* [V4, 0/2] media: i2c: Add support for OV02A10 sensor
@ 2019-09-07 9:27 dongchun.zhu
2019-09-07 9:27 ` [V4, 1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10 dongchun.zhu
2019-09-07 9:27 ` [V4, 2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver dongchun.zhu
0 siblings, 2 replies; 12+ messages in thread
From: dongchun.zhu @ 2019-09-07 9:27 UTC (permalink / raw)
To: mchehab, andriy.shevchenko, robh+dt, mark.rutland, sakari.ailus,
drinkcat, tfiga, matthias.bgg, bingbu.cao
Cc: devicetree, srv_heupstream, shengnan.wang, sj.huang,
linux-mediatek, dongchun.zhu, louis.kuo, linux-arm-kernel,
linux-media
From: Dongchun Zhu <dongchun.zhu@mediatek.com>
Hello,
This patch adds driver and bindings for Omnivision's OV02A10 2 megapixel CMOS 1/5" sensor,
which has a single MIPI lane interface and output format of 10-bit Raw.
The driver is implemented wth V4L2 framework.
1. Async registered as a V4L2 I2C sub-device.
2. A media entity that can provide several source pads and sink pads to link with other device like Seninf, ISP one after another
to create a default overall camera topology, image frame or meta-data from sensor can flow through particular path to output
preview or capture image or 3A info.
Changes of v4 mainly address the comments from Sakari, Rob, Tomasz.
- Remove data-lanes property in DT
- Add link frequencies in DT to match the expect value that driver requires
- Omit open callback as int_cfg is implemented
- Use i2c_smbus_write_byte_data/i2c_smbus_read_byte_data instead of customed APIs
- Use do_div to calculate pixel rate
- Use usleep_range directly for shoter sleep case
- Re-adjust sensor power up/off sequence
- Re-set pd/rst GPIO inverter property according to the datasheet
- Refine set_exposure/set_gain/set_vblanking/set_test_pattern functions
- Fix other reviewed issues in v3
Changes of v3 are mainly addressing comments from Rob, Sakari, Bingbu.
- Fix coding style errors in dt-bindings
- Use macro flag to describle basic line 1224 when updating v-blanking
- Remove unnecessary debug log in driver
Mainly changes of v2 are addressing the comments from Nicolas, Bingbu, Sakari, Rob,
including,
- Put dt binding before driver in series
- Add MAINTAINERS entries
- Squash the MAINTAINERS entry and Kconfig to driver patch
- Add rotation support for driver
- Fix other reviewed issues in v1
Dongchun Zhu (2):
media: dt-bindings: media: i2c: Add bindings for OV02A10
media: i2c: Add Omnivision OV02A10 camera sensor driver
.../devicetree/bindings/media/i2c/ov02a10.txt | 54 +
MAINTAINERS | 8 +
drivers/media/i2c/Kconfig | 11 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/ov02a10.c | 1062 ++++++++++++++++++++
5 files changed, 1136 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/ov02a10.txt
create mode 100644 drivers/media/i2c/ov02a10.c
--
2.9.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* [V4, 1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10
2019-09-07 9:27 [V4, 0/2] media: i2c: Add support for OV02A10 sensor dongchun.zhu
@ 2019-09-07 9:27 ` dongchun.zhu
2019-09-09 6:46 ` Sakari Ailus
2019-09-09 9:45 ` Andy Shevchenko
2019-09-07 9:27 ` [V4, 2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver dongchun.zhu
1 sibling, 2 replies; 12+ messages in thread
From: dongchun.zhu @ 2019-09-07 9:27 UTC (permalink / raw)
To: mchehab, andriy.shevchenko, robh+dt, mark.rutland, sakari.ailus,
drinkcat, tfiga, matthias.bgg, bingbu.cao
Cc: devicetree, srv_heupstream, shengnan.wang, sj.huang,
linux-mediatek, dongchun.zhu, louis.kuo, linux-arm-kernel,
linux-media
From: Dongchun Zhu <dongchun.zhu@mediatek.com>
This patch adds device tree bindings documentation for OV02A10 camera sensor.
Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
---
.../devicetree/bindings/media/i2c/ov02a10.txt | 54 ++++++++++++++++++++++
MAINTAINERS | 7 +++
2 files changed, 61 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/ov02a10.txt
diff --git a/Documentation/devicetree/bindings/media/i2c/ov02a10.txt b/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
new file mode 100644
index 0000000..18acc4f
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
@@ -0,0 +1,54 @@
+* Omnivision OV02A10 MIPI CSI-2 sensor
+
+Required Properties:
+- compatible: shall be "ovti,ov02a10"
+- clocks: reference to the eclk input clock
+- clock-names: shall be "eclk"
+- dovdd-supply: Digital I/O voltage supply, 1.8 volts
+- avdd-supply: Analog voltage supply, 2.8 volts
+- dvdd-supply: Digital core voltage supply, 1.8 volts
+- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
+ if any. This is an active low signal to the OV02A10.
+- reset-gpios: reference to the GPIO connected to the reset pin, if any.
+ This is an active high signal to the OV02A10.
+
+Optional Properties:
+- rotation: as defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt,
+ valid values are 0 (sensor mounted upright) and 180 (sensor
+ mounted upside down).
+
+The device node shall contain one 'port' child node with an
+'endpoint' subnode for its digital output video port,
+in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+&i2c4 {
+ ov02a10: camera-sensor@3d {
+ compatible = "ovti,ov02a10";
+ reg = <0x3d>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&camera_pins_cam1_mclk_on>;
+
+ clocks = <&topckgen CLK_TOP_MUX_CAMTG2>,
+ <&topckgen CLK_TOP_UNIVP_192M_D8>;
+ clock-names = "eclk", "freq_mux";
+ clock-frequency = <24000000>;
+
+ dovdd-supply = <&mt6358_vcamio_reg>;
+ avdd-supply = <&mt6358_vcama1_reg>;
+ dvdd-supply = <&mt6358_vcn18_reg>;
+ powerdown-gpios = <&pio 107 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&pio 109 GPIO_ACTIVE_HIGH>;
+ rotation = <180>;
+
+ port {
+ /* MIPI CSI-2 bus endpoint */
+ ov02a10_core: endpoint {
+ remote-endpoint = <&ov02a10_0>;
+ link-frequencies = /bits/ 64 <390000000>;
+ };
+ };
+ };
+};
diff --git a/MAINTAINERS b/MAINTAINERS
index 783569e..41734fb 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11816,6 +11816,13 @@ T: git git://linuxtv.org/media_tree.git
S: Maintained
F: drivers/media/i2c/ov13858.c
+OMNIVISION OV02A10 SENSOR DRIVER
+M: Dongchun Zhu <dongchun.zhu@mediatek.com>
+L: linux-media@vger.kernel.org
+T: git git://linuxtv.org/media_tree.git
+S: Maintained
+F: Documentation/devicetree/bindings/media/i2c/ov02a10.txt
+
OMNIVISION OV2680 SENSOR DRIVER
M: Rui Miguel Silva <rmfrfs@gmail.com>
L: linux-media@vger.kernel.org
--
2.9.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [V4, 2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver
2019-09-07 9:27 [V4, 0/2] media: i2c: Add support for OV02A10 sensor dongchun.zhu
2019-09-07 9:27 ` [V4, 1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10 dongchun.zhu
@ 2019-09-07 9:27 ` dongchun.zhu
2019-09-08 2:00 ` kbuild test robot
` (3 more replies)
1 sibling, 4 replies; 12+ messages in thread
From: dongchun.zhu @ 2019-09-07 9:27 UTC (permalink / raw)
To: mchehab, andriy.shevchenko, robh+dt, mark.rutland, sakari.ailus,
drinkcat, tfiga, matthias.bgg, bingbu.cao
Cc: devicetree, srv_heupstream, shengnan.wang, sj.huang,
linux-mediatek, dongchun.zhu, louis.kuo, linux-arm-kernel,
linux-media
From: Dongchun Zhu <dongchun.zhu@mediatek.com>
This patch adds a V4L2 sub-device driver for OV02A10 image sensor.
The OV02A10 is a 1/5" CMOS sensor from Omnivision,
supporting output format: 10-bit Raw.
The OV02A10 has a single MIPI lane interface and use the I2C bus
for control and the CSI-2 bus for data.
Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
---
MAINTAINERS | 1 +
drivers/media/i2c/Kconfig | 11 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/ov02a10.c | 1062 +++++++++++++++++++++++++++++++++++++++++++
4 files changed, 1075 insertions(+)
create mode 100644 drivers/media/i2c/ov02a10.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 41734fb..4b714a2 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11821,6 +11821,7 @@ M: Dongchun Zhu <dongchun.zhu@mediatek.com>
L: linux-media@vger.kernel.org
T: git git://linuxtv.org/media_tree.git
S: Maintained
+F: drivers/media/i2c/ov02a10.c
F: Documentation/devicetree/bindings/media/i2c/ov02a10.txt
OMNIVISION OV2680 SENSOR DRIVER
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 79ce9ec..22e0db4 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -617,6 +617,17 @@ config VIDEO_IMX355
To compile this driver as a module, choose M here: the
module will be called imx355.
+config VIDEO_OV02A10
+ tristate "OmniVision OV02A10 sensor support"
+ depends on VIDEO_V4L2 && I2C
+ depends on MEDIA_CAMERA_SUPPORT
+ help
+ This is a Video4Linux2 sensor driver for the OmniVision
+ OV02A10 camera.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ov02a10.
+
config VIDEO_OV2640
tristate "OmniVision OV2640 sensor support"
depends on VIDEO_V4L2 && I2C
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index fd4ea86..d27f4e2 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -63,6 +63,7 @@ obj-$(CONFIG_VIDEO_VP27SMPX) += vp27smpx.o
obj-$(CONFIG_VIDEO_SONY_BTF_MPX) += sony-btf-mpx.o
obj-$(CONFIG_VIDEO_UPD64031A) += upd64031a.o
obj-$(CONFIG_VIDEO_UPD64083) += upd64083.o
+obj-$(CONFIG_VIDEO_OV02A10) += ov02a10.o
obj-$(CONFIG_VIDEO_OV2640) += ov2640.o
obj-$(CONFIG_VIDEO_OV2680) += ov2680.o
obj-$(CONFIG_VIDEO_OV2685) += ov2685.o
diff --git a/drivers/media/i2c/ov02a10.c b/drivers/media/i2c/ov02a10.c
new file mode 100644
index 0000000..fb677d5
--- /dev/null
+++ b/drivers/media/i2c/ov02a10.c
@@ -0,0 +1,1062 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2019 MediaTek Inc.
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
+#include <media/media-entity.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-subdev.h>
+#include <media/v4l2-fwnode.h>
+
+#define CHIP_ID 0x2509
+#define OV02A10_REG_CHIP_ID_H 0x02
+#define OV02A10_REG_CHIP_ID_L 0x03
+#define OV02A10_ID(_msb, _lsb) ((_msb) << 8 | (_lsb))
+
+/* Bit[1] vertical upside down */
+/* Bit[0] horizontal mirror */
+#define REG_MIRROR_FLIP_CONTROL 0x3f
+
+/* Orientation */
+#define REG_MIRROR_FLIP_ENABLE 0x03
+
+#define REG_PAGE_SWITCH 0xfd
+#define REG_GLOBAL_EFFECTIVE 0x01
+#define REG_ENABLE BIT(0)
+#define OV02A10_MASK_8_BITS 0xff
+
+#define REG_SC_CTRL_MODE 0xac
+#define SC_CTRL_MODE_STANDBY 0x00
+#define SC_CTRL_MODE_STREAMING 0x01
+
+#define OV02A10_EXP_SHIFT 8
+#define OV02A10_REG_EXPOSURE_H 0x03
+#define OV02A10_REG_EXPOSURE_L 0x04
+#define OV02A10_EXPOSURE_MIN 4
+#define OV02A10_EXPOSURE_MAX_MARGIN 4
+#define OV02A10_EXPOSURE_STEP 1
+
+#define OV02A10_VTS_SHIFT 8
+#define OV02A10_REG_VTS_H 0x05
+#define OV02A10_REG_VTS_L 0x06
+#define OV02A10_VTS_MAX 0x209f
+#define OV02A10_VTS_MIN 0x04cf
+#define OV02A10_BASIC_LINE 1224
+
+#define OV02A10_REG_GAIN 0x24
+#define OV02A10_GAIN_MIN 0x10
+#define OV02A10_GAIN_MAX 0xf8
+#define OV02A10_GAIN_STEP 0x01
+#define OV02A10_GAIN_DEFAULT 0x40
+
+/* Test pattern control */
+#define OV02A10_REG_TEST_PATTERN 0xb6
+#define OV02A10_TEST_PATTERN_ENABLE BIT(0)
+
+#define OV02A10_LINK_FREQ_390MHZ 390000000ULL
+#define OV02A10_ECLK_FREQ 24000000
+#define OV02A10_DATA_LANES 1
+#define OV02A10_BITS_PER_SAMPLE 10
+
+static const char * const ov02a10_supply_names[] = {
+ "dovdd", /* Digital I/O power */
+ "avdd", /* Analog power */
+ "dvdd", /* Digital core power */
+};
+
+#define OV02A10_NUM_SUPPLIES ARRAY_SIZE(ov02a10_supply_names)
+
+struct ov02a10_reg {
+ u8 addr;
+ u8 val;
+};
+
+struct ov02a10_reg_list {
+ u32 num_of_regs;
+ const struct ov02a10_reg *regs;
+};
+
+struct ov02a10_mode {
+ u32 width;
+ u32 height;
+ u32 exp_def;
+ u32 hts_def;
+ u32 vts_def;
+ const struct ov02a10_reg_list reg_list;
+};
+
+struct ov02a10 {
+ struct clk *eclk;
+ u32 eclk_freq;
+
+ struct gpio_desc *pd_gpio;
+ struct gpio_desc *n_rst_gpio;
+ struct regulator_bulk_data supplies[OV02A10_NUM_SUPPLIES];
+
+ bool streaming;
+ bool upside_down;
+
+ /*
+ * Serialize control access, get/set format, get selection
+ * and start streaming.
+ */
+ struct mutex mutex;
+ struct v4l2_subdev subdev;
+ struct media_pad pad;
+ struct v4l2_ctrl *anal_gain;
+ struct v4l2_ctrl *exposure;
+ struct v4l2_ctrl *hblank;
+ struct v4l2_ctrl *vblank;
+ struct v4l2_ctrl *hflip;
+ struct v4l2_ctrl *vflip;
+ struct v4l2_ctrl *test_pattern;
+ struct v4l2_mbus_framefmt fmt;
+ struct v4l2_ctrl_handler ctrl_handler;
+
+ const struct ov02a10_mode *cur_mode;
+};
+
+static inline struct ov02a10 *to_ov02a10(struct v4l2_subdev *sd)
+{
+ return container_of(sd, struct ov02a10, subdev);
+}
+
+/*
+ * eclk 24Mhz
+ * pclk 39Mhz
+ * linelength 934(0x3a6)
+ * framelength 1390(0x56E)
+ * grabwindow_width 1600
+ * grabwindow_height 1200
+ * max_framerate 30fps
+ * mipi_datarate per lane 780Mbps
+ */
+static const struct ov02a10_reg ov02a10_1600x1200_regs[] = {
+ {0xfd, 0x01},
+ {0xac, 0x00},
+ {0xfd, 0x00},
+ {0x2f, 0x29},
+ {0x34, 0x00},
+ {0x35, 0x21},
+ {0x30, 0x15},
+ {0x33, 0x01},
+ {0xfd, 0x01},
+ {0x44, 0x00},
+ {0x2a, 0x4c},
+ {0x2b, 0x1e},
+ {0x2c, 0x60},
+ {0x25, 0x11},
+ {0x03, 0x01},
+ {0x04, 0xae},
+ {0x09, 0x00},
+ {0x0a, 0x02},
+ {0x06, 0xa6},
+ {0x31, 0x00},
+ {0x24, 0x40},
+ {0x01, 0x01},
+ {0xfb, 0x73},
+ {0xfd, 0x01},
+ {0x16, 0x04},
+ {0x1c, 0x09},
+ {0x21, 0x42},
+ {0x12, 0x04},
+ {0x13, 0x10},
+ {0x11, 0x40},
+ {0x33, 0x81},
+ {0xd0, 0x00},
+ {0xd1, 0x01},
+ {0xd2, 0x00},
+ {0x50, 0x10},
+ {0x51, 0x23},
+ {0x52, 0x20},
+ {0x53, 0x10},
+ {0x54, 0x02},
+ {0x55, 0x20},
+ {0x56, 0x02},
+ {0x58, 0x48},
+ {0x5d, 0x15},
+ {0x5e, 0x05},
+ {0x66, 0x66},
+ {0x68, 0x68},
+ {0x6b, 0x00},
+ {0x6c, 0x00},
+ {0x6f, 0x40},
+ {0x70, 0x40},
+ {0x71, 0x0a},
+ {0x72, 0xf0},
+ {0x73, 0x10},
+ {0x75, 0x80},
+ {0x76, 0x10},
+ {0x84, 0x00},
+ {0x85, 0x10},
+ {0x86, 0x10},
+ {0x87, 0x00},
+ {0x8a, 0x22},
+ {0x8b, 0x22},
+ {0x19, 0xf1},
+ {0x29, 0x01},
+ {0xfd, 0x01},
+ {0x9d, 0xd6},
+ {0xa0, 0x29},
+ {0xa1, 0x03},
+ {0xad, 0x62},
+ {0xae, 0x00},
+ {0xaf, 0x85},
+ {0xb1, 0x01},
+ {0x8e, 0x06},
+ {0x8f, 0x40},
+ {0x90, 0x04},
+ {0x91, 0xb0},
+ {0x45, 0x01},
+ {0x46, 0x00},
+ {0x47, 0x6c},
+ {0x48, 0x03},
+ {0x49, 0x8b},
+ {0x4a, 0x00},
+ {0x4b, 0x07},
+ {0x4c, 0x04},
+ {0x4d, 0xb7},
+ {0xf0, 0x40},
+ {0xf1, 0x40},
+ {0xf2, 0x40},
+ {0xf3, 0x40},
+ {0x3f, 0x00},
+ {0xfd, 0x01},
+ {0x05, 0x00},
+ {0x06, 0xa6},
+ {0xfd, 0x01},
+};
+
+static const char * const ov02a10_test_pattern_menu[] = {
+ "Disabled",
+ "Color Bar",
+};
+
+static const s64 link_freq_menu_items[] = {
+ OV02A10_LINK_FREQ_390MHZ
+};
+
+static u64 to_pixel_rate(u32 f_index)
+{
+ u64 pixel_rate = link_freq_menu_items[f_index] * 2 * OV02A10_DATA_LANES;
+
+ do_div(pixel_rate, OV02A10_BITS_PER_SAMPLE);
+
+ return pixel_rate;
+}
+
+static const struct ov02a10_mode supported_modes[] = {
+ {
+ .width = 1600,
+ .height = 1200,
+ .exp_def = 0x01ae,
+ .hts_def = 0x03a6,
+ .vts_def = 0x056e,
+ .reg_list = {
+ .num_of_regs = ARRAY_SIZE(ov02a10_1600x1200_regs),
+ .regs = ov02a10_1600x1200_regs,
+ },
+ },
+};
+
+static int ov02a10_write_array(struct ov02a10 *ov02a10,
+ const struct ov02a10_reg_list *r_list)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+ unsigned int i;
+ int ret;
+
+ for (i = 0; i < r_list->num_of_regs; i++) {
+ ret = i2c_smbus_write_byte_data(client,
+ r_list->regs[i].addr,
+ r_list->regs[i].val);
+ if (ret < 0)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int ov02a10_read_smbus(struct ov02a10 *ov02a10, unsigned char reg,
+ unsigned char *val)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+ int ret;
+
+ ret = i2c_smbus_read_byte_data(client, reg);
+ if (ret >= 0) {
+ *val = (unsigned char)ret;
+ ret = 0;
+ }
+
+ return ret;
+}
+
+static void ov02a10_fill_fmt(const struct ov02a10_mode *mode,
+ struct v4l2_mbus_framefmt *fmt)
+{
+ fmt->width = mode->width;
+ fmt->height = mode->height;
+ fmt->field = V4L2_FIELD_NONE;
+}
+
+static int ov02a10_set_fmt(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_format *fmt)
+{
+ struct ov02a10 *ov02a10 = to_ov02a10(sd);
+ struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
+
+ mutex_lock(&ov02a10->mutex);
+
+ if (ov02a10->streaming) {
+ mutex_unlock(&ov02a10->mutex);
+ return -EBUSY;
+ }
+
+ /* Only one sensor mode supported */
+ mbus_fmt->code = ov02a10->fmt.code;
+ ov02a10_fill_fmt(ov02a10->cur_mode, mbus_fmt);
+ ov02a10->fmt = fmt->format;
+
+ mutex_unlock(&ov02a10->mutex);
+
+ return 0;
+}
+
+static int ov02a10_get_fmt(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_format *fmt)
+{
+ struct ov02a10 *ov02a10 = to_ov02a10(sd);
+ struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
+
+ mutex_lock(&ov02a10->mutex);
+
+ fmt->format = ov02a10->fmt;
+ mbus_fmt->code = ov02a10->fmt.code;
+ ov02a10_fill_fmt(ov02a10->cur_mode, mbus_fmt);
+
+ mutex_unlock(&ov02a10->mutex);
+
+ return 0;
+}
+
+static int ov02a10_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ struct ov02a10 *ov02a10 = to_ov02a10(sd);
+
+ if (code->index >= ARRAY_SIZE(supported_modes))
+ return -EINVAL;
+
+ code->code = ov02a10->fmt.code;
+
+ return 0;
+}
+
+static int ov02a10_enum_frame_sizes(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_frame_size_enum *fse)
+{
+ if (fse->index >= ARRAY_SIZE(supported_modes))
+ return -EINVAL;
+
+ fse->min_width = supported_modes[fse->index].width;
+ fse->max_width = supported_modes[fse->index].width;
+ fse->max_height = supported_modes[fse->index].height;
+ fse->min_height = supported_modes[fse->index].height;
+
+ return 0;
+}
+
+static int __ov02a10_power_on(struct ov02a10 *ov02a10)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+ struct device *dev = &client->dev;
+ int ret;
+
+ gpiod_set_value_cansleep(ov02a10->n_rst_gpio, GPIOD_OUT_LOW);
+ gpiod_set_value_cansleep(ov02a10->pd_gpio, GPIOD_OUT_HIGH);
+
+ ret = clk_prepare_enable(ov02a10->eclk);
+ if (ret < 0) {
+ dev_err(dev, "failed to enable eclk\n");
+ return ret;
+ }
+
+ ret = regulator_bulk_enable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
+ if (ret < 0) {
+ dev_err(dev, "failed to enable regulators\n");
+ goto disable_clk;
+ }
+ usleep_range(5000, 6000);
+
+ gpiod_set_value_cansleep(ov02a10->pd_gpio, GPIOD_OUT_LOW);
+ usleep_range(5000, 6000);
+
+ gpiod_set_value_cansleep(ov02a10->n_rst_gpio, GPIOD_OUT_HIGH);
+ usleep_range(5000, 6000);
+
+ return 0;
+
+disable_clk:
+ clk_disable_unprepare(ov02a10->eclk);
+
+ return ret;
+}
+
+static void __ov02a10_power_off(struct ov02a10 *ov02a10)
+{
+ gpiod_set_value_cansleep(ov02a10->n_rst_gpio, 1);
+ clk_disable_unprepare(ov02a10->eclk);
+ gpiod_set_value_cansleep(ov02a10->pd_gpio, 1);
+ regulator_bulk_disable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
+}
+
+static int __ov02a10_start_stream(struct ov02a10 *ov02a10)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+ const struct ov02a10_reg_list *reg_list;
+ int ret;
+
+ /* Apply default values of current mode */
+ reg_list = &ov02a10->cur_mode->reg_list;
+ ret = ov02a10_write_array(ov02a10, reg_list);
+ if (ret)
+ return ret;
+
+ /* Apply customized values from user */
+ ret = __v4l2_ctrl_handler_setup(ov02a10->subdev.ctrl_handler);
+ if (ret)
+ return ret;
+
+ /* Set orientation to 180 degree */
+ if (ov02a10->upside_down) {
+ ret = i2c_smbus_write_byte_data(client, REG_MIRROR_FLIP_CONTROL,
+ REG_MIRROR_FLIP_ENABLE);
+ if (ret) {
+ dev_err(&client->dev, "failed to set orientation\n");
+ return ret;
+ }
+ ret = i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
+ REG_ENABLE);
+ if (ret < 0)
+ return ret;
+ }
+
+ /* Set stream on register */
+ return i2c_smbus_write_byte_data(client,
+ REG_SC_CTRL_MODE, SC_CTRL_MODE_STREAMING);
+}
+
+static int __ov02a10_stop_stream(struct ov02a10 *ov02a10)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+
+ return i2c_smbus_write_byte_data(client,
+ REG_SC_CTRL_MODE, SC_CTRL_MODE_STANDBY);
+}
+
+static int ov02a10_entity_init_cfg(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg)
+{
+ struct ov02a10 *ov02a10 = to_ov02a10(sd);
+ struct v4l2_subdev_format fmt = { 0 };
+
+ fmt.which = cfg ? V4L2_SUBDEV_FORMAT_TRY : V4L2_SUBDEV_FORMAT_ACTIVE;
+ fmt.format.width = ov02a10->cur_mode->width;
+ fmt.format.height = ov02a10->cur_mode->width;
+
+ ov02a10_set_fmt(sd, cfg, &fmt);
+
+ return 0;
+}
+
+static int ov02a10_s_stream(struct v4l2_subdev *sd, int on)
+{
+ struct ov02a10 *ov02a10 = to_ov02a10(sd);
+ struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+ int ret = 0;
+
+ dev_dbg(&client->dev, "ov02a10 s_stream (%d)\n", on);
+ mutex_lock(&ov02a10->mutex);
+
+ if (ov02a10->streaming == on)
+ goto unlock_and_return;
+
+ if (on) {
+ ret = pm_runtime_get_sync(&client->dev);
+ if (ret < 0) {
+ pm_runtime_put_noidle(&client->dev);
+ goto unlock_and_return;
+ }
+
+ ret = __ov02a10_start_stream(ov02a10);
+ if (ret) {
+ __ov02a10_stop_stream(ov02a10);
+ ov02a10->streaming = !on;
+ goto err_rpm_put;
+ }
+ } else {
+ __ov02a10_stop_stream(ov02a10);
+ pm_runtime_put(&client->dev);
+ }
+
+ ov02a10->streaming = on;
+ mutex_unlock(&ov02a10->mutex);
+
+ return ret;
+
+err_rpm_put:
+ pm_runtime_put(&client->dev);
+unlock_and_return:
+ mutex_unlock(&ov02a10->mutex);
+
+ return ret;
+}
+
+static int __maybe_unused ov02a10_runtime_resume(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct ov02a10 *ov02a10 = to_ov02a10(sd);
+
+ return __ov02a10_power_on(ov02a10);
+}
+
+static int __maybe_unused ov02a10_runtime_suspend(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct ov02a10 *ov02a10 = to_ov02a10(sd);
+
+ __ov02a10_power_off(ov02a10);
+
+ return 0;
+}
+
+static const struct dev_pm_ops ov02a10_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+ pm_runtime_force_resume)
+ SET_RUNTIME_PM_OPS(ov02a10_runtime_suspend,
+ ov02a10_runtime_resume, NULL)
+};
+
+/*
+ * ov02a10_set_exposure - Function called when setting exposure time
+ * @priv: Pointer to device structure
+ * @val: Variable for exposure time, in the unit of micro-second
+ *
+ * Set exposure time based on input value.
+ *
+ * Return: 0 on success
+ */
+static int ov02a10_set_exposure(struct ov02a10 *ov02a10, int val)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+ int ret;
+
+ ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
+ if (ret < 0)
+ return ret;
+
+ ret = i2c_smbus_write_byte_data(client, OV02A10_REG_EXPOSURE_H,
+ ((val >> OV02A10_EXP_SHIFT) &
+ OV02A10_MASK_8_BITS));
+ if (ret < 0)
+ return ret;
+
+ ret = i2c_smbus_write_byte_data(client, OV02A10_REG_EXPOSURE_L,
+ (val & OV02A10_MASK_8_BITS));
+ if (ret < 0)
+ return ret;
+
+ return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
+ REG_ENABLE);
+}
+
+static int ov02a10_set_gain(struct ov02a10 *ov02a10, int val)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+ int ret;
+
+ ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
+ if (ret < 0)
+ return ret;
+
+ ret = i2c_smbus_write_byte_data(client, OV02A10_REG_GAIN,
+ (val & OV02A10_MASK_8_BITS));
+ if (ret < 0)
+ return ret;
+
+ return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
+ REG_ENABLE);
+}
+
+static int ov02a10_set_vblank(struct ov02a10 *ov02a10, int val)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+ int ret;
+
+ ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
+ if (ret < 0)
+ return ret;
+
+ ret = i2c_smbus_write_byte_data(client, OV02A10_REG_VTS_H,
+ (((val + ov02a10->cur_mode->height -
+ OV02A10_BASIC_LINE) >>
+ OV02A10_VTS_SHIFT) &
+ OV02A10_MASK_8_BITS));
+ if (ret < 0)
+ return ret;
+
+ ret = i2c_smbus_write_byte_data(client, OV02A10_REG_VTS_L,
+ ((val + ov02a10->cur_mode->height -
+ OV02A10_BASIC_LINE) &
+ OV02A10_MASK_8_BITS));
+ if (ret < 0)
+ return ret;
+
+ return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
+ REG_ENABLE);
+}
+
+static int ov02a10_set_test_pattern(struct ov02a10 *ov02a10, int pattern)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+ int ret;
+
+ if (pattern)
+ pattern = OV02A10_TEST_PATTERN_ENABLE;
+
+ ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
+ if (ret < 0)
+ return ret;
+
+ ret = i2c_smbus_write_byte_data(client, OV02A10_REG_TEST_PATTERN,
+ pattern);
+ if (ret < 0)
+ return ret;
+
+ ret = i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
+ REG_ENABLE);
+ if (ret < 0)
+ return ret;
+
+ return i2c_smbus_write_byte_data(client, REG_SC_CTRL_MODE,
+ SC_CTRL_MODE_STREAMING);
+}
+
+static int ov02a10_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+ struct ov02a10 *ov02a10 = container_of(ctrl->handler,
+ struct ov02a10, ctrl_handler);
+ struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+ s64 max_expo;
+ int ret;
+
+ /* Propagate change of current control to all related controls */
+ if (ctrl->id == V4L2_CID_VBLANK) {
+ /* Update max exposure while meeting expected vblanking */
+ max_expo = ov02a10->cur_mode->height + ctrl->val -
+ OV02A10_EXPOSURE_MAX_MARGIN;
+ __v4l2_ctrl_modify_range(ov02a10->exposure,
+ ov02a10->exposure->minimum, max_expo,
+ ov02a10->exposure->step,
+ ov02a10->exposure->default_value);
+ }
+
+ /* V4L2 controls values will be applied only when power is already up */
+ if (!pm_runtime_get_if_in_use(&client->dev))
+ return 0;
+
+ switch (ctrl->id) {
+ case V4L2_CID_EXPOSURE:
+ ret = ov02a10_set_exposure(ov02a10, ctrl->val);
+ break;
+ case V4L2_CID_ANALOGUE_GAIN:
+ ret = ov02a10_set_gain(ov02a10, ctrl->val);
+ break;
+ case V4L2_CID_VBLANK:
+ ret = ov02a10_set_vblank(ov02a10, ctrl->val);
+ break;
+ case V4L2_CID_TEST_PATTERN:
+ ret = ov02a10_set_test_pattern(ov02a10, ctrl->val);
+ break;
+ };
+
+ pm_runtime_put(&client->dev);
+
+ return ret;
+}
+
+static const struct v4l2_subdev_video_ops ov02a10_video_ops = {
+ .s_stream = ov02a10_s_stream,
+};
+
+static const struct v4l2_subdev_pad_ops ov02a10_pad_ops = {
+ .init_cfg = ov02a10_entity_init_cfg,
+ .enum_mbus_code = ov02a10_enum_mbus_code,
+ .enum_frame_size = ov02a10_enum_frame_sizes,
+ .get_fmt = ov02a10_get_fmt,
+ .set_fmt = ov02a10_set_fmt,
+};
+
+static const struct v4l2_subdev_ops ov02a10_subdev_ops = {
+ .video = &ov02a10_video_ops,
+ .pad = &ov02a10_pad_ops,
+};
+
+static const struct media_entity_operations ov02a10_subdev_entity_ops = {
+ .link_validate = v4l2_subdev_link_validate,
+};
+
+static const struct v4l2_ctrl_ops ov02a10_ctrl_ops = {
+ .s_ctrl = ov02a10_set_ctrl,
+};
+
+static int ov02a10_initialize_controls(struct ov02a10 *ov02a10)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+ const struct ov02a10_mode *mode;
+ struct v4l2_ctrl_handler *handler;
+ struct v4l2_ctrl *ctrl;
+ u64 exposure_max;
+ u32 pixel_rate, h_blank;
+ int ret;
+
+ handler = &ov02a10->ctrl_handler;
+ mode = ov02a10->cur_mode;
+ ret = v4l2_ctrl_handler_init(handler, 7);
+ if (ret)
+ return ret;
+
+ handler->lock = &ov02a10->mutex;
+
+ ctrl = v4l2_ctrl_new_int_menu(handler, NULL, V4L2_CID_LINK_FREQ,
+ 0, 0, link_freq_menu_items);
+ if (ctrl)
+ ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+ pixel_rate = to_pixel_rate(0);
+ v4l2_ctrl_new_std(handler, NULL, V4L2_CID_PIXEL_RATE,
+ 0, pixel_rate, 1, pixel_rate);
+
+ h_blank = mode->hts_def - mode->width;
+ ov02a10->hblank = v4l2_ctrl_new_std(handler, NULL, V4L2_CID_HBLANK,
+ h_blank, h_blank, 1, h_blank);
+ if (ov02a10->hblank)
+ ov02a10->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+ ov02a10->vblank = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
+ V4L2_CID_VBLANK, mode->vts_def -
+ mode->height,
+ OV02A10_VTS_MAX - mode->height, 1,
+ mode->vts_def - mode->height);
+
+ exposure_max = mode->vts_def - 4;
+ ov02a10->exposure = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
+ V4L2_CID_EXPOSURE,
+ OV02A10_EXPOSURE_MIN,
+ exposure_max,
+ OV02A10_EXPOSURE_STEP,
+ mode->exp_def);
+
+ ov02a10->anal_gain = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
+ V4L2_CID_ANALOGUE_GAIN,
+ OV02A10_GAIN_MIN,
+ OV02A10_GAIN_MAX,
+ OV02A10_GAIN_STEP,
+ OV02A10_GAIN_DEFAULT);
+
+ ov02a10->test_pattern =
+ v4l2_ctrl_new_std_menu_items(handler,
+ &ov02a10_ctrl_ops,
+ V4L2_CID_TEST_PATTERN,
+ ARRAY_SIZE(ov02a10_test_pattern_menu) -
+ 1, 0, 0,
+ ov02a10_test_pattern_menu);
+
+ if (handler->error) {
+ ret = handler->error;
+ dev_err(&client->dev, "failed to init controls(%d)\n", ret);
+ goto err_free_handler;
+ }
+
+ ov02a10->subdev.ctrl_handler = handler;
+
+ return 0;
+
+err_free_handler:
+ v4l2_ctrl_handler_free(handler);
+
+ return ret;
+}
+
+static int ov02a10_check_hwcfg(struct device *dev)
+{
+ struct fwnode_handle *ep;
+ struct fwnode_handle *fwnode = dev_fwnode(dev);
+ struct v4l2_fwnode_endpoint bus_cfg = {
+ .bus_type = V4L2_MBUS_CSI2_DPHY
+ };
+ unsigned int i, j;
+ int ret;
+
+ if (!fwnode)
+ return -ENXIO;
+
+ ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
+ if (!ep)
+ return -ENXIO;
+
+ ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg);
+ fwnode_handle_put(ep);
+ if (ret)
+ return ret;
+
+ if (!bus_cfg.nr_of_link_frequencies) {
+ dev_err(dev, "no link frequencies defined");
+ ret = -EINVAL;
+ goto check_hwcfg_error;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(link_freq_menu_items); i++) {
+ for (j = 0; j < bus_cfg.nr_of_link_frequencies; j++) {
+ if (link_freq_menu_items[i] ==
+ bus_cfg.link_frequencies[j])
+ break;
+ }
+
+ if (j == bus_cfg.nr_of_link_frequencies) {
+ dev_err(dev, "no link frequency %lld supported",
+ link_freq_menu_items[i]);
+ ret = -EINVAL;
+ goto check_hwcfg_error;
+ }
+ }
+
+check_hwcfg_error:
+ v4l2_fwnode_endpoint_free(&bus_cfg);
+
+ return ret;
+}
+
+static int ov02a10_check_sensor_id(struct ov02a10 *ov02a10)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
+ u16 id;
+ u8 pid = 0;
+ u8 ver = 0;
+ int ret;
+
+ /* Check sensor revision */
+ ret = ov02a10_read_smbus(ov02a10, OV02A10_REG_CHIP_ID_H, &pid);
+ if (ret)
+ return ret;
+
+ ret = ov02a10_read_smbus(ov02a10, OV02A10_REG_CHIP_ID_L, &ver);
+ if (ret)
+ return ret;
+
+ id = OV02A10_ID(pid, ver);
+ if (id != CHIP_ID) {
+ dev_err(&client->dev, "Unexpected sensor id(%04x)\n", id);
+ return ret;
+ }
+
+ dev_info(&client->dev, "Detected OV%04X sensor\n", id);
+
+ return 0;
+}
+
+static int ov02a10_probe(struct i2c_client *client)
+{
+ struct device *dev = &client->dev;
+ struct ov02a10 *ov02a10;
+ unsigned int rotation;
+ unsigned int i;
+ int ret;
+
+ dev_info(dev, "ov02a10 probe aaaa++\n");
+
+ ret = ov02a10_check_hwcfg(dev);
+ if (ret) {
+ dev_err(dev, "failed to check HW configuration: %d",
+ ret);
+ return ret;
+ }
+
+ ov02a10 = devm_kzalloc(dev, sizeof(*ov02a10), GFP_KERNEL);
+ if (!ov02a10)
+ return -ENOMEM;
+
+ v4l2_i2c_subdev_init(&ov02a10->subdev, client, &ov02a10_subdev_ops);
+ ov02a10->fmt.code = MEDIA_BUS_FMT_SBGGR10_1X10;
+
+ /* Optional indication of physical rotation of sensor */
+ ret = fwnode_property_read_u32(dev_fwnode(dev), "rotation",
+ &rotation);
+ if (!ret) {
+ switch (rotation) {
+ case 180:
+ ov02a10->upside_down = true;
+ ov02a10->fmt.code = MEDIA_BUS_FMT_SRGGB10_1X10;
+ break;
+ case 0:
+ break;
+ default:
+ dev_warn(dev, "%u degrees rotation is not supported, ignoring...\n",
+ rotation);
+ }
+ }
+
+ /* Get system clock (eclk) */
+ ov02a10->eclk = devm_clk_get(dev, "eclk");
+ if (IS_ERR(ov02a10->eclk)) {
+ dev_err(dev, "failed to get eclk\n");
+ return -EINVAL;
+ }
+
+ ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
+ &ov02a10->eclk_freq);
+ if (ret) {
+ dev_err(dev, "failed to get eclk frequency\n");
+ return ret;
+ }
+
+ ret = clk_set_rate(ov02a10->eclk, ov02a10->eclk_freq);
+ if (ret) {
+ dev_err(dev, "failed to set eclk frequency (24MHz)\n");
+ return ret;
+ }
+
+ if (clk_get_rate(ov02a10->eclk) != OV02A10_ECLK_FREQ) {
+ dev_warn(dev, "wrong eclk frequency %d Hz, expected: %d Hz\n",
+ ov02a10->eclk_freq, OV02A10_ECLK_FREQ);
+ return -EINVAL;
+ }
+
+ ov02a10->pd_gpio = devm_gpiod_get(dev, "powerdown", GPIOD_OUT_HIGH);
+ if (IS_ERR(ov02a10->pd_gpio)) {
+ dev_err(dev, "failed to get powerdown-gpios\n");
+ return -EINVAL;
+ }
+
+ ov02a10->n_rst_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(ov02a10->n_rst_gpio)) {
+ dev_err(dev, "failed to get reset-gpios\n");
+ return -EINVAL;
+ }
+
+ for (i = 0; i < OV02A10_NUM_SUPPLIES; i++)
+ ov02a10->supplies[i].supply = ov02a10_supply_names[i];
+
+ ret = devm_regulator_bulk_get(dev,
+ OV02A10_NUM_SUPPLIES,
+ ov02a10->supplies);
+ if (ret) {
+ dev_err(dev, "failed to get regulators\n");
+ return ret;
+ }
+
+ mutex_init(&ov02a10->mutex);
+ ov02a10->cur_mode = &supported_modes[0];
+ ret = ov02a10_initialize_controls(ov02a10);
+ if (ret) {
+ dev_err(dev, "failed to initialize controls\n");
+ goto err_destroy_mutex;
+ }
+
+ ret = __ov02a10_power_on(ov02a10);
+ if (ret)
+ goto err_free_handler;
+
+ ret = ov02a10_check_sensor_id(ov02a10);
+ if (ret)
+ goto err_power_off;
+
+ ov02a10->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+ ov02a10->subdev.entity.ops = &ov02a10_subdev_entity_ops;
+ ov02a10->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+ ov02a10->pad.flags = MEDIA_PAD_FL_SOURCE;
+ ret = media_entity_pads_init(&ov02a10->subdev.entity, 1, &ov02a10->pad);
+ if (ret < 0) {
+ dev_err(dev, "failed to init entity pads: %d", ret);
+ goto err_power_off;
+ }
+
+ ret = v4l2_async_register_subdev(&ov02a10->subdev);
+ if (ret) {
+ dev_err(dev, "failed to register V4L2 subdev: %d",
+ ret);
+ goto err_clean_entity;
+ }
+
+ pm_runtime_set_active(dev);
+ pm_runtime_enable(dev);
+ pm_runtime_idle(dev);
+
+ dev_info(dev, "ov02a10 probe --\n");
+ return 0;
+
+err_clean_entity:
+ media_entity_cleanup(&ov02a10->subdev.entity);
+err_power_off:
+ __ov02a10_power_off(ov02a10);
+err_free_handler:
+ v4l2_ctrl_handler_free(ov02a10->subdev.ctrl_handler);
+err_destroy_mutex:
+ mutex_destroy(&ov02a10->mutex);
+
+ return ret;
+}
+
+static int ov02a10_remove(struct i2c_client *client)
+{
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct ov02a10 *ov02a10 = to_ov02a10(sd);
+
+ v4l2_async_unregister_subdev(sd);
+ media_entity_cleanup(&sd->entity);
+ v4l2_ctrl_handler_free(sd->ctrl_handler);
+ pm_runtime_disable(&client->dev);
+ if (!pm_runtime_status_suspended(&client->dev))
+ __ov02a10_power_off(ov02a10);
+ pm_runtime_set_suspended(&client->dev);
+ mutex_destroy(&ov02a10->mutex);
+
+ return 0;
+}
+
+static const struct of_device_id ov02a10_of_match[] = {
+ { .compatible = "ovti,ov02a10" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, ov02a10_of_match);
+
+static struct i2c_driver ov02a10_i2c_driver = {
+ .driver = {
+ .name = "ov02a10",
+ .pm = &ov02a10_pm_ops,
+ .of_match_table = ov02a10_of_match,
+ },
+ .probe_new = &ov02a10_probe,
+ .remove = &ov02a10_remove,
+};
+
+module_i2c_driver(ov02a10_i2c_driver);
+
+MODULE_AUTHOR("Dongchun Zhu <dongchun.zhu@mediatek.com>");
+MODULE_DESCRIPTION("OmniVision OV02A10 sensor driver");
+MODULE_LICENSE("GPL v2");
+
--
2.9.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [V4, 2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver
2019-09-07 9:27 ` [V4, 2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver dongchun.zhu
@ 2019-09-08 2:00 ` kbuild test robot
2019-09-08 2:31 ` kbuild test robot
` (2 subsequent siblings)
3 siblings, 0 replies; 12+ messages in thread
From: kbuild test robot @ 2019-09-08 2:00 UTC (permalink / raw)
To: dongchun.zhu
Cc: mark.rutland, drinkcat, andriy.shevchenko, srv_heupstream,
devicetree, shengnan.wang, dongchun.zhu, tfiga, louis.kuo,
sj.huang, robh+dt, linux-mediatek, kbuild-all, sakari.ailus,
matthias.bgg, bingbu.cao, mchehab, linux-arm-kernel, linux-media
[-- Attachment #1: Type: text/plain, Size: 2822 bytes --]
Hi,
I love your patch! Perhaps something to improve:
[auto build test WARNING on linuxtv-media/master]
[cannot apply to v5.3-rc7 next-20190904]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/dongchun-zhu-mediatek-com/media-i2c-Add-support-for-OV02A10-sensor/20190908-065643
base: git://linuxtv.org/media_tree.git master
config: x86_64-allyesconfig (attached as .config)
compiler: gcc-7 (Debian 7.4.0-11) 7.4.0
reproduce:
# save the attached .config to linux build tree
make ARCH=x86_64
If you fix the issue, kindly add following tag
Reported-by: kbuild test robot <lkp@intel.com>
Note: it may well be a FALSE warning. FWIW you are at least aware of it now.
http://gcc.gnu.org/wiki/Better_Uninitialized_Warnings
All warnings (new ones prefixed by >>):
drivers/media/i2c/ov02a10.c: In function 'ov02a10_set_ctrl':
>> drivers/media/i2c/ov02a10.c:699:9: warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
return ret;
^~~
vim +/ret +699 drivers/media/i2c/ov02a10.c
658
659 static int ov02a10_set_ctrl(struct v4l2_ctrl *ctrl)
660 {
661 struct ov02a10 *ov02a10 = container_of(ctrl->handler,
662 struct ov02a10, ctrl_handler);
663 struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
664 s64 max_expo;
665 int ret;
666
667 /* Propagate change of current control to all related controls */
668 if (ctrl->id == V4L2_CID_VBLANK) {
669 /* Update max exposure while meeting expected vblanking */
670 max_expo = ov02a10->cur_mode->height + ctrl->val -
671 OV02A10_EXPOSURE_MAX_MARGIN;
672 __v4l2_ctrl_modify_range(ov02a10->exposure,
673 ov02a10->exposure->minimum, max_expo,
674 ov02a10->exposure->step,
675 ov02a10->exposure->default_value);
676 }
677
678 /* V4L2 controls values will be applied only when power is already up */
679 if (!pm_runtime_get_if_in_use(&client->dev))
680 return 0;
681
682 switch (ctrl->id) {
683 case V4L2_CID_EXPOSURE:
684 ret = ov02a10_set_exposure(ov02a10, ctrl->val);
685 break;
686 case V4L2_CID_ANALOGUE_GAIN:
687 ret = ov02a10_set_gain(ov02a10, ctrl->val);
688 break;
689 case V4L2_CID_VBLANK:
690 ret = ov02a10_set_vblank(ov02a10, ctrl->val);
691 break;
692 case V4L2_CID_TEST_PATTERN:
693 ret = ov02a10_set_test_pattern(ov02a10, ctrl->val);
694 break;
695 };
696
697 pm_runtime_put(&client->dev);
698
> 699 return ret;
700 }
701
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 69517 bytes --]
[-- Attachment #3: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [V4, 2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver
2019-09-07 9:27 ` [V4, 2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver dongchun.zhu
2019-09-08 2:00 ` kbuild test robot
@ 2019-09-08 2:31 ` kbuild test robot
2019-09-08 2:31 ` [PATCH] media: i2c: fix semicolon.cocci warnings kbuild test robot
2019-09-09 6:55 ` [V4, 2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver Sakari Ailus
3 siblings, 0 replies; 12+ messages in thread
From: kbuild test robot @ 2019-09-08 2:31 UTC (permalink / raw)
To: dongchun.zhu
Cc: mark.rutland, drinkcat, andriy.shevchenko, srv_heupstream,
devicetree, shengnan.wang, dongchun.zhu, tfiga, louis.kuo,
sj.huang, robh+dt, linux-mediatek, kbuild-all, sakari.ailus,
matthias.bgg, bingbu.cao, mchehab, linux-arm-kernel, linux-media
Hi,
I love your patch! Perhaps something to improve:
[auto build test WARNING on linuxtv-media/master]
[cannot apply to v5.3-rc7 next-20190904]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/dongchun-zhu-mediatek-com/media-i2c-Add-support-for-OV02A10-sensor/20190908-065643
base: git://linuxtv.org/media_tree.git master
If you fix the issue, kindly add following tag
Reported-by: kbuild test robot <lkp@intel.com>
coccinelle warnings: (new ones prefixed by >>)
>> drivers/media/i2c/ov02a10.c:695:2-3: Unneeded semicolon
Please review and possibly fold the followup patch.
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH] media: i2c: fix semicolon.cocci warnings
2019-09-07 9:27 ` [V4, 2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver dongchun.zhu
2019-09-08 2:00 ` kbuild test robot
2019-09-08 2:31 ` kbuild test robot
@ 2019-09-08 2:31 ` kbuild test robot
2019-09-09 6:55 ` [V4, 2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver Sakari Ailus
3 siblings, 0 replies; 12+ messages in thread
From: kbuild test robot @ 2019-09-08 2:31 UTC (permalink / raw)
To: dongchun.zhu
Cc: mark.rutland, drinkcat, andriy.shevchenko, srv_heupstream,
devicetree, shengnan.wang, dongchun.zhu, tfiga, louis.kuo,
sj.huang, robh+dt, linux-mediatek, kbuild-all, sakari.ailus,
matthias.bgg, bingbu.cao, mchehab, linux-arm-kernel, linux-media
From: kbuild test robot <lkp@intel.com>
drivers/media/i2c/ov02a10.c:695:2-3: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
Fixes: 2bca4b808db1 ("media: i2c: Add Omnivision OV02A10 camera sensor driver")
CC: Dongchun Zhu <dongchun.zhu@mediatek.com>
Signed-off-by: kbuild test robot <lkp@intel.com>
---
url: https://github.com/0day-ci/linux/commits/dongchun-zhu-mediatek-com/media-i2c-Add-support-for-OV02A10-sensor/20190908-065643
base: git://linuxtv.org/media_tree.git master
ov02a10.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/media/i2c/ov02a10.c
+++ b/drivers/media/i2c/ov02a10.c
@@ -692,7 +692,7 @@ static int ov02a10_set_ctrl(struct v4l2_
case V4L2_CID_TEST_PATTERN:
ret = ov02a10_set_test_pattern(ov02a10, ctrl->val);
break;
- };
+ }
pm_runtime_put(&client->dev);
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [V4, 1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10
2019-09-07 9:27 ` [V4, 1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10 dongchun.zhu
@ 2019-09-09 6:46 ` Sakari Ailus
2019-09-09 9:45 ` Andy Shevchenko
1 sibling, 0 replies; 12+ messages in thread
From: Sakari Ailus @ 2019-09-09 6:46 UTC (permalink / raw)
To: dongchun.zhu
Cc: mark.rutland, drinkcat, andriy.shevchenko, srv_heupstream,
devicetree, shengnan.wang, tfiga, louis.kuo, sj.huang, robh+dt,
linux-mediatek, matthias.bgg, bingbu.cao, mchehab,
linux-arm-kernel, linux-media
Hi Dongchun,
On Sat, Sep 07, 2019 at 05:27:27PM +0800, dongchun.zhu@mediatek.com wrote:
> From: Dongchun Zhu <dongchun.zhu@mediatek.com>
>
> This patch adds device tree bindings documentation for OV02A10 camera sensor.
>
> Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Please remember to add acks you get.
> ---
> .../devicetree/bindings/media/i2c/ov02a10.txt | 54 ++++++++++++++++++++++
> MAINTAINERS | 7 +++
> 2 files changed, 61 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/i2c/ov02a10.txt
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/ov02a10.txt b/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> new file mode 100644
> index 0000000..18acc4f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> @@ -0,0 +1,54 @@
> +* Omnivision OV02A10 MIPI CSI-2 sensor
> +
> +Required Properties:
> +- compatible: shall be "ovti,ov02a10"
> +- clocks: reference to the eclk input clock
> +- clock-names: shall be "eclk"
> +- dovdd-supply: Digital I/O voltage supply, 1.8 volts
> +- avdd-supply: Analog voltage supply, 2.8 volts
> +- dvdd-supply: Digital core voltage supply, 1.8 volts
> +- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
> + if any. This is an active low signal to the OV02A10.
> +- reset-gpios: reference to the GPIO connected to the reset pin, if any.
> + This is an active high signal to the OV02A10.
> +
> +Optional Properties:
> +- rotation: as defined in
> + Documentation/devicetree/bindings/media/video-interfaces.txt,
> + valid values are 0 (sensor mounted upright) and 180 (sensor
> + mounted upside down).
This needs to be either mandatory or the default needs to be documented. I
think it could be simply:
Documentation/devicetree/bindings/media/video-interfaces.txt,
valid values are 0 (sensor mounted upright; the default) and
180 (sensor mounted upside down).
> +
> +The device node shall contain one 'port' child node with an
> +'endpoint' subnode for its digital output video port,
> +in accordance with the video interface bindings defined in
> +Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> +Example:
> +&i2c4 {
> + ov02a10: camera-sensor@3d {
> + compatible = "ovti,ov02a10";
> + reg = <0x3d>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&camera_pins_cam1_mclk_on>;
> +
> + clocks = <&topckgen CLK_TOP_MUX_CAMTG2>,
> + <&topckgen CLK_TOP_UNIVP_192M_D8>;
> + clock-names = "eclk", "freq_mux";
> + clock-frequency = <24000000>;
> +
> + dovdd-supply = <&mt6358_vcamio_reg>;
> + avdd-supply = <&mt6358_vcama1_reg>;
> + dvdd-supply = <&mt6358_vcn18_reg>;
> + powerdown-gpios = <&pio 107 GPIO_ACTIVE_LOW>;
> + reset-gpios = <&pio 109 GPIO_ACTIVE_HIGH>;
> + rotation = <180>;
> +
> + port {
> + /* MIPI CSI-2 bus endpoint */
> + ov02a10_core: endpoint {
> + remote-endpoint = <&ov02a10_0>;
> + link-frequencies = /bits/ 64 <390000000>;
> + };
> + };
> + };
> +};
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 783569e..41734fb 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -11816,6 +11816,13 @@ T: git git://linuxtv.org/media_tree.git
> S: Maintained
> F: drivers/media/i2c/ov13858.c
>
> +OMNIVISION OV02A10 SENSOR DRIVER
> +M: Dongchun Zhu <dongchun.zhu@mediatek.com>
> +L: linux-media@vger.kernel.org
> +T: git git://linuxtv.org/media_tree.git
> +S: Maintained
> +F: Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> +
> OMNIVISION OV2680 SENSOR DRIVER
> M: Rui Miguel Silva <rmfrfs@gmail.com>
> L: linux-media@vger.kernel.org
--
Regards,
Sakari Ailus
sakari.ailus@linux.intel.com
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [V4, 2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver
2019-09-07 9:27 ` [V4, 2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver dongchun.zhu
` (2 preceding siblings ...)
2019-09-08 2:31 ` [PATCH] media: i2c: fix semicolon.cocci warnings kbuild test robot
@ 2019-09-09 6:55 ` Sakari Ailus
2019-11-04 3:30 ` Dongchun Zhu
3 siblings, 1 reply; 12+ messages in thread
From: Sakari Ailus @ 2019-09-09 6:55 UTC (permalink / raw)
To: dongchun.zhu
Cc: mark.rutland, drinkcat, andriy.shevchenko, srv_heupstream,
devicetree, shengnan.wang, tfiga, louis.kuo, sj.huang, robh+dt,
linux-mediatek, matthias.bgg, bingbu.cao, mchehab,
linux-arm-kernel, linux-media
Hi Dongchun,
Thanks for the update. A few more comments below.
On Sat, Sep 07, 2019 at 05:27:28PM +0800, dongchun.zhu@mediatek.com wrote:
> From: Dongchun Zhu <dongchun.zhu@mediatek.com>
>
> This patch adds a V4L2 sub-device driver for OV02A10 image sensor.
> The OV02A10 is a 1/5" CMOS sensor from Omnivision,
> supporting output format: 10-bit Raw.
>
> The OV02A10 has a single MIPI lane interface and use the I2C bus
> for control and the CSI-2 bus for data.
>
> Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
> ---
> MAINTAINERS | 1 +
> drivers/media/i2c/Kconfig | 11 +
> drivers/media/i2c/Makefile | 1 +
> drivers/media/i2c/ov02a10.c | 1062 +++++++++++++++++++++++++++++++++++++++++++
> 4 files changed, 1075 insertions(+)
> create mode 100644 drivers/media/i2c/ov02a10.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 41734fb..4b714a2 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -11821,6 +11821,7 @@ M: Dongchun Zhu <dongchun.zhu@mediatek.com>
> L: linux-media@vger.kernel.org
> T: git git://linuxtv.org/media_tree.git
> S: Maintained
> +F: drivers/media/i2c/ov02a10.c
> F: Documentation/devicetree/bindings/media/i2c/ov02a10.txt
>
> OMNIVISION OV2680 SENSOR DRIVER
> diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> index 79ce9ec..22e0db4 100644
> --- a/drivers/media/i2c/Kconfig
> +++ b/drivers/media/i2c/Kconfig
> @@ -617,6 +617,17 @@ config VIDEO_IMX355
> To compile this driver as a module, choose M here: the
> module will be called imx355.
>
> +config VIDEO_OV02A10
> + tristate "OmniVision OV02A10 sensor support"
> + depends on VIDEO_V4L2 && I2C
> + depends on MEDIA_CAMERA_SUPPORT
Please add VIDEO_V4L2_SUBDEV_API
> + help
> + This is a Video4Linux2 sensor driver for the OmniVision
> + OV02A10 camera.
> +
> + To compile this driver as a module, choose M here: the
> + module will be called ov02a10.
> +
> config VIDEO_OV2640
> tristate "OmniVision OV2640 sensor support"
> depends on VIDEO_V4L2 && I2C
> diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> index fd4ea86..d27f4e2 100644
> --- a/drivers/media/i2c/Makefile
> +++ b/drivers/media/i2c/Makefile
> @@ -63,6 +63,7 @@ obj-$(CONFIG_VIDEO_VP27SMPX) += vp27smpx.o
> obj-$(CONFIG_VIDEO_SONY_BTF_MPX) += sony-btf-mpx.o
> obj-$(CONFIG_VIDEO_UPD64031A) += upd64031a.o
> obj-$(CONFIG_VIDEO_UPD64083) += upd64083.o
> +obj-$(CONFIG_VIDEO_OV02A10) += ov02a10.o
> obj-$(CONFIG_VIDEO_OV2640) += ov2640.o
> obj-$(CONFIG_VIDEO_OV2680) += ov2680.o
> obj-$(CONFIG_VIDEO_OV2685) += ov2685.o
> diff --git a/drivers/media/i2c/ov02a10.c b/drivers/media/i2c/ov02a10.c
> new file mode 100644
> index 0000000..fb677d5
> --- /dev/null
> +++ b/drivers/media/i2c/ov02a10.c
> @@ -0,0 +1,1062 @@
> +// SPDX-License-Identifier: GPL-2.0
> +// Copyright (c) 2019 MediaTek Inc.
> +
> +#include <linux/clk.h>
> +#include <linux/device.h>
> +#include <linux/delay.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/regulator/consumer.h>
> +#include <media/media-entity.h>
> +#include <media/v4l2-async.h>
> +#include <media/v4l2-ctrls.h>
> +#include <media/v4l2-subdev.h>
> +#include <media/v4l2-fwnode.h>
> +
> +#define CHIP_ID 0x2509
> +#define OV02A10_REG_CHIP_ID_H 0x02
> +#define OV02A10_REG_CHIP_ID_L 0x03
> +#define OV02A10_ID(_msb, _lsb) ((_msb) << 8 | (_lsb))
> +
> +/* Bit[1] vertical upside down */
> +/* Bit[0] horizontal mirror */
> +#define REG_MIRROR_FLIP_CONTROL 0x3f
> +
> +/* Orientation */
> +#define REG_MIRROR_FLIP_ENABLE 0x03
> +
> +#define REG_PAGE_SWITCH 0xfd
> +#define REG_GLOBAL_EFFECTIVE 0x01
> +#define REG_ENABLE BIT(0)
> +#define OV02A10_MASK_8_BITS 0xff
> +
> +#define REG_SC_CTRL_MODE 0xac
> +#define SC_CTRL_MODE_STANDBY 0x00
> +#define SC_CTRL_MODE_STREAMING 0x01
> +
> +#define OV02A10_EXP_SHIFT 8
> +#define OV02A10_REG_EXPOSURE_H 0x03
> +#define OV02A10_REG_EXPOSURE_L 0x04
> +#define OV02A10_EXPOSURE_MIN 4
> +#define OV02A10_EXPOSURE_MAX_MARGIN 4
> +#define OV02A10_EXPOSURE_STEP 1
> +
> +#define OV02A10_VTS_SHIFT 8
> +#define OV02A10_REG_VTS_H 0x05
> +#define OV02A10_REG_VTS_L 0x06
> +#define OV02A10_VTS_MAX 0x209f
> +#define OV02A10_VTS_MIN 0x04cf
> +#define OV02A10_BASIC_LINE 1224
> +
> +#define OV02A10_REG_GAIN 0x24
> +#define OV02A10_GAIN_MIN 0x10
> +#define OV02A10_GAIN_MAX 0xf8
> +#define OV02A10_GAIN_STEP 0x01
> +#define OV02A10_GAIN_DEFAULT 0x40
> +
> +/* Test pattern control */
> +#define OV02A10_REG_TEST_PATTERN 0xb6
> +#define OV02A10_TEST_PATTERN_ENABLE BIT(0)
> +
> +#define OV02A10_LINK_FREQ_390MHZ 390000000ULL
> +#define OV02A10_ECLK_FREQ 24000000
> +#define OV02A10_DATA_LANES 1
> +#define OV02A10_BITS_PER_SAMPLE 10
> +
> +static const char * const ov02a10_supply_names[] = {
> + "dovdd", /* Digital I/O power */
> + "avdd", /* Analog power */
> + "dvdd", /* Digital core power */
> +};
> +
> +#define OV02A10_NUM_SUPPLIES ARRAY_SIZE(ov02a10_supply_names)
> +
> +struct ov02a10_reg {
> + u8 addr;
> + u8 val;
> +};
> +
> +struct ov02a10_reg_list {
> + u32 num_of_regs;
> + const struct ov02a10_reg *regs;
> +};
> +
> +struct ov02a10_mode {
> + u32 width;
> + u32 height;
> + u32 exp_def;
> + u32 hts_def;
> + u32 vts_def;
> + const struct ov02a10_reg_list reg_list;
> +};
> +
> +struct ov02a10 {
> + struct clk *eclk;
> + u32 eclk_freq;
> +
> + struct gpio_desc *pd_gpio;
> + struct gpio_desc *n_rst_gpio;
> + struct regulator_bulk_data supplies[OV02A10_NUM_SUPPLIES];
> +
> + bool streaming;
> + bool upside_down;
> +
> + /*
> + * Serialize control access, get/set format, get selection
> + * and start streaming.
> + */
> + struct mutex mutex;
> + struct v4l2_subdev subdev;
> + struct media_pad pad;
> + struct v4l2_ctrl *anal_gain;
> + struct v4l2_ctrl *exposure;
> + struct v4l2_ctrl *hblank;
> + struct v4l2_ctrl *vblank;
> + struct v4l2_ctrl *hflip;
> + struct v4l2_ctrl *vflip;
> + struct v4l2_ctrl *test_pattern;
Of the above references to controls, only exposure appears to be actually
used. Please drop the others.
> + struct v4l2_mbus_framefmt fmt;
> + struct v4l2_ctrl_handler ctrl_handler;
> +
> + const struct ov02a10_mode *cur_mode;
> +};
> +
> +static inline struct ov02a10 *to_ov02a10(struct v4l2_subdev *sd)
> +{
> + return container_of(sd, struct ov02a10, subdev);
> +}
> +
> +/*
> + * eclk 24Mhz
> + * pclk 39Mhz
> + * linelength 934(0x3a6)
> + * framelength 1390(0x56E)
> + * grabwindow_width 1600
> + * grabwindow_height 1200
> + * max_framerate 30fps
> + * mipi_datarate per lane 780Mbps
> + */
> +static const struct ov02a10_reg ov02a10_1600x1200_regs[] = {
> + {0xfd, 0x01},
> + {0xac, 0x00},
> + {0xfd, 0x00},
> + {0x2f, 0x29},
> + {0x34, 0x00},
> + {0x35, 0x21},
> + {0x30, 0x15},
> + {0x33, 0x01},
> + {0xfd, 0x01},
> + {0x44, 0x00},
> + {0x2a, 0x4c},
> + {0x2b, 0x1e},
> + {0x2c, 0x60},
> + {0x25, 0x11},
> + {0x03, 0x01},
> + {0x04, 0xae},
> + {0x09, 0x00},
> + {0x0a, 0x02},
> + {0x06, 0xa6},
> + {0x31, 0x00},
> + {0x24, 0x40},
> + {0x01, 0x01},
> + {0xfb, 0x73},
> + {0xfd, 0x01},
> + {0x16, 0x04},
> + {0x1c, 0x09},
> + {0x21, 0x42},
> + {0x12, 0x04},
> + {0x13, 0x10},
> + {0x11, 0x40},
> + {0x33, 0x81},
> + {0xd0, 0x00},
> + {0xd1, 0x01},
> + {0xd2, 0x00},
> + {0x50, 0x10},
> + {0x51, 0x23},
> + {0x52, 0x20},
> + {0x53, 0x10},
> + {0x54, 0x02},
> + {0x55, 0x20},
> + {0x56, 0x02},
> + {0x58, 0x48},
> + {0x5d, 0x15},
> + {0x5e, 0x05},
> + {0x66, 0x66},
> + {0x68, 0x68},
> + {0x6b, 0x00},
> + {0x6c, 0x00},
> + {0x6f, 0x40},
> + {0x70, 0x40},
> + {0x71, 0x0a},
> + {0x72, 0xf0},
> + {0x73, 0x10},
> + {0x75, 0x80},
> + {0x76, 0x10},
> + {0x84, 0x00},
> + {0x85, 0x10},
> + {0x86, 0x10},
> + {0x87, 0x00},
> + {0x8a, 0x22},
> + {0x8b, 0x22},
> + {0x19, 0xf1},
> + {0x29, 0x01},
> + {0xfd, 0x01},
> + {0x9d, 0xd6},
> + {0xa0, 0x29},
> + {0xa1, 0x03},
> + {0xad, 0x62},
> + {0xae, 0x00},
> + {0xaf, 0x85},
> + {0xb1, 0x01},
> + {0x8e, 0x06},
> + {0x8f, 0x40},
> + {0x90, 0x04},
> + {0x91, 0xb0},
> + {0x45, 0x01},
> + {0x46, 0x00},
> + {0x47, 0x6c},
> + {0x48, 0x03},
> + {0x49, 0x8b},
> + {0x4a, 0x00},
> + {0x4b, 0x07},
> + {0x4c, 0x04},
> + {0x4d, 0xb7},
> + {0xf0, 0x40},
> + {0xf1, 0x40},
> + {0xf2, 0x40},
> + {0xf3, 0x40},
> + {0x3f, 0x00},
> + {0xfd, 0x01},
> + {0x05, 0x00},
> + {0x06, 0xa6},
> + {0xfd, 0x01},
> +};
> +
> +static const char * const ov02a10_test_pattern_menu[] = {
> + "Disabled",
> + "Color Bar",
> +};
> +
> +static const s64 link_freq_menu_items[] = {
> + OV02A10_LINK_FREQ_390MHZ
> +};
> +
> +static u64 to_pixel_rate(u32 f_index)
> +{
> + u64 pixel_rate = link_freq_menu_items[f_index] * 2 * OV02A10_DATA_LANES;
> +
> + do_div(pixel_rate, OV02A10_BITS_PER_SAMPLE);
> +
> + return pixel_rate;
> +}
> +
> +static const struct ov02a10_mode supported_modes[] = {
> + {
> + .width = 1600,
> + .height = 1200,
> + .exp_def = 0x01ae,
> + .hts_def = 0x03a6,
> + .vts_def = 0x056e,
> + .reg_list = {
> + .num_of_regs = ARRAY_SIZE(ov02a10_1600x1200_regs),
> + .regs = ov02a10_1600x1200_regs,
> + },
> + },
> +};
> +
> +static int ov02a10_write_array(struct ov02a10 *ov02a10,
> + const struct ov02a10_reg_list *r_list)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> + unsigned int i;
> + int ret;
> +
> + for (i = 0; i < r_list->num_of_regs; i++) {
> + ret = i2c_smbus_write_byte_data(client,
> + r_list->regs[i].addr,
> + r_list->regs[i].val);
> + if (ret < 0)
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int ov02a10_read_smbus(struct ov02a10 *ov02a10, unsigned char reg,
> + unsigned char *val)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> + int ret;
> +
> + ret = i2c_smbus_read_byte_data(client, reg);
> + if (ret >= 0) {
> + *val = (unsigned char)ret;
> + ret = 0;
> + }
> +
> + return ret;
> +}
> +
> +static void ov02a10_fill_fmt(const struct ov02a10_mode *mode,
> + struct v4l2_mbus_framefmt *fmt)
> +{
> + fmt->width = mode->width;
> + fmt->height = mode->height;
> + fmt->field = V4L2_FIELD_NONE;
> +}
> +
> +static int ov02a10_set_fmt(struct v4l2_subdev *sd,
> + struct v4l2_subdev_pad_config *cfg,
> + struct v4l2_subdev_format *fmt)
> +{
> + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> + struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
> +
> + mutex_lock(&ov02a10->mutex);
> +
> + if (ov02a10->streaming) {
> + mutex_unlock(&ov02a10->mutex);
> + return -EBUSY;
> + }
> +
> + /* Only one sensor mode supported */
> + mbus_fmt->code = ov02a10->fmt.code;
> + ov02a10_fill_fmt(ov02a10->cur_mode, mbus_fmt);
> + ov02a10->fmt = fmt->format;
> +
> + mutex_unlock(&ov02a10->mutex);
> +
> + return 0;
> +}
> +
> +static int ov02a10_get_fmt(struct v4l2_subdev *sd,
> + struct v4l2_subdev_pad_config *cfg,
> + struct v4l2_subdev_format *fmt)
> +{
> + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> + struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
> +
> + mutex_lock(&ov02a10->mutex);
> +
> + fmt->format = ov02a10->fmt;
> + mbus_fmt->code = ov02a10->fmt.code;
> + ov02a10_fill_fmt(ov02a10->cur_mode, mbus_fmt);
> +
> + mutex_unlock(&ov02a10->mutex);
> +
> + return 0;
> +}
> +
> +static int ov02a10_enum_mbus_code(struct v4l2_subdev *sd,
> + struct v4l2_subdev_pad_config *cfg,
> + struct v4l2_subdev_mbus_code_enum *code)
> +{
> + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +
> + if (code->index >= ARRAY_SIZE(supported_modes))
> + return -EINVAL;
> +
> + code->code = ov02a10->fmt.code;
> +
> + return 0;
> +}
> +
> +static int ov02a10_enum_frame_sizes(struct v4l2_subdev *sd,
> + struct v4l2_subdev_pad_config *cfg,
> + struct v4l2_subdev_frame_size_enum *fse)
> +{
> + if (fse->index >= ARRAY_SIZE(supported_modes))
> + return -EINVAL;
> +
> + fse->min_width = supported_modes[fse->index].width;
> + fse->max_width = supported_modes[fse->index].width;
> + fse->max_height = supported_modes[fse->index].height;
> + fse->min_height = supported_modes[fse->index].height;
> +
> + return 0;
> +}
> +
> +static int __ov02a10_power_on(struct ov02a10 *ov02a10)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> + struct device *dev = &client->dev;
> + int ret;
> +
> + gpiod_set_value_cansleep(ov02a10->n_rst_gpio, GPIOD_OUT_LOW);
> + gpiod_set_value_cansleep(ov02a10->pd_gpio, GPIOD_OUT_HIGH);
> +
> + ret = clk_prepare_enable(ov02a10->eclk);
> + if (ret < 0) {
> + dev_err(dev, "failed to enable eclk\n");
> + return ret;
> + }
> +
> + ret = regulator_bulk_enable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
> + if (ret < 0) {
> + dev_err(dev, "failed to enable regulators\n");
> + goto disable_clk;
> + }
> + usleep_range(5000, 6000);
> +
> + gpiod_set_value_cansleep(ov02a10->pd_gpio, GPIOD_OUT_LOW);
> + usleep_range(5000, 6000);
> +
> + gpiod_set_value_cansleep(ov02a10->n_rst_gpio, GPIOD_OUT_HIGH);
> + usleep_range(5000, 6000);
> +
> + return 0;
> +
> +disable_clk:
> + clk_disable_unprepare(ov02a10->eclk);
> +
> + return ret;
> +}
> +
> +static void __ov02a10_power_off(struct ov02a10 *ov02a10)
> +{
> + gpiod_set_value_cansleep(ov02a10->n_rst_gpio, 1);
> + clk_disable_unprepare(ov02a10->eclk);
> + gpiod_set_value_cansleep(ov02a10->pd_gpio, 1);
> + regulator_bulk_disable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
> +}
> +
> +static int __ov02a10_start_stream(struct ov02a10 *ov02a10)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> + const struct ov02a10_reg_list *reg_list;
> + int ret;
> +
> + /* Apply default values of current mode */
> + reg_list = &ov02a10->cur_mode->reg_list;
> + ret = ov02a10_write_array(ov02a10, reg_list);
> + if (ret)
> + return ret;
> +
> + /* Apply customized values from user */
> + ret = __v4l2_ctrl_handler_setup(ov02a10->subdev.ctrl_handler);
> + if (ret)
> + return ret;
> +
> + /* Set orientation to 180 degree */
> + if (ov02a10->upside_down) {
> + ret = i2c_smbus_write_byte_data(client, REG_MIRROR_FLIP_CONTROL,
> + REG_MIRROR_FLIP_ENABLE);
> + if (ret) {
> + dev_err(&client->dev, "failed to set orientation\n");
> + return ret;
> + }
> + ret = i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> + REG_ENABLE);
> + if (ret < 0)
> + return ret;
> + }
> +
> + /* Set stream on register */
> + return i2c_smbus_write_byte_data(client,
> + REG_SC_CTRL_MODE, SC_CTRL_MODE_STREAMING);
> +}
> +
> +static int __ov02a10_stop_stream(struct ov02a10 *ov02a10)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +
> + return i2c_smbus_write_byte_data(client,
> + REG_SC_CTRL_MODE, SC_CTRL_MODE_STANDBY);
Indentation.
> +}
> +
> +static int ov02a10_entity_init_cfg(struct v4l2_subdev *sd,
> + struct v4l2_subdev_pad_config *cfg)
> +{
> + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> + struct v4l2_subdev_format fmt = { 0 };
> +
> + fmt.which = cfg ? V4L2_SUBDEV_FORMAT_TRY : V4L2_SUBDEV_FORMAT_ACTIVE;
> + fmt.format.width = ov02a10->cur_mode->width;
> + fmt.format.height = ov02a10->cur_mode->width;
> +
> + ov02a10_set_fmt(sd, cfg, &fmt);
> +
> + return 0;
> +}
> +
> +static int ov02a10_s_stream(struct v4l2_subdev *sd, int on)
> +{
> + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> + int ret = 0;
> +
> + dev_dbg(&client->dev, "ov02a10 s_stream (%d)\n", on);
> + mutex_lock(&ov02a10->mutex);
> +
> + if (ov02a10->streaming == on)
> + goto unlock_and_return;
> +
> + if (on) {
> + ret = pm_runtime_get_sync(&client->dev);
> + if (ret < 0) {
> + pm_runtime_put_noidle(&client->dev);
> + goto unlock_and_return;
> + }
> +
> + ret = __ov02a10_start_stream(ov02a10);
> + if (ret) {
> + __ov02a10_stop_stream(ov02a10);
> + ov02a10->streaming = !on;
> + goto err_rpm_put;
> + }
> + } else {
> + __ov02a10_stop_stream(ov02a10);
> + pm_runtime_put(&client->dev);
> + }
> +
> + ov02a10->streaming = on;
> + mutex_unlock(&ov02a10->mutex);
> +
> + return ret;
> +
> +err_rpm_put:
> + pm_runtime_put(&client->dev);
> +unlock_and_return:
> + mutex_unlock(&ov02a10->mutex);
> +
> + return ret;
> +}
> +
> +static int __maybe_unused ov02a10_runtime_resume(struct device *dev)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +
> + return __ov02a10_power_on(ov02a10);
> +}
> +
> +static int __maybe_unused ov02a10_runtime_suspend(struct device *dev)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +
> + __ov02a10_power_off(ov02a10);
> +
> + return 0;
> +}
Please move the content of the both functions here; you don't need another
pair with just different arguments.
> +
> +static const struct dev_pm_ops ov02a10_pm_ops = {
> + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
> + pm_runtime_force_resume)
> + SET_RUNTIME_PM_OPS(ov02a10_runtime_suspend,
> + ov02a10_runtime_resume, NULL)
> +};
> +
> +/*
> + * ov02a10_set_exposure - Function called when setting exposure time
> + * @priv: Pointer to device structure
> + * @val: Variable for exposure time, in the unit of micro-second
> + *
> + * Set exposure time based on input value.
> + *
> + * Return: 0 on success
> + */
> +static int ov02a10_set_exposure(struct ov02a10 *ov02a10, int val)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> + int ret;
> +
> + ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
> + if (ret < 0)
> + return ret;
> +
> + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_EXPOSURE_H,
> + ((val >> OV02A10_EXP_SHIFT) &
> + OV02A10_MASK_8_BITS));
> + if (ret < 0)
> + return ret;
> +
> + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_EXPOSURE_L,
> + (val & OV02A10_MASK_8_BITS));
> + if (ret < 0)
> + return ret;
> +
> + return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> + REG_ENABLE);
> +}
> +
> +static int ov02a10_set_gain(struct ov02a10 *ov02a10, int val)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> + int ret;
> +
> + ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
> + if (ret < 0)
> + return ret;
> +
> + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_GAIN,
> + (val & OV02A10_MASK_8_BITS));
> + if (ret < 0)
> + return ret;
> +
> + return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> + REG_ENABLE);
> +}
> +
> +static int ov02a10_set_vblank(struct ov02a10 *ov02a10, int val)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> + int ret;
> +
> + ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
> + if (ret < 0)
> + return ret;
> +
> + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_VTS_H,
> + (((val + ov02a10->cur_mode->height -
> + OV02A10_BASIC_LINE) >>
> + OV02A10_VTS_SHIFT) &
> + OV02A10_MASK_8_BITS));
> + if (ret < 0)
> + return ret;
> +
> + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_VTS_L,
> + ((val + ov02a10->cur_mode->height -
> + OV02A10_BASIC_LINE) &
> + OV02A10_MASK_8_BITS));
> + if (ret < 0)
> + return ret;
> +
> + return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> + REG_ENABLE);
> +}
> +
> +static int ov02a10_set_test_pattern(struct ov02a10 *ov02a10, int pattern)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> + int ret;
> +
> + if (pattern)
> + pattern = OV02A10_TEST_PATTERN_ENABLE;
> +
> + ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
> + if (ret < 0)
> + return ret;
> +
> + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_TEST_PATTERN,
> + pattern);
> + if (ret < 0)
> + return ret;
> +
> + ret = i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> + REG_ENABLE);
> + if (ret < 0)
> + return ret;
> +
> + return i2c_smbus_write_byte_data(client, REG_SC_CTRL_MODE,
> + SC_CTRL_MODE_STREAMING);
> +}
> +
> +static int ov02a10_set_ctrl(struct v4l2_ctrl *ctrl)
> +{
> + struct ov02a10 *ov02a10 = container_of(ctrl->handler,
> + struct ov02a10, ctrl_handler);
> + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> + s64 max_expo;
> + int ret;
> +
> + /* Propagate change of current control to all related controls */
> + if (ctrl->id == V4L2_CID_VBLANK) {
> + /* Update max exposure while meeting expected vblanking */
> + max_expo = ov02a10->cur_mode->height + ctrl->val -
> + OV02A10_EXPOSURE_MAX_MARGIN;
> + __v4l2_ctrl_modify_range(ov02a10->exposure,
> + ov02a10->exposure->minimum, max_expo,
> + ov02a10->exposure->step,
> + ov02a10->exposure->default_value);
> + }
> +
> + /* V4L2 controls values will be applied only when power is already up */
> + if (!pm_runtime_get_if_in_use(&client->dev))
> + return 0;
> +
> + switch (ctrl->id) {
> + case V4L2_CID_EXPOSURE:
> + ret = ov02a10_set_exposure(ov02a10, ctrl->val);
> + break;
> + case V4L2_CID_ANALOGUE_GAIN:
> + ret = ov02a10_set_gain(ov02a10, ctrl->val);
> + break;
> + case V4L2_CID_VBLANK:
> + ret = ov02a10_set_vblank(ov02a10, ctrl->val);
> + break;
> + case V4L2_CID_TEST_PATTERN:
> + ret = ov02a10_set_test_pattern(ov02a10, ctrl->val);
> + break;
> + };
> +
> + pm_runtime_put(&client->dev);
> +
> + return ret;
> +}
> +
> +static const struct v4l2_subdev_video_ops ov02a10_video_ops = {
> + .s_stream = ov02a10_s_stream,
> +};
> +
> +static const struct v4l2_subdev_pad_ops ov02a10_pad_ops = {
> + .init_cfg = ov02a10_entity_init_cfg,
> + .enum_mbus_code = ov02a10_enum_mbus_code,
> + .enum_frame_size = ov02a10_enum_frame_sizes,
> + .get_fmt = ov02a10_get_fmt,
> + .set_fmt = ov02a10_set_fmt,
> +};
> +
> +static const struct v4l2_subdev_ops ov02a10_subdev_ops = {
> + .video = &ov02a10_video_ops,
> + .pad = &ov02a10_pad_ops,
> +};
> +
> +static const struct media_entity_operations ov02a10_subdev_entity_ops = {
> + .link_validate = v4l2_subdev_link_validate,
> +};
> +
> +static const struct v4l2_ctrl_ops ov02a10_ctrl_ops = {
> + .s_ctrl = ov02a10_set_ctrl,
> +};
> +
> +static int ov02a10_initialize_controls(struct ov02a10 *ov02a10)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> + const struct ov02a10_mode *mode;
> + struct v4l2_ctrl_handler *handler;
> + struct v4l2_ctrl *ctrl;
> + u64 exposure_max;
> + u32 pixel_rate, h_blank;
> + int ret;
> +
> + handler = &ov02a10->ctrl_handler;
> + mode = ov02a10->cur_mode;
> + ret = v4l2_ctrl_handler_init(handler, 7);
> + if (ret)
> + return ret;
> +
> + handler->lock = &ov02a10->mutex;
> +
> + ctrl = v4l2_ctrl_new_int_menu(handler, NULL, V4L2_CID_LINK_FREQ,
> + 0, 0, link_freq_menu_items);
> + if (ctrl)
> + ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> +
> + pixel_rate = to_pixel_rate(0);
> + v4l2_ctrl_new_std(handler, NULL, V4L2_CID_PIXEL_RATE,
> + 0, pixel_rate, 1, pixel_rate);
> +
> + h_blank = mode->hts_def - mode->width;
> + ov02a10->hblank = v4l2_ctrl_new_std(handler, NULL, V4L2_CID_HBLANK,
> + h_blank, h_blank, 1, h_blank);
> + if (ov02a10->hblank)
> + ov02a10->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> +
> + ov02a10->vblank = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> + V4L2_CID_VBLANK, mode->vts_def -
> + mode->height,
> + OV02A10_VTS_MAX - mode->height, 1,
> + mode->vts_def - mode->height);
> +
> + exposure_max = mode->vts_def - 4;
> + ov02a10->exposure = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> + V4L2_CID_EXPOSURE,
> + OV02A10_EXPOSURE_MIN,
> + exposure_max,
> + OV02A10_EXPOSURE_STEP,
> + mode->exp_def);
> +
> + ov02a10->anal_gain = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> + V4L2_CID_ANALOGUE_GAIN,
> + OV02A10_GAIN_MIN,
> + OV02A10_GAIN_MAX,
> + OV02A10_GAIN_STEP,
> + OV02A10_GAIN_DEFAULT);
> +
> + ov02a10->test_pattern =
> + v4l2_ctrl_new_std_menu_items(handler,
> + &ov02a10_ctrl_ops,
> + V4L2_CID_TEST_PATTERN,
> + ARRAY_SIZE(ov02a10_test_pattern_menu) -
> + 1, 0, 0,
> + ov02a10_test_pattern_menu);
> +
> + if (handler->error) {
> + ret = handler->error;
> + dev_err(&client->dev, "failed to init controls(%d)\n", ret);
> + goto err_free_handler;
> + }
> +
> + ov02a10->subdev.ctrl_handler = handler;
> +
> + return 0;
> +
> +err_free_handler:
> + v4l2_ctrl_handler_free(handler);
> +
> + return ret;
> +}
> +
> +static int ov02a10_check_hwcfg(struct device *dev)
> +{
> + struct fwnode_handle *ep;
> + struct fwnode_handle *fwnode = dev_fwnode(dev);
> + struct v4l2_fwnode_endpoint bus_cfg = {
> + .bus_type = V4L2_MBUS_CSI2_DPHY
> + };
> + unsigned int i, j;
> + int ret;
> +
> + if (!fwnode)
> + return -ENXIO;
> +
> + ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
> + if (!ep)
> + return -ENXIO;
> +
> + ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg);
> + fwnode_handle_put(ep);
> + if (ret)
> + return ret;
> +
> + if (!bus_cfg.nr_of_link_frequencies) {
> + dev_err(dev, "no link frequencies defined");
> + ret = -EINVAL;
> + goto check_hwcfg_error;
> + }
> +
> + for (i = 0; i < ARRAY_SIZE(link_freq_menu_items); i++) {
> + for (j = 0; j < bus_cfg.nr_of_link_frequencies; j++) {
> + if (link_freq_menu_items[i] ==
> + bus_cfg.link_frequencies[j])
> + break;
> + }
> +
> + if (j == bus_cfg.nr_of_link_frequencies) {
> + dev_err(dev, "no link frequency %lld supported",
> + link_freq_menu_items[i]);
> + ret = -EINVAL;
> + goto check_hwcfg_error;
> + }
> + }
> +
> +check_hwcfg_error:
> + v4l2_fwnode_endpoint_free(&bus_cfg);
> +
> + return ret;
> +}
> +
> +static int ov02a10_check_sensor_id(struct ov02a10 *ov02a10)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> + u16 id;
> + u8 pid = 0;
> + u8 ver = 0;
> + int ret;
> +
> + /* Check sensor revision */
> + ret = ov02a10_read_smbus(ov02a10, OV02A10_REG_CHIP_ID_H, &pid);
> + if (ret)
> + return ret;
> +
> + ret = ov02a10_read_smbus(ov02a10, OV02A10_REG_CHIP_ID_L, &ver);
> + if (ret)
> + return ret;
> +
> + id = OV02A10_ID(pid, ver);
> + if (id != CHIP_ID) {
> + dev_err(&client->dev, "Unexpected sensor id(%04x)\n", id);
> + return ret;
> + }
> +
> + dev_info(&client->dev, "Detected OV%04X sensor\n", id);
> +
> + return 0;
> +}
> +
> +static int ov02a10_probe(struct i2c_client *client)
> +{
> + struct device *dev = &client->dev;
> + struct ov02a10 *ov02a10;
> + unsigned int rotation;
> + unsigned int i;
> + int ret;
> +
> + dev_info(dev, "ov02a10 probe aaaa++\n");
Please remove.
> +
> + ret = ov02a10_check_hwcfg(dev);
> + if (ret) {
> + dev_err(dev, "failed to check HW configuration: %d",
> + ret);
> + return ret;
> + }
> +
> + ov02a10 = devm_kzalloc(dev, sizeof(*ov02a10), GFP_KERNEL);
> + if (!ov02a10)
> + return -ENOMEM;
> +
> + v4l2_i2c_subdev_init(&ov02a10->subdev, client, &ov02a10_subdev_ops);
> + ov02a10->fmt.code = MEDIA_BUS_FMT_SBGGR10_1X10;
> +
> + /* Optional indication of physical rotation of sensor */
> + ret = fwnode_property_read_u32(dev_fwnode(dev), "rotation",
> + &rotation);
> + if (!ret) {
> + switch (rotation) {
> + case 180:
> + ov02a10->upside_down = true;
> + ov02a10->fmt.code = MEDIA_BUS_FMT_SRGGB10_1X10;
> + break;
> + case 0:
> + break;
> + default:
> + dev_warn(dev, "%u degrees rotation is not supported, ignoring...\n",
> + rotation);
> + }
> + }
> +
> + /* Get system clock (eclk) */
> + ov02a10->eclk = devm_clk_get(dev, "eclk");
> + if (IS_ERR(ov02a10->eclk)) {
> + dev_err(dev, "failed to get eclk\n");
> + return -EINVAL;
> + }
> +
> + ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
> + &ov02a10->eclk_freq);
> + if (ret) {
> + dev_err(dev, "failed to get eclk frequency\n");
> + return ret;
> + }
> +
> + ret = clk_set_rate(ov02a10->eclk, ov02a10->eclk_freq);
> + if (ret) {
> + dev_err(dev, "failed to set eclk frequency (24MHz)\n");
> + return ret;
> + }
> +
> + if (clk_get_rate(ov02a10->eclk) != OV02A10_ECLK_FREQ) {
> + dev_warn(dev, "wrong eclk frequency %d Hz, expected: %d Hz\n",
> + ov02a10->eclk_freq, OV02A10_ECLK_FREQ);
> + return -EINVAL;
> + }
> +
> + ov02a10->pd_gpio = devm_gpiod_get(dev, "powerdown", GPIOD_OUT_HIGH);
> + if (IS_ERR(ov02a10->pd_gpio)) {
> + dev_err(dev, "failed to get powerdown-gpios\n");
> + return -EINVAL;
> + }
> +
> + ov02a10->n_rst_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
> + if (IS_ERR(ov02a10->n_rst_gpio)) {
> + dev_err(dev, "failed to get reset-gpios\n");
> + return -EINVAL;
> + }
> +
> + for (i = 0; i < OV02A10_NUM_SUPPLIES; i++)
> + ov02a10->supplies[i].supply = ov02a10_supply_names[i];
> +
> + ret = devm_regulator_bulk_get(dev,
> + OV02A10_NUM_SUPPLIES,
Fits on a single line.
> + ov02a10->supplies);
> + if (ret) {
> + dev_err(dev, "failed to get regulators\n");
> + return ret;
> + }
> +
> + mutex_init(&ov02a10->mutex);
> + ov02a10->cur_mode = &supported_modes[0];
> + ret = ov02a10_initialize_controls(ov02a10);
> + if (ret) {
> + dev_err(dev, "failed to initialize controls\n");
> + goto err_destroy_mutex;
> + }
> +
> + ret = __ov02a10_power_on(ov02a10);
> + if (ret)
> + goto err_free_handler;
> +
> + ret = ov02a10_check_sensor_id(ov02a10);
> + if (ret)
> + goto err_power_off;
> +
> + ov02a10->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> + ov02a10->subdev.entity.ops = &ov02a10_subdev_entity_ops;
> + ov02a10->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR;
> + ov02a10->pad.flags = MEDIA_PAD_FL_SOURCE;
> + ret = media_entity_pads_init(&ov02a10->subdev.entity, 1, &ov02a10->pad);
> + if (ret < 0) {
> + dev_err(dev, "failed to init entity pads: %d", ret);
> + goto err_power_off;
> + }
> +
> + ret = v4l2_async_register_subdev(&ov02a10->subdev);
> + if (ret) {
> + dev_err(dev, "failed to register V4L2 subdev: %d",
> + ret);
> + goto err_clean_entity;
> + }
> +
> + pm_runtime_set_active(dev);
> + pm_runtime_enable(dev);
> + pm_runtime_idle(dev);
> +
> + dev_info(dev, "ov02a10 probe --\n");
Ditto.
> + return 0;
> +
> +err_clean_entity:
> + media_entity_cleanup(&ov02a10->subdev.entity);
> +err_power_off:
> + __ov02a10_power_off(ov02a10);
> +err_free_handler:
> + v4l2_ctrl_handler_free(ov02a10->subdev.ctrl_handler);
> +err_destroy_mutex:
> + mutex_destroy(&ov02a10->mutex);
> +
> + return ret;
> +}
> +
> +static int ov02a10_remove(struct i2c_client *client)
> +{
> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +
> + v4l2_async_unregister_subdev(sd);
> + media_entity_cleanup(&sd->entity);
> + v4l2_ctrl_handler_free(sd->ctrl_handler);
> + pm_runtime_disable(&client->dev);
> + if (!pm_runtime_status_suspended(&client->dev))
> + __ov02a10_power_off(ov02a10);
> + pm_runtime_set_suspended(&client->dev);
> + mutex_destroy(&ov02a10->mutex);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id ov02a10_of_match[] = {
> + { .compatible = "ovti,ov02a10" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, ov02a10_of_match);
> +
> +static struct i2c_driver ov02a10_i2c_driver = {
> + .driver = {
> + .name = "ov02a10",
> + .pm = &ov02a10_pm_ops,
> + .of_match_table = ov02a10_of_match,
> + },
> + .probe_new = &ov02a10_probe,
> + .remove = &ov02a10_remove,
> +};
> +
> +module_i2c_driver(ov02a10_i2c_driver);
> +
> +MODULE_AUTHOR("Dongchun Zhu <dongchun.zhu@mediatek.com>");
> +MODULE_DESCRIPTION("OmniVision OV02A10 sensor driver");
> +MODULE_LICENSE("GPL v2");
> +
--
Sakari Ailus
sakari.ailus@linux.intel.com
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [V4, 1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10
2019-09-07 9:27 ` [V4, 1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10 dongchun.zhu
2019-09-09 6:46 ` Sakari Ailus
@ 2019-09-09 9:45 ` Andy Shevchenko
2019-09-09 9:57 ` Sakari Ailus
1 sibling, 1 reply; 12+ messages in thread
From: Andy Shevchenko @ 2019-09-09 9:45 UTC (permalink / raw)
To: dongchun.zhu
Cc: mark.rutland, devicetree, drinkcat, srv_heupstream,
shengnan.wang, tfiga, louis.kuo, sj.huang, robh+dt,
linux-mediatek, sakari.ailus, matthias.bgg, bingbu.cao, mchehab,
linux-arm-kernel, linux-media
On Sat, Sep 07, 2019 at 05:27:27PM +0800, dongchun.zhu@mediatek.com wrote:
> From: Dongchun Zhu <dongchun.zhu@mediatek.com>
>
> This patch adds device tree bindings documentation for OV02A10 camera sensor.
>
> Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
> ---
> .../devicetree/bindings/media/i2c/ov02a10.txt | 54 ++++++++++++++++++++++
> MAINTAINERS | 7 +++
This doesn't belong to dt-bindings.
--
With Best Regards,
Andy Shevchenko
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [V4, 1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10
2019-09-09 9:45 ` Andy Shevchenko
@ 2019-09-09 9:57 ` Sakari Ailus
2019-09-09 10:11 ` Andy Shevchenko
0 siblings, 1 reply; 12+ messages in thread
From: Sakari Ailus @ 2019-09-09 9:57 UTC (permalink / raw)
To: Andy Shevchenko
Cc: mark.rutland, devicetree, drinkcat, srv_heupstream,
shengnan.wang, tfiga, louis.kuo, sj.huang, robh+dt,
linux-mediatek, dongchun.zhu, matthias.bgg, bingbu.cao, mchehab,
linux-arm-kernel, linux-media
Hi Andy,
On Mon, Sep 09, 2019 at 12:45:01PM +0300, Andy Shevchenko wrote:
> On Sat, Sep 07, 2019 at 05:27:27PM +0800, dongchun.zhu@mediatek.com wrote:
> > From: Dongchun Zhu <dongchun.zhu@mediatek.com>
> >
> > This patch adds device tree bindings documentation for OV02A10 camera sensor.
> >
> > Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
> > ---
> > .../devicetree/bindings/media/i2c/ov02a10.txt | 54 ++++++++++++++++++++++
>
> > MAINTAINERS | 7 +++
>
> This doesn't belong to dt-bindings.
The practice has been to add the MAINTAINERS entry along with the DT
bindings.
--
Sakari Ailus
sakari.ailus@linux.intel.com
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [V4, 1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10
2019-09-09 9:57 ` Sakari Ailus
@ 2019-09-09 10:11 ` Andy Shevchenko
0 siblings, 0 replies; 12+ messages in thread
From: Andy Shevchenko @ 2019-09-09 10:11 UTC (permalink / raw)
To: Sakari Ailus
Cc: mark.rutland, devicetree, drinkcat, srv_heupstream,
shengnan.wang, tfiga, louis.kuo, sj.huang, robh+dt,
linux-mediatek, dongchun.zhu, matthias.bgg, bingbu.cao, mchehab,
linux-arm-kernel, linux-media
On Mon, Sep 09, 2019 at 12:57:15PM +0300, Sakari Ailus wrote:
> Hi Andy,
>
> On Mon, Sep 09, 2019 at 12:45:01PM +0300, Andy Shevchenko wrote:
> > On Sat, Sep 07, 2019 at 05:27:27PM +0800, dongchun.zhu@mediatek.com wrote:
> > > From: Dongchun Zhu <dongchun.zhu@mediatek.com>
> > >
> > > This patch adds device tree bindings documentation for OV02A10 camera sensor.
> > >
> > > Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
> > > ---
> > > .../devicetree/bindings/media/i2c/ov02a10.txt | 54 ++++++++++++++++++++++
> >
> > > MAINTAINERS | 7 +++
> >
> > This doesn't belong to dt-bindings.
>
> The practice has been to add the MAINTAINERS entry along with the DT
> bindings.
Ah, okay, good to know!
--
With Best Regards,
Andy Shevchenko
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [V4, 2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver
2019-09-09 6:55 ` [V4, 2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver Sakari Ailus
@ 2019-11-04 3:30 ` Dongchun Zhu
0 siblings, 0 replies; 12+ messages in thread
From: Dongchun Zhu @ 2019-11-04 3:30 UTC (permalink / raw)
To: Sakari Ailus
Cc: mark.rutland, drinkcat, andriy.shevchenko, srv_heupstream,
devicetree, shengnan.wang, tfiga, louis.kuo, sj.huang, robh+dt,
linux-mediatek, matthias.bgg, bingbu.cao, mchehab,
linux-arm-kernel, linux-media
Hello Sakari,
On Mon, 2019-09-09 at 09:55 +0300, Sakari Ailus wrote:
> Hi Dongchun,
>
> Thanks for the update. A few more comments below.
>
> On Sat, Sep 07, 2019 at 05:27:28PM +0800, dongchun.zhu@mediatek.com wrote:
> > From: Dongchun Zhu <dongchun.zhu@mediatek.com>
> >
> > This patch adds a V4L2 sub-device driver for OV02A10 image sensor.
> > The OV02A10 is a 1/5" CMOS sensor from Omnivision,
> > supporting output format: 10-bit Raw.
> >
> > The OV02A10 has a single MIPI lane interface and use the I2C bus
> > for control and the CSI-2 bus for data.
> >
> > Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
> > ---
> > MAINTAINERS | 1 +
> > drivers/media/i2c/Kconfig | 11 +
> > drivers/media/i2c/Makefile | 1 +
> > drivers/media/i2c/ov02a10.c | 1062 +++++++++++++++++++++++++++++++++++++++++++
> > 4 files changed, 1075 insertions(+)
> > create mode 100644 drivers/media/i2c/ov02a10.c
> >
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index 41734fb..4b714a2 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -11821,6 +11821,7 @@ M: Dongchun Zhu <dongchun.zhu@mediatek.com>
> > L: linux-media@vger.kernel.org
> > T: git git://linuxtv.org/media_tree.git
> > S: Maintained
> > +F: drivers/media/i2c/ov02a10.c
> > F: Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> >
> > OMNIVISION OV2680 SENSOR DRIVER
> > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> > index 79ce9ec..22e0db4 100644
> > --- a/drivers/media/i2c/Kconfig
> > +++ b/drivers/media/i2c/Kconfig
> > @@ -617,6 +617,17 @@ config VIDEO_IMX355
> > To compile this driver as a module, choose M here: the
> > module will be called imx355.
> >
> > +config VIDEO_OV02A10
> > + tristate "OmniVision OV02A10 sensor support"
> > + depends on VIDEO_V4L2 && I2C
> > + depends on MEDIA_CAMERA_SUPPORT
>
> Please add VIDEO_V4L2_SUBDEV_API
>
Fixed in next release.
> > + help
> > + This is a Video4Linux2 sensor driver for the OmniVision
> > + OV02A10 camera.
> > +
> > + To compile this driver as a module, choose M here: the
> > + module will be called ov02a10.
> > +
> > config VIDEO_OV2640
> > tristate "OmniVision OV2640 sensor support"
> > depends on VIDEO_V4L2 && I2C
> > diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> > index fd4ea86..d27f4e2 100644
> > --- a/drivers/media/i2c/Makefile
> > +++ b/drivers/media/i2c/Makefile
> > @@ -63,6 +63,7 @@ obj-$(CONFIG_VIDEO_VP27SMPX) += vp27smpx.o
> > obj-$(CONFIG_VIDEO_SONY_BTF_MPX) += sony-btf-mpx.o
> > obj-$(CONFIG_VIDEO_UPD64031A) += upd64031a.o
> > obj-$(CONFIG_VIDEO_UPD64083) += upd64083.o
> > +obj-$(CONFIG_VIDEO_OV02A10) += ov02a10.o
> > obj-$(CONFIG_VIDEO_OV2640) += ov2640.o
> > obj-$(CONFIG_VIDEO_OV2680) += ov2680.o
> > obj-$(CONFIG_VIDEO_OV2685) += ov2685.o
> > diff --git a/drivers/media/i2c/ov02a10.c b/drivers/media/i2c/ov02a10.c
> > new file mode 100644
> > index 0000000..fb677d5
> > --- /dev/null
> > +++ b/drivers/media/i2c/ov02a10.c
> > @@ -0,0 +1,1062 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +// Copyright (c) 2019 MediaTek Inc.
> > +
> > +#include <linux/clk.h>
> > +#include <linux/device.h>
> > +#include <linux/delay.h>
> > +#include <linux/gpio/consumer.h>
> > +#include <linux/i2c.h>
> > +#include <linux/module.h>
> > +#include <linux/pm_runtime.h>
> > +#include <linux/regulator/consumer.h>
> > +#include <media/media-entity.h>
> > +#include <media/v4l2-async.h>
> > +#include <media/v4l2-ctrls.h>
> > +#include <media/v4l2-subdev.h>
> > +#include <media/v4l2-fwnode.h>
> > +
> > +#define CHIP_ID 0x2509
> > +#define OV02A10_REG_CHIP_ID_H 0x02
> > +#define OV02A10_REG_CHIP_ID_L 0x03
> > +#define OV02A10_ID(_msb, _lsb) ((_msb) << 8 | (_lsb))
> > +
> > +/* Bit[1] vertical upside down */
> > +/* Bit[0] horizontal mirror */
> > +#define REG_MIRROR_FLIP_CONTROL 0x3f
> > +
> > +/* Orientation */
> > +#define REG_MIRROR_FLIP_ENABLE 0x03
> > +
> > +#define REG_PAGE_SWITCH 0xfd
> > +#define REG_GLOBAL_EFFECTIVE 0x01
> > +#define REG_ENABLE BIT(0)
> > +#define OV02A10_MASK_8_BITS 0xff
> > +
> > +#define REG_SC_CTRL_MODE 0xac
> > +#define SC_CTRL_MODE_STANDBY 0x00
> > +#define SC_CTRL_MODE_STREAMING 0x01
> > +
> > +#define OV02A10_EXP_SHIFT 8
> > +#define OV02A10_REG_EXPOSURE_H 0x03
> > +#define OV02A10_REG_EXPOSURE_L 0x04
> > +#define OV02A10_EXPOSURE_MIN 4
> > +#define OV02A10_EXPOSURE_MAX_MARGIN 4
> > +#define OV02A10_EXPOSURE_STEP 1
> > +
> > +#define OV02A10_VTS_SHIFT 8
> > +#define OV02A10_REG_VTS_H 0x05
> > +#define OV02A10_REG_VTS_L 0x06
> > +#define OV02A10_VTS_MAX 0x209f
> > +#define OV02A10_VTS_MIN 0x04cf
> > +#define OV02A10_BASIC_LINE 1224
> > +
> > +#define OV02A10_REG_GAIN 0x24
> > +#define OV02A10_GAIN_MIN 0x10
> > +#define OV02A10_GAIN_MAX 0xf8
> > +#define OV02A10_GAIN_STEP 0x01
> > +#define OV02A10_GAIN_DEFAULT 0x40
> > +
> > +/* Test pattern control */
> > +#define OV02A10_REG_TEST_PATTERN 0xb6
> > +#define OV02A10_TEST_PATTERN_ENABLE BIT(0)
> > +
> > +#define OV02A10_LINK_FREQ_390MHZ 390000000ULL
> > +#define OV02A10_ECLK_FREQ 24000000
> > +#define OV02A10_DATA_LANES 1
> > +#define OV02A10_BITS_PER_SAMPLE 10
> > +
> > +static const char * const ov02a10_supply_names[] = {
> > + "dovdd", /* Digital I/O power */
> > + "avdd", /* Analog power */
> > + "dvdd", /* Digital core power */
> > +};
> > +
> > +#define OV02A10_NUM_SUPPLIES ARRAY_SIZE(ov02a10_supply_names)
> > +
> > +struct ov02a10_reg {
> > + u8 addr;
> > + u8 val;
> > +};
> > +
> > +struct ov02a10_reg_list {
> > + u32 num_of_regs;
> > + const struct ov02a10_reg *regs;
> > +};
> > +
> > +struct ov02a10_mode {
> > + u32 width;
> > + u32 height;
> > + u32 exp_def;
> > + u32 hts_def;
> > + u32 vts_def;
> > + const struct ov02a10_reg_list reg_list;
> > +};
> > +
> > +struct ov02a10 {
> > + struct clk *eclk;
> > + u32 eclk_freq;
> > +
> > + struct gpio_desc *pd_gpio;
> > + struct gpio_desc *n_rst_gpio;
> > + struct regulator_bulk_data supplies[OV02A10_NUM_SUPPLIES];
> > +
> > + bool streaming;
> > + bool upside_down;
> > +
> > + /*
> > + * Serialize control access, get/set format, get selection
> > + * and start streaming.
