* [PATCH] ARM: at91: debug: use DEBUG_UART_PHYS
@ 2015-08-08 10:11 Alexandre Belloni
2015-09-18 14:48 ` Nicolas Ferre
0 siblings, 1 reply; 4+ messages in thread
From: Alexandre Belloni @ 2015-08-08 10:11 UTC (permalink / raw)
To: linux-arm-kernel
Instead of having to add a new configuration option each time support for
new SoC is added, use CONFIG_DEBUG_UART_PHYS. For now,
CONFIG_DEBUG_UART_VIRT is automatically computed.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
arch/arm/Kconfig.debug | 41 ++++++++++++++++-------------------------
arch/arm/include/debug/at91.S | 18 ++++--------------
2 files changed, 20 insertions(+), 39 deletions(-)
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 946c8c0fa1fb..3ba23d0f5c55 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -123,29 +123,23 @@ choice
0x80020000 | 0xf0020000 | UART8
0x80024000 | 0xf0024000 | UART9
- config AT91_DEBUG_LL_DBGU0
- bool "Kernel low-level debugging on rm9200, 9260/9g20, 9261/9g10, 9rl, 9x5, 9n12"
- select DEBUG_AT91_UART
+ config DEBUG_AT91_UART
+ bool "Kernel low-level debugging on Atmel SoCs"
depends on ARCH_AT91
- depends on SOC_AT91RM9200 || SOC_AT91SAM9
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the serial port on atmel devices.
- config AT91_DEBUG_LL_DBGU1
- bool "Kernel low-level debugging on 9263, 9g45 and sama5d3"
- select DEBUG_AT91_UART
- depends on ARCH_AT91
- depends on SOC_AT91SAM9 || SOC_SAMA5
+ SOC DEBUG_UART_PHYS DEBUG_UART_VIRT PORT
+ rm9200, 9260/9g20, 0xfffff200 0xfefff200 DBGU
+ 9261/9g10, 9rl
+ 9263, 9g45, sama5d3 0xffffee00 0xfeffee00 DBGU
+ sama5d4 0xfc00c000 0xfb00c000 USART3
+ sama5d4 0xfc069000 0xfb069000 DBGU
+ sama5d2 0xf8020000 0xf7020000 UART1
- config AT91_DEBUG_LL_DBGU2
- bool "Kernel low-level debugging on sama5d4"
- select DEBUG_AT91_UART
- depends on ARCH_AT91
- depends on SOC_SAMA5
-
- config AT91_DEBUG_LL_DBGU3
- bool "Kernel low-level debugging on sama5d2"
- select DEBUG_AT91_UART
- depends on ARCH_AT91
- depends on SOC_SAMA5
+ Please adjust DEBUG_UART_PHYS configuration options based on
+ your needs.
config DEBUG_BCM2835
bool "Kernel low-level debugging on BCM2835 PL011 UART"
@@ -1242,10 +1236,6 @@ choice
endchoice
-config DEBUG_AT91_UART
- bool
- depends on ARCH_AT91
-
config DEBUG_EXYNOS_UART
bool
@@ -1476,7 +1466,8 @@ config DEBUG_UART_PHYS
DEBUG_RMOBILE_SCIFA0 || DEBUG_RMOBILE_SCIFA1 || \
DEBUG_RMOBILE_SCIFA4 || DEBUG_S3C24XX_UART || \
DEBUG_UART_BCM63XX || DEBUG_ASM9260_UART || \
- DEBUG_SIRFSOC_UART || DEBUG_DIGICOLOR_UA0
+ DEBUG_SIRFSOC_UART || DEBUG_DIGICOLOR_UA0 || \
+ DEBUG_AT91_UART
config DEBUG_UART_VIRT
hex "Virtual base address of debug UART"
diff --git a/arch/arm/include/debug/at91.S b/arch/arm/include/debug/at91.S
index 2556a8801c8c..43243be94cfc 100644
--- a/arch/arm/include/debug/at91.S
+++ b/arch/arm/include/debug/at91.S
@@ -9,32 +9,22 @@
*
*/
-#if defined(CONFIG_AT91_DEBUG_LL_DBGU0)
-#define AT91_DBGU 0xfffff200 /* AT91_BASE_DBGU0 */
-#elif defined(CONFIG_AT91_DEBUG_LL_DBGU1)
-#define AT91_DBGU 0xffffee00 /* AT91_BASE_DBGU1 */
-#elif defined(CONFIG_AT91_DEBUG_LL_DBGU2)
-/* On sama5d4, use USART3 as low level serial console */
-#define AT91_DBGU 0xfc00c000 /* SAMA5D4_BASE_USART3 */
-#else
-/* On sama5d2, use UART1 as low level serial console */
-#define AT91_DBGU 0xf8020000
-#endif
-
#ifdef CONFIG_MMU
#define AT91_IO_P2V(x) ((x) - 0x01000000)
#else
#define AT91_IO_P2V(x) (x)
#endif
+#define CONFIG_DEBUG_UART_VIRT AT91_IO_P2V(CONFIG_DEBUG_UART_PHYS)
+
#define AT91_DBGU_SR (0x14) /* Status Register */
#define AT91_DBGU_THR (0x1c) /* Transmitter Holding Register */
#define AT91_DBGU_TXRDY (1 << 1) /* Transmitter Ready */
#define AT91_DBGU_TXEMPTY (1 << 9) /* Transmitter Empty */
.macro addruart, rp, rv, tmp
- ldr \rp, =AT91_DBGU @ System peripherals (phys address)
- ldr \rv, =AT91_IO_P2V(AT91_DBGU) @ System peripherals (virt address)
+ ldr \rp, =CONFIG_DEBUG_UART_PHYS @ System peripherals (phys address)
+ ldr \rv, =CONFIG_DEBUG_UART_VIRT @ System peripherals (virt address)
.endm
.macro senduart,rd,rx
--
2.1.4
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH] ARM: at91: debug: use DEBUG_UART_PHYS
2015-08-08 10:11 [PATCH] ARM: at91: debug: use DEBUG_UART_PHYS Alexandre Belloni
@ 2015-09-18 14:48 ` Nicolas Ferre
2015-09-18 22:13 ` Alexandre Belloni
0 siblings, 1 reply; 4+ messages in thread
From: Nicolas Ferre @ 2015-09-18 14:48 UTC (permalink / raw)
To: linux-arm-kernel
Le 08/08/2015 12:11, Alexandre Belloni a ?crit :
> Instead of having to add a new configuration option each time support for
> new SoC is added, use CONFIG_DEBUG_UART_PHYS. For now,
> CONFIG_DEBUG_UART_VIRT is automatically computed.
>
> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
> ---
> arch/arm/Kconfig.debug | 41 ++++++++++++++++-------------------------
> arch/arm/include/debug/at91.S | 18 ++++--------------
> 2 files changed, 20 insertions(+), 39 deletions(-)
>
> diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
> index 946c8c0fa1fb..3ba23d0f5c55 100644
> --- a/arch/arm/Kconfig.debug
> +++ b/arch/arm/Kconfig.debug
> @@ -123,29 +123,23 @@ choice
> 0x80020000 | 0xf0020000 | UART8
> 0x80024000 | 0xf0024000 | UART9
>
> - config AT91_DEBUG_LL_DBGU0
> - bool "Kernel low-level debugging on rm9200, 9260/9g20, 9261/9g10, 9rl, 9x5, 9n12"
> - select DEBUG_AT91_UART
> + config DEBUG_AT91_UART
> + bool "Kernel low-level debugging on Atmel SoCs"
> depends on ARCH_AT91
> - depends on SOC_AT91RM9200 || SOC_AT91SAM9
> + help
> + Say Y here if you want the debug print routines to direct
> + their output to the serial port on atmel devices.
>
> - config AT91_DEBUG_LL_DBGU1
> - bool "Kernel low-level debugging on 9263, 9g45 and sama5d3"
> - select DEBUG_AT91_UART
> - depends on ARCH_AT91
> - depends on SOC_AT91SAM9 || SOC_SAMA5
> + SOC DEBUG_UART_PHYS DEBUG_UART_VIRT PORT
> + rm9200, 9260/9g20, 0xfffff200 0xfefff200 DBGU
> + 9261/9g10, 9rl
> + 9263, 9g45, sama5d3 0xffffee00 0xfeffee00 DBGU
> + sama5d4 0xfc00c000 0xfb00c000 USART3
> + sama5d4 0xfc069000 0xfb069000 DBGU
This last one must be sama5d3, mustn't it?
Otherwise I'm okay:
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
> + sama5d2 0xf8020000 0xf7020000 UART1
>
> - config AT91_DEBUG_LL_DBGU2
> - bool "Kernel low-level debugging on sama5d4"
> - select DEBUG_AT91_UART
> - depends on ARCH_AT91
> - depends on SOC_SAMA5
> -
> - config AT91_DEBUG_LL_DBGU3
> - bool "Kernel low-level debugging on sama5d2"
> - select DEBUG_AT91_UART
> - depends on ARCH_AT91
> - depends on SOC_SAMA5
> + Please adjust DEBUG_UART_PHYS configuration options based on
> + your needs.
>
> config DEBUG_BCM2835
> bool "Kernel low-level debugging on BCM2835 PL011 UART"
> @@ -1242,10 +1236,6 @@ choice
>
> endchoice
>
> -config DEBUG_AT91_UART
> - bool
> - depends on ARCH_AT91
> -
> config DEBUG_EXYNOS_UART
> bool
>
> @@ -1476,7 +1466,8 @@ config DEBUG_UART_PHYS
> DEBUG_RMOBILE_SCIFA0 || DEBUG_RMOBILE_SCIFA1 || \
> DEBUG_RMOBILE_SCIFA4 || DEBUG_S3C24XX_UART || \
> DEBUG_UART_BCM63XX || DEBUG_ASM9260_UART || \
> - DEBUG_SIRFSOC_UART || DEBUG_DIGICOLOR_UA0
> + DEBUG_SIRFSOC_UART || DEBUG_DIGICOLOR_UA0 || \
> + DEBUG_AT91_UART
>
> config DEBUG_UART_VIRT
> hex "Virtual base address of debug UART"
> diff --git a/arch/arm/include/debug/at91.S b/arch/arm/include/debug/at91.S
> index 2556a8801c8c..43243be94cfc 100644
> --- a/arch/arm/include/debug/at91.S
> +++ b/arch/arm/include/debug/at91.S
> @@ -9,32 +9,22 @@
> *
> */
>
> -#if defined(CONFIG_AT91_DEBUG_LL_DBGU0)
> -#define AT91_DBGU 0xfffff200 /* AT91_BASE_DBGU0 */
> -#elif defined(CONFIG_AT91_DEBUG_LL_DBGU1)
> -#define AT91_DBGU 0xffffee00 /* AT91_BASE_DBGU1 */
> -#elif defined(CONFIG_AT91_DEBUG_LL_DBGU2)
> -/* On sama5d4, use USART3 as low level serial console */
> -#define AT91_DBGU 0xfc00c000 /* SAMA5D4_BASE_USART3 */
> -#else
> -/* On sama5d2, use UART1 as low level serial console */
> -#define AT91_DBGU 0xf8020000
> -#endif
> -
> #ifdef CONFIG_MMU
> #define AT91_IO_P2V(x) ((x) - 0x01000000)
> #else
> #define AT91_IO_P2V(x) (x)
> #endif
>
> +#define CONFIG_DEBUG_UART_VIRT AT91_IO_P2V(CONFIG_DEBUG_UART_PHYS)
> +
> #define AT91_DBGU_SR (0x14) /* Status Register */
> #define AT91_DBGU_THR (0x1c) /* Transmitter Holding Register */
> #define AT91_DBGU_TXRDY (1 << 1) /* Transmitter Ready */
> #define AT91_DBGU_TXEMPTY (1 << 9) /* Transmitter Empty */
>
> .macro addruart, rp, rv, tmp
> - ldr \rp, =AT91_DBGU @ System peripherals (phys address)
> - ldr \rv, =AT91_IO_P2V(AT91_DBGU) @ System peripherals (virt address)
> + ldr \rp, =CONFIG_DEBUG_UART_PHYS @ System peripherals (phys address)
> + ldr \rv, =CONFIG_DEBUG_UART_VIRT @ System peripherals (virt address)
> .endm
>
> .macro senduart,rd,rx
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH] ARM: at91: debug: use DEBUG_UART_PHYS
2015-09-18 14:48 ` Nicolas Ferre
@ 2015-09-18 22:13 ` Alexandre Belloni
2015-09-21 14:22 ` Nicolas Ferre
0 siblings, 1 reply; 4+ messages in thread
From: Alexandre Belloni @ 2015-09-18 22:13 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On 18/09/2015 at 16:48:43 +0200, Nicolas Ferre wrote :
> > - config AT91_DEBUG_LL_DBGU1
> > - bool "Kernel low-level debugging on 9263, 9g45 and sama5d3"
> > - select DEBUG_AT91_UART
> > - depends on ARCH_AT91
> > - depends on SOC_AT91SAM9 || SOC_SAMA5
> > + SOC DEBUG_UART_PHYS DEBUG_UART_VIRT PORT
> > + rm9200, 9260/9g20, 0xfffff200 0xfefff200 DBGU
> > + 9261/9g10, 9rl
> > + 9263, 9g45, sama5d3 0xffffee00 0xfeffee00 DBGU
> > + sama5d4 0xfc00c000 0xfb00c000 USART3
> > + sama5d4 0xfc069000 0xfb069000 DBGU
>
> This last one must be sama5d3, mustn't it?
>
No, that is the DBGU for sama5d4, sama5d3 is mentionned and is at
0xffffee00. I added it in case someone doesn't use USART3 for debugging
and wants to use the DBGU. I actually doubt it may happen but we never
now. I can remove it in a v2 if you prefer.
> Otherwise I'm okay:
> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
>
> > + sama5d2 0xf8020000 0xf7020000 UART1
> >
> > - config AT91_DEBUG_LL_DBGU2
> > - bool "Kernel low-level debugging on sama5d4"
> > - select DEBUG_AT91_UART
> > - depends on ARCH_AT91
> > - depends on SOC_SAMA5
> > -
> > - config AT91_DEBUG_LL_DBGU3
> > - bool "Kernel low-level debugging on sama5d2"
> > - select DEBUG_AT91_UART
> > - depends on ARCH_AT91
> > - depends on SOC_SAMA5
> > + Please adjust DEBUG_UART_PHYS configuration options based on
> > + your needs.
> >
> > config DEBUG_BCM2835
> > bool "Kernel low-level debugging on BCM2835 PL011 UART"
> > @@ -1242,10 +1236,6 @@ choice
> >
> > endchoice
> >
> > -config DEBUG_AT91_UART
> > - bool
> > - depends on ARCH_AT91
> > -
> > config DEBUG_EXYNOS_UART
> > bool
> >
> > @@ -1476,7 +1466,8 @@ config DEBUG_UART_PHYS
> > DEBUG_RMOBILE_SCIFA0 || DEBUG_RMOBILE_SCIFA1 || \
> > DEBUG_RMOBILE_SCIFA4 || DEBUG_S3C24XX_UART || \
> > DEBUG_UART_BCM63XX || DEBUG_ASM9260_UART || \
> > - DEBUG_SIRFSOC_UART || DEBUG_DIGICOLOR_UA0
> > + DEBUG_SIRFSOC_UART || DEBUG_DIGICOLOR_UA0 || \
> > + DEBUG_AT91_UART
> >
> > config DEBUG_UART_VIRT
> > hex "Virtual base address of debug UART"
> > diff --git a/arch/arm/include/debug/at91.S b/arch/arm/include/debug/at91.S
> > index 2556a8801c8c..43243be94cfc 100644
> > --- a/arch/arm/include/debug/at91.S
> > +++ b/arch/arm/include/debug/at91.S
> > @@ -9,32 +9,22 @@
> > *
> > */
> >
> > -#if defined(CONFIG_AT91_DEBUG_LL_DBGU0)
> > -#define AT91_DBGU 0xfffff200 /* AT91_BASE_DBGU0 */
> > -#elif defined(CONFIG_AT91_DEBUG_LL_DBGU1)
> > -#define AT91_DBGU 0xffffee00 /* AT91_BASE_DBGU1 */
> > -#elif defined(CONFIG_AT91_DEBUG_LL_DBGU2)
> > -/* On sama5d4, use USART3 as low level serial console */
> > -#define AT91_DBGU 0xfc00c000 /* SAMA5D4_BASE_USART3 */
