* [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device
@ 2019-05-20 13:24 Fabio Estevam
2019-05-20 13:24 ` [PATCH RESEND 2/2] ARM: dts: imx53-smd: Add OV5642 video capture support Fabio Estevam
2019-05-23 9:06 ` [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device Shawn Guo
0 siblings, 2 replies; 3+ messages in thread
From: Fabio Estevam @ 2019-05-20 13:24 UTC (permalink / raw)
To: shawnguo; +Cc: linux-arm-kernel, Fabio Estevam, linux-imx, kernel, slongerbeam
From: Steve Longerbeam <slongerbeam@gmail.com>
Add video capture_subsystem device node, and include both CSI ports.
Prepare for adding sensors by adding the parallel sensor anchor endpoints
to the CSI ports.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
---
arch/arm/boot/dts/imx53.dtsi | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/imx53.dtsi
index 9b672ed2486d..ed341cfd9d09 100644
--- a/arch/arm/boot/dts/imx53.dtsi
+++ b/arch/arm/boot/dts/imx53.dtsi
@@ -31,6 +31,7 @@
i2c0 = &i2c1;
i2c1 = &i2c2;
i2c2 = &i2c3;
+ ipu0 = &ipu;
mmc0 = &esdhc1;
mmc1 = &esdhc2;
mmc2 = &esdhc3;
@@ -71,6 +72,11 @@
ports = <&ipu_di0>, <&ipu_di1>;
};
+ capture_subsystem {
+ compatible = "fsl,imx-capture-subsystem";
+ ports = <&ipu_csi0>, <&ipu_csi1>;
+ };
+
tzic: tz-interrupt-controller@fffc000 {
compatible = "fsl,imx53-tzic", "fsl,tzic";
interrupt-controller;
@@ -158,10 +164,16 @@
ipu_csi0: port@0 {
reg = <0>;
+
+ ipu_csi0_from_parallel_sensor: endpoint {
+ };
};
ipu_csi1: port@1 {
reg = <1>;
+
+ ipu_csi1_from_parallel_sensor: endpoint {
+ };
};
ipu_di0: port@2 {
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH RESEND 2/2] ARM: dts: imx53-smd: Add OV5642 video capture support
2019-05-20 13:24 [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device Fabio Estevam
@ 2019-05-20 13:24 ` Fabio Estevam
2019-05-23 9:06 ` [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device Shawn Guo
1 sibling, 0 replies; 3+ messages in thread
From: Fabio Estevam @ 2019-05-20 13:24 UTC (permalink / raw)
To: shawnguo; +Cc: linux-arm-kernel, Fabio Estevam, linux-imx, kernel, slongerbeam
From: Steve Longerbeam <slongerbeam@gmail.com>
Add video capture support from the OV5642 to IPU CSI0 on
the i.MX53 SMD.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
[fabio: remove unnecessary 'regulator-always-on' from camera regulators]
Signed-off-by: Fabio Estevam <festevam@gmail.com>
---
arch/arm/boot/dts/imx53-smd.dts | 73 +++++++++++++++++++++++++++++++++
1 file changed, 73 insertions(+)
diff --git a/arch/arm/boot/dts/imx53-smd.dts b/arch/arm/boot/dts/imx53-smd.dts
index 09071ca11c6c..ffdc6d990795 100644
--- a/arch/arm/boot/dts/imx53-smd.dts
+++ b/arch/arm/boot/dts/imx53-smd.dts
@@ -185,6 +185,31 @@
>;
};
+ pinctrl_ipu_csi0: ipucsi0grp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT12__IPU_CSI0_D_12 0x1c4
+ MX53_PAD_CSI0_DAT13__IPU_CSI0_D_13 0x1c4
+ MX53_PAD_CSI0_DAT14__IPU_CSI0_D_14 0x1c4
+ MX53_PAD_CSI0_DAT15__IPU_CSI0_D_15 0x1c4
+ MX53_PAD_CSI0_DAT16__IPU_CSI0_D_16 0x1c4
+ MX53_PAD_CSI0_DAT17__IPU_CSI0_D_17 0x1c4
+ MX53_PAD_CSI0_DAT18__IPU_CSI0_D_18 0x1c4
+ MX53_PAD_CSI0_DAT19__IPU_CSI0_D_19 0x1c4
+ MX53_PAD_CSI0_PIXCLK__IPU_CSI0_PIXCLK 0x1e4
+ MX53_PAD_CSI0_VSYNC__IPU_CSI0_VSYNC 0x1e4
+ MX53_PAD_CSI0_MCLK__IPU_CSI0_HSYNC 0x1e4
+ MX53_PAD_CSI0_DATA_EN__IPU_CSI0_DATA_EN 0x1e4
+ >;
+ };
+
+ pinctrl_ov5642: ov5642grp {
+ fsl,pins = <
+ MX53_PAD_NANDF_WP_B__GPIO6_9 0x1e4
+ MX53_PAD_NANDF_RB0__GPIO6_10 0x1e4
+ MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x1c4
+ >;
+ };
+
pinctrl_uart1: uart1grp {
fsl,pins = <
MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4
@@ -256,11 +281,47 @@
camera: ov5642@3c {
compatible = "ovti,ov5642";
reg = <0x3c>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5642>;
+ assigned-clocks = <&clks IMX5_CLK_SSI_EXT1_SEL>,
+ <&clks IMX5_CLK_SSI_EXT1_COM_SEL>;
+ assigned-clock-parents = <&clks IMX5_CLK_PLL2_SW>,
+ <&clks IMX5_CLK_SSI_EXT1_PODF>;
+ assigned-clock-rates = <0>, <24000000>;
+ clocks = <&clks IMX5_CLK_SSI_EXT1_GATE>;
+ clock-names = "xclk";
+ DVDD-supply = <&ldo9_reg>;
+ AVDD-supply = <&ldo7_reg>;
+ reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
+ powerdown-gpios = <&gpio6 10 GPIO_ACTIVE_HIGH>;
+
+ port {
+ ov5642_to_ipu_csi0: endpoint {
+ remote-endpoint = <&ipu_csi0_from_parallel_sensor>;
+ bus-width = <8>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
};
pmic: dialog@48 {
compatible = "dlg,da9053", "dlg,da9052";
reg = <0x48>;
+ interrupt-parent = <&gpio7>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ ldo7_reg: ldo7 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ };
+
+ ldo9_reg: ldo9 {
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <3650000>;
+ };
+ };
};
};
@@ -271,3 +332,15 @@
phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
status = "okay";
};
+
+&ipu_csi0_from_parallel_sensor {
+ remote-endpoint = <&ov5642_to_ipu_csi0>;
+ data-shift = <12>; /* Lines 19:12 used */
+ hsync-active = <1>;
+ vsync-active = <1>;
+};
+
+&ipu_csi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu_csi0>;
+};
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device
2019-05-20 13:24 [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device Fabio Estevam
2019-05-20 13:24 ` [PATCH RESEND 2/2] ARM: dts: imx53-smd: Add OV5642 video capture support Fabio Estevam
@ 2019-05-23 9:06 ` Shawn Guo
1 sibling, 0 replies; 3+ messages in thread
From: Shawn Guo @ 2019-05-23 9:06 UTC (permalink / raw)
To: Fabio Estevam; +Cc: linux-arm-kernel, linux-imx, kernel, slongerbeam
On Mon, May 20, 2019 at 10:24:10AM -0300, Fabio Estevam wrote:
> From: Steve Longerbeam <slongerbeam@gmail.com>
>
> Add video capture_subsystem device node, and include both CSI ports.
> Prepare for adding sensors by adding the parallel sensor anchor endpoints
> to the CSI ports.
>
> Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
> Signed-off-by: Fabio Estevam <festevam@gmail.com>
Applied both, thanks.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2019-05-23 9:07 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-05-20 13:24 [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device Fabio Estevam
2019-05-20 13:24 ` [PATCH RESEND 2/2] ARM: dts: imx53-smd: Add OV5642 video capture support Fabio Estevam
2019-05-23 9:06 ` [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device Shawn Guo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).