* [PATCH] Mediatek PMIC wrapper support
@ 2015-02-22 12:02 Sascha Hauer
2015-02-22 12:02 ` [PATCH 1/2] soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs Sascha Hauer
` (2 more replies)
0 siblings, 3 replies; 8+ messages in thread
From: Sascha Hauer @ 2015-02-22 12:02 UTC (permalink / raw)
To: linux-arm-kernel
This series adds support for the PMIC wrapper found on MT8135 and
MT8173 SoCs. This has been sent several times already as part of
different series, this time broken out as a series only containing
the wrapper code. No further compile time dependencies.
Matthias, I assume you can take this one through your tree, right?
Sascha
^ permalink raw reply [flat|nested] 8+ messages in thread* [PATCH 1/2] soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs 2015-02-22 12:02 [PATCH] Mediatek PMIC wrapper support Sascha Hauer @ 2015-02-22 12:02 ` Sascha Hauer 2015-03-09 8:53 ` Matthias Brugger 2015-02-22 12:02 ` [PATCH 2/2] dt-bindings: ARM: Mediatek: document binding for the PMIC wrapper Sascha Hauer 2015-03-09 5:37 ` [PATCH] Mediatek PMIC wrapper support Sascha Hauer 2 siblings, 1 reply; 8+ messages in thread From: Sascha Hauer @ 2015-02-22 12:02 UTC (permalink / raw) To: linux-arm-kernel From: Flora Fu <flora.fu@mediatek.com> This adds support for the PMIC wrapper found on MediaTek MT8135 and MT8173 SoCs. On MediaTek MT8135, MT8173 and other SoCs the PMIC is connected via SPI. The SPI master interface is not directly visible to the CPU, but only through the PMIC wrapper inside the SoC. The communication between the SoC and the PMIC can optionally be encrypted. Also a non standard Dual IO SPI mode can be used to increase speed. The MT8135 also supports a special feature named "IP Pairing". With IP Pairing the pins of some SoC internal peripherals can be on the PMIC. The signals of these pins are routed over the SPI bus using the pwrap bridge. Because of these optional non SPI conform features the PMIC driver is not implemented as a SPI bus master driver. Signed-off-by: Flora Fu, MediaTek Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> --- drivers/soc/Kconfig | 1 + drivers/soc/Makefile | 1 + drivers/soc/mediatek/Kconfig | 11 + drivers/soc/mediatek/Makefile | 1 + drivers/soc/mediatek/mtk-pmic-wrap.c | 1027 ++++++++++++++++++++++++++++++++++ 5 files changed, 1041 insertions(+) create mode 100644 drivers/soc/mediatek/Kconfig create mode 100644 drivers/soc/mediatek/Makefile create mode 100644 drivers/soc/mediatek/mtk-pmic-wrap.c diff --git a/drivers/soc/Kconfig b/drivers/soc/Kconfig index 76d6bd4..d8bde82f0 100644 --- a/drivers/soc/Kconfig +++ b/drivers/soc/Kconfig @@ -1,5 +1,6 @@ menu "SOC (System On Chip) specific Drivers" +source "drivers/soc/mediatek/Kconfig" source "drivers/soc/qcom/Kconfig" source "drivers/soc/ti/Kconfig" source "drivers/soc/versatile/Kconfig" diff --git a/drivers/soc/Makefile b/drivers/soc/Makefile index 063113d..70042b2 100644 --- a/drivers/soc/Makefile +++ b/drivers/soc/Makefile @@ -2,6 +2,7 @@ # Makefile for the Linux Kernel SOC specific device drivers. # +obj-$(CONFIG_ARCH_MEDIATEK) += mediatek/ obj-$(CONFIG_ARCH_QCOM) += qcom/ obj-$(CONFIG_ARCH_TEGRA) += tegra/ obj-$(CONFIG_SOC_TI) += ti/ diff --git a/drivers/soc/mediatek/Kconfig b/drivers/soc/mediatek/Kconfig new file mode 100644 index 0000000..b91665a --- /dev/null +++ b/drivers/soc/mediatek/Kconfig @@ -0,0 +1,11 @@ +# +# MediaTek SoC drivers +# +config MTK_PMIC_WRAP + tristate "MediaTek PMIC Wrapper Support" + depends on ARCH_MEDIATEK + select REGMAP + help + Say yes here to add support for MediaTek PMIC Wrapper found + on the MT8135 and MT8173 SoCs. The PMIC wrapper is a proprietary + hardware to connect the PMIC. diff --git a/drivers/soc/mediatek/Makefile b/drivers/soc/mediatek/Makefile new file mode 100644 index 0000000..ecaf4de --- /dev/null +++ b/drivers/soc/mediatek/Makefile @@ -0,0 +1 @@ +obj-$(CONFIG_MTK_PMIC_WRAP) += mtk-pmic-wrap.o diff --git a/drivers/soc/mediatek/mtk-pmic-wrap.c b/drivers/soc/mediatek/mtk-pmic-wrap.c new file mode 100644 index 0000000..bd1f881 --- /dev/null +++ b/drivers/soc/mediatek/mtk-pmic-wrap.c @@ -0,0 +1,1027 @@ +/* + * Copyright (c) 2014 MediaTek Inc. + * Author: Flora Fu, MediaTek + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +#define DEBUG +#include <linux/clk.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/reset.h> + +#define PWRAP_MT8135_BRIDGE_IORD_ARB_EN 0x4 +#define PWRAP_MT8135_BRIDGE_WACS3_EN 0x10 +#define PWRAP_MT8135_BRIDGE_INIT_DONE3 0x14 +#define PWRAP_MT8135_BRIDGE_WACS4_EN 0x24 +#define PWRAP_MT8135_BRIDGE_INIT_DONE4 0x28 +#define PWRAP_MT8135_BRIDGE_INT_EN 0x38 +#define PWRAP_MT8135_BRIDGE_TIMER_EN 0x48 +#define PWRAP_MT8135_BRIDGE_WDT_UNIT 0x50 +#define PWRAP_MT8135_BRIDGE_WDT_SRC_EN 0x54 + +/* macro for wrapper status */ +#define PWRAP_GET_WACS_RDATA(x) (((x) >> 0) & 0x0000ffff) +#define PWRAP_GET_WACS_FSM(x) (((x) >> 16) & 0x00000007) +#define PWRAP_GET_WACS_REQ(x) (((x) >> 19) & 0x00000001) +#define PWRAP_STATE_SYNC_IDLE0 (1 << 20) +#define PWRAP_STATE_INIT_DONE0 (1 << 21) + +/* macro for WACS FSM */ +#define PWRAP_WACS_FSM_IDLE 0x00 +#define PWRAP_WACS_FSM_REQ 0x02 +#define PWRAP_WACS_FSM_WFDLE 0x04 +#define PWRAP_WACS_FSM_WFVLDCLR 0x06 +#define PWRAP_WACS_INIT_DONE 0x01 +#define PWRAP_WACS_WACS_SYNC_IDLE 0x01 +#define PWRAP_WACS_SYNC_BUSY 0x00 + +/* macro for device wrapper default value */ +#define PWRAP_DEW_READ_TEST_VAL 0x5aa5 +#define PWRAP_DEW_WRITE_TEST_VAL 0xa55a + +/* macro for manual command */ +#define PWRAP_MAN_CMD_SPI_WRITE (1 << 13) +#define PWRAP_MAN_CMD_OP_CSH (0x0 << 8) +#define PWRAP_MAN_CMD_OP_CSL (0x1 << 8) +#define PWRAP_MAN_CMD_OP_CK (0x2 << 8) +#define PWRAP_MAN_CMD_OP_OUTS (0x8 << 8) +#define PWRAP_MAN_CMD_OP_OUTD (0x9 << 8) +#define PWRAP_MAN_CMD_OP_OUTQ (0xa << 8) + +/* macro for slave device wrapper registers */ +#define PWRAP_DEW_BASE 0xbc00 +#define PWRAP_DEW_EVENT_OUT_EN (PWRAP_DEW_BASE + 0x0) +#define PWRAP_DEW_DIO_EN (PWRAP_DEW_BASE + 0x2) +#define PWRAP_DEW_EVENT_SRC_EN (PWRAP_DEW_BASE + 0x4) +#define PWRAP_DEW_EVENT_SRC (PWRAP_DEW_BASE + 0x6) +#define PWRAP_DEW_EVENT_FLAG (PWRAP_DEW_BASE + 0x8) +#define PWRAP_DEW_READ_TEST (PWRAP_DEW_BASE + 0xa) +#define PWRAP_DEW_WRITE_TEST (PWRAP_DEW_BASE + 0xc) +#define PWRAP_DEW_CRC_EN (PWRAP_DEW_BASE + 0xe) +#define PWRAP_DEW_CRC_VAL (PWRAP_DEW_BASE + 0x10) +#define PWRAP_DEW_MON_GRP_SEL (PWRAP_DEW_BASE + 0x12) +#define PWRAP_DEW_MON_FLAG_SEL (PWRAP_DEW_BASE + 0x14) +#define PWRAP_DEW_EVENT_TEST (PWRAP_DEW_BASE + 0x16) +#define PWRAP_DEW_CIPHER_KEY_SEL (PWRAP_DEW_BASE + 0x18) +#define PWRAP_DEW_CIPHER_IV_SEL (PWRAP_DEW_BASE + 0x1a) +#define PWRAP_DEW_CIPHER_LOAD (PWRAP_DEW_BASE + 0x1c) +#define PWRAP_DEW_CIPHER_START (PWRAP_DEW_BASE + 0x1e) +#define PWRAP_DEW_CIPHER_RDY (PWRAP_DEW_BASE + 0x20) +#define PWRAP_DEW_CIPHER_MODE (PWRAP_DEW_BASE + 0x22) +#define PWRAP_DEW_CIPHER_SWRST (PWRAP_DEW_BASE + 0x24) +#define PWRAP_MT8173_DEW_CIPHER_IV0 (PWRAP_DEW_BASE + 0x26) +#define PWRAP_MT8173_DEW_CIPHER_IV1 (PWRAP_DEW_BASE + 0x28) +#define PWRAP_MT8173_DEW_CIPHER_IV2 (PWRAP_DEW_BASE + 0x2a) +#define PWRAP_MT8173_DEW_CIPHER_IV3 (PWRAP_DEW_BASE + 0x2c) +#define PWRAP_MT8173_DEW_CIPHER_IV4 (PWRAP_DEW_BASE + 0x2e) +#define PWRAP_MT8173_DEW_CIPHER_IV5 (PWRAP_DEW_BASE + 0x30) + +/* + * FIXME: These shouldn't be here. These registers are on the PMIC, + * so they should be touched in the PMIC driver, not the driver + * granting access to it. + */ +#define MT6397_WRP_CKPDN 0x011a +#define MT6397_WRP_RST_CON 0x0120 +#define MT6397_TOP_CKCON2 0x012a +#define MT6397_TOP_CKCON3 0x01d4 + +enum pwrap_regs { + PWRAP_MUX_SEL, + PWRAP_WRAP_EN, + PWRAP_DIO_EN, + PWRAP_SIDLY, + PWRAP_CSHEXT_WRITE, + PWRAP_CSHEXT_READ, + PWRAP_CSLEXT_START, + PWRAP_CSLEXT_END, + PWRAP_STAUPD_PRD, + PWRAP_STAUPD_GRPEN, + PWRAP_STAUPD_MAN_TRIG, + PWRAP_STAUPD_STA, + PWRAP_WRAP_STA, + PWRAP_HARB_INIT, + PWRAP_HARB_HPRIO, + PWRAP_HIPRIO_ARB_EN, + PWRAP_HARB_STA0, + PWRAP_HARB_STA1, + PWRAP_MAN_EN, + PWRAP_MAN_CMD, + PWRAP_MAN_RDATA, + PWRAP_MAN_VLDCLR, + PWRAP_WACS0_EN, + PWRAP_INIT_DONE0, + PWRAP_WACS0_CMD, + PWRAP_WACS0_RDATA, + PWRAP_WACS0_VLDCLR, + PWRAP_WACS1_EN, + PWRAP_INIT_DONE1, + PWRAP_WACS1_CMD, + PWRAP_WACS1_RDATA, + PWRAP_WACS1_VLDCLR, + PWRAP_WACS2_EN, + PWRAP_INIT_DONE2, + PWRAP_WACS2_CMD, + PWRAP_WACS2_RDATA, + PWRAP_WACS2_VLDCLR, + PWRAP_INT_EN, + PWRAP_INT_FLG_RAW, + PWRAP_INT_FLG, + PWRAP_INT_CLR, + PWRAP_SIG_ADR, + PWRAP_SIG_MODE, + PWRAP_SIG_VALUE, + PWRAP_SIG_ERRVAL, + PWRAP_CRC_EN, + PWRAP_TIMER_EN, + PWRAP_TIMER_STA, + PWRAP_WDT_UNIT, + PWRAP_WDT_SRC_EN, + PWRAP_WDT_FLG, + PWRAP_DEBUG_INT_SEL, + PWRAP_CIPHER_KEY_SEL, + PWRAP_CIPHER_IV_SEL, + PWRAP_CIPHER_RDY, + PWRAP_CIPHER_MODE, + PWRAP_CIPHER_SWRST, + PWRAP_DCM_EN, + PWRAP_DCM_DBC_PRD, + + /* MT8135 only regs */ + PWRAP_CSHEXT, + PWRAP_EVENT_IN_EN, + PWRAP_EVENT_DST_EN, + PWRAP_RRARB_INIT, + PWRAP_RRARB_EN, + PWRAP_RRARB_STA0, + PWRAP_RRARB_STA1, + PWRAP_EVENT_STA, + PWRAP_EVENT_STACLR, + PWRAP_CIPHER_LOAD, + PWRAP_CIPHER_START, + + /* MT8173 only regs */ + PWRAP_RDDMY, + PWRAP_SI_CK_CON, + PWRAP_DVFS_ADR0, + PWRAP_DVFS_WDATA0, + PWRAP_DVFS_ADR1, + PWRAP_DVFS_WDATA1, + PWRAP_DVFS_ADR2, + PWRAP_DVFS_WDATA2, + PWRAP_DVFS_ADR3, + PWRAP_DVFS_WDATA3, + PWRAP_DVFS_ADR4, + PWRAP_DVFS_WDATA4, + PWRAP_DVFS_ADR5, + PWRAP_DVFS_WDATA5, + PWRAP_DVFS_ADR6, + PWRAP_DVFS_WDATA6, + PWRAP_DVFS_ADR7, + PWRAP_DVFS_WDATA7, + PWRAP_SPMINF_STA, + PWRAP_CIPHER_EN, +}; + +static int mt8173_regs[] = { + [PWRAP_MUX_SEL] = 0x0, + [PWRAP_WRAP_EN] = 0x4, + [PWRAP_DIO_EN] = 0x8, + [PWRAP_SIDLY] = 0xc, + [PWRAP_RDDMY] = 0x10, + [PWRAP_SI_CK_CON] = 0x14, + [PWRAP_CSHEXT_WRITE] = 0x18, + [PWRAP_CSHEXT_READ] = 0x1c, + [PWRAP_CSLEXT_START] = 0x20, + [PWRAP_CSLEXT_END] = 0x24, + [PWRAP_STAUPD_PRD] = 0x28, + [PWRAP_STAUPD_GRPEN] = 0x2c, + [PWRAP_STAUPD_MAN_TRIG] = 0x40, + [PWRAP_STAUPD_STA] = 0x44, + [PWRAP_WRAP_STA] = 0x48, + [PWRAP_HARB_INIT] = 0x4c, + [PWRAP_HARB_HPRIO] = 0x50, + [PWRAP_HIPRIO_ARB_EN] = 0x54, + [PWRAP_HARB_STA0] = 0x58, + [PWRAP_HARB_STA1] = 0x5c, + [PWRAP_MAN_EN] = 0x60, + [PWRAP_MAN_CMD] = 0x64, + [PWRAP_MAN_RDATA] = 0x68, + [PWRAP_MAN_VLDCLR] = 0x6c, + [PWRAP_WACS0_EN] = 0x70, + [PWRAP_INIT_DONE0] = 0x74, + [PWRAP_WACS0_CMD] = 0x78, + [PWRAP_WACS0_RDATA] = 0x7c, + [PWRAP_WACS0_VLDCLR] = 0x80, + [PWRAP_WACS1_EN] = 0x84, + [PWRAP_INIT_DONE1] = 0x88, + [PWRAP_WACS1_CMD] = 0x8c, + [PWRAP_WACS1_RDATA] = 0x90, + [PWRAP_WACS1_VLDCLR] = 0x94, + [PWRAP_WACS2_EN] = 0x98, + [PWRAP_INIT_DONE2] = 0x9c, + [PWRAP_WACS2_CMD] = 0xa0, + [PWRAP_WACS2_RDATA] = 0xa4, + [PWRAP_WACS2_VLDCLR] = 0xa8, + [PWRAP_INT_EN] = 0xac, + [PWRAP_INT_FLG_RAW] = 0xb0, + [PWRAP_INT_FLG] = 0xb4, + [PWRAP_INT_CLR] = 0xb8, + [PWRAP_SIG_ADR] = 0xbc, + [PWRAP_SIG_MODE] = 0xc0, + [PWRAP_SIG_VALUE] = 0xc4, + [PWRAP_SIG_ERRVAL] = 0xc8, + [PWRAP_CRC_EN] = 0xcc, + [PWRAP_TIMER_EN] = 0xd0, + [PWRAP_TIMER_STA] = 0xd4, + [PWRAP_WDT_UNIT] = 0xd8, + [PWRAP_WDT_SRC_EN] = 0xdc, + [PWRAP_WDT_FLG] = 0xe0, + [PWRAP_DEBUG_INT_SEL] = 0xe4, + [PWRAP_DVFS_ADR0] = 0xe8, + [PWRAP_DVFS_WDATA0] = 0xec, + [PWRAP_DVFS_ADR1] = 0xf0, + [PWRAP_DVFS_WDATA1] = 0xf4, + [PWRAP_DVFS_ADR2] = 0xf8, + [PWRAP_DVFS_WDATA2] = 0xfc, + [PWRAP_DVFS_ADR3] = 0x100, + [PWRAP_DVFS_WDATA3] = 0x104, + [PWRAP_DVFS_ADR4] = 0x108, + [PWRAP_DVFS_WDATA4] = 0x10c, + [PWRAP_DVFS_ADR5] = 0x110, + [PWRAP_DVFS_WDATA5] = 0x114, + [PWRAP_DVFS_ADR6] = 0x118, + [PWRAP_DVFS_WDATA6] = 0x11c, + [PWRAP_DVFS_ADR7] = 0x120, + [PWRAP_DVFS_WDATA7] = 0x124, + [PWRAP_SPMINF_STA] = 0x128, + [PWRAP_CIPHER_KEY_SEL] = 0x12c, + [PWRAP_CIPHER_IV_SEL] = 0x130, + [PWRAP_CIPHER_EN] = 0x134, + [PWRAP_CIPHER_RDY] = 0x138, + [PWRAP_CIPHER_MODE] = 0x13c, + [PWRAP_CIPHER_SWRST] = 0x140, + [PWRAP_DCM_EN] = 0x144, + [PWRAP_DCM_DBC_PRD] = 0x148, +}; + +static int mt8135_regs[] = { + [PWRAP_MUX_SEL] = 0x0, + [PWRAP_WRAP_EN] = 0x4, + [PWRAP_DIO_EN] = 0x8, + [PWRAP_SIDLY] = 0xc, + [PWRAP_CSHEXT] = 0x10, + [PWRAP_CSHEXT_WRITE] = 0x14, + [PWRAP_CSHEXT_READ] = 0x18, + [PWRAP_CSLEXT_START] = 0x1c, + [PWRAP_CSLEXT_END] = 0x20, + [PWRAP_STAUPD_PRD] = 0x24, + [PWRAP_STAUPD_GRPEN] = 0x28, + [PWRAP_STAUPD_MAN_TRIG] = 0x2c, + [PWRAP_STAUPD_STA] = 0x30, + [PWRAP_EVENT_IN_EN] = 0x34, + [PWRAP_EVENT_DST_EN] = 0x38, + [PWRAP_WRAP_STA] = 0x3c, + [PWRAP_RRARB_INIT] = 0x40, + [PWRAP_RRARB_EN] = 0x44, + [PWRAP_RRARB_STA0] = 0x48, + [PWRAP_RRARB_STA1] = 0x4c, + [PWRAP_HARB_INIT] = 0x50, + [PWRAP_HARB_HPRIO] = 0x54, + [PWRAP_HIPRIO_ARB_EN] = 0x58, + [PWRAP_HARB_STA0] = 0x5c, + [PWRAP_HARB_STA1] = 0x60, + [PWRAP_MAN_EN] = 0x64, + [PWRAP_MAN_CMD] = 0x68, + [PWRAP_MAN_RDATA] = 0x6c, + [PWRAP_MAN_VLDCLR] = 0x70, + [PWRAP_WACS0_EN] = 0x74, + [PWRAP_INIT_DONE0] = 0x78, + [PWRAP_WACS0_CMD] = 0x7c, + [PWRAP_WACS0_RDATA] = 0x80, + [PWRAP_WACS0_VLDCLR] = 0x84, + [PWRAP_WACS1_EN] = 0x88, + [PWRAP_INIT_DONE1] = 0x8c, + [PWRAP_WACS1_CMD] = 0x90, + [PWRAP_WACS1_RDATA] = 0x94, + [PWRAP_WACS1_VLDCLR] = 0x98, + [PWRAP_WACS2_EN] = 0x9c, + [PWRAP_INIT_DONE2] = 0xa0, + [PWRAP_WACS2_CMD] = 0xa4, + [PWRAP_WACS2_RDATA] = 0xa8, + [PWRAP_WACS2_VLDCLR] = 0xac, + [PWRAP_INT_EN] = 0xb0, + [PWRAP_INT_FLG_RAW] = 0xb4, + [PWRAP_INT_FLG] = 0xb8, + [PWRAP_INT_CLR] = 0xbc, + [PWRAP_SIG_ADR] = 0xc0, + [PWRAP_SIG_MODE] = 0xc4, + [PWRAP_SIG_VALUE] = 0xc8, + [PWRAP_SIG_ERRVAL] = 0xcc, + [PWRAP_CRC_EN] = 0xd0, + [PWRAP_EVENT_STA] = 0xd4, + [PWRAP_EVENT_STACLR] = 0xd8, + [PWRAP_TIMER_EN] = 0xdc, + [PWRAP_TIMER_STA] = 0xe0, + [PWRAP_WDT_UNIT] = 0xe4, + [PWRAP_WDT_SRC_EN] = 0xe8, + [PWRAP_WDT_FLG] = 0xec, + [PWRAP_DEBUG_INT_SEL] = 0xf0, + [PWRAP_CIPHER_KEY_SEL] = 0x134, + [PWRAP_CIPHER_IV_SEL] = 0x138, + [PWRAP_CIPHER_LOAD] = 0x13c, + [PWRAP_CIPHER_START] = 0x140, + [PWRAP_CIPHER_RDY] = 0x144, + [PWRAP_CIPHER_MODE] = 0x148, + [PWRAP_CIPHER_SWRST] = 0x14c, + [PWRAP_DCM_EN] = 0x15c, + [PWRAP_DCM_DBC_PRD] = 0x160, +}; + +enum pwrap_type { + PWRAP_MT8135, + PWRAP_MT8173, +}; + +struct pmic_wrapper_type { + int *regs; + enum pwrap_type type; + u32 arb_en_all; +}; + +static struct pmic_wrapper_type pwrap_mt8135 = { + .regs = mt8135_regs, + .type = PWRAP_MT8135, + .arb_en_all = 0x1ff, +}; + +static struct pmic_wrapper_type pwrap_mt8173 = { + .regs = mt8173_regs, + .type = PWRAP_MT8173, + .arb_en_all = 0x3f, +}; + +struct pmic_wrapper { + struct device *dev; + void __iomem *base; + struct regmap *regmap; + int *regs; + enum pwrap_type type; + u32 arb_en_all; + struct clk *clk_spi; + struct clk *clk_wrap; + struct reset_control *rstc; + + struct reset_control *rstc_bridge; + void __iomem *bridge_base; +}; + +static inline int pwrap_is_mt8135(struct pmic_wrapper *wrp) +{ + return wrp->type == PWRAP_MT8135; +} + +static inline int pwrap_is_mt8173(struct pmic_wrapper *wrp) +{ + return wrp->type == PWRAP_MT8173; +} + +static u32 pwrap_readl(struct pmic_wrapper *wrp, enum pwrap_regs reg) +{ + return readl(wrp->base + wrp->regs[reg]); +} + +static void pwrap_writel(struct pmic_wrapper *wrp, u32 val, enum pwrap_regs reg) +{ + writel(val, wrp->base + wrp->regs[reg]); +} + +static bool pwrap_is_fsm_idle(struct pmic_wrapper *wrp) +{ + u32 val = pwrap_readl(wrp, PWRAP_WACS2_RDATA); + + return PWRAP_GET_WACS_FSM(val) == PWRAP_WACS_FSM_IDLE; +} + +static bool pwrap_is_fsm_vldclr(struct pmic_wrapper *wrp) +{ + u32 val = pwrap_readl(wrp, PWRAP_WACS2_RDATA); + + return PWRAP_GET_WACS_FSM(val) == PWRAP_WACS_FSM_WFVLDCLR; +} + +static bool pwrap_is_sync_idle(struct pmic_wrapper *wrp) +{ + return pwrap_readl(wrp, PWRAP_WACS2_RDATA) & PWRAP_STATE_SYNC_IDLE0; +} + +static bool pwrap_is_fsm_idle_and_sync_idle(struct pmic_wrapper *wrp) +{ + u32 val = pwrap_readl(wrp, PWRAP_WACS2_RDATA); + + return (PWRAP_GET_WACS_FSM(val) == PWRAP_WACS_FSM_IDLE) && + (val & PWRAP_STATE_SYNC_IDLE0); +} + +static int pwrap_wait_for_state(struct pmic_wrapper *wrp, + bool (*fp)(struct pmic_wrapper *)) +{ + unsigned long timeout; + + timeout = jiffies + usecs_to_jiffies(255); + + do { + if (time_after(jiffies, timeout)) + return fp(wrp) ? 0 : -ETIMEDOUT; + if (fp(wrp)) + return 0; + } while (1); +} + +static int pwrap_write(struct pmic_wrapper *wrp, u32 adr, u32 wdata) +{ + int ret; + u32 val; + + val = pwrap_readl(wrp, PWRAP_WACS2_RDATA); + if (PWRAP_GET_WACS_FSM(val) == PWRAP_WACS_FSM_WFVLDCLR) + pwrap_writel(wrp, 1, PWRAP_WACS2_VLDCLR); + + ret = pwrap_wait_for_state(wrp, pwrap_is_fsm_idle); + if (ret) + return ret; + + pwrap_writel(wrp, (1 << 31) | ((adr >> 1) << 16) | wdata, + PWRAP_WACS2_CMD); + + return 0; +} + +static int pwrap_read(struct pmic_wrapper *wrp, u32 adr, u32 *rdata) +{ + int ret; + u32 val; + + val = pwrap_readl(wrp, PWRAP_WACS2_RDATA); + if (PWRAP_GET_WACS_FSM(val) == PWRAP_WACS_FSM_WFVLDCLR) + pwrap_writel(wrp, 1, PWRAP_WACS2_VLDCLR); + + ret = pwrap_wait_for_state(wrp, pwrap_is_fsm_idle); + if (ret) + return ret; + + pwrap_writel(wrp, (adr >> 1) << 16, PWRAP_WACS2_CMD); + + ret = pwrap_wait_for_state(wrp, pwrap_is_fsm_vldclr); + if (ret) + return ret; + + *rdata = PWRAP_GET_WACS_RDATA(pwrap_readl(wrp, PWRAP_WACS2_RDATA)); + + return 0; +} + +static int pwrap_regmap_read(void *context, u32 adr, u32 *rdata) +{ + return pwrap_read(context, adr, rdata); +} + +static int pwrap_regmap_write(void *context, u32 adr, u32 wdata) +{ + return pwrap_write(context, adr, wdata); +} + +static int pwrap_reset_spislave(struct pmic_wrapper *wrp) +{ + int ret, i; + + pwrap_writel(wrp, 0, PWRAP_HIPRIO_ARB_EN); + pwrap_writel(wrp, 0, PWRAP_WRAP_EN); + pwrap_writel(wrp, 1, PWRAP_MUX_SEL); + pwrap_writel(wrp, 1, PWRAP_MAN_EN); + pwrap_writel(wrp, 0, PWRAP_DIO_EN); + + pwrap_writel(wrp, PWRAP_MAN_CMD_SPI_WRITE | PWRAP_MAN_CMD_OP_CSL, + PWRAP_MAN_CMD); + pwrap_writel(wrp, PWRAP_MAN_CMD_SPI_WRITE | PWRAP_MAN_CMD_OP_OUTS, + PWRAP_MAN_CMD); + pwrap_writel(wrp, PWRAP_MAN_CMD_SPI_WRITE | PWRAP_MAN_CMD_OP_CSH, + PWRAP_MAN_CMD); + + for (i = 0; i < 4; i++) + pwrap_writel(wrp, PWRAP_MAN_CMD_SPI_WRITE | PWRAP_MAN_CMD_OP_OUTS, + PWRAP_MAN_CMD); + + ret = pwrap_wait_for_state(wrp, pwrap_is_sync_idle); + if (ret) { + dev_err(wrp->dev, "%s fail, ret=%d\n", __func__, ret); + return ret; + } + + pwrap_writel(wrp, 0, PWRAP_MAN_EN); + pwrap_writel(wrp, 0, PWRAP_MUX_SEL); + + return 0; +} + +/* + * pwrap_init_sidly - configure serial input delay + * + * This configures the serial input delay. We can configure 0, 2, 4 or 6ns + * delay. Do a read test with all possible values and chose the best delay. + */ +static int pwrap_init_sidly(struct pmic_wrapper *wrp) +{ + u32 rdata; + u32 i; + u32 pass = 0; + signed char dly[16] = { + -1, 0, 1, 0, 2, -1, 1, 1, 3, -1, -1, -1, 3, -1, 2, 1 + }; + + for (i = 0; i < 4; i++) { + pwrap_writel(wrp, i, PWRAP_SIDLY); + pwrap_read(wrp, PWRAP_DEW_READ_TEST, &rdata); + printk("%s: 0x%04x\n", __func__, rdata); + if (rdata == PWRAP_DEW_READ_TEST_VAL) { + dev_dbg(wrp->dev, "[Read Test] pass, SIDLY=%x\n", i); + pass |= 1 << i; + } + } + + if (dly[pass] < 0) { + dev_err(wrp->dev, "sidly pass range 0x%x not continuous\n", + pass); + return -EIO; + } + + pwrap_writel(wrp, dly[pass], PWRAP_SIDLY); + + return 0; +} + +static int pwrap_init_reg_clock(struct pmic_wrapper *wrp) +{ + u32 wdata; + u32 rdata; + unsigned long rate_spi; + int ck_mhz; + + rate_spi = clk_get_rate(wrp->clk_spi); + + if (rate_spi > 26000000) + ck_mhz = 26; + else if (rate_spi > 18) + ck_mhz = 18; + else + ck_mhz = 0; + + pwrap_read(wrp, MT6397_TOP_CKCON2, &rdata); + wdata = rdata & ~(0x3 << 10); + + if (ck_mhz == 18) + wdata |= 0x1 << 10; + + if (pwrap_write(wrp, MT6397_TOP_CKCON2, wdata)) { + dev_err(wrp->dev, "Enable PMIC TOP_CKCON2 fail\n"); + return -EFAULT; + } + + switch (ck_mhz) { + case 18: + if (pwrap_is_mt8135(wrp)) + pwrap_writel(wrp, 0xc, PWRAP_CSHEXT); + pwrap_writel(wrp, 0x4, PWRAP_CSHEXT_WRITE); + pwrap_writel(wrp, 0xc, PWRAP_CSHEXT_READ); + pwrap_writel(wrp, 0x0, PWRAP_CSLEXT_START); + pwrap_writel(wrp, 0x0, PWRAP_CSLEXT_END); + break; + case 26: + if (pwrap_is_mt8135(wrp)) + pwrap_writel(wrp, 0x4, PWRAP_CSHEXT); + pwrap_writel(wrp, 0x0, PWRAP_CSHEXT_WRITE); + pwrap_writel(wrp, 0x4, PWRAP_CSHEXT_READ); + pwrap_writel(wrp, 0x0, PWRAP_CSLEXT_START); + pwrap_writel(wrp, 0x0, PWRAP_CSLEXT_END); + break; + case 0: + if (pwrap_is_mt8135(wrp)) + pwrap_writel(wrp, 0xf, PWRAP_CSHEXT); + pwrap_writel(wrp, 0xf, PWRAP_CSHEXT_WRITE); + pwrap_writel(wrp, 0xf, PWRAP_CSHEXT_READ); + pwrap_writel(wrp, 0xf, PWRAP_CSLEXT_START); + pwrap_writel(wrp, 0xf, PWRAP_CSLEXT_END); + break; + default: + return -EINVAL; + } + + /* Enable PMIC side reg clock */ + if (pwrap_write(wrp, MT6397_WRP_CKPDN, 0) || + pwrap_write(wrp, MT6397_WRP_RST_CON, 0)) { + dev_err(wrp->dev, "Enable PMIC fail\n"); + return -EFAULT; + } + + return 0; +} + +static bool pwrap_is_cipher_ready(struct pmic_wrapper *wrp) +{ + return pwrap_readl(wrp, PWRAP_CIPHER_RDY) & 1; +} + +static bool pwrap_is_pmic_cipher_ready(struct pmic_wrapper *wrp) +{ + u32 rdata; + int ret; + + ret = pwrap_read(wrp, PWRAP_DEW_CIPHER_RDY, &rdata); + if (ret) + return 0; + + return rdata == 1; +} + +static int pwrap_init_cipher(struct pmic_wrapper *wrp) +{ + int ret; + u32 rdata; + + pwrap_writel(wrp, 0x1, PWRAP_CIPHER_SWRST); + pwrap_writel(wrp, 0x0, PWRAP_CIPHER_SWRST); + pwrap_writel(wrp, 0x1, PWRAP_CIPHER_KEY_SEL); + pwrap_writel(wrp, 0x2, PWRAP_CIPHER_IV_SEL); + + if (pwrap_is_mt8135(wrp)) { + pwrap_writel(wrp, 1, PWRAP_CIPHER_LOAD); + pwrap_writel(wrp, 1, PWRAP_CIPHER_START); + } else { + pwrap_writel(wrp, 1, PWRAP_CIPHER_EN); + } + + /* Config cipher mode @PMIC */ + pwrap_write(wrp, PWRAP_DEW_CIPHER_SWRST, 0x1); + pwrap_write(wrp, PWRAP_DEW_CIPHER_SWRST, 0x0); + pwrap_write(wrp, PWRAP_DEW_CIPHER_KEY_SEL, 0x1); + pwrap_write(wrp, PWRAP_DEW_CIPHER_IV_SEL, 0x2); + pwrap_write(wrp, PWRAP_DEW_CIPHER_LOAD, 0x1); + pwrap_write(wrp, PWRAP_DEW_CIPHER_START, 0x1); + + /* wait for cipher data ready at AP */ + ret = pwrap_wait_for_state(wrp, pwrap_is_cipher_ready); + if (ret) { + dev_err(wrp->dev, "cipher data ready at AP fail, ret=%d\n", ret); + return ret; + } + + /* wait for cipher data ready at PMIC */ + ret = pwrap_wait_for_state(wrp, pwrap_is_pmic_cipher_ready); + if (ret) { + dev_err(wrp->dev, "timeout waiting for cipher data ready at PMIC\n"); + return ret; + } + + /* wait for cipher mode idle */ + pwrap_write(wrp, PWRAP_DEW_CIPHER_MODE, 0x1); + ret = pwrap_wait_for_state(wrp, pwrap_is_fsm_idle_and_sync_idle); + if (ret) { + dev_err(wrp->dev, "cipher mode idle fail, ret=%d\n", ret); + return ret; + } + + pwrap_writel(wrp, 1, PWRAP_CIPHER_MODE); + + /* Write Test */ + if (pwrap_write(wrp, PWRAP_DEW_WRITE_TEST, PWRAP_DEW_WRITE_TEST_VAL) || + pwrap_read(wrp, PWRAP_DEW_WRITE_TEST, &rdata) || + (rdata != PWRAP_DEW_WRITE_TEST_VAL)) { + dev_err(wrp->dev, "rdata=0x%04X\n", rdata); + return -EFAULT; + } + + return 0; +} + +static int pwrap_init(struct pmic_wrapper *wrp) +{ + int ret; + u32 rdata; + + reset_control_reset(wrp->rstc); + if (wrp->rstc_bridge) + reset_control_reset(wrp->rstc_bridge); + + if (pwrap_is_mt8173(wrp)) { + /* Enable DCM */ + pwrap_writel(wrp, 3, PWRAP_DCM_EN); + pwrap_writel(wrp, 0, PWRAP_DCM_DBC_PRD); + } + + /* Reset SPI slave */ + ret = pwrap_reset_spislave(wrp); + if (ret) + return ret; + + pwrap_writel(wrp, 1, PWRAP_WRAP_EN); + + pwrap_writel(wrp, wrp->arb_en_all, PWRAP_HIPRIO_ARB_EN); + + pwrap_writel(wrp, 1, PWRAP_WACS2_EN); + + ret = pwrap_init_reg_clock(wrp); + if (ret) + return ret; + + /* Setup serial input delay */ + ret = pwrap_init_sidly(wrp); + if (ret) + return ret; + + if (pwrap_is_mt8173(wrp)) { + /* + * Enable PMIC + * (May not be necessary, depending on S/W partition) + * set dewrap clock bit and clear dewrap reset bit + */ + if (pwrap_write(wrp, MT6397_WRP_CKPDN, 0) || + pwrap_write(wrp, MT6397_WRP_RST_CON, 0)) { + dev_err(wrp->dev, "Enable PMIC fail\n"); + return -EFAULT; + } + } + + /* Enable dual IO mode */ + pwrap_write(wrp, PWRAP_DEW_DIO_EN, 1); + + /* Check IDLE & INIT_DONE in advance */ + ret = pwrap_wait_for_state(wrp, pwrap_is_fsm_idle_and_sync_idle); + if (ret) { + dev_err(wrp->dev, "%s fail, ret=%d\n", __func__, ret); + return ret; + } + + pwrap_writel(wrp, 1, PWRAP_DIO_EN); + + /* Read Test */ + pwrap_read(wrp, PWRAP_DEW_READ_TEST, &rdata); + if (rdata != PWRAP_DEW_READ_TEST_VAL) { + dev_err(wrp->dev, "Read test failed after switch to DIO mode: 0x%04x != 0x%04x\n", + PWRAP_DEW_READ_TEST_VAL, rdata); + return -EFAULT; + } + + /* Enable encryption */ + ret = pwrap_init_cipher(wrp); + if (ret) + return ret; + + /* Signature checking - using CRC */ + if (pwrap_write(wrp, PWRAP_DEW_CRC_EN, 0x1)) + return -EFAULT; + + pwrap_writel(wrp, 0x1, PWRAP_CRC_EN); + pwrap_writel(wrp, 0x0, PWRAP_SIG_MODE); + pwrap_writel(wrp, PWRAP_DEW_CRC_VAL, PWRAP_SIG_ADR); + pwrap_writel(wrp, wrp->arb_en_all, PWRAP_HIPRIO_ARB_EN); + + if (pwrap_is_mt8135(wrp)) + pwrap_writel(wrp, 0x7, PWRAP_RRARB_EN); + + pwrap_writel(wrp, 0x1, PWRAP_WACS0_EN); + pwrap_writel(wrp, 0x1, PWRAP_WACS1_EN); + pwrap_writel(wrp, 0x1, PWRAP_WACS2_EN); + pwrap_writel(wrp, 0x5, PWRAP_STAUPD_PRD); + pwrap_writel(wrp, 0xff, PWRAP_STAUPD_GRPEN); + pwrap_writel(wrp, 0xf, PWRAP_WDT_UNIT); + pwrap_writel(wrp, 0xffffffff, PWRAP_WDT_SRC_EN); + pwrap_writel(wrp, 0x1, PWRAP_TIMER_EN); + pwrap_writel(wrp, ~((1 << 31) | (1 << 1)), PWRAP_INT_EN); + + /* switch event pin from usbdl mode to normal mode @ MT6397 */ + if (pwrap_read(wrp, MT6397_TOP_CKCON3, &rdata) || + pwrap_write(wrp, MT6397_TOP_CKCON3, (rdata & 0x0007))) { + dev_err(wrp->dev, "switch event pin fail\n"); + return -EFAULT; + } + + if (pwrap_is_mt8135(wrp)) { + /* enable pwrap events and pwrap bridge in AP side */ + pwrap_writel(wrp, 0x1, PWRAP_EVENT_IN_EN); + pwrap_writel(wrp, 0xffff, PWRAP_EVENT_DST_EN); + writel(0x7f, wrp->bridge_base + PWRAP_MT8135_BRIDGE_IORD_ARB_EN); + writel(0x1, wrp->bridge_base + PWRAP_MT8135_BRIDGE_WACS3_EN); + writel(0x1, wrp->bridge_base + PWRAP_MT8135_BRIDGE_WACS4_EN); + writel(0x1, wrp->bridge_base + PWRAP_MT8135_BRIDGE_WDT_UNIT); + writel(0xffff, wrp->bridge_base + PWRAP_MT8135_BRIDGE_WDT_SRC_EN); + writel(0x1, wrp->bridge_base + PWRAP_MT8135_BRIDGE_TIMER_EN); + writel(0x7ff, wrp->bridge_base + PWRAP_MT8135_BRIDGE_INT_EN); + + /* enable PMIC event out and sources */ + if (pwrap_write(wrp, PWRAP_DEW_EVENT_OUT_EN, 0x1) || + pwrap_write(wrp, PWRAP_DEW_EVENT_SRC_EN, 0xffff)) { + dev_err(wrp->dev, "enable dewrap fail\n"); + return -EFAULT; + } + } else { + /* PMIC_DEWRAP enables */ + if (pwrap_write(wrp, PWRAP_DEW_EVENT_OUT_EN, 0x1) || + pwrap_write(wrp, PWRAP_DEW_EVENT_SRC_EN, 0xffff)) { + dev_err(wrp->dev, "enable dewrap fail\n"); + return -EFAULT; + } + } + + /* Setup the init done registers */ + pwrap_writel(wrp, 1, PWRAP_INIT_DONE2); + pwrap_writel(wrp, 1, PWRAP_INIT_DONE0); + pwrap_writel(wrp, 1, PWRAP_INIT_DONE1); + + if (pwrap_is_mt8135(wrp)) { + writel(1, wrp->bridge_base + PWRAP_MT8135_BRIDGE_INIT_DONE3); + writel(1, wrp->bridge_base + PWRAP_MT8135_BRIDGE_INIT_DONE4); + } + + return 0; +} + +static irqreturn_t pwrap_interrupt(int irqno, void *dev_id) +{ + u32 rdata; + struct pmic_wrapper *wrp = dev_id; + + rdata = pwrap_readl(wrp, PWRAP_INT_FLG); + + dev_err(wrp->dev, "unexpected interrupt int=0x%x\n", rdata); + + pwrap_writel(wrp, 0xffffffff, PWRAP_INT_CLR); + + return IRQ_HANDLED; +} + +static const struct regmap_config pwrap_regmap_config = { + .reg_bits = 16, + .val_bits = 16, + .reg_stride = 2, + .reg_read = pwrap_regmap_read, + .reg_write = pwrap_regmap_write, + .max_register = 0xffff, +}; + +static struct of_device_id of_pwrap_match_tbl[] = { + { + .compatible = "mediatek,mt8135-pwrap", + .data = &pwrap_mt8135, + }, { + .compatible = "mediatek,mt8173-pwrap", + .data = &pwrap_mt8173, + }, { + /* sentinel */ + } +}; +MODULE_DEVICE_TABLE(of, of_pwrap_match_tbl); + +static int pwrap_probe(struct platform_device *pdev) +{ + int ret, irq; + struct pmic_wrapper *wrp; + struct device_node *np = pdev->dev.of_node; + const struct of_device_id *of_id = + of_match_device(of_pwrap_match_tbl, &pdev->dev); + const struct pmic_wrapper_type *type; + struct resource *res; + + wrp = devm_kzalloc(&pdev->dev, sizeof(*wrp), GFP_KERNEL); + if (!wrp) + return -ENOMEM; + + platform_set_drvdata(pdev, wrp); + + type = of_id->data; + wrp->regs = type->regs; + wrp->type = type->type; + wrp->arb_en_all = type->arb_en_all; + wrp->dev = &pdev->dev; + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pwrap"); + wrp->base = devm_ioremap_resource(wrp->dev, res); + if (IS_ERR(wrp->base)) + return PTR_ERR(wrp->base); + + wrp->rstc = devm_reset_control_get(wrp->dev, "pwrap"); + if (IS_ERR(wrp->rstc)) { + ret = PTR_ERR(wrp->rstc); + dev_dbg(wrp->dev, "cannot get pwrap reset: %d\n", ret); + return ret; + } + + if (pwrap_is_mt8135(wrp)) { + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "pwrap-bridge"); + wrp->bridge_base = devm_ioremap_resource(wrp->dev, res); + if (IS_ERR(wrp->bridge_base)) + return PTR_ERR(wrp->bridge_base); + + wrp->rstc_bridge = devm_reset_control_get(wrp->dev, "pwrap-bridge"); + if (IS_ERR(wrp->rstc_bridge)) { + ret = PTR_ERR(wrp->rstc_bridge); + dev_dbg(wrp->dev, "cannot get pwrap-bridge reset: %d\n", ret); + return ret; + } + } + + wrp->clk_spi = devm_clk_get(wrp->dev, "spi"); + if (IS_ERR(wrp->clk_spi)) { + dev_dbg(wrp->dev, "failed to get clock: %ld\n", PTR_ERR(wrp->clk_spi)); + return PTR_ERR(wrp->clk_spi); + } + + wrp->clk_wrap = devm_clk_get(wrp->dev, "wrap"); + if (IS_ERR(wrp->clk_wrap)) { + dev_dbg(wrp->dev, "failed to get clock: %ld\n", PTR_ERR(wrp->clk_wrap)); + return PTR_ERR(wrp->clk_wrap); + } + + ret = clk_prepare_enable(wrp->clk_spi); + if (ret) + return ret; + + ret = clk_prepare_enable(wrp->clk_wrap); + if (ret) + goto err_out1; + + /* Enable internal dynamic clock */ + pwrap_writel(wrp, 1, PWRAP_DCM_EN); + pwrap_writel(wrp, 0, PWRAP_DCM_DBC_PRD); + + /* + * The PMIC could already be initialized by the bootloader. + * Skip initialization here in this case. + */ + if (!pwrap_readl(wrp, PWRAP_INIT_DONE2)) { + ret = pwrap_init(wrp); + if (ret) { + dev_dbg(wrp->dev, "init failed with %d\n", ret); + goto err_out2; + } + } + + if (!