* [PATCH 1/3] arm64: dts: rockchip: add core devicetree for rk3326
@ 2020-03-06 21:09 Heiko Stuebner
2020-03-06 21:09 ` [PATCH 2/3] dt-bindings: Add binding for Hardkernel Odroid Go Advance Heiko Stuebner
2020-03-06 21:09 ` [PATCH 3/3] arm64: dts: rockchip: add Odroid Advance Go Heiko Stuebner
0 siblings, 2 replies; 5+ messages in thread
From: Heiko Stuebner @ 2020-03-06 21:09 UTC (permalink / raw)
To: linux-rockchip
Cc: mark.rutland, devicetree, heiko, Heiko Stuebner, kever.yang,
robh+dt, robin.murphy, linux-arm-kernel, christoph.muellner
From: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
The rk3326 is basically a px30 without the second display controller.
So add a dtsi based on that, that just removes the affected nodes.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
---
arch/arm64/boot/dts/rockchip/rk3326.dtsi | 15 +++++++++++++++
1 file changed, 15 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3326.dtsi
diff --git a/arch/arm64/boot/dts/rockchip/rk3326.dtsi b/arch/arm64/boot/dts/rockchip/rk3326.dtsi
new file mode 100644
index 000000000000..2ba6da125137
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3326.dtsi
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Fuzhou Rockchip Electronics Co., Ltd
+ */
+
+#include "px30.dtsi"
+
+&display_subsystem {
+ ports = <&vopb_out>;
+};
+
+/delete-node/ &dsi_in_vopl;
+/delete-node/ &lvds_vopl_in;
+/delete-node/ &vopl;
+/delete-node/ &vopl_mmu;
--
2.24.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 2/3] dt-bindings: Add binding for Hardkernel Odroid Go Advance
2020-03-06 21:09 [PATCH 1/3] arm64: dts: rockchip: add core devicetree for rk3326 Heiko Stuebner
@ 2020-03-06 21:09 ` Heiko Stuebner
2020-03-06 21:09 ` [PATCH 3/3] arm64: dts: rockchip: add Odroid Advance Go Heiko Stuebner
1 sibling, 0 replies; 5+ messages in thread
From: Heiko Stuebner @ 2020-03-06 21:09 UTC (permalink / raw)
To: linux-rockchip
Cc: mark.rutland, devicetree, heiko, Heiko Stuebner, kever.yang,
robh+dt, robin.murphy, linux-arm-kernel, christoph.muellner
From: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Add a compatible for the Odroid Go Advance from Hardkernel.
The compatible used by the vendor already is odroid-go2, to distinguish
it from the previous (microcontroller-based) Odroid Go, so we're keeping
that, also to not cause unnecessary incompatibilites.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
---
Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index f4ba00d679e6..4343ce7880e4 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -358,6 +358,11 @@ properties:
- const: haoyu,marsboard-rk3066
- const: rockchip,rk3066a
+ - description: Hardkernel Odroid Go Advance
+ items:
+ - const: hardkernel,rk3326-odroid-go2
+ - const: rockchip,rk3326
+
- description: Hugsun X99 TV Box
items:
- const: hugsun,x99
--
2.24.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 3/3] arm64: dts: rockchip: add Odroid Advance Go
2020-03-06 21:09 [PATCH 1/3] arm64: dts: rockchip: add core devicetree for rk3326 Heiko Stuebner
2020-03-06 21:09 ` [PATCH 2/3] dt-bindings: Add binding for Hardkernel Odroid Go Advance Heiko Stuebner
@ 2020-03-06 21:09 ` Heiko Stuebner
2020-03-07 8:36 ` Johan Jonker
1 sibling, 1 reply; 5+ messages in thread
From: Heiko Stuebner @ 2020-03-06 21:09 UTC (permalink / raw)
To: linux-rockchip
Cc: mark.rutland, devicetree, heiko, Heiko Stuebner, kever.yang,
robh+dt, robin.murphy, linux-arm-kernel, christoph.muellner
From: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
The Odroid Advance Go is a handheld based on Rockchip's rk3326 soc
with a DSI display and some handheld controls including an analog
joystick connected to the saradc.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3326-odroid-go2.dts | 544 ++++++++++++++++++
2 files changed, 545 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index af1e1c3707d0..86c38467d487 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -6,6 +6,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-copperhead-ltk101b4029w.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-odroid-go2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts b/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
new file mode 100644
index 000000000000..a16f4a0d1d4d
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
@@ -0,0 +1,544 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Hardkernel Co., Ltd
+ * Copyright (c) 2020 Theobroma Systems Design und Consulting GmbH
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3326.dtsi"
+
+/ {
+ model = "ODROID-GO Advance";
+ compatible = "hardkernel,rk3326-odroid-go2", "rockchip,rk3326";
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&btn_pins>;
+
+ /*
+ * *** ODROIDGO2-Advance Switch layoout ***
+ * |------------------------------------------------|
+ * | sw15 sw16 |
+ * |------------------------------------------------|
+ * | sw1 |-------------------| sw8 |
+ * | sw3 sw4 | | sw7 sw5 |
