* [PATCH] ARM: dts: BCM5301X: Specify MDIO bus in the DT @ 2017-04-02 21:08 Rafał Miłecki 2017-04-02 21:14 ` Florian Fainelli 2017-04-19 21:54 ` [PATCH V2] " Rafał Miłecki 0 siblings, 2 replies; 9+ messages in thread From: Rafał Miłecki @ 2017-04-02 21:08 UTC (permalink / raw) To: linux-arm-kernel From: Rafa? Mi?ecki <rafal@milecki.pl> Northstar devices have MDIO bus that may contain various PHYs attached. A common example is USB 3.0 PHY (that doesn't have an MDIO driver yet). Signed-off-by: Rafa? Mi?ecki <rafal@milecki.pl> --- arch/arm/boot/dts/bcm5301x.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi index acee36a61004..6a2afe7880ae 100644 --- a/arch/arm/boot/dts/bcm5301x.dtsi +++ b/arch/arm/boot/dts/bcm5301x.dtsi @@ -320,6 +320,13 @@ }; }; + mdio at 18003000 { + compatible = "brcm,iproc-mdio"; + reg = <0x18003000 0x8>; + #size-cells = <1>; + #address-cells = <0>; + }; + i2c0: i2c at 18009000 { compatible = "brcm,iproc-i2c"; reg = <0x18009000 0x50>; -- 2.11.0 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH] ARM: dts: BCM5301X: Specify MDIO bus in the DT 2017-04-02 21:08 [PATCH] ARM: dts: BCM5301X: Specify MDIO bus in the DT Rafał Miłecki @ 2017-04-02 21:14 ` Florian Fainelli 2017-04-02 21:25 ` Rafał Miłecki 2017-04-19 21:54 ` [PATCH V2] " Rafał Miłecki 1 sibling, 1 reply; 9+ messages in thread From: Florian Fainelli @ 2017-04-02 21:14 UTC (permalink / raw) To: linux-arm-kernel Le 04/02/17 ? 14:08, Rafa? Mi?ecki a ?crit : > From: Rafa? Mi?ecki <rafal@milecki.pl> > > Northstar devices have MDIO bus that may contain various PHYs attached. > A common example is USB 3.0 PHY (that doesn't have an MDIO driver yet). > > Signed-off-by: Rafa? Mi?ecki <rafal@milecki.pl> > --- > arch/arm/boot/dts/bcm5301x.dtsi | 7 +++++++ > 1 file changed, 7 insertions(+) > > diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi > index acee36a61004..6a2afe7880ae 100644 > --- a/arch/arm/boot/dts/bcm5301x.dtsi > +++ b/arch/arm/boot/dts/bcm5301x.dtsi > @@ -320,6 +320,13 @@ > }; > }; > > + mdio at 18003000 { > + compatible = "brcm,iproc-mdio"; > + reg = <0x18003000 0x8>; > + #size-cells = <1>; > + #address-cells = <0>; > + }; This looks fine, but usually the block should be enabled on a per-board basis, such that there should be a status = "disabled" property here by default. -- Florian ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] ARM: dts: BCM5301X: Specify MDIO bus in the DT 2017-04-02 21:14 ` Florian Fainelli @ 2017-04-02 21:25 ` Rafał Miłecki 2017-04-19 16:43 ` Florian Fainelli 0 siblings, 1 reply; 9+ messages in thread From: Rafał Miłecki @ 2017-04-02 21:25 UTC (permalink / raw) To: linux-arm-kernel On 04/02/2017 11:14 PM, Florian Fainelli wrote: > Le 04/02/17 ? 14:08, Rafa? Mi?ecki a ?crit : >> From: Rafa? Mi?ecki <rafal@milecki.pl> >> >> Northstar devices have MDIO bus that may contain various PHYs attached. >> A common example is USB 3.0 PHY (that doesn't have an MDIO driver yet). >> >> Signed-off-by: Rafa? Mi?ecki <rafal@milecki.pl> >> --- >> arch/arm/boot/dts/bcm5301x.dtsi | 7 +++++++ >> 1 file changed, 7 insertions(+) >> >> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi >> index acee36a61004..6a2afe7880ae 100644 >> --- a/arch/arm/boot/dts/bcm5301x.dtsi >> +++ b/arch/arm/boot/dts/bcm5301x.dtsi >> @@ -320,6 +320,13 @@ >> }; >> }; >> >> + mdio at 18003000 { >> + compatible = "brcm,iproc-mdio"; >> + reg = <0x18003000 0x8>; >> + #size-cells = <1>; >> + #address-cells = <0>; >> + }; > > This looks fine, but usually the block should be enabled on a per-board > basis, such that there should be a status = "disabled" property here by > default. I think we have few blocks in bcm5301x.dtsi enabled by default. I guess it's for stuff that is always present on every SoC family board: rng, nand, spi to name few. It makes some sense, consider e.g. spi. Every Northstar board has SPI controller so it's enabled by default. Not every board has SPI flash, so it's disabled by default. It's there and it make sense to me. Is that OK or not? I find MDIO situation quite simiar. It seems every Northstar board has MDIO bus just devices may differ and should not be enabled by default. ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] ARM: dts: BCM5301X: Specify MDIO bus in the DT 2017-04-02 21:25 ` Rafał Miłecki @ 2017-04-19 16:43 ` Florian Fainelli 2017-04-19 17:35 ` Rafał Miłecki 0 siblings, 1 reply; 9+ messages in thread From: Florian Fainelli @ 2017-04-19 16:43 UTC (permalink / raw) To: linux-arm-kernel On 04/02/2017 02:25 PM, Rafa? Mi?ecki wrote: > On 04/02/2017 11:14 PM, Florian Fainelli wrote: >> Le 04/02/17 ? 14:08, Rafa? Mi?ecki a ?crit : >>> From: Rafa? Mi?ecki <rafal@milecki.pl> >>> >>> Northstar devices have MDIO bus that may contain various PHYs attached. >>> A common example is USB 3.0 PHY (that doesn't have an MDIO driver yet). >>> >>> Signed-off-by: Rafa? Mi?ecki <rafal@milecki.pl> >>> --- >>> arch/arm/boot/dts/bcm5301x.dtsi | 7 +++++++ >>> 1 file changed, 7 insertions(+) >>> >>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi >>> b/arch/arm/boot/dts/bcm5301x.dtsi >>> index acee36a61004..6a2afe7880ae 100644 >>> --- a/arch/arm/boot/dts/bcm5301x.dtsi >>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi >>> @@ -320,6 +320,13 @@ >>> }; >>> }; >>> >>> + mdio at 18003000 { >>> + compatible = "brcm,iproc-mdio"; >>> + reg = <0x18003000 0x8>; >>> + #size-cells = <1>; >>> + #address-cells = <0>; >>> + }; >> >> This looks fine, but usually the block should be enabled on a per-board >> basis, such that there should be a status = "disabled" property here by >> default. > > I think we have few blocks in bcm5301x.dtsi enabled by default. I guess > it's > for stuff that is always present on every SoC family board: rng, nand, > spi to > name few. > > It makes some sense, consider e.g. spi. Every Northstar board has SPI > controller so it's enabled by default. Not every board has SPI flash, so > it's > disabled by default. > > It's there and it make sense to me. Is that OK or not? Even though there are devices that are always enabled on a given SoC, because the board designs are always consistent does not necessarily make them good candidates to be enabled at the .dtsi level. This is particularly true when there are external connections to blocks (SPI, NAND, USB, Ethernet, MDIO to name a few), having them disabled by default is safer as a starting point to begin with. > > I find MDIO situation quite simiar. It seems every Northstar board has > MDIO bus > just devices may differ and should not be enabled by default. In which case, the only difference, for you would be to do to, at the board-level DTS: &mdio { status = "okay"; phy at 0 { reg = <0>; ... }; }; versus: &mdio { phy at 0 { reg = <0>; ... }; }; I think we can afford putting the mdio node's status property in each board-level DTS and make it clear that way that it is enabled because there are child nodes enabled? NB: with a CONFIG_OF system, there is no automatic probing of MDIO child devices because it relies on child nodes being declared, but you would still get the driver to be probed and enabled, which is a waste of resources at best. Thanks -- Florian ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] ARM: dts: BCM5301X: Specify MDIO bus in the DT 2017-04-19 16:43 ` Florian Fainelli @ 2017-04-19 17:35 ` Rafał Miłecki 2017-04-19 17:52 ` Florian Fainelli 0 siblings, 1 reply; 9+ messages in thread From: Rafał Miłecki @ 2017-04-19 17:35 UTC (permalink / raw) To: linux-arm-kernel On 04/19/2017 06:43 PM, Florian Fainelli wrote: > On 04/02/2017 02:25 PM, Rafa? Mi?ecki wrote: >> On 04/02/2017 11:14 PM, Florian Fainelli wrote: >>> Le 04/02/17 ? 14:08, Rafa? Mi?ecki a ?crit : >>>> From: Rafa? Mi?ecki <rafal@milecki.pl> >>>> >>>> Northstar devices have MDIO bus that may contain various PHYs attached. >>>> A common example is USB 3.0 PHY (that doesn't have an MDIO driver yet). >>>> >>>> Signed-off-by: Rafa? Mi?ecki <rafal@milecki.pl> >>>> --- >>>> arch/arm/boot/dts/bcm5301x.dtsi | 7 +++++++ >>>> 1 file changed, 7 insertions(+) >>>> >>>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi >>>> b/arch/arm/boot/dts/bcm5301x.dtsi >>>> index acee36a61004..6a2afe7880ae 100644 >>>> --- a/arch/arm/boot/dts/bcm5301x.dtsi >>>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi >>>> @@ -320,6 +320,13 @@ >>>> }; >>>> }; >>>> >>>> + mdio at 18003000 { >>>> + compatible = "brcm,iproc-mdio"; >>>> + reg = <0x18003000 0x8>; >>>> + #size-cells = <1>; >>>> + #address-cells = <0>; >>>> + }; >>> >>> This looks fine, but usually the block should be enabled on a per-board >>> basis, such that there should be a status = "disabled" property here by >>> default. >> >> I think we have few blocks in bcm5301x.dtsi enabled by default. I guess >> it's >> for stuff that is always present on every SoC family board: rng, nand, >> spi to >> name few. >> >> It makes some sense, consider e.g. spi. Every Northstar board has SPI >> controller so it's enabled by default. Not every board has SPI flash, so >> it's >> disabled by default. >> >> It's there and it make sense to me. Is that OK or not? > > Even though there are devices that are always enabled on a given SoC, > because the board designs are always consistent does not necessarily > make them good candidates to be enabled at the .dtsi level. This is > particularly true when there are external connections to blocks (SPI, > NAND, USB, Ethernet, MDIO to name a few), having them disabled by > default is safer as a starting point to begin with. In case of Northstar there is USB 3.0 PHY connected *internally* to this MDIO. I don't think any board manufacturer is able to rip SoC out of the MDIO or the USB 3.0 PHY. >> I find MDIO situation quite simiar. It seems every Northstar board has >> MDIO bus >> just devices may differ and should not be enabled by default. > > In which case, the only difference, for you would be to do to, at the > board-level DTS: > > &mdio { > status = "okay"; > > phy at 0 { > reg = <0>; > ... > }; > }; > > versus: > > &mdio { > phy at 0 { > reg = <0>; > ... > }; > }; > > I think we can afford putting the mdio node's status property in each > board-level DTS and make it clear that way that it is enabled because > there are child nodes enabled? This will be a pretty big effort because every Northstar device I know has USB 3.0 PHY in the SoC. > NB: with a CONFIG_OF system, there is no automatic probing of MDIO child > devices because it relies on child nodes being declared, but you would > still get the driver to be probed and enabled, which is a waste of > resources at best. Right, but DT role is to describe device/board and not really care if operating system handles that efficiently. ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] ARM: dts: BCM5301X: Specify MDIO bus in the DT 2017-04-19 17:35 ` Rafał Miłecki @ 2017-04-19 17:52 ` Florian Fainelli 2017-04-19 18:10 ` Rafał Miłecki 0 siblings, 1 reply; 9+ messages in thread From: Florian Fainelli @ 2017-04-19 17:52 UTC (permalink / raw) To: linux-arm-kernel On 04/19/2017 10:35 AM, Rafa? Mi?ecki wrote: > On 04/19/2017 06:43 PM, Florian Fainelli wrote: >> On 04/02/2017 02:25 PM, Rafa? Mi?ecki wrote: >>> On 04/02/2017 11:14 PM, Florian Fainelli wrote: >>>> Le 04/02/17 ? 14:08, Rafa? Mi?ecki a ?crit : >>>>> From: Rafa? Mi?ecki <rafal@milecki.pl> >>>>> >>>>> Northstar devices have MDIO bus that may contain various PHYs >>>>> attached. >>>>> A common example is USB 3.0 PHY (that doesn't have an MDIO driver >>>>> yet). >>>>> >>>>> Signed-off-by: Rafa? Mi?ecki <rafal@milecki.pl> >>>>> --- >>>>> arch/arm/boot/dts/bcm5301x.dtsi | 7 +++++++ >>>>> 1 file changed, 7 insertions(+) >>>>> >>>>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi >>>>> b/arch/arm/boot/dts/bcm5301x.dtsi >>>>> index acee36a61004..6a2afe7880ae 100644 >>>>> --- a/arch/arm/boot/dts/bcm5301x.dtsi >>>>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi >>>>> @@ -320,6 +320,13 @@ >>>>> }; >>>>> }; >>>>> >>>>> + mdio at 18003000 { >>>>> + compatible = "brcm,iproc-mdio"; >>>>> + reg = <0x18003000 0x8>; >>>>> + #size-cells = <1>; >>>>> + #address-cells = <0>; >>>>> + }; >>>> >>>> This looks fine, but usually the block should be enabled on a per-board >>>> basis, such that there should be a status = "disabled" property here by >>>> default. >>> >>> I think we have few blocks in bcm5301x.dtsi enabled by default. I guess >>> it's >>> for stuff that is always present on every SoC family board: rng, nand, >>> spi to >>> name few. >>> >>> It makes some sense, consider e.g. spi. Every Northstar board has SPI >>> controller so it's enabled by default. Not every board has SPI flash, so >>> it's >>> disabled by default. >>> >>> It's there and it make sense to me. Is that OK or not? >> >> Even though there are devices that are always enabled on a given SoC, >> because the board designs are always consistent does not necessarily >> make them good candidates to be enabled at the .dtsi level. This is >> particularly true when there are external connections to blocks (SPI, >> NAND, USB, Ethernet, MDIO to name a few), having them disabled by >> default is safer as a starting point to begin with. > > In case of Northstar there is USB 3.0 PHY connected *internally* to this > MDIO. > I don't think any board manufacturer is able to rip SoC out of the MDIO > or the > USB 3.0 PHY. OK, then can you still resubmit a proper patch that a) puts that information in the commit message, and b) also adds a proper label to the mdio node such that it can later on be referenced by label in board-level DTS files? By that I mean: mdio: mdio at 18003000 { Thank you > > >>> I find MDIO situation quite simiar. It seems every Northstar board has >>> MDIO bus >>> just devices may differ and should not be enabled by default. >> >> In which case, the only difference, for you would be to do to, at the >> board-level DTS: >> >> &mdio { >> status = "okay"; >> >> phy at 0 { >> reg = <0>; >> ... >> }; >> }; >> >> versus: >> >> &mdio { >> phy at 0 { >> reg = <0>; >> ... >> }; >> }; >> >> I think we can afford putting the mdio node's status property in each >> board-level DTS and make it clear that way that it is enabled because >> there are child nodes enabled? > > This will be a pretty big effort because every Northstar device I know > has USB > 3.0 PHY in the SoC. Adding a one liner is a "pretty big effort", for sure. > > >> NB: with a CONFIG_OF system, there is no automatic probing of MDIO child >> devices because it relies on child nodes being declared, but you would >> still get the driver to be probed and enabled, which is a waste of >> resources at best. > > Right, but DT role is to describe device/board and not really care if > operating > system handles that efficiently. -- Florian ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] ARM: dts: BCM5301X: Specify MDIO bus in the DT 2017-04-19 17:52 ` Florian Fainelli @ 2017-04-19 18:10 ` Rafał Miłecki 2017-04-19 18:13 ` Florian Fainelli 0 siblings, 1 reply; 9+ messages in thread From: Rafał Miłecki @ 2017-04-19 18:10 UTC (permalink / raw) To: linux-arm-kernel On 04/19/2017 07:52 PM, Florian Fainelli wrote: > On 04/19/2017 10:35 AM, Rafa? Mi?ecki wrote: >> On 04/19/2017 06:43 PM, Florian Fainelli wrote: >>> On 04/02/2017 02:25 PM, Rafa? Mi?ecki wrote: >>>> On 04/02/2017 11:14 PM, Florian Fainelli wrote: >>>>> Le 04/02/17 ? 14:08, Rafa? Mi?ecki a ?crit : >>>>>> From: Rafa? Mi?ecki <rafal@milecki.pl> >>>>>> >>>>>> Northstar devices have MDIO bus that may contain various PHYs >>>>>> attached. >>>>>> A common example is USB 3.0 PHY (that doesn't have an MDIO driver >>>>>> yet). >>>>>> >>>>>> Signed-off-by: Rafa? Mi?ecki <rafal@milecki.pl> >>>>>> --- >>>>>> arch/arm/boot/dts/bcm5301x.dtsi | 7 +++++++ >>>>>> 1 file changed, 7 insertions(+) >>>>>> >>>>>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi >>>>>> b/arch/arm/boot/dts/bcm5301x.dtsi >>>>>> index acee36a61004..6a2afe7880ae 100644 >>>>>> --- a/arch/arm/boot/dts/bcm5301x.dtsi >>>>>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi >>>>>> @@ -320,6 +320,13 @@ >>>>>> }; >>>>>> }; >>>>>> >>>>>> + mdio at 18003000 { >>>>>> + compatible = "brcm,iproc-mdio"; >>>>>> + reg = <0x18003000 0x8>; >>>>>> + #size-cells = <1>; >>>>>> + #address-cells = <0>; >>>>>> + }; >>>>> >>>>> This looks fine, but usually the block should be enabled on a per-board >>>>> basis, such that there should be a status = "disabled" property here by >>>>> default. >>>> >>>> I think we have few blocks in bcm5301x.dtsi enabled by default. I guess >>>> it's >>>> for stuff that is always present on every SoC family board: rng, nand, >>>> spi to >>>> name few. >>>> >>>> It makes some sense, consider e.g. spi. Every Northstar board has SPI >>>> controller so it's enabled by default. Not every board has SPI flash, so >>>> it's >>>> disabled by default. >>>> >>>> It's there and it make sense to me. Is that OK or not? >>> >>> Even though there are devices that are always enabled on a given SoC, >>> because the board designs are always consistent does not necessarily >>> make them good candidates to be enabled at the .dtsi level. This is >>> particularly true when there are external connections to blocks (SPI, >>> NAND, USB, Ethernet, MDIO to name a few), having them disabled by >>> default is safer as a starting point to begin with. >> >> In case of Northstar there is USB 3.0 PHY connected *internally* to this >> MDIO. >> I don't think any board manufacturer is able to rip SoC out of the MDIO >> or the >> USB 3.0 PHY. > > OK, then can you still resubmit a proper patch that a) puts that > information in the commit message, and b) also adds a proper label to > the mdio node such that it can later on be referenced by label in > board-level DTS files? By that I mean: > > mdio: mdio at 18003000 { > > Thank you > >> >> >>>> I find MDIO situation quite simiar. It seems every Northstar board has >>>> MDIO bus >>>> just devices may differ and should not be enabled by default. >>> >>> In which case, the only difference, for you would be to do to, at the >>> board-level DTS: >>> >>> &mdio { >>> status = "okay"; >>> >>> phy at 0 { >>> reg = <0>; >>> ... >>> }; >>> }; >>> >>> versus: >>> >>> &mdio { >>> phy at 0 { >>> reg = <0>; >>> ... >>> }; >>> }; >>> >>> I think we can afford putting the mdio node's status property in each >>> board-level DTS and make it clear that way that it is enabled because >>> there are child nodes enabled? >> >> This will be a pretty big effort because every Northstar device I know >> has USB >> 3.0 PHY in the SoC. > > Adding a one liner is a "pretty big effort", for sure. Sorry, we got a misunderstanding here. I thought you meant adding something like this for every device: &mdio { status = "okay"; usb3_phy: usb-phy at 10 { compatible = "brcm,ns-ax-usb3-phy"; reg = <0x10>; usb3-dmp-syscon = <&usb3_dmp>; #phy-cells = <0>; }; }; usb3_dmp: syscon at 18105000 { reg = <0x18105000 0x1000>; }; So I clearly missed something important. Did you want to have USB 3.0 PHY defined in the dtsi file? ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] ARM: dts: BCM5301X: Specify MDIO bus in the DT 2017-04-19 18:10 ` Rafał Miłecki @ 2017-04-19 18:13 ` Florian Fainelli 0 siblings, 0 replies; 9+ messages in thread From: Florian Fainelli @ 2017-04-19 18:13 UTC (permalink / raw) To: linux-arm-kernel On 04/19/2017 11:10 AM, Rafa? Mi?ecki wrote: > On 04/19/2017 07:52 PM, Florian Fainelli wrote: >> On 04/19/2017 10:35 AM, Rafa? Mi?ecki wrote: >>> On 04/19/2017 06:43 PM, Florian Fainelli wrote: >>>> On 04/02/2017 02:25 PM, Rafa? Mi?ecki wrote: >>>>> On 04/02/2017 11:14 PM, Florian Fainelli wrote: >>>>>> Le 04/02/17 ? 14:08, Rafa? Mi?ecki a ?crit : >>>>>>> From: Rafa? Mi?ecki <rafal@milecki.pl> >>>>>>> >>>>>>> Northstar devices have MDIO bus that may contain various PHYs >>>>>>> attached. >>>>>>> A common example is USB 3.0 PHY (that doesn't have an MDIO driver >>>>>>> yet). >>>>>>> >>>>>>> Signed-off-by: Rafa? Mi?ecki <rafal@milecki.pl> >>>>>>> --- >>>>>>> arch/arm/boot/dts/bcm5301x.dtsi | 7 +++++++ >>>>>>> 1 file changed, 7 insertions(+) >>>>>>> >>>>>>> diff --git a/arch/arm/boot/dts/bcm5301x.dtsi >>>>>>> b/arch/arm/boot/dts/bcm5301x.dtsi >>>>>>> index acee36a61004..6a2afe7880ae 100644 >>>>>>> --- a/arch/arm/boot/dts/bcm5301x.dtsi >>>>>>> +++ b/arch/arm/boot/dts/bcm5301x.dtsi >>>>>>> @@ -320,6 +320,13 @@ >>>>>>> }; >>>>>>> }; >>>>>>> >>>>>>> + mdio at 18003000 { >>>>>>> + compatible = "brcm,iproc-mdio"; >>>>>>> + reg = <0x18003000 0x8>; >>>>>>> + #size-cells = <1>; >>>>>>> + #address-cells = <0>; >>>>>>> + }; >>>>>> >>>>>> This looks fine, but usually the block should be enabled on a >>>>>> per-board >>>>>> basis, such that there should be a status = "disabled" property >>>>>> here by >>>>>> default. >>>>> >>>>> I think we have few blocks in bcm5301x.dtsi enabled by default. I >>>>> guess >>>>> it's >>>>> for stuff that is always present on every SoC family board: rng, nand, >>>>> spi to >>>>> name few. >>>>> >>>>> It makes some sense, consider e.g. spi. Every Northstar board has SPI >>>>> controller so it's enabled by default. Not every board has SPI >>>>> flash, so >>>>> it's >>>>> disabled by default. >>>>> >>>>> It's there and it make sense to me. Is that OK or not? >>>> >>>> Even though there are devices that are always enabled on a given SoC, >>>> because the board designs are always consistent does not necessarily >>>> make them good candidates to be enabled at the .dtsi level. This is >>>> particularly true when there are external connections to blocks (SPI, >>>> NAND, USB, Ethernet, MDIO to name a few), having them disabled by >>>> default is safer as a starting point to begin with. >>> >>> In case of Northstar there is USB 3.0 PHY connected *internally* to this >>> MDIO. >>> I don't think any board manufacturer is able to rip SoC out of the MDIO >>> or the >>> USB 3.0 PHY. >> >> OK, then can you still resubmit a proper patch that a) puts that >> information in the commit message, and b) also adds a proper label to >> the mdio node such that it can later on be referenced by label in >> board-level DTS files? By that I mean: >> >> mdio: mdio at 18003000 { >> >> Thank you >> >>> >>> >>>>> I find MDIO situation quite simiar. It seems every Northstar board has >>>>> MDIO bus >>>>> just devices may differ and should not be enabled by default. >>>> >>>> In which case, the only difference, for you would be to do to, at the >>>> board-level DTS: >>>> >>>> &mdio { >>>> status = "okay"; >>>> >>>> phy at 0 { >>>> reg = <0>; >>>> ... >>>> }; >>>> }; >>>> >>>> versus: >>>> >>>> &mdio { >>>> phy at 0 { >>>> reg = <0>; >>>> ... >>>> }; >>>> }; >>>> >>>> I think we can afford putting the mdio node's status property in each >>>> board-level DTS and make it clear that way that it is enabled because >>>> there are child nodes enabled? >>> >>> This will be a pretty big effort because every Northstar device I know >>> has USB >>> 3.0 PHY in the SoC. >> >> Adding a one liner is a "pretty big effort", for sure. > > Sorry, we got a misunderstanding here. > > I thought you meant adding something like this for every device: > > &mdio { > status = "okay"; > > usb3_phy: usb-phy at 10 { > compatible = "brcm,ns-ax-usb3-phy"; > reg = <0x10>; > usb3-dmp-syscon = <&usb3_dmp>; > #phy-cells = <0>; > }; > }; Ah no, I would have just done the following in the per-board DTS: &mdio { status = "okay"; }; &usb3_phy { status = "okay"; }; &xhci { status = "okay"; }; Something like that. > > usb3_dmp: syscon at 18105000 { > reg = <0x18105000 0x1000>; > }; > > So I clearly missed something important. Did you want to have USB 3.0 PHY > defined in the dtsi file? Yes, I think it does make sense to have it defined in the .dtsi file because it's internal to the SoC, however it should probably be marked disabled by default, unless a board enables its xHCI controller, does that make sense? -- Florian ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH V2] ARM: dts: BCM5301X: Specify MDIO bus in the DT 2017-04-02 21:08 [PATCH] ARM: dts: BCM5301X: Specify MDIO bus in the DT Rafał Miłecki 2017-04-02 21:14 ` Florian Fainelli @ 2017-04-19 21:54 ` Rafał Miłecki 1 sibling, 0 replies; 9+ messages in thread From: Rafał Miłecki @ 2017-04-19 21:54 UTC (permalink / raw) To: linux-arm-kernel From: Rafa? Mi?ecki <rafal@milecki.pl> Northstar devices have MDIO bus that may contain various PHYs attached. A common example is USB 3.0 PHY (that doesn't have an MDIO driver yet). Signed-off-by: Rafa? Mi?ecki <rafal@milecki.pl> --- V2: Disable MDIO bus by default. Add mdio label to allow enabling it easily per board --- arch/arm/boot/dts/bcm5301x.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi index acee36a61004..1f34bc6905f2 100644 --- a/arch/arm/boot/dts/bcm5301x.dtsi +++ b/arch/arm/boot/dts/bcm5301x.dtsi @@ -320,6 +320,14 @@ }; }; + mdio: mdio at 18003000 { + compatible = "brcm,iproc-mdio"; + reg = <0x18003000 0x8>; + #size-cells = <1>; + #address-cells = <0>; + status = "disabled"; + }; + i2c0: i2c at 18009000 { compatible = "brcm,iproc-i2c"; reg = <0x18009000 0x50>; -- 2.11.0 ^ permalink raw reply related [flat|nested] 9+ messages in thread
end of thread, other threads:[~2017-04-19 21:54 UTC | newest] Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2017-04-02 21:08 [PATCH] ARM: dts: BCM5301X: Specify MDIO bus in the DT Rafał Miłecki 2017-04-02 21:14 ` Florian Fainelli 2017-04-02 21:25 ` Rafał Miłecki 2017-04-19 16:43 ` Florian Fainelli 2017-04-19 17:35 ` Rafał Miłecki 2017-04-19 17:52 ` Florian Fainelli 2017-04-19 18:10 ` Rafał Miłecki 2017-04-19 18:13 ` Florian Fainelli 2017-04-19 21:54 ` [PATCH V2] " Rafał Miłecki
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).