linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: "Ondřej Jirman" <megous@megous.com>
To: Yangtao Li <tiny.windzz@gmail.com>
Cc: mark.rutland@arm.com, devicetree@vger.kernel.org,
	linux-pm@vger.kernel.org, maxime.ripard@bootlin.com,
	gregkh@linuxfoundation.org, linus.walleij@linaro.org,
	daniel.lezcano@linaro.org, linux-kernel@vger.kernel.org,
	edubezval@gmail.com, wens@csie.org, robh+dt@kernel.org,
	mchehab+samsung@kernel.org, rui.zhang@intel.com,
	paulmck@linux.ibm.com, davem@davemloft.net,
	linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v4 11/11] thermal: sun8i: add thermal driver for h3
Date: Mon, 24 Jun 2019 14:05:37 +0200	[thread overview]
Message-ID: <20190624120537.sxdm4y3jec3ksr4u@core.my.home> (raw)
In-Reply-To: <20190623164206.7467-12-tiny.windzz@gmail.com>

Hello Yangtao,

On Sun, Jun 23, 2019 at 12:42:06PM -0400, Yangtao Li wrote:
> This patch adds the support for allwinner h3 thermal sensor.
> 
> Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
> ---
>  drivers/thermal/sun8i_thermal.c | 72 +++++++++++++++++++++++++++++++++
>  1 file changed, 72 insertions(+)
> 
> diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
> index 260b24340f5b..c8ee291f3b17 100644
> --- a/drivers/thermal/sun8i_thermal.c
> +++ b/drivers/thermal/sun8i_thermal.c
> @@ -27,6 +27,14 @@
>  #define TEMP_TO_REG				672
>  #define CALIBRATE_DEFAULT			0x800
>  
> +#define SUN8I_THS_CTRL0				0x00
> +#define SUN8I_THS_CTRL2				0x40
> +#define SUN8I_THS_IC				0x44
> +#define SUN8I_THS_IS				0x48
> +#define SUN8I_THS_MFC				0x70
> +#define SUN8I_THS_TEMP_CALIB			0x74
> +#define SUN8I_THS_TEMP_DATA			0x80
> +
>  #define SUN50I_THS_CTRL0			0x00
>  #define SUN50I_H6_THS_ENABLE			0x04
>  #define SUN50I_H6_THS_PC			0x08
> @@ -36,6 +44,9 @@
>  #define SUN50I_H6_THS_TEMP_CALIB		0xa0
>  #define SUN50I_H6_THS_TEMP_DATA			0xc0
>  
> +#define SUN8I_THS_CTRL0_T_ACQ0(x)		(GENMASK(15, 0) & (x))
> +#define SUN8I_THS_CTRL2_T_ACQ1(x)		((GENMASK(15, 0) & (x)) << 16)
> +
>  #define SUN50I_THS_CTRL0_T_ACQ(x)		((GENMASK(15, 0) & (x)) << 16)
>  #define SUN50I_THS_FILTER_EN			BIT(2)
>  #define SUN50I_THS_FILTER_TYPE(x)		(GENMASK(1, 0) & (x))
> @@ -121,6 +132,21 @@ static const struct regmap_config config = {
>  	.fast_io = true,
>  };
>  
> +static int sun8i_h3_irq_ack(struct ths_device *tmdev)
> +{
> +	int state, ret = 0;
> +
> +	regmap_read(tmdev->regmap, SUN8I_THS_IS, &state);
> +
> +	if (state & BIT(8)) {
> +		regmap_write(tmdev->regmap, SUN8I_THS_IS,
> +			     BIT(8));
> +		ret |= BIT(1);
> +	}
> +
> +	return ret;
> +}
> +
>  static int sun50i_h6_irq_ack(struct ths_device *tmdev)
>  {
>  	int i, state, ret = 0;
> @@ -154,6 +180,14 @@ static irqreturn_t sun8i_irq_thread(int irq, void *data)
>  	return IRQ_HANDLED;
>  }
>  
> +static int sun8i_h3_ths_calibrate(struct ths_device *tmdev,
> +			       u16 *caldata, int callen)
> +{
> +	regmap_write(tmdev->regmap, SUN8I_THS_TEMP_CALIB, *caldata);

You're missing a sanity check for callen here.

regards,
	o.

> +	return 0;
> +}
> +
>  static int sun50i_h6_ths_calibrate(struct ths_device *tmdev,
>  				   u16 *caldata, int callen)
>  {
> @@ -325,6 +359,32 @@ static int sun8i_ths_resource_init(struct ths_device *tmdev)
>  	return ret;
>  }
>  
> +static int sun8i_h3_thermal_init(struct ths_device *tmdev)
> +{
> +	/* average over 4 samples */
> +	regmap_write(tmdev->regmap, SUN8I_THS_MFC,
> +		     SUN50I_THS_FILTER_EN |
> +		     SUN50I_THS_FILTER_TYPE(1));
> +	/*
> +	 * period = (x + 1) * 4096 / clkin; ~10ms
> +	 * enable data interrupt
> +	 */
> +	regmap_write(tmdev->regmap, SUN8I_THS_IC,
> +		     SUN50I_H6_THS_PC_TEMP_PERIOD(58) | BIT(8));
> +	/*
> +	 * clkin = 24MHz
> +	 * T acquire = clkin / (x + 1)
> +	 *           = 20us
> +	 * enable sensor
> +	 */
> +	regmap_write(tmdev->regmap, SUN8I_THS_CTRL0,
> +		     SUN8I_THS_CTRL0_T_ACQ0(479));
> +	regmap_write(tmdev->regmap, SUN8I_THS_CTRL2,
> +		     SUN8I_THS_CTRL2_T_ACQ1(479) | BIT(0));
> +
> +	return 0;
> +}
> +
>  static int sun50i_thermal_init(struct ths_device *tmdev)
>  {
>  	int val;
> @@ -431,6 +491,17 @@ static int sun8i_ths_remove(struct platform_device *pdev)
>  	return 0;
>  }
>  
> +static const struct ths_thermal_chip sun8i_h3_ths = {
> +	.sensor_num = 1,
> +	.offset = -1794,
> +	.scale = -121,
> +	.has_ahb_clk = true,
> +	.temp_data_base = SUN8I_THS_TEMP_DATA,
> +	.calibrate = sun8i_h3_ths_calibrate,
> +	.init = sun8i_h3_thermal_init,
> +	.irq_ack = sun8i_h3_irq_ack,
> +};
> +
>  static const struct ths_thermal_chip sun50i_h6_ths = {
>  	.sensor_num = 2,
>  	.offset = -2794,
> @@ -443,6 +514,7 @@ static const struct ths_thermal_chip sun50i_h6_ths = {
>  };
>  
>  static const struct of_device_id of_ths_match[] = {
> +	{ .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths },
>  	{ .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths },
>  	{ /* sentinel */ },
>  };
> -- 
> 2.17.1
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  reply	other threads:[~2019-06-24 12:05 UTC|newest]

Thread overview: 23+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-06-23 16:41 [PATCH v4 00/11] add thermal driver for h6 Yangtao Li
2019-06-23 16:41 ` [PATCH v4 01/11] thermal: sun8i: " Yangtao Li
2019-06-24 12:07   ` Ondřej Jirman
2019-06-23 16:41 ` [PATCH v4 02/11] dt-bindings: thermal: add binding document for h6 thermal controller Yangtao Li
2019-06-24  8:47   ` Maxime Ripard
2019-06-23 16:41 ` [PATCH v4 03/11] thermal: fix indentation in makefile Yangtao Li
2019-06-23 16:41 ` [PATCH v4 04/11] thermal: sun8i: get ths sensor number from device compatible Yangtao Li
2019-06-23 16:42 ` [PATCH v4 05/11] thermal: sun8i: rework for sun8i_ths_get_temp() Yangtao Li
2019-06-23 16:42 ` [PATCH v4 06/11] thermal: sun8i: get ths init func from device compatible Yangtao Li
2019-06-23 16:42 ` [PATCH v4 07/11] thermal: sun8i: rework for ths irq handler func Yangtao Li
2019-06-23 16:42 ` [PATCH v4 08/11] thermal: sun8i: support ahb clocks Yangtao Li
2019-06-24 18:23   ` Maxime Ripard
2019-06-25  0:34     ` Ondřej Jirman
2019-06-25  8:25       ` Maxime Ripard
2019-06-23 16:42 ` [PATCH v4 09/11] thermal: sun8i: rework for ths calibrate func Yangtao Li
2019-06-23 16:42 ` [PATCH v4 10/11] dt-bindings: thermal: add binding document for h3 thermal controller Yangtao Li
2019-06-24  8:50   ` Maxime Ripard
2019-06-23 16:42 ` [PATCH v4 11/11] thermal: sun8i: add thermal driver for h3 Yangtao Li
2019-06-24 12:05   ` Ondřej Jirman [this message]
2019-07-10 23:09 ` [PATCH v4 00/11] add thermal driver for h6 Vasily Khoruzhick
2019-07-13 18:01   ` Vasily Khoruzhick
2019-07-26 17:46     ` Vasily Khoruzhick
2019-07-28 12:11       ` Frank Lee

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190624120537.sxdm4y3jec3ksr4u@core.my.home \
    --to=megous@megous.com \
    --cc=daniel.lezcano@linaro.org \
    --cc=davem@davemloft.net \
    --cc=devicetree@vger.kernel.org \
    --cc=edubezval@gmail.com \
    --cc=gregkh@linuxfoundation.org \
    --cc=linus.walleij@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pm@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=maxime.ripard@bootlin.com \
    --cc=mchehab+samsung@kernel.org \
    --cc=paulmck@linux.ibm.com \
    --cc=robh+dt@kernel.org \
    --cc=rui.zhang@intel.com \
    --cc=tiny.windzz@gmail.com \
    --cc=wens@csie.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).