From: hzpeterchen@gmail.com (Peter Chen)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 06/22] usb: chipidea: Add platform flag for wrapper phy management
Date: Fri, 8 Jul 2016 17:25:35 +0800 [thread overview]
Message-ID: <20160708092535.GD20485@shlinux2> (raw)
In-Reply-To: <20160707222114.1673-7-stephen.boyd@linaro.org>
On Thu, Jul 07, 2016 at 03:20:57PM -0700, Stephen Boyd wrote:
> The ULPI phy on qcom platforms needs to be initialized and
> powered on after a USB reset and before we toggle the run/stop
> bit. Otherwise, the phy locks up and doesn't work properly.
> Therefore, add a flag to skip any phy power management in the
> core layer, leaving it up to the glue driver to manage.
>
> Cc: Peter Chen <peter.chen@nxp.com>
> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
> ---
> drivers/usb/chipidea/core.c | 6 ++++++
> include/linux/usb/chipidea.h | 1 +
> 2 files changed, 7 insertions(+)
>
> diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
> index 01390e02ee53..532085a096d9 100644
> --- a/drivers/usb/chipidea/core.c
> +++ b/drivers/usb/chipidea/core.c
> @@ -361,6 +361,9 @@ static int _ci_usb_phy_init(struct ci_hdrc *ci)
> */
> static void ci_usb_phy_exit(struct ci_hdrc *ci)
> {
> + if (ci->platdata->flags & CI_HDRC_OVERRIDE_PHY_CONTROL)
> + return;
> +
> if (ci->phy) {
> phy_power_off(ci->phy);
> phy_exit(ci->phy);
> @@ -379,6 +382,9 @@ static int ci_usb_phy_init(struct ci_hdrc *ci)
> {
> int ret;
>
> + if (ci->platdata->flags & CI_HDRC_OVERRIDE_PHY_CONTROL)
> + return 0;
> +
How you handle the code for PHY getting at probe?
--
Best Regards,
Peter Chen
next prev parent reply other threads:[~2016-07-08 9:25 UTC|newest]
Thread overview: 65+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-07-07 22:20 [PATCH v2 00/22] Support qcom's HSIC USB and rewrite USB2 HS phy support Stephen Boyd
2016-07-07 22:20 ` [PATCH v2 01/22] of: device: Support loading a module with OF based modalias Stephen Boyd
2016-07-07 22:20 ` [PATCH v2 02/22] of: device: Export of_device_{get_modalias, uvent_modalias} to modules Stephen Boyd
2016-07-07 22:20 ` [PATCH v2 03/22] usb: ulpi: Support device discovery via device properties Stephen Boyd
2016-07-08 9:04 ` Peter Chen
2016-08-05 21:27 ` Stephen Boyd
2016-08-23 19:58 ` Stephen Boyd
2016-08-24 7:31 ` Heikki Krogerus
2016-08-26 18:54 ` Stephen Boyd
2016-07-18 2:23 ` Rob Herring
2016-08-05 21:40 ` Stephen Boyd
2016-08-23 20:00 ` Stephen Boyd
2016-08-23 23:06 ` Rob Herring
2016-08-24 1:06 ` Stephen Boyd
2016-07-07 22:20 ` [PATCH v2 04/22] usb: chipidea: Only read/write OTGSC from one place Stephen Boyd
2016-07-08 9:14 ` Peter Chen
2016-08-05 21:41 ` Stephen Boyd
2016-08-06 7:42 ` Peter Chen
2016-07-07 22:20 ` [PATCH v2 05/22] usb: chipidea: Handle extcon events properly Stephen Boyd
2016-07-07 22:20 ` [PATCH v2 06/22] usb: chipidea: Add platform flag for wrapper phy management Stephen Boyd
2016-07-08 9:25 ` Peter Chen [this message]
2016-08-05 21:46 ` Stephen Boyd
2016-08-06 7:59 ` Peter Chen
2016-08-08 23:46 ` Stephen Boyd
2016-08-09 0:36 ` Peter Chen
2016-07-07 22:20 ` [PATCH v2 07/22] usb: chipidea: Notify events when switching host mode Stephen Boyd
2016-07-08 9:29 ` Peter Chen
2016-07-07 22:20 ` [PATCH v2 08/22] usb: chipidea: Remove locking in ci_udc_start() Stephen Boyd
2016-07-08 9:45 ` Peter Chen
2016-08-05 21:53 ` Stephen Boyd
2016-08-06 7:54 ` Peter Chen
2016-08-08 23:47 ` Stephen Boyd
2016-08-09 0:42 ` Peter Chen
2016-07-07 22:21 ` [PATCH v2 09/22] usb: chipidea: Kick OTG state machine for AVVIS with vbus extcon Stephen Boyd
2016-07-11 2:25 ` Peter Chen
2016-07-07 22:21 ` [PATCH v2 10/22] usb: chipidea: Add support for ULPI PHY bus Stephen Boyd
2016-07-11 3:10 ` Peter Chen
2016-07-11 22:02 ` Stephen Boyd
2016-07-07 22:21 ` [PATCH v2 11/22] usb: chipidea: msm: Mark device as runtime pm active Stephen Boyd
2016-07-11 3:19 ` Peter Chen
2016-07-07 22:21 ` [PATCH v2 12/22] usb: chipidea: msm: Rely on core to override AHBBURST Stephen Boyd
2016-07-11 3:24 ` Peter Chen
2016-07-07 22:21 ` [PATCH v2 13/22] usb: chipidea: msm: Use hw_write_id_reg() instead of writel Stephen Boyd
2016-07-07 22:21 ` [PATCH v2 14/22] usb: chipidea: msm: Add proper clk and reset support Stephen Boyd
2016-07-11 4:32 ` Peter Chen
2016-07-07 22:21 ` [PATCH v2 15/22] usb: chipidea: msm: Mux over secondary phy at the right time Stephen Boyd
2016-07-11 4:43 ` Peter Chen
2016-07-11 22:03 ` Stephen Boyd
2016-07-12 1:07 ` Peter Chen
2016-07-07 22:21 ` [PATCH v2 16/22] usb: chipidea: msm: Restore wrapper settings after reset Stephen Boyd
2016-07-11 5:24 ` Peter Chen
2016-07-07 22:21 ` [PATCH v2 17/22] usb: chipidea: msm: Make platform data driver local instead of global Stephen Boyd
2016-07-11 5:26 ` Peter Chen
2016-07-07 22:21 ` [PATCH v2 18/22] usb: chipidea: msm: Add reset controller for PHY POR bit Stephen Boyd
2016-07-11 5:32 ` Peter Chen
2016-07-11 22:07 ` Stephen Boyd
2016-07-12 1:09 ` Peter Chen
2016-07-07 22:21 ` [PATCH v2 19/22] usb: chipidea: msm: Handle phy power states Stephen Boyd
2016-07-11 5:38 ` Peter Chen
2016-07-07 22:21 ` [PATCH v2 20/22] usb: chipidea: msm: Be silent on probe defer errors Stephen Boyd
2016-07-11 5:39 ` Peter Chen
2016-07-07 22:21 ` [PATCH v2 21/22] phy: Add support for Qualcomm's USB HSIC phy Stephen Boyd
2016-07-18 2:27 ` Rob Herring
2016-07-07 22:21 ` [PATCH v2 22/22] phy: Add support for Qualcomm's USB HS phy Stephen Boyd
2016-07-18 2:28 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20160708092535.GD20485@shlinux2 \
--to=hzpeterchen@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).