> > -#else
> > -/* On sama5d2, use UART1 as low level serial console */
> > -#define AT91_DBGU 0xf8020000
> > -#endif
> > -
> > #ifdef CONFIG_MMU
> > #define AT91_IO_P2V(x) ((x) - 0x01000000)
> > #else
> > #define AT91_IO_P2V(x) (x)
> > #endif
> >
> > +#define CONFIG_DEBUG_UART_VIRT AT91_IO_P2V(CONFIG_DEBUG_UART_PHYS)
> > +
> > #define AT91_DBGU_SR (0x14) /* Status Register */
> > #define AT91_DBGU_THR (0x1c) /* Transmitter Holding Register */
> > #define AT91_DBGU_TXRDY (1 << 1) /* Transmitter Ready */
> > #define AT91_DBGU_TXEMPTY (1 << 9) /* Transmitter Empty */
> >
> > .macro addruart, rp, rv, tmp
> > - ldr \rp, =AT91_DBGU @ System peripherals (phys address)
> > - ldr \rv, =AT91_IO_P2V(AT91_DBGU) @ System peripherals (virt address)
> > + ldr \rp, =CONFIG_DEBUG_UART_PHYS @ System peripherals (phys address)
> > + ldr \rv, =CONFIG_DEBUG_UART_VIRT @ System peripherals (virt address)
> > .endm
> >
> > .macro senduart,rd,rx
> >
>
>
> --
> Nicolas Ferre
--
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH] ARM: at91: debug: use DEBUG_UART_PHYS
2015-09-18 22:13 ` Alexandre Belloni
@ 2015-09-21 14:22 ` Nicolas Ferre
0 siblings, 0 replies; 4+ messages in thread
From: Nicolas Ferre @ 2015-09-21 14:22 UTC (permalink / raw)
To: linux-arm-kernel
Le 19/09/2015 00:13, Alexandre Belloni a ?crit :
> Hi,
>
> On 18/09/2015 at 16:48:43 +0200, Nicolas Ferre wrote :
>>> - config AT91_DEBUG_LL_DBGU1
>>> - bool "Kernel low-level debugging on 9263, 9g45 and sama5d3"
>>> - select DEBUG_AT91_UART
>>> - depends on ARCH_AT91
>>> - depends on SOC_AT91SAM9 || SOC_SAMA5
>>> + SOC DEBUG_UART_PHYS DEBUG_UART_VIRT PORT
>>> + rm9200, 9260/9g20, 0xfffff200 0xfefff200 DBGU
>>> + 9261/9g10, 9rl
>>> + 9263, 9g45, sama5d3 0xffffee00 0xfeffee00 DBGU
>>> + sama5d4 0xfc00c000 0xfb00c000 USART3
>>> + sama5d4 0xfc069000 0xfb069000 DBGU
>>
>> This last one must be sama5d3, mustn't it?
>>
>
> No, that is the DBGU for sama5d4, sama5d3 is mentionned and is at
> 0xffffee00. I added it in case someone doesn't use USART3 for debugging
> and wants to use the DBGU. I actually doubt it may happen but we never
> now. I can remove it in a v2 if you prefer.
Ok, I understand now.
No need for a v2, I take this one in at91-4.4-soc branch.
Thanks, bye,
>
>> Otherwise I'm okay:
>> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
>>
>>> + sama5d2 0xf8020000 0xf7020000 UART1
>>>
>>> - config AT91_DEBUG_LL_DBGU2
>>> - bool "Kernel low-level debugging on sama5d4"
>>> - select DEBUG_AT91_UART
>>> - depends on ARCH_AT91
>>> - depends on SOC_SAMA5
>>> -
>>> - config AT91_DEBUG_LL_DBGU3
>>> - bool "Kernel low-level debugging on sama5d2"
>>> - select DEBUG_AT91_UART
>>> - depends on ARCH_AT91
>>> - depends on SOC_SAMA5
>>> + Please adjust DEBUG_UART_PHYS configuration options based on
>>> + your needs.
>>>
>>> config DEBUG_BCM2835
>>> bool "Kernel low-level debugging on BCM2835 PL011 UART"
>>> @@ -1242,10 +1236,6 @@ choice
>>>
>>> endchoice
>>>
>>> -config DEBUG_AT91_UART
>>> - bool
>>> - depends on ARCH_AT91
>>> -
>>> config DEBUG_EXYNOS_UART
>>> bool
>>>
>>> @@ -1476,7 +1466,8 @@ config DEBUG_UART_PHYS
>>> DEBUG_RMOBILE_SCIFA0 || DEBUG_RMOBILE_SCIFA1 || \
>>> DEBUG_RMOBILE_SCIFA4 || DEBUG_S3C24XX_UART || \
>>> DEBUG_UART_BCM63XX || DEBUG_ASM9260_UART || \
>>> - DEBUG_SIRFSOC_UART || DEBUG_DIGICOLOR_UA0
>>> + DEBUG_SIRFSOC_UART || DEBUG_DIGICOLOR_UA0 || \
>>> + DEBUG_AT91_UART
>>>
>>> config DEBUG_UART_VIRT
>>> hex "Virtual base address of debug UART"
>>> diff --git a/arch/arm/include/debug/at91.S b/arch/arm/include/debug/at91.S
>>> index 2556a8801c8c..43243be94cfc 100644
>>> --- a/arch/arm/include/debug/at91.S
>>> +++ b/arch/arm/include/debug/at91.S
>>> @@ -9,32 +9,22 @@
>>> *
>>> */
>>>
>>> -#if defined(CONFIG_AT91_DEBUG_LL_DBGU0)
>>> -#define AT91_DBGU 0xfffff200 /* AT91_BASE_DBGU0 */
>>> -#elif defined(CONFIG_AT91_DEBUG_LL_DBGU1)
>>> -#define AT91_DBGU 0xffffee00 /* AT91_BASE_DBGU1 */
>>> -#elif defined(CONFIG_AT91_DEBUG_LL_DBGU2)
>>> -/* On sama5d4, use USART3 as low level serial console */
>>> -#define AT91_DBGU 0xfc00c000 /* SAMA5D4_BASE_USART3 */
>>> -#else
>>> -/* On sama5d2, use UART1 as low level serial console */
>>> -#define AT91_DBGU 0xf8020000
>>> -#endif
>>> -
>>> #ifdef CONFIG_MMU
>>> #define AT91_IO_P2V(x) ((x) - 0x01000000)
>>> #else
>>> #define AT91_IO_P2V(x) (x)
>>> #endif
>>>
>>> +#define CONFIG_DEBUG_UART_VIRT AT91_IO_P2V(CONFIG_DEBUG_UART_PHYS)
>>> +
>>> #define AT91_DBGU_SR (0x14) /* Status Register */
>>> #define AT91_DBGU_THR (0x1c) /* Transmitter Holding Register */
>>> #define AT91_DBGU_TXRDY (1 << 1) /* Transmitter Ready */
>>> #define AT91_DBGU_TXEMPTY (1 << 9) /* Transmitter Empty */
>>>
>>> .macro addruart, rp, rv, tmp
>>> - ldr \rp, =AT91_DBGU @ System peripherals (phys address)
>>> - ldr \rv, =AT91_IO_P2V(AT91_DBGU) @ System peripherals (virt address)
>>> + ldr \rp, =CONFIG_DEBUG_UART_PHYS @ System peripherals (phys address)
>>> + ldr \rv, =CONFIG_DEBUG_UART_VIRT @ System peripherals (virt address)
>>> .endm
>>>
>>> .macro senduart,rd,rx
>>>
>>
>>
>> --
>> Nicolas Ferre
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2015-09-21 14:22 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-08-08 10:11 [PATCH] ARM: at91: debug: use DEBUG_UART_PHYS Alexandre Belloni
2015-09-18 14:48 ` Nicolas Ferre
2015-09-18 22:13 ` Alexandre Belloni
2015-09-21 14:22 ` Nicolas Ferre
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).