[PATCH RESEND 1/4] dt-bindings: thermal: imx8mm-thermal: Add binding doc for i.MX8MM

[PATCH RESEND 1/4] dt-bindings: thermal: imx8mm-thermal: Add binding doc for i.MX8MM

[Anson Huang]

Add thermal binding doc for Freescale's i.MX8MM Thermal Monitoring Unit.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/thermal/imx8mm-thermal.txt        | 15 +++++++++++++++
 1 file changed, 15 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/imx8mm-thermal.txt

diff --git a/Documentation/devicetree/bindings/thermal/imx8mm-thermal.txt b/Documentation/devicetree/bindings/thermal/imx8mm-thermal.txt
new file mode 100644
index 0000000..d09ae82
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/imx8mm-thermal.txt
@@ -0,0 +1,15 @@
+* Thermal Monitoring Unit (TMU) on Freescale i.MX8MM SoC
+
+Required properties:
+- compatible : Must be "fsl,imx8mm-tmu".
+- reg : Address range of TMU registers.
+- clocks : TMU's clock source.
+- #thermal-sensor-cells : Should be 0. See ./thermal.txt for a description.
+
+Example:
+tmu: tmu@30260000 {
+	compatible = "fsl,imx8mm-tmu";
+	reg = <0x30260000 0x10000>;
+	clocks = <&clk IMX8MM_CLK_TMU_ROOT>;
+	#thermal-sensor-cells = <0>;
+};
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH RESEND 2/4] thermal: imx8mm: Add support for i.MX8MM thermal monitoring unit

[Anson Huang]

i.MX8MM has a thermal monitoring unit(TMU) inside, it ONLY has one
sensor for CPU, add support for reading immediate temperature of
this sensor.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 drivers/thermal/Kconfig          |  10 +++
 drivers/thermal/Makefile         |   1 +
 drivers/thermal/imx8mm_thermal.c | 134 +++++++++++++++++++++++++++++++++++++++
 3 files changed, 145 insertions(+)
 create mode 100644 drivers/thermal/imx8mm_thermal.c

diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 129b9ed..e09ff16 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -233,6 +233,16 @@ config IMX_THERMAL
 	  cpufreq is used as the cooling device to throttle CPUs when the
 	  passive trip is crossed.
 
