* [PATCH 1/6] phy: phy-bcm-ns-usb3: convert to readl_poll_timeout_atomic()
@ 2020-08-25 2:03 Chunfeng Yun
2020-08-25 2:03 ` [PATCH 2/6] phy: phy-bcm-ns2-usbdrd: " Chunfeng Yun
` (5 more replies)
0 siblings, 6 replies; 7+ messages in thread
From: Chunfeng Yun @ 2020-08-25 2:03 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: Bharat Gooty, Rayagonda Kokatanur, linux-arm-msm, linux-kernel,
Rikard Falkeborn, Bjorn Andersson, Chunfeng Yun, Vinod Koul,
Andy Gross, linux-mediatek, Matthias Brugger, linux-arm-kernel
Use readl_poll_timeout_atomic() to simplify code
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
drivers/phy/broadcom/phy-bcm-ns-usb3.c | 22 +++++++++-------------
1 file changed, 9 insertions(+), 13 deletions(-)
diff --git a/drivers/phy/broadcom/phy-bcm-ns-usb3.c b/drivers/phy/broadcom/phy-bcm-ns-usb3.c
index 14f45bc..47b029f 100644
--- a/drivers/phy/broadcom/phy-bcm-ns-usb3.c
+++ b/drivers/phy/broadcom/phy-bcm-ns-usb3.c
@@ -13,6 +13,7 @@
#include <linux/bcma/bcma.h>
#include <linux/delay.h>
#include <linux/err.h>
+#include <linux/iopoll.h>
#include <linux/mdio.h>
#include <linux/module.h>
#include <linux/of_address.h>
@@ -258,29 +259,24 @@ static int bcm_ns_usb3_mdio_probe(struct mdio_device *mdiodev)
**************************************************/
static int bcm_ns_usb3_wait_reg(struct bcm_ns_usb3 *usb3, void __iomem *addr,
- u32 mask, u32 value, unsigned long timeout)
+ u32 mask, u32 value, int usec)
{
- unsigned long deadline = jiffies + timeout;
u32 val;
+ int ret;
- do {
- val = readl(addr);
- if ((val & mask) == value)
- return 0;
- cpu_relax();
- udelay(10);
- } while (!time_after_eq(jiffies, deadline));
+ ret = readl_poll_timeout_atomic(addr, val, ((val & mask) == value),
+ 10, usec);
+ if (ret)
+ dev_err(usb3->dev, "Timeout waiting for register %p\n", addr);
- dev_err(usb3->dev, "Timeout waiting for register %p\n", addr);
-
- return -EBUSY;
+ return ret;
}
static inline int bcm_ns_usb3_mii_mng_wait_idle(struct bcm_ns_usb3 *usb3)
{
return bcm_ns_usb3_wait_reg(usb3, usb3->ccb_mii + BCMA_CCB_MII_MNG_CTL,
0x0100, 0x0000,
- usecs_to_jiffies(BCM_NS_USB3_MII_MNG_TIMEOUT_US));
+ BCM_NS_USB3_MII_MNG_TIMEOUT_US);
}
static int bcm_ns_usb3_platform_phy_write(struct bcm_ns_usb3 *usb3, u16 reg,
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 2/6] phy: phy-bcm-ns2-usbdrd: convert to readl_poll_timeout_atomic()
2020-08-25 2:03 [PATCH 1/6] phy: phy-bcm-ns-usb3: convert to readl_poll_timeout_atomic() Chunfeng Yun
@ 2020-08-25 2:03 ` Chunfeng Yun
2020-08-25 2:03 ` [PATCH 3/6] phy: phy-bcm-sr-usb: " Chunfeng Yun
` (4 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Chunfeng Yun @ 2020-08-25 2:03 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: Bharat Gooty, Rayagonda Kokatanur, linux-arm-msm, linux-kernel,
Rikard Falkeborn, Bjorn Andersson, Chunfeng Yun, Vinod Koul,
Andy Gross, linux-mediatek, Matthias Brugger, linux-arm-kernel
Use readl_poll_timeout_atomic() to simplify code
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
drivers/phy/broadcom/phy-bcm-ns2-usbdrd.c | 13 ++++---------
1 file changed, 4 insertions(+), 9 deletions(-)
diff --git a/drivers/phy/broadcom/phy-bcm-ns2-usbdrd.c b/drivers/phy/broadcom/phy-bcm-ns2-usbdrd.c
index 5276259..9630ac1 100644
--- a/drivers/phy/broadcom/phy-bcm-ns2-usbdrd.c
+++ b/drivers/phy/broadcom/phy-bcm-ns2-usbdrd.c
@@ -18,6 +18,7 @@
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
+#include <linux/iopoll.h>
#include <linux/irq.h>
#include <linux/mfd/syscon.h>
#include <linux/module.h>
@@ -87,17 +88,11 @@ struct ns2_phy_data {
static inline int pll_lock_stat(u32 usb_reg, int reg_mask,
struct ns2_phy_driver *driver)
{
- int retry = PLL_LOCK_RETRY;
u32 val;
- do {
- udelay(1);
- val = readl(driver->icfgdrd_regs + usb_reg);
- if (val & reg_mask)
- return 0;
- } while (--retry > 0);
-
- return -EBUSY;
+ return readl_poll_timeout_atomic(driver->icfgdrd_regs + usb_reg,
+ val, (val & reg_mask), 1,
+ PLL_LOCK_RETRY);
}
static int ns2_drd_phy_init(struct phy *phy)
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 3/6] phy: phy-bcm-sr-usb: convert to readl_poll_timeout_atomic()
2020-08-25 2:03 [PATCH 1/6] phy: phy-bcm-ns-usb3: convert to readl_poll_timeout_atomic() Chunfeng Yun
2020-08-25 2:03 ` [PATCH 2/6] phy: phy-bcm-ns2-usbdrd: " Chunfeng Yun
@ 2020-08-25 2:03 ` Chunfeng Yun
2020-08-25 2:03 ` [PATCH 4/6] phy: phy-qcom-apq8064-sata: convert to readl_relaxed_poll_timeout() Chunfeng Yun
` (3 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Chunfeng Yun @ 2020-08-25 2:03 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: Bharat Gooty, Rayagonda Kokatanur, linux-arm-msm, linux-kernel,
Rikard Falkeborn, Bjorn Andersson, Chunfeng Yun, Vinod Koul,
Andy Gross, linux-mediatek, Matthias Brugger, linux-arm-kernel
Use readl_poll_timeout_atomic() to simplify code
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
drivers/phy/broadcom/phy-bcm-sr-usb.c | 19 ++++++++-----------
1 file changed, 8 insertions(+), 11 deletions(-)
diff --git a/drivers/phy/broadcom/phy-bcm-sr-usb.c b/drivers/phy/broadcom/phy-bcm-sr-usb.c
index 77c025a..c3e99ad 100644
--- a/drivers/phy/broadcom/phy-bcm-sr-usb.c
+++ b/drivers/phy/broadcom/phy-bcm-sr-usb.c
@@ -5,6 +5,7 @@
#include <linux/delay.h>
#include <linux/io.h>
+#include <linux/iopoll.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/phy/phy.h>
@@ -109,19 +110,15 @@ static inline void bcm_usb_reg32_setbits(void __iomem *addr, uint32_t set)
static int bcm_usb_pll_lock_check(void __iomem *addr, u32 bit)
{
- int retry;
- u32 rd_data;
+ u32 data;
+ int ret;
- retry = PLL_LOCK_RETRY_COUNT;
- do {
- rd_data = readl(addr);
- if (rd_data & bit)
- return 0;
- udelay(1);
- } while (--retry > 0);
+ ret = readl_poll_timeout_atomic(addr, data, (data & bit), 1,
+ PLL_LOCK_RETRY_COUNT);
+ if (ret)
+ pr_err("%s: FAIL\n", __func__);
- pr_err("%s: FAIL\n", __func__);
- return -ETIMEDOUT;
+ return ret;
}
static int bcm_usb_ss_phy_init(struct bcm_usb_phy_cfg *phy_cfg)
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 4/6] phy: phy-qcom-apq8064-sata: convert to readl_relaxed_poll_timeout()
2020-08-25 2:03 [PATCH 1/6] phy: phy-bcm-ns-usb3: convert to readl_poll_timeout_atomic() Chunfeng Yun
2020-08-25 2:03 ` [PATCH 2/6] phy: phy-bcm-ns2-usbdrd: " Chunfeng Yun
2020-08-25 2:03 ` [PATCH 3/6] phy: phy-bcm-sr-usb: " Chunfeng Yun
@ 2020-08-25 2:03 ` Chunfeng Yun
2020-08-25 2:03 ` [PATCH 5/6] phy: phy-pxa-28nm-hsic: convert to readl_poll_timeout() Chunfeng Yun
` (2 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Chunfeng Yun @ 2020-08-25 2:03 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: Bharat Gooty, Rayagonda Kokatanur, linux-arm-msm, linux-kernel,
Rikard Falkeborn, Bjorn Andersson, Chunfeng Yun, Vinod Koul,
Andy Gross, linux-mediatek, Matthias Brugger, linux-arm-kernel
Use readl_relaxed_poll_timeout() to simplify code, rename local function
read_poll_timeout() as poll_timeout() to avoid repeated definition
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
drivers/phy/qualcomm/phy-qcom-apq8064-sata.c | 21 ++++++++-------------
1 file changed, 8 insertions(+), 13 deletions(-)
diff --git a/drivers/phy/qualcomm/phy-qcom-apq8064-sata.c b/drivers/phy/qualcomm/phy-qcom-apq8064-sata.c
index febe0ae..ce91ae7 100644
--- a/drivers/phy/qualcomm/phy-qcom-apq8064-sata.c
+++ b/drivers/phy/qualcomm/phy-qcom-apq8064-sata.c
@@ -4,6 +4,7 @@
*/
#include <linux/io.h>
+#include <linux/iopoll.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/of.h>
@@ -72,18 +73,12 @@ struct qcom_apq8064_sata_phy {
};
/* Helper function to do poll and timeout */
-static int read_poll_timeout(void __iomem *addr, u32 mask)
+static int poll_timeout(void __iomem *addr, u32 mask)
{
- unsigned long timeout = jiffies + msecs_to_jiffies(TIMEOUT_MS);
+ u32 val;
- do {
- if (readl_relaxed(addr) & mask)
- return 0;
-
- usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50);
- } while (!time_after(jiffies, timeout));
-
- return (readl_relaxed(addr) & mask) ? 0 : -ETIMEDOUT;
+ return readl_relaxed_poll_timeout(addr, val, (val & mask),
+ DELAY_INTERVAL_US, TIMEOUT_MS * 1000);
}
static int qcom_apq8064_sata_phy_init(struct phy *generic_phy)
@@ -137,21 +132,21 @@ static int qcom_apq8064_sata_phy_init(struct phy *generic_phy)
writel_relaxed(0x05, base + UNIPHY_PLL_LKDET_CFG2);
/* PLL Lock wait */
- ret = read_poll_timeout(base + UNIPHY_PLL_STATUS, UNIPHY_PLL_LOCK);
+ ret = poll_timeout(base + UNIPHY_PLL_STATUS, UNIPHY_PLL_LOCK);
if (ret) {
dev_err(phy->dev, "poll timeout UNIPHY_PLL_STATUS\n");
return ret;
}
/* TX Calibration */
- ret = read_poll_timeout(base + SATA_PHY_TX_IMCAL_STAT, SATA_PHY_TX_CAL);
+ ret = poll_timeout(base + SATA_PHY_TX_IMCAL_STAT, SATA_PHY_TX_CAL);
if (ret) {
dev_err(phy->dev, "poll timeout SATA_PHY_TX_IMCAL_STAT\n");
return ret;
}
/* RX Calibration */
- ret = read_poll_timeout(base + SATA_PHY_RX_IMCAL_STAT, SATA_PHY_RX_CAL);
+ ret = poll_timeout(base + SATA_PHY_RX_IMCAL_STAT, SATA_PHY_RX_CAL);
if (ret) {
dev_err(phy->dev, "poll timeout SATA_PHY_RX_IMCAL_STAT\n");
return ret;
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 5/6] phy: phy-pxa-28nm-hsic: convert to readl_poll_timeout()
2020-08-25 2:03 [PATCH 1/6] phy: phy-bcm-ns-usb3: convert to readl_poll_timeout_atomic() Chunfeng Yun
` (2 preceding siblings ...)
2020-08-25 2:03 ` [PATCH 4/6] phy: phy-qcom-apq8064-sata: convert to readl_relaxed_poll_timeout() Chunfeng Yun
@ 2020-08-25 2:03 ` Chunfeng Yun
2020-08-25 2:03 ` [PATCH 6/6] phy: phy-pxa-28nm-usb2: " Chunfeng Yun
2020-09-08 4:26 ` [PATCH 1/6] phy: phy-bcm-ns-usb3: convert to readl_poll_timeout_atomic() Vinod Koul
5 siblings, 0 replies; 7+ messages in thread
From: Chunfeng Yun @ 2020-08-25 2:03 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: Bharat Gooty, Rayagonda Kokatanur, linux-arm-msm, linux-kernel,
Rikard Falkeborn, Bjorn Andersson, Chunfeng Yun, Vinod Koul,
Andy Gross, linux-mediatek, Matthias Brugger, linux-arm-kernel
Use readl_poll_timeout() to simplify code
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
drivers/phy/marvell/phy-pxa-28nm-hsic.c | 40 ++++++++++++++++-----------------
1 file changed, 20 insertions(+), 20 deletions(-)
diff --git a/drivers/phy/marvell/phy-pxa-28nm-hsic.c b/drivers/phy/marvell/phy-pxa-28nm-hsic.c
index ae8370a..31b43d2 100644
--- a/drivers/phy/marvell/phy-pxa-28nm-hsic.c
+++ b/drivers/phy/marvell/phy-pxa-28nm-hsic.c
@@ -12,6 +12,7 @@
#include <linux/slab.h>
#include <linux/of.h>
#include <linux/io.h>
+#include <linux/iopoll.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/module.h>
@@ -44,15 +45,12 @@ struct mv_hsic_phy {
struct clk *clk;
};
-static bool wait_for_reg(void __iomem *reg, u32 mask, unsigned long timeout)
+static int wait_for_reg(void __iomem *reg, u32 mask, u32 ms)
{
- timeout += jiffies;
- while (time_is_after_eq_jiffies(timeout)) {
- if ((readl(reg) & mask) == mask)
- return true;
- msleep(1);
- }
- return false;
+ u32 val;
+
+ return readl_poll_timeout(reg, val, ((val & mask) == mask),
+ 1000, 1000 * ms);
}
static int mv_hsic_phy_init(struct phy *phy)
@@ -60,6 +58,7 @@ static int mv_hsic_phy_init(struct phy *phy)
struct mv_hsic_phy *mv_phy = phy_get_drvdata(phy);
struct platform_device *pdev = mv_phy->pdev;
void __iomem *base = mv_phy->base;
+ int ret;
clk_prepare_enable(mv_phy->clk);
@@ -75,14 +74,14 @@ static int mv_hsic_phy_init(struct phy *phy)
base + PHY_28NM_HSIC_PLL_CTRL2);
/* Make sure PHY PLL is locked */
- if (!wait_for_reg(base + PHY_28NM_HSIC_PLL_CTRL2,
- PHY_28NM_HSIC_H2S_PLL_LOCK, HZ / 10)) {
+ ret = wait_for_reg(base + PHY_28NM_HSIC_PLL_CTRL2,
+ PHY_28NM_HSIC_H2S_PLL_LOCK, 100);
+ if (ret) {
dev_err(&pdev->dev, "HSIC PHY PLL not locked after 100mS.");
clk_disable_unprepare(mv_phy->clk);
- return -ETIMEDOUT;
}
- return 0;
+ return ret;
}
static int mv_hsic_phy_power_on(struct phy *phy)
@@ -91,6 +90,7 @@ static int mv_hsic_phy_power_on(struct phy *phy)
struct platform_device *pdev = mv_phy->pdev;
void __iomem *base = mv_phy->base;
u32 reg;
+ int ret;
reg = readl(base + PHY_28NM_HSIC_CTRL);
/* Avoid SE0 state when resume for some device will take it as reset */
@@ -108,20 +108,20 @@ static int mv_hsic_phy_power_on(struct phy *phy)
*/
/* Make sure PHY Calibration is ready */
- if (!wait_for_reg(base + PHY_28NM_HSIC_IMPCAL_CAL,
- PHY_28NM_HSIC_H2S_IMPCAL_DONE, HZ / 10)) {
+ ret = wait_for_reg(base + PHY_28NM_HSIC_IMPCAL_CAL,
+ PHY_28NM_HSIC_H2S_IMPCAL_DONE, 100);
+ if (ret) {
dev_warn(&pdev->dev, "HSIC PHY READY not set after 100mS.");
- return -ETIMEDOUT;
+ return ret;
}
/* Waiting for HSIC connect int*/
- if (!wait_for_reg(base + PHY_28NM_HSIC_INT,
- PHY_28NM_HSIC_CONNECT_INT, HZ / 5)) {
+ ret = wait_for_reg(base + PHY_28NM_HSIC_INT,
+ PHY_28NM_HSIC_CONNECT_INT, 200);
+ if (ret)
dev_warn(&pdev->dev, "HSIC wait for connect interrupt timeout.");
- return -ETIMEDOUT;
- }
- return 0;
+ return ret;
}
static int mv_hsic_phy_power_off(struct phy *phy)
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 6/6] phy: phy-pxa-28nm-usb2: convert to readl_poll_timeout()
2020-08-25 2:03 [PATCH 1/6] phy: phy-bcm-ns-usb3: convert to readl_poll_timeout_atomic() Chunfeng Yun
` (3 preceding siblings ...)
2020-08-25 2:03 ` [PATCH 5/6] phy: phy-pxa-28nm-hsic: convert to readl_poll_timeout() Chunfeng Yun
@ 2020-08-25 2:03 ` Chunfeng Yun
2020-09-08 4:26 ` [PATCH 1/6] phy: phy-bcm-ns-usb3: convert to readl_poll_timeout_atomic() Vinod Koul
5 siblings, 0 replies; 7+ messages in thread
From: Chunfeng Yun @ 2020-08-25 2:03 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: Bharat Gooty, Rayagonda Kokatanur, linux-arm-msm, linux-kernel,
Rikard Falkeborn, Bjorn Andersson, Chunfeng Yun, Vinod Koul,
Andy Gross, linux-mediatek, Matthias Brugger, linux-arm-kernel
Use readl_poll_timeout() to simplify code
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
drivers/phy/marvell/phy-pxa-28nm-usb2.c | 33 +++++++++++++++------------------
1 file changed, 15 insertions(+), 18 deletions(-)
diff --git a/drivers/phy/marvell/phy-pxa-28nm-usb2.c b/drivers/phy/marvell/phy-pxa-28nm-usb2.c
index 9fd8817..a175ae9 100644
--- a/drivers/phy/marvell/phy-pxa-28nm-usb2.c
+++ b/drivers/phy/marvell/phy-pxa-28nm-usb2.c
@@ -13,6 +13,7 @@
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/io.h>
+#include <linux/iopoll.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/module.h>
@@ -138,15 +139,12 @@ struct mv_usb2_phy {
struct clk *clk;
};
-static bool wait_for_reg(void __iomem *reg, u32 mask, unsigned long timeout)
+static int wait_for_reg(void __iomem *reg, u32 mask, u32 ms)
{
- timeout += jiffies;
- while (time_is_after_eq_jiffies(timeout)) {
- if ((readl(reg) & mask) == mask)
- return true;
- msleep(1);
- }
- return false;
+ u32 val;
+
+ return readl_poll_timeout(reg, val, ((val & mask) == mask),
