* [PATCH v3] ARM: dts: sun8i-h3: Add support for the RerVision H3-DVK board
@ 2019-03-15 12:38 Paul Kocialkowski
2019-03-15 14:16 ` Maxime Ripard
0 siblings, 1 reply; 2+ messages in thread
From: Paul Kocialkowski @ 2019-03-15 12:38 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-arm-kernel, linux-sunxi
Cc: Mark Rutland, Maxime Ripard, Paul Kocialkowski, Chen-Yu Tsai,
Rob Herring, Thomas Petazzoni
This is an H3-based board that sticks close to the reference design.
Supported features:
* UART
* DRAM
* MMC
* eMMC
* Ethernet
* USB host
* USB peripheral
* HDMI
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
---
Changes since v2:
* Actually made the changes instead of sending the same patch again.
Changes since v1:
* Removed unneeded changes to mmc2_8bit_pins node;
* Renamed HDMI connector nodes to match other boards.
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun8i-h3-rervision-dvk.dts | 114 +++++++++++++++++++
2 files changed, 115 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-h3-rervision-dvk.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index bd40148a15b2..8db275b75214 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1078,6 +1078,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-h3-orangepi-plus.dtb \
sun8i-h3-orangepi-plus2e.dtb \
sun8i-h3-orangepi-zero-plus2.dtb \
+ sun8i-h3-rervision-dvk.dtb \
sun8i-r16-bananapi-m2m.dtb \
sun8i-r16-nintendo-nes-classic.dtb \
sun8i-r16-nintendo-super-nes-classic.dtb \
diff --git a/arch/arm/boot/dts/sun8i-h3-rervision-dvk.dts b/arch/arm/boot/dts/sun8i-h3-rervision-dvk.dts
new file mode 100644
index 000000000000..51bd2c00bbae
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-rervision-dvk.dts
@@ -0,0 +1,114 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Bootlin
+ * Author: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "RerVision H3-DVK";
+ compatible = "rervision,h3-dvk", "allwinner,sun8i-h3";
+
+ aliases {
+ ethernet0 = &emac;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&mmc0 {
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+ vmmc-supply = <®_vcc3v3>;
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usb_otg {
+ status = "okay";
+ dr_mode = "peripheral";
+};
+
+&usbphy {
+ status = "okay";
+};
--
2.21.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCH v3] ARM: dts: sun8i-h3: Add support for the RerVision H3-DVK board
2019-03-15 12:38 [PATCH v3] ARM: dts: sun8i-h3: Add support for the RerVision H3-DVK board Paul Kocialkowski
@ 2019-03-15 14:16 ` Maxime Ripard
0 siblings, 0 replies; 2+ messages in thread
From: Maxime Ripard @ 2019-03-15 14:16 UTC (permalink / raw)
To: Paul Kocialkowski
Cc: Mark Rutland, devicetree, linux-kernel, linux-sunxi, Rob Herring,
Thomas Petazzoni, Chen-Yu Tsai, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 455 bytes --]
On Fri, Mar 15, 2019 at 01:38:28PM +0100, Paul Kocialkowski wrote:
> This is an H3-based board that sticks close to the reference design.
>
> Supported features:
> * UART
> * DRAM
> * MMC
> * eMMC
> * Ethernet
> * USB host
> * USB peripheral
> * HDMI
>
> Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Applied, thanks!
Maxime
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2019-03-15 14:16 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-03-15 12:38 [PATCH v3] ARM: dts: sun8i-h3: Add support for the RerVision H3-DVK board Paul Kocialkowski
2019-03-15 14:16 ` Maxime Ripard
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).