+config IMX8MM_THERMAL
+	tristate "Temperature sensor driver for Freescale i.MX8MM SoC"
+	depends on ARCH_MXC
+	depends on OF
+	help
+	  Support for Thermal Monitoring Unit (TMU) found on Freescale i.MX8MM SoC.
+	  It supports one critical trip point and one passive trip point. The
+	  cpufreq is used as the cooling device to throttle CPUs when the passive
+	  trip is crossed.
+
 config MAX77620_THERMAL
 	tristate "Temperature sensor driver for Maxim MAX77620 PMIC"
 	depends on MFD_MAX77620
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index baeb70b..f2608f0 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -41,6 +41,7 @@ obj-$(CONFIG_DB8500_THERMAL)	+= db8500_thermal.o
 obj-$(CONFIG_ARMADA_THERMAL)	+= armada_thermal.o
 obj-$(CONFIG_TANGO_THERMAL)	+= tango_thermal.o
 obj-$(CONFIG_IMX_THERMAL)	+= imx_thermal.o
+obj-$(CONFIG_IMX8MM_THERMAL)	+= imx8mm_thermal.o
 obj-$(CONFIG_MAX77620_THERMAL)	+= max77620_thermal.o
 obj-$(CONFIG_QORIQ_THERMAL)	+= qoriq_thermal.o
 obj-$(CONFIG_DA9062_THERMAL)	+= da9062-thermal.o
diff --git a/drivers/thermal/imx8mm_thermal.c b/drivers/thermal/imx8mm_thermal.c
new file mode 100644
index 0000000..04f8a8f
--- /dev/null
+++ b/drivers/thermal/imx8mm_thermal.c
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 NXP.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/thermal.h>
+
+#include "thermal_core.h"
+
+#define TER			0x0	/* TMU enable */
+#define TRITSR			0x20	/* TMU immediate temp */
+
+#define TER_EN			BIT(31)
+#define TRITSR_VAL_MASK		0xff
+
+#define TEMP_LOW_LIMIT		10
+
+struct imx8mm_tmu {
+	struct thermal_zone_device *tzd;
+	void __iomem *base;
+	struct clk *clk;
+};
+
+static int tmu_get_temp(void *data, int *temp)
+{
+	struct imx8mm_tmu *tmu = data;
+	u32 val;
+
+	/* the temp sensor need about 1ms to finish the measurement */
+	usleep_range(1000, 2000);
+
+	val = readl_relaxed(tmu->base + TRITSR) & TRITSR_VAL_MASK;
+	if (val < TEMP_LOW_LIMIT)
+		return -EAGAIN;
+
+	*temp = val * 1000;
+
+	return 0;
+}
+
+static struct thermal_zone_of_device_ops tmu_tz_ops = {
+	.get_temp = tmu_get_temp,
+};
+
+static int imx8mm_tmu_probe(struct platform_device *pdev)
+{
+	struct imx8mm_tmu *tmu;
+	u32 val;
+	int ret;
+
+	tmu = devm_kzalloc(&pdev->dev, sizeof(struct imx8mm_tmu), GFP_KERNEL);
+	if (!tmu)
+		return -ENOMEM;
+
+	tmu->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(tmu->base))
+		return PTR_ERR(tmu->base);
+
+	tmu->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(tmu->clk)) {
+		ret = PTR_ERR(tmu->clk);
+		if (ret != -EPROBE_DEFER)
+			dev_err(&pdev->dev,
+				"failed to get tmu clock: %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(tmu->clk);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to enable tmu clock: %d\n", ret);
+		return ret;
+	}
+
+	tmu->tzd = devm_thermal_zone_of_sensor_register(&pdev->dev, 0,
+							tmu, &tmu_tz_ops);
+	if (IS_ERR(tmu->tzd)) {
+		dev_err(&pdev->dev,
+			"failed to register thermal zone sensor: %d\n", ret);
+		return PTR_ERR(tmu->tzd);
+	}
+
+	platform_set_drvdata(pdev, tmu);
+
+	/* enable the monitor */
+	val = readl_relaxed(tmu->base + TER);
+	val |= TER_EN;
+	writel_relaxed(val, tmu->base + TER);
+
+	return 0;
+}
+
+static int imx8mm_tmu_remove(struct platform_device *pdev)
+{
+	struct imx8mm_tmu *tmu = platform_get_drvdata(pdev);
+	u32 val;
+
+	/* disable TMU */
+	val = readl_relaxed(tmu->base + TER);
+	val &= ~TER_EN;
+	writel_relaxed(val, tmu->base + TER);
+
+	clk_disable_unprepare(tmu->clk);
+	platform_set_drvdata(pdev, NULL);
+
+	return 0;
+}
+
+static const struct of_device_id imx8mm_tmu_table[] = {
+	{ .compatible = "fsl,imx8mm-tmu", },
+	{ },
+};
+
+static struct platform_driver imx8mm_tmu = {
+	.driver = {
+		.name	= "i.mx8mm_thermal",
+		.of_match_table = imx8mm_tmu_table,
+	},
+	.probe = imx8mm_tmu_probe,
+	.remove = imx8mm_tmu_remove,
+};
+module_platform_driver(imx8mm_tmu);
+
+MODULE_AUTHOR("Anson Huang <Anson.Huang@nxp.com>");
+MODULE_DESCRIPTION("i.MX8MM Thermal Monitor Unit driver");
+MODULE_LICENSE("GPL v2");
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH RESEND 3/4] arm64: defconfig: Enable CONFIG_IMX8MM_THERMAL as module

[Anson Huang]

Enable CONFIG_IMX8MM_THERMAL as module to support i.MX8MM
thermal driver.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index f191a4f..cde02aa 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -446,6 +446,7 @@ CONFIG_THERMAL_GOV_POWER_ALLOCATOR=y
 CONFIG_CPU_THERMAL=y
 CONFIG_THERMAL_EMULATION=y
 CONFIG_QORIQ_THERMAL=m
+CONFIG_IMX8MM_THERMAL=m
 CONFIG_ROCKCHIP_THERMAL=m
 CONFIG_RCAR_THERMAL=y
 CONFIG_RCAR_GEN3_THERMAL=y
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH RESEND 4/4] arm64: dts: imx8mm: Add thermal zone support

