Re: [PATCH V3 2/3] dt-bindings: pinctrl: Convert i.MX8MM to json-schema

[Marco Felsch <m.felsch@pengutronix.de>]

Hi Anson,

On 20-01-15 09:30, Anson Huang wrote:
> Convert the i.MX8MM pinctrl binding to DT schema format using json-schema
> 
> Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
> ---
> Change since V2:
> 	- the lisence should be GPL-2.0
> ---
>  .../bindings/pinctrl/fsl,imx8mm-pinctrl.txt        | 36 -----------
>  .../bindings/pinctrl/fsl,imx8mm-pinctrl.yaml       | 69 ++++++++++++++++++++++
>  2 files changed, 69 insertions(+), 36 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.yaml
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt
> deleted file mode 100644
> index e4e01c0..0000000
> --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt
> +++ /dev/null
> @@ -1,36 +0,0 @@
> -* Freescale IMX8MM IOMUX Controller
> -
> -Please refer to fsl,imx-pinctrl.txt and pinctrl-bindings.txt in this directory
> -for common binding part and usage.
> -
> -Required properties:
> -- compatible: "fsl,imx8mm-iomuxc"
> -- reg: should contain the base physical address and size of the iomuxc
> -  registers.
> -
> -Required properties in sub-nodes:
> -- fsl,pins: each entry consists of 6 integers and represents the mux and config
> -  setting for one pin.  The first 5 integers <mux_reg conf_reg input_reg mux_val
> -  input_val> are specified using a PIN_FUNC_ID macro, which can be found in
> -  <arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h>. The last integer CONFIG is
> -  the pad setting value like pull-up on this pin.  Please refer to i.MX8M Mini
> -  Reference Manual for detailed CONFIG settings.
> -
> -Examples:
> -
> -&uart1 {
> -       pinctrl-names = "default";
> -       pinctrl-0 = <&pinctrl_uart1>;
> -};
> -
> -iomuxc: pinctrl@30330000 {
> -        compatible = "fsl,imx8mm-iomuxc";
> -        reg = <0x0 0x30330000 0x0 0x10000>;
> -
> -        pinctrl_uart1: uart1grp {
> -                fsl,pins = <
> -                        MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX             0x140
> -                        MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX             0x140
> -                >;
> -        };
> -};
> diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.yaml
> new file mode 100644
> index 0000000..8b2de93
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.yaml
> @@ -0,0 +1,69 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/fsl,imx8mm-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Freescale IMX8MM IOMUX Controller
> +
> +maintainers:
> +  - Anson Huang <Anson.Huang@nxp.com>
> +
> +description:
> +  Please refer to fsl,imx-pinctrl.txt and pinctrl-bindings.txt in this directory
> +  for common binding part and usage.
> +
> +properties:
> +  compatible:
> +    const: fsl,imx8mm-iomuxc
> +
> +  reg:
> +    maxItems: 1
> +
> +# Client device subnode's properties
> +patternProperties:
> +  'grp$':
> +    type: object
> +    description:
> +      Pinctrl node's client devices use subnodes for desired pin configuration.
> +      Client device subnodes use below standard properties.
> +
> +    properties:
> +      fsl,pins:
> +        allOf:
> +          - $ref: /schemas/types.yaml#/definitions/uint32-array
> +        description:
> +          each entry consists of 6 integers and represents the mux and config
> +          setting for one pin. The first 5 integers <mux_reg conf_reg input_reg
> +          mux_val input_val> are specified using a PIN_FUNC_ID macro, which can
> +          be found in <arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h>. The last
> +          integer CONFIG is the pad setting value like pull-up on this pin. Please
> +          refer to i.MX8M Mini Reference Manual for detailed CONFIG settings.
> +
> +    required:
> +      - fsl,pins
> +
> +    additionalProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +
> +additionalProperties: false
> +
> +examples:
> +  # Pinmux controller node
> +  - |
> +    iomuxc: pinctrl@30330000 {
> +        compatible = "fsl,imx8mm-iomuxc";
> +        reg = <0x30330000 0x10000>;
> +
> +        pinctrl_uart2: uart2grp {
> +            fsl,pins = <
> +                0x23C 0x4A4 0x4FC 0x0 0x0	0x140

Why we can't use the pinctrl defines like
MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX anymore?

Regards,
  Marco

> +                0x240 0x4A8 0x000 0x0 0x0	0x140
> +            >;
> +        };
> +    };
> +
> +...
> -- 
> 2.7.4
> 
> 
> 

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel