[PATCH v4 0/6] PAXB INTx support with proper model

[PATCH v4 0/6] PAXB INTx support with proper model

[Srinath Mannam]

This patch series adds PCIe legacy interrupt (INTx) support to the iProc
PCIe driver by modeling it with its own IRQ domain. All 4 interrupts INTA,
INTB, INTC, INTD share the same interrupt line connected to the GIC
in the system. This is now modeled by using its own IRQ domain.

Also update all relevant devicetree files to adapt to the new model.

This patch set is based on Linux-5.5-rc1.

Changes from v3:
  - Addressed Andrew Murray's comments
  - Add change to dispose VIRQ when disabling INTx

Changes from v2:
  - Addressed Lorenzo's comments
    - Corrected INTx to PIN mapping.

Changes from v1:
  - Addressed Rob, Lorenzo, Arnd's comments
    - Used child node for interrupt controller.
  - Addressed Andy Shevchenko's comments
    - Replaced while loop with do-while.

Ray Jui (6):
  dt-bindings: pci: Update iProc PCI binding for INTx support
  PCI: iproc: Add INTx support with better modeling
  arm: dts: Change PCIe INTx mapping for Cygnus
  arm: dts: Change PCIe INTx mapping for NSP
  arm: dts: Change PCIe INTx mapping for HR2
  arm64: dts: Change PCIe INTx mapping for NS2

 .../devicetree/bindings/pci/brcm,iproc-pcie.txt    |  48 +++++++--
 arch/arm/boot/dts/bcm-cygnus.dtsi                  |  30 +++++-
 arch/arm/boot/dts/bcm-hr2.dtsi                     |  30 +++++-
 arch/arm/boot/dts/bcm-nsp.dtsi                     |  45 +++++++--
 arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi   |  28 +++++-
 drivers/pci/controller/pcie-iproc.c                | 108 ++++++++++++++++++++-
 drivers/pci/controller/pcie-iproc.h                |   6 ++
 7 files changed, 268 insertions(+), 27 deletions(-)

-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 1/6] dt-bindings: pci: Update iProc PCI binding for INTx support

[Srinath Mannam]

From: Ray Jui <ray.jui@broadcom.com>

Update the iProc PCIe binding document for better modeling of the legacy
interrupt (INTx) support

Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/pci/brcm,iproc-pcie.txt    | 48 ++++++++++++++++++----
 1 file changed, 41 insertions(+), 7 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
index df065aa..d3f833a 100644
--- a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
@@ -13,9 +13,6 @@ controller, used in Stingray
   PAXB-based root complex is used for external endpoint devices. PAXC-based
 root complex is connected to emulated endpoint devices internal to the ASIC
 - reg: base address and length of the PCIe controller I/O register space
-- #interrupt-cells: set to <1>
-- interrupt-map-mask and interrupt-map, standard PCI properties to define the
-  mapping of the PCIe interface to interrupt numbers
 - linux,pci-domain: PCI domain ID. Should be unique for each host controller
 - bus-range: PCI bus numbers covered
 - #address-cells: set to <3>
@@ -41,6 +38,21 @@ Required:
 - brcm,pcie-ob-axi-offset: The offset from the AXI address to the internal
 address used by the iProc PCIe core (not the PCIe address)
 
+Legacy interrupt (INTx) support (optional):
+
+Note INTx is for PAXB only.
+- interrupt-map-mask and interrupt-map, standard PCI properties to define
+the mapping of the PCIe interface to interrupt numbers
+
+In addition, a sub-node that describes the legacy interrupt controller built
+into the PCIe controller.
+This sub-node must have the following properties:
+ - compatible: must be "brcm,iproc-intc"
+ - interrupt-controller: claims itself as an interrupt controller for INTx
+ - #interrupt-cells: set to <1>
+ - interrupts: interrupt line wired to the generic GIC for INTx support
+ - interrupt-parent: Phandle to the parent interrupt controller
+
 MSI support (optional):
 
 For older platforms without MSI integrated in the GIC, iProc PCIe core provides
@@ -77,8 +89,11 @@ Example:
 		reg = <0x18012000 0x1000>;
 
 		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+				<0 0 0 2 &pcie0_intc 1>,
+				<0 0 0 3 &pcie0_intc 2>,
+				<0 0 0 4 &pcie0_intc 3>;
 
 		linux,pci-domain = <0>;
 
@@ -98,6 +113,14 @@ Example:
 
 		msi-parent = <&msi0>;
 
+		pcie0_intc: interrupt-controller {
+			compatible = "brcm,iproc-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_NONE>;
+		};
+
 		/* iProc event queue based MSI */
 		msi0: msi@18012000 {
 			compatible = "brcm,iproc-msi";
@@ -115,8 +138,11 @@ Example:
 		reg = <0x18013000 0x1000>;
 
 		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+				<0 0 0 2 &pcie1_intc 1>,
+				<0 0 0 3 &pcie1_intc 2>,
+				<0 0 0 4 &pcie1_intc 3>;
 
 		linux,pci-domain = <1>;
 
@@ -130,4 +156,12 @@ Example:
 
 		phys = <&phy 1 6>;
 		phy-names = "pcie-phy";
+
+		pcie1_intc: interrupt-controller {
+			compatible = "brcm,iproc-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_NONE>;
+		};
 	};
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 2/6] PCI: iproc: Add INTx support with better modeling

[Srinath Mannam]

From: Ray Jui <ray.jui@broadcom.com>

Add PCIe legacy interrupt INTx support to the iProc PCIe driver by
modeling it with its own IRQ domain. All 4 interrupts INTA, INTB, INTC,
INTD share the same interrupt line connected to the GIC in the system,
while the status of each INTx can be obtained through the INTX CSR
register

Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
---
 drivers/pci/controller/pcie-iproc.c | 108 +++++++++++++++++++++++++++++++++++-
 drivers/pci/controller/pcie-iproc.h |   6 ++
 2 files changed, 112 insertions(+), 2 deletions(-)

diff --git a/drivers/pci/controller/pcie-iproc.c b/drivers/pci/controller/pcie-iproc.c
index 0a468c7..485967b 100644
--- a/drivers/pci/controller/pcie-iproc.c
+++ b/drivers/pci/controller/pcie-iproc.c
@@ -14,6 +14,7 @@
 #include <linux/delay.h>
 #include <linux/interrupt.h>
 #include <linux/irqchip/arm-gic-v3.h>
+#include <linux/irqchip/chained_irq.h>
 #include <linux/platform_device.h>
 #include <linux/of_address.h>
 #include <linux/of_pci.h>
@@ -270,6 +271,7 @@ enum iproc_pcie_reg {
 
 	/* enable INTx */
 	IPROC_PCIE_INTX_EN,
+	IPROC_PCIE_INTX_CSR,
 
 	/* outbound address mapping */
 	IPROC_PCIE_OARR0,
@@ -314,6 +316,7 @@ static const u16 iproc_pcie_reg_paxb_bcma[] = {
 	[IPROC_PCIE_CFG_ADDR]		= 0x1f8,
 	[IPROC_PCIE_CFG_DATA]		= 0x1fc,
 	[IPROC_PCIE_INTX_EN]		= 0x330,
+	[IPROC_PCIE_INTX_CSR]		= 0x334,
 	[IPROC_PCIE_LINK_STATUS]	= 0xf0c,
 };
 
@@ -325,6 +328,7 @@ static const u16 iproc_pcie_reg_paxb[] = {
 	[IPROC_PCIE_CFG_ADDR]		= 0x1f8,
 	[IPROC_PCIE_CFG_DATA]		= 0x1fc,
 	[IPROC_PCIE_INTX_EN]		= 0x330,
+	[IPROC_PCIE_INTX_CSR]		= 0x334,
 	[IPROC_PCIE_OARR0]		= 0xd20,
 	[IPROC_PCIE_OMAP0]		= 0xd40,
 	[IPROC_PCIE_OARR1]		= 0xd28,
@@ -341,6 +345,7 @@ static const u16 iproc_pcie_reg_paxb_v2[] = {
 	[IPROC_PCIE_CFG_ADDR]		= 0x1f8,
 	[IPROC_PCIE_CFG_DATA]		= 0x1fc,
 	[IPROC_PCIE_INTX_EN]		= 0x330,
+	[IPROC_PCIE_INTX_CSR]		= 0x334,
 	[IPROC_PCIE_OARR0]		= 0xd20,
 	[IPROC_PCIE_OMAP0]		= 0xd40,
 	[IPROC_PCIE_OARR1]		= 0xd28,
@@ -846,9 +851,103 @@ static int iproc_pcie_check_link(struct iproc_pcie *pcie)
 	return link_is_active ? 0 : -ENODEV;
 }
 
-static void iproc_pcie_enable(struct iproc_pcie *pcie)
+static int iproc_pcie_intx_map(struct irq_domain *domain, unsigned int irq,
+			       irq_hw_number_t hwirq)
 {
+	irq_set_chip_and_handler(irq, &dummy_irq_chip, handle_simple_irq);
+	irq_set_chip_data(irq, domain->host_data);
+
+	return 0;
+}
+
+static const struct irq_domain_ops intx_domain_ops = {
+	.map = iproc_pcie_intx_map,
+};
+
+static void iproc_pcie_isr(struct irq_desc *desc)
+{
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+	struct iproc_pcie *pcie;
+	struct device *dev;
+	unsigned long status;
+	u32 bit, virq;
+
+	chained_irq_enter(chip, desc);
+	pcie = irq_desc_get_handler_data(desc);
+	dev = pcie->dev;
+
+	/* go through INTx A, B, C, D until all interrupts are handled */
+	do {
+		status = iproc_pcie_read_reg(pcie, IPROC_PCIE_INTX_CSR);
+		for_each_set_bit(bit, &status, PCI_NUM_INTX) {
+			virq = irq_find_mapping(pcie->irq_domain, bit);
+			if (virq)
+				generic_handle_irq(virq);
+			else
+				dev_err(dev, "unexpected INTx%u\n", bit);
+		}
+	} while ((status & SYS_RC_INTX_MASK) != 0);
+
+	chained_irq_exit(chip, desc);
+}
+
+static int iproc_pcie_intx_enable(struct iproc_pcie *pcie)
+{
+	struct device *dev = pcie->dev;
+	struct device_node *node;
+	int ret;
+
+	/*
+	 * BCMA devices do not map INTx the same way as platform devices. All
+	 * BCMA needs below line to enable INTx
+	 */
 	iproc_pcie_write_reg(pcie, IPROC_PCIE_INTX_EN, SYS_RC_INTX_MASK);
+
+	node = of_get_compatible_child(dev->of_node, "brcm,iproc-intc");
+	if (node)
+		pcie->irq = of_irq_get(node, 0);
+
+	if (!node || pcie->irq <= 0)
+		return 0;
+
+	/* set IRQ handler */
+	irq_set_chained_handler_and_data(pcie->irq, iproc_pcie_isr, pcie);
+
+	/* add IRQ domain for INTx */
+	pcie->irq_domain = irq_domain_add_linear(node, PCI_NUM_INTX,
+						 &intx_domain_ops, pcie);
+	if (!pcie->irq_domain) {
+		dev_err(dev, "failed to add INTx IRQ domain\n");
+		ret = -ENOMEM;
+		goto err_rm_handler_data;
+	}
+
+	return 0;
+
+err_rm_handler_data:
+	of_node_put(node);
+	irq_set_chained_handler_and_data(pcie->irq, NULL, NULL);
+
+	return ret;
+}
+
+static void iproc_pcie_intx_disable(struct iproc_pcie *pcie)
+{
+	uint32_t offset, virq;
+
+	iproc_pcie_write_reg(pcie, IPROC_PCIE_INTX_EN, 0x0);
+
+	if (pcie->irq <= 0)
+		return;
+
+	for (offset = 0; offset < PCI_NUM_INTX; offset++) {
+		virq = irq_find_mapping(pcie->irq_domain, offset);
+		if (virq)
+			irq_dispose_mapping(virq);
+	}
+
+	irq_domain_remove(pcie->irq_domain);
+	irq_set_chained_handler_and_data(pcie->irq, NULL, NULL);
 }
 
