[PATCH net-next v6 10/11] arm64: dts: ti: k3-j721e-common-proc-board: add mcu cpsw nuss pinmux and phy defs

From: Grygorii Strashko <grygorii.strashko@ti.com>
To: Peter Ujfalusi <peter.ujfalusi@ti.com>,
	Rob Herring <robh@kernel.org>, Tero Kristo <t-kristo@ti.com>,
	"David S . Miller" <davem@davemloft.net>,
	netdev <netdev@vger.kernel.org>, Roger Quadros <rogerq@ti.com>,
	<devicetree@vger.kernel.org>, Jakub Kicinski <kuba@kernel.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>,
	Sekhar Nori <nsekhar@ti.com>,
	linux-kernel@vger.kernel.org,
	Kishon Vijay Abraham I <kishon@ti.com>,
	Murali Karicheri <m-karicheri2@ti.com>,
	linux-arm-kernel@lists.infradead.org
Subject: [PATCH net-next v6 10/11] arm64: dts: ti: k3-j721e-common-proc-board: add mcu cpsw nuss pinmux and phy defs
Date: Tue, 24 Mar 2020 00:52:53 +0200	[thread overview]
Message-ID: <20200323225254.12759-11-grygorii.strashko@ti.com> (raw)
In-Reply-To: <20200323225254.12759-1-grygorii.strashko@ti.com>

The TI J721E EVM base board has TI DP83867 PHY connected to external CPSW
NUSS Port 1 in rgmii-rxid mode.

Hence, add pinmux and Ethernet PHY configuration for TI j721e SoC MCU
Gigabit Ethernet two ports Switch subsystem (CPSW NUSS).

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
---
 .../dts/ti/k3-j721e-common-proc-board.dts     | 43 +++++++++++++++++++
 1 file changed, 43 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index 7a5c3d4adadd..98e5e17e3ff7 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
@@ -8,6 +8,7 @@
 #include "k3-j721e-som-p0.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/net/ti-dp83867.h>
 
 / {
 	chosen {
@@ -128,6 +129,30 @@
 			J721E_WKUP_IOPAD(0x38, PIN_INPUT, 0) /* (A23) MCU_OSPI1_LBCLKO */
 		>;
 	};
+
+	mcu_cpsw_pins_default: mcu_cpsw_pins_default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
+			J721E_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
+			J721E_WKUP_IOPAD(0x0060, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
+			J721E_WKUP_IOPAD(0x0064, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
+			J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
+			J721E_WKUP_IOPAD(0x006c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
+			J721E_WKUP_IOPAD(0x0078, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
+			J721E_WKUP_IOPAD(0x007c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
+			J721E_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
+			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
+			J721E_WKUP_IOPAD(0x0070, PIN_INPUT, 0) /* MCU_RGMII1_TXC */
+			J721E_WKUP_IOPAD(0x0074, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
+		>;
+	};
+
+	mcu_mdio_pins_default: mcu_mdio1_pins_default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* MCU_MDIO0_MDC */
+			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_MDIO0_MDIO */
+		>;
+	};
 };
 
 &wkup_uart0 {
@@ -429,3 +454,21 @@
 		#gpio-cells = <2>;
 	};
 };
+
+&mcu_cpsw {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
+};
+
+&davinci_mdio {
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+	};
+};
+
+&cpsw_port1 {
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&phy0>;
+};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
