[PATCH V5 0/4] ARM: Enable thermal support for Raspberry Pi 4

[PATCH V5 0/4] ARM: Enable thermal support for Raspberry Pi 4

[Stefan Wahren]

This series enables thermal support for the Raspberry Pi 4. Neither the
bcm2835_thermal nor the brcmstb_thermal are suitable for the BCM2711.
So add a new thermal driver to read out the SoC temperature from the
AVS RO block of the BCM2711.

Changes in V5:
- git the rid of device member in private structure
- improve readability of bcm2711_get_temp
- avoid trace message in get_temp callback

Changes in V4:
- change my email address to avoid spurious characters

Changes in V3:
- add Rob's, Florian's and Nicolas' reviewed-by/tested-by
- adjust binding license
- make error pointer handling consistent

Changes in V2:
- rebase on thermal/linux-next
- convert binding to YAML
- make AVS RO block a subnode of AVS monitor and access it via syscon
- drop unnecessary TSENS clock and get the rid of remove callback
- add Florian's reviewed-by to last/unchanged patch

Stefan Wahren (4):
  dt-bindings: Add Broadcom AVS RO thermal
  thermal: Add BCM2711 thermal driver
  ARM: dts: bcm2711: Enable thermal
  ARM: configs: Build BCM2711 thermal as module

 .../bindings/thermal/brcm,avs-ro-thermal.yaml      |  45 ++++++++
 arch/arm/boot/dts/bcm2711.dtsi                     |  12 ++
 arch/arm/configs/multi_v7_defconfig                |   1 +
 arch/arm64/configs/defconfig                       |   1 +
 drivers/thermal/broadcom/Kconfig                   |   7 ++
 drivers/thermal/broadcom/Makefile                  |   1 +
 drivers/thermal/broadcom/bcm2711_thermal.c         | 123 +++++++++++++++++++++
 7 files changed, 190 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml
 create mode 100644 drivers/thermal/broadcom/bcm2711_thermal.c

-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V5 1/4] dt-bindings: Add Broadcom AVS RO thermal

[Stefan Wahren]

Since the BCM2711 doesn't have a AVS TMON block, the thermal information
must be retrieved from the AVS ring oscillator block. This block is part
of the AVS monitor which contains a bunch of raw sensors.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
---
 .../bindings/thermal/brcm,avs-ro-thermal.yaml      | 45 ++++++++++++++++++++++
 1 file changed, 45 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml

diff --git a/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml b/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml
new file mode 100644
index 0000000..98e7b57
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml
@@ -0,0 +1,45 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/brcm,avs-ro-thermal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom AVS ring oscillator thermal
+
+maintainers:
+  - Stefan Wahren <wahrenst@gmx.net>
+
+description: |+
+  The thermal node should be the child of a syscon node with the
+  required property:
+
+  - compatible: Should be one of the following:
+                "brcm,bcm2711-avs-monitor", "syscon", "simple-mfd"
+
+  Refer to the the bindings described in
+  Documentation/devicetree/bindings/mfd/syscon.txt
+
+properties:
+  compatible:
+    const: brcm,bcm2711-thermal
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+        avs-monitor@7d5d2000 {
+                compatible = "brcm,bcm2711-avs-monitor",
+                             "syscon", "simple-mfd";
+                reg = <0x7d5d2000 0xf00>;
+
+                thermal: thermal {
+                        compatible = "brcm,bcm2711-thermal";
+                        #thermal-sensor-cells = <0>;
+                };
+        };
+...
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V5 2/4] thermal: Add BCM2711 thermal driver

[Stefan Wahren]

This adds the thermal sensor driver for the Broadcom BCM2711 SoC,
which is placed on the Raspberry Pi 4. The driver only provides
SoC temperature reading so far.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
---
 drivers/thermal/broadcom/Kconfig           |   7 ++
 drivers/thermal/broadcom/Makefile          |   1 +
 drivers/thermal/broadcom/bcm2711_thermal.c | 123 +++++++++++++++++++++++++++++
 3 files changed, 131 insertions(+)
 create mode 100644 drivers/thermal/broadcom/bcm2711_thermal.c

diff --git a/drivers/thermal/broadcom/Kconfig b/drivers/thermal/broadcom/Kconfig
index cf43e15..061f1db 100644
--- a/drivers/thermal/broadcom/Kconfig
+++ b/drivers/thermal/broadcom/Kconfig
@@ -1,4 +1,11 @@
 # SPDX-License-Identifier: GPL-2.0-only
+config BCM2711_THERMAL
+	tristate "Broadcom AVS RO thermal sensor driver"
+	depends on ARCH_BCM2835 || COMPILE_TEST
+	depends on THERMAL_OF && MFD_SYSCON
+	help
+	  Support for thermal sensors on Broadcom BCM2711 SoCs.
+
 config BCM2835_THERMAL
 	tristate "Thermal sensors on bcm2835 SoC"
 	depends on ARCH_BCM2835 || COMPILE_TEST
diff --git a/drivers/thermal/broadcom/Makefile b/drivers/thermal/broadcom/Makefile
index 490ab1f..c917b24 100644
--- a/drivers/thermal/broadcom/Makefile
+++ b/drivers/thermal/broadcom/Makefile
@@ -1,4 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_BCM2711_THERMAL)		+= bcm2711_thermal.o
 obj-$(CONFIG_BCM2835_THERMAL)		+= bcm2835_thermal.o
 obj-$(CONFIG_BRCMSTB_THERMAL)		+= brcmstb_thermal.o
 obj-$(CONFIG_BCM_NS_THERMAL)		+= ns-thermal.o
diff --git a/drivers/thermal/broadcom/bcm2711_thermal.c b/drivers/thermal/broadcom/bcm2711_thermal.c
new file mode 100644
index 0000000..67c2a73
--- /dev/null
+++ b/drivers/thermal/broadcom/bcm2711_thermal.c
@@ -0,0 +1,123 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Broadcom AVS RO thermal sensor driver
+ *
+ * based on brcmstb_thermal
+ *
+ * Copyright (C) 2020 Stefan Wahren
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/thermal.h>
+
+#include "../thermal_hwmon.h"
+
+#define AVS_RO_TEMP_STATUS		0x200
+#define AVS_RO_TEMP_STATUS_VALID_MSK	(BIT(16) | BIT(10))
+#define AVS_RO_TEMP_STATUS_DATA_MSK	GENMASK(9, 0)
+
+struct bcm2711_thermal_priv {
+	struct regmap *regmap;
+	struct thermal_zone_device *thermal;
+};
+
+static int bcm2711_get_temp(void *data, int *temp)
+{
+	struct bcm2711_thermal_priv *priv = data;
+	int slope = thermal_zone_get_slope(priv->thermal);
+	int offset = thermal_zone_get_offset(priv->thermal);
+	u32 val;
+	int ret;
+	long t;
+
+	ret = regmap_read(priv->regmap, AVS_RO_TEMP_STATUS, &val);
+	if (ret)
+		return ret;
+
+	if (!(val & AVS_RO_TEMP_STATUS_VALID_MSK))
+		return -EIO;
+
+	val &= AVS_RO_TEMP_STATUS_DATA_MSK;
+
+	/* Convert a HW code to a temperature reading (millidegree celsius) */
+	t = slope * val + offset;
+
+	*temp = t < 0 ? 0 : t;
+
+	return 0;
+}
+
+static const struct thermal_zone_of_device_ops bcm2711_thermal_of_ops = {
+	.get_temp	= bcm2711_get_temp,
+};
+
+static const struct of_device_id bcm2711_thermal_id_table[] = {
+	{ .compatible = "brcm,bcm2711-thermal" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, bcm2711_thermal_id_table);
+
+static int bcm2711_thermal_probe(struct platform_device *pdev)
+{
+	struct thermal_zone_device *thermal;
+	struct bcm2711_thermal_priv *priv;
+	struct device *dev = &pdev->dev;
+	struct device_node *parent;
+	struct regmap *regmap;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	/* get regmap from syscon node */
+	parent = of_get_parent(dev->of_node); /* parent should be syscon node */
+	regmap = syscon_node_to_regmap(parent);
+	of_node_put(parent);
+	if (IS_ERR(regmap)) {
+		ret = PTR_ERR(regmap);
+		dev_err(dev, "failed to get regmap: %d\n", ret);
+		return ret;
+	}
+	priv->regmap = regmap;
+
+	thermal = devm_thermal_zone_of_sensor_register(dev, 0, priv,
+						       &bcm2711_thermal_of_ops);
+	if (IS_ERR(thermal)) {
+		ret = PTR_ERR(thermal);
+		dev_err(dev, "could not register sensor: %d\n", ret);
+		return ret;
+	}
+
+	priv->thermal = thermal;
+
+	thermal->tzp->no_hwmon = false;
+	ret = thermal_add_hwmon_sysfs(thermal);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static struct platform_driver bcm2711_thermal_driver = {
+	.probe = bcm2711_thermal_probe,
+	.driver = {
+		.name = "bcm2711_thermal",
+		.of_match_table = bcm2711_thermal_id_table,
+	},
+};
+module_platform_driver(bcm2711_thermal_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Stefan Wahren");
+MODULE_DESCRIPTION("Broadcom AVS RO thermal sensor driver");
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V5 3/4] ARM: dts: bcm2711: Enable thermal

[Stefan Wahren]

This enables thermal for the BCM2711 (used on Raspberry Pi 4) by adding
the AVS monitor and a subnode for the thermal part.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
---
 arch/arm/boot/dts/bcm2711.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/bcm2711.dtsi
index 961bed8..96f341d 100644
--- a/arch/arm/boot/dts/bcm2711.dtsi
+++ b/arch/arm/boot/dts/bcm2711.dtsi
@@ -66,6 +66,17 @@
 						 IRQ_TYPE_LEVEL_HIGH)>;
 		};
 
+		avs_monitor: avs-monitor@7d5d2000 {
+			compatible = "brcm,bcm2711-avs-monitor",
+				     "syscon", "simple-mfd";
+			reg = <0x7d5d2000 0xf00>;
+
+			thermal: thermal {
+				compatible = "brcm,bcm2711-thermal";
+				#thermal-sensor-cells = <0>;
+			};
+		};
+
 		dma: dma@7e007000 {
 			compatible = "brcm,bcm2835-dma";
 			reg = <0x7e007000 0xb00>;
@@ -363,6 +374,7 @@
 
 &cpu_thermal {
 	coefficients = <(-487) 410040>;
+	thermal-sensors = <&thermal>;
 };
 
 &dsi0 {
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V5 4/4] ARM: configs: Build BCM2711 thermal as module

[Stefan Wahren]

This builds the BCM2711 thermal driver as module for the Raspberry Pi 4.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
---
 arch/arm/configs/multi_v7_defconfig | 1 +
 arch/arm64/configs/defconfig        | 1 +
 2 files changed, 2 insertions(+)

diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index 3f1b96d..f5d19cc 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -496,6 +496,7 @@ CONFIG_IMX_THERMAL=y
 CONFIG_ROCKCHIP_THERMAL=y
 CONFIG_RCAR_THERMAL=y
 CONFIG_ARMADA_THERMAL=y
+CONFIG_BCM2711_THERMAL=m
 CONFIG_BCM2835_THERMAL=m
 CONFIG_BRCMSTB_THERMAL=m
 CONFIG_ST_THERMAL_MEMMAP=y
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 6a83ba2..b2f6673 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -442,6 +442,7 @@ CONFIG_ROCKCHIP_THERMAL=m
 CONFIG_RCAR_THERMAL=y
 CONFIG_RCAR_GEN3_THERMAL=y
 CONFIG_ARMADA_THERMAL=y
+CONFIG_BCM2711_THERMAL=m
 CONFIG_BCM2835_THERMAL=m
 CONFIG_BRCMSTB_THERMAL=m
 CONFIG_EXYNOS_THERMAL=y
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V5 0/4] ARM: Enable thermal support for Raspberry Pi 4

[Daniel Lezcano]

Hi Stefan,

how do you want the series merged?

On 13/01/2020 19:56, Stefan Wahren wrote:
> This series enables thermal support for the Raspberry Pi 4. Neither the
> bcm2835_thermal nor the brcmstb_thermal are suitable for the BCM2711.
> So add a new thermal driver to read out the SoC temperature from the
> AVS RO block of the BCM2711.
> 
> Changes in V5:
> - git the rid of device member in private structure
> - improve readability of bcm2711_get_temp
> - avoid trace message in get_temp callback
> 
> Changes in V4:
> - change my email address to avoid spurious characters
> 
> Changes in V3:
> - add Rob's, Florian's and Nicolas' reviewed-by/tested-by
> - adjust binding license
> - make error pointer handling consistent
> 
> Changes in V2:
> - rebase on thermal/linux-next
> - convert binding to YAML
> - make AVS RO block a subnode of AVS monitor and access it via syscon
> - drop unnecessary TSENS clock and get the rid of remove callback
> - add Florian's reviewed-by to last/unchanged patch
> 
> Stefan Wahren (4):
>   dt-bindings: Add Broadcom AVS RO thermal
>   thermal: Add BCM2711 thermal driver
>   ARM: dts: bcm2711: Enable thermal
>   ARM: configs: Build BCM2711 thermal as module
> 
>  .../bindings/thermal/brcm,avs-ro-thermal.yaml      |  45 ++++++++
>  arch/arm/boot/dts/bcm2711.dtsi                     |  12 ++
>  arch/arm/configs/multi_v7_defconfig                |   1 +
>  arch/arm64/configs/defconfig                       |   1 +
>  drivers/thermal/broadcom/Kconfig                   |   7 ++
>  drivers/thermal/broadcom/Makefile                  |   1 +
>  drivers/thermal/broadcom/bcm2711_thermal.c         | 123 +++++++++++++++++++++
>  7 files changed, 190 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml
>  create mode 100644 drivers/thermal/broadcom/bcm2711_thermal.c
> 


-- 
 <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V5 0/4] ARM: Enable thermal support for Raspberry Pi 4

[Stefan Wahren]

Hi Daniel,

Am 13.01.20 um 20:10 schrieb Daniel Lezcano:
> Hi Stefan,
>
> how do you want the series merged?

i'm not BCM2835 maintainer anymore, so the final decision is up to
Nicolas or Florian.

But if i can make a wish, it would be nice to take as much as possible
via the thermal tree, because Nicolas already sent the pull requests for
5.6.

Thanks
Stefan


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V5 0/4] ARM: Enable thermal support for Raspberry Pi 4

[Daniel Lezcano]

On 13/01/2020 20:20, Stefan Wahren wrote:
> Hi Daniel,
> 
> Am 13.01.20 um 20:10 schrieb Daniel Lezcano:
>> Hi Stefan,
>>
>> how do you want the series merged?
> 
> i'm not BCM2835 maintainer anymore, so the final decision is up to
> Nicolas or Florian.
> 
> But if i can make a wish, it would be nice to take as much as possible
> via the thermal tree, because Nicolas already sent the pull requests for
> 5.6.

Ok, I can take the series if it is fine for everyone else.


