[linux-sunxi][PATCH] ARM: dts: sun8i-h3: Add dts for the Beelink X2 STB

* [linux-sunxi][PATCH] ARM: dts: sun8i-h3: Add dts for the Beelink X2 STB
@ 2017-01-12 17:11 codekipper at gmail.com
  2017-01-12 17:28 ` Maxime Ripard
  0 siblings, 1 reply; 3+ messages in thread
From: codekipper at gmail.com @ 2017-01-12 17:11 UTC (permalink / raw)
  To: linux-arm-kernel

From: Marcus Cooper <codekipper@gmail.com>

The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, HDMI, an IR
receiver, 1 LEDs and an optical S/PDIF connector.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
---
 arch/arm/boot/dts/Makefile                |   1 +
 arch/arm/boot/dts/sun8i-h3-beelink-x2.dts | 187 ++++++++++++++++++++++++++++++
 2 files changed, 188 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun8i-h3-beelink-x2.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 78a94b747059..75960b1468a4 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -857,6 +857,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-a83t-cubietruck-plus.dtb \
 	sun8i-h2-plus-orangepi-zero.dtb \
 	sun8i-h3-bananapi-m2-plus.dtb \
+	sun8i-h3-beelink-x2.dtb \
 	sun8i-h3-nanopi-m1.dtb	\
 	sun8i-h3-nanopi-neo.dtb \
 	sun8i-h3-orangepi-2.dtb \
diff --git a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
new file mode 100644
index 000000000000..bc5aed52cb1d
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
@@ -0,0 +1,187 @@
+/*
+ * Copyright (C) 2017 Marcus Cooper <codekipper@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	model = "Beelink X2";
+	compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
+
+	aliases {
+		serial0 = &uart0;
+		/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+		ethernet1 = &rtl8189ftv;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwr_led_x2>;
+
+		pwr_led {
+			label = "beelink-x2:red:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+			default-state = "on";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&sw_r_x2>;
+
+		sw4 {
+			label = "power";
+			linux,code = <BTN_0>;
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_en_x2>;
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+	};
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir_pins_a>;
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	cd-inverted;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_a>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	/*
+	 * Explicitly define the sdio device, so that we can add an ethernet
+	 * alias for it (which e.g. makes u-boot set a mac-address).
+	 */
+	rtl8189ftv: sdio_wifi at 1 {
+		reg = <1>;
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&mmc2_8bit_pins {
+	/* Increase drive strength for DDR modes */
+	drive-strength = <40>;
+	/* eMMC is missing pull-ups */
+	bias-pull-up;
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&r_pio {
+	pwr_led_x2: led_pins at 0 {
+		pins = "PL10";
+		function = "gpio_out";
+	};
+
+	sw_r_x2: key_pins at 0 {
+		pins = "PL3";
+		function = "gpio_in";
+	};
+
+	wifi_en_x2: wifi_en_pin {
+		pins = "PL7";
+		function = "gpio_out";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	status = "okay";
+};
+
+&usbphy {
+	/* USB VBUS is on as long as VCC-IO is on */
+	status = "okay";
+};
-- 
2.11.0

^ permalink raw reply related	[flat|nested] 3+ messages in thread