[PATCH AUTOSEL 5.5 01/35] ARM: dts: sun8i-a83t-tbs-a711: HM5065 doesn't like such a high voltage

[PATCH AUTOSEL 5.5 01/35] ARM: dts: sun8i-a83t-tbs-a711: HM5065 doesn't like such a high voltage

[Sasha Levin]

From: Ondrej Jirman <megous@megous.com>

[ Upstream commit a40550952c000667b20082d58077bc647da6c890 ]

Lowering the voltage solves the quick image degradation over time
(minutes), that was probably caused by overheating.

Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts b/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts
index f781d330cff50..e8b3669e0e5d8 100644
--- a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts
@@ -374,8 +374,8 @@
 };
 
 &reg_dldo3 {
-	regulator-min-microvolt = <2800000>;
-	regulator-max-microvolt = <2800000>;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
 	regulator-name = "vdd-csi";
 };
 
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.5 02/35] bus: sunxi-rsb: Return correct data when mixing 16-bit and 8-bit reads

[Sasha Levin]

From: Ondrej Jirman <megous@megous.com>

[ Upstream commit a43ab30dcd4a1abcdd0d2461bf1cf7c0817f6cd3 ]

When doing a 16-bit read that returns data in the MSB byte, the
RSB_DATA register will keep the MSB byte unchanged when doing
the following 8-bit read. sunxi_rsb_read() will then return
a result that contains high byte from 16-bit read mixed with
the 8-bit result.

The consequence is that after this happens the PMIC's regmap will
look like this: (0x33 is the high byte from the 16-bit read)

% cat /sys/kernel/debug/regmap/sunxi-rsb-3a3/registers
00: 33
01: 33
02: 33
03: 33
04: 33
05: 33
06: 33
07: 33
08: 33
09: 33
0a: 33
0b: 33
0c: 33
0d: 33
0e: 33
[snip]

Fix this by masking the result of the read with the correct mask
based on the size of the read. There are no 16-bit users in the
mainline kernel, so this doesn't need to get into the stable tree.

Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/bus/sunxi-rsb.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/bus/sunxi-rsb.c b/drivers/bus/sunxi-rsb.c
index be79d6c6a4e45..1bb00a959c67f 100644
--- a/drivers/bus/sunxi-rsb.c
+++ b/drivers/bus/sunxi-rsb.c
@@ -345,7 +345,7 @@ static int sunxi_rsb_read(struct sunxi_rsb *rsb, u8 rtaddr, u8 addr,
 	if (ret)
 		goto unlock;
 
-	*buf = readl(rsb->regs + RSB_DATA);
+	*buf = readl(rsb->regs + RSB_DATA) & GENMASK(len * 8 - 1, 0);
 
 unlock:
 	mutex_unlock(&rsb->lock);
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.5 12/35] soc: fsl: dpio: register dpio irq handlers after dpio create

[Sasha Levin]

From: Grigore Popescu <grigore.popescu@nxp.com>

[ Upstream commit fe8fe7723a3a824790bda681b40efd767e2251a7 ]

The dpio irqs must be registered when you can actually
receive interrupts, ie when the dpios are created.
Kernel goes through NULL pointer dereference errors
followed by kernel panic [1] because the dpio irqs are
enabled before the dpio is created.

[1]
Unable to handle kernel NULL pointer dereference at virtual address 0040
fsl_mc_dpio dpio.14: probed
fsl_mc_dpio dpio.13: Adding to iommu group 11
  ISV = 0, ISS = 0x00000004
Unable to handle kernel NULL pointer dereference at virtual address 0040
Mem abort info:
  ESR = 0x96000004
  EC = 0x25: DABT (current EL), IL = 32 bits
  SET = 0, FnV = 0
  EA = 0, S1PTW = 0
Data abort info:
  ISV = 0, ISS = 0x00000004
  CM = 0, WnR = 0
[0000000000000040] user address but active_mm is swapper
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Modules linked in:
CPU: 2 PID: 151 Comm: kworker/2:1 Not tainted 5.6.0-rc4-next-20200304 #1
Hardware name: NXP Layerscape LX2160ARDB (DT)
Workqueue: events deferred_probe_work_func
pstate: 00000085 (nzcv daIf -PAN -UAO)
pc : dpaa2_io_irq+0x18/0xe0
lr : dpio_irq_handler+0x1c/0x28
sp : ffff800010013e20
x29: ffff800010013e20 x28: ffff0026d9b4c140
x27: ffffa1d38a142018 x26: ffff0026d2953400
x25: ffffa1d38a142018 x24: ffffa1d38a7ba1d8
x23: ffff800010013f24 x22: 0000000000000000
x21: 0000000000000072 x20: ffff0026d2953400
x19: ffff0026d2a68b80 x18: 0000000000000001
x17: 000000002fb37f3d x16: 0000000035eafadd
x15: ffff0026d9b4c5b8 x14: ffffffffffffffff
x13: ff00000000000000 x12: 0000000000000038
x11: 0101010101010101 x10: 0000000000000040
x9 : ffffa1d388db11e4 x8 : ffffa1d38a7e40f0
x7 : ffff0026da414f38 x6 : 0000000000000000
x5 : ffff0026da414d80 x4 : ffff5e5353d0c000
x3 : ffff800010013f60 x2 : ffffa1d388db11c8
x1 : ffff0026d2a67c00 x0 : 0000000000000000
Call trace:
 dpaa2_io_irq+0x18/0xe0
 dpio_irq_handler+0x1c/0x28
 __handle_irq_event_percpu+0x78/0x2c0
 handle_irq_event_percpu+0x38/0x90
 handle_irq_event+0x4c/0xd0
 handle_fasteoi_irq+0xbc/0x168
 generic_handle_irq+0x2c/0x40
 __handle_domain_irq+0x68/0xc0
 gic_handle_irq+0x64/0x150
 el1_irq+0xb8/0x180
 _raw_spin_unlock_irqrestore+0x14/0x48
 irq_set_affinity_hint+0x6c/0xa0
 dpaa2_dpio_probe+0x2a4/0x518
 fsl_mc_driver_probe+0x28/0x70
 really_probe+0xdc/0x320
 driver_probe_device+0x5c/0xf0
 __device_attach_driver+0x88/0xc0
 bus_for_each_drv+0x7c/0xc8
 __device_attach+0xe4/0x140
 device_initial_probe+0x18/0x20
 bus_probe_device+0x98/0xa0
 device_add+0x41c/0x758
 fsl_mc_device_add+0x184/0x530
 dprc_scan_objects+0x280/0x370
 dprc_probe+0x124/0x3b0
 fsl_mc_driver_probe+0x28/0x70
 really_probe+0xdc/0x320
 driver_probe_device+0x5c/0xf0
 __device_attach_driver+0x88/0xc0
 bus_for_each_drv+0x7c/0xc8
 __device_attach+0xe4/0x140
 device_initial_probe+0x18/0x20
 bus_probe_device+0x98/0xa0
 deferred_probe_work_func+0x74/0xa8
 process_one_work+0x1c8/0x470
 worker_thread+0x1f8/0x428
 kthread+0x124/0x128
 ret_from_fork+0x10/0x18
Code: a9bc7bfd 910003fd a9025bf5 a90363f7 (f9402015)
---[ end trace 38298e1a29e7a570 ]---
Kernel panic - not syncing: Fatal exception in interrupt
SMP: stopping secondary CPUs
Mem abort info:
  ESR = 0x96000004
  CM = 0, WnR = 0
  EC = 0x25: DABT (current EL), IL = 32 bits
[0000000000000040] user address but active_mm is swapper
  SET = 0, FnV = 0
  EA = 0, S1PTW = 0
Data abort info:
  ISV = 0, ISS = 0x00000004
  CM = 0, WnR = 0
[0000000000000040] user address but active_mm is swapper
SMP: failed to stop secondary CPUs 0-2
Kernel Offset: 0x21d378600000 from 0xffff800010000000
PHYS_OFFSET: 0xffffe92180000000
CPU features: 0x10002,21806008
Memory Limit: none
---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Grigore Popescu <grigore.popescu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/soc/fsl/dpio/dpio-driver.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/soc/fsl/dpio/dpio-driver.c b/drivers/soc/fsl/dpio/dpio-driver.c
index 70014ecce2a7e..7b642c330977f 100644
--- a/drivers/soc/fsl/dpio/dpio-driver.c
+++ b/drivers/soc/fsl/dpio/dpio-driver.c
@@ -233,10 +233,6 @@ static int dpaa2_dpio_probe(struct fsl_mc_device *dpio_dev)
 		goto err_allocate_irqs;
 	}
 
-	err = register_dpio_irq_handlers(dpio_dev, desc.cpu);
-	if (err)
-		goto err_register_dpio_irq;
-
 	priv->io = dpaa2_io_create(&desc, dev);
 	if (!priv->io) {
 		dev_err(dev, "dpaa2_io_create failed\n");
@@ -244,6 +240,10 @@ static int dpaa2_dpio_probe(struct fsl_mc_device *dpio_dev)
 		goto err_dpaa2_io_create;
 	}
 
+	err = register_dpio_irq_handlers(dpio_dev, desc.cpu);
+	if (err)
+		goto err_register_dpio_irq;
+
 	dev_info(dev, "probed\n");
 	dev_dbg(dev, "   receives_notifications = %d\n",
 		desc.receives_notifications);
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.5 16/35] net: stmmac: platform: Fix misleading interrupt error msg

[Sasha Levin]

From: Markus Fuchs <mklntf@gmail.com>

[ Upstream commit fc191af1bb0d069dc7e981076e8b80af21f1e61d ]

Not every stmmac based platform makes use of the eth_wake_irq or eth_lpi
interrupts. Use the platform_get_irq_byname_optional variant for these
interrupts, so no error message is displayed, if they can't be found.
Rather print an information to hint something might be wrong to assist
debugging on platforms which use these interrupts.

Signed-off-by: Markus Fuchs <mklntf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../net/ethernet/stmicro/stmmac/stmmac_platform.c  | 14 ++++++++++----
 1 file changed, 10 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index d10ac54bf385a..13fafd905db87 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -663,16 +663,22 @@ int stmmac_get_platform_resources(struct platform_device *pdev,
 	 * In case the wake up interrupt is not passed from the platform
 	 * so the driver will continue to use the mac irq (ndev->irq)
 	 */
-	stmmac_res->wol_irq = platform_get_irq_byname(pdev, "eth_wake_irq");
+	stmmac_res->wol_irq =
+		platform_get_irq_byname_optional(pdev, "eth_wake_irq");
 	if (stmmac_res->wol_irq < 0) {
 		if (stmmac_res->wol_irq == -EPROBE_DEFER)
 			return -EPROBE_DEFER;
+		dev_info(&pdev->dev, "IRQ eth_wake_irq not found\n");
 		stmmac_res->wol_irq = stmmac_res->irq;
 	}
 
-	stmmac_res->lpi_irq = platform_get_irq_byname(pdev, "eth_lpi");
-	if (stmmac_res->lpi_irq == -EPROBE_DEFER)
-		return -EPROBE_DEFER;
+	stmmac_res->lpi_irq =
+		platform_get_irq_byname_optional(pdev, "eth_lpi");
+	if (stmmac_res->lpi_irq < 0) {
+		if (stmmac_res->lpi_irq == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+		dev_info(&pdev->dev, "IRQ eth_lpi not found\n");
+	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	stmmac_res->addr = devm_ioremap_resource(&pdev->dev, res);
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.5 34/35] i2c: st: fix missing struct parameter description

[Sasha Levin]

From: Alain Volmat <avolmat@me.com>

[ Upstream commit f491c6687332920e296d0209e366fe2ca7eab1c6 ]

Fix a missing struct parameter description to allow
warning free W=1 compilation.

Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/i2c/busses/i2c-st.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/i2c/busses/i2c-st.c b/drivers/i2c/busses/i2c-st.c
index 54e1fc8a495e7..f7f7b5b64720e 100644
--- a/drivers/i2c/busses/i2c-st.c
+++ b/drivers/i2c/busses/i2c-st.c
@@ -434,6 +434,7 @@ static void st_i2c_wr_fill_tx_fifo(struct st_i2c_dev *i2c_dev)
 /**
  * st_i2c_rd_fill_tx_fifo() - Fill the Tx FIFO in read mode
  * @i2c_dev: Controller's private data
+ * @max: Maximum amount of data to fill into the Tx FIFO
  *
  * This functions fills the Tx FIFO with fixed pattern when
  * in read mode to trigger clock.
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel