* [PATCHv2 0/2] ARM: dts: Add new board dts file for Exynos3250-based Rinato board
@ 2014-10-07 22:45 Chanwoo Choi
2014-10-07 22:45 ` [PATCHv2 1/2] ARM: dts: Add " Chanwoo Choi
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: Chanwoo Choi @ 2014-10-07 22:45 UTC (permalink / raw)
To: linux-arm-kernel
This patchset adds new board dts file for Samsung Rinato board (Gear 2) which
is based on Exynos3250 SoC and adds sleep mode pin configuration using pinctrl
subsystem to reduce leakage power-consumption in sleep state.
This patchset is based on linux-samsung.git (for-next branch).
Changes from v1:
- Remove useless brace
- Remove unneeded 'regulators' keyword
- Consolidate memory information in one entry
Chanwoo Choi (2):
ARM: dts: Add board dts file for Exynos3250-based Rinato board
ARM: dts: Add sleep mode pin configuration for exynos3250-rinato
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/exynos3250-pinctrl.dtsi | 16 +
arch/arm/boot/dts/exynos3250-rinato.dts | 586 ++++++++++++++++++++++++++++++
3 files changed, 604 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/exynos3250-rinato.dts
--
1.8.0
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCHv2 1/2] ARM: dts: Add board dts file for Exynos3250-based Rinato board
2014-10-07 22:45 [PATCHv2 0/2] ARM: dts: Add new board dts file for Exynos3250-based Rinato board Chanwoo Choi
@ 2014-10-07 22:45 ` Chanwoo Choi
2014-10-07 22:45 ` [PATCHv2 2/2] ARM: dts: Add sleep mode pin configuration for exynos3250-rinato Chanwoo Choi
2014-10-13 5:00 ` [PATCHv2 0/2] ARM: dts: Add new board dts file for Exynos3250-based Rinato board Chanwoo Choi
2 siblings, 0 replies; 4+ messages in thread
From: Chanwoo Choi @ 2014-10-07 22:45 UTC (permalink / raw)
To: linux-arm-kernel
This patch add support for device tree sources for Samsung Rinato baord
(Gear 2) based on Exynos3250 SoC.
This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- MFC of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/exynos3250-rinato.dts | 432 ++++++++++++++++++++++++++++++++
2 files changed, 434 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/exynos3250-rinato.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b4f1fb1..5728918 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -64,7 +64,8 @@ dtb-$(CONFIG_ARCH_BRCMSTB) += \
dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \
da850-evm.dtb
dtb-$(CONFIG_ARCH_EFM32) += efm32gg-dk3750.dtb
-dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
+dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-rinato.dtb \
+ exynos4210-origen.dtb \
exynos4210-smdkv310.dtb \
exynos4210-trats.dtb \
exynos4210-universal_c210.dtb \
diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
new file mode 100644
index 0000000..af75ed7
--- /dev/null
+++ b/arch/arm/boot/dts/exynos3250-rinato.dts
@@ -0,0 +1,432 @@
+/*
+ * Samsung's Exynos3250 based Rinato board device tree source
+ *
+ * Copyright (c) 2014 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
+ * Device tree source file for Samsung's Rinato board which is based on
+ * Samsung Exynos3250 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include "exynos3250.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Samsung Rinato board";
+ compatible = "samsung,rinato", "samsung,exynos3250", "samsung,exynos3";
+
+ aliases {
+ i2c7 = &i2c_max77836;
+ };
+
+ memory {
+ reg = <0x40000000 0x1ff00000>;
+ };
+
+ chosen {
+ bootargs = "console=ttySAC1,115200N8 root=/dev/mmcblk0p15 rootwait earlyprintk panic=5";
+ };
+
+ firmware at 0205F000 {
+ compatible = "samsung,secure-firmware";
+ reg = <0x0205F000 0x1000>;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ power_key {
+ interrupt-parent = <&gpx2>;
