linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: Stefan Wahren <stefan.wahren@i2se.com>
To: Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	Florian Fainelli <f.fainelli@gmail.com>,
	Ray Jui <rjui@broadcom.com>,
	Scott Branden <sbranden@broadcom.com>,
	Eric Anholt <eric@anholt.net>
Cc: Gottfried Haider <gottfried.haider@gmail.com>,
	devicetree@vger.kernel.org,
	Stefan Wahren <stefan.wahren@i2se.com>,
	Phil Elwell <phil@raspberrypi.org>,
	bcm-kernel-feedback-list@broadcom.com,
	Peter Robinson <pbrobinson@gmail.com>,
	linux-arm-kernel@lists.infradead.org,
	linux-rpi-kernel@lists.infradead.org
Subject: [PATCH 6/6] ARM: dts: bcm283x: Add missing GPIO line names
Date: Sat, 12 Jan 2019 13:43:28 +0100	[thread overview]
Message-ID: <1547297008-2740-7-git-send-email-stefan.wahren@i2se.com> (raw)
In-Reply-To: <1547297008-2740-1-git-send-email-stefan.wahren@i2se.com>

The GPIO sysfs is deprecated and disabled in the defconfig files.
So in order to motivate the usage of the new GPIO character device API
add the missing GPIO line names for Raspberry Pi 2 and 3. In the lack
of full schematics i would leave all undocumented pins as unnamed.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
---
 arch/arm/boot/dts/bcm2836-rpi-2-b.dts      | 66 ++++++++++++++++++++++++++++
 arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts | 70 ++++++++++++++++++++++++++++++
 arch/arm/boot/dts/bcm2837-rpi-3-b.dts      | 70 ++++++++++++++++++++++++++++++
 3 files changed, 206 insertions(+)

diff --git a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
index 871fc4a..7b4e651 100644
--- a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
+++ b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
@@ -28,6 +28,72 @@
 };
 
 &gpio {
+	/*
+	 * Taken from rpi_SCH_2b_1p2_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "SDA0",
+			  "SCL0",
+			  "", /* GPIO30 */
+			  "LAN_RUN",
+			  "CAM_GPIO1",
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "PWR_LOW_N",
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "USB_LIMIT",
+			  "", /* GPIO39 */
+			  "PWM0_OUT",
+			  "CAM_GPIO0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  "ETHCLK",
+			  "PWM1_OUT",
+			  "HDMI_HPD_N",
+			  "STATUS_LED",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
 	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
index d3ec6cd..c6fa34c 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
@@ -52,6 +52,76 @@
 	};
 };
 
+&gpio {
+	/*
+	 * Taken from rpi_SCH_3bplus_1p0_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "HDMI_HPD_N",
+			  "STATUS_LED_G",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  "PWM0_OUT",
+			  "PWM1_OUT",
+			  "ETHCLK",
+			  "WIFI_CLK",
+			  "SDA0",
+			  "SCL0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+};
+
 &hdmi {
 	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
 };
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
index 31b1c03..ce71f57 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
@@ -47,6 +47,76 @@
 	};
 };
 
+&gpio {
+	/*
+	 * Taken from rpi_SCH_3b_1p2_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "", /* GPIO 28 */
+			  "LAN_RUN_BOOT",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  "PWM0_OUT",
+			  "PWM1_OUT",
+			  "ETHCLK",
+			  "WIFI_CLK",
+			  "SDA0",
+			  "SCL0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply	other threads:[~2019-01-12 12:45 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-01-12 12:43 [PATCH 0/6] ARM: dts: bcm283x: Several DTS improvements Stefan Wahren
2019-01-12 12:43 ` [PATCH 1/6] ARM: dts: bcm283x: Fix DTC warning for memory node Stefan Wahren
2019-01-21  4:59   ` Peter Robinson
2019-01-12 12:43 ` [PATCH 2/6] ARM: dts: bcm2835-rpi: Drop unnecessary #address-cells/#size-cells Stefan Wahren
2019-01-12 12:43 ` [PATCH 3/6] ARM: dts: bcm2835: Fix labels for GPIO 0,1 Stefan Wahren
2019-01-12 12:43 ` [PATCH 4/6] ARM: dts: bcm2837-rpi-3-b: Use consistent label for HDMI hotplug Stefan Wahren
2019-01-21  5:02   ` Peter Robinson
2019-01-12 12:43 ` [PATCH 5/6] ARM: dts: bcm2837-rpi-3-b-plus: Clarify label for STATUS_LED Stefan Wahren
2019-01-21  5:00   ` Peter Robinson
2019-01-12 12:43 ` Stefan Wahren [this message]
2019-01-21  4:52   ` [PATCH 6/6] ARM: dts: bcm283x: Add missing GPIO line names Peter Robinson
2019-01-21 20:27   ` Eric Anholt
2019-01-22  7:57 ` [PATCH 0/6] ARM: dts: bcm283x: Several DTS improvements Stefan Wahren

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1547297008-2740-7-git-send-email-stefan.wahren@i2se.com \
    --to=stefan.wahren@i2se.com \
    --cc=bcm-kernel-feedback-list@broadcom.com \
    --cc=devicetree@vger.kernel.org \
    --cc=eric@anholt.net \
    --cc=f.fainelli@gmail.com \
    --cc=gottfried.haider@gmail.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-rpi-kernel@lists.infradead.org \
    --cc=mark.rutland@arm.com \
    --cc=pbrobinson@gmail.com \
    --cc=phil@raspberrypi.org \
    --cc=rjui@broadcom.com \
    --cc=robh+dt@kernel.org \
    --cc=sbranden@broadcom.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).