* [PATCH v2 00/21] Add new Marvell CN9130 SoC support
@ 2019-10-04 14:27 Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 01/21] arm64: dts: marvell: Enumerate the first AP806 syscon Miquel Raynal
` (21 more replies)
0 siblings, 22 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
Hello,
This is a respin of the last remaining patchset needed to fully support
Marvell CN9130 SoCs. The CN9130 is made of one AP807 and one internal
CP115. There are three development boards that are made of this SoC:
* CN9130-DB
* CN9131-DB (with one additional modular CP115 compared to CN9130-DB)
* CN9132-DB (with two additional modular CP115 compared to CN9130-DB)
This series applies on top of v5.4-rc1 and works thanks to the
previously merged following series:
* CP110 COMPHY:
https://patchwork.kernel.org/cover/11067647/
* AP806 CPU clocks:
https://patchwork.kernel.org/cover/11038577/
* AP807 clocks:
https://patchwork.kernel.org/cover/11076435/
* CP115 pinctrl:
http://patchwork.ozlabs.org/cover/1142107/
As CP110 and CP115 (alternatively, AP806 and AP807) are very similar,
we first reorganize DT files to create CP11x (and AP80x) generic
files, before including them from the new specific CP110/CP115
(AP806/AP807) ones.
A few small improvements/fixes in these files are also carried.
Thanks,
Miquèl
Changes since v1:
=================
* Rebased on top of v5.4-rc1.
* Rob's Reviewed-by tag on the first bindings patch (03).
* Used the AP_NAME macro instead of hardcoding ap806 in the DT which
turns generic (spotted by Gregory).
* Converted Marvell SoC compatible bindings to yaml (patch 16) as
requested by Rob. Add Gregory as the file maintainer.
Ben Peled (1):
dt-bindings: ap80x: replace AP806 with AP80x
Grzegorz Jaszczyk (7):
arm64: dts: marvell: Add AP806-dual cache description
arm64: dts: marvell: Add AP806-quad cache description
arm64: dts: marvell: Add AP807-quad cache description
dt-bindings: marvell: Declare the CN913x SoC compatibles
arm64: dts: marvell: Add support for Marvell CN9130-DB
arm64: dts: marvell: Add support for Marvell CN9131-DB
arm64: dts: marvell: Add support for Marvell CN9132-DB
Konstantin Porotchkin (1):
arm64: dts: marvell: Prepare the introduction of AP807 based SoCs
Miquel Raynal (12):
arm64: dts: marvell: Enumerate the first AP806 syscon
arm64: dts: marvell: Add AP806-dual missing CPU clocks
MAINTAINERS: Add new Marvell CN9130-based files to track
arm64: dts: marvell: Move clocks to AP806 specific file
arm64: dts: marvell: Add support for AP807/AP807-quad
arm64: dts: marvell: Fix CP110 NAND controller node multi-line comment
alignment
arm64: dts: marvell: Prepare the introduction of CP115
arm64: dts: marvell: Drop PCIe I/O ranges from CP11x file
arm64: dts: marvell: Externalize PCIe macros from CP11x file
arm64: dts: marvell: Add support for CP115
dt-bindings: marvell: Convert the SoC compatibles description to YAML
arm64: dts: marvell: Add support for Marvell CN9130 SoC support
...roller.txt => ap80x-system-controller.txt} | 14 +-
.../bindings/arm/marvell/armada-7k-8k.txt | 24 -
.../bindings/arm/marvell/armada-7k-8k.yaml | 61 ++
MAINTAINERS | 3 +-
arch/arm64/boot/dts/marvell/Makefile | 3 +
arch/arm64/boot/dts/marvell/armada-70x0.dtsi | 28 +-
.../boot/dts/marvell/armada-8040-mcbin.dtsi | 3 +-
arch/arm64/boot/dts/marvell/armada-80x0.dtsi | 56 +-
.../boot/dts/marvell/armada-ap806-dual.dtsi | 23 +
.../boot/dts/marvell/armada-ap806-quad.dtsi | 42 ++
arch/arm64/boot/dts/marvell/armada-ap806.dtsi | 456 +-------------
.../boot/dts/marvell/armada-ap807-quad.dtsi | 93 +++
arch/arm64/boot/dts/marvell/armada-ap807.dtsi | 29 +
arch/arm64/boot/dts/marvell/armada-ap80x.dtsi | 444 ++++++++++++++
.../arm64/boot/dts/marvell/armada-common.dtsi | 4 +-
arch/arm64/boot/dts/marvell/armada-cp110.dtsi | 575 +-----------------
arch/arm64/boot/dts/marvell/armada-cp115.dtsi | 12 +
arch/arm64/boot/dts/marvell/armada-cp11x.dtsi | 568 +++++++++++++++++
arch/arm64/boot/dts/marvell/cn9130-db.dts | 403 ++++++++++++
arch/arm64/boot/dts/marvell/cn9130.dtsi | 37 ++
arch/arm64/boot/dts/marvell/cn9131-db.dts | 202 ++++++
arch/arm64/boot/dts/marvell/cn9132-db.dts | 221 +++++++
22 files changed, 2210 insertions(+), 1091 deletions(-)
rename Documentation/devicetree/bindings/arm/marvell/{ap806-system-controller.txt => ap80x-system-controller.txt} (91%)
delete mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt
create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml
create mode 100644 arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi
create mode 100644 arch/arm64/boot/dts/marvell/armada-ap807.dtsi
create mode 100644 arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
create mode 100644 arch/arm64/boot/dts/marvell/armada-cp115.dtsi
create mode 100644 arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dts
create mode 100644 arch/arm64/boot/dts/marvell/cn9130.dtsi
create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dts
create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dts
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 25+ messages in thread
* [PATCH v2 01/21] arm64: dts: marvell: Enumerate the first AP806 syscon
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 02/21] arm64: dts: marvell: Add AP806-dual missing CPU clocks Miquel Raynal
` (20 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
There are two system controllers in the AP80x, like for ap_syscon1,
enumerate the first one by renaming it s/ap_syscon/ap_syscon0/.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
arch/arm64/boot/dts/marvell/armada-ap806.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
index d06dd198f2c7..a23ddd46efc5 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
@@ -246,7 +246,7 @@
status = "disabled";
};
- ap_syscon: system-controller@6f4000 {
+ ap_syscon0: system-controller@6f4000 {
compatible = "syscon", "simple-mfd";
reg = <0x6f4000 0x2000>;
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 02/21] arm64: dts: marvell: Add AP806-dual missing CPU clocks
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 01/21] arm64: dts: marvell: Enumerate the first AP806 syscon Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 03/21] dt-bindings: ap80x: replace AP806 with AP80x Miquel Raynal
` (19 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
CPU clocks have been added to AP806-quad but not to the -dual
variant.
Fixes: e043bbd61e01 ("arm64: dts: marvell: Add cpu clock node on Armada 7K/8K")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi
index 9024a2d9db07..62ae016ee6aa 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi
@@ -21,6 +21,7 @@
reg = <0x000>;
enable-method = "psci";
#cooling-cells = <2>;
+ clocks = <&cpu_clk 0>;
};
cpu1: cpu@1 {
device_type = "cpu";
@@ -28,6 +29,7 @@
reg = <0x001>;
enable-method = "psci";
#cooling-cells = <2>;
+ clocks = <&cpu_clk 0>;
};
};
};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 03/21] dt-bindings: ap80x: replace AP806 with AP80x
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 01/21] arm64: dts: marvell: Enumerate the first AP806 syscon Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 02/21] arm64: dts: marvell: Add AP806-dual missing CPU clocks Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 04/21] MAINTAINERS: Add new Marvell CN9130-based files to track Miquel Raynal
` (18 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Rob Herring, Antoine Tenart,
Grzegorz Jaszczyk, Gregory Clement, Maxime Chevallier,
Nadav Haklai, Thomas Petazzoni, Miquel Raynal, Stefan Chulski,
Marcin Wojtas, Ben Peled, linux-arm-kernel
From: Ben Peled <bpeled@marvell.com>
Rename the text file and update "AP806" into "AP806/AP807" where
relevant.
Signed-off-by: Ben Peled <bpeled@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
...-controller.txt => ap80x-system-controller.txt} | 14 +++++++-------
1 file changed, 7 insertions(+), 7 deletions(-)
rename Documentation/devicetree/bindings/arm/marvell/{ap806-system-controller.txt => ap80x-system-controller.txt} (91%)
diff --git a/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt b/Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt
similarity index 91%
rename from Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
rename to Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt
index 26410fbb85be..098d932fc963 100644
--- a/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
+++ b/Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt
@@ -1,15 +1,15 @@
-Marvell Armada AP806 System Controller
+Marvell Armada AP80x System Controller
======================================
-The AP806 is one of the two core HW blocks of the Marvell Armada 7K/8K
-SoCs. It contains system controllers, which provide several registers
-giving access to numerous features: clocks, pin-muxing and many other
-SoC configuration items. This DT binding allows to describe these
-system controllers.
+The AP806/AP807 is one of the two core HW blocks of the Marvell Armada
+7K/8K/931x SoCs. It contains system controllers, which provide several
+registers giving access to numerous features: clocks, pin-muxing and
+many other SoC configuration items. This DT binding allows to describe
+these system controllers.
For the top level node:
- compatible: must be: "syscon", "simple-mfd";
- - reg: register area of the AP806 system controller
+ - reg: register area of the AP80x system controller
SYSTEM CONTROLLER 0
===================
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 04/21] MAINTAINERS: Add new Marvell CN9130-based files to track
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (2 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 03/21] dt-bindings: ap80x: replace AP806 with AP80x Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 05/21] arm64: dts: marvell: Prepare the introduction of AP807 based SoCs Miquel Raynal
` (17 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
Marvell has a new branch of products called CN9130 based on AP807 and
CP115 which are derivatives of the currently supported AP806 and
CP110. Update the MAINTAINERS entry to reflect this change in the
naming.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
MAINTAINERS | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/MAINTAINERS b/MAINTAINERS
index 296de2b51c83..6b53cd42ae48 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1897,7 +1897,7 @@ F: arch/arm/boot/dts/dove*
F: arch/arm/boot/dts/orion5x*
T: git git://git.infradead.org/linux-mvebu.git
-ARM/Marvell Kirkwood and Armada 370, 375, 38x, 39x, XP, 3700, 7K/8K SOC support
+ARM/Marvell Kirkwood and Armada 370, 375, 38x, 39x, XP, 3700, 7K/8K, CN9130 SOC support
M: Jason Cooper <jason@lakedaemon.net>
M: Andrew Lunn <andrew@lunn.ch>
M: Gregory Clement <gregory.clement@bootlin.com>
@@ -1909,6 +1909,7 @@ F: arch/arm/boot/dts/kirkwood*
F: arch/arm/configs/mvebu_*_defconfig
F: arch/arm/mach-mvebu/
F: arch/arm64/boot/dts/marvell/armada*
+F: arch/arm64/boot/dts/marvell/cn913*
F: drivers/cpufreq/armada-37xx-cpufreq.c
F: drivers/cpufreq/armada-8k-cpufreq.c
F: drivers/cpufreq/mvebu-cpufreq.c
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 05/21] arm64: dts: marvell: Prepare the introduction of AP807 based SoCs
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (3 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 04/21] MAINTAINERS: Add new Marvell CN9130-based files to track Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 06/21] arm64: dts: marvell: Move clocks to AP806 specific file Miquel Raynal
` (16 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Konstantin Porotchkin,
Stefan Chulski, Marcin Wojtas, linux-arm-kernel
From: Konstantin Porotchkin <kostap@marvell.com>
Prepare the support for Marvell AP807 die. This die is very similar to
AP806 but uses different DDR PHY. AP807 is a major component of CN9130
SoC series.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
arch/arm64/boot/dts/marvell/armada-ap806.dtsi | 448 +----------------
arch/arm64/boot/dts/marvell/armada-ap80x.dtsi | 456 ++++++++++++++++++
2 files changed, 458 insertions(+), 446 deletions(-)
create mode 100644 arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
diff --git a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
index a23ddd46efc5..cdadb28f287e 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
@@ -5,454 +5,10 @@
* Device Tree file for Marvell Armada AP806.
*/
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/thermal/thermal.h>
-
-/dts-v1/;
+#define AP_NAME ap806
+#include "armada-ap80x.dtsi"
/ {
model = "Marvell Armada AP806";
compatible = "marvell,armada-ap806";
- #address-cells = <2>;
- #size-cells = <2>;
-
- aliases {
- serial0 = &uart0;
- serial1 = &uart1;
- gpio0 = &ap_gpio;
- spi0 = &spi0;
- };
-
- psci {
- compatible = "arm,psci-0.2";
- method = "smc";
- };
-
- reserved-memory {
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- /*
- * This area matches the mapping done with a
- * mainline U-Boot, and should be updated by the
- * bootloader.
- */
-
- psci-area@4000000 {
- reg = <0x0 0x4000000 0x0 0x200000>;
- no-map;
- };
- };
-
- ap806 {
- #address-cells = <2>;
- #size-cells = <2>;
- compatible = "simple-bus";
- interrupt-parent = <&gic>;
- ranges;
-
- config-space@f0000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "simple-bus";
- ranges = <0x0 0x0 0xf0000000 0x1000000>;
-
- gic: interrupt-controller@210000 {
- compatible = "arm,gic-400";
- #interrupt-cells = <3>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- interrupt-controller;
- interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- reg = <0x210000 0x10000>,
- <0x220000 0x20000>,
- <0x240000 0x20000>,
- <0x260000 0x20000>;
-
- gic_v2m0: v2m@280000 {
- compatible = "arm,gic-v2m-frame";
- msi-controller;
- reg = <0x280000 0x1000>;
- arm,msi-base-spi = <160>;
- arm,msi-num-spis = <32>;
- };
- gic_v2m1: v2m@290000 {
- compatible = "arm,gic-v2m-frame";
- msi-controller;
- reg = <0x290000 0x1000>;
- arm,msi-base-spi = <192>;
- arm,msi-num-spis = <32>;
- };
- gic_v2m2: v2m@2a0000 {
- compatible = "arm,gic-v2m-frame";
- msi-controller;
- reg = <0x2a0000 0x1000>;
- arm,msi-base-spi = <224>;
- arm,msi-num-spis = <32>;
- };
- gic_v2m3: v2m@2b0000 {
- compatible = "arm,gic-v2m-frame";
- msi-controller;
- reg = <0x2b0000 0x1000>;
- arm,msi-base-spi = <256>;
- arm,msi-num-spis = <32>;
- };
- };
-
- timer {
- compatible = "arm,armv8-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
-
- pmu {
- compatible = "arm,cortex-a72-pmu";
- interrupt-parent = <&pic>;
- interrupts = <17>;
- };
-
- odmi: odmi@300000 {
- compatible = "marvell,odmi-controller";
- interrupt-controller;
- msi-controller;
- marvell,odmi-frames = <4>;
- reg = <0x300000 0x4000>,
- <0x304000 0x4000>,
- <0x308000 0x4000>,
- <0x30C000 0x4000>;
- marvell,spi-base = <128>, <136>, <144>, <152>;
- };
-
- gicp: gicp@3f0040 {
- compatible = "marvell,ap806-gicp";
- reg = <0x3f0040 0x10>;
- marvell,spi-ranges = <64 64>, <288 64>;
- msi-controller;
- };
-
- pic: interrupt-controller@3f0100 {
- compatible = "marvell,armada-8k-pic";
- reg = <0x3f0100 0x10>;
- #interrupt-cells = <1>;
- interrupt-controller;
- interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- sei: interrupt-controller@3f0200 {
- compatible = "marvell,ap806-sei";
- reg = <0x3f0200 0x40>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
- #interrupt-cells = <1>;
- interrupt-controller;
- msi-controller;
- };
-
- xor@400000 {
- compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
- reg = <0x400000 0x1000>,
- <0x410000 0x1000>;
- msi-parent = <&gic_v2m0>;
- clocks = <&ap_clk 3>;
- dma-coherent;
- };
-
- xor@420000 {
- compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
- reg = <0x420000 0x1000>,
- <0x430000 0x1000>;
- msi-parent = <&gic_v2m0>;
- clocks = <&ap_clk 3>;
- dma-coherent;
- };
-
- xor@440000 {
- compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
- reg = <0x440000 0x1000>,
- <0x450000 0x1000>;
- msi-parent = <&gic_v2m0>;
- clocks = <&ap_clk 3>;
- dma-coherent;
- };
-
- xor@460000 {
- compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
- reg = <0x460000 0x1000>,
- <0x470000 0x1000>;
- msi-parent = <&gic_v2m0>;
- clocks = <&ap_clk 3>;
- dma-coherent;
- };
-
- spi0: spi@510600 {
- compatible = "marvell,armada-380-spi";
- reg = <0x510600 0x50>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ap_clk 3>;
- status = "disabled";
- };
-
- i2c0: i2c@511000 {
- compatible = "marvell,mv78230-i2c";
- reg = <0x511000 0x20>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
- timeout-ms = <1000>;
- clocks = <&ap_clk 3>;
- status = "disabled";
- };
-
- uart0: serial@512000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x512000 0x100>;
- reg-shift = <2>;
- interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
- reg-io-width = <1>;
- clocks = <&ap_clk 3>;
- status = "disabled";
- };
-
- uart1: serial@512100 {
- compatible = "snps,dw-apb-uart";
- reg = <0x512100 0x100>;
- reg-shift = <2>;
- interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
- reg-io-width = <1>;
- clocks = <&ap_clk 3>;
- status = "disabled";
-
- };
-
- watchdog: watchdog@610000 {
- compatible = "arm,sbsa-gwdt";
- reg = <0x610000 0x1000>, <0x600000 0x1000>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- ap_sdhci0: sdhci@6e0000 {
- compatible = "marvell,armada-ap806-sdhci";
- reg = <0x6e0000 0x300>;
- interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "core";
- clocks = <&ap_clk 4>;
- dma-coherent;
- marvell,xenon-phy-slow-mode;
- status = "disabled";
- };
-
- ap_syscon0: system-controller@6f4000 {
- compatible = "syscon", "simple-mfd";
- reg = <0x6f4000 0x2000>;
-
- ap_clk: clock {
- compatible = "marvell,ap806-clock";
- #clock-cells = <1>;
- };
-
- ap_pinctrl: pinctrl {
- compatible = "marvell,ap806-pinctrl";
-
- uart0_pins: uart0-pins {
- marvell,pins = "mpp11", "mpp19";
- marvell,function = "uart0";
- };
- };
-
- ap_gpio: gpio@1040 {
- compatible = "marvell,armada-8k-gpio";
- offset = <0x1040>;
- ngpios = <20>;
- gpio-controller;
- #gpio-cells = <2>;
- gpio-ranges = <&ap_pinctrl 0 0 20>;
- };
- };
-
- ap_syscon1: system-controller@6f8000 {
- compatible = "syscon", "simple-mfd";
- reg = <0x6f8000 0x1000>;
- #address-cells = <1>;
- #size-cells = <1>;
-
- cpu_clk: clock-cpu@278 {
- compatible = "marvell,ap806-cpu-clock";
- clocks = <&ap_clk 0>, <&ap_clk 1>;
- #clock-cells = <1>;
- reg = <0x278 0xa30>;
- };
-
- ap_thermal: thermal-sensor@80 {
- compatible = "marvell,armada-ap806-thermal";
- reg = <0x80 0x10>;
- interrupt-parent = <&sei>;
- interrupts = <18>;
- #thermal-sensor-cells = <1>;
- };
- };
- };
- };
-
- /*
- * The thermal IP features one internal sensor plus, if applicable, one
- * remote channel wired to one sensor per CPU.
- *
- * Only one thermal zone per AP/CP may trigger interrupts at a time, the
- * first one that will have a critical trip point will be chosen.
- */
- thermal-zones {
- ap_thermal_ic: ap-thermal-ic {
- polling-delay-passive = <0>; /* Interrupt driven */
- polling-delay = <0>; /* Interrupt driven */
-
- thermal-sensors = <&ap_thermal 0>;
-
- trips {
- ap_crit: ap-crit {
- temperature = <100000>; /* mC degrees */
- hysteresis = <2000>; /* mC degrees */
- type = "critical";
- };
- };
-
- cooling-maps { };
- };
-
- ap_thermal_cpu0: ap-thermal-cpu0 {
- polling-delay-passive = <1000>;
- polling-delay = <1000>;
-
- thermal-sensors = <&ap_thermal 1>;
-
- trips {
- cpu0_hot: cpu0-hot {
- temperature = <85000>;
- hysteresis = <2000>;
- type = "passive";
- };
- cpu0_emerg: cpu0-emerg {
- temperature = <95000>;
- hysteresis = <2000>;
- type = "passive";
- };
- };
-
- cooling-maps {
- map0_hot: map0-hot {
- trip = <&cpu0_hot>;
- cooling-device = <&cpu0 1 2>,
- <&cpu1 1 2>;
- };
- map0_emerg: map0-ermerg {
- trip = <&cpu0_emerg>;
- cooling-device = <&cpu0 3 3>,
- <&cpu1 3 3>;
- };
- };
- };
-
- ap_thermal_cpu1: ap-thermal-cpu1 {
- polling-delay-passive = <1000>;
- polling-delay = <1000>;
-
- thermal-sensors = <&ap_thermal 2>;
-
- trips {
- cpu1_hot: cpu1-hot {
- temperature = <85000>;
- hysteresis = <2000>;
- type = "passive";
- };
- cpu1_emerg: cpu1-emerg {
- temperature = <95000>;
- hysteresis = <2000>;
- type = "passive";
- };
- };
-
- cooling-maps {
- map1_hot: map1-hot {
- trip = <&cpu1_hot>;
- cooling-device = <&cpu0 1 2>,
- <&cpu1 1 2>;
- };
- map1_emerg: map1-emerg {
- trip = <&cpu1_emerg>;
- cooling-device = <&cpu0 3 3>,
- <&cpu1 3 3>;
- };
- };
- };
-
- ap_thermal_cpu2: ap-thermal-cpu2 {
- polling-delay-passive = <1000>;
- polling-delay = <1000>;
-
- thermal-sensors = <&ap_thermal 3>;
-
- trips {
- cpu2_hot: cpu2-hot {
- temperature = <85000>;
- hysteresis = <2000>;
- type = "passive";
- };
- cpu2_emerg: cpu2-emerg {
- temperature = <95000>;
- hysteresis = <2000>;
- type = "passive";
- };
- };
-
- cooling-maps {
- map2_hot: map2-hot {
- trip = <&cpu2_hot>;
- cooling-device = <&cpu2 1 2>,
- <&cpu3 1 2>;
- };
- map2_emerg: map2-emerg {
- trip = <&cpu2_emerg>;
- cooling-device = <&cpu2 3 3>,
- <&cpu3 3 3>;
- };
- };
- };
-
- ap_thermal_cpu3: ap-thermal-cpu3 {
- polling-delay-passive = <1000>;
- polling-delay = <1000>;
-
- thermal-sensors = <&ap_thermal 4>;
-
- trips {
- cpu3_hot: cpu3-hot {
- temperature = <85000>;
- hysteresis = <2000>;
- type = "passive";
- };
- cpu3_emerg: cpu3-emerg {
- temperature = <95000>;
- hysteresis = <2000>;
- type = "passive";
- };
- };
-
- cooling-maps {
- map3_hot: map3-bhot {
- trip = <&cpu3_hot>;
- cooling-device = <&cpu2 1 2>,
- <&cpu3 1 2>;
- };
- map3_emerg: map3-emerg {
- trip = <&cpu3_emerg>;
- cooling-device = <&cpu2 3 3>,
- <&cpu3 3 3>;
- };
- };
- };
- };
};
diff --git a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
new file mode 100644
index 000000000000..0dc1365e5758
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
@@ -0,0 +1,456 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marvell Technology Group Ltd.
+ *
+ * Device Tree file for Marvell Armada AP80x.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/dts-v1/;
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ gpio0 = &ap_gpio;
+ spi0 = &spi0;
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /*
+ * This area matches the mapping done with a
+ * mainline U-Boot, and should be updated by the
+ * bootloader.
+ */
+
+ psci-area@4000000 {
+ reg = <0x0 0x4000000 0x0 0x200000>;
+ no-map;
+ };
+ };
+
+ AP_NAME {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ interrupt-parent = <&gic>;
+ ranges;
+
+ config-space@f0000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0x0 0x0 0xf0000000 0x1000000>;
+
+ gic: interrupt-controller@210000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ reg = <0x210000 0x10000>,
+ <0x220000 0x20000>,
+ <0x240000 0x20000>,
+ <0x260000 0x20000>;
+
+ gic_v2m0: v2m@280000 {
+ compatible = "arm,gic-v2m-frame";
+ msi-controller;
+ reg = <0x280000 0x1000>;
+ arm,msi-base-spi = <160>;
+ arm,msi-num-spis = <32>;
+ };
+ gic_v2m1: v2m@290000 {
+ compatible = "arm,gic-v2m-frame";
+ msi-controller;
+ reg = <0x290000 0x1000>;
+ arm,msi-base-spi = <192>;
+ arm,msi-num-spis = <32>;
+ };
+ gic_v2m2: v2m@2a0000 {
+ compatible = "arm,gic-v2m-frame";
+ msi-controller;
+ reg = <0x2a0000 0x1000>;
+ arm,msi-base-spi = <224>;
+ arm,msi-num-spis = <32>;
+ };
+ gic_v2m3: v2m@2b0000 {
+ compatible = "arm,gic-v2m-frame";
+ msi-controller;
+ reg = <0x2b0000 0x1000>;
+ arm,msi-base-spi = <256>;
+ arm,msi-num-spis = <32>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a72-pmu";
+ interrupt-parent = <&pic>;
+ interrupts = <17>;
+ };
+
+ odmi: odmi@300000 {
+ compatible = "marvell,odmi-controller";
+ interrupt-controller;
+ msi-controller;
+ marvell,odmi-frames = <4>;
+ reg = <0x300000 0x4000>,
+ <0x304000 0x4000>,
+ <0x308000 0x4000>,
+ <0x30C000 0x4000>;
+ marvell,spi-base = <128>, <136>, <144>, <152>;
+ };
+
+ gicp: gicp@3f0040 {
+ compatible = "marvell,ap806-gicp";
+ reg = <0x3f0040 0x10>;
+ marvell,spi-ranges = <64 64>, <288 64>;
+ msi-controller;
+ };
+
+ pic: interrupt-controller@3f0100 {
+ compatible = "marvell,armada-8k-pic";
+ reg = <0x3f0100 0x10>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ sei: interrupt-controller@3f0200 {
+ compatible = "marvell,ap806-sei";
+ reg = <0x3f0200 0x40>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ msi-controller;
+ };
+
+ xor@400000 {
+ compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+ reg = <0x400000 0x1000>,
+ <0x410000 0x1000>;
+ msi-parent = <&gic_v2m0>;
+ clocks = <&ap_clk 3>;
+ dma-coherent;
+ };
+
+ xor@420000 {
+ compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+ reg = <0x420000 0x1000>,
+ <0x430000 0x1000>;
+ msi-parent = <&gic_v2m0>;
+ clocks = <&ap_clk 3>;
+ dma-coherent;
+ };
+
+ xor@440000 {
+ compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+ reg = <0x440000 0x1000>,
+ <0x450000 0x1000>;
+ msi-parent = <&gic_v2m0>;
+ clocks = <&ap_clk 3>;
+ dma-coherent;
+ };
+
+ xor@460000 {
+ compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+ reg = <0x460000 0x1000>,
+ <0x470000 0x1000>;
+ msi-parent = <&gic_v2m0>;
+ clocks = <&ap_clk 3>;
+ dma-coherent;
+ };
+
+ spi0: spi@510600 {
+ compatible = "marvell,armada-380-spi";
+ reg = <0x510600 0x50>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ap_clk 3>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@511000 {
+ compatible = "marvell,mv78230-i2c";
+ reg = <0x511000 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ timeout-ms = <1000>;
+ clocks = <&ap_clk 3>;
+ status = "disabled";
+ };
+
+ uart0: serial@512000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x512000 0x100>;
+ reg-shift = <2>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ reg-io-width = <1>;
+ clocks = <&ap_clk 3>;
+ status = "disabled";
+ };
+
+ uart1: serial@512100 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x512100 0x100>;
+ reg-shift = <2>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ reg-io-width = <1>;
+ clocks = <&ap_clk 3>;
+ status = "disabled";
+
+ };
+
+ watchdog: watchdog@610000 {
+ compatible = "arm,sbsa-gwdt";
+ reg = <0x610000 0x1000>, <0x600000 0x1000>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ ap_sdhci0: sdhci@6e0000 {
+ compatible = "marvell,armada-ap806-sdhci";
+ reg = <0x6e0000 0x300>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "core";
+ clocks = <&ap_clk 4>;
+ dma-coherent;
+ marvell,xenon-phy-slow-mode;
+ status = "disabled";
+ };
+
+ ap_syscon0: system-controller@6f4000 {
+ compatible = "syscon", "simple-mfd";
+ reg = <0x6f4000 0x2000>;
+
+ ap_clk: clock {
+ compatible = "marvell,ap806-clock";
+ #clock-cells = <1>;
+ };
+
+ ap_pinctrl: pinctrl {
+ compatible = "marvell,ap806-pinctrl";
+
+ uart0_pins: uart0-pins {
+ marvell,pins = "mpp11", "mpp19";
+ marvell,function = "uart0";
+ };
+ };
+
+ ap_gpio: gpio@1040 {
+ compatible = "marvell,armada-8k-gpio";
+ offset = <0x1040>;
+ ngpios = <20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&ap_pinctrl 0 0 20>;
+ };
+ };
+
+ ap_syscon1: system-controller@6f8000 {
+ compatible = "syscon", "simple-mfd";
+ reg = <0x6f8000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpu_clk: clock-cpu@278 {
+ compatible = "marvell,ap806-cpu-clock";
+ clocks = <&ap_clk 0>, <&ap_clk 1>;
+ #clock-cells = <1>;
+ reg = <0x278 0xa30>;
+ };
+
+ ap_thermal: thermal-sensor@80 {
+ compatible = "marvell,armada-ap806-thermal";
+ reg = <0x80 0x10>;
+ interrupt-parent = <&sei>;
+ interrupts = <18>;
+ #thermal-sensor-cells = <1>;
+ };
+ };
+ };
+ };
+
+ /*
+ * The thermal IP features one internal sensor plus, if applicable, one
+ * remote channel wired to one sensor per CPU.
+ *
+ * Only one thermal zone per AP/CP may trigger interrupts at a time, the
+ * first one that will have a critical trip point will be chosen.
+ */
+ thermal-zones {
+ ap_thermal_ic: ap-thermal-ic {
+ polling-delay-passive = <0>; /* Interrupt driven */
+ polling-delay = <0>; /* Interrupt driven */
+
+ thermal-sensors = <&ap_thermal 0>;
+
+ trips {
+ ap_crit: ap-crit {
+ temperature = <100000>; /* mC degrees */
+ hysteresis = <2000>; /* mC degrees */
+ type = "critical";
+ };
+ };
+
+ cooling-maps { };
+ };
+
+ ap_thermal_cpu0: ap-thermal-cpu0 {
+ polling-delay-passive = <1000>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&ap_thermal 1>;
+
+ trips {
+ cpu0_hot: cpu0-hot {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu0_emerg: cpu0-emerg {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ };
+
+ cooling-maps {
+ map0_hot: map0-hot {
+ trip = <&cpu0_hot>;
+ cooling-device = <&cpu0 1 2>,
+ <&cpu1 1 2>;
+ };
+ map0_emerg: map0-ermerg {
+ trip = <&cpu0_emerg>;
+ cooling-device = <&cpu0 3 3>,
+ <&cpu1 3 3>;
+ };
+ };
+ };
+
+ ap_thermal_cpu1: ap-thermal-cpu1 {
+ polling-delay-passive = <1000>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&ap_thermal 2>;
+
+ trips {
+ cpu1_hot: cpu1-hot {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu1_emerg: cpu1-emerg {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ };
+
+ cooling-maps {
+ map1_hot: map1-hot {
+ trip = <&cpu1_hot>;
+ cooling-device = <&cpu0 1 2>,
+ <&cpu1 1 2>;
+ };
+ map1_emerg: map1-emerg {
+ trip = <&cpu1_emerg>;
+ cooling-device = <&cpu0 3 3>,
+ <&cpu1 3 3>;
+ };
+ };
+ };
+
+ ap_thermal_cpu2: ap-thermal-cpu2 {
+ polling-delay-passive = <1000>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&ap_thermal 3>;
+
+ trips {
+ cpu2_hot: cpu2-hot {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu2_emerg: cpu2-emerg {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ };
+
+ cooling-maps {
+ map2_hot: map2-hot {
+ trip = <&cpu2_hot>;
+ cooling-device = <&cpu2 1 2>,
+ <&cpu3 1 2>;
+ };
+ map2_emerg: map2-emerg {
+ trip = <&cpu2_emerg>;
+ cooling-device = <&cpu2 3 3>,
+ <&cpu3 3 3>;
+ };
+ };
+ };
+
+ ap_thermal_cpu3: ap-thermal-cpu3 {
+ polling-delay-passive = <1000>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&ap_thermal 4>;
+
+ trips {
+ cpu3_hot: cpu3-hot {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu3_emerg: cpu3-emerg {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ };
+
+ cooling-maps {
+ map3_hot: map3-bhot {
+ trip = <&cpu3_hot>;
+ cooling-device = <&cpu2 1 2>,
+ <&cpu3 1 2>;
+ };
+ map3_emerg: map3-emerg {
+ trip = <&cpu3_emerg>;
+ cooling-device = <&cpu2 3 3>,
+ <&cpu3 3 3>;
+ };
+ };
+ };
+ };
+};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 06/21] arm64: dts: marvell: Move clocks to AP806 specific file
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (4 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 05/21] arm64: dts: marvell: Prepare the introduction of AP807 based SoCs Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 07/21] arm64: dts: marvell: Add support for AP807/AP807-quad Miquel Raynal
` (15 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
Regular clocks and CPU clocks are specific to AP806, move them out of
the generic AP80x file so that AP807 can use its own clocks.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
arch/arm64/boot/dts/marvell/armada-ap806.dtsi | 16 ++++++++++++++++
arch/arm64/boot/dts/marvell/armada-ap80x.dtsi | 12 ------------
2 files changed, 16 insertions(+), 12 deletions(-)
diff --git a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
index cdadb28f287e..866628679ac7 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
@@ -12,3 +12,19 @@
model = "Marvell Armada AP806";
compatible = "marvell,armada-ap806";
};
+
+&ap_syscon0 {
+ ap_clk: clock {
+ compatible = "marvell,ap806-clock";
+ #clock-cells = <1>;
+ };
+};
+
+&ap_syscon1 {
+ cpu_clk: clock-cpu@278 {
+ compatible = "marvell,ap806-cpu-clock";
+ clocks = <&ap_clk 0>, <&ap_clk 1>;
+ #clock-cells = <1>;
+ reg = <0x278 0xa30>;
+ };
+};
diff --git a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
index 0dc1365e5758..e7438c21ccee 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
@@ -248,11 +248,6 @@
compatible = "syscon", "simple-mfd";
reg = <0x6f4000 0x2000>;
- ap_clk: clock {
- compatible = "marvell,ap806-clock";
- #clock-cells = <1>;
- };
-
ap_pinctrl: pinctrl {
compatible = "marvell,ap806-pinctrl";
@@ -278,13 +273,6 @@
#address-cells = <1>;
#size-cells = <1>;
- cpu_clk: clock-cpu@278 {
- compatible = "marvell,ap806-cpu-clock";
- clocks = <&ap_clk 0>, <&ap_clk 1>;
- #clock-cells = <1>;
- reg = <0x278 0xa30>;
- };
-
ap_thermal: thermal-sensor@80 {
compatible = "marvell,armada-ap806-thermal";
reg = <0x80 0x10>;
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 07/21] arm64: dts: marvell: Add support for AP807/AP807-quad
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (5 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 06/21] arm64: dts: marvell: Move clocks to AP806 specific file Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 08/21] arm64: dts: marvell: Add AP806-dual cache description Miquel Raynal
` (14 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
Describe AP807 and AP807-quad support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
.../boot/dts/marvell/armada-ap807-quad.dtsi | 51 +++++++++++++++++++
arch/arm64/boot/dts/marvell/armada-ap807.dtsi | 29 +++++++++++
2 files changed, 80 insertions(+)
create mode 100644 arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi
create mode 100644 arch/arm64/boot/dts/marvell/armada-ap807.dtsi
diff --git a/arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi b/arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi
new file mode 100644
index 000000000000..65364691257d
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for Marvell Armada AP807 Quad
+ *
+ * Copyright (C) 2019 Marvell Technology Group Ltd.
+ */
+
+#include "armada-ap807.dtsi"
+
+/ {
+ model = "Marvell Armada AP807 Quad";
+ compatible = "marvell,armada-ap807-quad", "marvell,armada-ap807";
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72", "arm,armv8";
+ reg = <0x000>;
+ enable-method = "psci";
+ #cooling-cells = <2>;
+ clocks = <&cpu_clk 0>;
+ };
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72", "arm,armv8";
+ reg = <0x001>;
+ enable-method = "psci";
+ #cooling-cells = <2>;
+ clocks = <&cpu_clk 0>;
+ };
+ cpu2: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72", "arm,armv8";
+ reg = <0x100>;
+ enable-method = "psci";
+ #cooling-cells = <2>;
+ clocks = <&cpu_clk 1>;
+ };
+ cpu3: cpu@101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72", "arm,armv8";
+ reg = <0x101>;
+ enable-method = "psci";
+ #cooling-cells = <2>;
+ clocks = <&cpu_clk 1>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/marvell/armada-ap807.dtsi b/arch/arm64/boot/dts/marvell/armada-ap807.dtsi
new file mode 100644
index 000000000000..623010f3ca89
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-ap807.dtsi
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for Marvell Armada AP807
+ *
+ * Copyright (C) 2019 Marvell Technology Group Ltd.
+ */
+
+#define AP_NAME ap807
+#include "armada-ap80x.dtsi"
+
+/ {
+ model = "Marvell Armada AP807";
+ compatible = "marvell,armada-ap807";
+};
+
+&ap_syscon0 {
+ ap_clk: clock {
+ compatible = "marvell,ap807-clock";
+ #clock-cells = <1>;
+ };
+};
+
+&ap_syscon1 {
+ cpu_clk: clock-cpu {
+ compatible = "marvell,ap807-cpu-clock";
+ clocks = <&ap_clk 0>, <&ap_clk 1>;
+ #clock-cells = <1>;
+ };
+};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 08/21] arm64: dts: marvell: Add AP806-dual cache description
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (6 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 07/21] arm64: dts: marvell: Add support for AP807/AP807-quad Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 09/21] arm64: dts: marvell: Add AP806-quad " Miquel Raynal
` (13 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
From: Grzegorz Jaszczyk <jaz@semihalf.com>
Adding appropriate entries to device-tree allows the cache description
to show up in sysfs under: /sys/devices/system/cpu/cpuX/cache/.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
.../boot/dts/marvell/armada-ap806-dual.dtsi | 21 +++++++++++++++++++
1 file changed, 21 insertions(+)
diff --git a/arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi
index 62ae016ee6aa..09849558a776 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap806-dual.dtsi
@@ -22,6 +22,13 @@
enable-method = "psci";
#cooling-cells = <2>;
clocks = <&cpu_clk 0>;
+ i-cache-size = <0xc000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2>;
};
cpu1: cpu@1 {
device_type = "cpu";
@@ -30,6 +37,20 @@
enable-method = "psci";
#cooling-cells = <2>;
clocks = <&cpu_clk 0>;
+ i-cache-size = <0xc000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2>;
+ };
+
+ l2: l2-cache {
+ compatible = "cache";
+ cache-size = <0x80000>;
+ cache-line-size = <64>;
+ cache-sets = <512>;
};
};
};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 09/21] arm64: dts: marvell: Add AP806-quad cache description
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (7 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 08/21] arm64: dts: marvell: Add AP806-dual cache description Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 10/21] arm64: dts: marvell: Add AP807-quad " Miquel Raynal
` (12 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
From: Grzegorz Jaszczyk <jaz@semihalf.com>
Adding appropriate entries to device-tree allows the cache description
to show up in sysfs under: /sys/devices/system/cpu/cpuX/cache/.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
.../boot/dts/marvell/armada-ap806-quad.dtsi | 42 +++++++++++++++++++
1 file changed, 42 insertions(+)
diff --git a/arch/arm64/boot/dts/marvell/armada-ap806-quad.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806-quad.dtsi
index c25bc65727b5..3db427122f9e 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap806-quad.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap806-quad.dtsi
@@ -22,6 +22,13 @@
enable-method = "psci";
#cooling-cells = <2>;
clocks = <&cpu_clk 0>;
+ i-cache-size = <0xc000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2_0>;
};
cpu1: cpu@1 {
device_type = "cpu";
@@ -30,6 +37,13 @@
enable-method = "psci";
#cooling-cells = <2>;
clocks = <&cpu_clk 0>;
+ i-cache-size = <0xc000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2_0>;
};
cpu2: cpu@100 {
device_type = "cpu";
@@ -38,6 +52,13 @@
enable-method = "psci";
#cooling-cells = <2>;
clocks = <&cpu_clk 1>;
+ i-cache-size = <0xc000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2_1>;
};
cpu3: cpu@101 {
device_type = "cpu";
@@ -46,6 +67,27 @@
enable-method = "psci";
#cooling-cells = <2>;
clocks = <&cpu_clk 1>;
+ i-cache-size = <0xc000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2_1>;
+ };
+
+ l2_0: l2-cache0 {
+ compatible = "cache";
+ cache-size = <0x80000>;
+ cache-line-size = <64>;
+ cache-sets = <512>;
+ };
+
+ l2_1: l2-cache1 {
+ compatible = "cache";
+ cache-size = <0x80000>;
+ cache-line-size = <64>;
+ cache-sets = <512>;
};
};
};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 10/21] arm64: dts: marvell: Add AP807-quad cache description
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (8 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 09/21] arm64: dts: marvell: Add AP806-quad " Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 11/21] arm64: dts: marvell: Fix CP110 NAND controller node multi-line comment alignment Miquel Raynal
` (11 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
From: Grzegorz Jaszczyk <jaz@semihalf.com>
Adding appropriate entries to device-tree allows the cache description
to show up in sysfs under: /sys/devices/system/cpu/cpuX/cache/.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
.../boot/dts/marvell/armada-ap807-quad.dtsi | 42 +++++++++++++++++++
1 file changed, 42 insertions(+)
diff --git a/arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi b/arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi
index 65364691257d..840466e143b4 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi
@@ -22,6 +22,13 @@
enable-method = "psci";
#cooling-cells = <2>;
clocks = <&cpu_clk 0>;
+ i-cache-size = <0xc000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2_0>;
};
cpu1: cpu@1 {
device_type = "cpu";
@@ -30,6 +37,13 @@
enable-method = "psci";
#cooling-cells = <2>;
clocks = <&cpu_clk 0>;
+ i-cache-size = <0xc000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2_0>;
};
cpu2: cpu@100 {
device_type = "cpu";
@@ -38,6 +52,13 @@
enable-method = "psci";
#cooling-cells = <2>;
clocks = <&cpu_clk 1>;
+ i-cache-size = <0xc000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2_1>;
};
cpu3: cpu@101 {
device_type = "cpu";
@@ -46,6 +67,27 @@
enable-method = "psci";
#cooling-cells = <2>;
clocks = <&cpu_clk 1>;
+ i-cache-size = <0xc000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2_1>;
+ };
+
+ l2_0: l2-cache0 {
+ compatible = "cache";
+ cache-size = <0x80000>;
+ cache-line-size = <64>;
+ cache-sets = <512>;
+ };
+
+ l2_1: l2-cache1 {
+ compatible = "cache";
+ cache-size = <0x80000>;
+ cache-line-size = <64>;
+ cache-sets = <512>;
};
};
};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 11/21] arm64: dts: marvell: Fix CP110 NAND controller node multi-line comment alignment
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (9 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 10/21] arm64: dts: marvell: Add AP807-quad " Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 12/21] arm64: dts: marvell: Prepare the introduction of CP115 Miquel Raynal
` (10 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
Fix this tiny typo before renaming/changing this file.
Fixes: 72a3713fadfd ("arm64: dts: marvell: de-duplicate CP110 description")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
arch/arm64/boot/dts/marvell/armada-cp110.dtsi | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
index d81944902650..8259fc8f86f2 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
@@ -438,10 +438,10 @@
CP110_LABEL(nand_controller): nand@720000 {
/*
- * Due to the limitation of the pins available
- * this controller is only usable on the CPM
- * for A7K and on the CPS for A8K.
- */
+ * Due to the limitation of the pins available
+ * this controller is only usable on the CPM
+ * for A7K and on the CPS for A8K.
+ */
compatible = "marvell,armada-8k-nand-controller",
"marvell,armada370-nand-controller";
reg = <0x720000 0x54>;
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 12/21] arm64: dts: marvell: Prepare the introduction of CP115
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (10 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 11/21] arm64: dts: marvell: Fix CP110 NAND controller node multi-line comment alignment Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 13/21] arm64: dts: marvell: Drop PCIe I/O ranges from CP11x file Miquel Raynal
` (9 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
CP110 and CP115 are almost the same in terms of features and have a
very limited set of differences. Let's create an armada-cp11x.dtsi
file which will be used to instantiate both CP110 and CP115
nodes.
The only changes between the two armada-cp11{0,x}.dtsi files are the
following naming in macros: s/CP110/CP11X/.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
arch/arm64/boot/dts/marvell/armada-70x0.dtsi | 28 +-
arch/arm64/boot/dts/marvell/armada-80x0.dtsi | 56 +-
.../arm64/boot/dts/marvell/armada-common.dtsi | 4 +-
arch/arm64/boot/dts/marvell/armada-cp110.dtsi | 575 +----------------
arch/arm64/boot/dts/marvell/armada-cp11x.dtsi | 579 ++++++++++++++++++
5 files changed, 627 insertions(+), 615 deletions(-)
create mode 100644 arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
diff --git a/arch/arm64/boot/dts/marvell/armada-70x0.dtsi b/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
index e5c6d7c25819..4e78ccd207b7 100644
--- a/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
@@ -17,23 +17,23 @@
/*
* Instantiate the CP110
*/
-#define CP110_NAME cp0
-#define CP110_BASE f2000000
-#define CP110_PCIE_IO_BASE 0xf9000000
-#define CP110_PCIE_MEM_BASE 0xf6000000
-#define CP110_PCIE0_BASE f2600000
-#define CP110_PCIE1_BASE f2620000
-#define CP110_PCIE2_BASE f2640000
+#define CP11X_NAME cp0
+#define CP11X_BASE f2000000
+#define CP11X_PCIE_IO_BASE 0xf9000000
+#define CP11X_PCIE_MEM_BASE 0xf6000000
+#define CP11X_PCIE0_BASE f2600000
+#define CP11X_PCIE1_BASE f2620000
+#define CP11X_PCIE2_BASE f2640000
#include "armada-cp110.dtsi"
-#undef CP110_NAME
-#undef CP110_BASE
-#undef CP110_PCIE_IO_BASE
-#undef CP110_PCIE_MEM_BASE
-#undef CP110_PCIE0_BASE
-#undef CP110_PCIE1_BASE
-#undef CP110_PCIE2_BASE
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIE_IO_BASE
+#undef CP11X_PCIE_MEM_BASE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
&cp0_gpio1 {
status = "okay";
diff --git a/arch/arm64/boot/dts/marvell/armada-80x0.dtsi b/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
index 8129b40f12a4..ebb98836ec9c 100644
--- a/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
@@ -19,44 +19,44 @@
/*
* Instantiate the master CP110
*/
-#define CP110_NAME cp0
-#define CP110_BASE f2000000
-#define CP110_PCIE_IO_BASE 0xf9000000
-#define CP110_PCIE_MEM_BASE 0xf6000000
-#define CP110_PCIE0_BASE f2600000
-#define CP110_PCIE1_BASE f2620000
-#define CP110_PCIE2_BASE f2640000
+#define CP11X_NAME cp0
+#define CP11X_BASE f2000000
+#define CP11X_PCIE_IO_BASE 0xf9000000
+#define CP11X_PCIE_MEM_BASE 0xf6000000
+#define CP11X_PCIE0_BASE f2600000
+#define CP11X_PCIE1_BASE f2620000
+#define CP11X_PCIE2_BASE f2640000
#include "armada-cp110.dtsi"
-#undef CP110_NAME
-#undef CP110_BASE
-#undef CP110_PCIE_IO_BASE
-#undef CP110_PCIE_MEM_BASE
-#undef CP110_PCIE0_BASE
-#undef CP110_PCIE1_BASE
-#undef CP110_PCIE2_BASE
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIE_IO_BASE
+#undef CP11X_PCIE_MEM_BASE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
/*
* Instantiate the slave CP110
*/
-#define CP110_NAME cp1
-#define CP110_BASE f4000000
-#define CP110_PCIE_IO_BASE 0xfd000000
-#define CP110_PCIE_MEM_BASE 0xfa000000
-#define CP110_PCIE0_BASE f4600000
-#define CP110_PCIE1_BASE f4620000
-#define CP110_PCIE2_BASE f4640000
+#define CP11X_NAME cp1
+#define CP11X_BASE f4000000
+#define CP11X_PCIE_IO_BASE 0xfd000000
+#define CP11X_PCIE_MEM_BASE 0xfa000000
+#define CP11X_PCIE0_BASE f4600000
+#define CP11X_PCIE1_BASE f4620000
+#define CP11X_PCIE2_BASE f4640000
#include "armada-cp110.dtsi"
-#undef CP110_NAME
-#undef CP110_BASE
-#undef CP110_PCIE_IO_BASE
-#undef CP110_PCIE_MEM_BASE
-#undef CP110_PCIE0_BASE
-#undef CP110_PCIE1_BASE
-#undef CP110_PCIE2_BASE
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIE_IO_BASE
+#undef CP11X_PCIE_MEM_BASE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
/* The 80x0 has two CP blocks, but uses only one block from each. */
&cp1_gpio1 {
diff --git a/arch/arm64/boot/dts/marvell/armada-common.dtsi b/arch/arm64/boot/dts/marvell/armada-common.dtsi
index b29c6405d214..c04c6c475022 100644
--- a/arch/arm64/boot/dts/marvell/armada-common.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-common.dtsi
@@ -6,6 +6,6 @@
/* Common definitions used by Armada 7K/8K DTs */
#define PASTER(x, y) x ## y
#define EVALUATOR(x, y) PASTER(x, y)
-#define CP110_LABEL(name) EVALUATOR(CP110_NAME, EVALUATOR(_, name))
-#define CP110_NODE_NAME(name) EVALUATOR(CP110_NAME, EVALUATOR(-, name))
+#define CP11X_LABEL(name) EVALUATOR(CP11X_NAME, EVALUATOR(_, name))
+#define CP11X_NODE_NAME(name) EVALUATOR(CP11X_NAME, EVALUATOR(-, name))
#define ADDRESSIFY(addr) EVALUATOR(0x, addr)
diff --git a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
index 8259fc8f86f2..4fd33b0fa56e 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
@@ -1,579 +1,12 @@
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
- * Copyright (C) 2016 Marvell Technology Group Ltd.
+ * Copyright (C) 2019 Marvell Technology Group Ltd.
*
* Device Tree file for Marvell Armada CP110.
*/
-#include <dt-bindings/interrupt-controller/mvebu-icu.h>
-#include <dt-bindings/thermal/thermal.h>
+#define CP11X_TYPE cp110
-#include "armada-common.dtsi"
+#include "armada-cp11x.dtsi"
-#define CP110_PCIEx_IO_BASE(iface) (CP110_PCIE_IO_BASE + (iface * 0x10000))
-#define CP110_PCIEx_MEM_BASE(iface) (CP110_PCIE_MEM_BASE + (iface * 0x1000000))
-#define CP110_PCIEx_CONF_BASE(iface) (CP110_PCIEx_MEM_BASE(iface) + 0xf00000)
-
-/ {
- /*
- * The contents of the node are defined below, in order to
- * save one indentation level
- */
- CP110_NAME: CP110_NAME { };
-
- /*
- * CPs only have one sensor in the thermal IC.
- *
- * The cooling maps are empty as there are no cooling devices.
- */
- thermal-zones {
- CP110_LABEL(thermal_ic): CP110_NODE_NAME(thermal-ic) {
- polling-delay-passive = <0>; /* Interrupt driven */
- polling-delay = <0>; /* Interrupt driven */
-
- thermal-sensors = <&CP110_LABEL(thermal) 0>;
-
- trips {
- CP110_LABEL(crit): crit {
- temperature = <100000>; /* mC degrees */
- hysteresis = <2000>; /* mC degrees */
- type = "critical";
- };
- };
-
- cooling-maps { };
- };
- };
-};
-
-&CP110_NAME {
- #address-cells = <2>;
- #size-cells = <2>;
- compatible = "simple-bus";
- interrupt-parent = <&CP110_LABEL(icu_nsr)>;
- ranges;
-
- config-space@CP110_BASE {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "simple-bus";
- ranges = <0x0 0x0 ADDRESSIFY(CP110_BASE) 0x2000000>;
-
- CP110_LABEL(ethernet): ethernet@0 {
- compatible = "marvell,armada-7k-pp22";
- reg = <0x0 0x100000>, <0x129000 0xb000>;
- clocks = <&CP110_LABEL(clk) 1 3>, <&CP110_LABEL(clk) 1 9>,
- <&CP110_LABEL(clk) 1 5>, <&CP110_LABEL(clk) 1 6>,
- <&CP110_LABEL(clk) 1 18>;
- clock-names = "pp_clk", "gop_clk",
- "mg_clk", "mg_core_clk", "axi_clk";
- marvell,system-controller = <&CP110_LABEL(syscon0)>;
- status = "disabled";
- dma-coherent;
-
- CP110_LABEL(eth0): eth0 {
- interrupts = <39 IRQ_TYPE_LEVEL_HIGH>,
- <43 IRQ_TYPE_LEVEL_HIGH>,
- <47 IRQ_TYPE_LEVEL_HIGH>,
- <51 IRQ_TYPE_LEVEL_HIGH>,
- <55 IRQ_TYPE_LEVEL_HIGH>,
- <59 IRQ_TYPE_LEVEL_HIGH>,
- <63 IRQ_TYPE_LEVEL_HIGH>,
- <67 IRQ_TYPE_LEVEL_HIGH>,
- <71 IRQ_TYPE_LEVEL_HIGH>,
- <129 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "hif0", "hif1", "hif2",
- "hif3", "hif4", "hif5", "hif6", "hif7",
- "hif8", "link";
- port-id = <0>;
- gop-port-id = <0>;
- status = "disabled";
- };
-
- CP110_LABEL(eth1): eth1 {
- interrupts = <40 IRQ_TYPE_LEVEL_HIGH>,
- <44 IRQ_TYPE_LEVEL_HIGH>,
- <48 IRQ_TYPE_LEVEL_HIGH>,
- <52 IRQ_TYPE_LEVEL_HIGH>,
- <56 IRQ_TYPE_LEVEL_HIGH>,
- <60 IRQ_TYPE_LEVEL_HIGH>,
- <64 IRQ_TYPE_LEVEL_HIGH>,
- <68 IRQ_TYPE_LEVEL_HIGH>,
- <72 IRQ_TYPE_LEVEL_HIGH>,
- <128 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "hif0", "hif1", "hif2",
- "hif3", "hif4", "hif5", "hif6", "hif7",
- "hif8", "link";
- port-id = <1>;
- gop-port-id = <2>;
- status = "disabled";
- };
-
- CP110_LABEL(eth2): eth2 {
- interrupts = <41 IRQ_TYPE_LEVEL_HIGH>,
- <45 IRQ_TYPE_LEVEL_HIGH>,
- <49 IRQ_TYPE_LEVEL_HIGH>,
- <53 IRQ_TYPE_LEVEL_HIGH>,
- <57 IRQ_TYPE_LEVEL_HIGH>,
- <61 IRQ_TYPE_LEVEL_HIGH>,
- <65 IRQ_TYPE_LEVEL_HIGH>,
- <69 IRQ_TYPE_LEVEL_HIGH>,
- <73 IRQ_TYPE_LEVEL_HIGH>,
- <127 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "hif0", "hif1", "hif2",
- "hif3", "hif4", "hif5", "hif6", "hif7",
- "hif8", "link";
- port-id = <2>;
- gop-port-id = <3>;
- status = "disabled";
- };
- };
-
- CP110_LABEL(comphy): phy@120000 {
- compatible = "marvell,comphy-cp110";
- reg = <0x120000 0x6000>;
- marvell,system-controller = <&CP110_LABEL(syscon0)>;
- clocks = <&CP110_LABEL(clk) 1 5>, <&CP110_LABEL(clk) 1 6>,
- <&CP110_LABEL(clk) 1 18>;
- clock-names = "mg_clk", "mg_core_clk", "axi_clk";
- #address-cells = <1>;
- #size-cells = <0>;
-
- CP110_LABEL(comphy0): phy@0 {
- reg = <0>;
- #phy-cells = <1>;
- };
-
- CP110_LABEL(comphy1): phy@1 {
- reg = <1>;
- #phy-cells = <1>;
- };
-
- CP110_LABEL(comphy2): phy@2 {
- reg = <2>;
- #phy-cells = <1>;
- };
-
- CP110_LABEL(comphy3): phy@3 {
- reg = <3>;
- #phy-cells = <1>;
- };
-
- CP110_LABEL(comphy4): phy@4 {
- reg = <4>;
- #phy-cells = <1>;
- };
-
- CP110_LABEL(comphy5): phy@5 {
- reg = <5>;
- #phy-cells = <1>;
- };
- };
-
- CP110_LABEL(mdio): mdio@12a200 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "marvell,orion-mdio";
- reg = <0x12a200 0x10>;
- clocks = <&CP110_LABEL(clk) 1 9>, <&CP110_LABEL(clk) 1 5>,
- <&CP110_LABEL(clk) 1 6>, <&CP110_LABEL(clk) 1 18>;
- status = "disabled";
- };
-
- CP110_LABEL(xmdio): mdio@12a600 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "marvell,xmdio";
- reg = <0x12a600 0x10>;
- clocks = <&CP110_LABEL(clk) 1 5>,
- <&CP110_LABEL(clk) 1 6>, <&CP110_LABEL(clk) 1 18>;
- status = "disabled";
- };
-
- CP110_LABEL(icu): interrupt-controller@1e0000 {
- compatible = "marvell,cp110-icu";
- reg = <0x1e0000 0x440>;
- #address-cells = <1>;
- #size-cells = <1>;
-
- CP110_LABEL(icu_nsr): interrupt-controller@10 {
- compatible = "marvell,cp110-icu-nsr";
- reg = <0x10 0x20>;
- #interrupt-cells = <2>;
- interrupt-controller;
- msi-parent = <&gicp>;
- };
-
- CP110_LABEL(icu_sei): interrupt-controller@50 {
- compatible = "marvell,cp110-icu-sei";
- reg = <0x50 0x10>;
- #interrupt-cells = <2>;
- interrupt-controller;
- msi-parent = <&sei>;
- };
- };
-
- CP110_LABEL(rtc): rtc@284000 {
- compatible = "marvell,armada-8k-rtc";
- reg = <0x284000 0x20>, <0x284080 0x24>;
- reg-names = "rtc", "rtc-soc";
- interrupts = <77 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- CP110_LABEL(syscon0): system-controller@440000 {
- compatible = "syscon", "simple-mfd";
- reg = <0x440000 0x2000>;
-
- CP110_LABEL(clk): clock {
- compatible = "marvell,cp110-clock";
- #clock-cells = <2>;
- };
-
- CP110_LABEL(gpio1): gpio@100 {
- compatible = "marvell,armada-8k-gpio";
- offset = <0x100>;
- ngpios = <32>;
- gpio-controller;
- #gpio-cells = <2>;
- gpio-ranges = <&CP110_LABEL(pinctrl) 0 0 32>;
- interrupt-controller;
- interrupts = <86 IRQ_TYPE_LEVEL_HIGH>,
- <85 IRQ_TYPE_LEVEL_HIGH>,
- <84 IRQ_TYPE_LEVEL_HIGH>,
- <83 IRQ_TYPE_LEVEL_HIGH>;
- #interrupt-cells = <2>;
- status = "disabled";
- };
-
- CP110_LABEL(gpio2): gpio@140 {
- compatible = "marvell,armada-8k-gpio";
- offset = <0x140>;
- ngpios = <31>;
- gpio-controller;
- #gpio-cells = <2>;
- gpio-ranges = <&CP110_LABEL(pinctrl) 0 32 31>;
- interrupt-controller;
- interrupts = <82 IRQ_TYPE_LEVEL_HIGH>,
- <81 IRQ_TYPE_LEVEL_HIGH>,
- <80 IRQ_TYPE_LEVEL_HIGH>,
- <79 IRQ_TYPE_LEVEL_HIGH>;
- #interrupt-cells = <2>;
- status = "disabled";
- };
- };
-
- CP110_LABEL(syscon1): system-controller@400000 {
- compatible = "syscon", "simple-mfd";
- reg = <0x400000 0x1000>;
- #address-cells = <1>;
- #size-cells = <1>;
-
- CP110_LABEL(thermal): thermal-sensor@70 {
- compatible = "marvell,armada-cp110-thermal";
- reg = <0x70 0x10>;
- interrupts-extended =
- <&CP110_LABEL(icu_sei) 116 IRQ_TYPE_LEVEL_HIGH>;
- #thermal-sensor-cells = <1>;
- };
- };
-
- CP110_LABEL(usb3_0): usb3@500000 {
- compatible = "marvell,armada-8k-xhci",
- "generic-xhci";
- reg = <0x500000 0x4000>;
- dma-coherent;
- interrupts = <106 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "core", "reg";
- clocks = <&CP110_LABEL(clk) 1 22>,
- <&CP110_LABEL(clk) 1 16>;
- status = "disabled";
- };
-
- CP110_LABEL(usb3_1): usb3@510000 {
- compatible = "marvell,armada-8k-xhci",
- "generic-xhci";
- reg = <0x510000 0x4000>;
- dma-coherent;
- interrupts = <105 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "core", "reg";
- clocks = <&CP110_LABEL(clk) 1 23>,
- <&CP110_LABEL(clk) 1 16>;
- status = "disabled";
- };
-
- CP110_LABEL(sata0): sata@540000 {
- compatible = "marvell,armada-8k-ahci",
- "generic-ahci";
- reg = <0x540000 0x30000>;
- dma-coherent;
- interrupts = <107 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&CP110_LABEL(clk) 1 15>,
- <&CP110_LABEL(clk) 1 16>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "disabled";
-
- sata-port@0 {
- reg = <0>;
- };
-
- sata-port@1 {
- reg = <1>;
- };
- };
-
- CP110_LABEL(xor0): xor@6a0000 {
- compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
- reg = <0x6a0000 0x1000>, <0x6b0000 0x1000>;
- dma-coherent;
- msi-parent = <&gic_v2m0>;
- clock-names = "core", "reg";
- clocks = <&CP110_LABEL(clk) 1 8>,
- <&CP110_LABEL(clk) 1 14>;
- };
-
- CP110_LABEL(xor1): xor@6c0000 {
- compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
- reg = <0x6c0000 0x1000>, <0x6d0000 0x1000>;
- dma-coherent;
- msi-parent = <&gic_v2m0>;
- clock-names = "core", "reg";
- clocks = <&CP110_LABEL(clk) 1 7>,
- <&CP110_LABEL(clk) 1 14>;
- };
-
- CP110_LABEL(spi0): spi@700600 {
- compatible = "marvell,armada-380-spi";
- reg = <0x700600 0x50>;
- #address-cells = <0x1>;
- #size-cells = <0x0>;
- clock-names = "core", "axi";
- clocks = <&CP110_LABEL(clk) 1 21>,
- <&CP110_LABEL(clk) 1 17>;
- status = "disabled";
- };
-
- CP110_LABEL(spi1): spi@700680 {
- compatible = "marvell,armada-380-spi";
- reg = <0x700680 0x50>;
- #address-cells = <1>;
- #size-cells = <0>;
- clock-names = "core", "axi";
- clocks = <&CP110_LABEL(clk) 1 21>,
- <&CP110_LABEL(clk) 1 17>;
- status = "disabled";
- };
-
- CP110_LABEL(i2c0): i2c@701000 {
- compatible = "marvell,mv78230-i2c";
- reg = <0x701000 0x20>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <120 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "core", "reg";
- clocks = <&CP110_LABEL(clk) 1 21>,
- <&CP110_LABEL(clk) 1 17>;
- status = "disabled";
- };
-
- CP110_LABEL(i2c1): i2c@701100 {
- compatible = "marvell,mv78230-i2c";
- reg = <0x701100 0x20>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <121 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "core", "reg";
- clocks = <&CP110_LABEL(clk) 1 21>,
- <&CP110_LABEL(clk) 1 17>;
- status = "disabled";
- };
-
- CP110_LABEL(uart0): serial@702000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x702000 0x100>;
- reg-shift = <2>;
- interrupts = <122 IRQ_TYPE_LEVEL_HIGH>;
- reg-io-width = <1>;
- clock-names = "baudclk", "apb_pclk";
- clocks = <&CP110_LABEL(clk) 1 21>,
- <&CP110_LABEL(clk) 1 17>;
- status = "disabled";
- };
-
- CP110_LABEL(uart1): serial@702100 {
- compatible = "snps,dw-apb-uart";
- reg = <0x702100 0x100>;
- reg-shift = <2>;
- interrupts = <123 IRQ_TYPE_LEVEL_HIGH>;
- reg-io-width = <1>;
- clock-names = "baudclk", "apb_pclk";
- clocks = <&CP110_LABEL(clk) 1 21>,
- <&CP110_LABEL(clk) 1 17>;
- status = "disabled";
- };
-
- CP110_LABEL(uart2): serial@702200 {
- compatible = "snps,dw-apb-uart";
- reg = <0x702200 0x100>;
- reg-shift = <2>;
- interrupts = <124 IRQ_TYPE_LEVEL_HIGH>;
- reg-io-width = <1>;
- clock-names = "baudclk", "apb_pclk";
- clocks = <&CP110_LABEL(clk) 1 21>,
- <&CP110_LABEL(clk) 1 17>;
- status = "disabled";
- };
-
- CP110_LABEL(uart3): serial@702300 {
- compatible = "snps,dw-apb-uart";
- reg = <0x702300 0x100>;
- reg-shift = <2>;
- interrupts = <125 IRQ_TYPE_LEVEL_HIGH>;
- reg-io-width = <1>;
- clock-names = "baudclk", "apb_pclk";
- clocks = <&CP110_LABEL(clk) 1 21>,
- <&CP110_LABEL(clk) 1 17>;
- status = "disabled";
- };
-
- CP110_LABEL(nand_controller): nand@720000 {
- /*
- * Due to the limitation of the pins available
- * this controller is only usable on the CPM
- * for A7K and on the CPS for A8K.
- */
- compatible = "marvell,armada-8k-nand-controller",
- "marvell,armada370-nand-controller";
- reg = <0x720000 0x54>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <115 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "core", "reg";
- clocks = <&CP110_LABEL(clk) 1 2>,
- <&CP110_LABEL(clk) 1 17>;
- marvell,system-controller = <&CP110_LABEL(syscon0)>;
- status = "disabled";
- };
-
- CP110_LABEL(trng): trng@760000 {
- compatible = "marvell,armada-8k-rng",
- "inside-secure,safexcel-eip76";
- reg = <0x760000 0x7d>;
- interrupts = <95 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "core", "reg";
- clocks = <&CP110_LABEL(clk) 1 25>,
- <&CP110_LABEL(clk) 1 17>;
- status = "okay";
- };
-
- CP110_LABEL(sdhci0): sdhci@780000 {
- compatible = "marvell,armada-cp110-sdhci";
- reg = <0x780000 0x300>;
- interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;
- clock-names = "core", "axi";
- clocks = <&CP110_LABEL(clk) 1 4>, <&CP110_LABEL(clk) 1 18>;
- dma-coherent;
- status = "disabled";
- };
-
- CP110_LABEL(crypto): crypto@800000 {
- compatible = "inside-secure,safexcel-eip197b";
- reg = <0x800000 0x200000>;
- interrupts = <87 IRQ_TYPE_LEVEL_HIGH>,
- <88 IRQ_TYPE_LEVEL_HIGH>,
- <89 IRQ_TYPE_LEVEL_HIGH>,
- <90 IRQ_TYPE_LEVEL_HIGH>,
- <91 IRQ_TYPE_LEVEL_HIGH>,
- <92 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "mem", "ring0", "ring1",
- "ring2", "ring3", "eip";
- clock-names = "core", "reg";
- clocks = <&CP110_LABEL(clk) 1 26>,
- <&CP110_LABEL(clk) 1 17>;
- dma-coherent;
- };
- };
-
- CP110_LABEL(pcie0): pcie@CP110_PCIE0_BASE {
- compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
- reg = <0 ADDRESSIFY(CP110_PCIE0_BASE) 0 0x10000>,
- <0 CP110_PCIEx_CONF_BASE(0) 0 0x80000>;
- reg-names = "ctrl", "config";
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- device_type = "pci";
- dma-coherent;
- msi-parent = <&gic_v2m0>;
-
- bus-range = <0 0xff>;
- ranges =
- /* downstream I/O */
- <0x81000000 0 CP110_PCIEx_IO_BASE(0) 0 CP110_PCIEx_IO_BASE(0) 0 0x10000
- /* non-prefetchable memory */
- 0x82000000 0 CP110_PCIEx_MEM_BASE(0) 0 CP110_PCIEx_MEM_BASE(0) 0 0xf00000>;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &CP110_LABEL(icu_nsr) 22 IRQ_TYPE_LEVEL_HIGH>;
- interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
- num-lanes = <1>;
- clock-names = "core", "reg";
- clocks = <&CP110_LABEL(clk) 1 13>, <&CP110_LABEL(clk) 1 14>;
- status = "disabled";
- };
-
- CP110_LABEL(pcie1): pcie@CP110_PCIE1_BASE {
- compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
- reg = <0 ADDRESSIFY(CP110_PCIE1_BASE) 0 0x10000>,
- <0 CP110_PCIEx_CONF_BASE(1) 0 0x80000>;
- reg-names = "ctrl", "config";
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- device_type = "pci";
- dma-coherent;
- msi-parent = <&gic_v2m0>;
-
- bus-range = <0 0xff>;
- ranges =
- /* downstream I/O */
- <0x81000000 0 CP110_PCIEx_IO_BASE(1) 0 CP110_PCIEx_IO_BASE(1) 0 0x10000
- /* non-prefetchable memory */
- 0x82000000 0 CP110_PCIEx_MEM_BASE(1) 0 CP110_PCIEx_MEM_BASE(1) 0 0xf00000>;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &CP110_LABEL(icu_nsr) 24 IRQ_TYPE_LEVEL_HIGH>;
- interrupts = <24 IRQ_TYPE_LEVEL_HIGH>;
-
- num-lanes = <1>;
- clock-names = "core", "reg";
- clocks = <&CP110_LABEL(clk) 1 11>, <&CP110_LABEL(clk) 1 14>;
- status = "disabled";
- };
-
- CP110_LABEL(pcie2): pcie@CP110_PCIE2_BASE {
- compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
- reg = <0 ADDRESSIFY(CP110_PCIE2_BASE) 0 0x10000>,
- <0 CP110_PCIEx_CONF_BASE(2) 0 0x80000>;
- reg-names = "ctrl", "config";
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- device_type = "pci";
- dma-coherent;
- msi-parent = <&gic_v2m0>;
-
- bus-range = <0 0xff>;
- ranges =
- /* downstream I/O */
- <0x81000000 0 CP110_PCIEx_IO_BASE(2) 0 CP110_PCIEx_IO_BASE(2) 0 0x10000
- /* non-prefetchable memory */
- 0x82000000 0 CP110_PCIEx_MEM_BASE(2) 0 CP110_PCIEx_MEM_BASE(2) 0 0xf00000>;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &CP110_LABEL(icu_nsr) 23 IRQ_TYPE_LEVEL_HIGH>;
- interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
-
- num-lanes = <1>;
- clock-names = "core", "reg";
- clocks = <&CP110_LABEL(clk) 1 12>, <&CP110_LABEL(clk) 1 14>;
- status = "disabled";
- };
-};
+#undef CP11X_TYPE
diff --git a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
new file mode 100644
index 000000000000..3e77cf34604c
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
@@ -0,0 +1,579 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2016 Marvell Technology Group Ltd.
+ *
+ * Device Tree file for Marvell Armada CP11x.
+ */
+
+#include <dt-bindings/interrupt-controller/mvebu-icu.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "armada-common.dtsi"
+
+#define CP11X_PCIEx_IO_BASE(iface) (CP11X_PCIE_IO_BASE + (iface * 0x10000))
+#define CP11X_PCIEx_MEM_BASE(iface) (CP11X_PCIE_MEM_BASE + (iface * 0x1000000))
+#define CP11X_PCIEx_CONF_BASE(iface) (CP11X_PCIEx_MEM_BASE(iface) + 0xf00000)
+
+/ {
+ /*
+ * The contents of the node are defined below, in order to
+ * save one indentation level
+ */
+ CP11X_NAME: CP11X_NAME { };
+
+ /*
+ * CPs only have one sensor in the thermal IC.
+ *
+ * The cooling maps are empty as there are no cooling devices.
+ */
+ thermal-zones {
+ CP11X_LABEL(thermal_ic): CP11X_NODE_NAME(thermal-ic) {
+ polling-delay-passive = <0>; /* Interrupt driven */
+ polling-delay = <0>; /* Interrupt driven */
+
+ thermal-sensors = <&CP11X_LABEL(thermal) 0>;
+
+ trips {
+ CP11X_LABEL(crit): crit {
+ temperature = <100000>; /* mC degrees */
+ hysteresis = <2000>; /* mC degrees */
+ type = "critical";
+ };
+ };
+
+ cooling-maps { };
+ };
+ };
+};
+
+&CP11X_NAME {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ interrupt-parent = <&CP11X_LABEL(icu_nsr)>;
+ ranges;
+
+ config-space@CP11X_BASE {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0x0 0x0 ADDRESSIFY(CP11X_BASE) 0x2000000>;
+
+ CP11X_LABEL(ethernet): ethernet@0 {
+ compatible = "marvell,armada-7k-pp22";
+ reg = <0x0 0x100000>, <0x129000 0xb000>;
+ clocks = <&CP11X_LABEL(clk) 1 3>, <&CP11X_LABEL(clk) 1 9>,
+ <&CP11X_LABEL(clk) 1 5>, <&CP11X_LABEL(clk) 1 6>,
+ <&CP11X_LABEL(clk) 1 18>;
+ clock-names = "pp_clk", "gop_clk",
+ "mg_clk", "mg_core_clk", "axi_clk";
+ marvell,system-controller = <&CP11X_LABEL(syscon0)>;
+ status = "disabled";
+ dma-coherent;
+
+ CP11X_LABEL(eth0): eth0 {
+ interrupts = <39 IRQ_TYPE_LEVEL_HIGH>,
+ <43 IRQ_TYPE_LEVEL_HIGH>,
+ <47 IRQ_TYPE_LEVEL_HIGH>,
+ <51 IRQ_TYPE_LEVEL_HIGH>,
+ <55 IRQ_TYPE_LEVEL_HIGH>,
+ <59 IRQ_TYPE_LEVEL_HIGH>,
+ <63 IRQ_TYPE_LEVEL_HIGH>,
+ <67 IRQ_TYPE_LEVEL_HIGH>,
+ <71 IRQ_TYPE_LEVEL_HIGH>,
+ <129 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hif0", "hif1", "hif2",
+ "hif3", "hif4", "hif5", "hif6", "hif7",
+ "hif8", "link";
+ port-id = <0>;
+ gop-port-id = <0>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(eth1): eth1 {
+ interrupts = <40 IRQ_TYPE_LEVEL_HIGH>,
+ <44 IRQ_TYPE_LEVEL_HIGH>,
+ <48 IRQ_TYPE_LEVEL_HIGH>,
+ <52 IRQ_TYPE_LEVEL_HIGH>,
+ <56 IRQ_TYPE_LEVEL_HIGH>,
+ <60 IRQ_TYPE_LEVEL_HIGH>,
+ <64 IRQ_TYPE_LEVEL_HIGH>,
+ <68 IRQ_TYPE_LEVEL_HIGH>,
+ <72 IRQ_TYPE_LEVEL_HIGH>,
+ <128 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hif0", "hif1", "hif2",
+ "hif3", "hif4", "hif5", "hif6", "hif7",
+ "hif8", "link";
+ port-id = <1>;
+ gop-port-id = <2>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(eth2): eth2 {
+ interrupts = <41 IRQ_TYPE_LEVEL_HIGH>,
+ <45 IRQ_TYPE_LEVEL_HIGH>,
+ <49 IRQ_TYPE_LEVEL_HIGH>,
+ <53 IRQ_TYPE_LEVEL_HIGH>,
+ <57 IRQ_TYPE_LEVEL_HIGH>,
+ <61 IRQ_TYPE_LEVEL_HIGH>,
+ <65 IRQ_TYPE_LEVEL_HIGH>,
+ <69 IRQ_TYPE_LEVEL_HIGH>,
+ <73 IRQ_TYPE_LEVEL_HIGH>,
+ <127 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hif0", "hif1", "hif2",
+ "hif3", "hif4", "hif5", "hif6", "hif7",
+ "hif8", "link";
+ port-id = <2>;
+ gop-port-id = <3>;
+ status = "disabled";
+ };
+ };
+
+ CP11X_LABEL(comphy): phy@120000 {
+ compatible = "marvell,comphy-cp110";
+ reg = <0x120000 0x6000>;
+ marvell,system-controller = <&CP11X_LABEL(syscon0)>;
+ clocks = <&CP11X_LABEL(clk) 1 5>, <&CP11X_LABEL(clk) 1 6>,
+ <&CP11X_LABEL(clk) 1 18>;
+ clock-names = "mg_clk", "mg_core_clk", "axi_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ CP11X_LABEL(comphy0): phy@0 {
+ reg = <0>;
+ #phy-cells = <1>;
+ };
+
+ CP11X_LABEL(comphy1): phy@1 {
+ reg = <1>;
+ #phy-cells = <1>;
+ };
+
+ CP11X_LABEL(comphy2): phy@2 {
+ reg = <2>;
+ #phy-cells = <1>;
+ };
+
+ CP11X_LABEL(comphy3): phy@3 {
+ reg = <3>;
+ #phy-cells = <1>;
+ };
+
+ CP11X_LABEL(comphy4): phy@4 {
+ reg = <4>;
+ #phy-cells = <1>;
+ };
+
+ CP11X_LABEL(comphy5): phy@5 {
+ reg = <5>;
+ #phy-cells = <1>;
+ };
+ };
+
+ CP11X_LABEL(mdio): mdio@12a200 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "marvell,orion-mdio";
+ reg = <0x12a200 0x10>;
+ clocks = <&CP11X_LABEL(clk) 1 9>, <&CP11X_LABEL(clk) 1 5>,
+ <&CP11X_LABEL(clk) 1 6>, <&CP11X_LABEL(clk) 1 18>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(xmdio): mdio@12a600 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "marvell,xmdio";
+ reg = <0x12a600 0x10>;
+ clocks = <&CP11X_LABEL(clk) 1 5>,
+ <&CP11X_LABEL(clk) 1 6>, <&CP11X_LABEL(clk) 1 18>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(icu): interrupt-controller@1e0000 {
+ compatible = "marvell,cp110-icu";
+ reg = <0x1e0000 0x440>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ CP11X_LABEL(icu_nsr): interrupt-controller@10 {
+ compatible = "marvell,cp110-icu-nsr";
+ reg = <0x10 0x20>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ msi-parent = <&gicp>;
+ };
+
+ CP11X_LABEL(icu_sei): interrupt-controller@50 {
+ compatible = "marvell,cp110-icu-sei";
+ reg = <0x50 0x10>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ msi-parent = <&sei>;
+ };
+ };
+
+ CP11X_LABEL(rtc): rtc@284000 {
+ compatible = "marvell,armada-8k-rtc";
+ reg = <0x284000 0x20>, <0x284080 0x24>;
+ reg-names = "rtc", "rtc-soc";
+ interrupts = <77 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ CP11X_LABEL(syscon0): system-controller@440000 {
+ compatible = "syscon", "simple-mfd";
+ reg = <0x440000 0x2000>;
+
+ CP11X_LABEL(clk): clock {
+ compatible = "marvell,cp110-clock";
+ #clock-cells = <2>;
+ };
+
+ CP11X_LABEL(gpio1): gpio@100 {
+ compatible = "marvell,armada-8k-gpio";
+ offset = <0x100>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&CP11X_LABEL(pinctrl) 0 0 32>;
+ interrupt-controller;
+ interrupts = <86 IRQ_TYPE_LEVEL_HIGH>,
+ <85 IRQ_TYPE_LEVEL_HIGH>,
+ <84 IRQ_TYPE_LEVEL_HIGH>,
+ <83 IRQ_TYPE_LEVEL_HIGH>;
+ #interrupt-cells = <2>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(gpio2): gpio@140 {
+ compatible = "marvell,armada-8k-gpio";
+ offset = <0x140>;
+ ngpios = <31>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&CP11X_LABEL(pinctrl) 0 32 31>;
+ interrupt-controller;
+ interrupts = <82 IRQ_TYPE_LEVEL_HIGH>,
+ <81 IRQ_TYPE_LEVEL_HIGH>,
+ <80 IRQ_TYPE_LEVEL_HIGH>,
+ <79 IRQ_TYPE_LEVEL_HIGH>;
+ #interrupt-cells = <2>;
+ status = "disabled";
+ };
+ };
+
+ CP11X_LABEL(syscon1): system-controller@400000 {
+ compatible = "syscon", "simple-mfd";
+ reg = <0x400000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ CP11X_LABEL(thermal): thermal-sensor@70 {
+ compatible = "marvell,armada-cp110-thermal";
+ reg = <0x70 0x10>;
+ interrupts-extended =
+ <&CP11X_LABEL(icu_sei) 116 IRQ_TYPE_LEVEL_HIGH>;
+ #thermal-sensor-cells = <1>;
+ };
+ };
+
+ CP11X_LABEL(usb3_0): usb3@500000 {
+ compatible = "marvell,armada-8k-xhci",
+ "generic-xhci";
+ reg = <0x500000 0x4000>;
+ dma-coherent;
+ interrupts = <106 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "core", "reg";
+ clocks = <&CP11X_LABEL(clk) 1 22>,
+ <&CP11X_LABEL(clk) 1 16>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(usb3_1): usb3@510000 {
+ compatible = "marvell,armada-8k-xhci",
+ "generic-xhci";
+ reg = <0x510000 0x4000>;
+ dma-coherent;
+ interrupts = <105 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "core", "reg";
+ clocks = <&CP11X_LABEL(clk) 1 23>,
+ <&CP11X_LABEL(clk) 1 16>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(sata0): sata@540000 {
+ compatible = "marvell,armada-8k-ahci",
+ "generic-ahci";
+ reg = <0x540000 0x30000>;
+ dma-coherent;
+ interrupts = <107 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&CP11X_LABEL(clk) 1 15>,
+ <&CP11X_LABEL(clk) 1 16>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ sata-port@0 {
+ reg = <0>;
+ };
+
+ sata-port@1 {
+ reg = <1>;
+ };
+ };
+
+ CP11X_LABEL(xor0): xor@6a0000 {
+ compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+ reg = <0x6a0000 0x1000>, <0x6b0000 0x1000>;
+ dma-coherent;
+ msi-parent = <&gic_v2m0>;
+ clock-names = "core", "reg";
+ clocks = <&CP11X_LABEL(clk) 1 8>,
+ <&CP11X_LABEL(clk) 1 14>;
+ };
+
+ CP11X_LABEL(xor1): xor@6c0000 {
+ compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+ reg = <0x6c0000 0x1000>, <0x6d0000 0x1000>;
+ dma-coherent;
+ msi-parent = <&gic_v2m0>;
+ clock-names = "core", "reg";
+ clocks = <&CP11X_LABEL(clk) 1 7>,
+ <&CP11X_LABEL(clk) 1 14>;
+ };
+
+ CP11X_LABEL(spi0): spi@700600 {
+ compatible = "marvell,armada-380-spi";
+ reg = <0x700600 0x50>;
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ clock-names = "core", "axi";
+ clocks = <&CP11X_LABEL(clk) 1 21>,
+ <&CP11X_LABEL(clk) 1 17>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(spi1): spi@700680 {
+ compatible = "marvell,armada-380-spi";
+ reg = <0x700680 0x50>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "core", "axi";
+ clocks = <&CP11X_LABEL(clk) 1 21>,
+ <&CP11X_LABEL(clk) 1 17>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(i2c0): i2c@701000 {
+ compatible = "marvell,mv78230-i2c";
+ reg = <0x701000 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <120 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "core", "reg";
+ clocks = <&CP11X_LABEL(clk) 1 21>,
+ <&CP11X_LABEL(clk) 1 17>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(i2c1): i2c@701100 {
+ compatible = "marvell,mv78230-i2c";
+ reg = <0x701100 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <121 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "core", "reg";
+ clocks = <&CP11X_LABEL(clk) 1 21>,
+ <&CP11X_LABEL(clk) 1 17>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(uart0): serial@702000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x702000 0x100>;
+ reg-shift = <2>;
+ interrupts = <122 IRQ_TYPE_LEVEL_HIGH>;
+ reg-io-width = <1>;
+ clock-names = "baudclk", "apb_pclk";
+ clocks = <&CP11X_LABEL(clk) 1 21>,
+ <&CP11X_LABEL(clk) 1 17>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(uart1): serial@702100 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x702100 0x100>;
+ reg-shift = <2>;
+ interrupts = <123 IRQ_TYPE_LEVEL_HIGH>;
+ reg-io-width = <1>;
+ clock-names = "baudclk", "apb_pclk";
+ clocks = <&CP11X_LABEL(clk) 1 21>,
+ <&CP11X_LABEL(clk) 1 17>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(uart2): serial@702200 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x702200 0x100>;
+ reg-shift = <2>;
+ interrupts = <124 IRQ_TYPE_LEVEL_HIGH>;
+ reg-io-width = <1>;
+ clock-names = "baudclk", "apb_pclk";
+ clocks = <&CP11X_LABEL(clk) 1 21>,
+ <&CP11X_LABEL(clk) 1 17>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(uart3): serial@702300 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x702300 0x100>;
+ reg-shift = <2>;
+ interrupts = <125 IRQ_TYPE_LEVEL_HIGH>;
+ reg-io-width = <1>;
+ clock-names = "baudclk", "apb_pclk";
+ clocks = <&CP11X_LABEL(clk) 1 21>,
+ <&CP11X_LABEL(clk) 1 17>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(nand_controller): nand@720000 {
+ /*
+ * Due to the limitation of the pins available
+ * this controller is only usable on the CPM
+ * for A7K and on the CPS for A8K.
+ */
+ compatible = "marvell,armada-8k-nand-controller",
+ "marvell,armada370-nand-controller";
+ reg = <0x720000 0x54>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <115 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "core", "reg";
+ clocks = <&CP11X_LABEL(clk) 1 2>,
+ <&CP11X_LABEL(clk) 1 17>;
+ marvell,system-controller = <&CP11X_LABEL(syscon0)>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(trng): trng@760000 {
+ compatible = "marvell,armada-8k-rng",
+ "inside-secure,safexcel-eip76";
+ reg = <0x760000 0x7d>;
+ interrupts = <95 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "core", "reg";
+ clocks = <&CP11X_LABEL(clk) 1 25>,
+ <&CP11X_LABEL(clk) 1 17>;
+ status = "okay";
+ };
+
+ CP11X_LABEL(sdhci0): sdhci@780000 {
+ compatible = "marvell,armada-cp110-sdhci";
+ reg = <0x780000 0x300>;
+ interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "core", "axi";
+ clocks = <&CP11X_LABEL(clk) 1 4>, <&CP11X_LABEL(clk) 1 18>;
+ dma-coherent;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(crypto): crypto@800000 {
+ compatible = "inside-secure,safexcel-eip197b";
+ reg = <0x800000 0x200000>;
+ interrupts = <87 IRQ_TYPE_LEVEL_HIGH>,
+ <88 IRQ_TYPE_LEVEL_HIGH>,
+ <89 IRQ_TYPE_LEVEL_HIGH>,
+ <90 IRQ_TYPE_LEVEL_HIGH>,
+ <91 IRQ_TYPE_LEVEL_HIGH>,
+ <92 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "mem", "ring0", "ring1",
+ "ring2", "ring3", "eip";
+ clock-names = "core", "reg";
+ clocks = <&CP11X_LABEL(clk) 1 26>,
+ <&CP11X_LABEL(clk) 1 17>;
+ dma-coherent;
+ };
+ };
+
+ CP11X_LABEL(pcie0): pcie@CP11X_PCIE0_BASE {
+ compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
+ reg = <0 ADDRESSIFY(CP11X_PCIE0_BASE) 0 0x10000>,
+ <0 CP11X_PCIEx_CONF_BASE(0) 0 0x80000>;
+ reg-names = "ctrl", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pci";
+ dma-coherent;
+ msi-parent = <&gic_v2m0>;
+
+ bus-range = <0 0xff>;
+ ranges =
+ /* downstream I/O */
+ <0x81000000 0 CP11X_PCIEx_IO_BASE(0) 0 CP11X_PCIEx_IO_BASE(0) 0 0x10000
+ /* non-prefetchable memory */
+ 0x82000000 0 CP11X_PCIEx_MEM_BASE(0) 0 CP11X_PCIEx_MEM_BASE(0) 0 0xf00000>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 22 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
+ num-lanes = <1>;
+ clock-names = "core", "reg";
+ clocks = <&CP11X_LABEL(clk) 1 13>, <&CP11X_LABEL(clk) 1 14>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(pcie1): pcie@CP11X_PCIE1_BASE {
+ compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
+ reg = <0 ADDRESSIFY(CP11X_PCIE1_BASE) 0 0x10000>,
+ <0 CP11X_PCIEx_CONF_BASE(1) 0 0x80000>;
+ reg-names = "ctrl", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pci";
+ dma-coherent;
+ msi-parent = <&gic_v2m0>;
+
+ bus-range = <0 0xff>;
+ ranges =
+ /* downstream I/O */
+ <0x81000000 0 CP11X_PCIEx_IO_BASE(1) 0 CP11X_PCIEx_IO_BASE(1) 0 0x10000
+ /* non-prefetchable memory */
+ 0x82000000 0 CP11X_PCIEx_MEM_BASE(1) 0 CP11X_PCIEx_MEM_BASE(1) 0 0xf00000>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 24 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH>;
+
+ num-lanes = <1>;
+ clock-names = "core", "reg";
+ clocks = <&CP11X_LABEL(clk) 1 11>, <&CP11X_LABEL(clk) 1 14>;
+ status = "disabled";
+ };
+
+ CP11X_LABEL(pcie2): pcie@CP11X_PCIE2_BASE {
+ compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
+ reg = <0 ADDRESSIFY(CP11X_PCIE2_BASE) 0 0x10000>,
+ <0 CP11X_PCIEx_CONF_BASE(2) 0 0x80000>;
+ reg-names = "ctrl", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pci";
+ dma-coherent;
+ msi-parent = <&gic_v2m0>;
+
+ bus-range = <0 0xff>;
+ ranges =
+ /* downstream I/O */
+ <0x81000000 0 CP11X_PCIEx_IO_BASE(2) 0 CP11X_PCIEx_IO_BASE(2) 0 0x10000
+ /* non-prefetchable memory */
+ 0x82000000 0 CP11X_PCIEx_MEM_BASE(2) 0 CP11X_PCIEx_MEM_BASE(2) 0 0xf00000>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 23 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
+
+ num-lanes = <1>;
+ clock-names = "core", "reg";
+ clocks = <&CP11X_LABEL(clk) 1 12>, <&CP11X_LABEL(clk) 1 14>;
+ status = "disabled";
+ };
+};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 13/21] arm64: dts: marvell: Drop PCIe I/O ranges from CP11x file
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (11 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 12/21] arm64: dts: marvell: Prepare the introduction of CP115 Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 14/21] arm64: dts: marvell: Externalize PCIe macros " Miquel Raynal
` (8 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
As an example, Armada 70x0 and 80x0 SoC 0xf9000000 region points to
RUNIT/SPICS0 while it is referenced in the DT as PCIe I/O memory
range. This shows that I/O memory has never been used/working on the
old SoCs despite the region being advertised. As PCIe I/O ranges will
not be supported in newer SoCs using CP11x co-processors, let's
simply drop them. It is not harmful in any case as PCIe device drivers
can do it all with the regular mapped memory anyway.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
arch/arm64/boot/dts/marvell/armada-70x0.dtsi | 2 --
.../boot/dts/marvell/armada-8040-mcbin.dtsi | 3 +--
arch/arm64/boot/dts/marvell/armada-80x0.dtsi | 4 ----
arch/arm64/boot/dts/marvell/armada-cp11x.dtsi | 16 +++-------------
4 files changed, 4 insertions(+), 21 deletions(-)
diff --git a/arch/arm64/boot/dts/marvell/armada-70x0.dtsi b/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
index 4e78ccd207b7..ac28903ea409 100644
--- a/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
@@ -19,7 +19,6 @@
*/
#define CP11X_NAME cp0
#define CP11X_BASE f2000000
-#define CP11X_PCIE_IO_BASE 0xf9000000
#define CP11X_PCIE_MEM_BASE 0xf6000000
#define CP11X_PCIE0_BASE f2600000
#define CP11X_PCIE1_BASE f2620000
@@ -29,7 +28,6 @@
#undef CP11X_NAME
#undef CP11X_BASE
-#undef CP11X_PCIE_IO_BASE
#undef CP11X_PCIE_MEM_BASE
#undef CP11X_PCIE0_BASE
#undef CP11X_PCIE1_BASE
diff --git a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi
index d250f4b2bfed..572e2610e0a3 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi
@@ -179,8 +179,7 @@
num-lanes = <4>;
num-viewport = <8>;
reset-gpios = <&cp0_gpio2 20 GPIO_ACTIVE_LOW>;
- ranges = <0x81000000 0x0 0xf9010000 0x0 0xf9010000 0x0 0x10000
- 0x82000000 0x0 0xc0000000 0x0 0xc0000000 0x0 0x20000000>;
+ ranges = <0x82000000 0x0 0xc0000000 0x0 0xc0000000 0x0 0x20000000>;
phys = <&cp0_comphy0 0>, <&cp0_comphy1 0>,
<&cp0_comphy2 0>, <&cp0_comphy3 0>;
phy-names = "cp0-pcie0-x4-lane0-phy", "cp0-pcie0-x4-lane1-phy",
diff --git a/arch/arm64/boot/dts/marvell/armada-80x0.dtsi b/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
index ebb98836ec9c..902eed571bcc 100644
--- a/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
@@ -21,7 +21,6 @@
*/
#define CP11X_NAME cp0
#define CP11X_BASE f2000000
-#define CP11X_PCIE_IO_BASE 0xf9000000
#define CP11X_PCIE_MEM_BASE 0xf6000000
#define CP11X_PCIE0_BASE f2600000
#define CP11X_PCIE1_BASE f2620000
@@ -31,7 +30,6 @@
#undef CP11X_NAME
#undef CP11X_BASE
-#undef CP11X_PCIE_IO_BASE
#undef CP11X_PCIE_MEM_BASE
#undef CP11X_PCIE0_BASE
#undef CP11X_PCIE1_BASE
@@ -42,7 +40,6 @@
*/
#define CP11X_NAME cp1
#define CP11X_BASE f4000000
-#define CP11X_PCIE_IO_BASE 0xfd000000
#define CP11X_PCIE_MEM_BASE 0xfa000000
#define CP11X_PCIE0_BASE f4600000
#define CP11X_PCIE1_BASE f4620000
@@ -52,7 +49,6 @@
#undef CP11X_NAME
#undef CP11X_BASE
-#undef CP11X_PCIE_IO_BASE
#undef CP11X_PCIE_MEM_BASE
#undef CP11X_PCIE0_BASE
#undef CP11X_PCIE1_BASE
diff --git a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
index 3e77cf34604c..7d1ab097453d 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
@@ -10,7 +10,6 @@
#include "armada-common.dtsi"
-#define CP11X_PCIEx_IO_BASE(iface) (CP11X_PCIE_IO_BASE + (iface * 0x10000))
#define CP11X_PCIEx_MEM_BASE(iface) (CP11X_PCIE_MEM_BASE + (iface * 0x1000000))
#define CP11X_PCIEx_CONF_BASE(iface) (CP11X_PCIEx_MEM_BASE(iface) + 0xf00000)
@@ -507,11 +506,8 @@
msi-parent = <&gic_v2m0>;
bus-range = <0 0xff>;
- ranges =
- /* downstream I/O */
- <0x81000000 0 CP11X_PCIEx_IO_BASE(0) 0 CP11X_PCIEx_IO_BASE(0) 0 0x10000
/* non-prefetchable memory */
- 0x82000000 0 CP11X_PCIEx_MEM_BASE(0) 0 CP11X_PCIEx_MEM_BASE(0) 0 0xf00000>;
+ ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(0) 0 CP11X_PCIEx_MEM_BASE(0) 0 0xf00000>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 22 IRQ_TYPE_LEVEL_HIGH>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
@@ -534,11 +530,8 @@
msi-parent = <&gic_v2m0>;
bus-range = <0 0xff>;
- ranges =
- /* downstream I/O */
- <0x81000000 0 CP11X_PCIEx_IO_BASE(1) 0 CP11X_PCIEx_IO_BASE(1) 0 0x10000
/* non-prefetchable memory */
- 0x82000000 0 CP11X_PCIEx_MEM_BASE(1) 0 CP11X_PCIEx_MEM_BASE(1) 0 0xf00000>;
+ ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(1) 0 CP11X_PCIEx_MEM_BASE(1) 0 0xf00000>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 24 IRQ_TYPE_LEVEL_HIGH>;
interrupts = <24 IRQ_TYPE_LEVEL_HIGH>;
@@ -562,11 +555,8 @@
msi-parent = <&gic_v2m0>;
bus-range = <0 0xff>;
- ranges =
- /* downstream I/O */
- <0x81000000 0 CP11X_PCIEx_IO_BASE(2) 0 CP11X_PCIEx_IO_BASE(2) 0 0x10000
/* non-prefetchable memory */
- 0x82000000 0 CP11X_PCIEx_MEM_BASE(2) 0 CP11X_PCIEx_MEM_BASE(2) 0 0xf00000>;
+ ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(2) 0 CP11X_PCIEx_MEM_BASE(2) 0 0xf00000>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 23 IRQ_TYPE_LEVEL_HIGH>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 14/21] arm64: dts: marvell: Externalize PCIe macros from CP11x file
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (12 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 13/21] arm64: dts: marvell: Drop PCIe I/O ranges from CP11x file Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 15/21] arm64: dts: marvell: Add support for CP115 Miquel Raynal
` (7 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
PCIe macros are specific to CP110 and will not fit CP115
constraints. To keep the same way the files are organized, just move
some macros out of the CP11x generic file and define them directly in
SoC DTSI, instead of defining single addresses in the SoC DTSI and
reusing them in macros.
In the end:
* CP11X_PCIE_MEM_BASE SoC define is dropped
* CP11X_PCIEx_MEM_BASE is moved out of the generic DT to be put in the
SoC files as it replaces the above definition.
* As the CP11X_PCIEx_MEM_SIZE macro is also subject to change with
newer SoCs, we put it in the SoC files as well.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
arch/arm64/boot/dts/marvell/armada-70x0.dtsi | 6 ++++--
arch/arm64/boot/dts/marvell/armada-80x0.dtsi | 12 ++++++++----
arch/arm64/boot/dts/marvell/armada-cp11x.dtsi | 9 ++++-----
3 files changed, 16 insertions(+), 11 deletions(-)
diff --git a/arch/arm64/boot/dts/marvell/armada-70x0.dtsi b/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
index ac28903ea409..293403a1a333 100644
--- a/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-70x0.dtsi
@@ -19,7 +19,8 @@
*/
#define CP11X_NAME cp0
#define CP11X_BASE f2000000
-#define CP11X_PCIE_MEM_BASE 0xf6000000
+#define CP11X_PCIEx_MEM_BASE(iface) (0xf6000000 + (iface * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
#define CP11X_PCIE0_BASE f2600000
#define CP11X_PCIE1_BASE f2620000
#define CP11X_PCIE2_BASE f2640000
@@ -28,7 +29,8 @@
#undef CP11X_NAME
#undef CP11X_BASE
-#undef CP11X_PCIE_MEM_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
#undef CP11X_PCIE0_BASE
#undef CP11X_PCIE1_BASE
#undef CP11X_PCIE2_BASE
diff --git a/arch/arm64/boot/dts/marvell/armada-80x0.dtsi b/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
index 902eed571bcc..ee67c70bf02e 100644
--- a/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-80x0.dtsi
@@ -21,7 +21,8 @@
*/
#define CP11X_NAME cp0
#define CP11X_BASE f2000000
-#define CP11X_PCIE_MEM_BASE 0xf6000000
+#define CP11X_PCIEx_MEM_BASE(iface) (0xf6000000 + (iface * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
#define CP11X_PCIE0_BASE f2600000
#define CP11X_PCIE1_BASE f2620000
#define CP11X_PCIE2_BASE f2640000
@@ -30,7 +31,8 @@
#undef CP11X_NAME
#undef CP11X_BASE
-#undef CP11X_PCIE_MEM_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
#undef CP11X_PCIE0_BASE
#undef CP11X_PCIE1_BASE
#undef CP11X_PCIE2_BASE
@@ -40,7 +42,8 @@
*/
#define CP11X_NAME cp1
#define CP11X_BASE f4000000
-#define CP11X_PCIE_MEM_BASE 0xfa000000
+#define CP11X_PCIEx_MEM_BASE(iface) (0xfa000000 + (iface * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
#define CP11X_PCIE0_BASE f4600000
#define CP11X_PCIE1_BASE f4620000
#define CP11X_PCIE2_BASE f4640000
@@ -49,7 +52,8 @@
#undef CP11X_NAME
#undef CP11X_BASE
-#undef CP11X_PCIE_MEM_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
#undef CP11X_PCIE0_BASE
#undef CP11X_PCIE1_BASE
#undef CP11X_PCIE2_BASE
diff --git a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
index 7d1ab097453d..9dcf16beabf5 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
@@ -10,8 +10,7 @@
#include "armada-common.dtsi"
-#define CP11X_PCIEx_MEM_BASE(iface) (CP11X_PCIE_MEM_BASE + (iface * 0x1000000))
-#define CP11X_PCIEx_CONF_BASE(iface) (CP11X_PCIEx_MEM_BASE(iface) + 0xf00000)
+#define CP11X_PCIEx_CONF_BASE(iface) (CP11X_PCIEx_MEM_BASE(iface) + CP11X_PCIEx_MEM_SIZE(iface))
/ {
/*
@@ -507,7 +506,7 @@
bus-range = <0 0xff>;
/* non-prefetchable memory */
- ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(0) 0 CP11X_PCIEx_MEM_BASE(0) 0 0xf00000>;
+ ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(0) 0 CP11X_PCIEx_MEM_BASE(0) 0 CP11X_PCIEx_MEM_SIZE(0)>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 22 IRQ_TYPE_LEVEL_HIGH>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
@@ -531,7 +530,7 @@
bus-range = <0 0xff>;
/* non-prefetchable memory */
- ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(1) 0 CP11X_PCIEx_MEM_BASE(1) 0 0xf00000>;
+ ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(1) 0 CP11X_PCIEx_MEM_BASE(1) 0 CP11X_PCIEx_MEM_SIZE(1)>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 24 IRQ_TYPE_LEVEL_HIGH>;
interrupts = <24 IRQ_TYPE_LEVEL_HIGH>;
@@ -556,7 +555,7 @@
bus-range = <0 0xff>;
/* non-prefetchable memory */
- ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(2) 0 CP11X_PCIEx_MEM_BASE(2) 0 0xf00000>;
+ ranges = <0x82000000 0 CP11X_PCIEx_MEM_BASE(2) 0 CP11X_PCIEx_MEM_BASE(2) 0 CP11X_PCIEx_MEM_SIZE(2)>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &CP11X_LABEL(icu_nsr) 23 IRQ_TYPE_LEVEL_HIGH>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 15/21] arm64: dts: marvell: Add support for CP115
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (13 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 14/21] arm64: dts: marvell: Externalize PCIe macros " Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 16/21] dt-bindings: marvell: Convert the SoC compatibles description to YAML Miquel Raynal
` (6 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
Create a DTSI file based on the CP11x one. Differences will be
described in the near future.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
arch/arm64/boot/dts/marvell/armada-cp115.dtsi | 12 ++++++++++++
1 file changed, 12 insertions(+)
create mode 100644 arch/arm64/boot/dts/marvell/armada-cp115.dtsi
diff --git a/arch/arm64/boot/dts/marvell/armada-cp115.dtsi b/arch/arm64/boot/dts/marvell/armada-cp115.dtsi
new file mode 100644
index 000000000000..1d0a9653e681
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-cp115.dtsi
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marvell Technology Group Ltd.
+ *
+ * Device Tree file for Marvell Armada CP115.
+ */
+
+#define CP11X_TYPE cp115
+
+#include "armada-cp11x.dtsi"
+
+#undef CP11X_TYPE
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 16/21] dt-bindings: marvell: Convert the SoC compatibles description to YAML
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (14 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 15/21] arm64: dts: marvell: Add support for CP115 Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 16:13 ` Rob Herring
2019-10-04 14:27 ` [PATCH v2 17/21] dt-bindings: marvell: Declare the CN913x SoC compatibles Miquel Raynal
` (5 subsequent siblings)
21 siblings, 1 reply; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
Convert the file detailing Marvell EBU compatibles to json-schema.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
.../bindings/arm/marvell/armada-7k-8k.txt | 24 -----------
.../bindings/arm/marvell/armada-7k-8k.yaml | 40 +++++++++++++++++++
2 files changed, 40 insertions(+), 24 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt
create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml
diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt
deleted file mode 100644
index df98a9c82a8c..000000000000
--- a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt
+++ /dev/null
@@ -1,24 +0,0 @@
-Marvell Armada 7K/8K Platforms Device Tree Bindings
----------------------------------------------------
-
-Boards using a SoC of the Marvell Armada 7K or 8K families must carry
-the following root node property:
-
- - compatible, with one of the following values:
-
- - "marvell,armada7020", "marvell,armada-ap806-dual", "marvell,armada-ap806"
- when the SoC being used is the Armada 7020
-
- - "marvell,armada7040", "marvell,armada-ap806-quad", "marvell,armada-ap806"
- when the SoC being used is the Armada 7040
-
- - "marvell,armada8020", "marvell,armada-ap806-dual", "marvell,armada-ap806"
- when the SoC being used is the Armada 8020
-
- - "marvell,armada8040", "marvell,armada-ap806-quad", "marvell,armada-ap806"
- when the SoC being used is the Armada 8040
-
-Example:
-
-compatible = "marvell,armada7040-db", "marvell,armada7040",
- "marvell,armada-ap806-quad", "marvell,armada-ap806";
diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml
new file mode 100644
index 000000000000..294595e00028
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml
@@ -0,0 +1,40 @@
+# SPDX-License-Identifier: (GPL-2.0+ OR X11)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/arm/marvell/armada-7k-8k.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell Armada 7K/8K Platforms Device Tree Bindings
+
+maintainers:
+ - Gregory CLEMENT <gregory.clement@bootlin.com>
+
+properties:
+ $nodename:
+ const: '/'
+ compatible:
+ oneOf:
+
+ - description: Armada 7020 SoC
+ items:
+ - const: marvell,armada7020
+ - const: marvell,armada-ap806-dual
+ - const: marvell,armada-ap806
+
+ - description: Armada 7040 SoC
+ items:
+ - const: marvell,armada7040
+ - const: marvell,armada-ap806-quad
+ - const: marvell,armada-ap806
+
+ - description: Armada 8020 SoC
+ items:
+ - const: marvell,armada8020
+ - const: marvell,armada-ap806-dual
+ - const: marvell,armada-ap806
+
+ - description: Armada 8040 SoC
+ items:
+ - const: marvell,armada8040
+ - const: marvell,armada-ap806-quad
+ - const: marvell,armada-ap806
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 17/21] dt-bindings: marvell: Declare the CN913x SoC compatibles
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (15 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 16/21] dt-bindings: marvell: Convert the SoC compatibles description to YAML Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 16:14 ` Rob Herring
2019-10-04 14:27 ` [PATCH v2 18/21] arm64: dts: marvell: Add support for Marvell CN9130 SoC support Miquel Raynal
` (4 subsequent siblings)
21 siblings, 1 reply; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
From: Grzegorz Jaszczyk <jaz@semihalf.com>
Describe the compatible properties for the new Marvell SoCs:
* CN9130: 1x AP807-quad + 1x CP115 (1x embedded)
* CN9131: 1x AP807-quad + 2x CP115 (1x embedded + 1x modular)
* CN9132: 1x AP807-quad + 3x CP115 (1x embedded + 2x modular)
CP115 are similar to CP110 in terms of features.
There are three development boards based on these SoCs:
* CN9130-DB: comes as a single mother board (with the CP115 bundled)
* CN9131-DB: same as CN9130-DB with one additional modular CP115
* CN9132-DB: same as CN9130-DB with two additional modular CP115
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
.../bindings/arm/marvell/armada-7k-8k.yaml | 21 +++++++++++++++++++
1 file changed, 21 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml
index 294595e00028..a9828c50c0fb 100644
--- a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml
+++ b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml
@@ -38,3 +38,24 @@ properties:
- const: marvell,armada8040
- const: marvell,armada-ap806-quad
- const: marvell,armada-ap806
+
+ - description: Armada CN9130 SoC with no external CP
+ items:
+ - const: marvell,cn9130
+ - const: marvell,armada-ap807-quad
+ - const: marvell,armada-ap807
+
+ - description: Armada CN9131 SoC with one external CP
+ items:
+ - const: marvell,cn9131
+ - const: marvell,cn9130
+ - const: marvell,armada-ap807-quad
+ - const: marvell,armada-ap807
+
+ - description: Armada CN9132 SoC with two external CPs
+ items:
+ - const: marvell,cn9132
+ - const: marvell,cn9131
+ - const: marvell,cn9130
+ - const: marvell,armada-ap807-quad
+ - const: marvell,armada-ap807
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 18/21] arm64: dts: marvell: Add support for Marvell CN9130 SoC support
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (16 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 17/21] dt-bindings: marvell: Declare the CN913x SoC compatibles Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 19/21] arm64: dts: marvell: Add support for Marvell CN9130-DB Miquel Raynal
` (3 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
A CN9130 SoC has one AP807 and one internal CP115.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
arch/arm64/boot/dts/marvell/cn9130.dtsi | 37 +++++++++++++++++++++++++
1 file changed, 37 insertions(+)
create mode 100644 arch/arm64/boot/dts/marvell/cn9130.dtsi
diff --git a/arch/arm64/boot/dts/marvell/cn9130.dtsi b/arch/arm64/boot/dts/marvell/cn9130.dtsi
new file mode 100644
index 000000000000..a2b7e5ec979d
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marvell International Ltd.
+ *
+ * Device tree for the CN9130 SoC.
+ */
+
+#include "armada-ap807-quad.dtsi"
+
+/ {
+ model = "Marvell Armada CN9130 SoC";
+ compatible = "marvell,cn9130", "marvell,armada-ap807-quad",
+ "marvell,armada-ap807";
+};
+
+/*
+ * Instantiate the internal CP115
+ */
+
+#define CP11X_NAME cp0
+#define CP11X_BASE f2000000
+#define CP11X_PCIEx_MEM_BASE(iface) ((iface == 0) ? 0xc0000000 : \
+ 0xe0000000 + ((iface - 1) * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) ((iface == 0) ? 0x1ff00000 : 0xf00000)
+#define CP11X_PCIE0_BASE f2600000
+#define CP11X_PCIE1_BASE f2620000
+#define CP11X_PCIE2_BASE f2640000
+
+#include "armada-cp115.dtsi"
+
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 19/21] arm64: dts: marvell: Add support for Marvell CN9130-DB
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (17 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 18/21] arm64: dts: marvell: Add support for Marvell CN9130 SoC support Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 20/21] arm64: dts: marvell: Add support for Marvell CN9131-DB Miquel Raynal
` (2 subsequent siblings)
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
From: Grzegorz Jaszczyk <jaz@semihalf.com>
Add basic support for the Marvell CN9130 modular development board. It
is based on a CN9130 SoC (one AP807 and one internal CP115), extended
via 2xMoCi interface to possibly add up to two more external CP115
(one located on the main board and the other on the board extension).
Available interfaces:
* AP UART
* AP eMMC
* AP SDHCI (disabled)
* CPO GPIO-0
* CPO GPIO-1
* CP0 CRYPTO-0 (disabled)
* CP0 I2C-0
* CP0 I2C-1
* CP0 SDHCI-0
* CP0 NAND-0
* CP0 SPI-1
* CP0 ETH-0 (SFI with SFP cage not working yet, disabled)
* CP0 ETH-1 (RGMII)
* CP0 ETH-2 (RGMII)
* CP0 SATA-0-1
* CP0 USB3-0 (High-speed only)
* CP0 USB3-1 (High-speed only)
* CP0 PCIe-0 x4
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
arch/arm64/boot/dts/marvell/Makefile | 1 +
arch/arm64/boot/dts/marvell/cn9130-db.dts | 403 ++++++++++++++++++++++
2 files changed, 404 insertions(+)
create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dts
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 243338c914a4..70cac6127148 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -10,3 +10,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db.dtb
diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dts b/arch/arm64/boot/dts/marvell/cn9130-db.dts
new file mode 100644
index 000000000000..ce49a70d88a0
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-db.dts
@@ -0,0 +1,403 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marvell International Ltd.
+ *
+ * Device tree for the CN9130-DB board.
+ */
+
+#include "cn9130.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Marvell Armada CN9130-DB";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ aliases {
+ gpio1 = &cp0_gpio1;
+ gpio2 = &cp0_gpio2;
+ i2c0 = &cp0_i2c0;
+ ethernet0 = &cp0_eth0;
+ ethernet1 = &cp0_eth1;
+ ethernet2 = &cp0_eth2;
+ spi1 = &cp0_spi0;
+ spi2 = &cp0_spi1;
+ };
+
+ memory@00000000 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ ap0_reg_sd_vccq: ap0_sd_vccq@0 {
+ compatible = "regulator-gpio";
+ regulator-name = "ap0_sd_vccq";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&expander0 8 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1 3300000 0x0>;
+ };
+
+ cp0_reg_usb3_vbus0: cp0_usb3_vbus@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp0-xhci0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ cp0_usb3_0_phy0: cp0_usb3_phy@0 {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <&cp0_reg_usb3_vbus0>;
+ };
+
+ cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp0-xhci1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ cp0_usb3_0_phy1: cp0_usb3_phy@1 {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <&cp0_reg_usb3_vbus1>;
+ };
+
+ cp0_reg_sd_vccq: cp0_sd_vccq@0 {
+ compatible = "regulator-gpio";
+ regulator-name = "cp0_sd_vccq";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&expander0 15 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ };
+
+ cp0_reg_sd_vcc: cp0_sd_vcc@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp0_sd_vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&expander0 14 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ cp0_sfp_eth0: sfp-eth@0 {
+ compatible = "sff,sfp";
+ i2c-bus = <&cp0_sfpp0_i2c>;
+ los-gpio = <&cp0_module_expander1 11 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&cp0_module_expander1 10 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&cp0_module_expander1 9 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&cp0_module_expander1 8 GPIO_ACTIVE_HIGH>;
+ /*
+ * SFP cages are unconnected on early PCBs because of an the I2C
+ * lanes not being connected. Prevent the port for being
+ * unusable by disabling the SFP node.
+ */
+ status = "disabled";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+/* on-board eMMC - U9 */
+&ap_sdhci0 {
+ pinctrl-names = "default";
+ bus-width = <8>;
+ vqmmc-supply = <&ap0_reg_sd_vccq>;
+ status = "okay";
+};
+
+&cp0_crypto {
+ status = "disabled";
+};
+
+&cp0_ethernet {
+ status = "okay";
+};
+
+/* SLM-1521-V2, CON9 */
+&cp0_eth0 {
+ status = "disabled";
+ phy-mode = "10gbase-kr";
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp0_comphy4 0>;
+ managed = "in-band-status";
+ sfp = <&cp0_sfp_eth0>;
+};
+
+/* CON56 */
+&cp0_eth1 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+};
+
+/* CON57 */
+&cp0_eth2 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+};
+
+&cp0_gpio1 {
+ status = "okay";
+};
+
+&cp0_gpio2 {
+ status = "okay";
+};
+
+&cp0_i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_i2c0_pins>;
+ clock-frequency = <100000>;
+
+ /* U36 */
+ expander0: pca953x@21 {
+ compatible = "nxp,pca9555";
+ pinctrl-names = "default";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x21>;
+ status = "okay";
+ };
+
+ /* U42 */
+ eeprom0: eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ pagesize = <0x20>;
+ };
+
+ /* U38 */
+ eeprom1: eeprom@57 {
+ compatible = "atmel,24c64";
+ reg = <0x57>;
+ pagesize = <0x20>;
+ };
+};
+
+&cp0_i2c1 {
+ status = "okay";
+ clock-frequency = <100000>;
+
+ /* SLM-1521-V2 - U3 */
+ i2c-mux@72 { /* verify address - depends on dpr */
+ compatible = "nxp,pca9544";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x72>;
+ cp0_sfpp0_i2c: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ /* U12 */
+ cp0_module_expander1: pca9555@21 {
+ compatible = "nxp,pca9555";
+ pinctrl-names = "default";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x21>;
+ };
+
+ };
+ };
+};
+
+&cp0_mdio {
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+/* U54 */
+&cp0_nand_controller {
+ pinctrl-names = "default";
+ pinctrl-0 = <&nand_pins &nand_rb>;
+
+ nand@0 {
+ reg = <0>;
+ label = "main-storage";
+ nand-rb = <0>;
+ nand-ecc-mode = "hw";
+ nand-on-flash-bbt;
+ nand-ecc-strength = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "U-Boot";
+ reg = <0 0x200000>;
+ };
+ partition@200000 {
+ label = "Linux";
+ reg = <0x200000 0xd00000>;
+ };
+ partition@1000000 {
+ label = "Filesystem";
+ reg = <0x1000000 0x3f000000>;
+ };
+ };
+ };
+};
+
+/* SLM-1521-V2, CON6 */
+&cp0_pcie0 {
+ status = "okay";
+ num-lanes = <4>;
+ num-viewport = <8>;
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp0_comphy0 0
+ &cp0_comphy1 0
+ &cp0_comphy2 0
+ &cp0_comphy3 0>;
+};
+
+&cp0_sata0 {
+ status = "okay";
+
+ /* SLM-1521-V2, CON2 */
+ sata-port@1 {
+ status = "okay";
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp0_comphy5 1>;
+ };
+};
+
+/* CON 28 */
+&cp0_sdhci0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_sdhci_pins
+ &cp0_sdhci_cd_pins>;
+ bus-width = <4>;
+ cd-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ vqmmc-supply = <&cp0_reg_sd_vccq>;
+ vmmc-supply = <&cp0_reg_sd_vcc>;
+};
+
+/* U55 */
+&cp0_spi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_spi0_pins>;
+ reg = <0x700680 0x50>;
+
+ spi-flash@0 {
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ /* On-board MUX does not allow higher frequencies */
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "U-Boot-0";
+ reg = <0x0 0x200000>;
+ };
+
+ partition@400000 {
+ label = "Filesystem-0";
+ reg = <0x200000 0xe00000>;
+ };
+ };
+ };
+};
+
+&cp0_syscon0 {
+ cp0_pinctrl: pinctrl {
+ compatible = "marvell,cp115-standalone-pinctrl";
+
+ cp0_i2c0_pins: cp0-i2c-pins-0 {
+ marvell,pins = "mpp37", "mpp38";
+ marvell,function = "i2c0";
+ };
+ cp0_i2c1_pins: cp0-i2c-pins-1 {
+ marvell,pins = "mpp35", "mpp36";
+ marvell,function = "i2c1";
+ };
+ cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 {
+ marvell,pins = "mpp0", "mpp1", "mpp2",
+ "mpp3", "mpp4", "mpp5",
+ "mpp6", "mpp7", "mpp8",
+ "mpp9", "mpp10", "mpp11";
+ marvell,function = "ge0";
+ };
+ cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 {
+ marvell,pins = "mpp44", "mpp45", "mpp46",
+ "mpp47", "mpp48", "mpp49",
+ "mpp50", "mpp51", "mpp52",
+ "mpp53", "mpp54", "mpp55";
+ marvell,function = "ge1";
+ };
+ cp0_sdhci_cd_pins: cp0-sdhci-cd-pins-0 {
+ marvell,pins = "mpp43";
+ marvell,function = "gpio";
+ };
+ cp0_sdhci_pins: cp0-sdhi-pins-0 {
+ marvell,pins = "mpp56", "mpp57", "mpp58",
+ "mpp59", "mpp60", "mpp61";
+ marvell,function = "sdio";
+ };
+ cp0_spi0_pins: cp0-spi-pins-0 {
+ marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+ marvell,function = "spi1";
+ };
+ nand_pins: nand-pins {
+ marvell,pins = "mpp15", "mpp16", "mpp17", "mpp18",
+ "mpp19", "mpp20", "mpp21", "mpp22",
+ "mpp23", "mpp24", "mpp25", "mpp26",
+ "mpp27";
+ marvell,function = "dev";
+ };
+ nand_rb: nand-rb {
+ marvell,pins = "mpp13";
+ marvell,function = "nf";
+ };
+ };
+};
+
+&cp0_usb3_0 {
+ status = "okay";
+ usb-phy = <&cp0_usb3_0_phy0>;
+ phy-names = "usb";
+};
+
+&cp0_usb3_1 {
+ status = "okay";
+ usb-phy = <&cp0_usb3_0_phy1>;
+ phy-names = "usb";
+};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 20/21] arm64: dts: marvell: Add support for Marvell CN9131-DB
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (18 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 19/21] arm64: dts: marvell: Add support for Marvell CN9130-DB Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 21/21] arm64: dts: marvell: Add support for Marvell CN9132-DB Miquel Raynal
2019-10-08 12:25 ` [PATCH v2 00/21] Add new Marvell CN9130 SoC support Gregory CLEMENT
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
From: Grzegorz Jaszczyk <jaz@semihalf.com>
Extend the support of the CN9130 by adding an external CP115.
The last number indicates how many external CP115 are used.
New available interfaces:
* CP1 CRYPTO-0 (disabled)
* CP1 ETH-0 (SFI, problem with the SFP cage, disabled)
* CP1 GPIO-1
* CP1 GPIO-2
* CP1 I2C-0
* CP1 PCIe-0 x2
* CP1 SPI-1
* CP1 SATA-0-1
* CP1 USB3-1
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
arch/arm64/boot/dts/marvell/Makefile | 1 +
arch/arm64/boot/dts/marvell/cn9131-db.dts | 202 ++++++++++++++++++++++
2 files changed, 203 insertions(+)
create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dts
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 70cac6127148..9fbf8f460153 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -11,3 +11,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb
diff --git a/arch/arm64/boot/dts/marvell/cn9131-db.dts b/arch/arm64/boot/dts/marvell/cn9131-db.dts
new file mode 100644
index 000000000000..3c975f98b2a3
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9131-db.dts
@@ -0,0 +1,202 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marvell International Ltd.
+ *
+ * Device tree for the CN9131-DB board.
+ */
+
+#include "cn9130-db.dts"
+
+/ {
+ model = "Marvell Armada CN9131-DB";
+ compatible = "marvell,cn9131", "marvell,cn9130",
+ "marvell,armada-ap807-quad", "marvell,armada-ap807";
+
+ aliases {
+ gpio3 = &cp1_gpio1;
+ gpio4 = &cp1_gpio2;
+ ethernet3 = &cp1_eth0;
+ ethernet4 = &cp1_eth1;
+ };
+
+ cp1_reg_usb3_vbus0: cp1_usb3_vbus@0 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp1_xhci0_vbus_pins>;
+ regulator-name = "cp1-xhci0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&cp1_gpio1 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ cp1_usb3_0_phy0: cp1_usb3_phy0 {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <&cp1_reg_usb3_vbus0>;
+ };
+
+ cp1_sfp_eth1: sfp-eth1 {
+ compatible = "sff,sfp";
+ i2c-bus = <&cp1_i2c0>;
+ los-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&cp1_gpio1 9 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp1_sfp_pins>;
+ /*
+ * SFP cages are unconnected on early PCBs because of an the I2C
+ * lanes not being connected. Prevent the port for being
+ * unusable by disabling the SFP node.
+ */
+ status = "disabled";
+ };
+};
+
+/*
+ * Instantiate the first slave CP115
+ */
+
+#define CP11X_NAME cp1
+#define CP11X_BASE f4000000
+#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
+#define CP11X_PCIE0_BASE f4600000
+#define CP11X_PCIE1_BASE f4620000
+#define CP11X_PCIE2_BASE f4640000
+
+#include "armada-cp115.dtsi"
+
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
+
+&cp1_crypto {
+ status = "disabled";
+};
+
+&cp1_ethernet {
+ status = "okay";
+};
+
+/* CON50 */
+&cp1_eth0 {
+ status = "disabled";
+ phy-mode = "10gbase-kr";
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp1_comphy4 0>;
+ managed = "in-band-status";
+ sfp = <&cp1_sfp_eth1>;
+};
+
+&cp1_gpio1 {
+ status = "okay";
+};
+
+&cp1_gpio2 {
+ status = "okay";
+};
+
+&cp1_i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp1_i2c0_pins>;
+ clock-frequency = <100000>;
+};
+
+/* CON40 */
+&cp1_pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp1_pcie_reset_pins>;
+ num-lanes = <2>;
+ num-viewport = <8>;
+ marvell,reset-gpio = <&cp1_gpio1 0 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp1_comphy0 0
+ &cp1_comphy1 0>;
+};
+
+&cp1_sata0 {
+ status = "okay";
+
+ /* CON32 */
+ sata-port@1 {
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp1_comphy5 1>;
+ };
+};
+
+/* U24 */
+&cp1_spi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp1_spi0_pins>;
+ reg = <0x700680 0x50>;
+
+ spi-flash@0 {
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ /* On-board MUX does not allow higher frequencies */
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "U-Boot-1";
+ reg = <0x0 0x200000>;
+ };
+
+ partition@400000 {
+ label = "Filesystem-1";
+ reg = <0x200000 0xe00000>;
+ };
+ };
+ };
+
+};
+
+&cp1_syscon0 {
+ cp1_pinctrl: pinctrl {
+ compatible = "marvell,cp115-standalone-pinctrl";
+
+ cp1_i2c0_pins: cp1-i2c-pins-0 {
+ marvell,pins = "mpp37", "mpp38";
+ marvell,function = "i2c0";
+ };
+ cp1_spi0_pins: cp1-spi-pins-0 {
+ marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+ marvell,function = "spi1";
+ };
+ cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins {
+ marvell,pins = "mpp3";
+ marvell,function = "gpio";
+ };
+ cp1_sfp_pins: sfp-pins {
+ marvell,pins = "mpp8", "mpp9", "mpp10", "mpp11";
+ marvell,function = "gpio";
+ };
+ cp1_pcie_reset_pins: cp1-pcie-reset-pins {
+ marvell,pins = "mpp0";
+ marvell,function = "gpio";
+ };
+ };
+};
+
+/* CON58 */
+&cp1_usb3_1 {
+ status = "okay";
+ usb-phy = <&cp1_usb3_0_phy0>;
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp1_comphy3 1>;
+ phy-names = "usb";
+};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* [PATCH v2 21/21] arm64: dts: marvell: Add support for Marvell CN9132-DB
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (19 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 20/21] arm64: dts: marvell: Add support for Marvell CN9131-DB Miquel Raynal
@ 2019-10-04 14:27 ` Miquel Raynal
2019-10-08 12:25 ` [PATCH v2 00/21] Add new Marvell CN9130 SoC support Gregory CLEMENT
21 siblings, 0 replies; 25+ messages in thread
From: Miquel Raynal @ 2019-10-04 14:27 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Gregory Clement, Maxime Chevallier, Nadav Haklai,
Thomas Petazzoni, Miquel Raynal, Stefan Chulski, Marcin Wojtas,
linux-arm-kernel
From: Grzegorz Jaszczyk <jaz@semihalf.com>
Extend the support of the CN9131 with yet another additional CP115.
The last number indicates how many external CP115 are used.
New available interfaces:
* CP2 CRYPTO-0 (disabled)
* CP2 ETH-0 (SFI, problem with the SFP cage, disabled)
* CP2 GPIO-1
* CP2 GPIO-2
* CP2 I2C-0
* CP2 PCIe-0 x2
* CP2 PCIe-2 x1 (disabled)
* CP2 SDHCI-0
* CP2 USB3-1 (High-speed)
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
arch/arm64/boot/dts/marvell/Makefile | 1 +
arch/arm64/boot/dts/marvell/cn9132-db.dts | 221 ++++++++++++++++++++++
2 files changed, 222 insertions(+)
create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dts
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 9fbf8f460153..f1b5127f0b89 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -12,3 +12,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb
diff --git a/arch/arm64/boot/dts/marvell/cn9132-db.dts b/arch/arm64/boot/dts/marvell/cn9132-db.dts
new file mode 100644
index 000000000000..4ef0df3097ca
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9132-db.dts
@@ -0,0 +1,221 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marvell International Ltd.
+ *
+ * Device tree for the CN9132-DB board.
+ */
+
+#include "cn9131-db.dts"
+
+/ {
+ model = "Marvell Armada CN9132-DB";
+ compatible = "marvell,cn9132", "marvell,cn9131", "marvell,cn9130",
+ "marvell,armada-ap807-quad", "marvell,armada-ap807";
+
+ aliases {
+ gpio5 = &cp2_gpio1;
+ gpio6 = &cp2_gpio2;
+ ethernet5 = &cp2_eth0;
+ };
+
+ cp2_reg_usb3_vbus0: cp2_usb3_vbus@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp2-xhci0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&cp2_gpio1 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ cp2_usb3_0_phy0: cp2_usb3_phy0 {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <&cp2_reg_usb3_vbus0>;
+ };
+
+ cp2_reg_usb3_vbus1: cp2_usb3_vbus@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp2-xhci1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&cp2_gpio1 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ cp2_usb3_0_phy1: cp2_usb3_phy1 {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <&cp2_reg_usb3_vbus1>;
+ };
+
+ cp2_reg_sd_vccq: cp2_sd_vccq@0 {
+ compatible = "regulator-gpio";
+ regulator-name = "cp2_sd_vcc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&cp2_gpio2 17 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1 3300000 0x0>;
+ };
+
+ cp2_sfp_eth0: sfp-eth0 {
+ compatible = "sff,sfp";
+ i2c-bus = <&cp2_sfpp0_i2c>;
+ los-gpio = <&cp2_module_expander1 11 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&cp2_module_expander1 10 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&cp2_module_expander1 9 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&cp2_module_expander1 8 GPIO_ACTIVE_HIGH>;
+ /*
+ * SFP cages are unconnected on early PCBs because of an the I2C
+ * lanes not being connected. Prevent the port for being
+ * unusable by disabling the SFP node.
+ */
+ status = "disabled";
+ };
+};
+
+/*
+ * Instantiate the second slave CP115
+ */
+
+#define CP11X_NAME cp2
+#define CP11X_BASE f6000000
+#define CP11X_PCIEx_MEM_BASE(iface) (0xe5000000 + (iface * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
+#define CP11X_PCIE0_BASE f6600000
+#define CP11X_PCIE1_BASE f6620000
+#define CP11X_PCIE2_BASE f6640000
+
+#include "armada-cp115.dtsi"
+
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
+
+&cp2_crypto {
+ status = "disabled";
+};
+
+&cp2_ethernet {
+ status = "okay";
+};
+
+/* SLM-1521-V2, CON9 */
+&cp2_eth0 {
+ status = "disabled";
+ phy-mode = "10gbase-kr";
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp2_comphy4 0>;
+ managed = "in-band-status";
+ sfp = <&cp2_sfp_eth0>;
+};
+
+&cp2_gpio1 {
+ status = "okay";
+};
+
+&cp2_gpio2 {
+ status = "okay";
+};
+
+&cp2_i2c0 {
+ clock-frequency = <100000>;
+
+ /* SLM-1521-V2 - U3 */
+ i2c-mux@72 {
+ compatible = "nxp,pca9544";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x72>;
+ cp2_sfpp0_i2c: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ /* U12 */
+ cp2_module_expander1: pca9555@21 {
+ compatible = "nxp,pca9555";
+ pinctrl-names = "default";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x21>;
+ };
+ };
+ };
+};
+
+/* SLM-1521-V2, CON6 */
+&cp2_pcie0 {
+ status = "okay";
+ num-lanes = <2>;
+ num-viewport = <8>;
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp2_comphy0 0
+ &cp2_comphy1 0>;
+};
+
+/* SLM-1521-V2, CON8 */
+&cp2_pcie2 {
+ status = "okay";
+ num-lanes = <1>;
+ num-viewport = <8>;
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp2_comphy5 2>;
+};
+
+&cp2_sata0 {
+ status = "okay";
+
+ /* SLM-1521-V2, CON4 */
+ sata-port@0 {
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp2_comphy2 0>;
+ };
+};
+
+/* CON 2 on SLM-1683 - microSD */
+&cp2_sdhci0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp2_sdhci_pins>;
+ bus-width = <4>;
+ cd-gpios = <&cp2_gpio2 23 GPIO_ACTIVE_LOW>;
+ vqmmc-supply = <&cp2_reg_sd_vccq>;
+};
+
+&cp2_syscon0 {
+ cp2_pinctrl: pinctrl {
+ compatible = "marvell,cp115-standalone-pinctrl";
+
+ cp2_i2c0_pins: cp2-i2c-pins-0 {
+ marvell,pins = "mpp37", "mpp38";
+ marvell,function = "i2c0";
+ };
+ cp2_sdhci_pins: cp2-sdhi-pins-0 {
+ marvell,pins = "mpp56", "mpp57", "mpp58",
+ "mpp59", "mpp60", "mpp61";
+ marvell,function = "sdio";
+ };
+ };
+};
+
+&cp2_usb3_0 {
+ status = "okay";
+ usb-phy = <&cp2_usb3_0_phy0>;
+ phy-names = "usb";
+};
+
+/* SLM-1521-V2, CON11 */
+&cp2_usb3_1 {
+ status = "okay";
+ usb-phy = <&cp2_usb3_0_phy1>;
+ phy-names = "usb";
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp2_comphy3 1>;
+};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 25+ messages in thread
* Re: [PATCH v2 16/21] dt-bindings: marvell: Convert the SoC compatibles description to YAML
2019-10-04 14:27 ` [PATCH v2 16/21] dt-bindings: marvell: Convert the SoC compatibles description to YAML Miquel Raynal
@ 2019-10-04 16:13 ` Rob Herring
0 siblings, 0 replies; 25+ messages in thread
From: Rob Herring @ 2019-10-04 16:13 UTC (permalink / raw)
To: Miquel Raynal
Cc: Mark Rutland, devicetree, Yan Markman, Antoine Tenart,
Grzegorz Jaszczyk, Gregory Clement, Maxime Chevallier,
Nadav Haklai, Thomas Petazzoni, Stefan Chulski, Marcin Wojtas,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
On Fri, Oct 4, 2019 at 9:28 AM Miquel Raynal <miquel.raynal@bootlin.com> wrote:
>
> Convert the file detailing Marvell EBU compatibles to json-schema.
>
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
> .../bindings/arm/marvell/armada-7k-8k.txt | 24 -----------
> .../bindings/arm/marvell/armada-7k-8k.yaml | 40 +++++++++++++++++++
> 2 files changed, 40 insertions(+), 24 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt
> create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml
Reviewed-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [PATCH v2 17/21] dt-bindings: marvell: Declare the CN913x SoC compatibles
2019-10-04 14:27 ` [PATCH v2 17/21] dt-bindings: marvell: Declare the CN913x SoC compatibles Miquel Raynal
@ 2019-10-04 16:14 ` Rob Herring
0 siblings, 0 replies; 25+ messages in thread
From: Rob Herring @ 2019-10-04 16:14 UTC (permalink / raw)
To: Miquel Raynal
Cc: Mark Rutland, devicetree, Yan Markman, Antoine Tenart,
Grzegorz Jaszczyk, Gregory Clement, Maxime Chevallier,
Nadav Haklai, Thomas Petazzoni, Stefan Chulski, Marcin Wojtas,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
On Fri, Oct 4, 2019 at 9:28 AM Miquel Raynal <miquel.raynal@bootlin.com> wrote:
>
> From: Grzegorz Jaszczyk <jaz@semihalf.com>
>
> Describe the compatible properties for the new Marvell SoCs:
> * CN9130: 1x AP807-quad + 1x CP115 (1x embedded)
> * CN9131: 1x AP807-quad + 2x CP115 (1x embedded + 1x modular)
> * CN9132: 1x AP807-quad + 3x CP115 (1x embedded + 2x modular)
>
> CP115 are similar to CP110 in terms of features.
>
> There are three development boards based on these SoCs:
> * CN9130-DB: comes as a single mother board (with the CP115 bundled)
> * CN9131-DB: same as CN9130-DB with one additional modular CP115
> * CN9132-DB: same as CN9130-DB with two additional modular CP115
>
> Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
> .../bindings/arm/marvell/armada-7k-8k.yaml | 21 +++++++++++++++++++
> 1 file changed, 21 insertions(+)
Reviewed-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [PATCH v2 00/21] Add new Marvell CN9130 SoC support
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
` (20 preceding siblings ...)
2019-10-04 14:27 ` [PATCH v2 21/21] arm64: dts: marvell: Add support for Marvell CN9132-DB Miquel Raynal
@ 2019-10-08 12:25 ` Gregory CLEMENT
21 siblings, 0 replies; 25+ messages in thread
From: Gregory CLEMENT @ 2019-10-08 12:25 UTC (permalink / raw)
To: Miquel Raynal, Rob Herring, Mark Rutland
Cc: devicetree, Yan Markman, Antoine Tenart, Grzegorz Jaszczyk,
Maxime Chevallier, Nadav Haklai, Thomas Petazzoni, Miquel Raynal,
Stefan Chulski, Marcin Wojtas, linux-arm-kernel
Hi Miquel,
> Hello,
>
> This is a respin of the last remaining patchset needed to fully support
> Marvell CN9130 SoCs. The CN9130 is made of one AP807 and one internal
> CP115. There are three development boards that are made of this SoC:
> * CN9130-DB
> * CN9131-DB (with one additional modular CP115 compared to CN9130-DB)
> * CN9132-DB (with two additional modular CP115 compared to CN9130-DB)
>
> This series applies on top of v5.4-rc1 and works thanks to the
> previously merged following series:
> * CP110 COMPHY:
> https://patchwork.kernel.org/cover/11067647/
> * AP806 CPU clocks:
> https://patchwork.kernel.org/cover/11038577/
> * AP807 clocks:
> https://patchwork.kernel.org/cover/11076435/
> * CP115 pinctrl:
> http://patchwork.ozlabs.org/cover/1142107/
>
> As CP110 and CP115 (alternatively, AP806 and AP807) are very similar,
> we first reorganize DT files to create CP11x (and AP80x) generic
> files, before including them from the new specific CP110/CP115
> (AP806/AP807) ones.
>
> A few small improvements/fixes in these files are also carried.
>
> Thanks,
> Miquèl
>
> Changes since v1:
> =================
> * Rebased on top of v5.4-rc1.
> * Rob's Reviewed-by tag on the first bindings patch (03).
> * Used the AP_NAME macro instead of hardcoding ap806 in the DT which
> turns generic (spotted by Gregory).
> * Converted Marvell SoC compatible bindings to yaml (patch 16) as
> requested by Rob. Add Gregory as the file maintainer.
>
>
> Ben Peled (1):
> dt-bindings: ap80x: replace AP806 with AP80x
>
> Grzegorz Jaszczyk (7):
> arm64: dts: marvell: Add AP806-dual cache description
> arm64: dts: marvell: Add AP806-quad cache description
> arm64: dts: marvell: Add AP807-quad cache description
> dt-bindings: marvell: Declare the CN913x SoC compatibles
> arm64: dts: marvell: Add support for Marvell CN9130-DB
> arm64: dts: marvell: Add support for Marvell CN9131-DB
> arm64: dts: marvell: Add support for Marvell CN9132-DB
>
> Konstantin Porotchkin (1):
> arm64: dts: marvell: Prepare the introduction of AP807 based SoCs
>
> Miquel Raynal (12):
> arm64: dts: marvell: Enumerate the first AP806 syscon
> arm64: dts: marvell: Add AP806-dual missing CPU clocks
> MAINTAINERS: Add new Marvell CN9130-based files to track
> arm64: dts: marvell: Move clocks to AP806 specific file
> arm64: dts: marvell: Add support for AP807/AP807-quad
> arm64: dts: marvell: Fix CP110 NAND controller node multi-line comment
> alignment
> arm64: dts: marvell: Prepare the introduction of CP115
> arm64: dts: marvell: Drop PCIe I/O ranges from CP11x file
> arm64: dts: marvell: Externalize PCIe macros from CP11x file
> arm64: dts: marvell: Add support for CP115
> dt-bindings: marvell: Convert the SoC compatibles description to YAML
> arm64: dts: marvell: Add support for Marvell CN9130 SoC support
All series applied on mvebu/dt64
Thanks,
Gregory
>
> ...roller.txt => ap80x-system-controller.txt} | 14 +-
> .../bindings/arm/marvell/armada-7k-8k.txt | 24 -
> .../bindings/arm/marvell/armada-7k-8k.yaml | 61 ++
> MAINTAINERS | 3 +-
> arch/arm64/boot/dts/marvell/Makefile | 3 +
> arch/arm64/boot/dts/marvell/armada-70x0.dtsi | 28 +-
> .../boot/dts/marvell/armada-8040-mcbin.dtsi | 3 +-
> arch/arm64/boot/dts/marvell/armada-80x0.dtsi | 56 +-
> .../boot/dts/marvell/armada-ap806-dual.dtsi | 23 +
> .../boot/dts/marvell/armada-ap806-quad.dtsi | 42 ++
> arch/arm64/boot/dts/marvell/armada-ap806.dtsi | 456 +-------------
> .../boot/dts/marvell/armada-ap807-quad.dtsi | 93 +++
> arch/arm64/boot/dts/marvell/armada-ap807.dtsi | 29 +
> arch/arm64/boot/dts/marvell/armada-ap80x.dtsi | 444 ++++++++++++++
> .../arm64/boot/dts/marvell/armada-common.dtsi | 4 +-
> arch/arm64/boot/dts/marvell/armada-cp110.dtsi | 575 +-----------------
> arch/arm64/boot/dts/marvell/armada-cp115.dtsi | 12 +
> arch/arm64/boot/dts/marvell/armada-cp11x.dtsi | 568 +++++++++++++++++
> arch/arm64/boot/dts/marvell/cn9130-db.dts | 403 ++++++++++++
> arch/arm64/boot/dts/marvell/cn9130.dtsi | 37 ++
> arch/arm64/boot/dts/marvell/cn9131-db.dts | 202 ++++++
> arch/arm64/boot/dts/marvell/cn9132-db.dts | 221 +++++++
> 22 files changed, 2210 insertions(+), 1091 deletions(-)
> rename Documentation/devicetree/bindings/arm/marvell/{ap806-system-controller.txt => ap80x-system-controller.txt} (91%)
> delete mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt
> create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml
> create mode 100644 arch/arm64/boot/dts/marvell/armada-ap807-quad.dtsi
> create mode 100644 arch/arm64/boot/dts/marvell/armada-ap807.dtsi
> create mode 100644 arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
> create mode 100644 arch/arm64/boot/dts/marvell/armada-cp115.dtsi
> create mode 100644 arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
> create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dts
> create mode 100644 arch/arm64/boot/dts/marvell/cn9130.dtsi
> create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dts
> create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dts
>
> --
> 2.20.1
>
--
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 25+ messages in thread
end of thread, other threads:[~2019-10-08 12:26 UTC | newest]
Thread overview: 25+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-10-04 14:27 [PATCH v2 00/21] Add new Marvell CN9130 SoC support Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 01/21] arm64: dts: marvell: Enumerate the first AP806 syscon Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 02/21] arm64: dts: marvell: Add AP806-dual missing CPU clocks Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 03/21] dt-bindings: ap80x: replace AP806 with AP80x Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 04/21] MAINTAINERS: Add new Marvell CN9130-based files to track Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 05/21] arm64: dts: marvell: Prepare the introduction of AP807 based SoCs Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 06/21] arm64: dts: marvell: Move clocks to AP806 specific file Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 07/21] arm64: dts: marvell: Add support for AP807/AP807-quad Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 08/21] arm64: dts: marvell: Add AP806-dual cache description Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 09/21] arm64: dts: marvell: Add AP806-quad " Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 10/21] arm64: dts: marvell: Add AP807-quad " Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 11/21] arm64: dts: marvell: Fix CP110 NAND controller node multi-line comment alignment Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 12/21] arm64: dts: marvell: Prepare the introduction of CP115 Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 13/21] arm64: dts: marvell: Drop PCIe I/O ranges from CP11x file Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 14/21] arm64: dts: marvell: Externalize PCIe macros " Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 15/21] arm64: dts: marvell: Add support for CP115 Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 16/21] dt-bindings: marvell: Convert the SoC compatibles description to YAML Miquel Raynal
2019-10-04 16:13 ` Rob Herring
2019-10-04 14:27 ` [PATCH v2 17/21] dt-bindings: marvell: Declare the CN913x SoC compatibles Miquel Raynal
2019-10-04 16:14 ` Rob Herring
2019-10-04 14:27 ` [PATCH v2 18/21] arm64: dts: marvell: Add support for Marvell CN9130 SoC support Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 19/21] arm64: dts: marvell: Add support for Marvell CN9130-DB Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 20/21] arm64: dts: marvell: Add support for Marvell CN9131-DB Miquel Raynal
2019-10-04 14:27 ` [PATCH v2 21/21] arm64: dts: marvell: Add support for Marvell CN9132-DB Miquel Raynal
2019-10-08 12:25 ` [PATCH v2 00/21] Add new Marvell CN9130 SoC support Gregory CLEMENT
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).