+ interrupts = <7 0>;
+ gpios = <&gpx2 7 1>;
+ linux,code = <KEY_POWER>;
+ label = "power key";
+ debounce-interval = <10>;
+ gpio-key,wakeup;
+ };
+ };
+
+ vemmc_reg: voltage-regulator-0 {
+ compatible = "regulator-fixed";
+ regulator-name = "V_EMMC_2.8V-fixed";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ gpio = <&gpk0 2 0>;
+ enable-active-high;
+ };
+
+ i2c_max77836: i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ gpios = <&gpd0 2 0>, <&gpd0 3 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ max77836: subpmic at 25 {
+ compatible = "maxim,max77836";
+ interrupt-parent = <&gpx1>;
+ interrupts = <5 0>;
+ reg = <0x25>;
+ wakeup;
+
+ muic: max77836-muic {
+ compatible = "maxim,max77836-muic";
+ };
+
+ regulators {
+ compatible = "maxim,max77836-regulator";
+ safeout_reg: SAFEOUT {
+ regulator-name = "SAFEOUT";
+ };
+
+ charger_reg: CHARGER {
+ regulator-name = "CHARGER";
+ regulator-min-microamp = <45000>;
+ regulator-max-microamp = <475000>;
+ regulator-boot-on;
+ };
+
+ motor_reg: LDO1 {
+ regulator-name = "MOT_2.7V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ LDO2 {
+ regulator-name = "UNUSED_LDO2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ };
+ };
+
+ charger {
+ compatible = "maxim,max77836-charger";
+
+ maxim,constant-uvolt = <4350000>;
+ maxim,fast-charge-uamp = <225000>;
+ maxim,eoc-uamp = <7500>;
+ maxim,ovp-uvolt = <6500000>;
+ };
+ };
+ };
+};
+
+&adc {
+ vdd-supply = <&ldo3_reg>;
+ status = "okay";
+ assigned-clocks = <&cmu CLK_SCLK_TSADC>;
+ assigned-clock-rates = <6000000>;
+
+ thermistor-ap {
+ compatible = "ntc,ncp15wb473";
+ pullup-uv = <1800000>;
+ pullup-ohm = <100000>;
+ pulldown-ohm = <100000>;
+ io-channels = <&adc 0>;
+ };
+
+ thermistor-battery {
+ compatible = "ntc,ncp15wb473";
+ pullup-uv = <1800000>;
+ pullup-ohm = <100000>;
+ pulldown-ohm = <100000>;
+ io-channels = <&adc 1>;
+ };
+};
+
+&i2c_0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <100000>;
+ status = "okay";
+
+ s2mps14_pmic at 66 {
+ compatible = "samsung,s2mps14-pmic";
+ interrupt-parent = <&gpx0>;
+ interrupts = <7 0>;
+ reg = <0x66>;
+ wakeup;
+
+ s2mps14_osc: clocks {
+ compatible = "samsung,s2mps14-clk";
+ #clock-cells = <1>;
+ clock-output-names = "s2mps14_ap", "unused",
+ "s2mps14_bt";
+ };
+
+ regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VAP_ALIVE_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "VAP_M1_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "VCC_AP_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "VAP_AVDD_PLL1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "VAP_PLL_ISO_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "VAP_VMIPI_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "VAP_AVDD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "VAP_USB_3.0V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "V_LPDDR_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "UNUSED_LDO10";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "V_EMMC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ samsung,ext-control-gpios = <&gpk0 2 0>;
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "V_EMMC_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ samsung,ext-control-gpios = <&gpk0 2 0>;
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "CAM_AVDD_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "UNUSED_LDO14";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "TSP_AVDD_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "LCD_VDD_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "V_IRLED_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo18_reg: LDO18 {
