* [PATCH v4 2/2] ARM: dts: at91: add smartkiz support and a common kizboxmini dtsi file
2019-12-05 22:50 [PATCH v4 1/2] dt-bindings: arm: at91: Document Kizboxmini and Smartkiz boards binding Kamel Bouhara
@ 2019-12-05 22:50 ` Kamel Bouhara
0 siblings, 0 replies; 2+ messages in thread
From: Kamel Bouhara @ 2019-12-05 22:50 UTC (permalink / raw)
To: Rob Herring, Nicolas Ferre, Alexandre Belloni, Ludovic Desroches,
linux-arm-kernel
Cc: Mickael GARDET, devicetree, Kévin RAYMOND, Thomas Petazzoni,
Kamel Bouhara
Split the existing Kizbox Mini boards into three board configuration,
the base board, the mother board and the RailDIN board.
Add a new dts file for the SmartKiz board support.
Signed-off-by: Kévin RAYMOND <k.raymond@overkiz.com>
Signed-off-by: Mickael GARDET <m.gardet@overkiz.com>
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
---
arch/arm/boot/dts/Makefile | 5 +-
arch/arm/boot/dts/at91-kizboxmini-base.dts | 24 +++
...oxmini.dts => at91-kizboxmini-common.dtsi} | 163 +++++++++---------
arch/arm/boot/dts/at91-kizboxmini-mb.dts | 26 +++
arch/arm/boot/dts/at91-kizboxmini-rd.dts | 49 ++++++
arch/arm/boot/dts/at91-smartkiz.dts | 109 ++++++++++++
6 files changed, 293 insertions(+), 83 deletions(-)
create mode 100644 arch/arm/boot/dts/at91-kizboxmini-base.dts
rename arch/arm/boot/dts/{at91-kizboxmini.dts => at91-kizboxmini-common.dtsi} (51%)
create mode 100644 arch/arm/boot/dts/at91-kizboxmini-mb.dts
create mode 100644 arch/arm/boot/dts/at91-kizboxmini-rd.dts
create mode 100644 arch/arm/boot/dts/at91-smartkiz.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4ac053115a8e..83865d3072b5 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -37,7 +37,10 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
at91-ariag25.dtb \
at91-ariettag25.dtb \
at91-cosino_mega2560.dtb \
- at91-kizboxmini.dtb \
+ at91-kizboxmini-base.dtb \
+ at91-kizboxmini-mb.dtb \
+ at91-kizboxmini-rd.dtb \
+ at91-smartkiz.dtb \
at91-wb45n.dtb \
at91sam9g15ek.dtb \
at91sam9g25ek.dtb \
diff --git a/arch/arm/boot/dts/at91-kizboxmini-base.dts b/arch/arm/boot/dts/at91-kizboxmini-base.dts
new file mode 100644
index 000000000000..81c29ca5cc1b
--- /dev/null
+++ b/arch/arm/boot/dts/at91-kizboxmini-base.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * at91-kizboxmini-base.dts - Device Tree file for Overkiz Kizbox mini
+ * base board
+ *
+ * Copyright (C) 2015 Overkiz SAS
+ * Author: Antoine Aubert <a.aubert@overkiz.com>
+ * Kévin Raymond <k.raymond@overkiz.com>
+ */
+/dts-v1/;
+#include "at91-kizboxmini-common.dtsi"
+
+/ {
+ model = "Overkiz Kizbox Mini";
+ compatible = "overkiz,kizboxmini-base", "atmel,at91sam9g25",
+ "atmel,at91sam9x5", "atmel,at91sam9";
+};
+
+&pinctrl_usart0 {
+ atmel,pins =
+ <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+ AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOA 2 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>;
+};
diff --git a/arch/arm/boot/dts/at91-kizboxmini.dts b/arch/arm/boot/dts/at91-kizboxmini-common.dtsi
similarity index 51%
rename from arch/arm/boot/dts/at91-kizboxmini.dts
rename to arch/arm/boot/dts/at91-kizboxmini-common.dtsi
index cb22f5fb055f..fddf267b2d17 100644
--- a/arch/arm/boot/dts/at91-kizboxmini.dts
+++ b/arch/arm/boot/dts/at91-kizboxmini-common.dtsi
@@ -1,17 +1,16 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
+// SPDX-License-Identifier: GPL-2.0
/*
* at91-kizboxmini.dts - Device Tree file for Overkiz Kizbox mini board
*
- * Copyright (C) 2014 Gaël PORTAY <g.portay@overkiz.com>
+ * Copyright (C) 2014-2018 Overkiz SAS
+ * Author: Antoine Aubert <a.aubert@overkiz.com>
+ * Gaël Portay <g.portay@overkiz.com>
+ * Kévin Raymond <k.raymond@overkiz.com>
+ * Dorian Rocipon <d.rocipon@overkiz.com>
*/
-/dts-v1/;
#include "at91sam9g25.dtsi"
-#include <dt-bindings/pwm/pwm.h>
/ {
- model = "Overkiz Kizbox mini";
- compatible = "overkiz,kizboxmini", "atmel,at91sam9g25", "atmel,at91sam9x5", "atmel,at91sam9";
-
chosen {
bootargs = "ubi.mtd=ubi";
stdout-path = &dbgu;
@@ -22,24 +21,16 @@
};
clocks {
- slow_xtal {
- clock-frequency = <32768>;
- };
-
main_xtal {
clock-frequency = <12000000>;
};
- };
- ahb {
- nand0: nand@40000000 {
- nand-bus-width = <8>;
- nand-ecc-mode = "hw";
- atmel,has-pmecc;
- atmel,pmecc-cap = <4>;
- atmel,pmecc-sector-size = <512>;
- nand-on-flash-bbt;
- status = "okay";
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ adc_op_clk {
+ status = "disabled";
};
};
@@ -63,17 +54,25 @@
};
};
- pwm_leds {
+ leds: pwm_leds {
compatible = "pwm-leds";
- green {
+ led_blue: pwm_blue {
+ label = "pwm:blue:user";
+ pwms = <&pwm0 2 10000000 0>;
+ max-brightness = <255>;
+ linux,default-trigger = "none";
+ status = "disabled";
+ };
+
+ led_green: pwm_green {
label = "pwm:green:user";
pwms = <&pwm0 0 10000000 0>;
max-brightness = <255>;
linux,default-trigger = "default-on";
};
- red {
+ led_red: pwm_red {
label = "pwm:red:user";
pwms = <&pwm0 1 10000000 0>;
max-brightness = <255>;
@@ -82,53 +81,12 @@
};
};
-&dbgu {
+&usart0 {
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
status = "okay";
};
-&ebi {
- pinctrl-0 = <&pinctrl_ebi_addr_nand
- &pinctrl_ebi_data_0_7>;
- pinctrl-names = "default";
- status = "okay";
-
- nand-controller {
- pinctrl-0 = <&pinctrl_nand_oe_we
- &pinctrl_nand_cs
- &pinctrl_nand_rb>;
- pinctrl-names = "default";
- status = "okay";
-
- nand@3 {
- reg = <0x3 0x0 0x800000>;
- rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
- cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
- nand-bus-width = <8>;
- nand-ecc-mode = "hw";
- nand-ecc-strength = <4>;
- nand-ecc-step-size = <512>;
- nand-on-flash-bbt;
- label = "atmel_nand";
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- bootstrap@0 {
- label = "bootstrap";
- reg = <0x0 0x20000>;
- };
-
- ubi@20000 {
- label = "ubi";
- reg = <0x20000 0x7fe0000>;
- };
- };
- };
- };
-};
-
&macb0 {
phy-mode = "rmii";
status = "okay";
@@ -137,26 +95,70 @@
&pwm0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm0_pwm0_1
- &pinctrl_pwm0_pwm1_1>;
+ &pinctrl_pwm0_pwm1_1
+ &pinctrl_pwm0_pwm2_1>;
status = "okay";
};
-&tcb0 {
- timer@0 {
- compatible = "atmel,tcb-timer";
- reg = <0>;
- };
+&dbgu {
+ status = "okay";
+};
- timer@1 {
- compatible = "atmel,tcb-timer";
- reg = <1>;
- };
+&watchdog {
+ status = "okay";
};
-&usart0 {
+&adc0 {
+ status = "disabled";
+};
+
+&rtc {
+ status = "disabled";
+};
+
+&ebi {
+ pinctrl-0 = <&pinctrl_ebi_addr_nand
+ &pinctrl_ebi_data_0_7>;
+ pinctrl-names = "default";
status = "okay";
};
+&nand_controller {
+ status = "okay";
+ pinctrl-0 = <&pinctrl_nand_oe_we
+ &pinctrl_nand_cs
+ &pinctrl_nand_rb>;
+ pinctrl-names = "default";
+
+ nand@3 {
+ reg = <0x3 0x0 0x800000>;
+ rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ nand-on-flash-bbt;
+ label = "atmel_nand";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ bootstrap@0 {
+ label = "bootstrap";
+ reg = <0x0 0x20000>;
+ };
+
+ ubi@20000 {
+ label = "ubi";
+ reg = <0x20000 0x7fe0000>;
+ };
+ };
+ };
+};
+
&usb0 {
num-ports = <1>;
status = "okay";
@@ -166,6 +168,3 @@
status = "okay";
};
-&watchdog {
- status = "okay";
-};
diff --git a/arch/arm/boot/dts/at91-kizboxmini-mb.dts b/arch/arm/boot/dts/at91-kizboxmini-mb.dts
new file mode 100644
index 000000000000..c07d3076a9bc
--- /dev/null
+++ b/arch/arm/boot/dts/at91-kizboxmini-mb.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2015-2018 Overkiz SAS
+ * Author: Mickael Gardet <m.gardet@overkiz.com>
+ * Kévin Raymond <k.raymond@overkiz.com>
+ */
+/dts-v1/;
+#include "at91-kizboxmini-common.dtsi"
+
+/ {
+ model = "Overkiz Kizbox Mini Mother Board";
+ compatible = "overkiz,kizboxmini-mb", "atmel,at91sam9g25",
+ "atmel,at91sam9x5", "atmel,at91sam9";
+};
+
+&usb0 {
+ num-ports = <2>;
+};
+
+&rtc {
+ status = "okay";
+};
+
+&led_blue {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/at91-kizboxmini-rd.dts b/arch/arm/boot/dts/at91-kizboxmini-rd.dts
new file mode 100644
index 000000000000..ab50f4d22387
--- /dev/null
+++ b/arch/arm/boot/dts/at91-kizboxmini-rd.dts
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2015-2018 Overkiz SAS
+ * Author: Mickael Gardet <m.gardet@overkiz.com>
+ * Kévin Raymond <k.raymond@overkiz.com>
+ */
+/dts-v1/;
+#include "at91-kizboxmini-common.dtsi"
+
+/ {
+ model = "Overkiz Kizbox Mini RailDIN";
+ compatible = "overkiz,kizboxmini-rd", "atmel,at91sam9g25",
+ "atmel,at91sam9x5", "atmel,at91sam9";
+
+ clocks {
+ adc_op_clk {
+ status = "okay";
+ };
+ };
+};
+
+&pinctrl {
+ adc0 {
+ pinctrl_adc0_ad5: adc0_ad5-0 {
+ /* pull-up disable */
+ atmel,pins = <AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+};
+
+&usart0 {
+ status = "disabled";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&led_blue {
+ status = "okay";
+};
+
+&adc0 {
+ atmel,adc-vref = <2500>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc0_ad5>;
+ atmel,adc-channels-used = <0x0020>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/at91-smartkiz.dts b/arch/arm/boot/dts/at91-smartkiz.dts
new file mode 100644
index 000000000000..2354385f9685
--- /dev/null
+++ b/arch/arm/boot/dts/at91-smartkiz.dts
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017-2018 Overkiz SAS
+ * Author: Mickael Gardet <m.gardet@overkiz.com>
+ * Kévin Raymond <k.raymond@overkiz.com>
+ * Dorian Rocipon <d.rocipon@overkiz.com>
+ */
+/dts-v1/;
+#include "at91-kizboxmini_common.dtsi"
+
+/ {
+ model = "Overkiz SmartKiz";
+ compatible = "overkiz,smartkiz", "atmel,at91sam9g25",
+ "atmel,at91sam9x5", "atmel,at91sam9";
+
+ clocks {
+ adc_op_clk {
+ status = "okay";
+ };
+ };
+
+ aliases {
+ serial5 = &uart0;
+ };
+
+ pio_keys {
+ hk_reset {
+ label = "HK_RESET";
+ gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
+ };
+
+ power_rf {
+ label = "POWER_RF";
+ gpios = <&pioA 20 GPIO_ACTIVE_HIGH>;
+ };
+
+ power_wifi {
+ label = "POWER_WIFI";
+ gpios = <&pioA 21 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&pinctrl {
+ i2c1 {
+ pinctrl_i2c1: i2c1-0 {
+ atmel,pins =
+ <AT91_PIOC 0 AT91_PERIPH_C AT91_PINCTRL_PULL_UP
+ AT91_PIOC 1 AT91_PERIPH_C AT91_PINCTRL_PULL_UP>;
+ };
+ };
+
+ adc0 {
+ pinctrl_adc0_ad0: adc0_ad0-0 {
+ /* pull-up disable */
+ atmel,pins = <AT91_PIOB 11 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ pinctrl_adc0_ad5: adc0_ad5-0 {
+ /* pull-up disable */
+ atmel,pins = <AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ pinctrl_adc0_ad6: adc0_ad6-0 {
+ /* pull-up disable */
+ atmel,pins = <AT91_PIOB 17 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ pinctrl_adc0_ad11: adc0_ad11-0 {
+ /* pull-up disable */
+ atmel,pins = <AT91_PIOB 10 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+};
+
+&i2c1 {
+ dmas = <0>, <0>;
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "disabled";
+};
+
+&macb0 {
+ status = "disabled";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&leds {
+ blue {
+ status = "okay";
+ };
+};
+
+&adc0 {
+ atmel,adc-vref = <2500>;
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &pinctrl_adc0_ad0
+ &pinctrl_adc0_ad5
+ &pinctrl_adc0_ad6
+ &pinctrl_adc0_ad11
+ >;
+ atmel,adc-channels-used = <0x0861>;
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
--
2.24.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 2+ messages in thread