> > + */
> > + struct mutex mutex;
> > + struct v4l2_subdev subdev;
> > + struct media_pad pad;
> > + struct v4l2_ctrl *anal_gain;
> > + struct v4l2_ctrl *exposure;
> > + struct v4l2_ctrl *hblank;
> > + struct v4l2_ctrl *vblank;
> > + struct v4l2_ctrl *hflip;
> > + struct v4l2_ctrl *vflip;
> > + struct v4l2_ctrl *test_pattern;
>
> Of the above references to controls, only exposure appears to be actually
> used. Please drop the others.
>
Thanks for reminder.
We found that hblank, vblank, test_pattern are also used in
ov02a10_initialize_controls.
And hflip and vflip would be dropped in next release.
> > + struct v4l2_mbus_framefmt fmt;
> > + struct v4l2_ctrl_handler ctrl_handler;
> > +
> > + const struct ov02a10_mode *cur_mode;
> > +};
> > +
> > +static inline struct ov02a10 *to_ov02a10(struct v4l2_subdev *sd)
> > +{
> > + return container_of(sd, struct ov02a10, subdev);
> > +}
> > +
> > +/*
> > + * eclk 24Mhz
> > + * pclk 39Mhz
> > + * linelength 934(0x3a6)
> > + * framelength 1390(0x56E)
> > + * grabwindow_width 1600
> > + * grabwindow_height 1200
> > + * max_framerate 30fps
> > + * mipi_datarate per lane 780Mbps
> > + */
> > +static const struct ov02a10_reg ov02a10_1600x1200_regs[] = {
> > + {0xfd, 0x01},
> > + {0xac, 0x00},
> > + {0xfd, 0x00},
> > + {0x2f, 0x29},
> > + {0x34, 0x00},
> > + {0x35, 0x21},
> > + {0x30, 0x15},
> > + {0x33, 0x01},
> > + {0xfd, 0x01},
> > + {0x44, 0x00},
> > + {0x2a, 0x4c},
> > + {0x2b, 0x1e},
> > + {0x2c, 0x60},
> > + {0x25, 0x11},
> > + {0x03, 0x01},
> > + {0x04, 0xae},
> > + {0x09, 0x00},
> > + {0x0a, 0x02},
> > + {0x06, 0xa6},
> > + {0x31, 0x00},
> > + {0x24, 0x40},
> > + {0x01, 0x01},
> > + {0xfb, 0x73},
> > + {0xfd, 0x01},
> > + {0x16, 0x04},
> > + {0x1c, 0x09},
> > + {0x21, 0x42},
> > + {0x12, 0x04},
> > + {0x13, 0x10},
> > + {0x11, 0x40},
> > + {0x33, 0x81},
> > + {0xd0, 0x00},
> > + {0xd1, 0x01},
> > + {0xd2, 0x00},
> > + {0x50, 0x10},
> > + {0x51, 0x23},
> > + {0x52, 0x20},
> > + {0x53, 0x10},
> > + {0x54, 0x02},
> > + {0x55, 0x20},
> > + {0x56, 0x02},
> > + {0x58, 0x48},
> > + {0x5d, 0x15},
> > + {0x5e, 0x05},
> > + {0x66, 0x66},
> > + {0x68, 0x68},
> > + {0x6b, 0x00},
> > + {0x6c, 0x00},
> > + {0x6f, 0x40},
> > + {0x70, 0x40},
> > + {0x71, 0x0a},
> > + {0x72, 0xf0},
> > + {0x73, 0x10},
> > + {0x75, 0x80},
> > + {0x76, 0x10},
> > + {0x84, 0x00},
> > + {0x85, 0x10},
> > + {0x86, 0x10},
> > + {0x87, 0x00},
> > + {0x8a, 0x22},
> > + {0x8b, 0x22},
> > + {0x19, 0xf1},
> > + {0x29, 0x01},
> > + {0xfd, 0x01},
> > + {0x9d, 0xd6},
> > + {0xa0, 0x29},
> > + {0xa1, 0x03},
> > + {0xad, 0x62},
> > + {0xae, 0x00},
> > + {0xaf, 0x85},
> > + {0xb1, 0x01},
> > + {0x8e, 0x06},
> > + {0x8f, 0x40},
> > + {0x90, 0x04},
> > + {0x91, 0xb0},
> > + {0x45, 0x01},
> > + {0x46, 0x00},
> > + {0x47, 0x6c},
> > + {0x48, 0x03},
> > + {0x49, 0x8b},
> > + {0x4a, 0x00},
> > + {0x4b, 0x07},
> > + {0x4c, 0x04},
> > + {0x4d, 0xb7},
> > + {0xf0, 0x40},
> > + {0xf1, 0x40},
> > + {0xf2, 0x40},
> > + {0xf3, 0x40},
> > + {0x3f, 0x00},
> > + {0xfd, 0x01},
> > + {0x05, 0x00},
> > + {0x06, 0xa6},
> > + {0xfd, 0x01},
> > +};
> > +
> > +static const char * const ov02a10_test_pattern_menu[] = {
> > + "Disabled",
> > + "Color Bar",
> > +};
> > +
> > +static const s64 link_freq_menu_items[] = {
> > + OV02A10_LINK_FREQ_390MHZ
> > +};
> > +
> > +static u64 to_pixel_rate(u32 f_index)
> > +{
> > + u64 pixel_rate = link_freq_menu_items[f_index] * 2 * OV02A10_DATA_LANES;
> > +
> > + do_div(pixel_rate, OV02A10_BITS_PER_SAMPLE);
> > +
> > + return pixel_rate;
> > +}
> > +
> > +static const struct ov02a10_mode supported_modes[] = {
> > + {
> > + .width = 1600,
> > + .height = 1200,
> > + .exp_def = 0x01ae,
> > + .hts_def = 0x03a6,
> > + .vts_def = 0x056e,
> > + .reg_list = {
> > + .num_of_regs = ARRAY_SIZE(ov02a10_1600x1200_regs),
> > + .regs = ov02a10_1600x1200_regs,
> > + },
> > + },
> > +};
> > +
> > +static int ov02a10_write_array(struct ov02a10 *ov02a10,
> > + const struct ov02a10_reg_list *r_list)
> > +{
> > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > + unsigned int i;
> > + int ret;
> > +
> > + for (i = 0; i < r_list->num_of_regs; i++) {
> > + ret = i2c_smbus_write_byte_data(client,
> > + r_list->regs[i].addr,
> > + r_list->regs[i].val);
> > + if (ret < 0)
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int ov02a10_read_smbus(struct ov02a10 *ov02a10, unsigned char reg,
> > + unsigned char *val)
> > +{
> > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > + int ret;
> > +
> > + ret = i2c_smbus_read_byte_data(client, reg);
> > + if (ret >= 0) {
> > + *val = (unsigned char)ret;
> > + ret = 0;
> > + }
> > +
> > + return ret;
> > +}
> > +
> > +static void ov02a10_fill_fmt(const struct ov02a10_mode *mode,
> > + struct v4l2_mbus_framefmt *fmt)
> > +{
> > + fmt->width = mode->width;
> > + fmt->height = mode->height;
> > + fmt->field = V4L2_FIELD_NONE;
> > +}
> > +
> > +static int ov02a10_set_fmt(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_format *fmt)
> > +{
> > + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > + struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
> > +
> > + mutex_lock(&ov02a10->mutex);
> > +
> > + if (ov02a10->streaming) {
> > + mutex_unlock(&ov02a10->mutex);
> > + return -EBUSY;
> > + }
> > +
> > + /* Only one sensor mode supported */
> > + mbus_fmt->code = ov02a10->fmt.code;
> > + ov02a10_fill_fmt(ov02a10->cur_mode, mbus_fmt);
> > + ov02a10->fmt = fmt->format;
> > +
> > + mutex_unlock(&ov02a10->mutex);
> > +
> > + return 0;
> > +}
> > +
> > +static int ov02a10_get_fmt(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_format *fmt)
> > +{
> > + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > + struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
> > +
> > + mutex_lock(&ov02a10->mutex);
> > +
> > + fmt->format = ov02a10->fmt;
> > + mbus_fmt->code = ov02a10->fmt.code;
> > + ov02a10_fill_fmt(ov02a10->cur_mode, mbus_fmt);
> > +
> > + mutex_unlock(&ov02a10->mutex);
> > +
> > + return 0;
> > +}
> > +
> > +static int ov02a10_enum_mbus_code(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_mbus_code_enum *code)
> > +{
> > + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > +
> > + if (code->index >= ARRAY_SIZE(supported_modes))
> > + return -EINVAL;
> > +
> > + code->code = ov02a10->fmt.code;
> > +
> > + return 0;
> > +}
> > +
> > +static int ov02a10_enum_frame_sizes(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_frame_size_enum *fse)
> > +{
> > + if (fse->index >= ARRAY_SIZE(supported_modes))
> > + return -EINVAL;
> > +
> > + fse->min_width = supported_modes[fse->index].width;
> > + fse->max_width = supported_modes[fse->index].width;
> > + fse->max_height = supported_modes[fse->index].height;
> > + fse->min_height = supported_modes[fse->index].height;
> > +
> > + return 0;
> > +}
> > +
> > +static int __ov02a10_power_on(struct ov02a10 *ov02a10)
> > +{
> > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > + struct device *dev = &client->dev;
> > + int ret;
> > +
> > + gpiod_set_value_cansleep(ov02a10->n_rst_gpio, GPIOD_OUT_LOW);
> > + gpiod_set_value_cansleep(ov02a10->pd_gpio, GPIOD_OUT_HIGH);
> > +
> > + ret = clk_prepare_enable(ov02a10->eclk);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to enable eclk\n");
> > + return ret;
> > + }
> > +
> > + ret = regulator_bulk_enable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to enable regulators\n");
> > + goto disable_clk;
> > + }
> > + usleep_range(5000, 6000);
> > +
> > + gpiod_set_value_cansleep(ov02a10->pd_gpio, GPIOD_OUT_LOW);
> > + usleep_range(5000, 6000);
> > +
> > + gpiod_set_value_cansleep(ov02a10->n_rst_gpio, GPIOD_OUT_HIGH);
> > + usleep_range(5000, 6000);
> > +
> > + return 0;
> > +
> > +disable_clk:
> > + clk_disable_unprepare(ov02a10->eclk);
> > +
> > + return ret;
> > +}
> > +
> > +static void __ov02a10_power_off(struct ov02a10 *ov02a10)
> > +{
> > + gpiod_set_value_cansleep(ov02a10->n_rst_gpio, 1);
> > + clk_disable_unprepare(ov02a10->eclk);
> > + gpiod_set_value_cansleep(ov02a10->pd_gpio, 1);
> > + regulator_bulk_disable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
> > +}
> > +
> > +static int __ov02a10_start_stream(struct ov02a10 *ov02a10)
> > +{
> > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > + const struct ov02a10_reg_list *reg_list;
> > + int ret;
> > +
> > + /* Apply default values of current mode */
> > + reg_list = &ov02a10->cur_mode->reg_list;
> > + ret = ov02a10_write_array(ov02a10, reg_list);
> > + if (ret)
> > + return ret;
> > +
> > + /* Apply customized values from user */
> > + ret = __v4l2_ctrl_handler_setup(ov02a10->subdev.ctrl_handler);
> > + if (ret)
> > + return ret;
> > +
> > + /* Set orientation to 180 degree */
> > + if (ov02a10->upside_down) {
> > + ret = i2c_smbus_write_byte_data(client, REG_MIRROR_FLIP_CONTROL,
> > + REG_MIRROR_FLIP_ENABLE);
> > + if (ret) {
> > + dev_err(&client->dev, "failed to set orientation\n");
> > + return ret;
> > + }
> > + ret = i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> > + REG_ENABLE);
> > + if (ret < 0)
> > + return ret;
> > + }
> > +
> > + /* Set stream on register */
> > + return i2c_smbus_write_byte_data(client,
> > + REG_SC_CTRL_MODE, SC_CTRL_MODE_STREAMING);
> > +}
> > +
> > +static int __ov02a10_stop_stream(struct ov02a10 *ov02a10)
> > +{
> > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > +
> > + return i2c_smbus_write_byte_data(client,
> > + REG_SC_CTRL_MODE, SC_CTRL_MODE_STANDBY);
>
> Indentation.
>
Fixed in next release.
> > +}
> > +
> > +static int ov02a10_entity_init_cfg(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg)
> > +{
> > + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > + struct v4l2_subdev_format fmt = { 0 };
> > +
> > + fmt.which = cfg ? V4L2_SUBDEV_FORMAT_TRY : V4L2_SUBDEV_FORMAT_ACTIVE;
> > + fmt.format.width = ov02a10->cur_mode->width;
> > + fmt.format.height = ov02a10->cur_mode->width;
> > +
> > + ov02a10_set_fmt(sd, cfg, &fmt);
> > +
> > + return 0;
> > +}
> > +
> > +static int ov02a10_s_stream(struct v4l2_subdev *sd, int on)
> > +{
> > + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > + int ret = 0;
> > +
> > + dev_dbg(&client->dev, "ov02a10 s_stream (%d)\n", on);
> > + mutex_lock(&ov02a10->mutex);
> > +
> > + if (ov02a10->streaming == on)
> > + goto unlock_and_return;
> > +
> > + if (on) {
> > + ret = pm_runtime_get_sync(&client->dev);
> > + if (ret < 0) {
> > + pm_runtime_put_noidle(&client->dev);
> > + goto unlock_and_return;
> > + }
> > +
> > + ret = __ov02a10_start_stream(ov02a10);
> > + if (ret) {
> > + __ov02a10_stop_stream(ov02a10);
> > + ov02a10->streaming = !on;
> > + goto err_rpm_put;
> > + }
> > + } else {
> > + __ov02a10_stop_stream(ov02a10);
> > + pm_runtime_put(&client->dev);
> > + }
> > +
> > + ov02a10->streaming = on;
> > + mutex_unlock(&ov02a10->mutex);
> > +
> > + return ret;
> > +
> > +err_rpm_put:
> > + pm_runtime_put(&client->dev);
> > +unlock_and_return:
> > + mutex_unlock(&ov02a10->mutex);
> > +
> > + return ret;
> > +}
> > +
> > +static int __maybe_unused ov02a10_runtime_resume(struct device *dev)
> > +{
> > + struct i2c_client *client = to_i2c_client(dev);
> > + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> > + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > +
> > + return __ov02a10_power_on(ov02a10);
> > +}
> > +
> > +static int __maybe_unused ov02a10_runtime_suspend(struct device *dev)
> > +{
> > + struct i2c_client *client = to_i2c_client(dev);
> > + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> > + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > +
> > + __ov02a10_power_off(ov02a10);
> > +
> > + return 0;
> > +}
>
> Please move the content of the both functions here; you don't need another
> pair with just different arguments.
>
Good idea.
We would move the code of power on and off directly to the resume and
suspend callbacks in next release.
> > +
> > +static const struct dev_pm_ops ov02a10_pm_ops = {
> > + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
> > + pm_runtime_force_resume)
> > + SET_RUNTIME_PM_OPS(ov02a10_runtime_suspend,
> > + ov02a10_runtime_resume, NULL)
> > +};
> > +
> > +/*
> > + * ov02a10_set_exposure - Function called when setting exposure time
> > + * @priv: Pointer to device structure
> > + * @val: Variable for exposure time, in the unit of micro-second
> > + *
> > + * Set exposure time based on input value.
> > + *
> > + * Return: 0 on success
> > + */
> > +static int ov02a10_set_exposure(struct ov02a10 *ov02a10, int val)
> > +{
> > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > + int ret;
> > +
> > + ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_EXPOSURE_H,
> > + ((val >> OV02A10_EXP_SHIFT) &
> > + OV02A10_MASK_8_BITS));
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_EXPOSURE_L,
> > + (val & OV02A10_MASK_8_BITS));
> > + if (ret < 0)
> > + return ret;
> > +
> > + return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> > + REG_ENABLE);
> > +}
> > +
> > +static int ov02a10_set_gain(struct ov02a10 *ov02a10, int val)
> > +{
> > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > + int ret;
> > +
> > + ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_GAIN,
> > + (val & OV02A10_MASK_8_BITS));
> > + if (ret < 0)
> > + return ret;
> > +
> > + return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> > + REG_ENABLE);
> > +}
> > +
> > +static int ov02a10_set_vblank(struct ov02a10 *ov02a10, int val)
> > +{
> > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > + int ret;
> > +
> > + ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_VTS_H,
> > + (((val + ov02a10->cur_mode->height -
> > + OV02A10_BASIC_LINE) >>
> > + OV02A10_VTS_SHIFT) &
> > + OV02A10_MASK_8_BITS));
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_VTS_L,
> > + ((val + ov02a10->cur_mode->height -
> > + OV02A10_BASIC_LINE) &
> > + OV02A10_MASK_8_BITS));
> > + if (ret < 0)
> > + return ret;
> > +
> > + return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> > + REG_ENABLE);
> > +}
> > +
> > +static int ov02a10_set_test_pattern(struct ov02a10 *ov02a10, int pattern)
> > +{
> > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > + int ret;
> > +
> > + if (pattern)
> > + pattern = OV02A10_TEST_PATTERN_ENABLE;
> > +
> > + ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_TEST_PATTERN,
> > + pattern);
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> > + REG_ENABLE);
> > + if (ret < 0)
> > + return ret;
> > +
> > + return i2c_smbus_write_byte_data(client, REG_SC_CTRL_MODE,
> > + SC_CTRL_MODE_STREAMING);
> > +}
> > +
> > +static int ov02a10_set_ctrl(struct v4l2_ctrl *ctrl)
> > +{
> > + struct ov02a10 *ov02a10 = container_of(ctrl->handler,
> > + struct ov02a10, ctrl_handler);
> > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > + s64 max_expo;
> > + int ret;
> > +
> > + /* Propagate change of current control to all related controls */
> > + if (ctrl->id == V4L2_CID_VBLANK) {
> > + /* Update max exposure while meeting expected vblanking */
> > + max_expo = ov02a10->cur_mode->height + ctrl->val -
> > + OV02A10_EXPOSURE_MAX_MARGIN;
> > + __v4l2_ctrl_modify_range(ov02a10->exposure,
> > + ov02a10->exposure->minimum, max_expo,
> > + ov02a10->exposure->step,
> > + ov02a10->exposure->default_value);
> > + }
> > +
> > + /* V4L2 controls values will be applied only when power is already up */
> > + if (!pm_runtime_get_if_in_use(&client->dev))
> > + return 0;
> > +
> > + switch (ctrl->id) {
> > + case V4L2_CID_EXPOSURE:
> > + ret = ov02a10_set_exposure(ov02a10, ctrl->val);
> > + break;
> > + case V4L2_CID_ANALOGUE_GAIN:
> > + ret = ov02a10_set_gain(ov02a10, ctrl->val);
> > + break;
> > + case V4L2_CID_VBLANK:
> > + ret = ov02a10_set_vblank(ov02a10, ctrl->val);
> > + break;
> > + case V4L2_CID_TEST_PATTERN:
> > + ret = ov02a10_set_test_pattern(ov02a10, ctrl->val);
> > + break;
> > + };
> > +
> > + pm_runtime_put(&client->dev);
> > +
> > + return ret;
> > +}
> > +
> > +static const struct v4l2_subdev_video_ops ov02a10_video_ops = {
> > + .s_stream = ov02a10_s_stream,
> > +};
> > +
> > +static const struct v4l2_subdev_pad_ops ov02a10_pad_ops = {
> > + .init_cfg = ov02a10_entity_init_cfg,
> > + .enum_mbus_code = ov02a10_enum_mbus_code,
> > + .enum_frame_size = ov02a10_enum_frame_sizes,
> > + .get_fmt = ov02a10_get_fmt,
> > + .set_fmt = ov02a10_set_fmt,
> > +};
> > +
> > +static const struct v4l2_subdev_ops ov02a10_subdev_ops = {
> > + .video = &ov02a10_video_ops,
> > + .pad = &ov02a10_pad_ops,
> > +};
> > +
> > +static const struct media_entity_operations ov02a10_subdev_entity_ops = {
> > + .link_validate = v4l2_subdev_link_validate,
> > +};
> > +
> > +static const struct v4l2_ctrl_ops ov02a10_ctrl_ops = {
> > + .s_ctrl = ov02a10_set_ctrl,
> > +};
> > +
> > +static int ov02a10_initialize_controls(struct ov02a10 *ov02a10)
> > +{
> > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > + const struct ov02a10_mode *mode;
> > + struct v4l2_ctrl_handler *handler;
> > + struct v4l2_ctrl *ctrl;
> > + u64 exposure_max;
> > + u32 pixel_rate, h_blank;
> > + int ret;
> > +
> > + handler = &ov02a10->ctrl_handler;
> > + mode = ov02a10->cur_mode;
> > + ret = v4l2_ctrl_handler_init(handler, 7);
> > + if (ret)
> > + return ret;
> > +
> > + handler->lock = &ov02a10->mutex;
> > +
> > + ctrl = v4l2_ctrl_new_int_menu(handler, NULL, V4L2_CID_LINK_FREQ,
> > + 0, 0, link_freq_menu_items);
> > + if (ctrl)
> > + ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> > +
> > + pixel_rate = to_pixel_rate(0);
> > + v4l2_ctrl_new_std(handler, NULL, V4L2_CID_PIXEL_RATE,
> > + 0, pixel_rate, 1, pixel_rate);
> > +
> > + h_blank = mode->hts_def - mode->width;
> > + ov02a10->hblank = v4l2_ctrl_new_std(handler, NULL, V4L2_CID_HBLANK,
> > + h_blank, h_blank, 1, h_blank);
> > + if (ov02a10->hblank)
> > + ov02a10->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> > +
> > + ov02a10->vblank = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> > + V4L2_CID_VBLANK, mode->vts_def -
> > + mode->height,
> > + OV02A10_VTS_MAX - mode->height, 1,
> > + mode->vts_def - mode->height);
> > +
> > + exposure_max = mode->vts_def - 4;
> > + ov02a10->exposure = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> > + V4L2_CID_EXPOSURE,
> > + OV02A10_EXPOSURE_MIN,
> > + exposure_max,
> > + OV02A10_EXPOSURE_STEP,
> > + mode->exp_def);
> > +
> > + ov02a10->anal_gain = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> > + V4L2_CID_ANALOGUE_GAIN,
> > + OV02A10_GAIN_MIN,
> > + OV02A10_GAIN_MAX,
> > + OV02A10_GAIN_STEP,
> > + OV02A10_GAIN_DEFAULT);
> > +
> > + ov02a10->test_pattern =
> > + v4l2_ctrl_new_std_menu_items(handler,
> > + &ov02a10_ctrl_ops,
> > + V4L2_CID_TEST_PATTERN,
> > + ARRAY_SIZE(ov02a10_test_pattern_menu) -
> > + 1, 0, 0,
> > + ov02a10_test_pattern_menu);
> > +
> > + if (handler->error) {
> > + ret = handler->error;
> > + dev_err(&client->dev, "failed to init controls(%d)\n", ret);
> > + goto err_free_handler;
> > + }
> > +
> > + ov02a10->subdev.ctrl_handler = handler;
> > +
> > + return 0;
> > +
> > +err_free_handler:
> > + v4l2_ctrl_handler_free(handler);
> > +
> > + return ret;
> > +}
> > +
> > +static int ov02a10_check_hwcfg(struct device *dev)
> > +{
> > + struct fwnode_handle *ep;
> > + struct fwnode_handle *fwnode = dev_fwnode(dev);
> > + struct v4l2_fwnode_endpoint bus_cfg = {
> > + .bus_type = V4L2_MBUS_CSI2_DPHY
> > + };
> > + unsigned int i, j;
> > + int ret;
> > +
> > + if (!fwnode)
> > + return -ENXIO;
> > +
> > + ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
> > + if (!ep)
> > + return -ENXIO;
> > +
> > + ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg);
> > + fwnode_handle_put(ep);
> > + if (ret)
> > + return ret;
> > +
> > + if (!bus_cfg.nr_of_link_frequencies) {
> > + dev_err(dev, "no link frequencies defined");
> > + ret = -EINVAL;
> > + goto check_hwcfg_error;
> > + }
> > +
> > + for (i = 0; i < ARRAY_SIZE(link_freq_menu_items); i++) {
> > + for (j = 0; j < bus_cfg.nr_of_link_frequencies; j++) {
> > + if (link_freq_menu_items[i] ==
> > + bus_cfg.link_frequencies[j])
> > + break;
> > + }
> > +
> > + if (j == bus_cfg.nr_of_link_frequencies) {
> > + dev_err(dev, "no link frequency %lld supported",
> > + link_freq_menu_items[i]);
> > + ret = -EINVAL;
> > + goto check_hwcfg_error;
> > + }
> > + }
> > +
> > +check_hwcfg_error:
> > + v4l2_fwnode_endpoint_free(&bus_cfg);
> > +
> > + return ret;
> > +}
> > +
> > +static int ov02a10_check_sensor_id(struct ov02a10 *ov02a10)
> > +{
> > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > + u16 id;
> > + u8 pid = 0;
> > + u8 ver = 0;
> > + int ret;
> > +
> > + /* Check sensor revision */
> > + ret = ov02a10_read_smbus(ov02a10, OV02A10_REG_CHIP_ID_H, &pid);
> > + if (ret)
> > + return ret;
> > +
> > + ret = ov02a10_read_smbus(ov02a10, OV02A10_REG_CHIP_ID_L, &ver);
> > + if (ret)
> > + return ret;
> > +
> > + id = OV02A10_ID(pid, ver);
> > + if (id != CHIP_ID) {
> > + dev_err(&client->dev, "Unexpected sensor id(%04x)\n", id);
> > + return ret;
> > + }
> > +
> > + dev_info(&client->dev, "Detected OV%04X sensor\n", id);
> > +
> > + return 0;
> > +}
> > +
> > +static int ov02a10_probe(struct i2c_client *client)
> > +{
> > + struct device *dev = &client->dev;
> > + struct ov02a10 *ov02a10;
> > + unsigned int rotation;
> > + unsigned int i;
> > + int ret;
> > +
> > + dev_info(dev, "ov02a10 probe aaaa++\n");
>
> Please remove.
>
Fixed in next release.
> > +
> > + ret = ov02a10_check_hwcfg(dev);
> > + if (ret) {
> > + dev_err(dev, "failed to check HW configuration: %d",
> > + ret);
> > + return ret;
> > + }
> > +
> > + ov02a10 = devm_kzalloc(dev, sizeof(*ov02a10), GFP_KERNEL);
> > + if (!ov02a10)
> > + return -ENOMEM;
> > +
> > + v4l2_i2c_subdev_init(&ov02a10->subdev, client, &ov02a10_subdev_ops);
> > + ov02a10->fmt.code = MEDIA_BUS_FMT_SBGGR10_1X10;
> > +
> > + /* Optional indication of physical rotation of sensor */
> > + ret = fwnode_property_read_u32(dev_fwnode(dev), "rotation",
> > + &rotation);
> > + if (!ret) {
> > + switch (rotation) {
> > + case 180:
> > + ov02a10->upside_down = true;
> > + ov02a10->fmt.code = MEDIA_BUS_FMT_SRGGB10_1X10;
> > + break;
> > + case 0:
> > + break;
> > + default:
> > + dev_warn(dev, "%u degrees rotation is not supported, ignoring...\n",
> > + rotation);
> > + }
> > + }
> > +
> > + /* Get system clock (eclk) */
> > + ov02a10->eclk = devm_clk_get(dev, "eclk");
> > + if (IS_ERR(ov02a10->eclk)) {
> > + dev_err(dev, "failed to get eclk\n");
> > + return -EINVAL;
> > + }
> > +
> > + ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
> > + &ov02a10->eclk_freq);
> > + if (ret) {
> > + dev_err(dev, "failed to get eclk frequency\n");
> > + return ret;
> > + }
> > +
> > + ret = clk_set_rate(ov02a10->eclk, ov02a10->eclk_freq);
> > + if (ret) {
> > + dev_err(dev, "failed to set eclk frequency (24MHz)\n");
> > + return ret;
> > + }
> > +
> > + if (clk_get_rate(ov02a10->eclk) != OV02A10_ECLK_FREQ) {
> > + dev_warn(dev, "wrong eclk frequency %d Hz, expected: %d Hz\n",
> > + ov02a10->eclk_freq, OV02A10_ECLK_FREQ);
> > + return -EINVAL;
> > + }
> > +
> > + ov02a10->pd_gpio = devm_gpiod_get(dev, "powerdown", GPIOD_OUT_HIGH);
> > + if (IS_ERR(ov02a10->pd_gpio)) {
> > + dev_err(dev, "failed to get powerdown-gpios\n");
> > + return -EINVAL;
> > + }
> > +
> > + ov02a10->n_rst_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
> > + if (IS_ERR(ov02a10->n_rst_gpio)) {
> > + dev_err(dev, "failed to get reset-gpios\n");
> > + return -EINVAL;
> > + }
> > +
> > + for (i = 0; i < OV02A10_NUM_SUPPLIES; i++)
> > + ov02a10->supplies[i].supply = ov02a10_supply_names[i];
> > +
> > + ret = devm_regulator_bulk_get(dev,
> > + OV02A10_NUM_SUPPLIES,
>
> Fits on a single line.
>
Fixed in next release.
> > + ov02a10->supplies);
> > + if (ret) {
> > + dev_err(dev, "failed to get regulators\n");
> > + return ret;
> > + }
> > +
> > + mutex_init(&ov02a10->mutex);
> > + ov02a10->cur_mode = &supported_modes[0];
> > + ret = ov02a10_initialize_controls(ov02a10);
> > + if (ret) {
> > + dev_err(dev, "failed to initialize controls\n");
> > + goto err_destroy_mutex;
> > + }
> > +
> > + ret = __ov02a10_power_on(ov02a10);
> > + if (ret)
> > + goto err_free_handler;
> > +
> > + ret = ov02a10_check_sensor_id(ov02a10);
> > + if (ret)
> > + goto err_power_off;
> > +
> > + ov02a10->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> > + ov02a10->subdev.entity.ops = &ov02a10_subdev_entity_ops;
> > + ov02a10->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR;
> > + ov02a10->pad.flags = MEDIA_PAD_FL_SOURCE;
> > + ret = media_entity_pads_init(&ov02a10->subdev.entity, 1, &ov02a10->pad);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to init entity pads: %d", ret);
> > + goto err_power_off;
> > + }
> > +
> > + ret = v4l2_async_register_subdev(&ov02a10->subdev);
> > + if (ret) {
> > + dev_err(dev, "failed to register V4L2 subdev: %d",
> > + ret);
> > + goto err_clean_entity;
> > + }
> > +
> > + pm_runtime_set_active(dev);
> > + pm_runtime_enable(dev);
> > + pm_runtime_idle(dev);
> > +
> > + dev_info(dev, "ov02a10 probe --\n");
>
> Ditto.
>
Fixed in next release.
> > + return 0;
> > +
> > +err_clean_entity:
> > + media_entity_cleanup(&ov02a10->subdev.entity);
> > +err_power_off:
> > + __ov02a10_power_off(ov02a10);
> > +err_free_handler:
> > + v4l2_ctrl_handler_free(ov02a10->subdev.ctrl_handler);
> > +err_destroy_mutex:
> > + mutex_destroy(&ov02a10->mutex);
> > +
> > + return ret;
> > +}
> > +
> > +static int ov02a10_remove(struct i2c_client *client)
> > +{
> > + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> > + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > +
> > + v4l2_async_unregister_subdev(sd);
> > + media_entity_cleanup(&sd->entity);
> > + v4l2_ctrl_handler_free(sd->ctrl_handler);
> > + pm_runtime_disable(&client->dev);
> > + if (!pm_runtime_status_suspended(&client->dev))
> > + __ov02a10_power_off(ov02a10);
> > + pm_runtime_set_suspended(&client->dev);
> > + mutex_destroy(&ov02a10->mutex);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct of_device_id ov02a10_of_match[] = {
> > + { .compatible = "ovti,ov02a10" },
> > + {},
> > +};
> > +MODULE_DEVICE_TABLE(of, ov02a10_of_match);
> > +
> > +static struct i2c_driver ov02a10_i2c_driver = {
> > + .driver = {
> > + .name = "ov02a10",
> > + .pm = &ov02a10_pm_ops,
> > + .of_match_table = ov02a10_of_match,
> > + },
> > + .probe_new = &ov02a10_probe,
> > + .remove = &ov02a10_remove,
> > +};
> > +
> > +module_i2c_driver(ov02a10_i2c_driver);
> > +
> > +MODULE_AUTHOR("Dongchun Zhu <dongchun.zhu@mediatek.com>");
> > +MODULE_DESCRIPTION("OmniVision OV02A10 sensor driver");
> > +MODULE_LICENSE("GPL v2");
> > +
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2019-11-04 3:31 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-09-07 9:27 [V4, 0/2] media: i2c: Add support for OV02A10 sensor dongchun.zhu
2019-09-07 9:27 ` [V4, 1/2] media: dt-bindings: media: i2c: Add bindings for OV02A10 dongchun.zhu
2019-09-09 6:46 ` Sakari Ailus
2019-09-09 9:45 ` Andy Shevchenko
2019-09-09 9:57 ` Sakari Ailus
2019-09-09 10:11 ` Andy Shevchenko
2019-09-07 9:27 ` [V4, 2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver dongchun.zhu
2019-09-08 2:00 ` kbuild test robot
2019-09-08 2:31 ` kbuild test robot
2019-09-08 2:31 ` [PATCH] media: i2c: fix semicolon.cocci warnings kbuild test robot
2019-09-09 6:55 ` [V4, 2/2] media: i2c: Add Omnivision OV02A10 camera sensor driver Sakari Ailus
2019-11-04 3:30 ` Dongchun Zhu
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).