+ * | sw2 | LCD Display | sw6 |
+ * | | | |
+ * | |-------------------| |
+ * | sw9 sw10 sw11 sw12 sw13 sw14 |
+ * |------------------------------------------------|
+ */
+
+ sw1 {
+ gpios = <&gpio1 RK_PB4 GPIO_ACTIVE_LOW>;
+ label = "DPAD-UP";
+ linux,code = <BTN_DPAD_UP>;
+ };
+ sw2 {
+ gpios = <&gpio1 RK_PB5 GPIO_ACTIVE_LOW>;
+ label = "DPAD-DOWN";
+ linux,code = <BTN_DPAD_DOWN>;
+ };
+ sw3 {
+ gpios = <&gpio1 RK_PB6 GPIO_ACTIVE_LOW>;
+ label = "DPAD-LEFT";
+ linux,code = <BTN_DPAD_LEFT>;
+ };
+ sw4 {
+ gpios = <&gpio1 RK_PB7 GPIO_ACTIVE_LOW>;
+ label = "DPAD-RIGHT";
+ linux,code = <BTN_DPAD_RIGHT>;
+ };
+ sw5 {
+ gpios = <&gpio1 RK_PA2 GPIO_ACTIVE_LOW>;
+ label = "BTN-A";
+ linux,code = <BTN_EAST>;
+ };
+ sw6 {
+ gpios = <&gpio1 RK_PA5 GPIO_ACTIVE_LOW>;
+ label = "BTN-B";
+ linux,code = <BTN_SOUTH>;
+ };
+ sw7 {
+ gpios = <&gpio1 RK_PA6 GPIO_ACTIVE_LOW>;
+ label = "BTN-Y";
+ linux,code = <BTN_WEST>;
+ };
+ sw8 {
+ gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_LOW>;
+ label = "BTN-X";
+ linux,code = <BTN_NORTH>;
+ };
+ sw9 {
+ gpios = <&gpio2 RK_PA0 GPIO_ACTIVE_LOW>;
+ label = "F1";
+ linux,code = <BTN_TRIGGER_HAPPY1>;
+ };
+ sw10 {
+ gpios = <&gpio2 RK_PA1 GPIO_ACTIVE_LOW>;
+ label = "F2";
+ linux,code = <BTN_TRIGGER_HAPPY2>;
+ };
+ sw11 {
+ gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_LOW>;
+ label = "F3";
+ linux,code = <BTN_TRIGGER_HAPPY3>;
+ };
+ sw12 {
+ gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_LOW>;
+ label = "F4";
+ linux,code = <BTN_TRIGGER_HAPPY4>;
+ };
+ sw13 {
+ gpios = <&gpio2 RK_PA4 GPIO_ACTIVE_LOW>;
+ label = "F5";
+ linux,code = <BTN_TRIGGER_HAPPY5>;
+ };
+ sw14 {
+ gpios = <&gpio2 RK_PA5 GPIO_ACTIVE_LOW>;
+ label = "F6";
+ linux,code = <BTN_TRIGGER_HAPPY6>;
+ };
+ sw15 {
+ gpios = <&gpio2 RK_PA6 GPIO_ACTIVE_LOW>;
+ label = "TOP-LEFT";
+ linux,code = <BTN_TL>;
+ };
+ sw16 {
+ gpios = <&gpio2 RK_PA7 GPIO_ACTIVE_LOW>;
+ label = "TOP-RIGHT";
+ linux,code = <BTN_TR>;
+ };
+ };
+
+ leds: gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "led_pins";
+ pinctrl-0 = <&led_pins>;
+
+ /* Blue LED : GPIO0_C1 */
+ heartbeat {
+ label = "blue:heartbeat";
+ gpios = <&gpio0 RK_PC1 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ power-supply = <&vcc_bl>;
+ pwms = <&pwm1 0 25000 0>;
+ };
+
+ vccsys: vccsys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v8_sys";
+ regulator-always-on;
+ regulator-min-microvolt = <3800000>;
+ regulator-max-microvolt = <3800000>;
+ };
+
+ vcc_host: vcc_host {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_host";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ gpio = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ vin-supply = <&vccsys>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cru {
+ assigned-clocks = <&cru PLL_NPLL>,
+ <&cru ACLK_BUS_PRE>, <&cru ACLK_PERI_PRE>,
+ <&cru HCLK_BUS_PRE>, <&cru HCLK_PERI_PRE>,
+ <&cru PCLK_BUS_PRE>, <&cru SCLK_GPU>,
+ <&cru PLL_CPLL>;
+
+ assigned-clock-rates = <1188000000>,
+ <200000000>, <200000000>,
+ <150000000>, <150000000>,
+ <100000000>, <200000000>,
+ <17000000>;
+};
+
+&display_subsystem {
+ status = "okay";
+};
+
+&dsi {
+ status = "okay";
+
+ ports {
+ mipi_out: port@1 {
+ reg = <1>;
+
+ mipi_out_panel: endpoint {
+ remote-endpoint = <&mipi_in_panel>;
+ };
+ };
+ };
+
+ panel@0 {
+ compatible = "elida,kd35t133";
+ reg = <0>;
+ backlight = <&backlight>;
+ iovcc-supply = <&vcc_lcd>;
+ reset-gpios = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>;
+ vdd-supply = <&vcc_lcd>;
+
+ port {
+ mipi_in_panel: endpoint {
+ remote-endpoint = <&mipi_out_panel>;
+ };
+ };
+ };
+};
+
+&dsi_dphy {
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_logic>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+ i2c-scl-rising-time-ns = <280>;
+ i2c-scl-falling-time-ns = <16>;
+
+ rk817: pmic@20 {
+ compatible = "rockchip,rk817";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PB2 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int>;
+ rockchip,system-power-controller;
+ wakeup-source;
+ #clock-cells = <1>;
+ clock-output-names = "rk808-clkout1", "xin32k";
+
+ vcc1-supply = <&vccsys>;
+ vcc2-supply = <&vccsys>;
+ vcc3-supply = <&vccsys>;
+ vcc4-supply = <&vccsys>;
+ vcc5-supply = <&vccsys>;
+ vcc6-supply = <&vccsys>;
+ vcc7-supply = <&vccsys>;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-ramp-delay = <6001>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <950000>;
+ };
+ };
+
+ vdd_arm: DCDC_REG2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <950000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_3v3: DCDC_REG4 {
+ regulator-name = "vcc_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_1v8: LDO_REG2 {
+ regulator-name = "vcc_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_1v0: LDO_REG3 {
+ regulator-name = "vdd_1v0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG4 {
+ regulator-name = "vcc3v3_pmu";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-name = "vccio_sd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_sd: LDO_REG6 {
+ regulator-name = "vcc_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_bl: LDO_REG7 {
+ regulator-name = "vcc_bl";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_lcd: LDO_REG8 {
+ regulator-name = "vcc_lcd";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <2800000>;
+ };
+ };
+
+ vcc_cam: LDO_REG9 {
+ regulator-name = "vcc_cam";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <3000000>;
+ };
+ };
+ };
+ };
+};
+
+/* EXT Header(P2) : 7(SCL:GPIO0.C2), 8(SDA:GPIO0.C3) */
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+};
+
+/* I2S 1 Channel Used */
+&i2s1_2ch {
+ status = "okay";
+ #sound-dai-cells = <0>;
+};
+
+&io_domains {
+ vccio1-supply = <&vcc_3v3>;
+ vccio2-supply = <&vccio_sd>;
+ vccio3-supply = <&vcc_3v3>;
+ vccio4-supply = <&vcc_3v3>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&pmu_io_domains {
+ pmuio1-supply = <&vcc3v3_pmu>;
+ pmuio2-supply = <&vcc3v3_pmu>;
+ status = "okay";
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ card-detect-delay = <800>;
+ cd-gpios = <&gpio0 RK_PA3 GPIO_ACTIVE_LOW>;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&tsadc {
+ pinctrl-names = "gpio", "otpout";
+ pinctrl-0 = <&tsadc_otp_gpio>;
+ pinctrl-1 = <&tsadc_otp_out>;
+ status = "okay";
+};
+
+&u2phy {
+ status = "okay";
+
+ u2phy_host: host-port {
+ status = "okay";
+ };
+
+ u2phy_otg: otg-port {
+ status = "disabled";
+ };
+};
+
+&usb20_otg {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_xfer &uart1_cts>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2m1_xfer>;
+ status = "okay";
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&pinctrl {
+ pmic {
+ pmic_int: pmic-int {
+ rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ dc_det: dc-det {
+ rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ led_pins: led-pins {
+ rockchip,pins = <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ btns {
+ btn_pins: btn-pins {
+ rockchip,pins = <1 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>,
+ <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>,
+ <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up>,
+ <1 RK_PB7 RK_FUNC_GPIO &pcfg_pull_up>,
+ <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>,
+ <1 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>,
+ <1 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
+ <1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>,
+
+ <2 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>,
+ <2 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>,
+ <2 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>,
+ <2 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>,
+ <2 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>,
+ <2 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>,
+ <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
+ <2 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
--
2.24.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH 3/3] arm64: dts: rockchip: add Odroid Advance Go
2020-03-06 21:09 ` [PATCH 3/3] arm64: dts: rockchip: add Odroid Advance Go Heiko Stuebner
@ 2020-03-07 8:36 ` Johan Jonker
2020-03-07 13:47 ` Heiko Stübner
0 siblings, 1 reply; 5+ messages in thread
From: Johan Jonker @ 2020-03-07 8:36 UTC (permalink / raw)
To: heiko
Cc: mark.rutland, devicetree, heiko.stuebner, kever.yang,
linux-rockchip, robh+dt, robin.murphy, linux-arm-kernel,
christoph.muellner
Hi Heiko,
The 'heartbeat' led seems to need some changes. The rest is inherited
from px30.dtsi I think. How do you deal with all the compatible
properties names that are normally SoC specific?
Also include all mail lists found with:
./scripts/get_maintainer.pl --nogit-fallback --nogit
linux-kernel@vger.kernel.org
DTC arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dtb
DTC arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml
CHECK arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml
arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: tsadc:
tsadc-otp-gpio: {'rockchip,pins': [[0, 6, 0, 123]], 'phandle': [[90]]}
is not of type 'array'
arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: usb@ff340000:
'clock-names', 'power-domains' do not match any of the regexes:
'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: usb@ff300000:
'power-domains' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: usb@ff350000:
'clock-names', 'power-domains' do not match any of the regexes:
'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: gpio-leds:
'heartbeat' does not match any of the regexes: '(^led-[0-9a-f]$|led)',
'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: usb2-phy@100:
'#phy-cells' is a required property
> From: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
>
> The Odroid Advance Go is a handheld based on Rockchip's rk3326 soc
> with a DSI display and some handheld controls including an analog
> joystick connected to the saradc.
>
> Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3326-odroid-go2.dts | 544 ++++++++++++++++++
> 2 files changed, 545 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index af1e1c3707d0..86c38467d487 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -6,6 +6,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-copperhead-ltk101b4029w.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-odroid-go2.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts b/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
> new file mode 100644
> index 000000000000..a16f4a0d1d4d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
> @@ -0,0 +1,544 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2019 Hardkernel Co., Ltd
> + * Copyright (c) 2020 Theobroma Systems Design und Consulting GmbH
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include "rk3326.dtsi"
> +
> +/ {
> + model = "ODROID-GO Advance";
> + compatible = "hardkernel,rk3326-odroid-go2", "rockchip,rk3326";
> +
> + chosen {
> + stdout-path = "serial2:115200n8";
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&btn_pins>;
> +
> + /*
> + * *** ODROIDGO2-Advance Switch layoout ***
> + * |------------------------------------------------|
> + * | sw15 sw16 |
> + * |------------------------------------------------|
> + * | sw1 |-------------------| sw8 |
> + * | sw3 sw4 | | sw7 sw5 |
> + * | sw2 | LCD Display | sw6 |
> + * | | | |
> + * | |-------------------| |
> + * | sw9 sw10 sw11 sw12 sw13 sw14 |
> + * |------------------------------------------------|
> + */
> +
> + sw1 {
> + gpios = <&gpio1 RK_PB4 GPIO_ACTIVE_LOW>;
> + label = "DPAD-UP";
> + linux,code = <BTN_DPAD_UP>;
> + };
> + sw2 {
> + gpios = <&gpio1 RK_PB5 GPIO_ACTIVE_LOW>;
> + label = "DPAD-DOWN";
> + linux,code = <BTN_DPAD_DOWN>;
> + };
> + sw3 {
> + gpios = <&gpio1 RK_PB6 GPIO_ACTIVE_LOW>;
> + label = "DPAD-LEFT";
> + linux,code = <BTN_DPAD_LEFT>;
> + };
> + sw4 {
> + gpios = <&gpio1 RK_PB7 GPIO_ACTIVE_LOW>;
> + label = "DPAD-RIGHT";
> + linux,code = <BTN_DPAD_RIGHT>;
> + };
> + sw5 {
> + gpios = <&gpio1 RK_PA2 GPIO_ACTIVE_LOW>;
> + label = "BTN-A";
> + linux,code = <BTN_EAST>;
> + };
> + sw6 {
> + gpios = <&gpio1 RK_PA5 GPIO_ACTIVE_LOW>;
> + label = "BTN-B";
> + linux,code = <BTN_SOUTH>;
> + };
> + sw7 {
> + gpios = <&gpio1 RK_PA6 GPIO_ACTIVE_LOW>;
> + label = "BTN-Y";
> + linux,code = <BTN_WEST>;
> + };
> + sw8 {
> + gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_LOW>;
> + label = "BTN-X";
> + linux,code = <BTN_NORTH>;
> + };
> + sw9 {
> + gpios = <&gpio2 RK_PA0 GPIO_ACTIVE_LOW>;
> + label = "F1";
> + linux,code = <BTN_TRIGGER_HAPPY1>;
> + };
> + sw10 {
> + gpios = <&gpio2 RK_PA1 GPIO_ACTIVE_LOW>;
> + label = "F2";
> + linux,code = <BTN_TRIGGER_HAPPY2>;
> + };
> + sw11 {
> + gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_LOW>;
> + label = "F3";
> + linux,code = <BTN_TRIGGER_HAPPY3>;
> + };
> + sw12 {
> + gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_LOW>;
> + label = "F4";
> + linux,code = <BTN_TRIGGER_HAPPY4>;
> + };
> + sw13 {
> + gpios = <&gpio2 RK_PA4 GPIO_ACTIVE_LOW>;
> + label = "F5";
> + linux,code = <BTN_TRIGGER_HAPPY5>;
> + };
> + sw14 {
> + gpios = <&gpio2 RK_PA5 GPIO_ACTIVE_LOW>;
> + label = "F6";
> + linux,code = <BTN_TRIGGER_HAPPY6>;
> + };
> + sw15 {
> + gpios = <&gpio2 RK_PA6 GPIO_ACTIVE_LOW>;
> + label = "TOP-LEFT";
> + linux,code = <BTN_TL>;
> + };
> + sw16 {
> + gpios = <&gpio2 RK_PA7 GPIO_ACTIVE_LOW>;
> + label = "TOP-RIGHT";
> + linux,code = <BTN_TR>;
> + };
> + };
> +
> + leds: gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "led_pins";
> + pinctrl-0 = <&led_pins>;
> +
> + /* Blue LED : GPIO0_C1 */
> + heartbeat {
> + label = "blue:heartbeat";
> + gpios = <&gpio0 RK_PC1 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + power-supply = <&vcc_bl>;
> + pwms = <&pwm1 0 25000 0>;
> + };
sort nodenames
> +
> + vccsys: vccsys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v8_sys";
> + regulator-always-on;
> + regulator-min-microvolt = <3800000>;
> + regulator-max-microvolt = <3800000>;
> + };
> +
> + vcc_host: vcc_host {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_host";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> +
> + gpio = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + vin-supply = <&vccsys>;
> + };
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu2 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu3 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cru {
> + assigned-clocks = <&cru PLL_NPLL>,
> + <&cru ACLK_BUS_PRE>, <&cru ACLK_PERI_PRE>,
> + <&cru HCLK_BUS_PRE>, <&cru HCLK_PERI_PRE>,
> + <&cru PCLK_BUS_PRE>, <&cru SCLK_GPU>,
> + <&cru PLL_CPLL>;
> +
> + assigned-clock-rates = <1188000000>,
> + <200000000>, <200000000>,
> + <150000000>, <150000000>,
> + <100000000>, <200000000>,
> + <17000000>;
> +};
> +
> +&display_subsystem {
> + status = "okay";
> +};
> +
> +&dsi {
> + status = "okay";
> +
> + ports {
> + mipi_out: port@1 {
> + reg = <1>;
> +
> + mipi_out_panel: endpoint {
> + remote-endpoint = <&mipi_in_panel>;
> + };
> + };
> + };
> +
> + panel@0 {
> + compatible = "elida,kd35t133";
> + reg = <0>;
> + backlight = <&backlight>;
> + iovcc-supply = <&vcc_lcd>;
> + reset-gpios = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>;
> + vdd-supply = <&vcc_lcd>;
> +
> + port {
> + mipi_in_panel: endpoint {
> + remote-endpoint = <&mipi_out_panel>;
> + };
> + };
> + };
> +};
> +
> +&dsi_dphy {
> + status = "okay";
> +};
> +
> +&gpu {
> + mali-supply = <&vdd_logic>;
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
status below
> + clock-frequency = <400000>;
> + i2c-scl-rising-time-ns = <280>;
> + i2c-scl-falling-time-ns = <16>;
sort
> +
> + rk817: pmic@20 {
> + compatible = "rockchip,rk817";
> + reg = <0x20>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PB2 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int>;
> + rockchip,system-power-controller;
> + wakeup-source;
> + #clock-cells = <1>;
> + clock-output-names = "rk808-clkout1", "xin32k";
> +
> + vcc1-supply = <&vccsys>;
> + vcc2-supply = <&vccsys>;
> + vcc3-supply = <&vccsys>;
> + vcc4-supply = <&vccsys>;
> + vcc5-supply = <&vccsys>;
> + vcc6-supply = <&vccsys>;
> + vcc7-supply = <&vccsys>;
> +
> + regulators {
> + vdd_logic: DCDC_REG1 {
> + regulator-name = "vdd_logic";
> + regulator-min-microvolt = <950000>;
> + regulator-max-microvolt = <1150000>;
> + regulator-ramp-delay = <6001>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <950000>;
> + };
> + };
> +
> + vdd_arm: DCDC_REG2 {
> + regulator-name = "vdd_arm";
> + regulator-min-microvolt = <950000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <950000>;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-name = "vcc_ddr";
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_3v3: DCDC_REG4 {
> + regulator-name = "vcc_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc_1v8: LDO_REG2 {
> + regulator-name = "vcc_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vdd_1v0: LDO_REG3 {
> + regulator-name = "vdd_1v0";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc3v3_pmu: LDO_REG4 {
> + regulator-name = "vcc3v3_pmu";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vccio_sd: LDO_REG5 {
> + regulator-name = "vccio_sd";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc_sd: LDO_REG6 {
> + regulator-name = "vcc_sd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc_bl: LDO_REG7 {
> + regulator-name = "vcc_bl";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc_lcd: LDO_REG8 {
> + regulator-name = "vcc_lcd";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <2800000>;
> + };
> + };
> +
> + vcc_cam: LDO_REG9 {
> + regulator-name = "vcc_cam";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <3000000>;
> + };
> + };
> + };
> + };
> +};
> +
> +/* EXT Header(P2) : 7(SCL:GPIO0.C2), 8(SDA:GPIO0.C3) */
> +&i2c1 {
> + status = "okay";
status below
> + clock-frequency = <400000>;
> +};
> +
> +/* I2S 1 Channel Used */
> +&i2s1_2ch {
> + status = "okay";
status below
> + #sound-dai-cells = <0>;
> +};
> +
> +&io_domains {
> + vccio1-supply = <&vcc_3v3>;
> + vccio2-supply = <&vccio_sd>;
> + vccio3-supply = <&vcc_3v3>;
> + vccio4-supply = <&vcc_3v3>;
> + vccio5-supply = <&vcc_3v3>;
> + vccio6-supply = <&vcc_3v3>;
> + status = "okay";
> +};
> +
> +&pmu_io_domains {
> + pmuio1-supply = <&vcc3v3_pmu>;
> + pmuio2-supply = <&vcc3v3_pmu>;
> + status = "okay";
> +};
> +
> +&pwm1 {
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> +
> +&sdmmc {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + card-detect-delay = <800>;
Other dts use 200. Why we need 800?
> + cd-gpios = <&gpio0 RK_PA3 GPIO_ACTIVE_LOW>;
> + sd-uhs-sdr12;
> + sd-uhs-sdr25;
> + sd-uhs-sdr50;
> + sd-uhs-sdr104;
> + vmmc-supply = <&vcc_sd>;
> + vqmmc-supply = <&vccio_sd>;
> + status = "okay";
> +};
> +
> +&tsadc {
> + pinctrl-names = "gpio", "otpout";
> + pinctrl-0 = <&tsadc_otp_gpio>;
> + pinctrl-1 = <&tsadc_otp_out>;
> + status = "okay";
> +};
> +
> +&u2phy {
> + status = "okay";
> +
> + u2phy_host: host-port {
> + status = "okay";
> + };
> +
> + u2phy_otg: otg-port {
> + status = "disabled";
> + };
> +};
> +
> +&usb20_otg {
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart1_xfer &uart1_cts>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart2m1_xfer>;
> + status = "okay";
> +};
> +
> +&vopb {
> + status = "okay";
> +};
> +
> +&vopb_mmu {
> + status = "okay";
> +};
> +
> +&pinctrl {
> + pmic {
> + pmic_int: pmic-int {
> + rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + dc_det: dc-det {
> + rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + leds {
> + led_pins: led-pins {
> + rockchip,pins = <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + btns {
> + btn_pins: btn-pins {
> + rockchip,pins = <1 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>,
> + <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>,
> + <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up>,
> + <1 RK_PB7 RK_FUNC_GPIO &pcfg_pull_up>,
> + <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>,
> + <1 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>,
> + <1 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
> + <1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>,
> +
> + <2 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>,
> + <2 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>,
> + <2 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>,
> + <2 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>,
> + <2 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>,
> + <2 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>,
> + <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
> + <2 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +};
> --
> 2.24.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH 3/3] arm64: dts: rockchip: add Odroid Advance Go
2020-03-07 8:36 ` Johan Jonker
@ 2020-03-07 13:47 ` Heiko Stübner
0 siblings, 0 replies; 5+ messages in thread
From: Heiko Stübner @ 2020-03-07 13:47 UTC (permalink / raw)
To: Johan Jonker
Cc: mark.rutland, devicetree, kever.yang, linux-rockchip, robh+dt,
robin.murphy, linux-arm-kernel, christoph.muellner
Hi Johan,
Am Samstag, 7. März 2020, 09:36:19 CET schrieb Johan Jonker:
> The 'heartbeat' led seems to need some changes. The rest is inherited
> from px30.dtsi I think. How do you deal with all the compatible
> properties names that are normally SoC specific?
The rk3326 really is just a px30 with the little vop deactivated.
So I really don't want to make "much fuss" over that ;-)
Previous iterations where the arm32 px3/px3se/etc which essentially
also just copied an existing soc and added some industrial voodoo
to the chip itself (temperature range or whatever).
And thanks for making sure the details are right below. I'll do a
v2 with these things corrected.
Thanks
Heiko
> Also include all mail lists found with:
> ./scripts/get_maintainer.pl --nogit-fallback --nogit
>
> linux-kernel@vger.kernel.org
>
> DTC arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dtb
> DTC arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml
> CHECK arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml
> arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: tsadc:
> tsadc-otp-gpio: {'rockchip,pins': [[0, 6, 0, 123]], 'phandle': [[90]]}
> is not of type 'array'
> arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: usb@ff340000:
> 'clock-names', 'power-domains' do not match any of the regexes:
> 'pinctrl-[0-9]+'
> arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: usb@ff300000:
> 'power-domains' does not match any of the regexes: 'pinctrl-[0-9]+'
> arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: usb@ff350000:
> 'clock-names', 'power-domains' do not match any of the regexes:
> 'pinctrl-[0-9]+'
> arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: gpio-leds:
> 'heartbeat' does not match any of the regexes: '(^led-[0-9a-f]$|led)',
> 'pinctrl-[0-9]+'
> arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: usb2-phy@100:
> '#phy-cells' is a required property
>
> > From: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
> >
> > The Odroid Advance Go is a handheld based on Rockchip's rk3326 soc
> > with a DSI display and some handheld controls including an analog
> > joystick connected to the saradc.
> >
> > Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
> > ---
> > arch/arm64/boot/dts/rockchip/Makefile | 1 +
> > .../boot/dts/rockchip/rk3326-odroid-go2.dts | 544 ++++++++++++++++++
> > 2 files changed, 545 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
> >
> > diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> > index af1e1c3707d0..86c38467d487 100644
> > --- a/arch/arm64/boot/dts/rockchip/Makefile
> > +++ b/arch/arm64/boot/dts/rockchip/Makefile
> > @@ -6,6 +6,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-copperhead-ltk101b4029w.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
> > +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-odroid-go2.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
> > diff --git a/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts b/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
> > new file mode 100644
> > index 000000000000..a16f4a0d1d4d
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
> > @@ -0,0 +1,544 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Copyright (c) 2019 Hardkernel Co., Ltd
> > + * Copyright (c) 2020 Theobroma Systems Design und Consulting GmbH
> > + */
> > +
> > +/dts-v1/;
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +#include <dt-bindings/pinctrl/rockchip.h>
> > +#include "rk3326.dtsi"
> > +
> > +/ {
> > + model = "ODROID-GO Advance";
> > + compatible = "hardkernel,rk3326-odroid-go2", "rockchip,rk3326";
> > +
> > + chosen {
> > + stdout-path = "serial2:115200n8";
> > + };
> > +
> > + gpio-keys {
> > + compatible = "gpio-keys";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&btn_pins>;
> > +
> > + /*
> > + * *** ODROIDGO2-Advance Switch layoout ***
> > + * |------------------------------------------------|
> > + * | sw15 sw16 |
> > + * |------------------------------------------------|
> > + * | sw1 |-------------------| sw8 |
> > + * | sw3 sw4 | | sw7 sw5 |
> > + * | sw2 | LCD Display | sw6 |
> > + * | | | |
> > + * | |-------------------| |
> > + * | sw9 sw10 sw11 sw12 sw13 sw14 |
> > + * |------------------------------------------------|
> > + */
> > +
> > + sw1 {
> > + gpios = <&gpio1 RK_PB4 GPIO_ACTIVE_LOW>;
> > + label = "DPAD-UP";
> > + linux,code = <BTN_DPAD_UP>;
> > + };
> > + sw2 {
> > + gpios = <&gpio1 RK_PB5 GPIO_ACTIVE_LOW>;
> > + label = "DPAD-DOWN";
> > + linux,code = <BTN_DPAD_DOWN>;
> > + };
> > + sw3 {
> > + gpios = <&gpio1 RK_PB6 GPIO_ACTIVE_LOW>;
> > + label = "DPAD-LEFT";
> > + linux,code = <BTN_DPAD_LEFT>;
> > + };
> > + sw4 {
> > + gpios = <&gpio1 RK_PB7 GPIO_ACTIVE_LOW>;
> > + label = "DPAD-RIGHT";
> > + linux,code = <BTN_DPAD_RIGHT>;
> > + };
> > + sw5 {
> > + gpios = <&gpio1 RK_PA2 GPIO_ACTIVE_LOW>;
> > + label = "BTN-A";
> > + linux,code = <BTN_EAST>;
> > + };
> > + sw6 {
> > + gpios = <&gpio1 RK_PA5 GPIO_ACTIVE_LOW>;
> > + label = "BTN-B";
> > + linux,code = <BTN_SOUTH>;
> > + };
> > + sw7 {
> > + gpios = <&gpio1 RK_PA6 GPIO_ACTIVE_LOW>;
> > + label = "BTN-Y";
> > + linux,code = <BTN_WEST>;
> > + };
> > + sw8 {
> > + gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_LOW>;
> > + label = "BTN-X";
> > + linux,code = <BTN_NORTH>;
> > + };
> > + sw9 {
> > + gpios = <&gpio2 RK_PA0 GPIO_ACTIVE_LOW>;
> > + label = "F1";
> > + linux,code = <BTN_TRIGGER_HAPPY1>;
> > + };
> > + sw10 {
> > + gpios = <&gpio2 RK_PA1 GPIO_ACTIVE_LOW>;
> > + label = "F2";
> > + linux,code = <BTN_TRIGGER_HAPPY2>;
> > + };
> > + sw11 {
> > + gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_LOW>;
> > + label = "F3";
> > + linux,code = <BTN_TRIGGER_HAPPY3>;
> > + };
> > + sw12 {
> > + gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_LOW>;
> > + label = "F4";
> > + linux,code = <BTN_TRIGGER_HAPPY4>;
> > + };
> > + sw13 {
> > + gpios = <&gpio2 RK_PA4 GPIO_ACTIVE_LOW>;
> > + label = "F5";
> > + linux,code = <BTN_TRIGGER_HAPPY5>;
> > + };
> > + sw14 {
> > + gpios = <&gpio2 RK_PA5 GPIO_ACTIVE_LOW>;
> > + label = "F6";
> > + linux,code = <BTN_TRIGGER_HAPPY6>;
> > + };
> > + sw15 {
> > + gpios = <&gpio2 RK_PA6 GPIO_ACTIVE_LOW>;
> > + label = "TOP-LEFT";
> > + linux,code = <BTN_TL>;
> > + };
> > + sw16 {
> > + gpios = <&gpio2 RK_PA7 GPIO_ACTIVE_LOW>;
> > + label = "TOP-RIGHT";
> > + linux,code = <BTN_TR>;
> > + };
> > + };
> > +
> > + leds: gpio-leds {
> > + compatible = "gpio-leds";
> > + pinctrl-names = "led_pins";
> > + pinctrl-0 = <&led_pins>;
> > +
> > + /* Blue LED : GPIO0_C1 */
> > + heartbeat {
> > + label = "blue:heartbeat";
> > + gpios = <&gpio0 RK_PC1 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "heartbeat";
> > + };
> > + };
> > +
>
> > + backlight: backlight {
> > + compatible = "pwm-backlight";
> > + power-supply = <&vcc_bl>;
> > + pwms = <&pwm1 0 25000 0>;
> > + };
>
> sort nodenames
>
> > +
> > + vccsys: vccsys {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc3v8_sys";
> > + regulator-always-on;
> > + regulator-min-microvolt = <3800000>;
> > + regulator-max-microvolt = <3800000>;
> > + };
> > +
> > + vcc_host: vcc_host {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc_host";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > +
> > + gpio = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + regulator-always-on;
> > + vin-supply = <&vccsys>;
> > + };
> > +};
> > +
> > +&cpu0 {
> > + cpu-supply = <&vdd_arm>;
> > +};
> > +
> > +&cpu1 {
> > + cpu-supply = <&vdd_arm>;
> > +};
> > +
> > +&cpu2 {
> > + cpu-supply = <&vdd_arm>;
> > +};
> > +
> > +&cpu3 {
> > + cpu-supply = <&vdd_arm>;
> > +};
> > +
> > +&cru {
> > + assigned-clocks = <&cru PLL_NPLL>,
> > + <&cru ACLK_BUS_PRE>, <&cru ACLK_PERI_PRE>,
> > + <&cru HCLK_BUS_PRE>, <&cru HCLK_PERI_PRE>,
> > + <&cru PCLK_BUS_PRE>, <&cru SCLK_GPU>,
> > + <&cru PLL_CPLL>;
> > +
> > + assigned-clock-rates = <1188000000>,
> > + <200000000>, <200000000>,
> > + <150000000>, <150000000>,
> > + <100000000>, <200000000>,
> > + <17000000>;
> > +};
> > +
> > +&display_subsystem {
> > + status = "okay";
> > +};
> > +
> > +&dsi {
> > + status = "okay";
> > +
> > + ports {
> > + mipi_out: port@1 {
> > + reg = <1>;
> > +
> > + mipi_out_panel: endpoint {
> > + remote-endpoint = <&mipi_in_panel>;
> > + };
> > + };
> > + };
> > +
> > + panel@0 {
> > + compatible = "elida,kd35t133";
> > + reg = <0>;
> > + backlight = <&backlight>;
> > + iovcc-supply = <&vcc_lcd>;
> > + reset-gpios = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>;
> > + vdd-supply = <&vcc_lcd>;
> > +
> > + port {
> > + mipi_in_panel: endpoint {
> > + remote-endpoint = <&mipi_out_panel>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&dsi_dphy {
> > + status = "okay";
> > +};
> > +
> > +&gpu {
> > + mali-supply = <&vdd_logic>;
> > + status = "okay";
> > +};
> > +
> > +&i2c0 {
>
> > + status = "okay";
>
> status below
>
> > + clock-frequency = <400000>;
>
> > + i2c-scl-rising-time-ns = <280>;
> > + i2c-scl-falling-time-ns = <16>;
>
> sort
>
> > +
> > + rk817: pmic@20 {
> > + compatible = "rockchip,rk817";
> > + reg = <0x20>;
> > + interrupt-parent = <&gpio0>;
> > + interrupts = <RK_PB2 IRQ_TYPE_LEVEL_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pmic_int>;
> > + rockchip,system-power-controller;
> > + wakeup-source;
> > + #clock-cells = <1>;
> > + clock-output-names = "rk808-clkout1", "xin32k";
> > +
> > + vcc1-supply = <&vccsys>;
> > + vcc2-supply = <&vccsys>;
> > + vcc3-supply = <&vccsys>;
> > + vcc4-supply = <&vccsys>;
> > + vcc5-supply = <&vccsys>;
> > + vcc6-supply = <&vccsys>;
> > + vcc7-supply = <&vccsys>;
> > +
> > + regulators {
> > + vdd_logic: DCDC_REG1 {
> > + regulator-name = "vdd_logic";
> > + regulator-min-microvolt = <950000>;
> > + regulator-max-microvolt = <1150000>;
> > + regulator-ramp-delay = <6001>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > +
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <950000>;
> > + };
> > + };
> > +
> > + vdd_arm: DCDC_REG2 {
> > + regulator-name = "vdd_arm";
> > + regulator-min-microvolt = <950000>;
> > + regulator-max-microvolt = <1350000>;
> > + regulator-ramp-delay = <6001>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > +
> > + regulator-state-mem {
> > + regulator-off-in-suspend;
> > + regulator-suspend-microvolt = <950000>;
> > + };
> > + };
> > +
> > + vcc_ddr: DCDC_REG3 {
> > + regulator-name = "vcc_ddr";
> > + regulator-always-on;
> > + regulator-boot-on;
> > +
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + };
> > + };
> > +
> > + vcc_3v3: DCDC_REG4 {
> > + regulator-name = "vcc_3v3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > +
> > + regulator-state-mem {
> > + regulator-off-in-suspend;
> > + regulator-suspend-microvolt = <3300000>;
> > + };
> > + };
> > +
> > + vcc_1v8: LDO_REG2 {
> > + regulator-name = "vcc_1v8";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > +
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <1800000>;
> > + };
> > + };
> > +
> > + vdd_1v0: LDO_REG3 {
> > + regulator-name = "vdd_1v0";
> > + regulator-min-microvolt = <1000000>;
> > + regulator-max-microvolt = <1000000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > +
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <1000000>;
> > + };
> > + };
> > +
> > + vcc3v3_pmu: LDO_REG4 {
> > + regulator-name = "vcc3v3_pmu";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > +
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <3300000>;
> > + };
> > + };
> > +
> > + vccio_sd: LDO_REG5 {
> > + regulator-name = "vccio_sd";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > +
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <3300000>;
> > + };
> > + };
> > +
> > + vcc_sd: LDO_REG6 {
> > + regulator-name = "vcc_sd";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > +
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <3300000>;
> > + };
> > + };
> > +
> > + vcc_bl: LDO_REG7 {
> > + regulator-name = "vcc_bl";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > +
> > + regulator-state-mem {
> > + regulator-off-in-suspend;
> > + regulator-suspend-microvolt = <3300000>;
> > + };
> > + };
> > +
> > + vcc_lcd: LDO_REG8 {
> > + regulator-name = "vcc_lcd";
> > + regulator-min-microvolt = <2800000>;
> > + regulator-max-microvolt = <2800000>;
> > +
> > + regulator-state-mem {
> > + regulator-off-in-suspend;
> > + regulator-suspend-microvolt = <2800000>;
> > + };
> > + };
> > +
> > + vcc_cam: LDO_REG9 {
> > + regulator-name = "vcc_cam";
> > + regulator-min-microvolt = <3000000>;
> > + regulator-max-microvolt = <3000000>;
> > +
> > + regulator-state-mem {
> > + regulator-off-in-suspend;
> > + regulator-suspend-microvolt = <3000000>;
> > + };
> > + };
> > + };
> > + };
> > +};
> > +
> > +/* EXT Header(P2) : 7(SCL:GPIO0.C2), 8(SDA:GPIO0.C3) */
> > +&i2c1 {
>
> > + status = "okay";
>
> status below
>
> > + clock-frequency = <400000>;
> > +};
> > +
> > +/* I2S 1 Channel Used */
> > +&i2s1_2ch {
>
> > + status = "okay";
>
> status below
>
> > + #sound-dai-cells = <0>;
> > +};
> > +
> > +&io_domains {
> > + vccio1-supply = <&vcc_3v3>;
> > + vccio2-supply = <&vccio_sd>;
> > + vccio3-supply = <&vcc_3v3>;
> > + vccio4-supply = <&vcc_3v3>;
> > + vccio5-supply = <&vcc_3v3>;
> > + vccio6-supply = <&vcc_3v3>;
> > + status = "okay";
> > +};
> > +
> > +&pmu_io_domains {
> > + pmuio1-supply = <&vcc3v3_pmu>;
> > + pmuio2-supply = <&vcc3v3_pmu>;
> > + status = "okay";
> > +};
> > +
> > +&pwm1 {
> > + status = "okay";
> > +};
> > +
> > +&saradc {
> > + vref-supply = <&vcc_1v8>;
> > + status = "okay";
> > +};
> > +
> > +&sdmmc {
> > + bus-width = <4>;
> > + cap-sd-highspeed;
>
> > + card-detect-delay = <800>;
>
> Other dts use 200. Why we need 800?
>
> > + cd-gpios = <&gpio0 RK_PA3 GPIO_ACTIVE_LOW>;
> > + sd-uhs-sdr12;
> > + sd-uhs-sdr25;
> > + sd-uhs-sdr50;
> > + sd-uhs-sdr104;
> > + vmmc-supply = <&vcc_sd>;
> > + vqmmc-supply = <&vccio_sd>;
> > + status = "okay";
> > +};
> > +
> > +&tsadc {
> > + pinctrl-names = "gpio", "otpout";
> > + pinctrl-0 = <&tsadc_otp_gpio>;
> > + pinctrl-1 = <&tsadc_otp_out>;
> > + status = "okay";
> > +};
> > +
> > +&u2phy {
> > + status = "okay";
> > +
> > + u2phy_host: host-port {
> > + status = "okay";
> > + };
> > +
> > + u2phy_otg: otg-port {
> > + status = "disabled";
> > + };
> > +};
> > +
> > +&usb20_otg {
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart1_xfer &uart1_cts>;
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart2m1_xfer>;
> > + status = "okay";
> > +};
> > +
> > +&vopb {
> > + status = "okay";
> > +};
> > +
> > +&vopb_mmu {
> > + status = "okay";
> > +};
> > +
> > +&pinctrl {
> > + pmic {
> > + pmic_int: pmic-int {
> > + rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
> > + };
> > +
> > + dc_det: dc-det {
> > + rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
> > + };
> > + };
> > +
> > + leds {
> > + led_pins: led-pins {
> > + rockchip,pins = <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
> > + };
> > + };
> > +
> > + btns {
> > + btn_pins: btn-pins {
> > + rockchip,pins = <1 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>,
> > + <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>,
> > + <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up>,
> > + <1 RK_PB7 RK_FUNC_GPIO &pcfg_pull_up>,
> > + <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>,
> > + <1 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>,
> > + <1 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
> > + <1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>,
> > +
> > + <2 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>,
> > + <2 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>,
> > + <2 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>,
> > + <2 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>,
> > + <2 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>,
> > + <2 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>,
> > + <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
> > + <2 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>;
> > + };
> > + };
> > +};
> > --
> > 2.24.1
>
>
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2020-03-07 13:48 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-03-06 21:09 [PATCH 1/3] arm64: dts: rockchip: add core devicetree for rk3326 Heiko Stuebner
2020-03-06 21:09 ` [PATCH 2/3] dt-bindings: Add binding for Hardkernel Odroid Go Advance Heiko Stuebner
2020-03-06 21:09 ` [PATCH 3/3] arm64: dts: rockchip: add Odroid Advance Go Heiko Stuebner
2020-03-07 8:36 ` Johan Jonker
2020-03-07 13:47 ` Heiko Stübner
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).