From: megous@megous.com (megous at megous.com)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 11/14] ARM: dts: sun8i: Add sy8106a regulator to Orange Pi PC
Date: Sat, 25 Jun 2016 05:45:08 +0200 [thread overview]
Message-ID: <20160625034511.7966-12-megous@megous.com> (raw)
In-Reply-To: <20160625034511.7966-1-megous@megous.com>
From: Ondrej Jirman <megous@megous.com>
Add sy8106a regulator to r_twi bus and enable the r_twi bus on
Orange Pi PC. This regulator controls the CPUX voltage.
Signed-off-by: Ondrej Jirman <megous@megous.com>
---
arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
index daf50b9a6..79f0b49 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
@@ -90,6 +90,20 @@
};
};
+&r_twi {
+ status = "okay";
+
+ vdd_cpu: regulator at 65 {
+ compatible = "silergy,sy8106a";
+ reg = <0x65>;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-ramp-delay = <200>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
&ehci1 {
status = "okay";
};
--
2.9.0
next prev parent reply other threads:[~2016-06-25 3:45 UTC|newest]
Thread overview: 66+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-06-25 3:44 [PATCH v2] Thermal regulation for Orange Pi PC and Orange Pi One megous at megous.com
2016-06-25 3:44 ` [PATCH v2 01/14] ARM: clk: sunxi: Add driver for the H3 THS clock megous at megous.com
2016-06-25 7:13 ` Maxime Ripard
2016-06-25 15:23 ` Ondřej Jirman
2016-06-28 11:52 ` Maxime Ripard
2016-06-25 3:44 ` [PATCH v2 02/14] thermal: sun8i_ths: Add support for the thermal sensor on Allwinner H3 megous at megous.com
2016-06-25 7:10 ` Maxime Ripard
2016-06-25 15:12 ` Ondřej Jirman
2016-06-28 11:39 ` Maxime Ripard
2016-06-25 3:45 ` [PATCH v2 03/14] dt-bindings: document sun8i_ths - H3 thermal sensor driver megous at megous.com
2016-06-28 20:56 ` Rob Herring
2016-06-25 3:45 ` [PATCH v2 04/14] regulator: SY8106A regulator driver megous at megous.com
2016-06-26 11:26 ` Mark Brown
2016-06-26 15:07 ` Ondřej Jirman
2016-06-27 14:54 ` Mark Brown
2016-06-28 16:27 ` Ondřej Jirman
2016-06-27 15:10 ` Mark Brown
2016-06-25 3:45 ` [PATCH v2 05/14] dt-bindings: document " megous at megous.com
2016-06-26 11:27 ` Mark Brown
2016-06-26 15:10 ` Ondřej Jirman
2016-06-26 18:52 ` Mark Brown
2016-06-25 3:45 ` [PATCH v2 06/14] ARM: sun8i: clk: Add clk-factor rate application method megous at megous.com
2016-06-30 20:40 ` Maxime Ripard
2016-07-01 0:50 ` Ondřej Jirman
2016-07-01 5:37 ` Jean-Francois Moine
2016-07-01 6:34 ` Ondřej Jirman
2016-07-01 7:47 ` Jean-Francois Moine
2016-07-15 8:53 ` Maxime Ripard
2016-07-15 10:38 ` Ondřej Jirman
2016-07-15 13:27 ` Jean-Francois Moine
2016-07-15 13:48 ` Ondřej Jirman
2016-07-15 14:22 ` [linux-sunxi] " Michal Suchanek
2016-07-15 16:33 ` Ondřej Jirman
2016-07-21 9:51 ` Maxime Ripard
2016-07-21 9:48 ` Maxime Ripard
2016-07-21 9:52 ` Ondřej Jirman
2016-07-26 6:32 ` Maxime Ripard
2016-07-28 11:27 ` Changed: sunxi-ng clock code - NKMP clock implementation is wrong Ondřej Jirman
2016-07-28 11:38 ` [linux-sunxi] " Chen-Yu Tsai
2016-07-28 21:00 ` Maxime Ripard
2016-07-28 22:01 ` Ondřej Jirman
2016-07-31 10:31 ` Maxime Ripard
2016-07-31 22:01 ` Ondřej Jirman
2016-08-31 20:25 ` Maxime Ripard
2016-07-01 0:53 ` [PATCH v2 06/14] ARM: sun8i: clk: Add clk-factor rate application method Ondřej Jirman
2016-07-15 8:19 ` Maxime Ripard
2016-06-25 3:45 ` [PATCH v2 07/14] ARM: dts: sun8i: Use sun8i-h3-pll1-clk for pll1 in H3 megous at megous.com
2016-06-25 3:45 ` [PATCH v2 08/14] ARM: dts: sun8i: Add thermal sensor node to the sun8i-h3.dtsi megous at megous.com
2016-06-25 3:45 ` [PATCH v2 09/14] ARM: dts: sun8i: Add cpu0 label to sun8i-h3.dtsi megous at megous.com
2016-06-25 3:45 ` [PATCH v2 10/14] ARM: dts: sun8i: Add r_twi I2C controller megous at megous.com
2016-06-25 7:16 ` Maxime Ripard
2016-06-25 3:45 ` megous at megous.com [this message]
2016-06-25 3:45 ` [PATCH v2 12/14] ARM: dts: sun8i: Setup CPU operating points for Onrage PI PC megous at megous.com
2016-06-25 3:45 ` [PATCH v2 13/14] ARM: dts: sun8i: Add gpio-regulator used on Orange Pi One megous at megous.com
2016-06-25 7:18 ` Maxime Ripard
2016-06-25 3:45 ` [PATCH v2 14/14] ARM: dts: sun8i: Enable DVFS " megous at megous.com
2016-06-30 11:13 ` [linux-sunxi] " Michal Suchanek
2016-06-30 14:19 ` Ondřej Jirman
2016-06-30 15:16 ` Michal Suchanek
2016-06-30 15:32 ` Ondřej Jirman
2016-06-30 15:50 ` Michal Suchanek
2016-06-30 15:53 ` Ondřej Jirman
2016-07-01 10:54 ` Michal Suchanek
2016-06-30 14:23 ` Siarhei Siamashka
2016-07-01 1:17 ` Ondřej Jirman
2016-07-22 0:41 ` Ondřej Jirman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20160625034511.7966-12-megous@megous.com \
--to=megous@megous.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).