linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: kishon@ti.com (Kishon Vijay Abraham I)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 23/41] ARM: dts: dra72x: Create a common file with MMC/SD IOdelay data
Date: Fri, 19 May 2017 13:45:23 +0530	[thread overview]
Message-ID: <20170519081541.26753-24-kishon@ti.com> (raw)
In-Reply-To: <20170519081541.26753-1-kishon@ti.com>

From: Sekhar Nori <nsekhar@ti.com>

Add pinmux configuration for MMC module including IODELAY
values suggested in the data manual for the various supported
modes.

IOdelay data for both silicon revision 1.0 and 2.0 is
added here.

The datamanual revisions used are:
 * AM571x Silicon Revision 2.0: SPRS957D, Revised January 2017
 * AM571x Silicon Revision 1.0: SPRS919M, Revised November 2017
 * DRA71x : SPRS960B, Revised February 2017

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi | 350 ++++++++++++++++++++++++++++++
 1 file changed, 350 insertions(+)
 create mode 100644 arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi

diff --git a/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi b/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi
new file mode 100644
index 000000000000..088013c6dc6e
--- /dev/null
+++ b/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi
@@ -0,0 +1,350 @@
+/*
+ * MMC IOdelay values for TI's DRA72x, DRA71x and AM571x SoCs.
+ *
+ * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * Rules for modifying this file:
+ * a) Update of this file should typically correspond to a datamanual revision.
+ *    Datamanual revision that was used should be updated in comment below.
+ *    If there is no update to datamanual, do not update the values. If you
+ *    need to use values different from that recommended by the datamanual
+ *    for your design, then you should consider adding values to the device-
+ *    -tree file for your board directly.
+ * b) We keep the mode names as close to the datamanual as possible. So
+ *    if the manual calls a mode, DDR50, or DDR or DDR 1.8v or DDR 3.3v,
+ *    we follow that in code too.
+ * c) If the values change between multiple revisions of silicon, we add
+ *    a revision tag to both the new and old entry. Use 'rev10' for PG 1.0,
+ *    'rev20' for PG 2.0 and so on.
+ * d) The node name and node label should be the exact same string. This is
+ *    to curb naming creativity and achieve consistency.
+ * e) If in future, DRA71x and DRA72x values differ, then add 'dra71_' and
+ *    'dra72_' tag to entries. Both the new and old entries should gain a tag.
+ *
+ * Datamanual Revisions:
+ *
+ * AM571x Silicon Revision 2.0: SPRS957D, Revised January 2017
+ * AM571x Silicon Revision 1.0: SPRS919M, Revised November 2017
+ * DRA71x : SPRS960B, Revised February 2017
+ */
+
+&dra7_pmx_core {
+	mmc1_pins_default: mmc1_pins_default {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_sdr12: mmc1_pins_sdr12 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_hs: mmc1_pins_hs {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_sdr25: mmc1_pins_sdr25 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_sdr50: mmc1_pins_sdr50 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE15 | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE15 | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE15 | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE15 | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE15 | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE15 | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_ddr50_rev10: mmc1_pins_ddr50_rev10 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE14 | MUX_MODE0)	/* mmc1_clk.mmc1_clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE14 | MUX_MODE0)	/* mmc1_cmd.mmc1_cmd */
+			DRA7XX_CORE_IOPAD(0x375C, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE14 | MUX_MODE0)	/* mmc1_dat0.mmc1_dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE14 | MUX_MODE0)	/* mmc1_dat1.mmc1_dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE14 | MUX_MODE0)	/* mmc1_dat2.mmc1_dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE14 | MUX_MODE0)	/* mmc1_dat3.mmc1_dat3 */
+		>;
+	};
+
+	mmc1_pins_ddr50_rev20: mmc1_pins_ddr50_rev20 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_sdr104: mmc1_pins_sdr104 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc2_pins_default: mmc2_pins_default {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	mmc2_pins_hs: mmc2_pins_hs {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	mmc2_pins_ddr_rev10: mmc2_pins_ddr_rev10 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a22.mmc2_dat7 */
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_cs1.mmc2_cmd */
+		>;
+	};
+
+	mmc2_pins_ddr_rev20: mmc2_pins_ddr_rev20 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	mmc2_pins_hs200: mmc2_pins_hs200 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+};
+
+&dra7_iodelay_core {
+
+	/* Corresponds to MMC1_MANUAL1 in datamanual */
+	mmc1_iodelay_ddr50_conf: mmc1_iodelay_ddr50_conf {
+		pinctrl-pin-array = <
+			0x618 A_DELAY_PS(588) G_DELAY_PS(0)	/* CFG_MMC1_CLK_IN */
+			0x624 A_DELAY_PS(1000) G_DELAY_PS(0)	/* CFG_MMC1_CMD_IN */
+			0x630 A_DELAY_PS(1375) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_IN */
+			0x63C A_DELAY_PS(1000) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_IN */
+			0x648 A_DELAY_PS(1000) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_IN */
+			0x654 A_DELAY_PS(1000) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_IN */
+			0x620 A_DELAY_PS(1230) G_DELAY_PS(0)	/* CFG_MMC1_CLK_OUT */
+			0x62C A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OUT */
+			0x638 A_DELAY_PS(56) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OUT */
+			0x644 A_DELAY_PS(76) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OUT */
+			0x650 A_DELAY_PS(91) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OUT */
+			0x65C A_DELAY_PS(99) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OUT */
+			0x628 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OEN */
+			0x634 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OEN */
+			0x640 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OEN */
+			0x64C A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OEN */
+			0x658 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OEN */
+		>;
+	};
+
+	/* Corresponds to MMC1_MANUAL2 in datamanual */
+	mmc1_iodelay_sdr104_rev10_conf: mmc1_iodelay_sdr104_rev10_conf {
+		pinctrl-pin-array = <
+			0x620 A_DELAY_PS(560) G_DELAY_PS(365)	/* CFG_MMC1_CLK_OUT */
+			0x62c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OUT */
+			0x638 A_DELAY_PS(29) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OUT */
+			0x644 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OUT */
+			0x650 A_DELAY_PS(47) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OUT */
+			0x65c A_DELAY_PS(30) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OUT */
+			0x628 A_DELAY_PS(125) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OEN */
+			0x634 A_DELAY_PS(43) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OEN */
+			0x640 A_DELAY_PS(433) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OEN */
+			0x64c A_DELAY_PS(287) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OEN */
+			0x658 A_DELAY_PS(351) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OEN */
+		>;
+	};
+
+	/* Corresponds to MMC1_MANUAL2 in datamanual */
+	mmc1_iodelay_sdr104_rev20_conf: mmc1_iodelay_sdr104_rev20_conf {
+		pinctrl-pin-array = <
+			0x620 A_DELAY_PS(520) G_DELAY_PS(320)	/* CFG_MMC1_CLK_OUT */
+			0x62c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OUT */
+			0x638 A_DELAY_PS(40) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OUT */
+			0x644 A_DELAY_PS(83) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OUT */
+			0x650 A_DELAY_PS(98) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OUT */
+			0x65c A_DELAY_PS(106) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OUT */
+			0x628 A_DELAY_PS(51) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OEN */
+			0x634 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OEN */
+			0x640 A_DELAY_PS(363) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OEN */
+			0x64c A_DELAY_PS(199) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OEN */
+			0x658 A_DELAY_PS(273) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OEN */
+		>;
+	};
+
+	/* Corresponds to MMC2_MANUAL1 in datamanual */
+	mmc2_iodelay_ddr_conf: mmc2_iodelay_ddr_conf {
+		pinctrl-pin-array = <
+			0x18c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A19_IN */
+			0x1a4 A_DELAY_PS(119) G_DELAY_PS(0)	/* CFG_GPMC_A20_IN */
+			0x1b0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A21_IN */
+			0x1bc A_DELAY_PS(18) G_DELAY_PS(0)	/* CFG_GPMC_A22_IN */
+			0x1c8 A_DELAY_PS(894) G_DELAY_PS(0)	/* CFG_GPMC_A23_IN */
+			0x1d4 A_DELAY_PS(30) G_DELAY_PS(0)	/* CFG_GPMC_A24_IN */
+			0x1e0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A25_IN */
+			0x1ec A_DELAY_PS(23) G_DELAY_PS(0)	/* CFG_GPMC_A26_IN */
+			0x1f8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A27_IN */
+			0x360 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_CS1_IN */
+			0x194 A_DELAY_PS(152) G_DELAY_PS(0)	/* CFG_GPMC_A19_OUT */
+			0x1ac A_DELAY_PS(206) G_DELAY_PS(0)	/* CFG_GPMC_A20_OUT */
+			0x1b8 A_DELAY_PS(78) G_DELAY_PS(0)	/* CFG_GPMC_A21_OUT */
+			0x1c4 A_DELAY_PS(2) G_DELAY_PS(0)	/* CFG_GPMC_A22_OUT */
+			0x1d0 A_DELAY_PS(266) G_DELAY_PS(0)	/* CFG_GPMC_A23_OUT */
+			0x1dc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A24_OUT */
+			0x1e8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A25_OUT */
+			0x1f4 A_DELAY_PS(43) G_DELAY_PS(0)	/* CFG_GPMC_A26_OUT */
+			0x200 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A27_OUT */
+			0x368 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_CS1_OUT */
+			0x190 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A19_OEN */
+			0x1a8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A20_OEN */
+			0x1b4 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A21_OEN */
+			0x1c0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A22_OEN */
+			0x1d8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A24_OEN */
+			0x1e4 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A25_OEN */
+			0x1f0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A26_OEN */
+			0x1fc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A27_OEN */
+			0x364 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_CS1_OEN */
+		>;
+	};
+
+	/* Corresponds to MMC2_MANUAL3 in datamanual */
+	mmc2_iodelay_hs200_rev10_conf: mmc2_iodelay_hs200_rev10_conf {
+		pinctrl-pin-array = <
+			0x194 A_DELAY_PS(150) G_DELAY_PS(95)	/* CFG_GPMC_A19_OUT */
+			0x1ac A_DELAY_PS(250) G_DELAY_PS(0)	/* CFG_GPMC_A20_OUT */
+			0x1b8 A_DELAY_PS(125) G_DELAY_PS(0)	/* CFG_GPMC_A21_OUT */
+			0x1c4 A_DELAY_PS(100) G_DELAY_PS(0)	/* CFG_GPMC_A22_OUT */
+			0x1d0 A_DELAY_PS(870) G_DELAY_PS(415)	/* CFG_GPMC_A23_OUT */
+			0x1dc A_DELAY_PS(30) G_DELAY_PS(0)	/* CFG_GPMC_A24_OUT */
+			0x1e8 A_DELAY_PS(200) G_DELAY_PS(0)	/* CFG_GPMC_A25_OUT */
+			0x1f4 A_DELAY_PS(200) G_DELAY_PS(0)	/* CFG_GPMC_A26_OUT */
+			0x200 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A27_OUT */
+			0x368 A_DELAY_PS(240) G_DELAY_PS(0)	/* CFG_GPMC_CS1_OUT */
+			0x190 A_DELAY_PS(695) G_DELAY_PS(0)	/* CFG_GPMC_A19_OEN */
+			0x1a8 A_DELAY_PS(924) G_DELAY_PS(0)	/* CFG_GPMC_A20_OEN */
+			0x1b4 A_DELAY_PS(719) G_DELAY_PS(0)	/* CFG_GPMC_A21_OEN */
+			0x1c0 A_DELAY_PS(824) G_DELAY_PS(0)	/* CFG_GPMC_A22_OEN */
+			0x1d8 A_DELAY_PS(877) G_DELAY_PS(0)	/* CFG_GPMC_A24_OEN */
+			0x1e4 A_DELAY_PS(446) G_DELAY_PS(0)	/* CFG_GPMC_A25_OEN */
+			0x1f0 A_DELAY_PS(847) G_DELAY_PS(0)	/* CFG_GPMC_A26_OEN */
+			0x1fc A_DELAY_PS(586) G_DELAY_PS(0)	/* CFG_GPMC_A27_OEN */
+			0x364 A_DELAY_PS(1039) G_DELAY_PS(0)	/* CFG_GPMC_CS1_OEN */
+		>;
+	};
+
+	/* Corresponds to MMC2_MANUAL3 in datamanual */
+	mmc2_iodelay_hs200_rev20_conf: mmc2_iodelay_hs200_rev20_conf {
+		pinctrl-pin-array = <
+			0x194 A_DELAY_PS(285) G_DELAY_PS(0)	/* CFG_GPMC_A19_OUT */
+			0x1ac A_DELAY_PS(189) G_DELAY_PS(0)	/* CFG_GPMC_A20_OUT */
+			0x1b8 A_DELAY_PS(0) G_DELAY_PS(120)	/* CFG_GPMC_A21_OUT */
+			0x1c4 A_DELAY_PS(0) G_DELAY_PS(70)	/* CFG_GPMC_A22_OUT */
+			0x1d0 A_DELAY_PS(730) G_DELAY_PS(360)	/* CFG_GPMC_A23_OUT */
+			0x1dc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A24_OUT */
+			0x1e8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A25_OUT */
+			0x1f4 A_DELAY_PS(70) G_DELAY_PS(0)	/* CFG_GPMC_A26_OUT */
+			0x200 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A27_OUT */
+			0x368 A_DELAY_PS(0) G_DELAY_PS(120)	/* CFG_GPMC_CS1_OUT */
+			0x190 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A19_OEN */
+			0x1a8 A_DELAY_PS(231) G_DELAY_PS(0)	/* CFG_GPMC_A20_OEN */
+			0x1b4 A_DELAY_PS(39) G_DELAY_PS(0)	/* CFG_GPMC_A21_OEN */
+			0x1c0 A_DELAY_PS(91) G_DELAY_PS(0)	/* CFG_GPMC_A22_OEN */
+			0x1d8 A_DELAY_PS(176) G_DELAY_PS(0)	/* CFG_GPMC_A24_OEN */
+			0x1e4 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A25_OEN */
+			0x1f0 A_DELAY_PS(101) G_DELAY_PS(0)	/* CFG_GPMC_A26_OEN */
+			0x1fc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A27_OEN */
+			0x364 A_DELAY_PS(360) G_DELAY_PS(0)	/* CFG_GPMC_CS1_OEN */
+		>;
+	};
+};
-- 
2.11.0

  parent reply	other threads:[~2017-05-19  8:15 UTC|newest]

Thread overview: 46+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-05-19  8:15 [PATCH 00/41] omap_hsmmc: Add ADMA support and UHS/HS200/DDR support Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 01/41] mmc: host: omap_hsmmc: Support pbias and vmmc_aux to switch to 1.8v Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 02/41] mmc: host: omap_hsmmc: Separate setting voltage capabilities from bus power Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 03/41] mmc: host: omap_hsmmc: Program HCTL based on signal_voltage set by mmc core Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 04/41] mmc: host: omap_hsmmc: Add voltage switch support for UHS SD card Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 05/41] mmc: host: omap_hsmmc: Set clk rate to the max frequency Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 06/41] mmc: host: omap_hsmmc: Add tuning support Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 07/41] mmc: host: omap_hsmmc: Allow io voltage switch even for fixed vdd Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 08/41] mmc: host: omap_hsmmc: Remove incorrect voltage switch sequence Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 09/41] mmc: host: omap_hsmmc: Add software timer when timeout greater than hardware capablility Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 10/41] mmc: host: omap_hsmmc: Prepare *set_timing() to be used for iodelay setting Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 11/41] mmc: host: omap_hsmmc: Add new compatible string to support dra7 Kishon Vijay Abraham I
2017-05-23 14:44   ` Rob Herring
2017-05-19  8:15 ` [PATCH 12/41] mmc: host: omap_hsmmc: Fix error path sequence Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 13/41] mmc: host: omap_hsmmc: Add support to set IODELAY values Kishon Vijay Abraham I
2017-05-23 14:55   ` Rob Herring
2017-05-19  8:15 ` [PATCH 14/41] mmc: host: omap_hsmmc: Remove *use_dma* member Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 15/41] mmc: host: omap_hsmmc: Enable ADMA2 Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 16/41] mmc: omap_hsmmc: Support non-1.8V IO controllers Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 17/41] ARM: dts: dra72-evm: Add vmmc_aux supply to mmc1 Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 18/41] ARM: dts: dra72-evm-revc: " Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 19/41] ARM: dts: am57xx-beagle-x15-revb1: Fix supply name used for MMC1 IO lines Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 20/41] ARM: dts: dra7-evm: Correct the vmmc-supply for mmc2 Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 21/41] ARM: dts: dra72-evm-common: Correct " Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 22/41] ARM: dts: Add dra7 iodelay configuration Kishon Vijay Abraham I
2017-05-19  8:15 ` Kishon Vijay Abraham I [this message]
2017-05-19  8:15 ` [PATCH 24/41] ARM: dts: dra74x: Create a common file with MMC/SD IOdelay data Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 25/41] ARM: dts: dra7-evm: Add pinmux configuration for MMC Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 26/41] ARM: dts: am57xx-beagle-x15: " Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 27/41] ARM: dts: am57xx-idk: Move common MMC/SD properties to common file Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 28/41] ARM: dts: am571x-idk: Add pinmux configuration for MMC Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 29/41] ARM: dts: am572x-idk: " Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 30/41] ARM: dts: dra72-evm: " Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 31/41] ARM: dts: dra72-evm-revc: " Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 32/41] ARM: dts: dra71-evm: " Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 33/41] ARM: dts: dra7: Add "max-frequency" property to MMC dt nodes Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 34/41] ARM: dts: dra7: Use new dra7-specific compatible string Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 35/41] ARM: dts: dra7: Add supported MMC/SD modes in MMC dt nodes Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 36/41] ARM: dts: am57xx-idk: Set MMC2 IO voltage to 3.3V Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 37/41] ARM: dts: am57xx-beagle-x15-common: " Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 38/41] ARM: OMAP2+: Add pdata-quirks for MMC/SD on DRA74x EVM Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 39/41] ARM: omap2plus_defconfig: Enable PINCTRL_TI_IODELAY Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 40/41] ARM: multi_v7_defconfig: " Kishon Vijay Abraham I
2017-05-19  8:15 ` [PATCH 41/41] Documentation: ARM: Document new dependencies for MMC on DRA7 Kishon Vijay Abraham I
2017-05-19 22:13 ` [PATCH 00/41] omap_hsmmc: Add ADMA support and UHS/HS200/DDR support Tony Lindgren
2017-05-22 12:20   ` Kishon Vijay Abraham I

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20170519081541.26753-24-kishon@ti.com \
    --to=kishon@ti.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).