* [PATCH v2 2/4] arm64: dts: rockchip: add usb3 controller node for RK3328 SoCs
2017-12-04 9:40 [PATCH v2 1/4] dt-bindings: usb: add DT binding for RK3328 dwc3 controller Heiko Stuebner
@ 2017-12-04 9:40 ` Heiko Stuebner
2017-12-04 9:40 ` [PATCH v2 3/4] arm64: dts: rockchip: enable usb3 for RK3328 evaluation board Heiko Stuebner
` (4 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: Heiko Stuebner @ 2017-12-04 9:40 UTC (permalink / raw)
To: linux-arm-kernel
From: William Wu <william.wu@rock-chips.com>
RK3328 has one USB 3.0 OTG controller which uses DWC_USB3
core's general architecture. It can act as static xHCI host
controller, static device controller, USB 3.0/2.0 OTG basing
on ID of USB3.0 PHY.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
---
changes in v2:
none
arch/arm64/boot/dts/rockchip/rk3328.dtsi | 27 +++++++++++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
index 41d61840fb99..cafc572a68e0 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
@@ -805,6 +805,33 @@
status = "disabled";
};
+ usbdrd3: usb at ff600000 {
+ compatible = "rockchip,rk3328-dwc3", "rockchip,rk3399-dwc3";
+ clocks = <&cru SCLK_USB3OTG_REF>, <&cru SCLK_USB3OTG_SUSPEND>,
+ <&cru ACLK_USB3OTG>;
+ clock-names = "ref_clk", "suspend_clk",
+ "bus_clk";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ usbdrd_dwc3: dwc3 at ff600000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0xff600000 0x0 0x100000>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ dr_mode = "otg";
+ phy_type = "utmi_wide";
+ snps,dis_enblslpm_quirk;
+ snps,dis-u2-freeclk-exists-quirk;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_u3_susphy_quirk;
+ snps,dis-del-phy-power-chg-quirk;
+ snps,dis-tx-ipgap-linecheck-quirk;
+ status = "disabled";
+ };
+ };
+
gic: interrupt-controller at ff811000 {
compatible = "arm,gic-400";
#interrupt-cells = <3>;
--
2.14.2
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 3/4] arm64: dts: rockchip: enable usb3 for RK3328 evaluation board
2017-12-04 9:40 [PATCH v2 1/4] dt-bindings: usb: add DT binding for RK3328 dwc3 controller Heiko Stuebner
2017-12-04 9:40 ` [PATCH v2 2/4] arm64: dts: rockchip: add usb3 controller node for RK3328 SoCs Heiko Stuebner
@ 2017-12-04 9:40 ` Heiko Stuebner
2017-12-04 9:40 ` [PATCH v2 4/4] arm64: dts: rockchip: enable usb3 nodes on rk3328-rock64 Heiko Stuebner
` (3 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: Heiko Stuebner @ 2017-12-04 9:40 UTC (permalink / raw)
To: linux-arm-kernel
From: William Wu <william.wu@rock-chips.com>
Rockchip's RK3328 evaluation board has one USB 3.0 OTG controller,
we enable it and set it act as static xHCI host controller to
support USB 3.0 HOST on RK3328 evaluation board.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
---
changes in v2:
none
arch/arm64/boot/dts/rockchip/rk3328-evb.dts | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-evb.dts b/arch/arm64/boot/dts/rockchip/rk3328-evb.dts
index 3d551e3e6c23..95fba84239a7 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-evb.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-evb.dts
@@ -306,3 +306,12 @@
&usb_host0_ohci {
status = "okay";
};
+
+&usbdrd3 {
+ status = "okay";
+};
+
+&usbdrd_dwc3 {
+ dr_mode = "host";
+ status = "okay";
+};
--
2.14.2
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 4/4] arm64: dts: rockchip: enable usb3 nodes on rk3328-rock64
2017-12-04 9:40 [PATCH v2 1/4] dt-bindings: usb: add DT binding for RK3328 dwc3 controller Heiko Stuebner
2017-12-04 9:40 ` [PATCH v2 2/4] arm64: dts: rockchip: add usb3 controller node for RK3328 SoCs Heiko Stuebner
2017-12-04 9:40 ` [PATCH v2 3/4] arm64: dts: rockchip: enable usb3 for RK3328 evaluation board Heiko Stuebner
@ 2017-12-04 9:40 ` Heiko Stuebner
2017-12-04 9:42 ` [PATCH v2 1/4] dt-bindings: usb: add DT binding for RK3328 dwc3 controller Heiko Stuebner
` (2 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: Heiko Stuebner @ 2017-12-04 9:40 UTC (permalink / raw)
To: linux-arm-kernel
Enable the nodes to make the usb3 port usable on that board.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
---
changes in v2:
- new patch
arch/arm64/boot/dts/rockchip/rk3328-rock64.dts | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
index d4f80786e7c2..e393c3586c11 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
@@ -331,3 +331,12 @@
&usb_host0_ohci {
status = "okay";
};
+
+&usbdrd3 {
+ status = "okay";
+};
+
+&usbdrd_dwc3 {
+ dr_mode = "host";
+ status = "okay";
+};
--
2.14.2
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 1/4] dt-bindings: usb: add DT binding for RK3328 dwc3 controller
2017-12-04 9:40 [PATCH v2 1/4] dt-bindings: usb: add DT binding for RK3328 dwc3 controller Heiko Stuebner
` (2 preceding siblings ...)
2017-12-04 9:40 ` [PATCH v2 4/4] arm64: dts: rockchip: enable usb3 nodes on rk3328-rock64 Heiko Stuebner
@ 2017-12-04 9:42 ` Heiko Stuebner
2017-12-16 15:52 ` Heiko Stuebner
2017-12-27 18:22 ` Heiko Stuebner
5 siblings, 0 replies; 8+ messages in thread
From: Heiko Stuebner @ 2017-12-04 9:42 UTC (permalink / raw)
To: linux-arm-kernel
Am Montag, 4. Dezember 2017, 10:40:38 CET schrieb Heiko Stuebner:
> From: William Wu <william.wu@rock-chips.com>
>
> Adds the device tree bindings description for RK3328 and
> compatible USB DWC3 controller.
>
> Signed-off-by: William Wu <william.wu@rock-chips.com>
> Acked-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
> ---
> changes in v2:
> - add Rob's Ack
>
> Ideally usb maintainers would pick up this patch to the binding
> document and I'll take the devicetree changes after that.
>
> But if so desired, I can also pick up the binding change myself
> but would need an Ack for that.
just realized, the last version from august was actually v3, so this
should be v4, not v2 ... sorry about that.
Heiko
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v2 1/4] dt-bindings: usb: add DT binding for RK3328 dwc3 controller
2017-12-04 9:40 [PATCH v2 1/4] dt-bindings: usb: add DT binding for RK3328 dwc3 controller Heiko Stuebner
` (3 preceding siblings ...)
2017-12-04 9:42 ` [PATCH v2 1/4] dt-bindings: usb: add DT binding for RK3328 dwc3 controller Heiko Stuebner
@ 2017-12-16 15:52 ` Heiko Stuebner
2017-12-18 9:00 ` Felipe Balbi
2017-12-27 18:22 ` Heiko Stuebner
5 siblings, 1 reply; 8+ messages in thread
From: Heiko Stuebner @ 2017-12-16 15:52 UTC (permalink / raw)
To: linux-arm-kernel
Hi Greg, Felipe,
Am Montag, 4. Dezember 2017, 10:40:38 CET schrieb Heiko Stuebner:
> From: William Wu <william.wu@rock-chips.com>
>
> Adds the device tree bindings description for RK3328 and
> compatible USB DWC3 controller.
>
> Signed-off-by: William Wu <william.wu@rock-chips.com>
> Acked-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
do you want to pick this patch with only the small dt-binding
change or Ack it for me to pick up together with the actual
devicetree changes in the other patches?
Thanks
Heiko
> ---
> changes in v2:
> - add Rob's Ack
>
> Ideally usb maintainers would pick up this patch to the binding
> document and I'll take the devicetree changes after that.
>
> But if so desired, I can also pick up the binding change myself
> but would need an Ack for that.
>
> Documentation/devicetree/bindings/usb/rockchip,dwc3.txt | 4 +++-
> 1 file changed, 3 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
> index 50a31536e975..2c3f6a467fda 100644
> --- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
> +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
> @@ -1,7 +1,9 @@
> Rockchip SuperSpeed DWC3 USB SoC controller
>
> Required properties:
> -- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC
> +- compatible: should be one of the following:
> + - "rockchip,rk3399-dwc3": for rk3399 SoC
> + - "rockchip,rk3328-dwc3", "rockchip,rk3399-dwc3": for rk3328 SoC
> - clocks: A list of phandle + clock-specifier pairs for the
> clocks listed in clock-names
> - clock-names: Should contain the following:
>
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v2 1/4] dt-bindings: usb: add DT binding for RK3328 dwc3 controller
2017-12-16 15:52 ` Heiko Stuebner
@ 2017-12-18 9:00 ` Felipe Balbi
0 siblings, 0 replies; 8+ messages in thread
From: Felipe Balbi @ 2017-12-18 9:00 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
Heiko Stuebner <heiko@sntech.de> writes:
> Hi Greg, Felipe,
>
> Am Montag, 4. Dezember 2017, 10:40:38 CET schrieb Heiko Stuebner:
>> From: William Wu <william.wu@rock-chips.com>
>>
>> Adds the device tree bindings description for RK3328 and
>> compatible USB DWC3 controller.
>>
>> Signed-off-by: William Wu <william.wu@rock-chips.com>
>> Acked-by: Rob Herring <robh@kernel.org>
>> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
>
> do you want to pick this patch with only the small dt-binding
> change or Ack it for me to pick up together with the actual
> devicetree changes in the other patches?
it seems best if you carry this one:
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
--
balbi
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v2 1/4] dt-bindings: usb: add DT binding for RK3328 dwc3 controller
2017-12-04 9:40 [PATCH v2 1/4] dt-bindings: usb: add DT binding for RK3328 dwc3 controller Heiko Stuebner
` (4 preceding siblings ...)
2017-12-16 15:52 ` Heiko Stuebner
@ 2017-12-27 18:22 ` Heiko Stuebner
5 siblings, 0 replies; 8+ messages in thread
From: Heiko Stuebner @ 2017-12-27 18:22 UTC (permalink / raw)
To: linux-arm-kernel
Am Montag, 4. Dezember 2017, 10:40:38 CET schrieb Heiko Stuebner:
> From: William Wu <william.wu@rock-chips.com>
>
> Adds the device tree bindings description for RK3328 and
> compatible USB DWC3 controller.
>
> Signed-off-by: William Wu <william.wu@rock-chips.com>
> Acked-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
applied all 4 with Felipe's Ack on patch1
^ permalink raw reply [flat|nested] 8+ messages in thread