 static inline bool iproc_pcie_ob_is_valid(struct iproc_pcie *pcie,
@@ -1518,7 +1617,11 @@ int iproc_pcie_setup(struct iproc_pcie *pcie, struct list_head *res)
 		goto err_power_off_phy;
 	}
 
-	iproc_pcie_enable(pcie);
+	ret = iproc_pcie_intx_enable(pcie);
+	if (ret) {
+		dev_err(dev, "failed to enable INTx\n");
+		goto err_power_off_phy;
+	}
 
 	if (IS_ENABLED(CONFIG_PCI_MSI))
 		if (iproc_pcie_msi_enable(pcie))
@@ -1562,6 +1665,7 @@ int iproc_pcie_remove(struct iproc_pcie *pcie)
 	pci_remove_root_bus(pcie->root_bus);
 
 	iproc_pcie_msi_disable(pcie);
+	iproc_pcie_intx_disable(pcie);
 
 	phy_power_off(pcie->phy);
 	phy_exit(pcie->phy);
diff --git a/drivers/pci/controller/pcie-iproc.h b/drivers/pci/controller/pcie-iproc.h
index 4f03ea5..103e568 100644
--- a/drivers/pci/controller/pcie-iproc.h
+++ b/drivers/pci/controller/pcie-iproc.h
@@ -74,6 +74,9 @@ struct iproc_msi;
  * @ib: inbound mapping related parameters
  * @ib_map: outbound mapping region related parameters
  *
+ * @irq: interrupt line wired to the generic GIC for INTx
+ * @irq_domain: IRQ domain for INTx
+ *
  * @need_msi_steer: indicates additional configuration of the iProc PCIe
  * controller is required to steer MSI writes to external interrupt controller
  * @msi: MSI data
@@ -102,6 +105,9 @@ struct iproc_pcie {
 	struct iproc_pcie_ib ib;
 	const struct iproc_pcie_ib_map *ib_map;
 
+	int irq;
+	struct irq_domain *irq_domain;
+
 	bool need_msi_steer;
 	struct iproc_msi *msi;
 };
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v4 2/6] PCI: iproc: Add INTx support with better modeling

[Andrew Murray]

On Fri, Dec 20, 2019 at 09:24:14AM +0530, Srinath Mannam wrote:
> From: Ray Jui <ray.jui@broadcom.com>
> 
> Add PCIe legacy interrupt INTx support to the iProc PCIe driver by
> modeling it with its own IRQ domain. All 4 interrupts INTA, INTB, INTC,
> INTD share the same interrupt line connected to the GIC in the system,
> while the status of each INTx can be obtained through the INTX CSR
> register
> 
> Signed-off-by: Ray Jui <ray.jui@broadcom.com>
> Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>

Reviewed-by: Andrew Murray <andrew.murray@arm.com>

> ---
>  drivers/pci/controller/pcie-iproc.c | 108 +++++++++++++++++++++++++++++++++++-
>  drivers/pci/controller/pcie-iproc.h |   6 ++
>  2 files changed, 112 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/pci/controller/pcie-iproc.c b/drivers/pci/controller/pcie-iproc.c
> index 0a468c7..485967b 100644
> --- a/drivers/pci/controller/pcie-iproc.c
> +++ b/drivers/pci/controller/pcie-iproc.c
> @@ -14,6 +14,7 @@
>  #include <linux/delay.h>
>  #include <linux/interrupt.h>
>  #include <linux/irqchip/arm-gic-v3.h>
> +#include <linux/irqchip/chained_irq.h>
>  #include <linux/platform_device.h>
>  #include <linux/of_address.h>
>  #include <linux/of_pci.h>
> @@ -270,6 +271,7 @@ enum iproc_pcie_reg {
>  
>  	/* enable INTx */
>  	IPROC_PCIE_INTX_EN,
> +	IPROC_PCIE_INTX_CSR,
>  
>  	/* outbound address mapping */
>  	IPROC_PCIE_OARR0,
> @@ -314,6 +316,7 @@ static const u16 iproc_pcie_reg_paxb_bcma[] = {
>  	[IPROC_PCIE_CFG_ADDR]		= 0x1f8,
>  	[IPROC_PCIE_CFG_DATA]		= 0x1fc,
>  	[IPROC_PCIE_INTX_EN]		= 0x330,
> +	[IPROC_PCIE_INTX_CSR]		= 0x334,
>  	[IPROC_PCIE_LINK_STATUS]	= 0xf0c,
>  };
>  
> @@ -325,6 +328,7 @@ static const u16 iproc_pcie_reg_paxb[] = {
>  	[IPROC_PCIE_CFG_ADDR]		= 0x1f8,
>  	[IPROC_PCIE_CFG_DATA]		= 0x1fc,
>  	[IPROC_PCIE_INTX_EN]		= 0x330,
> +	[IPROC_PCIE_INTX_CSR]		= 0x334,
>  	[IPROC_PCIE_OARR0]		= 0xd20,
>  	[IPROC_PCIE_OMAP0]		= 0xd40,
>  	[IPROC_PCIE_OARR1]		= 0xd28,
> @@ -341,6 +345,7 @@ static const u16 iproc_pcie_reg_paxb_v2[] = {
>  	[IPROC_PCIE_CFG_ADDR]		= 0x1f8,
>  	[IPROC_PCIE_CFG_DATA]		= 0x1fc,
>  	[IPROC_PCIE_INTX_EN]		= 0x330,
> +	[IPROC_PCIE_INTX_CSR]		= 0x334,
>  	[IPROC_PCIE_OARR0]		= 0xd20,
>  	[IPROC_PCIE_OMAP0]		= 0xd40,
>  	[IPROC_PCIE_OARR1]		= 0xd28,
> @@ -846,9 +851,103 @@ static int iproc_pcie_check_link(struct iproc_pcie *pcie)
>  	return link_is_active ? 0 : -ENODEV;
>  }
>  
> -static void iproc_pcie_enable(struct iproc_pcie *pcie)
> +static int iproc_pcie_intx_map(struct irq_domain *domain, unsigned int irq,
> +			       irq_hw_number_t hwirq)
>  {
> +	irq_set_chip_and_handler(irq, &dummy_irq_chip, handle_simple_irq);
> +	irq_set_chip_data(irq, domain->host_data);
> +
> +	return 0;
> +}
> +
> +static const struct irq_domain_ops intx_domain_ops = {
> +	.map = iproc_pcie_intx_map,
> +};
> +
> +static void iproc_pcie_isr(struct irq_desc *desc)
> +{
> +	struct irq_chip *chip = irq_desc_get_chip(desc);
> +	struct iproc_pcie *pcie;
> +	struct device *dev;
> +	unsigned long status;
> +	u32 bit, virq;
> +
> +	chained_irq_enter(chip, desc);
> +	pcie = irq_desc_get_handler_data(desc);
> +	dev = pcie->dev;
> +
> +	/* go through INTx A, B, C, D until all interrupts are handled */
> +	do {
> +		status = iproc_pcie_read_reg(pcie, IPROC_PCIE_INTX_CSR);
> +		for_each_set_bit(bit, &status, PCI_NUM_INTX) {
> +			virq = irq_find_mapping(pcie->irq_domain, bit);
> +			if (virq)
> +				generic_handle_irq(virq);
> +			else
> +				dev_err(dev, "unexpected INTx%u\n", bit);
> +		}
> +	} while ((status & SYS_RC_INTX_MASK) != 0);
> +
> +	chained_irq_exit(chip, desc);
> +}
> +
> +static int iproc_pcie_intx_enable(struct iproc_pcie *pcie)
> +{
> +	struct device *dev = pcie->dev;
> +	struct device_node *node;
> +	int ret;
> +
> +	/*
> +	 * BCMA devices do not map INTx the same way as platform devices. All
> +	 * BCMA needs below line to enable INTx
> +	 */
>  	iproc_pcie_write_reg(pcie, IPROC_PCIE_INTX_EN, SYS_RC_INTX_MASK);
> +
> +	node = of_get_compatible_child(dev->of_node, "brcm,iproc-intc");
> +	if (node)
> +		pcie->irq = of_irq_get(node, 0);
> +
> +	if (!node || pcie->irq <= 0)
> +		return 0;
> +
> +	/* set IRQ handler */
> +	irq_set_chained_handler_and_data(pcie->irq, iproc_pcie_isr, pcie);
> +
> +	/* add IRQ domain for INTx */
> +	pcie->irq_domain = irq_domain_add_linear(node, PCI_NUM_INTX,
> +						 &intx_domain_ops, pcie);
> +	if (!pcie->irq_domain) {
> +		dev_err(dev, "failed to add INTx IRQ domain\n");
> +		ret = -ENOMEM;
> +		goto err_rm_handler_data;
> +	}
> +
> +	return 0;
> +
> +err_rm_handler_data:
> +	of_node_put(node);
> +	irq_set_chained_handler_and_data(pcie->irq, NULL, NULL);
> +
> +	return ret;
> +}
> +
> +static void iproc_pcie_intx_disable(struct iproc_pcie *pcie)
> +{
> +	uint32_t offset, virq;
> +
> +	iproc_pcie_write_reg(pcie, IPROC_PCIE_INTX_EN, 0x0);
> +
> +	if (pcie->irq <= 0)
> +		return;
> +
> +	for (offset = 0; offset < PCI_NUM_INTX; offset++) {
> +		virq = irq_find_mapping(pcie->irq_domain, offset);
> +		if (virq)
> +			irq_dispose_mapping(virq);
> +	}
> +
> +	irq_domain_remove(pcie->irq_domain);
> +	irq_set_chained_handler_and_data(pcie->irq, NULL, NULL);
>  }
>  
>  static inline bool iproc_pcie_ob_is_valid(struct iproc_pcie *pcie,
> @@ -1518,7 +1617,11 @@ int iproc_pcie_setup(struct iproc_pcie *pcie, struct list_head *res)
>  		goto err_power_off_phy;
>  	}
>  
> -	iproc_pcie_enable(pcie);
> +	ret = iproc_pcie_intx_enable(pcie);
> +	if (ret) {
> +		dev_err(dev, "failed to enable INTx\n");
> +		goto err_power_off_phy;
> +	}
>  
>  	if (IS_ENABLED(CONFIG_PCI_MSI))
>  		if (iproc_pcie_msi_enable(pcie))
> @@ -1562,6 +1665,7 @@ int iproc_pcie_remove(struct iproc_pcie *pcie)
>  	pci_remove_root_bus(pcie->root_bus);
>  
>  	iproc_pcie_msi_disable(pcie);
> +	iproc_pcie_intx_disable(pcie);
>  
>  	phy_power_off(pcie->phy);
>  	phy_exit(pcie->phy);
> diff --git a/drivers/pci/controller/pcie-iproc.h b/drivers/pci/controller/pcie-iproc.h
> index 4f03ea5..103e568 100644
> --- a/drivers/pci/controller/pcie-iproc.h
> +++ b/drivers/pci/controller/pcie-iproc.h
> @@ -74,6 +74,9 @@ struct iproc_msi;
>   * @ib: inbound mapping related parameters
>   * @ib_map: outbound mapping region related parameters
>   *
> + * @irq: interrupt line wired to the generic GIC for INTx
> + * @irq_domain: IRQ domain for INTx
> + *
>   * @need_msi_steer: indicates additional configuration of the iProc PCIe
>   * controller is required to steer MSI writes to external interrupt controller
>   * @msi: MSI data
> @@ -102,6 +105,9 @@ struct iproc_pcie {
>  	struct iproc_pcie_ib ib;
>  	const struct iproc_pcie_ib_map *ib_map;
>  
> +	int irq;
> +	struct irq_domain *irq_domain;
> +
>  	bool need_msi_steer;
>  	struct iproc_msi *msi;
>  };
> -- 
> 2.7.4
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v4 2/6] PCI: iproc: Add INTx support with better modeling

[Lorenzo Pieralisi]

[+Marc thanks to whom I can review this code with the required IRQ chip
knowledge]

On Fri, Dec 20, 2019 at 09:24:14AM +0530, Srinath Mannam wrote:
> From: Ray Jui <ray.jui@broadcom.com>
> 
> Add PCIe legacy interrupt INTx support to the iProc PCIe driver by
> modeling it with its own IRQ domain. All 4 interrupts INTA, INTB, INTC,
> INTD share the same interrupt line connected to the GIC in the system,
> while the status of each INTx can be obtained through the INTX CSR
> register
          ^
Missing a period.

> Signed-off-by: Ray Jui <ray.jui@broadcom.com>
> Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
> ---
>  drivers/pci/controller/pcie-iproc.c | 108 +++++++++++++++++++++++++++++++++++-
>  drivers/pci/controller/pcie-iproc.h |   6 ++
>  2 files changed, 112 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/pci/controller/pcie-iproc.c b/drivers/pci/controller/pcie-iproc.c
> index 0a468c7..485967b 100644
> --- a/drivers/pci/controller/pcie-iproc.c
> +++ b/drivers/pci/controller/pcie-iproc.c
> @@ -14,6 +14,7 @@
>  #include <linux/delay.h>
>  #include <linux/interrupt.h>
>  #include <linux/irqchip/arm-gic-v3.h>
> +#include <linux/irqchip/chained_irq.h>
>  #include <linux/platform_device.h>
>  #include <linux/of_address.h>
>  #include <linux/of_pci.h>
> @@ -270,6 +271,7 @@ enum iproc_pcie_reg {
>  
>  	/* enable INTx */
>  	IPROC_PCIE_INTX_EN,
> +	IPROC_PCIE_INTX_CSR,
>  
>  	/* outbound address mapping */
>  	IPROC_PCIE_OARR0,
> @@ -314,6 +316,7 @@ static const u16 iproc_pcie_reg_paxb_bcma[] = {
>  	[IPROC_PCIE_CFG_ADDR]		= 0x1f8,
>  	[IPROC_PCIE_CFG_DATA]		= 0x1fc,
>  	[IPROC_PCIE_INTX_EN]		= 0x330,
> +	[IPROC_PCIE_INTX_CSR]		= 0x334,
>  	[IPROC_PCIE_LINK_STATUS]	= 0xf0c,
>  };
>  
> @@ -325,6 +328,7 @@ static const u16 iproc_pcie_reg_paxb[] = {
>  	[IPROC_PCIE_CFG_ADDR]		= 0x1f8,
>  	[IPROC_PCIE_CFG_DATA]		= 0x1fc,
>  	[IPROC_PCIE_INTX_EN]		= 0x330,
> +	[IPROC_PCIE_INTX_CSR]		= 0x334,
>  	[IPROC_PCIE_OARR0]		= 0xd20,
>  	[IPROC_PCIE_OMAP0]		= 0xd40,
>  	[IPROC_PCIE_OARR1]		= 0xd28,
> @@ -341,6 +345,7 @@ static const u16 iproc_pcie_reg_paxb_v2[] = {
>  	[IPROC_PCIE_CFG_ADDR]		= 0x1f8,
>  	[IPROC_PCIE_CFG_DATA]		= 0x1fc,
>  	[IPROC_PCIE_INTX_EN]		= 0x330,
> +	[IPROC_PCIE_INTX_CSR]		= 0x334,
>  	[IPROC_PCIE_OARR0]		= 0xd20,
>  	[IPROC_PCIE_OMAP0]		= 0xd40,
>  	[IPROC_PCIE_OARR1]		= 0xd28,
> @@ -846,9 +851,103 @@ static int iproc_pcie_check_link(struct iproc_pcie *pcie)
>  	return link_is_active ? 0 : -ENODEV;
>  }
>  
> -static void iproc_pcie_enable(struct iproc_pcie *pcie)
> +static int iproc_pcie_intx_map(struct irq_domain *domain, unsigned int irq,
> +			       irq_hw_number_t hwirq)
>  {
> +	irq_set_chip_and_handler(irq, &dummy_irq_chip, handle_simple_irq);

This looks wrong.

Don't tell me there are other PCI controllers drivers implementing this
code so you copied and pasted it; I know that and they are all wrong.

Legacy PCI IRQs are level IRQs so they must be masked/unmasked upon IRQ
entry/exit.

Therefore the IRQ chip representing your controller can't be a
dummy_irq_chip, that has no methods so no masking is implemented
through it and the flow handler must be handle_level_irq (which,
in turn takes care of masking the IRQ - handle_simple_irq does
not).

The IRQ chip in the PCI host bridge has to have a way to mask/unmask
specific IRQs, implement a proper IRQ chip for it please.

We are curious: Have you ever tested this change with a PCI driver
requesting a threaded IRQ ?

Thanks,
Lorenzo

> +	irq_set_chip_data(irq, domain->host_data);
> +
> +	return 0;
> +}
> +
> +static const struct irq_domain_ops intx_domain_ops = {
> +	.map = iproc_pcie_intx_map,
> +};
> +
> +static void iproc_pcie_isr(struct irq_desc *desc)
> +{
> +	struct irq_chip *chip = irq_desc_get_chip(desc);
> +	struct iproc_pcie *pcie;
> +	struct device *dev;
> +	unsigned long status;
> +	u32 bit, virq;
> +
> +	chained_irq_enter(chip, desc);
> +	pcie = irq_desc_get_handler_data(desc);
> +	dev = pcie->dev;
> +
> +	/* go through INTx A, B, C, D until all interrupts are handled */
> +	do {
> +		status = iproc_pcie_read_reg(pcie, IPROC_PCIE_INTX_CSR);
> +		for_each_set_bit(bit, &status, PCI_NUM_INTX) {
> +			virq = irq_find_mapping(pcie->irq_domain, bit);
> +			if (virq)
> +				generic_handle_irq(virq);
> +			else
> +				dev_err(dev, "unexpected INTx%u\n", bit);
> +		}
> +	} while ((status & SYS_RC_INTX_MASK) != 0);
> +
> +	chained_irq_exit(chip, desc);
> +}
> +
> +static int iproc_pcie_intx_enable(struct iproc_pcie *pcie)
> +{
> +	struct device *dev = pcie->dev;
> +	struct device_node *node;
> +	int ret;
> +
> +	/*
> +	 * BCMA devices do not map INTx the same way as platform devices. All
> +	 * BCMA needs below line to enable INTx
> +	 */
>  	iproc_pcie_write_reg(pcie, IPROC_PCIE_INTX_EN, SYS_RC_INTX_MASK);
> +
> +	node = of_get_compatible_child(dev->of_node, "brcm,iproc-intc");
> +	if (node)
> +		pcie->irq = of_irq_get(node, 0);
> +
> +	if (!node || pcie->irq <= 0)
> +		return 0;
> +
> +	/* set IRQ handler */
> +	irq_set_chained_handler_and_data(pcie->irq, iproc_pcie_isr, pcie);
> +
> +	/* add IRQ domain for INTx */
> +	pcie->irq_domain = irq_domain_add_linear(node, PCI_NUM_INTX,
> +						 &intx_domain_ops, pcie);
> +	if (!pcie->irq_domain) {
> +		dev_err(dev, "failed to add INTx IRQ domain\n");
> +		ret = -ENOMEM;
> +		goto err_rm_handler_data;
> +	}
> +
> +	return 0;
> +
> +err_rm_handler_data:
> +	of_node_put(node);
> +	irq_set_chained_handler_and_data(pcie->irq, NULL, NULL);
> +
> +	return ret;
> +}
> +
> +static void iproc_pcie_intx_disable(struct iproc_pcie *pcie)
> +{
> +	uint32_t offset, virq;
> +
> +	iproc_pcie_write_reg(pcie, IPROC_PCIE_INTX_EN, 0x0);
> +
> +	if (pcie->irq <= 0)
> +		return;
> +
> +	for (offset = 0; offset < PCI_NUM_INTX; offset++) {
> +		virq = irq_find_mapping(pcie->irq_domain, offset);
> +		if (virq)
> +			irq_dispose_mapping(virq);
> +	}
> +
> +	irq_domain_remove(pcie->irq_domain);
> +	irq_set_chained_handler_and_data(pcie->irq, NULL, NULL);
>  }
>  
>  static inline bool iproc_pcie_ob_is_valid(struct iproc_pcie *pcie,
> @@ -1518,7 +1617,11 @@ int iproc_pcie_setup(struct iproc_pcie *pcie, struct list_head *res)
>  		goto err_power_off_phy;
>  	}
>  
> -	iproc_pcie_enable(pcie);
> +	ret = iproc_pcie_intx_enable(pcie);
> +	if (ret) {
> +		dev_err(dev, "failed to enable INTx\n");
> +		goto err_power_off_phy;
> +	}
>  
>  	if (IS_ENABLED(CONFIG_PCI_MSI))
>  		if (iproc_pcie_msi_enable(pcie))
> @@ -1562,6 +1665,7 @@ int iproc_pcie_remove(struct iproc_pcie *pcie)
>  	pci_remove_root_bus(pcie->root_bus);
>  
>  	iproc_pcie_msi_disable(pcie);
> +	iproc_pcie_intx_disable(pcie);
>  
>  	phy_power_off(pcie->phy);
>  	phy_exit(pcie->phy);
> diff --git a/drivers/pci/controller/pcie-iproc.h b/drivers/pci/controller/pcie-iproc.h
> index 4f03ea5..103e568 100644
> --- a/drivers/pci/controller/pcie-iproc.h
> +++ b/drivers/pci/controller/pcie-iproc.h
> @@ -74,6 +74,9 @@ struct iproc_msi;
>   * @ib: inbound mapping related parameters
>   * @ib_map: outbound mapping region related parameters
>   *
> + * @irq: interrupt line wired to the generic GIC for INTx
> + * @irq_domain: IRQ domain for INTx
> + *
>   * @need_msi_steer: indicates additional configuration of the iProc PCIe
>   * controller is required to steer MSI writes to external interrupt controller
>   * @msi: MSI data
> @@ -102,6 +105,9 @@ struct iproc_pcie {
>  	struct iproc_pcie_ib ib;
>  	const struct iproc_pcie_ib_map *ib_map;
>  
> +	int irq;
> +	struct irq_domain *irq_domain;
> +
>  	bool need_msi_steer;
>  	struct iproc_msi *msi;
>  };
> -- 
> 2.7.4
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 3/6] arm: dts: Change PCIe INTx mapping for Cygnus

[Srinath Mannam]

From: Ray Jui <ray.jui@broadcom.com>

Change the PCIe INTx mapping to model the 4 INTx interrupts in the
IRQ domain of the iProc PCIe controller itself

Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
---
 arch/arm/boot/dts/bcm-cygnus.dtsi | 30 ++++++++++++++++++++++++++----
 1 file changed, 26 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
index 2dac3ef..ca23e82 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@@ -264,8 +264,11 @@
 			reg = <0x18012000 0x1000>;
 
 			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+					<0 0 0 2 &pcie0_intc 1>,
+					<0 0 0 3 &pcie0_intc 2>,
+					<0 0 0 4 &pcie0_intc 3>;
 
 			linux,pci-domain = <0>;
 
@@ -292,6 +295,14 @@
 					     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
 			};
+
+			pcie0_intc: interrupt-controller {
+				compatible = "brcm,iproc-intc";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			};
 		};
 
 		pcie1: pcie@18013000 {
@@ -299,8 +310,11 @@
 			reg = <0x18013000 0x1000>;
 
 			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+					<0 0 0 2 &pcie1_intc 1>,
+					<0 0 0 3 &pcie1_intc 2>,
+					<0 0 0 4 &pcie1_intc 3>;
 
 			linux,pci-domain = <1>;
 
@@ -327,6 +341,14 @@
 					     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
 			};
+
+			pcie1_intc: interrupt-controller {
+				compatible = "brcm,iproc-intc";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+			};
 		};
 
 		dma0: dma@18018000 {
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 4/6] arm: dts: Change PCIe INTx mapping for NSP

[Srinath Mannam]

From: Ray Jui <ray.jui@broadcom.com>

Change the PCIe INTx mapping to model the 4 INTx interrupts in the
IRQ domain of the iProc PCIe controller itself

Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
---
 arch/arm/boot/dts/bcm-nsp.dtsi | 45 ++++++++++++++++++++++++++++++++++++------
 1 file changed, 39 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi
index da6d70f..6d73221 100644
--- a/arch/arm/boot/dts/bcm-nsp.dtsi
+++ b/arch/arm/boot/dts/bcm-nsp.dtsi
@@ -529,8 +529,11 @@
 		reg = <0x18012000 0x1000>;
 
 		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+				<0 0 0 2 &pcie0_intc 1>,
+				<0 0 0 3 &pcie0_intc 2>,
+				<0 0 0 4 &pcie0_intc 3>;
 
 		linux,pci-domain = <0>;
 
@@ -559,6 +562,14 @@
 				     <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
+
+		pcie0_intc: interrupt-controller {
+			compatible = "brcm,iproc-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+		};
 	};
 
 	pcie1: pcie@18013000 {
@@ -566,8 +577,11 @@
 		reg = <0x18013000 0x1000>;
 
 		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+				<0 0 0 2 &pcie1_intc 1>,
+				<0 0 0 3 &pcie1_intc 2>,
+				<0 0 0 4 &pcie1_intc 3>;
 
 		linux,pci-domain = <1>;
 
@@ -596,6 +610,14 @@
 				     <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
+
+		pcie1_intc: interrupt-controller {
+			compatible = "brcm,iproc-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+		};
 	};
 
 	pcie2: pcie@18014000 {
@@ -603,8 +625,11 @@
 		reg = <0x18014000 0x1000>;
 
 		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+				<0 0 0 2 &pcie2_intc 1>,
+				<0 0 0 3 &pcie2_intc 2>,
+				<0 0 0 4 &pcie2_intc 3>;
 
 		linux,pci-domain = <2>;
 
@@ -633,6 +658,14 @@
 				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
+
+		pcie2_intc: interrupt-controller {
+			compatible = "brcm,iproc-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+		};
 	};
 
 	thermal-zones {
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 5/6] arm: dts: Change PCIe INTx mapping for HR2

[Srinath Mannam]