+ regulator-name = "CAM_AF_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo19_reg: LDO19 {
+ regulator-name = "TSP_VDD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo20_reg: LDO20 {
+ regulator-name = "LCD_VDD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo21_reg: LDO21 {
+ regulator-name = "CAM_IO_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo22_reg: LDO22 {
+ regulator-name = "CAM_DVDD_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ ldo23_reg: LDO23 {
+ regulator-name = "HRM_VCC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo24_reg: LDO24 {
+ regulator-name = "HRM_VCC_3.3V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ ldo25_reg: LDO25 {
+ regulator-name = "UNUSED_LDO25";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "VAP_MIF_1.0V";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <900000>;
+ regulator-always-on;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "VAP_ARM_1.0V";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-always-on;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "VAP_INT3D_1.0V";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "VCC_SUB_1.95V";
+ regulator-min-microvolt = <1950000>;
+ regulator-max-microvolt = <1950000>;
+ regulator-always-on;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "VCC_SUB_1.35V";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&i2c_1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <400000>;
+ status = "okay";
+
+ fuelgauge at 36 {
+ compatible = "maxim,max77836-battery";
+ interrupt-parent = <&gpx1>;
+ interrupts = <2 8>;
+ reg = <0x36>;
+ };
+};
+
+&i2s2 {
+ status = "okay";
+};
+
+&mfc {
+ status = "okay";
+};
+
+&mshc_0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ num-slots = <1>;
+ broken-cd;
+ non-removable;
+ cap-mmc-highspeed;
+ desc-num = <4>;
+ mmc-hs200-1_8v;
+ card-detect-delay = <200>;
+ vmmc-supply = <&vemmc_reg>;
+ clock-frequency = <100000000>;
+ clock-freq-min-max = <400000 100000000>;
+ samsung,dw-mshc-ciu-div = <1>;
+ samsung,dw-mshc-sdr-timing = <0 1>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&serial_0 {
+ assigned-clocks = <&cmu CLK_SCLK_UART0>;
+ assigned-clock-rates = <100000000>;
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&tmu {
+ vtmu-supply = <&ldo7_reg>;
+ status = "okay";
+};
+
+&rtc {
+ clocks = <&cmu CLK_RTC>, <&s2mps14_osc 0>;
+ clock-names = "rtc", "rtc_src";
+ status = "okay";
+};
+
+&xusbxti {
+ clock-frequency = <24000000>;
+};
--
1.8.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCHv2 2/2] ARM: dts: Add sleep mode pin configuration for exynos3250-rinato
2014-10-07 22:45 [PATCHv2 0/2] ARM: dts: Add new board dts file for Exynos3250-based Rinato board Chanwoo Choi
2014-10-07 22:45 ` [PATCHv2 1/2] ARM: dts: Add " Chanwoo Choi
@ 2014-10-07 22:45 ` Chanwoo Choi
2014-10-13 5:00 ` [PATCHv2 0/2] ARM: dts: Add new board dts file for Exynos3250-based Rinato board Chanwoo Choi
2 siblings, 0 replies; 4+ messages in thread
From: Chanwoo Choi @ 2014-10-07 22:45 UTC (permalink / raw)
To: linux-arm-kernel
This patch add sleep mode pin configuration using pinctrl subsystem
to reduce leakage power-consumption of gpio pin in sleep state.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <Kyungmin Park@samsung.com>
---
arch/arm/boot/dts/exynos3250-pinctrl.dtsi | 16 ++++
arch/arm/boot/dts/exynos3250-rinato.dts | 154 ++++++++++++++++++++++++++++++
2 files changed, 170 insertions(+)
diff --git a/arch/arm/boot/dts/exynos3250-pinctrl.dtsi b/arch/arm/boot/dts/exynos3250-pinctrl.dtsi
index 47b92c1..5ab81c3 100644
--- a/arch/arm/boot/dts/exynos3250-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos3250-pinctrl.dtsi
@@ -12,6 +12,22 @@
* published by the Free Software Foundation.
*/
+#define PIN_PULL_NONE 0
+#define PIN_PULL_DOWN 1
+#define PIN_PULL_UP 3
+
+#define PIN_PDN_OUT0 0
+#define PIN_PDN_OUT1 1
+#define PIN_PDN_INPUT 2
+#define PIN_PDN_PREV 3
+
+#define PIN_SLP(_pin, _mode, _pull) \
+ _pin { \
+ samsung,pins = #_pin; \
+ samsung,pin-con-pdn = <PIN_PDN_ ##_mode>; \
+ samsung,pin-pud-pdn = <PIN_PULL_ ##_pull>; \
+ }
+
&pinctrl_0 {
gpa0: gpa0 {
gpio-controller;
diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
index af75ed7..63861e7 100644
--- a/arch/arm/boot/dts/exynos3250-rinato.dts
+++ b/arch/arm/boot/dts/exynos3250-rinato.dts
@@ -430,3 +430,157 @@
&xusbxti {
clock-frequency = <24000000>;
};
+
+&pinctrl_0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sleep0>;
+
+ sleep0: sleep-state {
+ PIN_SLP(gpa0-0, INPUT, DOWN);
+ PIN_SLP(gpa0-1, INPUT, DOWN);
+ PIN_SLP(gpa0-2, INPUT, DOWN);
+ PIN_SLP(gpa0-3, INPUT, DOWN);
+ PIN_SLP(gpa0-4, INPUT, DOWN);
+ PIN_SLP(gpa0-5, INPUT, DOWN);
+ PIN_SLP(gpa0-6, INPUT, DOWN);
+ PIN_SLP(gpa0-7, INPUT, DOWN);
+
+ PIN_SLP(gpa1-0, INPUT, DOWN);
+ PIN_SLP(gpa1-1, INPUT, DOWN);
+ PIN_SLP(gpa1-2, INPUT, DOWN);
+ PIN_SLP(gpa1-3, INPUT, DOWN);
+ PIN_SLP(gpa1-4, INPUT, DOWN);
+ PIN_SLP(gpa1-5, INPUT, DOWN);
+
+ PIN_SLP(gpb-0, PREV, NONE);
+ PIN_SLP(gpb-1, PREV, NONE);
+ PIN_SLP(gpb-2, PREV, NONE);
+ PIN_SLP(gpb-3, PREV, NONE);
+ PIN_SLP(gpb-4, INPUT, DOWN);
+ PIN_SLP(gpb-5, INPUT, DOWN);
+ PIN_SLP(gpb-6, INPUT, DOWN);
+ PIN_SLP(gpb-7, INPUT, DOWN);
+
+ PIN_SLP(gpc0-0, INPUT, DOWN);
+ PIN_SLP(gpc0-1, INPUT, DOWN);
+ PIN_SLP(gpc0-2, INPUT, DOWN);
+ PIN_SLP(gpc0-3, INPUT, DOWN);
+ PIN_SLP(gpc0-4, INPUT, DOWN);
+
+ PIN_SLP(gpc1-0, INPUT, DOWN);
+ PIN_SLP(gpc1-1, INPUT, DOWN);
+ PIN_SLP(gpc1-2, INPUT, DOWN);
+ PIN_SLP(gpc1-3, INPUT, DOWN);
+ PIN_SLP(gpc1-4, INPUT, DOWN);
+
+ PIN_SLP(gpd0-0, INPUT, DOWN);
+ PIN_SLP(gpd0-1, INPUT, DOWN);
+ PIN_SLP(gpd0-2, INPUT, NONE);
+ PIN_SLP(gpd0-3, INPUT, NONE);
+
+ PIN_SLP(gpd1-0, INPUT, NONE);
+ PIN_SLP(gpd1-1, INPUT, NONE);
+ PIN_SLP(gpd1-2, INPUT, NONE);
+ PIN_SLP(gpd1-3, INPUT, NONE);
+ };
+};
+
+&pinctrl_1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sleep1>;
+
+ sleep1: sleep-state {
+ PIN_SLP(gpe0-0, PREV, NONE);
+ PIN_SLP(gpe0-1, PREV, NONE);
+ PIN_SLP(gpe0-2, INPUT, DOWN);
+ PIN_SLP(gpe0-3, INPUT, DOWN);
+ PIN_SLP(gpe0-4, INPUT, DOWN);
+ PIN_SLP(gpe0-5, INPUT, DOWN);
+ PIN_SLP(gpe0-6, INPUT, DOWN);
+ PIN_SLP(gpe0-7, INPUT, DOWN);
+
+ PIN_SLP(gpe1-0, INPUT, DOWN);
+ PIN_SLP(gpe1-1, PREV, NONE);
+ PIN_SLP(gpe1-2, INPUT, DOWN);
+ PIN_SLP(gpe1-3, INPUT, DOWN);
+ PIN_SLP(gpe1-4, INPUT, DOWN);
+ PIN_SLP(gpe1-5, INPUT, DOWN);
+ PIN_SLP(gpe1-6, INPUT, DOWN);
+ PIN_SLP(gpe1-7, INPUT, NONE);
+
+ PIN_SLP(gpe2-0, INPUT, NONE);
+ PIN_SLP(gpe2-1, INPUT, NONE);
+ PIN_SLP(gpe2-2, INPUT, NONE);
+
+ PIN_SLP(gpk0-0, INPUT, DOWN);
+ PIN_SLP(gpk0-1, INPUT, DOWN);
+ PIN_SLP(gpk0-2, OUT0, NONE);
+ PIN_SLP(gpk0-3, INPUT, DOWN);
+ PIN_SLP(gpk0-4, INPUT, DOWN);
+ PIN_SLP(gpk0-5, INPUT, DOWN);
+ PIN_SLP(gpk0-6, INPUT, DOWN);
+ PIN_SLP(gpk0-7, INPUT, DOWN);
+
+ PIN_SLP(gpk1-0, INPUT, DOWN);
+ PIN_SLP(gpk1-1, INPUT, DOWN);
+ PIN_SLP(gpk1-2, INPUT, DOWN);
+ PIN_SLP(gpk1-3, INPUT, DOWN);
+ PIN_SLP(gpk1-4, INPUT, DOWN);
+ PIN_SLP(gpk1-5, INPUT, DOWN);
+ PIN_SLP(gpk1-6, INPUT, DOWN);
+
+ PIN_SLP(gpk2-0, INPUT, DOWN);
+ PIN_SLP(gpk2-1, INPUT, DOWN);
+ PIN_SLP(gpk2-2, INPUT, DOWN);
+ PIN_SLP(gpk2-3, INPUT, DOWN);
+ PIN_SLP(gpk2-4, INPUT, DOWN);
+ PIN_SLP(gpk2-5, INPUT, DOWN);
+ PIN_SLP(gpk2-6, INPUT, DOWN);
+
+ PIN_SLP(gpl0-0, INPUT, DOWN);
+ PIN_SLP(gpl0-1, INPUT, DOWN);
+ PIN_SLP(gpl0-2, INPUT, DOWN);
+ PIN_SLP(gpl0-3, INPUT, DOWN);
+
+ PIN_SLP(gpm0-0, INPUT, DOWN);
+ PIN_SLP(gpm0-1, INPUT, DOWN);
+ PIN_SLP(gpm0-2, INPUT, DOWN);
+ PIN_SLP(gpm0-3, INPUT, DOWN);
+ PIN_SLP(gpm0-4, INPUT, DOWN);
+ PIN_SLP(gpm0-5, INPUT, DOWN);
+ PIN_SLP(gpm0-6, INPUT, DOWN);
+ PIN_SLP(gpm0-7, INPUT, DOWN);
+
+ PIN_SLP(gpm1-0, INPUT, DOWN);
+ PIN_SLP(gpm1-1, INPUT, DOWN);
+ PIN_SLP(gpm1-2, INPUT, DOWN);
+ PIN_SLP(gpm1-3, INPUT, DOWN);
+ PIN_SLP(gpm1-4, INPUT, DOWN);
+ PIN_SLP(gpm1-5, INPUT, DOWN);
+ PIN_SLP(gpm1-6, INPUT, DOWN);
+
+ PIN_SLP(gpm2-0, INPUT, DOWN);
+ PIN_SLP(gpm2-1, INPUT, DOWN);
+ PIN_SLP(gpm2-2, INPUT, DOWN);
+ PIN_SLP(gpm2-3, INPUT, DOWN);
+ PIN_SLP(gpm2-4, INPUT, DOWN);
+
+ PIN_SLP(gpm3-0, INPUT, DOWN);
+ PIN_SLP(gpm3-1, INPUT, DOWN);
+ PIN_SLP(gpm3-2, INPUT, DOWN);
+ PIN_SLP(gpm3-3, INPUT, DOWN);
+ PIN_SLP(gpm3-4, INPUT, DOWN);
+ PIN_SLP(gpm3-5, INPUT, DOWN);
+ PIN_SLP(gpm3-6, INPUT, DOWN);
+ PIN_SLP(gpm3-7, INPUT, DOWN);
+
+ PIN_SLP(gpm4-0, INPUT, DOWN);
+ PIN_SLP(gpm4-1, INPUT, DOWN);
+ PIN_SLP(gpm4-2, INPUT, DOWN);
+ PIN_SLP(gpm4-3, INPUT, DOWN);
+ PIN_SLP(gpm4-4, INPUT, DOWN);
+ PIN_SLP(gpm4-5, INPUT, DOWN);
+ PIN_SLP(gpm4-6, INPUT, DOWN);
+ PIN_SLP(gpm4-7, INPUT, DOWN);
+ };
+};
--
1.8.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCHv2 0/2] ARM: dts: Add new board dts file for Exynos3250-based Rinato board
2014-10-07 22:45 [PATCHv2 0/2] ARM: dts: Add new board dts file for Exynos3250-based Rinato board Chanwoo Choi
2014-10-07 22:45 ` [PATCHv2 1/2] ARM: dts: Add " Chanwoo Choi
2014-10-07 22:45 ` [PATCHv2 2/2] ARM: dts: Add sleep mode pin configuration for exynos3250-rinato Chanwoo Choi
@ 2014-10-13 5:00 ` Chanwoo Choi
2 siblings, 0 replies; 4+ messages in thread
From: Chanwoo Choi @ 2014-10-13 5:00 UTC (permalink / raw)
To: linux-arm-kernel
Dear Kukjin,
Could you please review this patchset?
Best Regards,
Chanwoo Choi
On 10/08/2014 07:45 AM, Chanwoo Choi wrote:
> This patchset adds new board dts file for Samsung Rinato board (Gear 2) which
> is based on Exynos3250 SoC and adds sleep mode pin configuration using pinctrl
> subsystem to reduce leakage power-consumption in sleep state.
>
> This patchset is based on linux-samsung.git (for-next branch).
>
> Changes from v1:
> - Remove useless brace
> - Remove unneeded 'regulators' keyword
> - Consolidate memory information in one entry
>
> Chanwoo Choi (2):
> ARM: dts: Add board dts file for Exynos3250-based Rinato board
> ARM: dts: Add sleep mode pin configuration for exynos3250-rinato
>
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/exynos3250-pinctrl.dtsi | 16 +
> arch/arm/boot/dts/exynos3250-rinato.dts | 586 ++++++++++++++++++++++++++++++
> 3 files changed, 604 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/exynos3250-rinato.dts
>
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2014-10-13 5:00 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-10-07 22:45 [PATCHv2 0/2] ARM: dts: Add new board dts file for Exynos3250-based Rinato board Chanwoo Choi
2014-10-07 22:45 ` [PATCHv2 1/2] ARM: dts: Add " Chanwoo Choi
2014-10-07 22:45 ` [PATCHv2 2/2] ARM: dts: Add sleep mode pin configuration for exynos3250-rinato Chanwoo Choi
2014-10-13 5:00 ` [PATCHv2 0/2] ARM: dts: Add new board dts file for Exynos3250-based Rinato board Chanwoo Choi
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).