-- 
 <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V5 0/4] ARM: Enable thermal support for Raspberry Pi 4

[Nicolas Saenz Julienne]

[-- Attachment #1.1: Type: text/plain, Size: 625 bytes --]

On Mon, 2020-01-13 at 20:24 +0100, Daniel Lezcano wrote:
> On 13/01/2020 20:20, Stefan Wahren wrote:
> > Hi Daniel,
> > 
> > Am 13.01.20 um 20:10 schrieb Daniel Lezcano:
> > > Hi Stefan,
> > > 
> > > how do you want the series merged?
> > 
> > i'm not BCM2835 maintainer anymore, so the final decision is up to
> > Nicolas or Florian.
> > 
> > But if i can make a wish, it would be nice to take as much as possible
> > via the thermal tree, because Nicolas already sent the pull requests for
> > 5.6.
> 
> Ok, I can take the series if it is fine for everyone else.

Sounds good to me. Thanks!

Nicolas


[-- Attachment #1.2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V5 3/4] ARM: dts: bcm2711: Enable thermal

[Florian Fainelli]

On 1/13/20 10:56 AM, Stefan Wahren wrote:
> This enables thermal for the BCM2711 (used on Raspberry Pi 4) by adding
> the AVS monitor and a subnode for the thermal part.
> 
> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
> Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
-- 
Florian

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V5 0/4] ARM: Enable thermal support for Raspberry Pi 4

[Florian Fainelli]

On 1/13/20 11:54 AM, Nicolas Saenz Julienne wrote:
> On Mon, 2020-01-13 at 20:24 +0100, Daniel Lezcano wrote:
>> On 13/01/2020 20:20, Stefan Wahren wrote:
>>> Hi Daniel,
>>>
>>> Am 13.01.20 um 20:10 schrieb Daniel Lezcano:
>>>> Hi Stefan,
>>>>
>>>> how do you want the series merged?
>>>
>>> i'm not BCM2835 maintainer anymore, so the final decision is up to
>>> Nicolas or Florian.
>>>
>>> But if i can make a wish, it would be nice to take as much as possible
>>> via the thermal tree, because Nicolas already sent the pull requests for
>>> 5.6.
>>
>> Ok, I can take the series if it is fine for everyone else.
> 
> Sounds good to me. Thanks!

Works for me as well, thanks!
-- 
-- 
Florian

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V5 1/4] dt-bindings: Add Broadcom AVS RO thermal

[Rob Herring]

On Mon, Jan 13, 2020 at 12:56 PM Stefan Wahren <stefan.wahren@i2se.com> wrote:
>
> Since the BCM2711 doesn't have a AVS TMON block, the thermal information
> must be retrieved from the AVS ring oscillator block. This block is part
> of the AVS monitor which contains a bunch of raw sensors.
>
> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
> ---
>  .../bindings/thermal/brcm,avs-ro-thermal.yaml      | 45 ++++++++++++++++++++++
>  1 file changed, 45 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml

The example fails 'make dt_binding_check':

/builds/robherring/linux-dt-bindings/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.example.dt.yaml:
thermal: 'reg' is a required property

> diff --git a/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml b/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml
> new file mode 100644
> index 0000000..98e7b57
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml
> @@ -0,0 +1,45 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/thermal/brcm,avs-ro-thermal.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Broadcom AVS ring oscillator thermal
> +
> +maintainers:
> +  - Stefan Wahren <wahrenst@gmx.net>
> +
> +description: |+
> +  The thermal node should be the child of a syscon node with the
> +  required property:
> +
> +  - compatible: Should be one of the following:
> +                "brcm,bcm2711-avs-monitor", "syscon", "simple-mfd"
> +
> +  Refer to the the bindings described in
> +  Documentation/devicetree/bindings/mfd/syscon.txt
> +
> +properties:
> +  compatible:
> +    const: brcm,bcm2711-thermal
> +
> +  reg:
> +    maxItems: 1
> +
> +required:
> +  - compatible
> +  - reg
> +
> +examples:
> +  - |
> +        avs-monitor@7d5d2000 {
> +                compatible = "brcm,bcm2711-avs-monitor",
> +                             "syscon", "simple-mfd";
> +                reg = <0x7d5d2000 0xf00>;
> +
> +                thermal: thermal {
> +                        compatible = "brcm,bcm2711-thermal";
> +                        #thermal-sensor-cells = <0>;

Also this is not documented. That's not caught because
'additionalProperties: false' is also needed.