From: Ray Jui <ray.jui@broadcom.com>

Change the PCIe INTx mapping to model the 4 INTx interrupts in the
IRQ domain of the iProc PCIe controller itself

Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
---
 arch/arm/boot/dts/bcm-hr2.dtsi | 30 ++++++++++++++++++++++++++----
 1 file changed, 26 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/bcm-hr2.dtsi b/arch/arm/boot/dts/bcm-hr2.dtsi
index 6142c67..80c3add 100644
--- a/arch/arm/boot/dts/bcm-hr2.dtsi
+++ b/arch/arm/boot/dts/bcm-hr2.dtsi
@@ -299,8 +299,11 @@
 		reg = <0x18012000 0x1000>;
 
 		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+				<0 0 0 2 &pcie0_intc 1>,
+				<0 0 0 3 &pcie0_intc 2>,
+				<0 0 0 4 &pcie0_intc 3>;
 
 		linux,pci-domain = <0>;
 
@@ -328,6 +331,14 @@
 				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
+
+		pcie0_intc: interrupt-controller {
+			compatible = "brcm,iproc-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
+		};
 	};
 
 	pcie1: pcie@18013000 {
@@ -335,8 +346,11 @@
 		reg = <0x18013000 0x1000>;
 
 		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+				<0 0 0 2 &pcie1_intc 1>,
+				<0 0 0 3 &pcie1_intc 2>,
+				<0 0 0 4 &pcie1_intc 3>;
 
 		linux,pci-domain = <1>;
 
@@ -364,5 +378,13 @@
 				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
+
+		pcie1_intc: interrupt-controller {
+			compatible = "brcm,iproc-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
+		};
 	};
 };
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 6/6] arm64: dts: Change PCIe INTx mapping for NS2

[Srinath Mannam]

From: Ray Jui <ray.jui@broadcom.com>

Change the PCIe INTx mapping to model the 4 INTx interrupts in the
IRQ domain of the iProc PCIe controller itself

Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
---
 arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi | 28 ++++++++++++++++++++----
 1 file changed, 24 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi b/arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi
index 15f7b0e..489bfd5 100644
--- a/arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi
+++ b/arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi
@@ -117,8 +117,11 @@
 		dma-coherent;
 
 		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+				<0 0 0 2 &pcie0_intc 1>,
+				<0 0 0 3 &pcie0_intc 2>,
+				<0 0 0 4 &pcie0_intc 3>;
 
 		linux,pci-domain = <0>;
 
@@ -140,6 +143,13 @@
 		phy-names = "pcie-phy";
 
 		msi-parent = <&v2m0>;
+		pcie0_intc: interrupt-controller {
+			compatible = "brcm,iproc-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>;
+		};
 	};
 
 	pcie4: pcie@50020000 {
@@ -148,8 +158,11 @@
 		dma-coherent;
 
 		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie4_intc 0>,
+				<0 0 0 2 &pcie4_intc 1>,
+				<0 0 0 3 &pcie4_intc 2>,
+				<0 0 0 4 &pcie4_intc 3>;
 
 		linux,pci-domain = <4>;
 
@@ -171,6 +184,13 @@
 		phy-names = "pcie-phy";
 
 		msi-parent = <&v2m0>;
+		pcie4_intc: interrupt-controller {
+			compatible = "brcm,iproc-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
+		};
 	};
 
 	pcie8: pcie@60c00000 {
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v4 0/6] PAXB INTx support with proper model

[Florian Fainelli]

On 12/19/19 7:54 PM, Srinath Mannam wrote:
> This patch series adds PCIe legacy interrupt (INTx) support to the iProc
> PCIe driver by modeling it with its own IRQ domain. All 4 interrupts INTA,
> INTB, INTC, INTD share the same interrupt line connected to the GIC
> in the system. This is now modeled by using its own IRQ domain.
> 
> Also update all relevant devicetree files to adapt to the new model.
> 
> This patch set is based on Linux-5.5-rc1.

Lorenzo are you good with those patches so I can apply the device tree
changes to the 5.6 Broadcom SoC pull request?

> 
> Changes from v3:
>   - Addressed Andrew Murray's comments
>   - Add change to dispose VIRQ when disabling INTx
> 
> Changes from v2:
>   - Addressed Lorenzo's comments
>     - Corrected INTx to PIN mapping.
> 
> Changes from v1:
>   - Addressed Rob, Lorenzo, Arnd's comments
>     - Used child node for interrupt controller.
>   - Addressed Andy Shevchenko's comments
>     - Replaced while loop with do-while.
> 
> Ray Jui (6):
>   dt-bindings: pci: Update iProc PCI binding for INTx support
>   PCI: iproc: Add INTx support with better modeling
>   arm: dts: Change PCIe INTx mapping for Cygnus
>   arm: dts: Change PCIe INTx mapping for NSP
>   arm: dts: Change PCIe INTx mapping for HR2
>   arm64: dts: Change PCIe INTx mapping for NS2
> 
>  .../devicetree/bindings/pci/brcm,iproc-pcie.txt    |  48 +++++++--
>  arch/arm/boot/dts/bcm-cygnus.dtsi                  |  30 +++++-
>  arch/arm/boot/dts/bcm-hr2.dtsi                     |  30 +++++-
>  arch/arm/boot/dts/bcm-nsp.dtsi                     |  45 +++++++--
>  arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi   |  28 +++++-
>  drivers/pci/controller/pcie-iproc.c                | 108 ++++++++++++++++++++-
>  drivers/pci/controller/pcie-iproc.h                |   6 ++
>  7 files changed, 268 insertions(+), 27 deletions(-)
> 


-- 
Florian

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel