
> @@ -820,36 +820,64 @@ complete:
>  			return IRQ_HANDLED;
>  		}
>  
> -		if (stat & (OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR)) {
> +		if (stat & OMAP_I2C_STAT_RDR) {
>  			u8 num_bytes = 1;
>  
> +			if (dev->fifo_size)
> +				num_bytes = (omap_i2c_read_reg(dev,
> +						OMAP_I2C_BUFSTAT_REG) >> 8)
> +						& 0x3F;

I wanted to avoid reading registers if we don't have to. This value will
be sitting in dev->buf_len.

-- 
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20120702/bd1ec352/attachment.sig>

[PATCHv3 17/17] i2c: omap: get rid of the "complete" label

[Felipe Balbi]

Hi,

On Fri, Jun 29, 2012 at 03:43:37PM +0530, Shubhrajyoti D wrote:
> @@ -962,7 +972,7 @@ complete:
>  			ret = omap_i2c_transmit_data(dev, num_bytes, true);
>  			stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);

this isn't needed anymore. please remove.

>  			if (ret < 0)
> -				goto complete;
> +				goto out;
>  
>  			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_XDR);
>  			continue;
> @@ -978,7 +988,7 @@ complete:
>  			ret = omap_i2c_transmit_data(dev, num_bytes, false);
>  			stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);

this isn't needed anymore. please remove.

-- 
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20120702/5cae2edd/attachment.sig>

[PATCHv3 06/17] i2c: omap: split out [XR]DR and [XR]RDY

[Shubhrajyoti Datta]

On Mon, Jul 2, 2012 at 5:26 PM, Felipe Balbi <balbi@ti.com> wrote:
> Hi,
>
> On Fri, Jun 29, 2012 at 03:43:26PM +0530, Shubhrajyoti D wrote:
>> From: Felipe Balbi <balbi@ti.com>
>>
>> While they do pretty much the same thing, there
>> are a few peculiarities. Specially WRT erratas,
>> it's best to split those out and re-factor the
>> read/write loop to another function which both
>> cases call.
>>
>> This last part will be done on another patch.
>>
>> While at that, also avoid an unncessary register
>> read since dev->fifo_len will always contain the
>> correct amount of data to be transferred.
>
> this statement isn't valid anymore, but I'd like it to be. See below
>
>> Signed-off-by: Felipe Balbi <balbi@ti.com>
>> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
>> ---
>>  drivers/i2c/busses/i2c-omap.c |  126 ++++++++++++++++++++++++++++++----------
>>  1 files changed, 94 insertions(+), 32 deletions(-)
>>
>> diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
>> index 359ee08..45bd731 100644
>> --- a/drivers/i2c/busses/i2c-omap.c
>> +++ b/drivers/i2c/busses/i2c-omap.c
>> @@ -820,36 +820,64 @@ complete:
>>                       return IRQ_HANDLED;
>>               }
>>
>> -             if (stat & (OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR)) {
>> +             if (stat & OMAP_I2C_STAT_RDR) {
>>                       u8 num_bytes = 1;
>>
>> +                     if (dev->fifo_size)
>> +                             num_bytes = (omap_i2c_read_reg(dev,
>> +                                             OMAP_I2C_BUFSTAT_REG) >> 8)
>> +                                             & 0x3F;
>
> I wanted to avoid reading registers if we don't have to. This value will
> be sitting in dev->buf_len.

Yes will fix this and resend.

>
> --
> balbi