+ 1000, 1000 * ms);
}
static int mv_usb2_phy_28nm_init(struct phy *phy)
@@ -208,24 +206,23 @@ static int mv_usb2_phy_28nm_init(struct phy *phy)
*/
/* Make sure PHY Calibration is ready */
- if (!wait_for_reg(base + PHY_28NM_CAL_REG,
- PHY_28NM_PLL_PLLCAL_DONE | PHY_28NM_PLL_IMPCAL_DONE,
- HZ / 10)) {
+ ret = wait_for_reg(base + PHY_28NM_CAL_REG,
+ PHY_28NM_PLL_PLLCAL_DONE | PHY_28NM_PLL_IMPCAL_DONE,
+ 100);
+ if (ret) {
dev_warn(&pdev->dev, "USB PHY PLL calibrate not done after 100mS.");
- ret = -ETIMEDOUT;
goto err_clk;
}
- if (!wait_for_reg(base + PHY_28NM_RX_REG1,
- PHY_28NM_RX_SQCAL_DONE, HZ / 10)) {
+ ret = wait_for_reg(base + PHY_28NM_RX_REG1,
+ PHY_28NM_RX_SQCAL_DONE, 100);
+ if (ret) {
dev_warn(&pdev->dev, "USB PHY RX SQ calibrate not done after 100mS.");
- ret = -ETIMEDOUT;
goto err_clk;
}
/* Make sure PHY PLL is ready */
- if (!wait_for_reg(base + PHY_28NM_PLL_REG0,
- PHY_28NM_PLL_READY, HZ / 10)) {
+ ret = wait_for_reg(base + PHY_28NM_PLL_REG0, PHY_28NM_PLL_READY, 100);
+ if (ret) {
dev_warn(&pdev->dev, "PLL_READY not set after 100mS.");
- ret = -ETIMEDOUT;
goto err_clk;
}
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH 1/6] phy: phy-bcm-ns-usb3: convert to readl_poll_timeout_atomic()
2020-08-25 2:03 [PATCH 1/6] phy: phy-bcm-ns-usb3: convert to readl_poll_timeout_atomic() Chunfeng Yun
` (4 preceding siblings ...)
2020-08-25 2:03 ` [PATCH 6/6] phy: phy-pxa-28nm-usb2: " Chunfeng Yun
@ 2020-09-08 4:26 ` Vinod Koul
5 siblings, 0 replies; 7+ messages in thread
From: Vinod Koul @ 2020-09-08 4:26 UTC (permalink / raw)
To: Chunfeng Yun
Cc: Bharat Gooty, Rayagonda Kokatanur, linux-arm-msm, linux-kernel,
Rikard Falkeborn, Bjorn Andersson, Andy Gross, linux-mediatek,
Matthias Brugger, Kishon Vijay Abraham I, linux-arm-kernel
On 25-08-20, 10:03, Chunfeng Yun wrote:
> Use readl_poll_timeout_atomic() to simplify code
Applied all, thanks
--
~Vinod
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2020-09-08 4:28 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-08-25 2:03 [PATCH 1/6] phy: phy-bcm-ns-usb3: convert to readl_poll_timeout_atomic() Chunfeng Yun
2020-08-25 2:03 ` [PATCH 2/6] phy: phy-bcm-ns2-usbdrd: " Chunfeng Yun
2020-08-25 2:03 ` [PATCH 3/6] phy: phy-bcm-sr-usb: " Chunfeng Yun
2020-08-25 2:03 ` [PATCH 4/6] phy: phy-qcom-apq8064-sata: convert to readl_relaxed_poll_timeout() Chunfeng Yun
2020-08-25 2:03 ` [PATCH 5/6] phy: phy-pxa-28nm-hsic: convert to readl_poll_timeout() Chunfeng Yun
2020-08-25 2:03 ` [PATCH 6/6] phy: phy-pxa-28nm-usb2: " Chunfeng Yun
2020-09-08 4:26 ` [PATCH 1/6] phy: phy-bcm-ns-usb3: convert to readl_poll_timeout_atomic() Vinod Koul
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).