* [PATCH 1/2] arm64: dts: imx8mq-evk: Adjust nodes following alphabetical sort
@ 2019-10-09 2:34 Anson Huang
2019-10-09 2:34 ` [PATCH 2/2] arm64: dts: imx8mn-ddr4-evk: Move iomuxc node to end of file Anson Huang
2019-10-14 13:33 ` [PATCH 1/2] arm64: dts: imx8mq-evk: Adjust nodes following alphabetical sort Shawn Guo
0 siblings, 2 replies; 3+ messages in thread
From: Anson Huang @ 2019-10-09 2:34 UTC (permalink / raw)
To: robh+dt, mark.rutland, shawnguo, s.hauer, kernel, festevam,
l.stach, ccaione, abel.vesa, daniel.baluta, andrew.smirnov,
devicetree, linux-arm-kernel, linux-kernel
Cc: Linux-imx
Adjust some nodes to make them follow alphabetical sort except
iomuxc node which is put at the end of file because of its huge
pinctrl data.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8mq-evk.dts | 46 ++++++++++++++--------------
1 file changed, 23 insertions(+), 23 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
index 0595812..6ede46f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
@@ -115,15 +115,6 @@
};
};
-&sai2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_sai2>;
- assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1_BYPASS>, <&clk IMX8MQ_CLK_SAI2>;
- assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL1_OUT>;
- assigned-clock-rates = <0>, <24576000>;
- status = "okay";
-};
-
&gpio5 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_wifi_reset>;
@@ -242,6 +233,29 @@
power-supply = <&sw1a_reg>;
};
+&qspi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi>;
+ status = "okay";
+
+ n25q256a: flash@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q256a", "jedec,spi-nor";
+ spi-max-frequency = <29000000>;
+ };
+};
+
+&sai2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai2>;
+ assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1_BYPASS>, <&clk IMX8MQ_CLK_SAI2>;
+ assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL1_OUT>;
+ assigned-clock-rates = <0>, <24576000>;
+ status = "okay";
+};
+
&snvs_pwrkey {
status = "okay";
};
@@ -261,20 +275,6 @@
status = "okay";
};
-&qspi0 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_qspi>;
- status = "okay";
-
- n25q256a: flash@0 {
- reg = <0>;
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "micron,n25q256a", "jedec,spi-nor";
- spi-max-frequency = <29000000>;
- };
-};
-
&usdhc1 {
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc1>;
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH 2/2] arm64: dts: imx8mn-ddr4-evk: Move iomuxc node to end of file
2019-10-09 2:34 [PATCH 1/2] arm64: dts: imx8mq-evk: Adjust nodes following alphabetical sort Anson Huang
@ 2019-10-09 2:34 ` Anson Huang
2019-10-14 13:33 ` [PATCH 1/2] arm64: dts: imx8mq-evk: Adjust nodes following alphabetical sort Shawn Guo
1 sibling, 0 replies; 3+ messages in thread
From: Anson Huang @ 2019-10-09 2:34 UTC (permalink / raw)
To: robh+dt, mark.rutland, shawnguo, s.hauer, kernel, festevam,
l.stach, ccaione, abel.vesa, daniel.baluta, andrew.smirnov,
devicetree, linux-arm-kernel, linux-kernel
Cc: Linux-imx
All nodes are better to follow alphabetical sort except iomuxc
which has huge pinctrl data, better to put it at the end of
file.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts | 304 +++++++++++-----------
1 file changed, 152 insertions(+), 152 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
index d78d657..1b90faac 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
@@ -43,158 +43,6 @@
cpu-supply = <&buck2_reg>;
};
-&iomuxc {
- pinctrl-names = "default";
-
- pinctrl_fec1: fec1grp {
- fsl,pins = <
- MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x3
- MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
- MX8MN_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
- MX8MN_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
- MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
- MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
- MX8MN_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
- MX8MN_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
- MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
- MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
- MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
- MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
- MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
- MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
- MX8MN_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19
- >;
- };
-
- pinctrl_gpio_led: gpioledgrp {
- fsl,pins = <
- MX8MN_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19
- >;
- };
-
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
- MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
- >;
- };
-
- pinctrl_pmic: pmicirq {
- fsl,pins = <
- MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41
- >;
- };
-
- pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
- fsl,pins = <
- MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41
- >;
- };
-
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
- MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
- >;
- };
-
- pinctrl_usdhc2_gpio: usdhc2grpgpio {
- fsl,pins = <
- MX8MN_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x1c4
- >;
- };
-
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
- MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
- MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
- MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
- MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
- MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
- MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
- >;
- };
-
- pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
- fsl,pins = <
- MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
- MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
- MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
- MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
- MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
- MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
- MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
- >;
- };
-
- pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
- fsl,pins = <
- MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
- MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
- MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
- MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
- MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
- MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
- MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
- >;
- };
-
- pinctrl_usdhc3: usdhc3grp {
- fsl,pins = <
- MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x40000190
- MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
- MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
- MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
- MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
- MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
- MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0
- MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0
- MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0
- MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0
- MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190
- >;
- };
-
- pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
- fsl,pins = <
- MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x40000194
- MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
- MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
- MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
- MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
- MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
- MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
- MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
- MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
- MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
- MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194
- >;
- };
-
- pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
- fsl,pins = <
- MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x40000196
- MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
- MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
- MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
- MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
- MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
- MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6
- MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6
- MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6
- MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6
- MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196
- >;
- };
-
- pinctrl_wdog: wdoggrp {
- fsl,pins = <
- MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
- >;
- };
-};
-
&fec1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_fec1>;
@@ -364,3 +212,155 @@
fsl,ext-reset-output;
status = "okay";
};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
+ MX8MN_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MN_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MN_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MN_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ MX8MN_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19
+ >;
+ };
+
+ pinctrl_gpio_led: gpioledgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
+ MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_pmic: pmicirq {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41
+ >;
+ };
+
+ pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
+ MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpio {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x1c4
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x40000190
+ MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
+ MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
+ MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
+ MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
+ MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
+ MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0
+ MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0
+ MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0
+ MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0
+ MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+ fsl,pins = <
+ MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x40000194
+ MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
+ MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+ fsl,pins = <
+ MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x40000196
+ MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
+ MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
+ MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
+ MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
+ MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
+ MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6
+ MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6
+ MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6
+ MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6
+ MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+};
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH 1/2] arm64: dts: imx8mq-evk: Adjust nodes following alphabetical sort
2019-10-09 2:34 [PATCH 1/2] arm64: dts: imx8mq-evk: Adjust nodes following alphabetical sort Anson Huang
2019-10-09 2:34 ` [PATCH 2/2] arm64: dts: imx8mn-ddr4-evk: Move iomuxc node to end of file Anson Huang
@ 2019-10-14 13:33 ` Shawn Guo
1 sibling, 0 replies; 3+ messages in thread
From: Shawn Guo @ 2019-10-14 13:33 UTC (permalink / raw)
To: Anson Huang
Cc: mark.rutland, devicetree, abel.vesa, ccaione, andrew.smirnov,
daniel.baluta, s.hauer, linux-kernel, robh+dt, Linux-imx, kernel,
festevam, linux-arm-kernel, l.stach
On Wed, Oct 09, 2019 at 10:34:38AM +0800, Anson Huang wrote:
> Adjust some nodes to make them follow alphabetical sort except
> iomuxc node which is put at the end of file because of its huge
> pinctrl data.
>
> Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Applied both, thanks.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2019-10-14 13:34 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-10-09 2:34 [PATCH 1/2] arm64: dts: imx8mq-evk: Adjust nodes following alphabetical sort Anson Huang
2019-10-09 2:34 ` [PATCH 2/2] arm64: dts: imx8mn-ddr4-evk: Move iomuxc node to end of file Anson Huang
2019-10-14 13:33 ` [PATCH 1/2] arm64: dts: imx8mq-evk: Adjust nodes following alphabetical sort Shawn Guo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).