Rob

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V5 1/4] dt-bindings: Add Broadcom AVS RO thermal

[Stefan Wahren]

Hi Rob,

Am 16.01.20 um 18:33 schrieb Rob Herring:
> On Mon, Jan 13, 2020 at 12:56 PM Stefan Wahren <stefan.wahren@i2se.com> wrote:
>> Since the BCM2711 doesn't have a AVS TMON block, the thermal information
>> must be retrieved from the AVS ring oscillator block. This block is part
>> of the AVS monitor which contains a bunch of raw sensors.
>>
>> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
>> Reviewed-by: Rob Herring <robh@kernel.org>
>> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
>> ---
>>  .../bindings/thermal/brcm,avs-ro-thermal.yaml      | 45 ++++++++++++++++++++++
>>  1 file changed, 45 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml
> The example fails 'make dt_binding_check':
>
> /builds/robherring/linux-dt-bindings/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.example.dt.yaml:
> thermal: 'reg' is a required property

can you please explain what is the reason for this? The example below
has a reg property. I'm confused.

Best regards
Stefan

>
>> diff --git a/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml b/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml
>> new file mode 100644
>> index 0000000..98e7b57
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml
>> @@ -0,0 +1,45 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/thermal/brcm,avs-ro-thermal.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Broadcom AVS ring oscillator thermal
>> +
>> +maintainers:
>> +  - Stefan Wahren <wahrenst@gmx.net>
>> +
>> +description: |+
>> +  The thermal node should be the child of a syscon node with the
>> +  required property:
>> +
>> +  - compatible: Should be one of the following:
>> +                "brcm,bcm2711-avs-monitor", "syscon", "simple-mfd"
>> +
>> +  Refer to the the bindings described in
>> +  Documentation/devicetree/bindings/mfd/syscon.txt
>> +
>> +properties:
>> +  compatible:
>> +    const: brcm,bcm2711-thermal
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +
>> +examples:
>> +  - |
>> +        avs-monitor@7d5d2000 {
>> +                compatible = "brcm,bcm2711-avs-monitor",
>> +                             "syscon", "simple-mfd";
>> +                reg = <0x7d5d2000 0xf00>;
>> +
>> +                thermal: thermal {
>> +                        compatible = "brcm,bcm2711-thermal";
>> +                        #thermal-sensor-cells = <0>;
> Also this is not documented. That's not caught because
> 'additionalProperties: false' is also needed.
>
> Rob

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V5 1/4] dt-bindings: Add Broadcom AVS RO thermal

[Stefan Wahren]

Am 16.01.20 um 19:23 schrieb Stefan Wahren:
> Hi Rob,
>
> Am 16.01.20 um 18:33 schrieb Rob Herring:
>> On Mon, Jan 13, 2020 at 12:56 PM Stefan Wahren <stefan.wahren@i2se.com> wrote:
>>> Since the BCM2711 doesn't have a AVS TMON block, the thermal information
>>> must be retrieved from the AVS ring oscillator block. This block is part
>>> of the AVS monitor which contains a bunch of raw sensors.
>>>
>>> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
>>> Reviewed-by: Rob Herring <robh@kernel.org>
>>> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
>>> ---
>>>  .../bindings/thermal/brcm,avs-ro-thermal.yaml      | 45 ++++++++++++++++++++++
>>>  1 file changed, 45 insertions(+)
>>>  create mode 100644 Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml
>> The example fails 'make dt_binding_check':
>>
>> /builds/robherring/linux-dt-bindings/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.example.dt.yaml:
>> thermal: 'reg' is a required property
> can you please explain what is the reason for this? The example below
> has a reg property. I'm confused.

Please ignore, i got the issue.


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel