[PATCH V2 0/2] ARM: dts: Introduce support for rev BeagleBoard-X15 B1

[PATCH V2 0/2] ARM: dts: Introduce support for rev BeagleBoard-X15 B1

[Nishanth Menon]

Hi,

Please find the series to cleanup and support Production version of
Beagleboard-X15 rev B1 support.

More  details can be found at https://github.com/beagleboard/beagleboard-x15

Bootlog on B1:  http://pastebin.ubuntu.com/23124704/ (sd and hdmi hpd tested)

Based on:
https://git.kernel.org/cgit/linux/kernel/git/tmlind/linux-omap.git/log/?h=omap-for-v4.9/dt
omap-for-v4.9/dt  5c4d9f0d49b0 ARM: dts: dra7: Add missing unit name to memory nodes

Changes listed in context of each of the patches.

Nishanth Menon (2):
  ARM: dts: am57xx-beagle-x15: Remove pinmux configurations for erratum
    i869
  ARM: dts: am57xx-beagle-x15: Add support for rev B1

 arch/arm/boot/dts/Makefile                         |   1 +
 ...eagle-x15.dts => am57xx-beagle-x15-common.dtsi} | 230 +-----
 arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts      |  24 +
 arch/arm/boot/dts/am57xx-beagle-x15.dts            | 812 +--------------------
 4 files changed, 34 insertions(+), 1033 deletions(-)
 copy arch/arm/boot/dts/{am57xx-beagle-x15.dts => am57xx-beagle-x15-common.dtsi} (60%)
 create mode 100644 arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts

-- 
2.9.1.200.gb1ec08f

[PATCH V2 1/2] ARM: dts: am57xx-beagle-x15: Remove pinmux configurations for erratum i869

[Nishanth Menon]

Pinmuxing for DRA7x/AM57x family of processors need to be done in IO
isolation as part of initial bootloader executed from SRAM. This is
done as part of iodelay configuration sequence and is required due
to the limitations introduced by erratum ID: i869[1] (IO Glitches
can occur when changing IO settings) and elaborated in the Technical
Reference Manual[2] 18.4.6.1.7 Isolation Requirements.

Only peripheral that is permitted for dynamic pin mux configuration
is MMC and DCAN. MMC is permitted to change to accommodate the
requirements for varied speeds (which require IO-delay support in
kernel as well). DCAN is a result of i893[1] (DCAN initialization
sequence). However, since we don't use DCAN on X15, with the exception
of MMC, all other pin mux configurations are removed from the dts.

[1] http://www.ti.com/lit/pdf/sprz429
[2] http://www.ti.com/lit/pdf/sprui30

Signed-off-by: Nishanth Menon <nm@ti.com>
---
Changes in v2:
	- renamed $subject to indicate we are not removing *every pinmux*
	- Update in commit message to encompass DCAN as well - for future
	  references as well

v1: https://patchwork.kernel.org/patch/9310615/

 arch/arm/boot/dts/am57xx-beagle-x15.dts | 222 +-------------------------------
 1 file changed, 1 insertion(+), 221 deletions(-)

diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts
index 9067ca092dc5..ef21da558ea3 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts
@@ -59,8 +59,6 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&leds_pins_default>;
 
 		led0 {
 			label = "beagle-x15:usr0";
@@ -116,9 +114,6 @@
 	tpd12s015: encoder {
 		compatible = "ti,tpd12s015";
 
-		pinctrl-names = "default";
-		pinctrl-0 = <&tpd12s015_pins>;
-
 		gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>,	/* gpio7_10, CT CP HPD */
 			<&gpio6 28 GPIO_ACTIVE_HIGH>,	/* gpio6_28, LS OE */
 			<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* gpio7_12/sp1_cs2, HPD */
@@ -173,43 +168,6 @@
 };
 
 &dra7_pmx_core {
-	leds_pins_default: leds_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37a8, PIN_OUTPUT | MUX_MODE14)	/* spi1_d1.gpio7_8 */
-			DRA7XX_CORE_IOPAD(0x37ac, PIN_OUTPUT | MUX_MODE14)	/* spi1_d0.gpio7_9 */
-			DRA7XX_CORE_IOPAD(0x37c0, PIN_OUTPUT | MUX_MODE14)	/* spi2_sclk.gpio7_14 */
-			DRA7XX_CORE_IOPAD(0x37c4, PIN_OUTPUT | MUX_MODE14)	/* spi2_d1.gpio7_15 */
-		>;
-	};
-
-	i2c1_pins_default: i2c1_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda.sda */
-			DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl.scl */
-		>;
-	};
-
-	hdmi_pins: pinmux_hdmi_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1)	/* i2c2_sda.hdmi1_ddc_scl */
-			DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1)	/* i2c2_scl.hdmi1_ddc_sda */
-		>;
-	};
-
-	i2c3_pins_default: i2c3_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x36a4, PIN_INPUT| MUX_MODE10)	/* mcasp1_aclkx.i2c3_sda */
-			DRA7XX_CORE_IOPAD(0x36a8, PIN_INPUT| MUX_MODE10)	/* mcasp1_fsx.i2c3_scl */
-		>;
-	};
-
-	uart3_pins_default: uart3_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */
-			DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */
-		>;
-	};
-
 	mmc1_pins_default: mmc1_pins_default {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14)	/* mmc1sdcd.gpio219 */
@@ -236,154 +194,9 @@
 			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
 		>;
 	};
-
-	cpsw_pins_default: cpsw_pins_default {
-		pinctrl-single,pins = <
-			/* Slave 1 */
-			DRA7XX_CORE_IOPAD(0x3650, PIN_OUTPUT | MUX_MODE0)	/* rgmii1_tclk */
-			DRA7XX_CORE_IOPAD(0x3654, PIN_OUTPUT | MUX_MODE0)	/* rgmii1_tctl */
-			DRA7XX_CORE_IOPAD(0x3658, PIN_OUTPUT | MUX_MODE0)	/* rgmii1_td3 */
-			DRA7XX_CORE_IOPAD(0x365c, PIN_OUTPUT | MUX_MODE0)	/* rgmii1_td2 */
-			DRA7XX_CORE_IOPAD(0x3660, PIN_OUTPUT | MUX_MODE0)	/* rgmii1_td1 */
-			DRA7XX_CORE_IOPAD(0x3664, PIN_OUTPUT | MUX_MODE0)	/* rgmii1_td0 */
-			DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE0)	/* rgmii1_rclk */
-			DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE0)	/* rgmii1_rctl */
-			DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE0)	/* rgmii1_rd3 */
-			DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE0)	/* rgmii1_rd2 */
-			DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE0)	/* rgmii1_rd1 */
-			DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE0)	/* rgmii1_rd0 */
-
-			/* Slave 2 */
-			DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3)	/* rgmii2_tclk */
-			DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3)	/* rgmii2_tctl */
-			DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3)	/* rgmii2_td3 */
-			DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3)	/* rgmii2_td2 */
-			DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3)	/* rgmii2_td1 */
-			DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3)	/* rgmii2_td0 */
-			DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3)	/* rgmii2_rclk */
-			DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3)	/* rgmii2_rctl */
-			DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3)	/* rgmii2_rd3 */
-			DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3)	/* rgmii2_rd2 */
-			DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3)	/* rgmii2_rd1 */
-			DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3)	/* rgmii2_rd0 */
-		>;
-
-	};
-
-	cpsw_pins_sleep: cpsw_pins_sleep {
-		pinctrl-single,pins = <
-			/* Slave 1 */
-			DRA7XX_CORE_IOPAD(0x3650, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3654, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3658, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x365c, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3660, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3664, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE15)
-
-			/* Slave 2 */
-			DRA7XX_CORE_IOPAD(0x3598, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x359c, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a0, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a4, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a8, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35ac, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE15)
-		>;
-	};
-
-	davinci_mdio_pins_default: davinci_mdio_pins_default {
-		pinctrl-single,pins = <
-			/* MDIO */
-			DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0)	/* mdio_mclk */
-			DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0)	/* mdio_d */
-		>;
-	};
-
-	davinci_mdio_pins_sleep: davinci_mdio_pins_sleep {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x363c, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT | MUX_MODE15)
-		>;
-	};
-
-	tps659038_pins_default: tps659038_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3818, PIN_INPUT_PULLUP | MUX_MODE14)	/* wakeup0.gpio1_0 */
-		>;
-	};
-
-	tmp102_pins_default: tmp102_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37c8, PIN_INPUT_PULLUP | MUX_MODE14)	/* spi2_d0.gpio7_16 */
-		>;
-	};
-
-	mcp79410_pins_default: mcp79410_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3824, PIN_INPUT_PULLUP | MUX_MODE1)	/* wakeup3.sys_nirq1 */
-		>;
-	};
-
-	usb1_pins: pinmux_usb1_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
-		>;
-	};
-
-	tpd12s015_pins: pinmux_tpd12s015_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37b0, PIN_OUTPUT | MUX_MODE14)		/* gpio7_10 CT_CP_HPD */
-			DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_PULLDOWN | MUX_MODE14)	/* gpio7_12 HPD */
-			DRA7XX_CORE_IOPAD(0x3770, PIN_OUTPUT | MUX_MODE14)		/* gpio6_28 LS_OE */
-		>;
-	};
-
-	clkout2_pins_default: clkout2_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3694, PIN_OUTPUT_PULLDOWN | MUX_MODE9)	/* xref_clk0.clkout2 */
-		>;
-	};
-
-	clkout2_pins_sleep: clkout2_pins_sleep {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3694, PIN_INPUT | MUX_MODE15)	/* xref_clk0.clkout2 */
-		>;
-	};
-
-	mcasp3_pins_default: mcasp3_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx.mcasp3_aclkx */
-			DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx.mcasp3_fsx */
-			DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0.mcasp3_axr0 */
-			DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1.mcasp3_axr1 */
-		>;
-	};
-
-	mcasp3_pins_sleep: mcasp3_pins_sleep {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT | MUX_MODE15)
-		>;
-	};
 };
-
 &i2c1 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_default>;
 	clock-frequency = <400000>;
 
 	tps659038: tps659038 at 58 {
@@ -392,9 +205,6 @@
 		interrupt-parent = <&gpio1>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 
-		pinctrl-names = "default";
-		pinctrl-0 = <&tps659038_pins_default>;
-
 		#interrupt-cells = <2>;
 		interrupt-controller;
 
@@ -556,8 +366,6 @@
 	tmp102: tmp102 at 48 {
 		compatible = "ti,tmp102";
 		reg = <0x48>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&tmp102_pins_default>;
 		interrupt-parent = <&gpio7>;
 		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
 		#thermal-sensor-cells = <1>;
@@ -567,9 +375,6 @@
 		#sound-dai-cells = <0>;
 		compatible = "ti,tlv320aic3104";
 		reg = <0x18>;
-		pinctrl-names = "default", "sleep";
-		pinctrl-0 = <&clkout2_pins_default>;
-		pinctrl-1 = <&clkout2_pins_sleep>;
 		assigned-clocks = <&clkoutmux2_clk_mux>;
 		assigned-clock-parents = <&sys_clk2_dclk_div>;
 
@@ -590,8 +395,6 @@
 
 &i2c3 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c3_pins_default>;
 	clock-frequency = <400000>;
 
 	mcp_rtc: rtc at 6f {
@@ -601,9 +404,6 @@
 				      <&dra7_pmx_core 0x424>;
 		interrupt-names = "irq", "wakeup";
 
-		pinctrl-names = "default";
-		pinctrl-0 = <&mcp79410_pins_default>;
-
 		vcc-supply = <&vdd_3v3>;
 		wakeup-source;
 	};
@@ -623,16 +423,10 @@
 	status = "okay";
 	interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
 			      <&dra7_pmx_core 0x3f8>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart3_pins_default>;
 };
 
 &mac {
 	status = "okay";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&cpsw_pins_default>;
-	pinctrl-1 = <&cpsw_pins_sleep>;
 	dual_emac;
 };
 
@@ -648,12 +442,6 @@
 	dual_emac_res_vlan = <2>;
 };
 
-&davinci_mdio {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&davinci_mdio_pins_default>;
-	pinctrl-1 = <&davinci_mdio_pins_sleep>;
-};
-
 &mmc1 {
 	status = "okay";
 
@@ -669,7 +457,7 @@
 	status = "okay";
 
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc2_pins_default>;
+	pinctrl-0 = <&mmc1_pins_default>;
 
 	vmmc-supply = <&vdd_3v3>;
 	bus-width = <8>;
@@ -691,8 +479,6 @@
 
 &usb1 {
 	dr_mode = "host";
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb1_pins>;
 };
 
 &omap_dwc3_2 {
@@ -768,9 +554,6 @@
 	status = "ok";
 	vdda-supply = <&ldo4_reg>;
 
-	pinctrl-names = "default";
-	pinctrl-0 = <&hdmi_pins>;
-
 	port {
 		hdmi_out: endpoint {
 			remote-endpoint = <&tpd12s015_in>;
@@ -784,9 +567,6 @@
 
 &mcasp3 {
 	#sound-dai-cells = <0>;
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&mcasp3_pins_default>;
-	pinctrl-1 = <&mcasp3_pins_sleep>;
 	assigned-clocks = <&mcasp3_ahclkx_mux>;
 	assigned-clock-parents = <&sys_clkin2>;
 	status = "okay";
-- 
2.9.1.200.gb1ec08f

[PATCH V2 2/2] ARM: dts: am57xx-beagle-x15: Add support for rev B1

[Nishanth Menon]

Latest update to the BeagleBoard-X15 platform (revision B1)[1] updates
for allowing UHS SD cards to function with the split of supply to SD
card from a dedicated LDO.

As a result of this, AM57xx BeagleBoard-X15 now uses gpio2_30 instead
of gpio6_28 for HDMI because HDMI_LS_OE should now be switched from
GPIO6_28(Y9) to GPIO2_30 (AG8) to avoid a 1.8V GPIO toggling a 3.3V
SoC input when the SD card is in UHS 1.8V mode.

NOTE: For UHS mode to function, we need full fledged IODelay support
in kernel to be functional. IODelay support is yet to be added.

Further, It does not make much sense to spin off a new board
compatible flag since there is no real functional benefit for the
same.

Note: Even though production version is supposed to be B1, there is
over ~200 boards of previous version (A2)[2] out there which continue
to get supported with the existing dts file (to maintain compatibility
with existing bootloaders for A2) and the production board is now
supported as revb1.

[1] https://github.com/beagleboard/beagleboard-x15/blob/master/BEAGLEBOARD_X15_REV_B1.pdf
[2] http://marc.info/?l=linux-arm-kernel&m=147273929820708&w=2

Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
Changes in v2:
	- fixed up commit message to better illustrate why we are insisting on
	  x15.dts to reflect A2 boards.
	- Picked up Tomi's tested-by (no change in HDMI in this patch)
	- Added comment to x15.dts for future reader without needing to dig
	  through git log and figure out this commit..
	- Fixed comment in x15-revb1 for LS OE gpio
	- Fixed up vmmc-supply property for x15.dts

and all the notes since v1 (note that the checkpatch.pl does not like long weblinks
in commit message, I chose to ignore that warning rather than have broken links)

v1: https://patchwork.kernel.org/patch/9310617/

 arch/arm/boot/dts/Makefile                         |   1 +
 ...eagle-x15.dts => am57xx-beagle-x15-common.dtsi} |   8 +-
 arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts      |  24 +
 arch/arm/boot/dts/am57xx-beagle-x15.dts            | 592 +--------------------
 4 files changed, 33 insertions(+), 592 deletions(-)
 copy arch/arm/boot/dts/{am57xx-beagle-x15.dts => am57xx-beagle-x15-common.dtsi} (97%)
 create mode 100644 arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index faacd52370d2..b8d9840895c2 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -570,6 +570,7 @@ dtb-$(CONFIG_SOC_OMAP5) += \
 	omap5-uevm.dtb
 dtb-$(CONFIG_SOC_DRA7XX) += \
 	am57xx-beagle-x15.dtb \
+	am57xx-beagle-x15-revb1.dtb \
 	am57xx-cl-som-am57x.dtb \
 	am57xx-sbc-am57x.dtb \
 	am572x-idk.dtb \
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
similarity index 97%
copy from arch/arm/boot/dts/am57xx-beagle-x15.dts
copy to arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
index ef21da558ea3..ec85ff9004e8 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -13,7 +13,6 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
-	model = "TI AM5728 BeagleBoard-X15";
 	compatible = "ti,am572x-beagle-x15", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7";
 
 	aliases {
@@ -114,10 +113,6 @@
 	tpd12s015: encoder {
 		compatible = "ti,tpd12s015";
 
-		gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>,	/* gpio7_10, CT CP HPD */
-			<&gpio6 28 GPIO_ACTIVE_HIGH>,	/* gpio6_28, LS OE */
-			<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* gpio7_12/sp1_cs2, HPD */
-
 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -448,7 +443,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins_default>;
 
-	vmmc-supply = <&ldo1_reg>;
 	bus-width = <4>;
 	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
 };
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts
new file mode 100644
index 000000000000..ca85570629fd
--- /dev/null
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts
@@ -0,0 +1,24 @@
+/*
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "am57xx-beagle-x15-common.dtsi"
+
+/ {
+	model = "TI AM5728 BeagleBoard-X15 rev B1";
+};
+
+&tpd12s015 {
+	gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>,	/* gpio7_10, CT CP HPD */
+		<&gpio2 30 GPIO_ACTIVE_HIGH>,	/* gpio2_30, LS OE */
+		<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* gpio7_12/sp1_cs2, HPD */
+};
+
+&mmc1 {
+	vmmc-supply = <&vdd_3v3>;
+	vmmc-aux-supply = <&ldo1_reg>;
+};
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts
index ef21da558ea3..8c66f2efd283 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts
@@ -1,602 +1,24 @@
 /*
- * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-/dts-v1/;
 
-#include "dra74x.dtsi"
-#include "am57xx-commercial-grade.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/irq.h>
+#include "am57xx-beagle-x15-common.dtsi"
 
 / {
+	/* NOTE: This describes the "original" pre-production A2 revision */
 	model = "TI AM5728 BeagleBoard-X15";
-	compatible = "ti,am572x-beagle-x15", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7";
-
-	aliases {
-		rtc0 = &mcp_rtc;
-		rtc1 = &tps659038_rtc;
-		rtc2 = &rtc;
-		display0 = &hdmi0;
-	};
-
-	memory at 0 {
-		device_type = "memory";
-		reg = <0x0 0x80000000 0x0 0x80000000>;
-	};
-
-	vdd_3v3: fixedregulator-vdd_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd_3v3";
-		vin-supply = <&regen1>;
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	aic_dvdd: fixedregulator-aic_dvdd {
-		compatible = "regulator-fixed";
-		regulator-name = "aic_dvdd_fixed";
-		vin-supply = <&vdd_3v3>;
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-	};
-
-	vtt_fixed: fixedregulator-vtt {
-		/* TPS51200 */
-		compatible = "regulator-fixed";
-		regulator-name = "vtt_fixed";
-		vin-supply = <&smps3_reg>;
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-		regulator-boot-on;
-		enable-active-high;
-		gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led0 {
-			label = "beagle-x15:usr0";
-			gpios = <&gpio7 9 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
-		};
-
-		led1 {
-			label = "beagle-x15:usr1";
-			gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "cpu0";
-			default-state = "off";
-		};
-
-		led2 {
-			label = "beagle-x15:usr2";
-			gpios = <&gpio7 14 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-			default-state = "off";
-		};
-
-		led3 {
-			label = "beagle-x15:usr3";
-			gpios = <&gpio7 15 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "disk-activity";
-			default-state = "off";
-		};
-	};
-
-	gpio_fan: gpio_fan {
-		/* Based on 5v 500mA AFB02505HHB */
-		compatible = "gpio-fan";
-		gpios =  <&tps659038_gpio 2 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <0     0>,
-				     <13000 1>;
-		#cooling-cells = <2>;
-	};
-
-	hdmi0: connector {
-		compatible = "hdmi-connector";
-		label = "hdmi";
-
-		type = "a";
-
-		port {
-			hdmi_connector_in: endpoint {
-				remote-endpoint = <&tpd12s015_out>;
-			};
-		};
-	};
-
-	tpd12s015: encoder {
-		compatible = "ti,tpd12s015";
-
-		gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>,	/* gpio7_10, CT CP HPD */
-			<&gpio6 28 GPIO_ACTIVE_HIGH>,	/* gpio6_28, LS OE */
-			<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* gpio7_12/sp1_cs2, HPD */
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port at 0 {
-				reg = <0>;
-
-				tpd12s015_in: endpoint {
-					remote-endpoint = <&hdmi_out>;
-				};
-			};
-
-			port at 1 {
-				reg = <1>;
-
-				tpd12s015_out: endpoint {
-					remote-endpoint = <&hdmi_connector_in>;
-				};
-			};
-		};
-	};
-
-	sound0: sound0 {
-		compatible = "simple-audio-card";
-		simple-audio-card,name = "BeagleBoard-X15";
-		simple-audio-card,widgets =
-			"Line", "Line Out",
-			"Line", "Line In";
-		simple-audio-card,routing =
-			"Line Out",	"LLOUT",
-			"Line Out",	"RLOUT",
-			"MIC2L",	"Line In",
-			"MIC2R",	"Line In";
-		simple-audio-card,format = "dsp_b";
-		simple-audio-card,bitclock-master = <&sound0_master>;
-		simple-audio-card,frame-master = <&sound0_master>;
-		simple-audio-card,bitclock-inversion;
-
-		simple-audio-card,cpu {
-			sound-dai = <&mcasp3>;
-		};
-
-		sound0_master: simple-audio-card,codec {
-			sound-dai = <&tlv320aic3104>;
-			clocks = <&clkout2_clk>;
-		};
-	};
-};
-
-&dra7_pmx_core {
-	mmc1_pins_default: mmc1_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14)	/* mmc1sdcd.gpio219 */
-			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
-			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
-			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
-			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
-			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
-			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
-		>;
-	};
-
-	mmc2_pins_default: mmc2_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
-			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
-			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
-			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
-			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
-			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
-			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
-			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
-			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
-			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
-		>;
-	};
-};
-&i2c1 {
-	status = "okay";
-	clock-frequency = <400000>;
-
-	tps659038: tps659038 at 58 {
-		compatible = "ti,tps659038";
-		reg = <0x58>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-
-		#interrupt-cells = <2>;
-		interrupt-controller;
-
-		ti,system-power-controller;
-
-		tps659038_pmic {
-			compatible = "ti,tps659038-pmic";
-
-			regulators {
-				smps12_reg: smps12 {
-					/* VDD_MPU */
-					regulator-name = "smps12";
-					regulator-min-microvolt = < 850000>;
-					regulator-max-microvolt = <1250000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps3_reg: smps3 {
-					/* VDD_DDR */
-					regulator-name = "smps3";
-					regulator-min-microvolt = <1350000>;
-					regulator-max-microvolt = <1350000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps45_reg: smps45 {
-					/* VDD_DSPEVE, VDD_IVA, VDD_GPU */
-					regulator-name = "smps45";
-					regulator-min-microvolt = < 850000>;
-					regulator-max-microvolt = <1250000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps6_reg: smps6 {
-					/* VDD_CORE */
-					regulator-name = "smps6";
-					regulator-min-microvolt = <850000>;
-					regulator-max-microvolt = <1150000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				/* SMPS7 unused */
-
-				smps8_reg: smps8 {
-					/* VDD_1V8 */
-					regulator-name = "smps8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				/* SMPS9 unused */
-
-				ldo1_reg: ldo1 {
-					/* VDD_SD / VDDSHV8  */
-					regulator-name = "ldo1";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-boot-on;
-					regulator-always-on;
-				};
-
-				ldo2_reg: ldo2 {
-					/* VDD_SHV5 */
-					regulator-name = "ldo2";
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldo3_reg: ldo3 {
-					/* VDDA_1V8_PHYA */
-					regulator-name = "ldo3";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldo4_reg: ldo4 {
-					/* VDDA_1V8_PHYB */
-					regulator-name = "ldo4";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldo9_reg: ldo9 {
-					/* VDD_RTC */
-					regulator-name = "ldo9";
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldoln_reg: ldoln {
-					/* VDDA_1V8_PLL */
-					regulator-name = "ldoln";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldousb_reg: ldousb {
-					/* VDDA_3V_USB: VDDA_USBHS33 */
-					regulator-name = "ldousb";
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-boot-on;
-				};
-
-				regen1: regen1 {
-					/* VDD_3V3_ON */
-					regulator-name = "regen1";
-					regulator-boot-on;
-					regulator-always-on;
-				};
-			};
-		};
-
-		tps659038_rtc: tps659038_rtc {
-			compatible = "ti,palmas-rtc";
-			interrupt-parent = <&tps659038>;
-			interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
-			wakeup-source;
-		};
-
-		tps659038_pwr_button: tps659038_pwr_button {
-			compatible = "ti,palmas-pwrbutton";
-			interrupt-parent = <&tps659038>;
-			interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
-			wakeup-source;
-			ti,palmas-long-press-seconds = <12>;
-		};
-
-		tps659038_gpio: tps659038_gpio {
-			compatible = "ti,palmas-gpio";
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-
-		extcon_usb2: tps659038_usb {
-			compatible = "ti,palmas-usb-vid";
-			ti,enable-vbus-detection;
-			vbus-gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
-		};
-
-	};
-
-	tmp102: tmp102 at 48 {
-		compatible = "ti,tmp102";
-		reg = <0x48>;
-		interrupt-parent = <&gpio7>;
-		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
-		#thermal-sensor-cells = <1>;
-	};
-
-	tlv320aic3104: tlv320aic3104 at 18 {
-		#sound-dai-cells = <0>;
-		compatible = "ti,tlv320aic3104";
-		reg = <0x18>;
-		assigned-clocks = <&clkoutmux2_clk_mux>;
-		assigned-clock-parents = <&sys_clk2_dclk_div>;
-
-		status = "okay";
-		adc-settle-ms = <40>;
-
-		AVDD-supply = <&vdd_3v3>;
-		IOVDD-supply = <&vdd_3v3>;
-		DRVDD-supply = <&vdd_3v3>;
-		DVDD-supply = <&aic_dvdd>;
-	};
-
-	eeprom: eeprom at 50 {
-		compatible = "at,24c32";
-		reg = <0x50>;
-	};
 };
 
-&i2c3 {
-	status = "okay";
-	clock-frequency = <400000>;
-
-	mcp_rtc: rtc at 6f {
-		compatible = "microchip,mcp7941x";
-		reg = <0x6f>;
-		interrupts-extended = <&crossbar_mpu GIC_SPI 2 IRQ_TYPE_EDGE_RISING>,
-				      <&dra7_pmx_core 0x424>;
-		interrupt-names = "irq", "wakeup";
-
-		vcc-supply = <&vdd_3v3>;
-		wakeup-source;
-	};
-};
-
-&gpio7 {
-	ti,no-reset-on-init;
-	ti,no-idle-on-init;
-};
-
-&cpu0 {
-	cpu0-supply = <&smps12_reg>;
-	voltage-tolerance = <1>;
-};
-
-&uart3 {
-	status = "okay";
-	interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
-			      <&dra7_pmx_core 0x3f8>;
-};
-
-&mac {
-	status = "okay";
-	dual_emac;
-};
-
-&cpsw_emac0 {
-	phy_id = <&davinci_mdio>, <1>;
-	phy-mode = "rgmii";
-	dual_emac_res_vlan = <1>;
-};
-
-&cpsw_emac1 {
-	phy_id = <&davinci_mdio>, <2>;
-	phy-mode = "rgmii";
-	dual_emac_res_vlan = <2>;
+&tpd12s015 {
+	gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>,	/* gpio7_10, CT CP HPD */
+		<&gpio6 28 GPIO_ACTIVE_HIGH>,	/* gpio6_28, LS OE */
+		<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* gpio7_12/sp1_cs2, HPD */
 };
 
 &mmc1 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_default>;
-
 	vmmc-supply = <&ldo1_reg>;
-	bus-width = <4>;
-	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
-};
-
-&mmc2 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_default>;
-
-	vmmc-supply = <&vdd_3v3>;
-	bus-width = <8>;
-	ti,non-removable;
-	cap-mmc-dual-data-rate;
-};
-
-&sata {
-	status = "okay";
-};
-
-&usb2_phy1 {
-	phy-supply = <&ldousb_reg>;
-};
-
-&usb2_phy2 {
-	phy-supply = <&ldousb_reg>;
-};
-
-&usb1 {
-	dr_mode = "host";
-};
-
-&omap_dwc3_2 {
-	extcon = <&extcon_usb2>;
-};
-
-&usb2 {
-	/*
-	 * Stand alone usage is peripheral only.
-	 * However, with some resistor modifications
-	 * this port can be used via expansion connectors
-	 * as "host" or "dual-role". If so, provide
-	 * the necessary dr_mode override in the expansion
-	 * board's DT.
-	 */
-	dr_mode = "peripheral";
-};
-
-&cpu_trips {
-	cpu_alert1: cpu_alert1 {
-		temperature = <50000>; /* millicelsius */
-		hysteresis = <2000>; /* millicelsius */
-		type = "active";
-	};
-};
-
-&cpu_cooling_maps {
-	map1 {
-		trip = <&cpu_alert1>;
-		cooling-device = <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-	};
-};
-
-&thermal_zones {
-	board_thermal: board_thermal {
-		polling-delay-passive = <1250>; /* milliseconds */
-		polling-delay = <1500>; /* milliseconds */
-
-				/* sensor       ID */
-		thermal-sensors = <&tmp102     0>;
-
-		board_trips: trips {
-			board_alert0: board_alert {
-				temperature = <40000>; /* millicelsius */
-				hysteresis = <2000>; /* millicelsius */
-				type = "active";
-			};
-
-			board_crit: board_crit {
-				temperature = <105000>; /* millicelsius */
-				hysteresis = <0>; /* millicelsius */
-				type = "critical";
-			};
-		};
-
-		board_cooling_maps: cooling-maps {
-			map0 {
-				trip = <&board_alert0>;
-				cooling-device =
-				  <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-			};
-		};
-       };
-};
-
-&dss {
-	status = "ok";
-
-	vdda_video-supply = <&ldoln_reg>;
-};
-
-&hdmi {
-	status = "ok";
-	vdda-supply = <&ldo4_reg>;
-
-	port {
-		hdmi_out: endpoint {
-			remote-endpoint = <&tpd12s015_in>;
-		};
-	};
-};
-
-&pcie1 {
-	gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
-};
-
-&mcasp3 {
-	#sound-dai-cells = <0>;
-	assigned-clocks = <&mcasp3_ahclkx_mux>;
-	assigned-clock-parents = <&sys_clkin2>;
-	status = "okay";
-
-	op-mode = <0>;	/* MCASP_IIS_MODE */
-	tdm-slots = <2>;
-	/* 4 serializers */
-	serial-dir = <	/* 0: INACTIVE, 1: TX, 2: RX */
-		1 2 0 0
-	>;
-	tx-num-evt = <32>;
-	rx-num-evt = <32>;
-};
-
-&mailbox5 {
-	status = "okay";
-	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
-		status = "okay";
-	};
-	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
-		status = "okay";
-	};
-};
-
-&mailbox6 {
-	status = "okay";
-	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
-		status = "okay";
-	};
-	mbox_dsp2_ipc3x: mbox_dsp2_ipc3x {
-		status = "okay";
-	};
 };
-- 
2.9.1.200.gb1ec08f

[PATCH V2 0/2] ARM: dts: Introduce support for rev BeagleBoard-X15 B1

[Tony Lindgren]

* Nishanth Menon <nm@ti.com> [160902 10:14]:
> Hi,
> 
> Please find the series to cleanup and support Production version of
> Beagleboard-X15 rev B1 support.

Applying into omap-for-v4.9/dt thanks.

Tony