[Anson Huang]

Add thermal zone and tmu node to support i.MX8MM thermal
driver, ONLY cpu thermal zone is supported, and cpu cooling
is also added.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8mm.dtsi | 43 +++++++++++++++++++++++++++++++
 1 file changed, 43 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index 5ff9b6b..ade930f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -68,6 +68,7 @@
 			nvmem-cells = <&cpu_speed_grade>;
 			nvmem-cell-names = "speed_grade";
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_1: cpu@1 {
@@ -80,6 +81,7 @@
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_2: cpu@2 {
@@ -92,6 +94,7 @@
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_3: cpu@3 {
@@ -104,6 +107,7 @@
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_L2: l2-cache0 {
@@ -209,6 +213,38 @@
 		arm,no-tick-in-suspend;
 	};
 
+	thermal-zones {
+		cpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <2000>;
+			thermal-sensors = <&tmu>;
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit0: trip1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert0>;
+					cooling-device =
+						<&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
 	usbphynop1: usbphynop1 {
 		compatible = "usb-nop-xceiv";
 		clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
@@ -368,6 +404,13 @@
 				gpio-ranges = <&iomuxc 0 119 30>;
 			};
 
+			tmu: tmu@30260000 {
+				compatible = "fsl,imx8mm-tmu";
+				reg = <0x30260000 0x10000>;
+				clocks = <&clk IMX8MM_CLK_TMU_ROOT>;
+				#thermal-sensor-cells = <0>;
+			};
+
 			wdog1: watchdog@30280000 {
 				compatible = "fsl,imx8mm-wdt", "fsl,imx21-wdt";
 				reg = <0x30280000 0x10000>;
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH RESEND 2/4] thermal: imx8mm: Add support for i.MX8MM thermal monitoring unit

[Fabio Estevam]

Hi  Anson,

On Mon, Oct 28, 2019 at 3:07 AM Anson Huang <Anson.Huang@nxp.com> wrote:

> +       ret = clk_prepare_enable(tmu->clk);
> +       if (ret) {
> +               dev_err(&pdev->dev, "failed to enable tmu clock: %d\n", ret);
> +               return ret;
> +       }
> +
> +       tmu->tzd = devm_thermal_zone_of_sensor_register(&pdev->dev, 0,
> +                                                       tmu, &tmu_tz_ops);
> +       if (IS_ERR(tmu->tzd)) {
> +               dev_err(&pdev->dev,
> +                       "failed to register thermal zone sensor: %d\n", ret);

You should disable the tmu clock in the error path.

> +               return PTR_ERR(tmu->tzd);

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH RESEND 1/4] dt-bindings: thermal: imx8mm-thermal: Add binding doc for i.MX8MM

[Anson Huang]

Add thermal binding doc for Freescale's i.MX8MM Thermal Monitoring Unit.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/thermal/imx8mm-thermal.txt        | 15 +++++++++++++++
 1 file changed, 15 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/imx8mm-thermal.txt

diff --git a/Documentation/devicetree/bindings/thermal/imx8mm-thermal.txt b/Documentation/devicetree/bindings/thermal/imx8mm-thermal.txt
new file mode 100644
index 0000000..d09ae82
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/imx8mm-thermal.txt
@@ -0,0 +1,15 @@
+* Thermal Monitoring Unit (TMU) on Freescale i.MX8MM SoC
+
+Required properties:
+- compatible : Must be "fsl,imx8mm-tmu".
+- reg : Address range of TMU registers.
+- clocks : TMU's clock source.
+- #thermal-sensor-cells : Should be 0. See ./thermal.txt for a description.
+
+Example:
+tmu: tmu@30260000 {
+	compatible = "fsl,imx8mm-tmu";
+	reg = <0x30260000 0x10000>;
+	clocks = <&clk IMX8MM_CLK_TMU_ROOT>;
+	#thermal-sensor-cells = <0>;
+};
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel