* [RESEND PATCH next v2 1/6] ARM: dts: keystone-clocks: add input fixed clocks
2019-07-05 15:12 [RESEND PATCH next v2 0/6] ARM: keystone: update dt and enable cpts support Grygorii Strashko
@ 2019-07-05 15:12 ` Grygorii Strashko
2019-07-05 15:12 ` [RESEND PATCH next v2 2/6] ARM: dts: k2e-clocks: add input ext. fixed clocks tsipclka/b Grygorii Strashko
` (5 subsequent siblings)
6 siblings, 0 replies; 11+ messages in thread
From: Grygorii Strashko @ 2019-07-05 15:12 UTC (permalink / raw)
To: Santosh Shilimkar
Cc: devicetree, Grygorii Strashko, Sekhar Nori, linux-kernel,
Murali Karicheri, linux-arm-kernel
Add set of fixed, external input clocks definitions for TIMI0, TIMI1,
TSREFCLK clocks. Such clocks can be used as reference clocks for some HW
modules (as cpts, for example) by configuring corresponding clock muxes.
For these clocks real frequencies have to be defined in board files.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
arch/arm/boot/dts/keystone-clocks.dtsi | 27 ++++++++++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/arch/arm/boot/dts/keystone-clocks.dtsi b/arch/arm/boot/dts/keystone-clocks.dtsi
index 457515b0736a..0397c3423d2d 100644
--- a/arch/arm/boot/dts/keystone-clocks.dtsi
+++ b/arch/arm/boot/dts/keystone-clocks.dtsi
@@ -408,4 +408,31 @@ clocks {
reg-names = "control", "domain";
domain-id = <0>;
};
+
+ /*
+ * Below are set of fixed, input clocks definitions,
+ * for which real frequencies have to be defined in board files.
+ * Those clocks can be used as reference clocks for some HW modules
+ * (as cpts, for example) by configuring corresponding clock muxes.
+ */
+ timi0: timi0 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <0>;
+ clock-output-names = "timi0";
+ };
+
+ timi1: timi1 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <0>;
+ clock-output-names = "timi1";
+ };
+
+ tsrefclk: tsrefclk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <0>;
+ clock-output-names = "tsrefclk";
+ };
};
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* [RESEND PATCH next v2 2/6] ARM: dts: k2e-clocks: add input ext. fixed clocks tsipclka/b
2019-07-05 15:12 [RESEND PATCH next v2 0/6] ARM: keystone: update dt and enable cpts support Grygorii Strashko
2019-07-05 15:12 ` [RESEND PATCH next v2 1/6] ARM: dts: keystone-clocks: add input fixed clocks Grygorii Strashko
@ 2019-07-05 15:12 ` Grygorii Strashko
2019-07-05 15:12 ` [RESEND PATCH next v2 3/6] ARM: dts: k2e-netcp: add cpts refclk_mux node Grygorii Strashko
` (4 subsequent siblings)
6 siblings, 0 replies; 11+ messages in thread
From: Grygorii Strashko @ 2019-07-05 15:12 UTC (permalink / raw)
To: Santosh Shilimkar
Cc: devicetree, Grygorii Strashko, Sekhar Nori, linux-kernel,
Murali Karicheri, linux-arm-kernel
Add set of fixed, external input clocks definitions for TSIPCLKA, TSIPCLKB
clocks. Such clocks can be used as reference clocks for some HW modules (as
cpts, for example) by configuring corresponding clock muxes. For these
clocks real frequencies have to be defined in board files.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
arch/arm/boot/dts/keystone-k2e-clocks.dtsi | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/boot/dts/keystone-k2e-clocks.dtsi b/arch/arm/boot/dts/keystone-k2e-clocks.dtsi
index f7592155a740..cf30e007fea3 100644
--- a/arch/arm/boot/dts/keystone-k2e-clocks.dtsi
+++ b/arch/arm/boot/dts/keystone-k2e-clocks.dtsi
@@ -71,4 +71,24 @@ clocks {
reg-names = "control", "domain";
domain-id = <29>;
};
+
+ /*
+ * Below are set of fixed, input clocks definitions,
+ * for which real frequencies have to be defined in board files.
+ * Those clocks can be used as reference clocks for some HW modules
+ * (as cpts, for example) by configuring corresponding clock muxes.
+ */
+ tsipclka: tsipclka {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <0>;
+ clock-output-names = "tsipclka";
+ };
+
+ tsipclkb: tsipclkb {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <0>;
+ clock-output-names = "tsipclkb";
+ };
};
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* [RESEND PATCH next v2 3/6] ARM: dts: k2e-netcp: add cpts refclk_mux node
2019-07-05 15:12 [RESEND PATCH next v2 0/6] ARM: keystone: update dt and enable cpts support Grygorii Strashko
2019-07-05 15:12 ` [RESEND PATCH next v2 1/6] ARM: dts: keystone-clocks: add input fixed clocks Grygorii Strashko
2019-07-05 15:12 ` [RESEND PATCH next v2 2/6] ARM: dts: k2e-clocks: add input ext. fixed clocks tsipclka/b Grygorii Strashko
@ 2019-07-05 15:12 ` Grygorii Strashko
2019-07-05 15:12 ` [RESEND PATCH next v2 4/6] ARM: dts: k2hk-netcp: " Grygorii Strashko
` (3 subsequent siblings)
6 siblings, 0 replies; 11+ messages in thread
From: Grygorii Strashko @ 2019-07-05 15:12 UTC (permalink / raw)
To: Santosh Shilimkar
Cc: devicetree, Grygorii Strashko, Sekhar Nori, linux-kernel,
Murali Karicheri, linux-arm-kernel
KeyStone 66AK2E 1G Ethernet Switch Subsystems, can control an external
multiplexer that selects one of up to 32 clocks for time sync reference
(RFTCLK) clock. This feature can be configured through CPTS_RFTCLK_SEL
register (offset: x08) in CPTS module and modelled as multiplexer clock.
Hence, add cpts-refclk-mux clock node which allows to mux one of SYSCLK2,
SYSCLK3, TIMI0, TIMI1, TSIPCLKA, TSREFCLK, TSIPCLKB clocks as CPTS
reference clock [1] and group all CPTS properties under "cpts" subnode.
[1] http://www.ti.com/lit/gpn/66ak2e05
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
arch/arm/boot/dts/keystone-k2e-netcp.dtsi | 21 +++++++++++++++++++--
1 file changed, 19 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/keystone-k2e-netcp.dtsi b/arch/arm/boot/dts/keystone-k2e-netcp.dtsi
index 1db17ec744b1..ad15e77874b1 100644
--- a/arch/arm/boot/dts/keystone-k2e-netcp.dtsi
+++ b/arch/arm/boot/dts/keystone-k2e-netcp.dtsi
@@ -135,8 +135,8 @@ netcp: netcp@24000000 {
/* NetCP address range */
ranges = <0 0x24000000 0x1000000>;
- clocks = <&clkpa>, <&clkcpgmac>, <&chipclk12>;
- clock-names = "pa_clk", "ethss_clk", "cpts";
+ clocks = <&clkpa>, <&clkcpgmac>;
+ clock-names = "pa_clk", "ethss_clk";
dma-coherent;
ti,navigator-dmas = <&dma_gbe 0>,
@@ -156,6 +156,23 @@ netcp: netcp@24000000 {
tx-queue = <896>;
tx-channel = "nettx";
+ cpts {
+ clocks = <&cpts_refclk_mux>;
+ clock-names = "cpts";
+
+ cpts_refclk_mux: cpts-refclk-mux {
+ #clock-cells = <0>;
+ clocks = <&chipclk12>, <&chipclk13>,
+ <&timi0>, <&timi1>,
+ <&tsipclka>, <&tsrefclk>,
+ <&tsipclkb>;
+ ti,mux-tbl = <0x0>, <0x1>, <0x2>,
+ <0x3>, <0x4>, <0x8>, <0xC>;
+ assigned-clocks = <&cpts_refclk_mux>;
+ assigned-clock-parents = <&chipclk12>;
+ };
+ };
+
interfaces {
gbe0: interface-0 {
slave-port = <0>;
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* [RESEND PATCH next v2 4/6] ARM: dts: k2hk-netcp: add cpts refclk_mux node
2019-07-05 15:12 [RESEND PATCH next v2 0/6] ARM: keystone: update dt and enable cpts support Grygorii Strashko
` (2 preceding siblings ...)
2019-07-05 15:12 ` [RESEND PATCH next v2 3/6] ARM: dts: k2e-netcp: add cpts refclk_mux node Grygorii Strashko
@ 2019-07-05 15:12 ` Grygorii Strashko
2019-07-05 15:12 ` [RESEND PATCH next v2 5/6] ARM: dts: k2l-netcp: " Grygorii Strashko
` (2 subsequent siblings)
6 siblings, 0 replies; 11+ messages in thread
From: Grygorii Strashko @ 2019-07-05 15:12 UTC (permalink / raw)
To: Santosh Shilimkar
Cc: devicetree, Grygorii Strashko, Sekhar Nori, linux-kernel,
Murali Karicheri, linux-arm-kernel
KeyStone 66AK2H/K 1G Ethernet Switch Subsystems, can control an external
multiplexer that selects one of up to 32 clocks for time sync reference
(RFTCLK) clock. This feature can be configured through CPTS_RFTCLK_SEL
register (offset: x08) in CPTS module and modelled as multiplexer clock.
Hence, add cpts-refclk-mux clock node which allows to mux one of SYSCLK2,
SYSCLK3, TIMI0, TIMI1, TSREFCLK clocks as CPTS reference clock [1] and
group all CPTS properties under "cpts" subnode.
[1] http://www.ti.com/lit/gpn/66ak2h14
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
arch/arm/boot/dts/keystone-k2hk-netcp.dtsi | 20 ++++++++++++++++++--
1 file changed, 18 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/keystone-k2hk-netcp.dtsi b/arch/arm/boot/dts/keystone-k2hk-netcp.dtsi
index e203145acbea..d5a6c1f5633c 100644
--- a/arch/arm/boot/dts/keystone-k2hk-netcp.dtsi
+++ b/arch/arm/boot/dts/keystone-k2hk-netcp.dtsi
@@ -152,8 +152,8 @@ netcp: netcp@2000000 {
/* NetCP address range */
ranges = <0 0x2000000 0x100000>;
- clocks = <&clkpa>, <&clkcpgmac>, <&chipclk12>;
- clock-names = "pa_clk", "ethss_clk", "cpts";
+ clocks = <&clkpa>, <&clkcpgmac>;
+ clock-names = "pa_clk", "ethss_clk";
dma-coherent;
ti,navigator-dmas = <&dma_gbe 22>,
@@ -175,6 +175,22 @@ netcp: netcp@2000000 {
tx-queue = <648>;
tx-channel = "nettx";
+ cpts {
+ clocks = <&cpts_refclk_mux>;
+ clock-names = "cpts";
+
+ cpts_refclk_mux: cpts-refclk-mux {
+ #clock-cells = <0>;
+ clocks = <&chipclk12>, <&chipclk13>,
+ <&timi0>, <&timi1>,
+ <&tsrefclk>;
+ ti,mux-tbl = <0x0>, <0x1>, <0x2>,
+ <0x3>, <0x8>;
+ assigned-clocks = <&cpts_refclk_mux>;
+ assigned-clock-parents = <&chipclk12>;
+ };
+ };
+
interfaces {
gbe0: interface-0 {
slave-port = <0>;
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* [RESEND PATCH next v2 5/6] ARM: dts: k2l-netcp: add cpts refclk_mux node
2019-07-05 15:12 [RESEND PATCH next v2 0/6] ARM: keystone: update dt and enable cpts support Grygorii Strashko
` (3 preceding siblings ...)
2019-07-05 15:12 ` [RESEND PATCH next v2 4/6] ARM: dts: k2hk-netcp: " Grygorii Strashko
@ 2019-07-05 15:12 ` Grygorii Strashko
2019-07-05 15:12 ` [RESEND PATCH next v2 6/6] ARM: configs: keystone: enable cpts Grygorii Strashko
2019-07-05 23:48 ` [RESEND PATCH next v2 0/6] ARM: keystone: update dt and enable cpts support santosh.shilimkar
6 siblings, 0 replies; 11+ messages in thread
From: Grygorii Strashko @ 2019-07-05 15:12 UTC (permalink / raw)
To: Santosh Shilimkar
Cc: devicetree, Grygorii Strashko, Sekhar Nori, linux-kernel,
Murali Karicheri, linux-arm-kernel
KeyStone 66AK2L 1G Ethernet Switch Subsystems, can control an external
multiplexer that selects one of up to 32 clocks for time sync reference
(RFTCLK) clock. This feature can be configured through CPTS_RFTCLK_SEL
register (offset: x08) in CPTS module and modelled as multiplexer clock.
Hence, add cpts-refclk-mux clock node which allows to mux one of SYSCLK2,
SYSCLK3, TIMI0, TIMI1, TSREFCLK clocks as CPTS
reference clock [1] and group all CPTS properties under "cpts" subnode.
[1] http://www.ti.com/lit/gpn/66ak2l06
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
arch/arm/boot/dts/keystone-k2l-netcp.dtsi | 20 ++++++++++++++++++--
1 file changed, 18 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/keystone-k2l-netcp.dtsi b/arch/arm/boot/dts/keystone-k2l-netcp.dtsi
index a2e47bad3307..c1f982604145 100644
--- a/arch/arm/boot/dts/keystone-k2l-netcp.dtsi
+++ b/arch/arm/boot/dts/keystone-k2l-netcp.dtsi
@@ -134,8 +134,8 @@ netcp: netcp@26000000 {
/* NetCP address range */
ranges = <0 0x26000000 0x1000000>;
- clocks = <&clkpa>, <&clkcpgmac>, <&chipclk12>;
- clock-names = "pa_clk", "ethss_clk", "cpts";
+ clocks = <&clkpa>, <&clkcpgmac>;
+ clock-names = "pa_clk", "ethss_clk";
dma-coherent;
ti,navigator-dmas = <&dma_gbe 0>,
@@ -155,6 +155,22 @@ netcp: netcp@26000000 {
tx-queue = <896>;
tx-channel = "nettx";
+ cpts {
+ clocks = <&cpts_refclk_mux>;
+ clock-names = "cpts";
+
+ cpts_refclk_mux: cpts-refclk-mux {
+ #clock-cells = <0>;
+ clocks = <&chipclk12>, <&chipclk13>,
+ <&timi0>, <&timi1>,
+ <&tsrefclk>;
+ ti,mux-tbl = <0x0>, <0x1>, <0x2>,
+ <0x3>, <0x8>;
+ assigned-clocks = <&cpts_refclk_mux>;
+ assigned-clock-parents = <&chipclk12>;
+ };
+ };
+
interfaces {
gbe0: interface-0 {
slave-port = <0>;
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* [RESEND PATCH next v2 6/6] ARM: configs: keystone: enable cpts
2019-07-05 15:12 [RESEND PATCH next v2 0/6] ARM: keystone: update dt and enable cpts support Grygorii Strashko
` (4 preceding siblings ...)
2019-07-05 15:12 ` [RESEND PATCH next v2 5/6] ARM: dts: k2l-netcp: " Grygorii Strashko
@ 2019-07-05 15:12 ` Grygorii Strashko
2019-07-05 23:48 ` [RESEND PATCH next v2 0/6] ARM: keystone: update dt and enable cpts support santosh.shilimkar
6 siblings, 0 replies; 11+ messages in thread
From: Grygorii Strashko @ 2019-07-05 15:12 UTC (permalink / raw)
To: Santosh Shilimkar
Cc: devicetree, Grygorii Strashko, Sekhar Nori, linux-kernel,
Murali Karicheri, linux-arm-kernel
Enable CPTS support which is present in Network Coprocessor Gigabit
Ethernet (GbE) Switch Subsystem.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
arch/arm/configs/keystone_defconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/configs/keystone_defconfig b/arch/arm/configs/keystone_defconfig
index 72fee57aad2f..0b2281407ecf 100644
--- a/arch/arm/configs/keystone_defconfig
+++ b/arch/arm/configs/keystone_defconfig
@@ -136,6 +136,7 @@ CONFIG_BLK_DEV_SD=y
CONFIG_NETDEVICES=y
CONFIG_TI_KEYSTONE_NETCP=y
CONFIG_TI_KEYSTONE_NETCP_ETHSS=y
+CONFIG_TI_CPTS=y
CONFIG_MARVELL_PHY=y
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread* Re: [RESEND PATCH next v2 0/6] ARM: keystone: update dt and enable cpts support
2019-07-05 15:12 [RESEND PATCH next v2 0/6] ARM: keystone: update dt and enable cpts support Grygorii Strashko
` (5 preceding siblings ...)
2019-07-05 15:12 ` [RESEND PATCH next v2 6/6] ARM: configs: keystone: enable cpts Grygorii Strashko
@ 2019-07-05 23:48 ` santosh.shilimkar
2019-07-16 10:44 ` grygorii
2019-09-05 19:33 ` Grygorii Strashko
6 siblings, 2 replies; 11+ messages in thread
From: santosh.shilimkar @ 2019-07-05 23:48 UTC (permalink / raw)
To: Grygorii Strashko, Santosh Shilimkar
Cc: devicetree, Murali Karicheri, Sekhar Nori, linux-kernel,
linux-arm-kernel
On 7/5/19 8:12 AM, Grygorii Strashko wrote:
> Hi Santosh,
>
> This series is set of platform changes required to enable NETCP CPTS reference
> clock selection and final patch to enable CPTS for Keystone 66AK2E/L/HK SoCs.
>
> Those patches were posted already [1] together with driver's changes, so this
> is re-send of DT/platform specific changes only, as driver's changes have
> been merged already.
>
> Patches 1-5: CPTS DT nodes update for TI Keystone 2 66AK2HK/E/L SoCs.
> Patch 6: enables CPTS for TI Keystone 2 66AK2HK/E/L SoCs.
>
> [1] https://patchwork.kernel.org/cover/10980037/
>
> Grygorii Strashko (6):
> ARM: dts: keystone-clocks: add input fixed clocks
> ARM: dts: k2e-clocks: add input ext. fixed clocks tsipclka/b
> ARM: dts: k2e-netcp: add cpts refclk_mux node
> ARM: dts: k2hk-netcp: add cpts refclk_mux node
> ARM: dts: k2l-netcp: add cpts refclk_mux node
> ARM: configs: keystone: enable cpts
>
Will add these for 5.4 queue. Thanks !!
Regards,
Santosh
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 11+ messages in thread* Re: [RESEND PATCH next v2 0/6] ARM: keystone: update dt and enable cpts support
2019-07-05 23:48 ` [RESEND PATCH next v2 0/6] ARM: keystone: update dt and enable cpts support santosh.shilimkar
@ 2019-07-16 10:44 ` grygorii
2019-09-05 19:33 ` Grygorii Strashko
1 sibling, 0 replies; 11+ messages in thread
From: grygorii @ 2019-07-16 10:44 UTC (permalink / raw)
To: santosh.shilimkar, Santosh Shilimkar
Cc: devicetree, Murali Karicheri, Sekhar Nori, linux-kernel,
linux-arm-kernel
On 06/07/2019 05:18, santosh.shilimkar@oracle.com wrote:
> On 7/5/19 8:12 AM, Grygorii Strashko wrote:
>> Hi Santosh,
>>
>> This series is set of platform changes required to enable NETCP CPTS reference
>> clock selection and final patch to enable CPTS for Keystone 66AK2E/L/HK SoCs.
>>
>> Those patches were posted already [1] together with driver's changes, so this
>> is re-send of DT/platform specific changes only, as driver's changes have
>> been merged already.
>>
>> Patches 1-5: CPTS DT nodes update for TI Keystone 2 66AK2HK/E/L SoCs.
>> Patch 6: enables CPTS for TI Keystone 2 66AK2HK/E/L SoCs.
>>
>> [1] https://patchwork.kernel.org/cover/10980037/
>>
>> Grygorii Strashko (6):
>> ARM: dts: keystone-clocks: add input fixed clocks
>> ARM: dts: k2e-clocks: add input ext. fixed clocks tsipclka/b
>> ARM: dts: k2e-netcp: add cpts refclk_mux node
>> ARM: dts: k2hk-netcp: add cpts refclk_mux node
>> ARM: dts: k2l-netcp: add cpts refclk_mux node
>> ARM: configs: keystone: enable cpts
>>
> Will add these for 5.4 queue. Thanks !!
Thank you
--
Best regards,
grygorii
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [RESEND PATCH next v2 0/6] ARM: keystone: update dt and enable cpts support
2019-07-05 23:48 ` [RESEND PATCH next v2 0/6] ARM: keystone: update dt and enable cpts support santosh.shilimkar
2019-07-16 10:44 ` grygorii
@ 2019-09-05 19:33 ` Grygorii Strashko
2019-09-06 4:52 ` santosh.shilimkar
1 sibling, 1 reply; 11+ messages in thread
From: Grygorii Strashko @ 2019-09-05 19:33 UTC (permalink / raw)
To: santosh.shilimkar, Santosh Shilimkar
Cc: devicetree, Murali Karicheri, Sekhar Nori, linux-kernel,
linux-arm-kernel
Hi Santosh,
On 06/07/2019 02:48, santosh.shilimkar@oracle.com wrote:
> On 7/5/19 8:12 AM, Grygorii Strashko wrote:
>> Hi Santosh,
>>
>> This series is set of platform changes required to enable NETCP CPTS reference
>> clock selection and final patch to enable CPTS for Keystone 66AK2E/L/HK SoCs.
>>
>> Those patches were posted already [1] together with driver's changes, so this
>> is re-send of DT/platform specific changes only, as driver's changes have
>> been merged already.
>>
>> Patches 1-5: CPTS DT nodes update for TI Keystone 2 66AK2HK/E/L SoCs.
>> Patch 6: enables CPTS for TI Keystone 2 66AK2HK/E/L SoCs.
>>
>> [1] https://patchwork.kernel.org/cover/10980037/
>>
>> Grygorii Strashko (6):
>> ARM: dts: keystone-clocks: add input fixed clocks
>> ARM: dts: k2e-clocks: add input ext. fixed clocks tsipclka/b
>> ARM: dts: k2e-netcp: add cpts refclk_mux node
>> ARM: dts: k2hk-netcp: add cpts refclk_mux node
>> ARM: dts: k2l-netcp: add cpts refclk_mux node
>> ARM: configs: keystone: enable cpts
>>
> Will add these for 5.4 queue. Thanks !!
Sry, that I'm disturbing you, but I do not see those patches applied?
--
Best regards,
grygorii
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [RESEND PATCH next v2 0/6] ARM: keystone: update dt and enable cpts support
2019-09-05 19:33 ` Grygorii Strashko
@ 2019-09-06 4:52 ` santosh.shilimkar
0 siblings, 0 replies; 11+ messages in thread
From: santosh.shilimkar @ 2019-09-06 4:52 UTC (permalink / raw)
To: Grygorii Strashko, Santosh Shilimkar
Cc: devicetree, Murali Karicheri, Sekhar Nori, linux-kernel,
linux-arm-kernel
On 9/5/19 12:33 PM, Grygorii Strashko wrote:
> Hi Santosh,
>
> On 06/07/2019 02:48, santosh.shilimkar@oracle.com wrote:
>> On 7/5/19 8:12 AM, Grygorii Strashko wrote:
>>> Hi Santosh,
>>>
>>> This series is set of platform changes required to enable NETCP CPTS
>>> reference
>>> clock selection and final patch to enable CPTS for Keystone
>>> 66AK2E/L/HK SoCs.
>>>
>>> Those patches were posted already [1] together with driver's changes,
>>> so this
>>> is re-send of DT/platform specific changes only, as driver's changes
>>> have
>>> been merged already.
>>>
>>> Patches 1-5: CPTS DT nodes update for TI Keystone 2 66AK2HK/E/L SoCs.
>>> Patch 6: enables CPTS for TI Keystone 2 66AK2HK/E/L SoCs.
>>>
>>> [1] https://patchwork.kernel.org/cover/10980037/
>>>
>>> Grygorii Strashko (6):
>>> ARM: dts: keystone-clocks: add input fixed clocks
>>> ARM: dts: k2e-clocks: add input ext. fixed clocks tsipclka/b
>>> ARM: dts: k2e-netcp: add cpts refclk_mux node
>>> ARM: dts: k2hk-netcp: add cpts refclk_mux node
>>> ARM: dts: k2l-netcp: add cpts refclk_mux node
>>> ARM: configs: keystone: enable cpts
>>>
>> Will add these for 5.4 queue. Thanks !!
>
> Sry, that I'm disturbing you, but I do not see those patches applied?
>
Sorry I missed this one. Will queue this up for next merge window.
Will push this out to next early once rc1 is out. If you don't
see it, please ping me.
Regards,
Santosh
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 11+ messages in thread