[PATCH v11 0/8] Move Hisilicon 6421v600 SPMI and USB drivers out of staging

[PATCH v11 0/8] Move Hisilicon 6421v600 SPMI and USB drivers out of staging

[Mauro Carvalho Chehab]

Hi Greg,

As promised, that's the version 11, meant to be applied after -rc1.

It depends on a regression fix patch merged via the regulator's tree:

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git/commit/?h=for-5.14&id=5db5dd5be70eaf808d9fd90174b957fc5c2912cb

(the dependence is just because of a trivial merge conflict)

This series contain the final bits needed for the USB3 bus to work
without staging drivers on Hikey 970.

Mauro Carvalho Chehab (8):
  staging: hi6421-spmi-pmic:  add a missing dot at copyright
  regulator: hi6421v600-regulator: add a missing dot at copyright
  staging: hikey9xx: split hi6421v600 irq into a separate driver
  staging: hi6421-spmi-pmic: cleanup drvdata
  staging: hi6421-spmi-pmic: rename spmi_device struct
  mfd: hi6421-spmi-pmic: move driver from staging
  dts: hisilicon: add support for the PMIC found on Hikey 970
  dts: hisilicon: add support for USB3 on Hikey 970

 .../mfd/hisilicon,hi6421-spmi-pmic.yaml       | 134 ++++++++
 MAINTAINERS                                   |   7 +
 .../boot/dts/hisilicon/hi3670-hikey970.dts    | 129 ++++++--
 arch/arm64/boot/dts/hisilicon/hi3670.dtsi     |  56 ++++
 .../boot/dts/hisilicon/hikey970-pmic.dtsi     |  87 +++++
 drivers/mfd/Kconfig                           |  16 +
 drivers/mfd/Makefile                          |   1 +
 drivers/mfd/hi6421-spmi-pmic.c                |  66 ++++
 drivers/misc/Kconfig                          |  10 +
 drivers/misc/Makefile                         |   1 +
 drivers/misc/hi6421v600-irq.c                 | 313 ++++++++++++++++++
 drivers/regulator/hi6421v600-regulator.c      |  12 +-
 drivers/staging/Kconfig                       |   2 -
 drivers/staging/Makefile                      |   1 -
 drivers/staging/hikey9xx/Kconfig              |  19 --
 drivers/staging/hikey9xx/Makefile             |   3 -
 drivers/staging/hikey9xx/TODO                 |   5 -
 drivers/staging/hikey9xx/hi6421-spmi-pmic.c   | 311 -----------------
 .../hikey9xx/hisilicon,hi6421-spmi-pmic.yaml  | 134 --------
 include/linux/mfd/hi6421-spmi-pmic.h          |  30 --
 20 files changed, 807 insertions(+), 530 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml
 create mode 100644 arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi
 create mode 100644 drivers/mfd/hi6421-spmi-pmic.c
 create mode 100644 drivers/misc/hi6421v600-irq.c
 delete mode 100644 drivers/staging/hikey9xx/Kconfig
 delete mode 100644 drivers/staging/hikey9xx/Makefile
 delete mode 100644 drivers/staging/hikey9xx/TODO
 delete mode 100644 drivers/staging/hikey9xx/hi6421-spmi-pmic.c
 delete mode 100644 drivers/staging/hikey9xx/hisilicon,hi6421-spmi-pmic.yaml
 delete mode 100644 include/linux/mfd/hi6421-spmi-pmic.h

-- 
2.31.1



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v11 7/8] dts: hisilicon: add support for the PMIC found on Hikey 970

[Mauro Carvalho Chehab]

Add a device tree for the HiSilicon 6421v600 SPMI PMIC, used
on HiKey970 board.

As we now have support for it, change the fixed regulators
used by the SD I/O to use the proper LDO supplies.

Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
 .../boot/dts/hisilicon/hi3670-hikey970.dts    | 22 +----
 .../boot/dts/hisilicon/hikey970-pmic.dtsi     | 87 +++++++++++++++++++
 2 files changed, 90 insertions(+), 19 deletions(-)
 create mode 100644 arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi

diff --git a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
index 7f9f9886c349..5e6d7b329771 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
@@ -12,6 +12,7 @@
 
 #include "hi3670.dtsi"
 #include "hikey970-pinctrl.dtsi"
+#include "hikey970-pmic.dtsi"
 
 / {
 	model = "HiKey970";
@@ -39,23 +40,6 @@ memory@0 {
 		reg = <0x0 0x0 0x0 0x0>;
 	};
 
-	sd_1v8: regulator-1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-1.8V";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-always-on;
-	};
-
-	sd_3v3: regulator-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
 	wlan_en: wlan-en-1-8v {
 		compatible = "regulator-fixed";
 		regulator-name = "wlan-en-regulator";
@@ -402,8 +386,8 @@ &dwmmc1 {
 	pinctrl-0 = <&sd_pmx_func
 		     &sd_clk_cfg_func
 		     &sd_cfg_func>;
-	vmmc-supply = <&sd_3v3>;
-	vqmmc-supply = <&sd_1v8>;
+	vmmc-supply = <&ldo16>;
+	vqmmc-supply = <&ldo9>;
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi b/arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi
new file mode 100644
index 000000000000..48c739eacba0
--- /dev/null
+++ b/arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Hi6421v600 SPMI PMIC used at the HiKey970 Development Board
+ *
+ * Copyright (C) 2020, Huawei Tech. Co., Ltd.
+ */
+
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	spmi: spmi@fff24000 {
+		compatible = "hisilicon,kirin970-spmi-controller";
+		#address-cells = <2>;
+		#size-cells = <0>;
+		status = "okay";
+		reg = <0x0 0xfff24000 0x0 0x1000>;
+		hisilicon,spmi-channel = <2>;
+
+		pmic: pmic@0 {
+			compatible = "hisilicon,hi6421-spmi";
+			reg = <0 SPMI_USID>;
+
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			gpios = <&gpio28 0 0>;
+
+			regulators {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ldo3: LDO3 { /* HDMI */
+					regulator-name = "ldo3";
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <2000000>;
+					regulator-boot-on;
+				};
+
+				ldo4: LDO4 { /* 40 PIN */
+					regulator-name = "ldo4";
+					regulator-min-microvolt = <1725000>;
+					regulator-max-microvolt = <1900000>;
+					regulator-boot-on;
+				};
+
+				ldo9: LDO9 { /* SDCARD I/O */
+					regulator-name = "ldo9";
+					regulator-min-microvolt = <1750000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+				};
+
+				ldo15: LDO15 { /* UFS */
+					regulator-name = "ldo15";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-always-on;
+				};
+
+				ldo16: LDO16 { /* SD */
+					regulator-name = "ldo16";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-boot-on;
+				};
+
+				ldo17: LDO17 { /* USB HUB */
+					regulator-name = "ldo17";
+					regulator-min-microvolt = <2500000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				ldo33: LDO33 { /* PEX8606 */
+					regulator-name = "ldo33";
+					regulator-min-microvolt = <2500000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+				};
+
+				ldo34: LDO34 { /* GPS AUX IN VDD */
+					regulator-name = "ldo34";
+					regulator-min-microvolt = <2600000>;
+					regulator-max-microvolt = <3300000>;
+				};
+			};
+		};
+	};
+};
-- 
2.31.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v11 8/8] dts: hisilicon: add support for USB3 on Hikey 970

[Mauro Carvalho Chehab]

Add the USB3 bindings for Kirin 970 phy and Hikey 970 board.

Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
 .../boot/dts/hisilicon/hi3670-hikey970.dts    | 107 ++++++++++++++++++
 arch/arm64/boot/dts/hisilicon/hi3670.dtsi     |  56 +++++++++
 2 files changed, 163 insertions(+)

diff --git a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
index 5e6d7b329771..9e3dfe877ebe 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
@@ -53,6 +53,30 @@ wlan_en: wlan-en-1-8v {
 		startup-delay-us = <70000>;
 		enable-active-high;
 	};
+
+	hikey_usbhub: hikey_usbhub {
+		compatible = "hisilicon,kirin970_hikey_usbhub";
+
+		typec-vbus-gpios = <&gpio26 1 0>;
+		otg-switch-gpios = <&gpio4 2 0>;
+		hub_reset_en_gpio = <&gpio0 3 0>;
+		hub-vdd-supply = <&ldo17>;
+		usb-role-switch;
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			hikey_usb_ep0: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&dwc3_role_switch>;
+			};
+			hikey_usb_ep1: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&rt1711h_ep>;
+			};
+		};
+	};
 };
 
 /*
@@ -430,3 +454,86 @@ &uart6 {
 	label = "LS-UART1";
 	status = "okay";
 };
+
+&usb_phy {
+	phy-supply = <&ldo17>;
+};
+
+&i2c1 {
+	status = "okay";
+
+	rt1711h: rt1711h@4e {
+		compatible = "richtek,rt1711h";
+		reg = <0x4e>;
+		status = "okay";
+		interrupt-parent = <&gpio27>;
+		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_cfg_func>;
+
+		usb_con: connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			data-role = "dual";
+			power-role = "dual";
+			try-power-role = "sink";
+			source-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)>;
+			sink-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)
+				PDO_VAR(5000, 5000, 1000)>;
+			op-sink-microwatt = <10000000>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@1 {
+					reg = <1>;
+					usb_con_ss: endpoint {
+						remote-endpoint = <&dwc3_ss>;
+					};
+				};
+			};
+		};
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			rt1711h_ep: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&hikey_usb_ep1>;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	/* USB HUB is on this bus at address 0x44 */
+	status = "okay";
+};
+
+&dwc3 { /* USB */
+	dr_mode = "otg";
+	maximum-speed = "super-speed";
+	phy_type = "utmi";
+	snps,dis-del-phy-power-chg-quirk;
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,tx_de_emphasis_quirk;
+	snps,tx_de_emphasis = <1>;
+	snps,dis-split-quirk;
+	snps,gctl-reset-quirk;
+	usb-role-switch;
+	role-switch-default-mode = "host";
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		dwc3_role_switch: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&hikey_usb_ep0>;
+		};
+
+		dwc3_ss: endpoint@1 {
+			reg = <1>;
+			remote-endpoint = <&usb_con_ss>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
index 8830795c8efc..6476149d99e3 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
@@ -8,6 +8,7 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/hi3670-clock.h>
+#include <dt-bindings/usb/pd.h>
 
 / {
 	compatible = "hisilicon,hi3670";
@@ -785,5 +786,60 @@ i2c4: i2c@fdf0d000 {
 			pinctrl-0 = <&i2c4_pmx_func &i2c4_cfg_func>;
 			status = "disabled";
 		};
+
+		usb3_otg_bc: usb3_otg_bc@ff200000 {
+			compatible = "syscon", "simple-mfd";
+			reg = <0x0 0xff200000 0x0 0x1000>;
+
+			usb_phy: usbphy {
+				compatible = "hisilicon,hi3670-usb-phy";
+				#phy-cells = <0>;
+				hisilicon,pericrg-syscon = <&crg_ctrl>;
+				hisilicon,pctrl-syscon = <&pctrl>;
+				hisilicon,sctrl-syscon = <&sctrl>;
+				hisilicon,eye-diagram-param = <0xFDFEE4>;
+				hisilicon,tx-vboost-lvl = <0x5>;
+			};
+		};
+
+		usb31_misc_rst: usb31_misc_rst_controller {
+			compatible = "hisilicon,hi3660-reset";
+			#reset-cells = <2>;
+			hisi,rst-syscon = <&usb3_otg_bc>;
+		};
+
+		usb3: hisi_dwc3 {
+			compatible = "hisilicon,hi3670-dwc3";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&crg_ctrl HI3670_CLK_GATE_ABB_USB>,
+				  <&crg_ctrl HI3670_HCLK_GATE_USB3OTG>,
+				  <&crg_ctrl HI3670_CLK_GATE_USB3OTG_REF>,
+				  <&crg_ctrl HI3670_ACLK_GATE_USB3DVFS>;
+			clock-names = "clk_gate_abb_usb",
+				      "hclk_gate_usb3otg",
+				      "clk_gate_usb3otg_ref",
+				      "aclk_gate_usb3dvfs";
+
+			assigned-clocks = <&crg_ctrl HI3670_ACLK_GATE_USB3DVFS>;
+			assigned-clock-rates = <238000000>;
+			resets = <&crg_rst 0x90 6>,
+				 <&crg_rst 0x90 7>,
+				 <&usb31_misc_rst 0xA0 8>,
+				 <&usb31_misc_rst 0xA0 9>;
+
+			dwc3: usb@ff100000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0xff100000 0x0 0x100000>;
+
+				interrupts = <0 159 IRQ_TYPE_LEVEL_HIGH>,
+					    <0 161 IRQ_TYPE_LEVEL_HIGH>;
+
+				phys = <&usb_phy>;
+				phy-names = "usb3-phy";
+			};
+		};
 	};
 };
-- 
2.31.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: (subset) [PATCH v11 0/8] Move Hisilicon 6421v600 SPMI and USB drivers out of staging

[Mark Brown]

On Fri, 2 Jul 2021 09:37:15 +0200, Mauro Carvalho Chehab wrote:
> As promised, that's the version 11, meant to be applied after -rc1.
> 
> It depends on a regression fix patch merged via the regulator's tree:
> 
> https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git/commit/?h=for-5.14&id=5db5dd5be70eaf808d9fd90174b957fc5c2912cb
> 
> (the dependence is just because of a trivial merge conflict)
> 
> [...]

Applied to

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git for-next

Thanks!

[2/8] regulator: hi6421v600-regulator: add a missing dot at copyright
      commit: e8608f8956ff4015a206f75631a266d93e84bb2d

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel