From: megous@megous.com (megous at megous.com)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 07/14] ARM: dts: sun8i: Use sun8i-h3-pll1-clk for pll1 in H3
Date: Sat, 25 Jun 2016 05:45:04 +0200 [thread overview]
Message-ID: <20160625034511.7966-8-megous@megous.com> (raw)
In-Reply-To: <20160625034511.7966-1-megous@megous.com>
From: Ondrej Jirman <megous@megous.com>
PLL1 on H3 requires special factors application algorithm,
when the rate is changed. This algorithm was extracted
from the arisc code that handles frequency scaling
in the BSP kernel.
This algorithm is implemented by sun8i-h3-pll1-clk.
Signed-off-by: Ondrej Jirman <megous@megous.com>
---
arch/arm/boot/dts/sun8i-h3.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index 4a4926b..b3247f4 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -106,7 +106,7 @@
pll1: clk at 01c20000 {
#clock-cells = <0>;
- compatible = "allwinner,sun8i-a23-pll1-clk";
+ compatible = "allwinner,sun8i-h3-pll1-clk";
reg = <0x01c20000 0x4>;
clocks = <&osc24M>;
clock-output-names = "pll1";
--
2.9.0
next prev parent reply other threads:[~2016-06-25 3:45 UTC|newest]
Thread overview: 66+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-06-25 3:44 [PATCH v2] Thermal regulation for Orange Pi PC and Orange Pi One megous at megous.com
2016-06-25 3:44 ` [PATCH v2 01/14] ARM: clk: sunxi: Add driver for the H3 THS clock megous at megous.com
2016-06-25 7:13 ` Maxime Ripard
2016-06-25 15:23 ` Ondřej Jirman
2016-06-28 11:52 ` Maxime Ripard
2016-06-25 3:44 ` [PATCH v2 02/14] thermal: sun8i_ths: Add support for the thermal sensor on Allwinner H3 megous at megous.com
2016-06-25 7:10 ` Maxime Ripard
2016-06-25 15:12 ` Ondřej Jirman
2016-06-28 11:39 ` Maxime Ripard
2016-06-25 3:45 ` [PATCH v2 03/14] dt-bindings: document sun8i_ths - H3 thermal sensor driver megous at megous.com
2016-06-28 20:56 ` Rob Herring
2016-06-25 3:45 ` [PATCH v2 04/14] regulator: SY8106A regulator driver megous at megous.com
2016-06-26 11:26 ` Mark Brown
2016-06-26 15:07 ` Ondřej Jirman
2016-06-27 14:54 ` Mark Brown
2016-06-28 16:27 ` Ondřej Jirman
2016-06-27 15:10 ` Mark Brown
2016-06-25 3:45 ` [PATCH v2 05/14] dt-bindings: document " megous at megous.com
2016-06-26 11:27 ` Mark Brown
2016-06-26 15:10 ` Ondřej Jirman
2016-06-26 18:52 ` Mark Brown
2016-06-25 3:45 ` [PATCH v2 06/14] ARM: sun8i: clk: Add clk-factor rate application method megous at megous.com
2016-06-30 20:40 ` Maxime Ripard
2016-07-01 0:50 ` Ondřej Jirman
2016-07-01 5:37 ` Jean-Francois Moine
2016-07-01 6:34 ` Ondřej Jirman
2016-07-01 7:47 ` Jean-Francois Moine
2016-07-15 8:53 ` Maxime Ripard
2016-07-15 10:38 ` Ondřej Jirman
2016-07-15 13:27 ` Jean-Francois Moine
2016-07-15 13:48 ` Ondřej Jirman
2016-07-15 14:22 ` [linux-sunxi] " Michal Suchanek
2016-07-15 16:33 ` Ondřej Jirman
2016-07-21 9:51 ` Maxime Ripard
2016-07-21 9:48 ` Maxime Ripard
2016-07-21 9:52 ` Ondřej Jirman
2016-07-26 6:32 ` Maxime Ripard
2016-07-28 11:27 ` Changed: sunxi-ng clock code - NKMP clock implementation is wrong Ondřej Jirman
2016-07-28 11:38 ` [linux-sunxi] " Chen-Yu Tsai
2016-07-28 21:00 ` Maxime Ripard
2016-07-28 22:01 ` Ondřej Jirman
2016-07-31 10:31 ` Maxime Ripard
2016-07-31 22:01 ` Ondřej Jirman
2016-08-31 20:25 ` Maxime Ripard
2016-07-01 0:53 ` [PATCH v2 06/14] ARM: sun8i: clk: Add clk-factor rate application method Ondřej Jirman
2016-07-15 8:19 ` Maxime Ripard
2016-06-25 3:45 ` megous at megous.com [this message]
2016-06-25 3:45 ` [PATCH v2 08/14] ARM: dts: sun8i: Add thermal sensor node to the sun8i-h3.dtsi megous at megous.com
2016-06-25 3:45 ` [PATCH v2 09/14] ARM: dts: sun8i: Add cpu0 label to sun8i-h3.dtsi megous at megous.com
2016-06-25 3:45 ` [PATCH v2 10/14] ARM: dts: sun8i: Add r_twi I2C controller megous at megous.com
2016-06-25 7:16 ` Maxime Ripard
2016-06-25 3:45 ` [PATCH v2 11/14] ARM: dts: sun8i: Add sy8106a regulator to Orange Pi PC megous at megous.com
2016-06-25 3:45 ` [PATCH v2 12/14] ARM: dts: sun8i: Setup CPU operating points for Onrage PI PC megous at megous.com
2016-06-25 3:45 ` [PATCH v2 13/14] ARM: dts: sun8i: Add gpio-regulator used on Orange Pi One megous at megous.com
2016-06-25 7:18 ` Maxime Ripard
2016-06-25 3:45 ` [PATCH v2 14/14] ARM: dts: sun8i: Enable DVFS " megous at megous.com
2016-06-30 11:13 ` [linux-sunxi] " Michal Suchanek
2016-06-30 14:19 ` Ondřej Jirman
2016-06-30 15:16 ` Michal Suchanek
2016-06-30 15:32 ` Ondřej Jirman
2016-06-30 15:50 ` Michal Suchanek
2016-06-30 15:53 ` Ondřej Jirman
2016-07-01 10:54 ` Michal Suchanek
2016-06-30 14:23 ` Siarhei Siamashka
2016-07-01 1:17 ` Ondřej Jirman
2016-07-22 0:41 ` Ondřej Jirman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20160625034511.7966-8-megous@megous.com \
--to=megous@megous.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).