(pwrap_readl(wrp, PWRAP_WACS2_RDATA) & PWRAP_STATE_INIT_DONE0)) { + dev_dbg(wrp->dev, "initialization isn't finished\n"); + return -ENODEV; + } + + irq = platform_get_irq(pdev, 0); + ret = devm_request_irq(wrp->dev, irq, pwrap_interrupt, IRQF_TRIGGER_HIGH, + "mt-pmic-pwrap", wrp); + if (ret) + goto err_out2; + + wrp->regmap = devm_regmap_init(wrp->dev, NULL, wrp, &pwrap_regmap_config); + if (IS_ERR(wrp->regmap)) + return PTR_ERR(wrp->regmap); + + ret = of_platform_populate(np, NULL, NULL, wrp->dev); + if (ret) { + dev_dbg(wrp->dev, "failed to create child devices at %s\n", + np->full_name); + goto err_out2; + } + + return 0; + +err_out2: + clk_disable_unprepare(wrp->clk_wrap); +err_out1: + clk_disable_unprepare(wrp->clk_spi); + + return ret; +} + +static struct platform_driver pwrap_drv = { + .driver = { + .name = "mt-pmic-pwrap", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(of_pwrap_match_tbl), + }, + .probe = pwrap_probe, +}; + +module_platform_driver(pwrap_drv); + +MODULE_AUTHOR("Flora Fu, MediaTek"); +MODULE_DESCRIPTION("MediaTek MT8135 PMIC Wrapper Driver"); +MODULE_LICENSE("GPL"); -- 2.1.4 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 1/2] soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs 2015-02-22 12:02 ` [PATCH 1/2] soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs Sascha Hauer @ 2015-03-09 8:53 ` Matthias Brugger 2015-03-09 10:38 ` Sascha Hauer 0 siblings, 1 reply; 8+ messages in thread From: Matthias Brugger @ 2015-03-09 8:53 UTC (permalink / raw) To: linux-arm-kernel 2015-02-22 13:02 GMT+01:00 Sascha Hauer <s.hauer@pengutronix.de>: > From: Flora Fu <flora.fu@mediatek.com> > > This adds support for the PMIC wrapper found on MediaTek MT8135 and > MT8173 SoCs. > > On MediaTek MT8135, MT8173 and other SoCs the PMIC is connected via > SPI. The SPI master interface is not directly visible to the CPU, but > only through the PMIC wrapper inside the SoC. The communication between > the SoC and the PMIC can optionally be encrypted. Also a non standard > Dual IO SPI mode can be used to increase speed. The MT8135 also supports > a special feature named "IP Pairing". With IP Pairing the pins of some > SoC internal peripherals can be on the PMIC. The signals of these pins > are routed over the SPI bus using the pwrap bridge. Because of these > optional non SPI conform features the PMIC driver is not implemented as > a SPI bus master driver. > > Signed-off-by: Flora Fu, MediaTek > Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> I'm not really happy with the name bounding of the pmic-wrapper to a specific SoC. I wonder if there exist different versions which are shared between different SoCs. It would be nice, if the engineers from Mediatek could shed a light on this. Comments inline. > --- > drivers/soc/Kconfig | 1 + > drivers/soc/Makefile | 1 + > drivers/soc/mediatek/Kconfig | 11 + > drivers/soc/mediatek/Makefile | 1 + > drivers/soc/mediatek/mtk-pmic-wrap.c | 1027 ++++++++++++++++++++++++++++++++++ > 5 files changed, 1041 insertions(+) > create mode 100644 drivers/soc/mediatek/Kconfig > create mode 100644 drivers/soc/mediatek/Makefile > create mode 100644 drivers/soc/mediatek/mtk-pmic-wrap.c > > diff --git a/drivers/soc/Kconfig b/drivers/soc/Kconfig > index 76d6bd4..d8bde82f0 100644 > --- a/drivers/soc/Kconfig > +++ b/drivers/soc/Kconfig > @@ -1,5 +1,6 @@ > menu "SOC (System On Chip) specific Drivers" > > +source "drivers/soc/mediatek/Kconfig" > source "drivers/soc/qcom/Kconfig" > source "drivers/soc/ti/Kconfig" > source "drivers/soc/versatile/Kconfig" > diff --git a/drivers/soc/Makefile b/drivers/soc/Makefile > index 063113d..70042b2 100644 > --- a/drivers/soc/Makefile > +++ b/drivers/soc/Makefile > @@ -2,6 +2,7 @@ > # Makefile for the Linux Kernel SOC specific device drivers. > # > > +obj-$(CONFIG_ARCH_MEDIATEK) += mediatek/ > obj-$(CONFIG_ARCH_QCOM) += qcom/ > obj-$(CONFIG_ARCH_TEGRA) += tegra/ > obj-$(CONFIG_SOC_TI) += ti/ > diff --git a/drivers/soc/mediatek/Kconfig b/drivers/soc/mediatek/Kconfig > new file mode 100644 > index 0000000..b91665a > --- /dev/null > +++ b/drivers/soc/mediatek/Kconfig > @@ -0,0 +1,11 @@ > +# > +# MediaTek SoC drivers > +# > +config MTK_PMIC_WRAP > + tristate "MediaTek PMIC Wrapper Support" > + depends on ARCH_MEDIATEK > + select REGMAP > + help > + Say yes here to add support for MediaTek PMIC Wrapper found > + on the MT8135 and MT8173 SoCs. The PMIC wrapper is a proprietary > + hardware to connect the PMIC. I have found pmic-wrapper on mt6589, mt6582 and mt6592. Most probably more SoCs, if not all will have a pmic-wrapper, so we should take this into account. This message should reflect that. > diff --git a/drivers/soc/mediatek/Makefile b/drivers/soc/mediatek/Makefile > new file mode 100644 > index 0000000..ecaf4de > --- /dev/null > +++ b/drivers/soc/mediatek/Makefile > @@ -0,0 +1 @@ > +obj-$(CONFIG_MTK_PMIC_WRAP) += mtk-pmic-wrap.o > diff --git a/drivers/soc/mediatek/mtk-pmic-wrap.c b/drivers/soc/mediatek/mtk-pmic-wrap.c > new file mode 100644 > index 0000000..bd1f881 > --- /dev/null > +++ b/drivers/soc/mediatek/mtk-pmic-wrap.c > @@ -0,0 +1,1027 @@ > +/* > + * Copyright (c) 2014 MediaTek Inc. > + * Author: Flora Fu, MediaTek > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + */ > +#define DEBUG > +#include <linux/clk.h> > +#include <linux/interrupt.h> > +#include <linux/io.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/of_device.h> > +#include <linux/platform_device.h> > +#include <linux/regmap.h> > +#include <linux/reset.h> > + > +#define PWRAP_MT8135_BRIDGE_IORD_ARB_EN 0x4 > +#define PWRAP_MT8135_BRIDGE_WACS3_EN 0x10 > +#define PWRAP_MT8135_BRIDGE_INIT_DONE3 0x14 > +#define PWRAP_MT8135_BRIDGE_WACS4_EN 0x24 > +#define PWRAP_MT8135_BRIDGE_INIT_DONE4 0x28 > +#define PWRAP_MT8135_BRIDGE_INT_EN 0x38 > +#define PWRAP_MT8135_BRIDGE_TIMER_EN 0x48 > +#define PWRAP_MT8135_BRIDGE_WDT_UNIT 0x50 > +#define PWRAP_MT8135_BRIDGE_WDT_SRC_EN 0x54 > + > +/* macro for wrapper status */ > +#define PWRAP_GET_WACS_RDATA(x) (((x) >> 0) & 0x0000ffff) > +#define PWRAP_GET_WACS_FSM(x) (((x) >> 16) & 0x00000007) > +#define PWRAP_GET_WACS_REQ(x) (((x) >> 19) & 0x00000001) > +#define PWRAP_STATE_SYNC_IDLE0 (1 << 20) > +#define PWRAP_STATE_INIT_DONE0 (1 << 21) > + > +/* macro for WACS FSM */ > +#define PWRAP_WACS_FSM_IDLE 0x00 > +#define PWRAP_WACS_FSM_REQ 0x02 > +#define PWRAP_WACS_FSM_WFDLE 0x04 > +#define PWRAP_WACS_FSM_WFVLDCLR 0x06 > +#define PWRAP_WACS_INIT_DONE 0x01 > +#define PWRAP_WACS_WACS_SYNC_IDLE 0x01 > +#define PWRAP_WACS_SYNC_BUSY 0x00 > + > +/* macro for device wrapper default value */ > +#define PWRAP_DEW_READ_TEST_VAL 0x5aa5 > +#define PWRAP_DEW_WRITE_TEST_VAL 0xa55a > + > +/* macro for manual command */ > +#define PWRAP_MAN_CMD_SPI_WRITE (1 << 13) > +#define PWRAP_MAN_CMD_OP_CSH (0x0 << 8) > +#define PWRAP_MAN_CMD_OP_CSL (0x1 << 8) > +#define PWRAP_MAN_CMD_OP_CK (0x2 << 8) > +#define PWRAP_MAN_CMD_OP_OUTS (0x8 << 8) > +#define PWRAP_MAN_CMD_OP_OUTD (0x9 << 8) > +#define PWRAP_MAN_CMD_OP_OUTQ (0xa << 8) > + > +/* macro for slave device wrapper registers */ > +#define PWRAP_DEW_BASE 0xbc00 > +#define PWRAP_DEW_EVENT_OUT_EN (PWRAP_DEW_BASE + 0x0) > +#define PWRAP_DEW_DIO_EN (PWRAP_DEW_BASE + 0x2) > +#define PWRAP_DEW_EVENT_SRC_EN (PWRAP_DEW_BASE + 0x4) > +#define PWRAP_DEW_EVENT_SRC (PWRAP_DEW_BASE + 0x6) > +#define PWRAP_DEW_EVENT_FLAG (PWRAP_DEW_BASE + 0x8) > +#define PWRAP_DEW_READ_TEST (PWRAP_DEW_BASE + 0xa) > +#define PWRAP_DEW_WRITE_TEST (PWRAP_DEW_BASE + 0xc) > +#define PWRAP_DEW_CRC_EN (PWRAP_DEW_BASE + 0xe) > +#define PWRAP_DEW_CRC_VAL (PWRAP_DEW_BASE + 0x10) > +#define PWRAP_DEW_MON_GRP_SEL (PWRAP_DEW_BASE + 0x12) > +#define PWRAP_DEW_MON_FLAG_SEL (PWRAP_DEW_BASE + 0x14) > +#define PWRAP_DEW_EVENT_TEST (PWRAP_DEW_BASE + 0x16) > +#define PWRAP_DEW_CIPHER_KEY_SEL (PWRAP_DEW_BASE + 0x18) > +#define PWRAP_DEW_CIPHER_IV_SEL (PWRAP_DEW_BASE + 0x1a) > +#define PWRAP_DEW_CIPHER_LOAD (PWRAP_DEW_BASE + 0x1c) > +#define PWRAP_DEW_CIPHER_START (PWRAP_DEW_BASE + 0x1e) > +#define PWRAP_DEW_CIPHER_RDY (PWRAP_DEW_BASE + 0x20) > +#define PWRAP_DEW_CIPHER_MODE (PWRAP_DEW_BASE + 0x22) > +#define PWRAP_DEW_CIPHER_SWRST (PWRAP_DEW_BASE + 0x24) > +#define PWRAP_MT8173_DEW_CIPHER_IV0 (PWRAP_DEW_BASE + 0x26) > +#define PWRAP_MT8173_DEW_CIPHER_IV1 (PWRAP_DEW_BASE + 0x28) > +#define PWRAP_MT8173_DEW_CIPHER_IV2 (PWRAP_DEW_BASE + 0x2a) > +#define PWRAP_MT8173_DEW_CIPHER_IV3 (PWRAP_DEW_BASE + 0x2c) > +#define PWRAP_MT8173_DEW_CIPHER_IV4 (PWRAP_DEW_BASE + 0x2e) > +#define PWRAP_MT8173_DEW_CIPHER_IV5 (PWRAP_DEW_BASE + 0x30) > + > +/* > + * FIXME: These shouldn't be here. These registers are on the PMIC, > + * so they should be touched in the PMIC driver, not the driver > + * granting access to it. > + */ > +#define MT6397_WRP_CKPDN 0x011a > +#define MT6397_WRP_RST_CON 0x0120 > +#define MT6397_TOP_CKCON2 0x012a > +#define MT6397_TOP_CKCON3 0x01d4 We should not mix up between pmic-wrapper and pmic. > + > +enum pwrap_regs { > + PWRAP_MUX_SEL, > + PWRAP_WRAP_EN, > + PWRAP_DIO_EN, > + PWRAP_SIDLY, > + PWRAP_CSHEXT_WRITE, > + PWRAP_CSHEXT_READ, > + PWRAP_CSLEXT_START, > + PWRAP_CSLEXT_END, > + PWRAP_STAUPD_PRD, > + PWRAP_STAUPD_GRPEN, > + PWRAP_STAUPD_MAN_TRIG, > + PWRAP_STAUPD_STA, > + PWRAP_WRAP_STA, > + PWRAP_HARB_INIT, > + PWRAP_HARB_HPRIO, > + PWRAP_HIPRIO_ARB_EN, > + PWRAP_HARB_STA0, > + PWRAP_HARB_STA1, > + PWRAP_MAN_EN, > + PWRAP_MAN_CMD, > + PWRAP_MAN_RDATA, > + PWRAP_MAN_VLDCLR, > + PWRAP_WACS0_EN, > + PWRAP_INIT_DONE0, > + PWRAP_WACS0_CMD, > + PWRAP_WACS0_RDATA, > + PWRAP_WACS0_VLDCLR, > + PWRAP_WACS1_EN, > + PWRAP_INIT_DONE1, > + PWRAP_WACS1_CMD, > + PWRAP_WACS1_RDATA, > + PWRAP_WACS1_VLDCLR, > + PWRAP_WACS2_EN, > + PWRAP_INIT_DONE2, > + PWRAP_WACS2_CMD, > + PWRAP_WACS2_RDATA, > + PWRAP_WACS2_VLDCLR, > + PWRAP_INT_EN, > + PWRAP_INT_FLG_RAW, > + PWRAP_INT_FLG, > + PWRAP_INT_CLR, > + PWRAP_SIG_ADR, > + PWRAP_SIG_MODE, > + PWRAP_SIG_VALUE, > + PWRAP_SIG_ERRVAL, > + PWRAP_CRC_EN, > + PWRAP_TIMER_EN, > + PWRAP_TIMER_STA, > + PWRAP_WDT_UNIT, > + PWRAP_WDT_SRC_EN, > + PWRAP_WDT_FLG, > + PWRAP_DEBUG_INT_SEL, > + PWRAP_CIPHER_KEY_SEL, > + PWRAP_CIPHER_IV_SEL, > + PWRAP_CIPHER_RDY, > + PWRAP_CIPHER_MODE, > + PWRAP_CIPHER_SWRST, > + PWRAP_DCM_EN, > + PWRAP_DCM_DBC_PRD, > + > + /* MT8135 only regs */ > + PWRAP_CSHEXT, > + PWRAP_EVENT_IN_EN, > + PWRAP_EVENT_DST_EN, > + PWRAP_RRARB_INIT, > + PWRAP_RRARB_EN, > + PWRAP_RRARB_STA0, > + PWRAP_RRARB_STA1, > + PWRAP_EVENT_STA, > + PWRAP_EVENT_STACLR, > + PWRAP_CIPHER_LOAD, > + PWRAP_CIPHER_START, This registers exist on mt6589 as well, which makes me think that the wrapper might have the same internal version. > + > + /* MT8173 only regs */ > + PWRAP_RDDMY, > + PWRAP_SI_CK_CON, > + PWRAP_DVFS_ADR0, > + PWRAP_DVFS_WDATA0, > + PWRAP_DVFS_ADR1, > + PWRAP_DVFS_WDATA1, > + PWRAP_DVFS_ADR2, > + PWRAP_DVFS_WDATA2, > + PWRAP_DVFS_ADR3, > + PWRAP_DVFS_WDATA3, > + PWRAP_DVFS_ADR4, > + PWRAP_DVFS_WDATA4, > + PWRAP_DVFS_ADR5, > + PWRAP_DVFS_WDATA5, > + PWRAP_DVFS_ADR6, > + PWRAP_DVFS_WDATA6, > + PWRAP_DVFS_ADR7, > + PWRAP_DVFS_WDATA7, > + PWRAP_SPMINF_STA, > + PWRAP_CIPHER_EN, > +}; > + > +static int mt8173_regs[] = { > + [PWRAP_MUX_SEL] = 0x0, > + [PWRAP_WRAP_EN] = 0x4, > + [PWRAP_DIO_EN] = 0x8, > + [PWRAP_SIDLY] = 0xc, > + [PWRAP_RDDMY] = 0x10, > + [PWRAP_SI_CK_CON] = 0x14, > + [PWRAP_CSHEXT_WRITE] = 0x18, > + [PWRAP_CSHEXT_READ] = 0x1c, > + [PWRAP_CSLEXT_START] = 0x20, > + [PWRAP_CSLEXT_END] = 0x24, > + [PWRAP_STAUPD_PRD] = 0x28, > + [PWRAP_STAUPD_GRPEN] = 0x2c, > + [PWRAP_STAUPD_MAN_TRIG] = 0x40, > + [PWRAP_STAUPD_STA] = 0x44, > + [PWRAP_WRAP_STA] = 0x48, > + [PWRAP_HARB_INIT] = 0x4c, > + [PWRAP_HARB_HPRIO] = 0x50, > + [PWRAP_HIPRIO_ARB_EN] = 0x54, > + [PWRAP_HARB_STA0] = 0x58, > + [PWRAP_HARB_STA1] = 0x5c, > + [PWRAP_MAN_EN] = 0x60, > + [PWRAP_MAN_CMD] = 0x64, > + [PWRAP_MAN_RDATA] = 0x68, > + [PWRAP_MAN_VLDCLR] = 0x6c, > + [PWRAP_WACS0_EN] = 0x70, > + [PWRAP_INIT_DONE0] = 0x74, > + [PWRAP_WACS0_CMD] = 0x78, > + [PWRAP_WACS0_RDATA] = 0x7c, > + [PWRAP_WACS0_VLDCLR] = 0x80, > + [PWRAP_WACS1_EN] = 0x84, > + [PWRAP_INIT_DONE1] = 0x88, > + [PWRAP_WACS1_CMD] = 0x8c, > + [PWRAP_WACS1_RDATA] = 0x90, > + [PWRAP_WACS1_VLDCLR] = 0x94, > + [PWRAP_WACS2_EN] = 0x98, > + [PWRAP_INIT_DONE2] = 0x9c, > + [PWRAP_WACS2_CMD] = 0xa0, > + [PWRAP_WACS2_RDATA] = 0xa4, > + [PWRAP_WACS2_VLDCLR] = 0xa8, > + [PWRAP_INT_EN] = 0xac, > + [PWRAP_INT_FLG_RAW] = 0xb0, > + [PWRAP_INT_FLG] = 0xb4, > + [PWRAP_INT_CLR] = 0xb8, > + [PWRAP_SIG_ADR] = 0xbc, > + [PWRAP_SIG_MODE] = 0xc0, > + [PWRAP_SIG_VALUE] = 0xc4, > + [PWRAP_SIG_ERRVAL] = 0xc8, > + [PWRAP_CRC_EN] = 0xcc, > + [PWRAP_TIMER_EN] = 0xd0, > + [PWRAP_TIMER_STA] = 0xd4, > + [PWRAP_WDT_UNIT] = 0xd8, > + [PWRAP_WDT_SRC_EN] = 0xdc, > + [PWRAP_WDT_FLG] = 0xe0, > + [PWRAP_DEBUG_INT_SEL] = 0xe4, > + [PWRAP_DVFS_ADR0] = 0xe8, > + [PWRAP_DVFS_WDATA0] = 0xec, > + [PWRAP_DVFS_ADR1] = 0xf0, > + [PWRAP_DVFS_WDATA1] = 0xf4, > + [PWRAP_DVFS_ADR2] = 0xf8, > + [PWRAP_DVFS_WDATA2] = 0xfc, > + [PWRAP_DVFS_ADR3] = 0x100, > + [PWRAP_DVFS_WDATA3] = 0x104, > + [PWRAP_DVFS_ADR4] = 0x108, > + [PWRAP_DVFS_WDATA4] = 0x10c, > + [PWRAP_DVFS_ADR5] = 0x110, > + [PWRAP_DVFS_WDATA5] = 0x114, > + [PWRAP_DVFS_ADR6] = 0x118, > + [PWRAP_DVFS_WDATA6] = 0x11c, > + [PWRAP_DVFS_ADR7] = 0x120, > + [PWRAP_DVFS_WDATA7] = 0x124, > + [PWRAP_SPMINF_STA] = 0x128, > + [PWRAP_CIPHER_KEY_SEL] = 0x12c, > + [PWRAP_CIPHER_IV_SEL] = 0x130, > + [PWRAP_CIPHER_EN] = 0x134, > + [PWRAP_CIPHER_RDY] = 0x138, > + [PWRAP_CIPHER_MODE] = 0x13c, > + [PWRAP_CIPHER_SWRST] = 0x140, > + [PWRAP_DCM_EN] = 0x144, > + [PWRAP_DCM_DBC_PRD] = 0x148, > +}; > + > +static int mt8135_regs[] = { > + [PWRAP_MUX_SEL] = 0x0, > + [PWRAP_WRAP_EN] = 0x4, > + [PWRAP_DIO_EN] = 0x8, > + [PWRAP_SIDLY] = 0xc, > + [PWRAP_CSHEXT] = 0x10, > + [PWRAP_CSHEXT_WRITE] = 0x14, > + [PWRAP_CSHEXT_READ] = 0x18, > + [PWRAP_CSLEXT_START] = 0x1c, > + [PWRAP_CSLEXT_END] = 0x20, > + [PWRAP_STAUPD_PRD] = 0x24, > + [PWRAP_STAUPD_GRPEN] = 0x28, > + [PWRAP_STAUPD_MAN_TRIG] = 0x2c, > + [PWRAP_STAUPD_STA] = 0x30, > + [PWRAP_EVENT_IN_EN] = 0x34, > + [PWRAP_EVENT_DST_EN] = 0x38, > + [PWRAP_WRAP_STA] = 0x3c, > + [PWRAP_RRARB_INIT] = 0x40, > + [PWRAP_RRARB_EN] = 0x44, > + [PWRAP_RRARB_STA0] = 0x48, > + [PWRAP_RRARB_STA1] = 0x4c, > + [PWRAP_HARB_INIT] = 0x50, > + [PWRAP_HARB_HPRIO] = 0x54, > + [PWRAP_HIPRIO_ARB_EN] = 0x58, > + [PWRAP_HARB_STA0] = 0x5c, > + [PWRAP_HARB_STA1] = 0x60, > + [PWRAP_MAN_EN] = 0x64, > + [PWRAP_MAN_CMD] = 0x68, > + [PWRAP_MAN_RDATA] = 0x6c, > + [PWRAP_MAN_VLDCLR] = 0x70, > + [PWRAP_WACS0_EN] = 0x74, > + [PWRAP_INIT_DONE0] = 0x78, > + [PWRAP_WACS0_CMD] = 0x7c, > + [PWRAP_WACS0_RDATA] = 0x80, > + [PWRAP_WACS0_VLDCLR] = 0x84, > + [PWRAP_WACS1_EN] = 0x88, > + [PWRAP_INIT_DONE1] = 0x8c, > + [PWRAP_WACS1_CMD] = 0x90, > + [PWRAP_WACS1_RDATA] = 0x94, > + [PWRAP_WACS1_VLDCLR] = 0x98, > + [PWRAP_WACS2_EN] = 0x9c, > + [PWRAP_INIT_DONE2] = 0xa0, > + [PWRAP_WACS2_CMD] = 0xa4, > + [PWRAP_WACS2_RDATA] = 0xa8, > + [PWRAP_WACS2_VLDCLR] = 0xac, > + [PWRAP_INT_EN] = 0xb0, > + [PWRAP_INT_FLG_RAW] = 0xb4, > + [PWRAP_INT_FLG] = 0xb8, > + [PWRAP_INT_CLR] = 0xbc, > + [PWRAP_SIG_ADR] = 0xc0, > + [PWRAP_SIG_MODE] = 0xc4, > + [PWRAP_SIG_VALUE] = 0xc8, > + [PWRAP_SIG_ERRVAL] = 0xcc, > + [PWRAP_CRC_EN] = 0xd0, > + [PWRAP_EVENT_STA] = 0xd4, > + [PWRAP_EVENT_STACLR] = 0xd8, > + [PWRAP_TIMER_EN] = 0xdc, > + [PWRAP_TIMER_STA] = 0xe0, > + [PWRAP_WDT_UNIT] = 0xe4, > + [PWRAP_WDT_SRC_EN] = 0xe8, > + [PWRAP_WDT_FLG] = 0xec, > + [PWRAP_DEBUG_INT_SEL] = 0xf0, > + [PWRAP_CIPHER_KEY_SEL] = 0x134, > + [PWRAP_CIPHER_IV_SEL] = 0x138, > + [PWRAP_CIPHER_LOAD] = 0x13c, > + [PWRAP_CIPHER_START] = 0x140, > + [PWRAP_CIPHER_RDY] = 0x144, > + [PWRAP_CIPHER_MODE] = 0x148, > + [PWRAP_CIPHER_SWRST] = 0x14c, > + [PWRAP_DCM_EN] = 0x15c, > + [PWRAP_DCM_DBC_PRD] = 0x160, > +}; I'm not really happy with putting this arrays in here. When adding more SoCs this will bloat up the file. Better if we put this definitions in a header file. > + > +enum pwrap_type { > + PWRAP_MT8135, > + PWRAP_MT8173, > +}; > + > +struct pmic_wrapper_type { > + int *regs; > + enum pwrap_type type; > + u32 arb_en_all; > +}; > + > +static struct pmic_wrapper_type pwrap_mt8135 = { > + .regs = mt8135_regs, > + .type = PWRAP_MT8135, > + .arb_en_all = 0x1ff, > +}; > + > +static struct pmic_wrapper_type pwrap_mt8173 = { > + .regs = mt8173_regs, > + .type = PWRAP_MT8173, > + .arb_en_all = 0x3f, > +}; > + > +struct pmic_wrapper { > + struct device *dev; > + void __iomem *base; > + struct regmap *regmap; > + int *regs; > + enum pwrap_type type; > + u32 arb_en_all; > + struct clk *clk_spi; > + struct clk *clk_wrap; > + struct reset_control *rstc; > + > + struct reset_control *rstc_bridge; > + void __iomem *bridge_base; > +}; > + > +static inline int pwrap_is_mt8135(struct pmic_wrapper *wrp) > +{ > + return wrp->type == PWRAP_MT8135; > +} > + > +static inline int pwrap_is_mt8173(struct pmic_wrapper *wrp) > +{ > + return wrp->type == PWRAP_MT8173; > +} > + > +static u32 pwrap_readl(struct pmic_wrapper *wrp, enum pwrap_regs reg) > +{ > + return readl(wrp->base + wrp->regs[reg]); > +} > + > +static void pwrap_writel(struct pmic_wrapper *wrp, u32 val, enum pwrap_regs reg) > +{ > + writel(val, wrp->base + wrp->regs[reg]); > +} > + > +static bool pwrap_is_fsm_idle(struct pmic_wrapper *wrp) > +{ > + u32 val = pwrap_readl(wrp, PWRAP_WACS2_RDATA); > + > + return PWRAP_GET_WACS_FSM(val) == PWRAP_WACS_FSM_IDLE; > +} > + > +static bool pwrap_is_fsm_vldclr(struct pmic_wrapper *wrp) > +{ > + u32 val = pwrap_readl(wrp, PWRAP_WACS2_RDATA); > + > + return PWRAP_GET_WACS_FSM(val) == PWRAP_WACS_FSM_WFVLDCLR; > +} > + > +static bool pwrap_is_sync_idle(struct pmic_wrapper *wrp) > +{ > + return pwrap_readl(wrp, PWRAP_WACS2_RDATA) & PWRAP_STATE_SYNC_IDLE0; > +} > + > +static bool pwrap_is_fsm_idle_and_sync_idle(struct pmic_wrapper *wrp) > +{ > + u32 val = pwrap_readl(wrp, PWRAP_WACS2_RDATA); > + > + return (PWRAP_GET_WACS_FSM(val) == PWRAP_WACS_FSM_IDLE) && > + (val & PWRAP_STATE_SYNC_IDLE0); > +} > + > +static int pwrap_wait_for_state(struct pmic_wrapper *wrp, > + bool (*fp)(struct pmic_wrapper *)) > +{ > + unsigned long timeout; > + > + timeout = jiffies + usecs_to_jiffies(255); > + > + do { > + if (time_after(jiffies, timeout)) > + return fp(wrp) ? 0 : -ETIMEDOUT; > + if (fp(wrp)) > + return 0; > + } while (1); > +} > + > +static int pwrap_write(struct pmic_wrapper *wrp, u32 adr, u32 wdata) > +{ > + int ret; > + u32 val; > + > + val = pwrap_readl(wrp, PWRAP_WACS2_RDATA); > + if (PWRAP_GET_WACS_FSM(val) == PWRAP_WACS_FSM_WFVLDCLR) > + pwrap_writel(wrp, 1, PWRAP_WACS2_VLDCLR); > + > + ret = pwrap_wait_for_state(wrp, pwrap_is_fsm_idle); > + if (ret) > + return ret; > + > + pwrap_writel(wrp, (1 << 31) | ((adr >> 1) << 16) | wdata, > + PWRAP_WACS2_CMD); > + > + return 0; > +} > + > +static int pwrap_read(struct pmic_wrapper *wrp, u32 adr, u32 *rdata) > +{ > + int ret; > + u32 val; > + > + val = pwrap_readl(wrp, PWRAP_WACS2_RDATA); > + if (PWRAP_GET_WACS_FSM(val) == PWRAP_WACS_FSM_WFVLDCLR) > + pwrap_writel(wrp, 1, PWRAP_WACS2_VLDCLR); > + > + ret = pwrap_wait_for_state(wrp, pwrap_is_fsm_idle); > + if (ret) > + return ret; > + > + pwrap_writel(wrp, (adr >> 1) << 16, PWRAP_WACS2_CMD); > + > + ret = pwrap_wait_for_state(wrp, pwrap_is_fsm_vldclr); > + if (ret) > + return ret; > + > + *rdata = PWRAP_GET_WACS_RDATA(pwrap_readl(wrp, PWRAP_WACS2_RDATA)); > + > + return 0; > +} > + > +static int pwrap_regmap_read(void *context, u32 adr, u32 *rdata) > +{ > + return pwrap_read(context, adr, rdata); > +} > + > +static int pwrap_regmap_write(void *context, u32 adr, u32 wdata) > +{ > + return pwrap_write(context, adr, wdata); > +} > + > +static int pwrap_reset_spislave(struct pmic_wrapper *wrp) > +{ > + int ret, i; > + > + pwrap_writel(wrp, 0, PWRAP_HIPRIO_ARB_EN); > + pwrap_writel(wrp, 0, PWRAP_WRAP_EN); > + pwrap_writel(wrp, 1, PWRAP_MUX_SEL); > + pwrap_writel(wrp, 1, PWRAP_MAN_EN); > + pwrap_writel(wrp, 0, PWRAP_DIO_EN); > + > + pwrap_writel(wrp, PWRAP_MAN_CMD_SPI_WRITE | PWRAP_MAN_CMD_OP_CSL, > + PWRAP_MAN_CMD); > + pwrap_writel(wrp, PWRAP_MAN_CMD_SPI_WRITE | PWRAP_MAN_CMD_OP_OUTS, > + PWRAP_MAN_CMD); > + pwrap_writel(wrp, PWRAP_MAN_CMD_SPI_WRITE | PWRAP_MAN_CMD_OP_CSH, > + PWRAP_MAN_CMD); > + > + for (i = 0; i < 4; i++) > + pwrap_writel(wrp, PWRAP_MAN_CMD_SPI_WRITE | PWRAP_MAN_CMD_OP_OUTS, > + PWRAP_MAN_CMD); > + > + ret = pwrap_wait_for_state(wrp, pwrap_is_sync_idle); > + if (ret) { > + dev_err(wrp->dev, "%s fail, ret=%d\n", __func__, ret); > + return ret; > + } > + > + pwrap_writel(wrp, 0, PWRAP_MAN_EN); > + pwrap_writel(wrp, 0, PWRAP_MUX_SEL); > + > + return 0; > +} > + > +/* > + * pwrap_init_sidly - configure serial input delay > + * > + * This configures the serial input delay. We can configure 0, 2, 4 or 6ns > + * delay. Do a read test with all possible values and chose the best delay. > + */ > +static int pwrap_init_sidly(struct pmic_wrapper *wrp) > +{ > + u32 rdata; > + u32 i; > + u32 pass = 0; > + signed char dly[16] = { > + -1, 0, 1, 0, 2, -1, 1, 1, 3, -1, -1, -1, 3, -1, 2, 1 > + }; > + > + for (i = 0; i < 4; i++) { > + pwrap_writel(wrp, i, PWRAP_SIDLY); > + pwrap_read(wrp, PWRAP_DEW_READ_TEST, &rdata); > + printk("%s: 0x%04x\n", __func__, rdata); > + if (rdata == PWRAP_DEW_READ_TEST_VAL) { > + dev_dbg(wrp->dev, "[Read Test] pass, SIDLY=%x\n", i); > + pass |= 1 << i; > + } > + } > + > + if (dly[pass] < 0) { > + dev_err(wrp->dev, "sidly pass range 0x%x not continuous\n", > + pass); > + return -EIO; > + } > + > + pwrap_writel(wrp, dly[pass], PWRAP_SIDLY); > + > + return 0; > +} > + > +static int pwrap_init_reg_clock(struct pmic_wrapper *wrp) > +{ > + u32 wdata; > + u32 rdata; > + unsigned long rate_spi; > + int ck_mhz; > + > + rate_spi = clk_get_rate(wrp->clk_spi); > + > + if (rate_spi > 26000000) > + ck_mhz = 26; > + else if (rate_spi > 18) Hu, 18 Hz? Looks like a typo. > + ck_mhz = 18; > + else > + ck_mhz = 0; > + > + pwrap_read(wrp, MT6397_TOP_CKCON2, &rdata); > + wdata = rdata & ~(0x3 << 10); > + > + if (ck_mhz == 18) > + wdata |= 0x1 << 10; > + > + if (pwrap_write(wrp, MT6397_TOP_CKCON2, wdata)) { > + dev_err(wrp->dev, "Enable PMIC TOP_CKCON2 fail\n"); > + return -EFAULT; > + } > + > + switch (ck_mhz) { > + case 18: > + if (pwrap_is_mt8135(wrp)) > + pwrap_writel(wrp, 0xc, PWRAP_CSHEXT); If the pmic-wrapper is unique to every SoC, we should think of providing a different way to distinguish between the implementations. Otherwise we will bloat up the code with SoC specific conditionals. > + pwrap_writel(wrp, 0x4, PWRAP_CSHEXT_WRITE); > + pwrap_writel(wrp, 0xc, PWRAP_CSHEXT_READ); > + pwrap_writel(wrp, 0x0, PWRAP_CSLEXT_START); > + pwrap_writel(wrp, 0x0, PWRAP_CSLEXT_END); > + break; > + case 26: > + if (pwrap_is_mt8135(wrp)) > + pwrap_writel(wrp, 0x4, PWRAP_CSHEXT); > + pwrap_writel(wrp, 0x0, PWRAP_CSHEXT_WRITE); > + pwrap_writel(wrp, 0x4, PWRAP_CSHEXT_READ); > + pwrap_writel(wrp, 0x0, PWRAP_CSLEXT_START); > + pwrap_writel(wrp, 0x0, PWRAP_CSLEXT_END); > + break; > + case 0: > + if (pwrap_is_mt8135(wrp)) > + pwrap_writel(wrp, 0xf, PWRAP_CSHEXT); > + pwrap_writel(wrp, 0xf, PWRAP_CSHEXT_WRITE); > + pwrap_writel(wrp, 0xf, PWRAP_CSHEXT_READ); > + pwrap_writel(wrp, 0xf, PWRAP_CSLEXT_START); > + pwrap_writel(wrp, 0xf, PWRAP_CSLEXT_END); > + break; > + default: > + return -EINVAL; > + } > + > + /* Enable PMIC side reg clock */ > + if (pwrap_write(wrp, MT6397_WRP_CKPDN, 0) || > + pwrap_write(wrp, MT6397_WRP_RST_CON, 0)) { Please don't hard code pmic specific commands in the pmic-wrapper code. > + dev_err(wrp->dev, "Enable PMIC fail\n"); > + return -EFAULT; > + } > + > + return 0; > +} > + > +static bool pwrap_is_cipher_ready(struct pmic_wrapper *wrp) > +{ > + return pwrap_readl(wrp, PWRAP_CIPHER_RDY) & 1; > +} > + > +static bool pwrap_is_pmic_cipher_ready(struct pmic_wrapper *wrp) > +{ > + u32 rdata; > + int ret; > + > + ret = pwrap_read(wrp, PWRAP_DEW_CIPHER_RDY, &rdata); > + if (ret) > + return 0; > + > + return rdata == 1; > +} > + > +static int pwrap_init_cipher(struct pmic_wrapper *wrp) > +{ > + int ret; > + u32 rdata; > + > + pwrap_writel(wrp, 0x1, PWRAP_CIPHER_SWRST); > + pwrap_writel(wrp, 0x0, PWRAP_CIPHER_SWRST); > + pwrap_writel(wrp, 0x1, PWRAP_CIPHER_KEY_SEL); > + pwrap_writel(wrp, 0x2, PWRAP_CIPHER_IV_SEL); > + > + if (pwrap_is_mt8135(wrp)) { > + pwrap_writel(wrp, 1, PWRAP_CIPHER_LOAD); > + pwrap_writel(wrp, 1, PWRAP_CIPHER_START); > + } else { > + pwrap_writel(wrp, 1, PWRAP_CIPHER_EN); > + } > + > + /* Config cipher mode @PMIC */ > + pwrap_write(wrp, PWRAP_DEW_CIPHER_SWRST, 0x1); > + pwrap_write(wrp, PWRAP_DEW_CIPHER_SWRST, 0x0); > + pwrap_write(wrp, PWRAP_DEW_CIPHER_KEY_SEL, 0x1); > + pwrap_write(wrp, PWRAP_DEW_CIPHER_IV_SEL, 0x2); > + pwrap_write(wrp, PWRAP_DEW_CIPHER_LOAD, 0x1); > + pwrap_write(wrp, PWRAP_DEW_CIPHER_START, 0x1); > + > + /* wait for cipher data ready at AP */ > + ret = pwrap_wait_for_state(wrp, pwrap_is_cipher_ready); > + if (ret) { > + dev_err(wrp->dev, "cipher data ready at AP fail, ret=%d\n", ret); > + return ret; > + } > + > + /* wait for cipher data ready at PMIC */ > + ret = pwrap_wait_for_state(wrp, pwrap_is_pmic_cipher_ready); > + if (ret) { > + dev_err(wrp->dev, "timeout waiting for cipher data ready at PMIC\n"); > + return ret; > + } > + > + /* wait for cipher mode idle */ > + pwrap_write(wrp, PWRAP_DEW_CIPHER_MODE, 0x1); > + ret = pwrap_wait_for_state(wrp, pwrap_is_fsm_idle_and_sync_idle); > + if (ret) { > + dev_err(wrp->dev, "cipher mode idle fail, ret=%d\n", ret); > + return ret; > + } > + > + pwrap_writel(wrp, 1, PWRAP_CIPHER_MODE); > + > + /* Write Test */ > + if (pwrap_write(wrp, PWRAP_DEW_WRITE_TEST, PWRAP_DEW_WRITE_TEST_VAL) || > + pwrap_read(wrp, PWRAP_DEW_WRITE_TEST, &rdata) || > + (rdata != PWRAP_DEW_WRITE_TEST_VAL)) { > + dev_err(wrp->dev, "rdata=0x%04X\n", rdata); > + return -EFAULT; > + } > + > + return 0; > +} > + > +static int pwrap_init(struct pmic_wrapper *wrp) > +{ > + int ret; > + u32 rdata; > + > + reset_control_reset(wrp->rstc); > + if (wrp->rstc_bridge) > + reset_control_reset(wrp->rstc_bridge); > + > + if (pwrap_is_mt8173(wrp)) { > + /* Enable DCM */ > + pwrap_writel(wrp, 3, PWRAP_DCM_EN); > + pwrap_writel(wrp, 0, PWRAP_DCM_DBC_PRD); > + } > + > + /* Reset SPI slave */ > + ret = pwrap_reset_spislave(wrp); > + if (ret) > + return ret; > + > + pwrap_writel(wrp, 1, PWRAP_WRAP_EN); > + > + pwrap_writel(wrp, wrp->arb_en_all, PWRAP_HIPRIO_ARB_EN); > + > + pwrap_writel(wrp, 1, PWRAP_WACS2_EN); > + > + ret = pwrap_init_reg_clock(wrp); > + if (ret) > + return ret; > + > + /* Setup serial input delay */ > + ret = pwrap_init_sidly(wrp); > + if (ret) > + return ret; > + > + if (pwrap_is_mt8173(wrp)) { > + /* > + * Enable PMIC > + * (May not be necessary, depending on S/W partition) > + * set dewrap clock bit and clear dewrap reset bit > + */ > + if (pwrap_write(wrp, MT6397_WRP_CKPDN, 0) || > + pwrap_write(wrp, MT6397_WRP_RST_CON, 0)) { > + dev_err(wrp->dev, "Enable PMIC fail\n"); > + return -EFAULT; > + } > + } > + > + /* Enable dual IO mode */ > + pwrap_write(wrp, PWRAP_DEW_DIO_EN, 1); > + > + /* Check IDLE & INIT_DONE in advance */ > + ret = pwrap_wait_for_state(wrp, pwrap_is_fsm_idle_and_sync_idle); > + if (ret) { > + dev_err(wrp->dev, "%s fail, ret=%d\n", __func__, ret); > + return ret; > + } > + > + pwrap_writel(wrp, 1, PWRAP_DIO_EN); > + > + /* Read Test */ > + pwrap_read(wrp, PWRAP_DEW_READ_TEST, &rdata); > + if (rdata != PWRAP_DEW_READ_TEST_VAL) { > + dev_err(wrp->dev, "Read test failed after switch to DIO mode: 0x%04x != 0x%04x\n", > + PWRAP_DEW_READ_TEST_VAL, rdata); > + return -EFAULT; > + } > + > + /* Enable encryption */ > + ret = pwrap_init_cipher(wrp); > + if (ret) > + return ret; > + > + /* Signature checking - using CRC */ > + if (pwrap_write(wrp, PWRAP_DEW_CRC_EN, 0x1)) > + return -EFAULT; > + > + pwrap_writel(wrp, 0x1, PWRAP_CRC_EN); > + pwrap_writel(wrp, 0x0, PWRAP_SIG_MODE); > + pwrap_writel(wrp, PWRAP_DEW_CRC_VAL, PWRAP_SIG_ADR); > + pwrap_writel(wrp, wrp->arb_en_all, PWRAP_HIPRIO_ARB_EN); > + > + if (pwrap_is_mt8135(wrp)) > + pwrap_writel(wrp, 0x7, PWRAP_RRARB_EN); > + > + pwrap_writel(wrp, 0x1, PWRAP_WACS0_EN); > + pwrap_writel(wrp, 0x1, PWRAP_WACS1_EN); > + pwrap_writel(wrp, 0x1, PWRAP_WACS2_EN); > + pwrap_writel(wrp, 0x5, PWRAP_STAUPD_PRD); > + pwrap_writel(wrp, 0xff, PWRAP_STAUPD_GRPEN); > + pwrap_writel(wrp, 0xf, PWRAP_WDT_UNIT); > + pwrap_writel(wrp, 0xffffffff, PWRAP_WDT_SRC_EN); > + pwrap_writel(wrp, 0x1, PWRAP_TIMER_EN); > + pwrap_writel(wrp, ~((1 << 31) | (1 << 1)), PWRAP_INT_EN); > + > + /* switch event pin from usbdl mode to normal mode @ MT6397 */ > + if (pwrap_read(wrp, MT6397_TOP_CKCON3, &rdata) || > + pwrap_write(wrp, MT6397_TOP_CKCON3, (rdata & 0x0007))) { > + dev_err(wrp->dev, "switch event pin fail\n"); > + return -EFAULT; > + } > + > + if (pwrap_is_mt8135(wrp)) { > + /* enable pwrap events and pwrap bridge in AP side */ > + pwrap_writel(wrp, 0x1, PWRAP_EVENT_IN_EN); > + pwrap_writel(wrp, 0xffff, PWRAP_EVENT_DST_EN); > + writel(0x7f, wrp->bridge_base + PWRAP_MT8135_BRIDGE_IORD_ARB_EN); > + writel(0x1, wrp->bridge_base + PWRAP_MT8135_BRIDGE_WACS3_EN); > + writel(0x1, wrp->bridge_base + PWRAP_MT8135_BRIDGE_WACS4_EN); > + writel(0x1, wrp->bridge_base + PWRAP_MT8135_BRIDGE_WDT_UNIT); > + writel(0xffff, wrp->bridge_base + PWRAP_MT8135_BRIDGE_WDT_SRC_EN); > + writel(0x1, wrp->bridge_base + PWRAP_MT8135_BRIDGE_TIMER_EN); > + writel(0x7ff, wrp->bridge_base + PWRAP_MT8135_BRIDGE_INT_EN); > + > + /* enable PMIC event out and sources */ > + if (pwrap_write(wrp, PWRAP_DEW_EVENT_OUT_EN, 0x1) || > + pwrap_write(wrp, PWRAP_DEW_EVENT_SRC_EN, 0xffff)) { > + dev_err(wrp->dev, "enable dewrap fail\n"); > + return -EFAULT; > + } > + } else { > + /* PMIC_DEWRAP enables */ > + if (pwrap_write(wrp, PWRAP_DEW_EVENT_OUT_EN, 0x1) || > + pwrap_write(wrp, PWRAP_DEW_EVENT_SRC_EN, 0xffff)) { > + dev_err(wrp->dev, "enable dewrap fail\n"); > + return -EFAULT; > + } > + } > + > + /* Setup the init done registers */ > + pwrap_writel(wrp, 1, PWRAP_INIT_DONE2); > + pwrap_writel(wrp, 1, PWRAP_INIT_DONE0); > + pwrap_writel(wrp, 1, PWRAP_INIT_DONE1); > + > + if (pwrap_is_mt8135(wrp)) { > + writel(1, wrp->bridge_base + PWRAP_MT8135_BRIDGE_INIT_DONE3); > + writel(1, wrp->bridge_base + PWRAP_MT8135_BRIDGE_INIT_DONE4); > + } > + > + return 0; > +} > + > +static irqreturn_t pwrap_interrupt(int irqno, void *dev_id) > +{ > + u32 rdata; > + struct pmic_wrapper *wrp = dev_id; > + > + rdata = pwrap_readl(wrp, PWRAP_INT_FLG); > + > + dev_err(wrp->dev, "unexpected interrupt int=0x%x\n", rdata); > + > + pwrap_writel(wrp, 0xffffffff, PWRAP_INT_CLR); > + > + return IRQ_HANDLED; > +} > + > +static const struct regmap_config pwrap_regmap_config = { > + .reg_bits = 16, > + .val_bits = 16, > + .reg_stride = 2, > + .reg_read = pwrap_regmap_read, > + .reg_write = pwrap_regmap_write, > + .max_register = 0xffff, > +}; > + > +static struct of_device_id of_pwrap_match_tbl[] = { > + { > + .compatible = "mediatek,mt8135-pwrap", > + .data = &pwrap_mt8135, > + }, { > + .compatible = "mediatek,mt8173-pwrap", > + .data = &pwrap_mt8173, > + }, { > + /* sentinel */ > + } > +}; > +MODULE_DEVICE_TABLE(of, of_pwrap_match_tbl); > + > +static int pwrap_probe(struct platform_device *pdev) > +{ > + int ret, irq; > + struct pmic_wrapper *wrp; > + struct device_node *np = pdev->dev.of_node; > + const struct of_device_id *of_id = > + of_match_device(of_pwrap_match_tbl, &pdev->dev); > + const struct pmic_wrapper_type *type; > + struct resource *res; > + > + wrp = devm_kzalloc(&pdev->dev, sizeof(*wrp), GFP_KERNEL); > + if (!wrp) > + return -ENOMEM; > + > + platform_set_drvdata(pdev, wrp); > + > + type = of_id->data; > + wrp->regs = type->regs; > + wrp->type = type->type; > + wrp->arb_en_all = type->arb_en_all; > + wrp->dev = &pdev->dev; > + > + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pwrap"); > + wrp->base = devm_ioremap_resource(wrp->dev, res); > + if (IS_ERR(wrp->base)) > + return PTR_ERR(wrp->base); > + > + wrp->rstc = devm_reset_control_get(wrp->dev, "pwrap"); > + if (IS_ERR(wrp->rstc)) { > + ret = PTR_ERR(wrp->rstc); > + dev_dbg(wrp->dev, "cannot get pwrap reset: %d\n", ret); > + return ret; > + } > + > + if (pwrap_is_mt8135(wrp)) { > + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, > + "pwrap-bridge"); > + wrp->bridge_base = devm_ioremap_resource(wrp->dev, res); > + if (IS_ERR(wrp->bridge_base)) > + return PTR_ERR(wrp->bridge_base); > + > + wrp->rstc_bridge = devm_reset_control_get(wrp->dev, "pwrap-bridge"); > + if (IS_ERR(wrp->rstc_bridge)) { > + ret = PTR_ERR(wrp->rstc_bridge); > + dev_dbg(wrp->dev, "cannot get pwrap-bridge reset: %d\n", ret); > + return ret; > + } > + } > + > + wrp->clk_spi = devm_clk_get(wrp->dev, "spi"); > + if (IS_ERR(wrp->clk_spi)) { > + dev_dbg(wrp->dev, "failed to get clock: %ld\n", PTR_ERR(wrp->clk_spi)); > + return PTR_ERR(wrp->clk_spi); > + } > + > + wrp->clk_wrap = devm_clk_get(wrp->dev, "wrap"); > + if (IS_ERR(wrp->clk_wrap)) { > + dev_dbg(wrp->dev, "failed to get clock: %ld\n", PTR_ERR(wrp->clk_wrap)); > + return PTR_ERR(wrp->clk_wrap); > + } > + > + ret = clk_prepare_enable(wrp->clk_spi); > + if (ret) > + return ret; > + > + ret = clk_prepare_enable(wrp->clk_wrap); > + if (ret) > + goto err_out1; > + > + /* Enable internal dynamic clock */ > + pwrap_writel(wrp, 1, PWRAP_DCM_EN); > + pwrap_writel(wrp, 0, PWRAP_DCM_DBC_PRD); > + > + /* > + * The PMIC could already be initialized by the bootloader. > + * Skip initialization here in this case. > + */ > + if (!pwrap_readl(wrp, PWRAP_INIT_DONE2)) { > + ret = pwrap_init(wrp); > + if (ret) { > + dev_dbg(wrp->dev, "init failed with %d\n", ret); > + goto err_out2; > + } > + } > + > + if (!(pwrap_readl(wrp, PWRAP_WACS2_RDATA) & PWRAP_STATE_INIT_DONE0)) { > + dev_dbg(wrp->dev, "initialization isn't finished\n"); > + return -ENODEV; > + } > + > + irq = platform_get_irq(pdev, 0); > + ret = devm_request_irq(wrp->dev, irq, pwrap_interrupt, IRQF_TRIGGER_HIGH, > + "mt-pmic-pwrap", wrp); > + if (ret) > + goto err_out2; > + > + wrp->regmap = devm_regmap_init(wrp->dev, NULL, wrp, &pwrap_regmap_config); > + if (IS_ERR(wrp->regmap)) > + return PTR_ERR(wrp->regmap); > + > + ret = of_platform_populate(np, NULL, NULL, wrp->dev); > + if (ret) { > + dev_dbg(wrp->dev, "failed to create child devices at %s\n", > + np->full_name); > + goto err_out2; > + } > + > + return 0; > + > +err_out2: > + clk_disable_unprepare(wrp->clk_wrap); > +err_out1: > + clk_disable_unprepare(wrp->clk_spi); > + > + return ret; > +} > + > +static struct platform_driver pwrap_drv = { > + .driver = { > + .name = "mt-pmic-pwrap", > + .owner = THIS_MODULE, > + .of_match_table = of_match_ptr(of_pwrap_match_tbl), > + }, > + .probe = pwrap_probe, > +}; > + > +module_platform_driver(pwrap_drv); > + > +MODULE_AUTHOR("Flora Fu, MediaTek"); > +MODULE_DESCRIPTION("MediaTek MT8135 PMIC Wrapper Driver"); > +MODULE_LICENSE("GPL"); > -- > 2.1.4 > -- motzblog.wordpress.com ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH 1/2] soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs 2015-03-09 8:53 ` Matthias Brugger @ 2015-03-09 10:38 ` Sascha Hauer 2015-03-10 11:21 ` fan.chen 0 siblings, 1 reply; 8+ messages in thread From: Sascha Hauer @ 2015-03-09 10:38 UTC (permalink / raw) To: linux-arm-kernel On Mon, Mar 09, 2015 at 09:53:31AM +0100, Matthias Brugger wrote: > 2015-02-22 13:02 GMT+01:00 Sascha Hauer <s.hauer@pengutronix.de>: > > From: Flora Fu <flora.fu@mediatek.com> > > > > new file mode 100644 > > index 0000000..b91665a > > --- /dev/null > > +++ b/drivers/soc/mediatek/Kconfig > > @@ -0,0 +1,11 @@ > > +# > > +# MediaTek SoC drivers > > +# > > +config MTK_PMIC_WRAP > > + tristate "MediaTek PMIC Wrapper Support" > > + depends on ARCH_MEDIATEK > > + select REGMAP > > + help > > + Say yes here to add support for MediaTek PMIC Wrapper found > > + on the MT8135 and MT8173 SoCs. The PMIC wrapper is a proprietary > > + hardware to connect the PMIC. > > I have found pmic-wrapper on mt6589, mt6582 and mt6592. Most probably > more SoCs, if not all will have a pmic-wrapper, so we should take this > into account. This message should reflect that. Changed to: Say yes here to add support for MediaTek PMIC Wrapper found on different MediaTek SoCs. The PMIC wrapper is a proprietary hardware to connect the PMIC. > > + * published by the Free Software Foundation. > > + * > > + * This program is distributed in the hope that it will be useful, > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > + * GNU General Public License for more details. > > + */ > > +#define DEBUG Dropped this. > > +/* > > + * FIXME: These shouldn't be here. These registers are on the PMIC, > > + * so they should be touched in the PMIC driver, not the driver > > + * granting access to it. > > + */ > > +#define MT6397_WRP_CKPDN 0x011a > > +#define MT6397_WRP_RST_CON 0x0120 > > +#define MT6397_TOP_CKCON2 0x012a > > +#define MT6397_TOP_CKCON3 0x01d4 > > We should not mix up between pmic-wrapper and pmic. I removed these. It still seems to work. Whoever wants to add that back can probably give a good reason why this must be done and how it can be abstracted properly. > > + PWRAP_RRARB_EN, > > + PWRAP_RRARB_STA0, > > + PWRAP_RRARB_STA1, > > + PWRAP_EVENT_STA, > > + PWRAP_EVENT_STACLR, > > + PWRAP_CIPHER_LOAD, > > + PWRAP_CIPHER_START, > > This registers exist on mt6589 as well, which makes me think that the > wrapper might have the same internal version. Once we know this we can replace mt8173 with v1 or whatever the version is. Should be easy enough for a cleanup patch. > > + [PWRAP_WDT_UNIT] = 0xe4, > > + [PWRAP_WDT_SRC_EN] = 0xe8, > > + [PWRAP_WDT_FLG] = 0xec, > > + [PWRAP_DEBUG_INT_SEL] = 0xf0, > > + [PWRAP_CIPHER_KEY_SEL] = 0x134, > > + [PWRAP_CIPHER_IV_SEL] = 0x138, > > + [PWRAP_CIPHER_LOAD] = 0x13c, > > + [PWRAP_CIPHER_START] = 0x140, > > + [PWRAP_CIPHER_RDY] = 0x144, > > + [PWRAP_CIPHER_MODE] = 0x148, > > + [PWRAP_CIPHER_SWRST] = 0x14c, > > + [PWRAP_DCM_EN] = 0x15c, > > + [PWRAP_DCM_DBC_PRD] = 0x160, > > +}; > > I'm not really happy with putting this arrays in here. When adding > more SoCs this will bloat up the file. Better if we put this > definitions in a header file. It's usually recommended that for #defines for only a single user no additional header file is created. Should this file really bloat up this file so much before the engineers have learned that registers should not be shifted like this, then we can still move to a separate header file. > > +static int pwrap_init_reg_clock(struct pmic_wrapper *wrp) > > +{ > > + u32 wdata; > > + u32 rdata; > > + unsigned long rate_spi; > > + int ck_mhz; > > + > > + rate_spi = clk_get_rate(wrp->clk_spi); > > + > > + if (rate_spi > 26000000) > > + ck_mhz = 26; > > + else if (rate_spi > 18) > > Hu, 18 Hz? Looks like a typo. Fixed, thanks > > + > > + switch (ck_mhz) { > > + case 18: > > + if (pwrap_is_mt8135(wrp)) > > + pwrap_writel(wrp, 0xc, PWRAP_CSHEXT); > > If the pmic-wrapper is unique to every SoC, we should think of > providing a different way to distinguish between the implementations. > Otherwise we will bloat up the code with SoC specific conditionals. I am happy to replace this with pwrap_is_v2() or even with additional function hooks in struct pmic_wrapper_type once it's clear how other pmic wrapper are different. Without this knowledge it's hard to predict what the right weapon is to abstract between SoC differences. Sascha -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH 1/2] soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs 2015-03-09 10:38 ` Sascha Hauer @ 2015-03-10 11:21 ` fan.chen 2015-03-10 12:07 ` Sascha Hauer 0 siblings, 1 reply; 8+ messages in thread From: fan.chen @ 2015-03-10 11:21 UTC (permalink / raw) To: linux-arm-kernel On Mon, 2015-03-09 at 11:38 +0100, Sascha Hauer wrote: > On Mon, Mar 09, 2015 at 09:53:31AM +0100, Matthias Brugger wrote: > > 2015-02-22 13:02 GMT+01:00 Sascha Hauer <s.hauer@pengutronix.de>: > > > From: Flora Fu <flora.fu@mediatek.com> > > > > > > new file mode 100644 > > > index 0000000..b91665a > > > --- /dev/null > > > +++ b/drivers/soc/mediatek/Kconfig > > > @@ -0,0 +1,11 @@ > > > +# > > > +# MediaTek SoC drivers > > > +# > > > +config MTK_PMIC_WRAP > > > + tristate "MediaTek PMIC Wrapper Support" > > > + depends on ARCH_MEDIATEK > > > + select REGMAP > > > + help > > > + Say yes here to add support for MediaTek PMIC Wrapper found > > > + on the MT8135 and MT8173 SoCs. The PMIC wrapper is a proprietary > > > + hardware to connect the PMIC. > > > > I have found pmic-wrapper on mt6589, mt6582 and mt6592. Most probably > > more SoCs, if not all will have a pmic-wrapper, so we should take this > > into account. This message should reflect that. > > Changed to: > > Say yes here to add support for MediaTek PMIC Wrapper found > on different MediaTek SoCs. The PMIC wrapper is a proprietary > hardware to connect the PMIC. > > > > + * published by the Free Software Foundation. > > > + * > > > + * This program is distributed in the hope that it will be useful, > > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > > + * GNU General Public License for more details. > > > + */ > > > +#define DEBUG > > Dropped this. > > > > +/* > > > + * FIXME: These shouldn't be here. These registers are on the PMIC, > > > + * so they should be touched in the PMIC driver, not the driver > > > + * granting access to it. > > > + */ > > > +#define MT6397_WRP_CKPDN 0x011a > > > +#define MT6397_WRP_RST_CON 0x0120 > > > +#define MT6397_TOP_CKCON2 0x012a > > > +#define MT6397_TOP_CKCON3 0x01d4 > > > > We should not mix up between pmic-wrapper and pmic. > > I removed these. It still seems to work. Whoever wants to add that back > can probably give a good reason why this must be done and how it can be > abstracted properly. > > > > + PWRAP_RRARB_EN, > > > + PWRAP_RRARB_STA0, > > > + PWRAP_RRARB_STA1, > > > + PWRAP_EVENT_STA, > > > + PWRAP_EVENT_STACLR, > > > + PWRAP_CIPHER_LOAD, > > > + PWRAP_CIPHER_START, > > > > This registers exist on mt6589 as well, which makes me think that the > > wrapper might have the same internal version. > > Once we know this we can replace mt8173 with v1 or whatever the version > is. Should be easy enough for a cleanup patch. > > > > + [PWRAP_WDT_UNIT] = 0xe4, > > > + [PWRAP_WDT_SRC_EN] = 0xe8, > > > + [PWRAP_WDT_FLG] = 0xec, > > > + [PWRAP_DEBUG_INT_SEL] = 0xf0, > > > + [PWRAP_CIPHER_KEY_SEL] = 0x134, > > > + [PWRAP_CIPHER_IV_SEL] = 0x138, > > > + [PWRAP_CIPHER_LOAD] = 0x13c, > > > + [PWRAP_CIPHER_START] = 0x140, > > > + [PWRAP_CIPHER_RDY] = 0x144, > > > + [PWRAP_CIPHER_MODE] = 0x148, > > > + [PWRAP_CIPHER_SWRST] = 0x14c, > > > + [PWRAP_DCM_EN] = 0x15c, > > > + [PWRAP_DCM_DBC_PRD] = 0x160, > > > +}; > > > > I'm not really happy with putting this arrays in here. When adding > > more SoCs this will bloat up the file. Better if we put this > > definitions in a header file. > > It's usually recommended that for #defines for only a single user no > additional header file is created. Should this file really bloat up this > file so much before the engineers have learned that registers should not > be shifted like this, then we can still move to a separate header file. > > > > +static int pwrap_init_reg_clock(struct pmic_wrapper *wrp) > > > +{ > > > + u32 wdata; > > > + u32 rdata; > > > + unsigned long rate_spi; > > > + int ck_mhz; > > > + > > > + rate_spi = clk_get_rate(wrp->clk_spi); > > > + > > > + if (rate_spi > 26000000) > > > + ck_mhz = 26; > > > + else if (rate_spi > 18) > > > > Hu, 18 Hz? Looks like a typo. > > Fixed, thanks > > > > + > > > + switch (ck_mhz) { > > > + case 18: > > > + if (pwrap_is_mt8135(wrp)) > > > + pwrap_writel(wrp, 0xc, PWRAP_CSHEXT); > > > > If the pmic-wrapper is unique to every SoC, we should think of > > providing a different way to distinguish between the implementations. > > Otherwise we will bloat up the code with SoC specific conditionals. > > I am happy to replace this with pwrap_is_v2() or even with additional > function hooks in struct pmic_wrapper_type once it's clear how other > pmic wrapper are different. Without this knowledge it's hard to predict > what the right weapon is to abstract between SoC differences. > > Sascha > Per function similarity, the pmic-wrapper of a new soc usually comes from an existing soc and have some modifications on it. (it does not have exactly the same version shared between SoCs so far) In this case, MT8173's pmic wrapper is derived from MT8135 and they share much common implementation. For other SOCs like 6582/6592, they would have different init flows, but the pwrap-read/write part has very similar protocol. The driver is originally intended for MT8135/MT8173 since they share quite common init flow. For other SOCs, they won't fit in current MT8135/MT173 init flow. Should we move pmic-wrapper init part to a chip-specific file and leave only common part (pmic read/write protocol) for all SoC here? ex: pwrap_readl() pwrap_writel() pwrap_is_fsm_idle() pwrap_is_fsm_vldclr() pwrap_is_sync_idle() pwrap_is_fsm_idle_and_sync_idle() pwrap_wait_for_state() pwrap_write() pwrap_read() pwrap_regmap_read() pwrap_regmap_write() Fan ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH 1/2] soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs 2015-03-10 11:21 ` fan.chen @ 2015-03-10 12:07 ` Sascha Hauer 0 siblings, 0 replies; 8+ messages in thread From: Sascha Hauer @ 2015-03-10 12:07 UTC (permalink / raw) To: linux-arm-kernel On Tue, Mar 10, 2015 at 07:21:59PM +0800, fan.chen wrote: > On Mon, 2015-03-09 at 11:38 +0100, Sascha Hauer wrote: > > > > + > > > > + switch (ck_mhz) { > > > > + case 18: > > > > + if (pwrap_is_mt8135(wrp)) > > > > + pwrap_writel(wrp, 0xc, PWRAP_CSHEXT); > > > > > > If the pmic-wrapper is unique to every SoC, we should think of > > > providing a different way to distinguish between the implementations. > > > Otherwise we will bloat up the code with SoC specific conditionals. > > > > I am happy to replace this with pwrap_is_v2() or even with additional > > function hooks in struct pmic_wrapper_type once it's clear how other > > pmic wrapper are different. Without this knowledge it's hard to predict > > what the right weapon is to abstract between SoC differences. > > > > Sascha > > > Per function similarity, the pmic-wrapper of a new soc usually comes > from an existing soc and have some modifications on it. (it does not > have exactly the same version shared between SoCs so far) So you don't have some internal versioning scheme, right? In that case the SoC name is the best we can use as a version. > In this case, MT8173's pmic wrapper is derived from MT8135 and they > share much common implementation. > For other SOCs like 6582/6592, they would have different init flows, but > the pwrap-read/write part has very similar protocol. > The driver is originally intended for MT8135/MT8173 since they share quite common init flow. Originally there were two drivers for both SoCs, it was me who merged them. > For other SOCs, they won't fit in current MT8135/MT173 init flow. > Should we move pmic-wrapper init part to a chip-specific file and leave > only common part (pmic read/write protocol) for all SoC here? ex: Putting these into separate files doesn't change much. If this becomes necessary because otherwise the driver grows too big it can always be done. For now I have created an abstraction which fits for two SoC derivates. If more derivates come then the abstraction has to grow with the situation. Yes, we don't want to end up with stuff like if (is_mt8173() || is_mt8135() || (is_mt6xxx() && !is_mt6533())). Everytime another is_mtxy() is added we have to look if it's still the right thing to be do or if function pointers in SoC specific data structs are better, or maybe a completely other approach. Sascha -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH 2/2] dt-bindings: ARM: Mediatek: document binding for the PMIC wrapper 2015-02-22 12:02 [PATCH] Mediatek PMIC wrapper support Sascha Hauer 2015-02-22 12:02 ` [PATCH 1/2] soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs Sascha Hauer @ 2015-02-22 12:02 ` Sascha Hauer 2015-03-09 5:37 ` [PATCH] Mediatek PMIC wrapper support Sascha Hauer 2 siblings, 0 replies; 8+ messages in thread From: Sascha Hauer @ 2015-02-22 12:02 UTC (permalink / raw) To: linux-arm-kernel This adds documentation for the PMIC wrapper unit found on Mediatek MT8135 and MT8173 SoCs. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> --- .../devicetree/bindings/soc/mediatek/pwrap.txt | 56 ++++++++++++++++++++++ 1 file changed, 56 insertions(+) create mode 100644 Documentation/devicetree/bindings/soc/mediatek/pwrap.txt diff --git a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt new file mode 100644 index 0000000..66cc528 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt @@ -0,0 +1,56 @@ +MediaTek PMIC Wrapper Driver + +This document describes the binding for the MediaTek PMIC wrapper. + +On MediaTek MT8135, MT8173 and other SoCs the PMIC is connected via +SPI. The SPI master interface is not directly visible to the CPU, but +only through the PMIC wrapper inside the SoC. The communication between +the SoC and the PMIC can optionally be encrypted. Also a non standard +Dual IO SPI mode can be used to increase speed. + +IP Pairing + +on MT8135 the pins of some SoC internal peripherals can be on the PMIC. +The signals of these pins are routed over the SPI bus using the pwrap +bridge. In the binding description below the properties needed for bridging +are marked with "IP Pairing". These are optional on SoCs which do not support +IP Pairing + +Required properties in pwrap device node. +- compatible: "mediatek,mt8135-pwrap" or "mediatek,mt8173-pwrap" +- interrupts: IRQ for pwrap in SOC +- reg-names: Must include the following entries: + "pwrap": Main registers base + "pwrap-bridge": bridge base (IP Pairing) +- reg: Must contain an entry for each entry in reg-names. +- reset-names: Must include the following entries: + "pwrap" + "pwrap-bridge" (IP Pairing) +- resets: Must contain an entry for each entry in reset-names. +- clock-names: Must include the following entries: + "spi": SPI bus clock + "wrap": Main module clock +- clocks: Must contain an entry for each entry in clock-names. + +Optional properities: +- pmic: Mediatek PMIC MFD is the child device of pwrap + See the following for child node definitions: + Documentation/devicetree/bindings/mfd/mt6397.txt + +Example: + pwrap: pwrap at 1000f000 { + compatible = "mediatek,mt8135-pwrap"; + reg = <0 0x1000f000 0 0x1000>, + <0 0x11017000 0 0x1000>; + reg-names = "pwrap", "pwrap-bridge"; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; + resets = <&infracfg MT8135_INFRA_PMIC_WRAP_RST>, + <&pericfg MT8135_PERI_PWRAP_BRIDGE_SW_RST>; + reset-names = "pwrap", "pwrap-bridge"; + clocks = <&clk26m>, <&clk26m>; + clock-names = "spi", "wrap"; + + pmic { + compatible = "mediatek,mt6397"; + }; + }; -- 2.1.4 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH] Mediatek PMIC wrapper support 2015-02-22 12:02 [PATCH] Mediatek PMIC wrapper support Sascha Hauer 2015-02-22 12:02 ` [PATCH 1/2] soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs Sascha Hauer 2015-02-22 12:02 ` [PATCH 2/2] dt-bindings: ARM: Mediatek: document binding for the PMIC wrapper Sascha Hauer @ 2015-03-09 5:37 ` Sascha Hauer 2 siblings, 0 replies; 8+ messages in thread From: Sascha Hauer @ 2015-03-09 5:37 UTC (permalink / raw) To: linux-arm-kernel Hi Matthias, On Sun, Feb 22, 2015 at 01:02:45PM +0100, Sascha Hauer wrote: > This series adds support for the PMIC wrapper found on MT8135 and > MT8173 SoCs. This has been sent several times already as part of > different series, this time broken out as a series only containing > the wrapper code. No further compile time dependencies. > > Matthias, I assume you can take this one through your tree, right? Are you ok with these patches? Can you take them through your tree? Sascha -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2015-03-10 12:07 UTC | newest] Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2015-02-22 12:02 [PATCH] Mediatek PMIC wrapper support Sascha Hauer 2015-02-22 12:02 ` [PATCH 1/2] soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs Sascha Hauer 2015-03-09 8:53 ` Matthias Brugger 2015-03-09 10:38 ` Sascha Hauer 2015-03-10 11:21 ` fan.chen 2015-03-10 12:07 ` Sascha Hauer 2015-02-22 12:02 ` [PATCH 2/2] dt-bindings: ARM: Mediatek: document binding for the PMIC wrapper Sascha Hauer 2015-03-09 5:37 ` [PATCH] Mediatek PMIC wrapper support Sascha Hauer
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).