From: Chunfeng Yun <chunfeng.yun@mediatek.com>
To: Rob Herring <robh+dt@kernel.org>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>,
devicetree@vger.kernel.org, Hans de Goede <hdegoede@redhat.com>,
Badhri Jagan Sridharan <badhri@google.com>,
Linus Walleij <linus.walleij@linaro.org>,
linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org,
Biju Das <biju.das@bp.renesas.com>,
Matthias Brugger <matthias.bgg@gmail.com>,
Andy Shevchenko <andy.shevchenko@gmail.com>,
linux-mediatek@lists.infradead.org,
Min Guo <min.guo@mediatek.com>,
Chunfeng Yun <chunfeng.yun@mediatek.com>,
Adam Thomson <Adam.Thomson.Opensource@diasemi.com>,
linux-arm-kernel@lists.infradead.org, Li Jun <jun.li@nxp.com>
Subject: [PATCH v5 2/6] dt-bindings: usb: add binding for Type-B GPIO connector driver
Date: Tue, 14 May 2019 16:47:19 +0800 [thread overview]
Message-ID: <1557823643-8616-3-git-send-email-chunfeng.yun@mediatek.com> (raw)
In-Reply-To: <1557823643-8616-1-git-send-email-chunfeng.yun@mediatek.com>
It's used to support dual role switch via GPIO when use Type-B
receptacle, typically the USB ID pin is connected to an input
GPIO pin
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v5 changes:
1. treat type-B connector as child device of USB controller's, but not
as a separate virtual device, suggested by Rob
2. put connector's port node under connector node, suggested by Rob
v4 no changes
v3 changes:
1. treat type-B connector as a virtual device, but not child device of
USB controller's
v2 changes:
1. new patch to make binding clear suggested by Hans
---
.../bindings/usb/typeb-conn-gpio.txt | 42 +++++++++++++++++++
1 file changed, 42 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/typeb-conn-gpio.txt
diff --git a/Documentation/devicetree/bindings/usb/typeb-conn-gpio.txt b/Documentation/devicetree/bindings/usb/typeb-conn-gpio.txt
new file mode 100644
index 000000000000..20dd3499a348
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/typeb-conn-gpio.txt
@@ -0,0 +1,42 @@
+USB Type-B GPIO Connector
+
+This is used to switch dual role mode from the USB ID pin connected to
+an input GPIO pin.
+
+Required properties:
+- compatible : should include "linux,typeb-conn-gpio" and "usb-b-connector".
+- id-gpios, vbus-gpios : either one of them must be present, and both
+ can be present as well.
+- vbus-supply : can be present if needed when supports dual role mode or
+ host mode.
+ see connector/usb-connector.txt
+
+Sub-nodes:
+- port : should be present.
+ see graph.txt
+
+Example:
+
+&mtu3 {
+ status = "okay";
+
+ connector {
+ compatible = "linux,typeb-conn-gpio", "usb-b-connector";
+ label = "micro-USB";
+ type = "micro";
+ id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>;
+ vbus-supply = <&usb_p0_vbus>;
+
+ port {
+ bconn_ep: endpoint@0 {
+ remote-endpoint = <&usb_role_sw>;
+ };
+ };
+ };
+
+ port {
+ usb_role_sw: endpoint@0 {
+ remote-endpoint = <&bconn_ep>;
+ };
+ };
+};
--
2.21.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-05-14 8:48 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-14 8:47 [v5 PATCH 0/6] add USB Type-B GPIO connector driver Chunfeng Yun
2019-05-14 8:47 ` [PATCH v5 1/6] dt-bindings: connector: add optional properties for Type-B Chunfeng Yun
2019-05-14 8:47 ` Chunfeng Yun [this message]
2019-05-14 18:12 ` [PATCH v5 2/6] dt-bindings: usb: add binding for Type-B GPIO connector driver Rob Herring
2019-05-15 9:36 ` Chunfeng Yun
2019-05-14 8:47 ` [PATCH v5 3/6] dt-bindings: usb: mtu3: add properties about USB Role Switch Chunfeng Yun
2019-05-14 18:17 ` Rob Herring
2019-05-14 8:47 ` [PATCH v5 4/6] usb: roles: add API to get usb_role_switch by node Chunfeng Yun
2019-05-17 10:37 ` Heikki Krogerus
2019-05-17 13:05 ` Heikki Krogerus
2019-05-20 2:39 ` Chunfeng Yun
2019-05-20 8:03 ` Heikki Krogerus
2019-05-20 8:06 ` Biju Das
2019-05-20 8:36 ` Heikki Krogerus
2019-05-20 9:45 ` Biju Das
2019-05-21 7:35 ` Chunfeng Yun
2019-05-21 10:33 ` Heikki Krogerus
2019-05-22 3:37 ` Chunfeng Yun
2019-05-21 9:58 ` Heikki Krogerus
2019-05-22 8:05 ` Biju Das
2019-05-22 9:30 ` Chunfeng Yun
2019-05-22 10:55 ` Biju Das
2019-05-22 14:26 ` Heikki Krogerus
2019-05-22 14:57 ` Biju Das
2019-05-24 12:44 ` Heikki Krogerus
2019-05-27 3:08 ` Chunfeng Yun
2019-05-28 6:52 ` Biju Das
2019-05-28 9:23 ` Chunfeng Yun
2019-05-23 10:16 ` Chunfeng Yun
2019-05-24 11:40 ` Heikki Krogerus
2019-05-27 3:07 ` Chunfeng Yun
2019-05-27 10:45 ` Heikki Krogerus
2019-05-14 8:47 ` [PATCH v5 5/6] usb: roles: add USB Type-B GPIO connector driver Chunfeng Yun
2019-05-20 8:31 ` Heikki Krogerus
2019-05-21 7:44 ` Chunfeng Yun
2019-05-14 8:47 ` [PATCH v5 6/6] usb: mtu3: register a USB Role Switch for dual role mode Chunfeng Yun
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1557823643-8616-3-git-send-email-chunfeng.yun@mediatek.com \
--to=chunfeng.yun@mediatek.com \
--cc=Adam.Thomson.Opensource@diasemi.com \
--cc=andy.shevchenko@gmail.com \
--cc=badhri@google.com \
--cc=biju.das@bp.renesas.com \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=hdegoede@redhat.com \
--cc=heikki.krogerus@linux.intel.com \
--cc=jun.li@nxp.com \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux-usb@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=matthias.bgg@gmail.com \
--cc=min.guo@mediatek.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).